Development of a Biocompatible Solid Phase Microextraction Thin Film Coating for the Sampling and Enrichment of Peptides

Recent advance on microextraction sampling technologies for bioanalysis

The contents of target substances in biological samples are usually at low concentration levels, and the matrix of biological samples is usually complex. Sample preparation is considered a very critical step in bioanalysis. At present, the utilization of microextraction sampling technology has gained considerable prevalence in the realm of biological analysis. The key developments in this field focus on the efficient microextraction media and the miniaturization and automation of adaptable sample preparation methods currently. In this review, the recent progress on the microextraction sampling technologies for bioanalysis has been introduced from point of view of the preparation of microextraction media and the microextraction sampling strategies. The advance on the microextraction media was reviewed in detail, mainly including the aptamer-functionalized materials, molecularly imprinted polymers, carbon-based materials, metal-organic frameworks, covalent organic frameworks, etc. The advance on the microextraction sampling technologies was summarized mainly based on in-vivo sampling, in-vitro sampling and microdialysis technologies. Moreover, the current challenges and perspective on the future trends of microextraction sampling technologies for bioanalysis were briefly discussed.

Proteomic Analysis of Human Saliva via Solid-Phase Microextraction Coupled with Liquid Chromatography-Mass Spectrometry

Proteomics of human saliva samples was achieved for the first time via biocompatible solid-phase microextraction (bio-SPME) devices. Upon introduction of a porogen to a conventional C18 coating, porous C18/polyacrylonitrile (PAN) SPME blades were able to extract peptides up to 3.0 kDa and more peptides than commercial SPME blades. Following Trypsin digestion, salivary proteomic analysis was achieved via SPME-LC-MS/MS. Seven endogenous proteins were consistently identified in all saliva samples via bio-SPME. Taking advantage of this strategy, untargeted peptidomics was applied for the comparison of saliva samples between healthy and SARS-CoV-2 positive individuals. The results showed clear peptidomic differences between the viral and healthy saliva samples. This proof-of-concept study demonstrates the potential of bio-SPME-LC-MS/MS for peptidomics and proteomics in biomedical applications.

Physisorption Behaviors of Organochlorine Pesticides on the InP3 Monolayer from Theoretical Insight

Dichlorodiphenyltrichloroethane (DDT), hexachlorocyclohexane (BHC), aldrin, and chlordimeform are ubiquitous organochlorine pesticide (OCP) residues in the environment, which pose a great threat to human health and ecosystems due to their high toxicity and easy accumulation. Based on the density functional theory (DFT) calculations, a two-dimensional InP3 monolayer was selected as a sensing material to study the sensitivity detection and adsorption behaviors toward BHC, aldrin, chlordimeform, and DDT. The calculation results show that four pesticide molecules are adsorbed on the InP3 surface by physical interaction. The identified response values (69.1, -43.1%) for DDT and chlordimeform reveal the potential of the InP3 monolayer as a sensing material for the detection of these two pesticides, accompanied by the achievement of cyclic utilization by heating to 498 K. The most satisfactory result is the adsorption of BHC, owing to the admirable sensing response (62.7%) and short recovery time (1.8 s) at room temperature, which makes InP3 a promising pesticide sensor for BHC. However, the InP3 surface is unsuitable for aldrin sensing due to poor response (-1.9%). Our work gives theoretical insight into the good sensitivity and recycling of the InP3 monolayer as a new pesticide sensor to detect DDT, BHC, and chlordimeform, which further broadens the application prospect of the InP3 nanosheet into the sensitive detection of organochlorine pesticides in the ecological environment.

