Methylene blue-mediated electrocatalytic detection of hexavalent chromium

Colorimetric Sensor for Cr(VI) Ion Detection in Tap Water Using a Combination of AuNPs and AgNPs

Colorimetric sensors are a promising technique for the simple screening of water, food, and environmental samples contaminated with interferents, allowing for color changes to be observed with the naked eye or a spectrophotometer. In this study, a colorimetric sensor for the selective detection of hexavalent chromium ion (Cr(VI)) contamination in water was developed. A combination of sodium borohydride-coated gold and citrate-capped silver nanoparticles (Na-AuNPs/cit-AgNPs) was employed as a colorimetric probe. Upon the addition of Cr(VI)-contaminated tap water in the colorimetric probe solution, the color sequentially transitioned from its initial orange to dark reddish-purple, dark purplish-red, dark blue-violet, and gray. This colorimetric strategy relies on AgNP dissolution and AuNP aggregation in the presence of the Cr(VI) ions. The dissolution of AgNPs is evidenced by the reduction of the characteristic peak of AgNPs at 400 nm, while the aggregation of AuNPs leads to a red shift in the absorption band at 514 nm, accompanied by broad absorption in the 500-700 nm range. The limits of detections were found to be 22.9 and 50 ppb using a spectrometer and by visual observation, respectively. The synthesized AuNPs and AgNPs are very stable in the presence of media containing complicated ions. We further demonstrated the practical applicability of the developed system for detecting Cr(VI) in real samples, including natural water and artificial urine, highlighting its potential for addressing Cr(VI) contamination in practical scenarios.

Facile synthesis of sulphur-doped carbon dots (S-CDs) using a hydrothermal method for the selective sensing of Cr6+ and Fe3+ ions: application to environmental water sample analysis

In this work, we used a one-step hydrothermal method to synthesize blue-emission sulfur-doped carbon dots (S-CDs) using jaggery as a carbon precursor. The synthesized carbon quantum dots showed low toxicity, good water solubility, anti-interference properties, and stable fluorescence. When excited at 310 nm, the S-CDs produced bright emission with a quantum yield of 7.15% at 397 nm. The S-CDs exhibited selective and sensitive quenching responses with limits of detection (LODs) of 4.25 μg mL-1 and 3.15 μg mL-1 for variable concentrations of Cr6+ and Fe3+, respectively, accompanied by a consistent linear relationship between fluorescence intensity and these concentrations. Fluorescence lifetime measurements were used to investigate the fluorescence quenching mechanism, which supports the static type of quenching. Outstanding benefits of the developed S-CD based fluorescence probe include its low cost, excellent sensitivity and selectivity, and ease of use for the detection of Cr6+ and Fe3+ ions. The developed carbon dot based fluorescent probe was successfully used to detect Cr6+ and Fe3+ ions in real water samples with an excellent recovery ratio.

Recyclable adsorption removal and fluorescent monitoring of hexavalent chromium by electrospun nanofibers membrane derived from Tb3+ coordinating polyarylene ether amidoxime

Emerging technologies or advanced materials which can simultaneously adsorb and detect highly toxic Cr(VI) are urgently in demand for environmental remediation. Herein, we have designed and synthesized a functional polyarylene ether with aromatic main chain and pendent carboxyl groups along with amidoxime group that can be coordinated with different metal ions. Thanks to its versatile activation of the lanthanide ions' inherent fluorescence and good processability, the fluorescent nanofiber membranes with competitive Cr(VI) adsorption and detection performance have been fabricated via one-step electrospinning of mixed solution containing synthesized polymer and terbium salt. More specifically, the optimized nanofiber membrane exhibits a maximal Cr(VI) adsorption of 278.2 mg/g and specific detection for hexavalent chromium down to 11.76 nM. More importantly, the prepared fluorescent nanofiber membranes can be easily re-generated and re-used for both Cr(VI) adsorption and detection for five times. Given the unique advantages of easy fabrication, competitive dual functionalities as well as good reusability of electrospun fluorescent nanofiber membranes, the present work basically opens up new insight in the design of multifunctional recyclable material for the remediation of heavy metal pollution.

Ultrathin porous Pd metallene as highly efficient oxidase mimics for the colorimetric detection of chromium (VI)

Palladium (Pd)-based nanomaterials are the emerging class of catalysts with individual physiochemical properties. Unlike traditional catalysts, metallenes showed abundant active sites, large surface area, and high atomic utilization. Based on these benefits, we demonstrate a highly active 2D graphene-like Pd metallene with abundant accessible active sites serving as a highly efficient oxidase mimic. The structure and morphology of Pd metallenezymes were controlled to enhance the catalytic performance and to efficiently utilize all the Pd atoms. Pd metallenezymes with excellent oxidase-like activity were successfully applied for colorimetric-based chromium (VI) (Cr(VI)) detection in a real environment. 3,3',5,5'-Tetramethylbenzidine (TMB) was used as a typical chromogenic substrate catalyzed by Pd metallene to show that blue oxidized TMB (ox TMB) was significantly reduced to colorless TMB by the reducing agent 8-hydroxyquinoline (8-HQ). The reaction process was impressively reversed by the addition of Cr(VI), which interacted with 8-HQ to restore the blue color of TMB. Based on the above results, a facile and effective colorimetric sensing system for the detection of Cr(VI) with a low detection limit of 2.8 nM was developed and could be successfully applied to the detection of Cr(VI) in a real environment.

Photo-enhanced electrochemical and colorimetric dual-modal aptasensing for aflatoxin B1 detection based on graphene-gold Schottky contact

A photo-enhanced electrochemical (PEEC) and colorimetric (CM) dual-modal aptasensor was developed with rGO-AuNP Schottky contact for AFB1 monitoring. The PEEC mode allowed the ultrasensitive quantitation based on the photo-enhanced electroactivity mechanism, while the CM mode offered a rapid threshold-level qualitative assay with a portable colorimeter.

Facile preparation of bimetallic Au-Cu nanoclusters as fluorescent nanoprobes for sensitive detection of Cr3+ and S2O82- ions

Metallic nanoclusters (NCs) have attracted special attention from researchers due to their interesting optical properties. In this experiment, we proposed a facile one-step method for the synthesis of bimetallic gold-copper nanoclusters (AuCuNCs). The prepared AuCuNCs were characterized by fluorescence spectroscopy (FL), UV-vis absorption spectrum, transmission electron microscopy (TEM), etc. The emission peak of the prepared AuCuNCs was located at 455 nm and showed blue luminescence under the excitation of 365 nm UV light. Furthermore, after the addition of Cr³⁺ and S₂O₈^2- ions, the FL emission intensity of AuCuNCs was significantly reduced at 455 nm and there was a color change of diminished blue luminescence under UV lamp. The AuCuNCs exhibited excellent linearity and sensitivity for the detection of Cr³⁺ and S₂O₈^2- ions. The limits of detection (LOD) for the Cr³⁺ and S₂O₈^2- ions were calculated to be 1.5 and 0.037 μM, respectively. Finally, the recoveries of Cr³⁺ and S₂O₈^2- ions in Runxi Lake and tap water were measured by standard addition recovery test and were 96.66 ∼ 116.29 %, 95.75 ∼ 119.4 %.

BSA-stabilized silver nanoclusters for efficient photoresponsive colorimetric detection of chromium(VI)

Hexavalent chromium is a highly toxic substance, which will pose a serious threat to human life and health and the entire ecosystem. Therefore, it is crucial to establish a simple and rapid detection method for hexavalent chromium. In this work, we fabricated bovine serum albumin-stabilized silver nanocluster (BSA-Ag₁₃ NC) which exhibited photoresponsive oxidase-like activity, catalyzing the oxidation of colorless 3,3',5,5'-tetramethylbenzidine (TMB) to the blue oxidized state TMB (oxTMB) in a short time. Interestingly, 8-hydroxyquinoline (8-HQ) can significantly inhibit the color reaction of TMB oxidation while Cr(VI) can interact specifically with 8-HQ to restore this chromogenic reaction. Based on the above facts, a colorimetric sensing system for detecting Cr(VI) was developed. The sensing system shows a wide linear range, and good selectivity, with a low detection limit of 2.32 nM. Moreover, this sensing system could be successfully applied to the detection of Cr(VI) in lake water, tap water, and sewage with satisfactory results.