Performance Evaluation of Extraction Coatings with Different Sorbent Particles and Binder Composition

Binders are critical components used in the preparation of a range of extraction devices, including solid-phase microextraction (SPME) devices. While the main role of a binder is to affix the sorbent particles to the selected support, it is critical to select the optimal binder to ensure that it does not negatively impact the coating's particle sorption capability. This work presents the first comprehensive investigation of the interactions between binders and solid sorbent particles as these interactions can significantly impact the performance of the coating. Specifically, the findings presented herein provide a better understanding of the extraction mechanisms of composite coatings and new rules for predicting the particle adhesion forces and binder distribution in the coating. The influence of binder chemistry on coating performance is investigated by examining a selection of the most used binders, namely, polydimethylsiloxane (PDMS), polyacrylonitrile (PAN), poly(vinylidene difluoride) (PVDF), polytetrafluoroethylene amorphous fluoroplastics (PTFE AF 2400), and polybenzimidazole (PBI). The solid particles (e.g., hydrophilic-lipophilic balanced (HLB) and C18) used in this work were selected for their ability to provide optimal extraction coverage for a broad range of analytes. The results show that PDMS does not change the properties of the solid particles and that the binder occupies a negligible volume due to shrinking after polymerization, resulting in the solid particles making up most of the coating volume. Hence, the coating sorption characteristics correspond closely to the properties of the selected solid particles. On the other hand, the results also showed that PTFE AF 2400 can interact with the active surface of the sorbent, leading to the deactivation of the sorbent particles. Therefore, the extraction performance and permeability coefficients decrease as the size of the penetrant increases, indicating a rigid porous structure. The results of this study can aid in the optimization of SPME devices as they provide reference values that can be used to determine the optimal binder and the sorbent affinity for the targeted compounds. Finally, the present work also provides the broader scientific community with a strategy for investigating the properties of sorbent particle/binder structures and defines the characteristics of a good coating/membrane by analyzing all parameters such as kinetics, thermodynamic equilibria, and morphology.

Point-of-care applicable metabotyping using biofluid-specific electrospun MetaSAMPs directly amenable to ambient LA-REIMS

In recent years, ambient ionization mass spectrometry (AIMS) including laser ablation rapid evaporation IMS, has enabled direct biofluid metabolome analysis. AIMS procedures are, however, still hampered by both analytical, i.e., matrix effects, and practical, i.e., sample transport stability, drawbacks that impede metabolome coverage. In this study, we aimed at developing biofluid-specific metabolome sampling membranes (MetaSAMPs) that offer a directly applicable and stabilizing substrate for AIMS. Customized rectal, salivary, and urinary MetaSAMPs consisting of electrospun (nano)fibrous membranes of blended hydrophilic (polyvinylpyrrolidone and polyacrylonitrile) and lipophilic (polystyrene) polymers supported metabolite absorption, adsorption, and desorption. Moreover, MetaSAMP demonstrated superior metabolome coverage and transport stability compared to crude biofluid analysis and was successfully validated in two pediatric cohorts (MetaBEAse, n = 234 and OPERA, n = 101). By integrating anthropometric and (patho)physiological with MetaSAMP-AIMS metabolome data, we obtained substantial weight-driven predictions and clinical correlations. In conclusion, MetaSAMP holds great clinical application potential for on-the-spot metabolic health stratification.

Aptamer-functionalized stir bar sorptive extraction for selective isolation, identification, and determination of concanavalin A in food by MALDI-TOF-MS

An aptamer-functionalized stir bar sorptive extraction (SBSE) coating is described for the first time devoted to selective isolation and preconcentration of an allergenic food protein, concavanalin A (Con A), followed by matrix-assisted laser desorption/ionization mass spectrometry (MALDI-TOF-MS) determination. For this purpose, the polytetrafluoroethylene surface of commercial magnetic stir bars was properly modified and vinylized to immobilize a thiol-modified aptamer against Con A via straightforward "thiol-ene" click chemistry. The aptamer-functionalized stir bar was employed as SBSE sorbent to isolate Con A, and several parameters that can affect the extraction efficiency were investigated. Under the optimized conditions, Con A was extracted and desorbed during 30 and 45 min, respectively, at 25 °C and 600 rpm. The SBSE MALDI-TOF-MS method provided limits of detection of 0.5 μg mL^-1 for Con A. Furthermore, the SBSE coating was highly selective to Con A compared to other lectins. The developed method was successfully applied to the determination of low levels of Con A in several food matrices (i.e., white beans as well as chickpea, lentils, and wheat flours). Recoveries ranged from 81 to 97% with relative standard deviations below 7%. The aptamer-based stir bars presented suitable physical and chemical long-term stability (1 month) and a reusability of 10 and 5 extraction cycles with standards and food extracts, respectively. The developed aptamer-affinity extraction devices open up the possibility of developing novel highly selective SBSE coatings for the extraction of proteins and peptides from complex samples.