Thionine-mediated electrocatalytic reduction for electrochemical detection of EDTA-Fe(III) in soy sauce

Electrocatalytic reactions based on electron transfer mediators provide a simple and effective route for the development of convenient and sensitive electrochemical assays. Here, we report a novel electrocatalytic assay for detection of EDTA-Fe(III), which is widely used as a supplement in iron-fortified foods to reduce prevalence of iron deficiency. Unlike conventional electrochemical methods to detect Fe(III) ion, signaling mechanism of our electrocatalytic assay relies on the previously unexplored thionine-mediated electrochemical reduction of EDTA-Fe(III). This electrocatalytic detection method is sensitive for EDTA-Fe(III) detection in the linear concentration range from 10 to 750 μM with a detection limit of 2.5 μM. It is also specific enough and applicable to detection of EDTA-Fe(III) in real soy sauce samples with satisfactory recovery. The one-step electrocatalytic reduction for signal generation enables the direct and sensitive electrochemical detection of EDTA-Fe(III). We believe that this electrocatalytic assay can serve as a general platform for quantification of EDTA-Fe(III) in many EDTA-Fe(III)-fortified foods. And because thionine is increasingly used as a signal reporter in electrochemical DNA/aptamer sensors, the engineered electrocatalytic reaction of thionine-mediated electrochemical reduction of EDTA-Fe(III) will also provide a simple signal amplification means for the development of highly sensitive electrochemical biosensors.

Raspberry-Like Gold Nanoparticles Based On Nanoclusters Anchored on Cyclodextrin-Functionalized Nanoparticles: Synthesis and Ultrasensitive Electrochemical Detection of Chromium(VI) Ions

A facile synthetic strategy is devised to construct raspberry like gold nanoparticles (RbNPs) formed by gold nanoclusters wrapped around β-cyclodextrin functionalized gold nanoparticles (CD-AuNPs@AuNCs). An efficient and sensitive electrochemical sensor for the detection of Cr(VI) has been developed based on RbNPs. The sensing platform exhibits an excellent wide linear range (100 pg mL^-1 to 10 μg mL^-1 ), extremely low detection limit (40.91 fg mL^-1 i. e. 0.79 pM), which may pave a new way to fabricate other ultrasensitive electrochemical sensors based on the designed RbNPs.

Threonine Phosphorylation of an Electrochemical Peptide-Based Sensor to Achieve Improved Uranyl Ion Binding Affinity

We have successfully designed a uranyl ion (U(VI)-specific peptide and used it in the fabrication of an electrochemical sensor. The 12-amino acid peptide sequence, (n) DKDGDGYIpTAAE (c), originates from calmodulin, a Ca(II)-binding protein, and contains a phosphothreonine that enhances the sequence's affinity for U(VI) over Ca(II). The sensing mechanism of this U(VI) sensor is similar to other electrochemical peptide-based sensors, which relies on the change in the flexibility of the peptide probe upon interacting with the target. The sensor was systematically characterized using alternating current voltammetry (ACV) and cyclic voltammetry. Its limit of detection was 50 nM, which is lower than the United States Environmental Protection Agency maximum contaminant level for uranium. The signal saturation time was ~40 min. In addition, it showed minimal cross-reactivity when tested against nine different metal ions, including Ca(II), Mg(II), Pb(II), Hg(II), Cu(II), Fe(II), Zn(II), Cd(II), and Cr(VI). Its reusability and ability to function in diluted aquifer and drinking water samples were further confirmed and validated. The response of the sensor fabricated with the same peptide sequence but with a nonphosphorylated threonine was also analyzed, substantiating the positive effects of threonine phosphorylation on U(VI) binding. This study places emphasis on strategic utilization of non-standard amino acids in the design of metal ion-chelating peptides, which will further diversify the types of peptide recognition elements available for metal ion sensing applications.

Ecological effects, remediation, distribution, and sensing techniques of chromium

Chromium is detected in most ecosystems due to the increased anthropogenic activities in addition to that developed from natural pollution. Chromium contamination in the food chain results due to its persistent and non-degradable nature. The release of chromium in the ecosystem accretes and thereafter impacts different life forms, including humans, aquatic and terrestrial organisms. Leaching of chromium into the ground and surface water triggers several health ailments, such as dermatitis, eczematous skin, allergic reactions, mucous and skin membrane ulcerations, allergic asthmatic reactions, bronchial carcinoma and gastroenteritis. Physiological and biological treatments for the removal of chromium have been discussed in depth in the present communication. Adsorption and biological treatment methods are proven to be alternatives to chemical removal techniques in terms of cost-effectiveness and low sludge formation. Chromium sensing is an alternative approach for regular monitoring of chromium in different water bodies. This review intended to explore different classes of sensors for chromium monitoring. However, the spectrochemical methods are more sensitive in chromium ions sensing than electrochemical methods. Future study should focus on miniaturization for portability and on-site measurements without requiring a large instrument provides a good aspect for future research.