Cellulose Nanocrystals Induced Loose and Porous Graphite Phase Carbon Nitride/Porous Carbon Composites for Capturing and Determining of Organochlorine Pesticides from Water and Fruit Juice by Solid-Phase Microextraction

Herein, novel, loose, and porous graphite phase carbon nitride/porous carbon (g-C₃N₄@PC) composites were prepared by decorating cellulose nanocrystals (CNCs). The characterization results demonstrate that the as-prepared composites presented high specific surface areas, porous structures, and abundant chemical groups, with the modification of CNCs. In view of the unique advantages, g-C₃N₄@PC was used as the coating material for the solid-phase microextraction (SPME) of organochlorine pesticides (OCPs) in water and juice samples. The g-C₃N₄@PC-coated fibers showed better extraction efficiencies than commercial fibers (100/7 μm PDMS and PA) toward the OCPs, with the enrichment factors of the g-C₃N₄@PC-coated fibers 5-30 times higher than the latter. Using a gas chromatography-mass spectrometry (GC-MS) instrument, the g-C₃N₄@PC-coated fibers exhibited a gratifying analytical performance for determining low concentrations of OCPs, with a wide linear range (0.1-1600 ng L^-1 for water; 0.1-1000 ng L^-1 for juice), low limits of detection (0.0141-0.0942 ng L^-1 for water; 0.0245-0.0777 ng L^-1 for juice), and good reproducibility and repeatability in optimal conditions. The established method showed good sensitivity and recovery in the determination of OCPs in the water and fruit juice samples, which displayed broad prospects for analyzing organic pollutants from environmental samples.

Multifunctionalized Covalent Organic Frameworks for Broad-Spectrum Extraction and Ultrasensitive Analysis of Per- and Polyfluoroalkyl Substances

The contamination of surface and ground water by per- and polyfluoroalkyl substances (PFASs) has become a growing concern, and the structural diversity of PFASs is the major challenge for their ubiquitous applications. Strategies for monitoring coexistent anionic, cationic, and zwitterionic PFASs even at trace levels in aquatic environments are urgently demanded for effective pollution control. Herein, novel amide group and perfluoroalkyl chain-functionalized covalent organic frameworks (COFs) named COF-NH-CO-F9 are successfully synthesized and used for highly efficient extraction of broad-spectrum PFASs, attributing to their unique structure and the multifunctional groups. Under the optimal conditions, a simple and high-sensitivity method is established to quantify 14 PFASs including anionic, cationic, and zwitterionic species by coupling solid-phase microextraction (SPME) with ultrahigh-performance liquid chromatography-triple quadrupole mass spectrometry (UHPLC-MS/MS) for the first time. The established method displays high enrichment factors (EFs) of 66-160, ultrahigh sensitivity with low limits of detection (LODs) of 0.0035-0.18 ng L^-1, a wide linearity of 0.1-2000 ng L^-1 with correlation coefficient (R²) ≥0.9925, and satisfactory precision with relative standard deviations (RSDs) ≤11.2%. The excellent performance is validated in real water samples with recoveries of 77.1-108% and RSDs ≤11.4%. This work highlights the potential of rational design of COFs with the desired structure and functionality for the broad-spectrum enrichment and ultrasensitive determination of PFASs in real applications.

Preliminary Study on a Biocompatible Cellulose Waterborne Polyurethane Composite Membrane

A promising technique for repairing necrotic mucosa of human organs has emerged, in which composite films are used to replace human mucosa. In this work, neutral alpha-amylase corrosion solution with a concentration of 0.40 mg/mL and hydrochloric acid corrosion solution at pH 0.9 were used as simulated oral cavity and gastric fluid environments under the condition of human body temperature. The prepared cellulose film and the cellulose water-based polyurethane composite film (the concentration of water-based polyurethane was 90, 92, 94, 96, or 98%) were mixed in the simulated environment. The composite membrane had a weaker water swelling property (water swelling degree of 4.32%), weaker surface hydrophilicity (water contact angle of 59.05°), and stronger enzyme activity (1.77 U). This functional film composite material is expected to become an ideal substitute for human mucosa.

Polymeric Membranes for Oil-Water Separation: A Review

This review is devoted to the application of bulk synthetic polymers such as polysulfone (PSf), polyethersulfone (PES), polyacrylonitrile (PAN), and polyvinylidene fluoride (PVDF) for the separation of oil-water emulsions. Due to the high hydrophobicity of the presented polymers and their tendency to be contaminated with water-oil emulsions, methods for the hydrophilization of membranes based on them were analyzed: the mixing of polymers, the introduction of inorganic additives, and surface modification. In addition, membranes based on natural hydrophilic materials (cellulose and its derivatives) are given as a comparison.

Polyamide Noncoated Device for Adsorption-Based Microextraction and Novel 3D Printed Thin-Film Microextraction Supports

Polyamide noncoated device for adsorption-based microextraction (PANDA microextraction) is a brand new, easy to prepare, environmentally friendly, inexpensive, and efficient sample preparation method created entirely with the use of 3D printing. The proposed method is based on the extractive proprieties of the unmodified polyamide and carbon fiber blends and is compared with the highly selective thin-film microextraction (TFME). In addition, 3D printing was used to simplify the process of TFME. Prototype sample preparation devices were evaluated by the extraction of oral fluid spiked with 38 small molecules with diverse chemical natures, such as lipophilicity in the log P range of 0.2–7.2. The samples were analyzed by high-performance liquid chromatography coupled with tandem mass spectrometry. The results indicate that chemically and thermally resistant 3D printed supports can be successfully used as a cost-saving, environmentally friendly solution for the preparation of TFME devices, alternative to the conventional metal supports, with only marginal differences in the extraction yield (mean = 4.0%, median = 1.8%, range = 0.0–22.3%, n = 38). Even more remarkably, in some cases, the newly proposed PANDA microextraction method exceeded the reference TFME in terms of the extraction efficacy and offered excellent sample cleanup as favorable matrix effects were observed (mean = −8.5%, median = 7.5%, range = −34.7–20.0%, n = 20). This innovative approach paves the road to the simplified sample preparation with the use of emerging extractive 3D printing polymers.

Nitrogen-rich carbon nitride as solid-phase microextraction fiber coating for high-efficient pretreatment of polychlorinated biphenyls from environmental samples

A two-dimensional nitrogen-rich carbon nitrogen (C₃N₅) material was prepared via a facile high temperature thermal polymerization. For the first time, the C₃N₅ was used as fiber coating of solid-phase microextraction (SPME) to extract and preconcentrate polychlorinated biphenyls (PCBs) before gas chromatography (GC) analysis. The X-ray diffraction, N₂ adsorption-desorption, Fourier transform-infrared spectroscopy, thermogravimetric analysis, and X-ray photoelectron spectroscopy were performed to investigate structure, functional groups, thermal stability, bonding type, element composition, and atomic ratio of C₃N₅. The two-dimensional planar stacking structure was further verified by scanning electron microscopy and transmission electron microscopy. Five PCBs including PCB-4, PCB-12, PCB-29, PCB-52 and PCB-101 were selected as targets to evaluate performance of SPME fiber. Under the optimal conditions, the method showed a good linear range from 0.01 to 1000 ng/mL with the correlation coefficients (R²) higher than 0.9990. Enrichment factors of the method were obtained from 2045 to 3080. The limits of detection (LODs, S/N = 3) and limits of quantification (LOQs, S/N = 10) were calculated as 0.0031-0.0111 ng/mL and 0.01-0.05 ng/mL, respectively. The precisions of intra-day and inter-day were obtained with the relative standard deviations (RSDs) at 1.5-6.6% and 0.8-6.9%, respectively. The fiber-to-fiber producibility was achieved with RSDs ranged from 3.5% to 11.4%. The method was applied to detect PCBs in river water and soil samples. The contents were calculated at 0.040-0.147 ng/mL in water and 0.520-3.218 ng/g in soil. The C₃N₅ as SPME fiber coating material may be applied to extract and preconcentrate other environmental pollutants which have similar chemical structures with PCBs.