Microwave-assisted synthesis of nitrogen-doped carbon dots using prickly pear as the carbon source and its application as a highly selective sensor for Cr(VI) and as a patterning agent

Preparation of water-dispersible carbon dots from inexpensive natural carbon precursors and its application for purposes such as sensing, bio-imaging and patterning agents is showing growing interest in recent years. In this study, we have reported the preparation of nitrogen-doped carbon dots (N-CDs) using prickly pear as the carbon source and m-xylylenediamine as the nitrogen source using a one-step microwave-assisted synthetic process. The N-CDs prepared were characterized on the basis of elemental analysis, XPS, powder-XRD, FT-IR, Raman, TEM, UV-vis and fluorescence spectroscopy. Doping of nitrogen in the N-CDs made them highly fluorescent and the study on their ion-recognition property revealed that they detect highly toxic Cr(VI) with high selectivity and sensitivity (LOD, 0.04 μM) and without interference from the other ions used in this study. By immobilizing these N-CDs onto filter paper, sensor strips were prepared for on-site monitoring/field applications and they were successfully used for the detection of Cr(VI) in water. Detailed spectral analysis revealed that the mechanism of Cr(VI) sensing involved a phenomenon called the "inner filter effect" and analysis of the fluorescence lifetime data suggested the "static quenching" of fluorescence intensity. These N-CDs were used to prepare fluorescent carbon ink and were successfully used as patterning agents.

One pot synthesis and self-assembly of methylene blue-backboned polymers

Studies of methylene blue-backboned polymers (MBPs) are hindered by the limited availability of polymerization methods. Herein, we developed an oxidative polymerization method to produce MBPs. The polymerization is performed in aqueous medium, and is organic solvent-free, heavy metal-free, time-efficient (on a timescale of minutes), and does not need pre-formed methylene blue chromophores. The effects of the alkyl chains of the MBPs on the photophysical properties and self-assembly behavior (e.g., vesicles and nanorings) are significant, which highlights the possibility of controlling the MBP properties via rationally tailoring the functionality of the MBP monomers prior to polymerization. Importantly, the self-assembly structures can be predicted using the dissipative particle dynamics (DPD) simulation method.

p-Co-BDC/AuNPs-based multiple signal amplification for ultra-sensitive electrochemical determination of miRNAs

In this work, we report AuNPs-decorated pyrolyzed Co-BDC nanosheets (p-Co-BDC/AuNPs) as high-performance electrocatalyst for developing an electrochemical platform. p-Co-BDC/AuNPs as a new electrocatalyst showed superior electrocatalytic activity towards the electrochemical oxidation of methylene blue (MB). Besides, magnetic p-Co-BDC/AuNPs can be well immobilized on the magnetic glassy carbon electrode without further assistance. The oxidation of MB can be reduced by ascorbic acid. Inspired by this phenomenon, an electrochemical biosensor was constructed based on multiple signal amplification for the diagnosis of miRNAs. Firstly, p-Co-BDC/AuNPs enhanced the electrochemical oxidation of MB. Then, strand displacement amplification reaction can form lots of double helix structure DNA to embed more MB molecules. Finally, ascorbic acid in the electrolyte was utilized to reduce the oxidation of MB and improve the electrochemical signal of MB electro-oxidation. The linear detection range for the detection of miRNAs is 100 aM to 10 nM, and the limit of detection is 86 aM. Furthermore, the constructed biosensor also displayed satisfactory selectivity, good reproducibility, and excellent recovery in the detection of real samples. We are convinced that our proposed multiple signal amplification strategy will provide more promising methods for the diagnosis of cancer.

Recyclable Functionalized Material for Sensitive Detection and Exceptional Sorption of Hexavalent Chromium and Permanganate Ions with Biosensing Applications

Environmental remediation with a single platform for selective sensing and removal of toxic analytes with recyclability of the material has always been a desirable system for sustainability. However, materials comprising all the abovementioned advantages are rarely known for oxoanions. We herein developed a fluorogenic napthalimide-based functionalized mesoporous silica material (SiO₂@NBDBIA) as a signaling and remediation system for oxoanions (CrO₄^2-, Cr₂O₇^2-, and MnO₄^-) from a pool of several anions. The fluorescence quenching of the SiO₂@NBDBIA material in the presence of CrO₄^2-, Cr₂O₇^2-, and MnO₄^- ions gives the limit of detection (LOD) values of 6.23, 25.2, and 20.32 ppb, respectively, which are well below the maximum contaminant level demarcated by the United States Environmental Protection Agency. The maximum adsorption capacities of the material for the abovementioned oxoanions are found to be 352, 363, and 330 mg/g, respectively, which are well above those mentioned in the literature reports. Contrary to the literature-dominated irreversible ion-exchange mechanism, the reversible hydrogen-bonded binding of the material with the oxoanions leads to the recyclability of the material easily, which is very rare in the literature. The DFT calculations were performed to examine the interactions between the material and oxoanions. For real applications, this material was also used as a fluorescence probe to detect these oxoanions in the actual water samples, and more interestingly, used as a biosensing probe for these oxoanions in the living organism Artemia salina through fluorescence imaging. Thus, the SiO₂@NBDBIA material is a unique example of recyclable material for detecting and remediating oxoanions.