Porous Inorganic Materials for Bioanalysis and Diagnostic Applications

Porous inorganic materials play an important role in adsorbing targeted analytes and supporting efficient reactions in analytical science. The detection performance relies on the structural properties of porous materials, considering the tunable pore size, shape, connectivity, etc. Herein, we first clarify the enhancement mechanisms of porous materials for bioanalysis, concerning the detection sensitivity and selectivity. The diagnostic applications of porous material-assisted platforms by coupling with various analytical techniques, including electrochemical sensing, optical spectrometry, and mass spectrometry, etc., are then reviewed. We foresee that advanced porous materials will bring far-reaching implications in bioanalysis toward real-case applications, especially as diagnostic assays in clinical settings.

Gas-cycle-assisted headspace solid-phase microextraction coupled with gas chromatography for rapid analysis of organic pollutants

Herein, a new gas-cycle-assisted (GCA) headspace solid-phase microextraction (HS-SPME) device was designed to rapidly extract organic pollutants with high K_ow and boiling points, which have difficulty in volatilization from matrix to headspace. Organic pollutants, including three polycyclic aromatic hydrocarbons (PAHs), four polychlorinated biphenyls (PCBs), and five phthalate esters (PAEs), were selected to evaluate the performance of GCA HS-SPME. Compared with conventional HS-SPME, the equilibrium times of GCA HS-SPME for extraction of PAHs, PCBs, and PAEs were greatly shortened from 70-90 to 5-11 min. Moreover, the limits of detection for analysis of PAHs were achieved at pg mL^-1 level by GCA HS-SPME coupled with gas chromatography-flame ionization detection.

Thin film molecularly imprinted polymer (TF-MIP), a selective and single-use extraction device for high-throughput analysis of biological samples

Enhancing selectivity, reducing matrix effects and increasing analytical throughput have been the main objectives in the development of biological sample preparation techniques. A thin film molecularly imprinted polymer (MIP) is employed for extraction and analysis of tricyclic antidepressants (TCAs) as a model class of compounds in human plasma for the first time to reach the abovementioned goals. The thin film MIPs prepared on a metal substrate can be used directly for extraction from biological matrices with no sample manipulation steps and no pre-conditioning. This method was validated with good linearity (R² > 0.99 in 1.0-500.0 ng mL^-1 range), excellent accuracy (90% -110%) and precision (RSD % value less than 15%) in pooled human plasma samples (N = 3). The limits of quantitation (LOQ) for TCAs in plasma samples were between 1.0-5.0 ng mL^-1 which are lower than the therapeutic ranges of these drugs. Kinetic and isotherm studies showed the superior performance of MIP sorbent compared to a non-imprinted polymer (NIP) sorbent in extracting TCAs from a bovine serum albumin (BSA) solution. The optimized and validated method for pooled human plasma was utilized for monitoring the concentration of TCAs in three patient samples who had been prescribed TCAs. These selective single-use thin film extraction devices are promising for efficient and fast procedures for analyzing biological samples.

Exploiting arginine distributions for the selective and efficient depletion of arginine-rich plasma proteins

The number and arrangement of arginine (Arg) residues in protein chains contribute greatly to the selective capturing of proteins on a designed adsorbent consisting of organic phosphate functionalized fibrous SiO2 microspheres, and the efficient depletion of high abundance Arg-rich protein species from human plasma is achieved.