Fluorescent carbon dots embedded in mesoporous silica nanospheres: A simple platform for Cr(VI) detection in environmental water

In this work, amino-functionalized mesoporous silica nanospheres (NH₂-mSiO₂) anchored with carbon dots (CDs) have been designed to construct an outstanding fluorescent sensor for heavy metal detection. Uniform mSiO₂ was chosen to provide an optically transparent scaffold for immobilizing CDs. With the help of amino group modification on the surface of silica, benzene-1,4-diboronic acid (BA) was used as raw material to load CDs in the pores of mSiO₂ by one-step solvothermal method. The proposed nanohybrid can solve the problem of aggregation-induced fluorescence quenching, leading to bright blue emission at 450 nm. Meanwhile, the fluorescence of NH₂-mSiO₂@CDs showed high sensitivity to Cr(VI) in acetic acid buffer solution (pH = 4) with detection limit as low as 5 nM by inner filter effect (IFE) and electrostatic interaction (EI). The proposed method can also be extended to other CDs-based detection systems for chemical/biological sensors.

Electrochemical detection of heavy metal ions in water

Heavy metal ions are one of the main sources of water pollution. Most heavy metal ions are carcinogens that pose a threat to both ecological balance and human health. With the increasing demand for heavy metal detection, electrochemical detection is favorable due to its high sensitivity and efficiency. Here, after discussing the pollution sources and toxicities of Hg(ii), Cd(ii), As(iii), Pb(ii), UO₂(ii), Tl(i), Cr(vi), Ag(i), and Cu(ii), we review a variety of recent electrochemical methods for detecting heavy metal ions. Compared with traditional methods, electrochemical methods are portable, fast, and cost-effective, and they can be adapted to various on-site inspection sites. Our review shows that the electrochemical detection of heavy metal ions is a very promising strategy that has attracted widespread attention and can be applied in agriculture, life science, clinical diagnosis, and analysis.

Carbon dots derived from Poria cocos polysaccharide as an effective “on-off” fluorescence sensor for chromium (VI) detection

Chromium is a harmful contaminant showing mutagenicity and carcinogenicity. Therefore, detection of chromium requires the development of low-cost and high-sensitivity sensors. Herein, blue-fluorescent carbon quantum dots were synthesized by one-step hydrothermal method from alkali-soluble Poria cocos polysaccharide, which is green source, cheap and easy to obtain, and has no pharmacological activity due to low water solubility. These carbon quantum dots exhibit good fluorescence stability, water solubility, anti-interference and low cytotoxicity, and can be specifically combined with the detection of Cr(VI) to form a non-fluorescent complex that causes fluorescence quenching, so they can be used as a label-free nanosensor. High-sensitivity detection of Cr(VI) was achieved through internal filtering and static quenching effects. The fluorescence quenching degree of carbon dots fluorescent probe showed a good linear relationship with Cr(VI) concentration in the range of 1–100 μM. The linear equation was F₀/F = 0.9942 + 0.01472 [Cr(VI)] (R² = 0.9922), and the detection limit can be as low as 0.25 μM (S/N = 3), which has been successfully applied to Cr(VI) detection in actual water samples herein.

•

Carbon dots was synthesized from alkaloid-soluble Poria cocos polysaccharide, which used for Cr (VI) detection.

•

High sensitivity and selectivity detection of Cr(VI) based on internal filtering effect and static quenching mechanism.

•

The method analysis speed is quick, sensitive, raw materials for convenient, inexpensive.

•

The method has been applied to the determination of Cr(VI) in actual samples with satisfactory recovery.

Remote Investigation of Total Chromium Determination in Environmental Samples of the Kombolcha Industrial Zone, Ethiopia, Using Microfluidic Paper-based Analytical Devices

Microfluidic paper-based analytical devices (μ-PADs) fabricated in Japan were employed for the determination of total chromium (Cr) in water, soil, and lettuce irrigated with wastewater in Ethiopia. The μ-PADs, which were printed by wax printing in Japan, were transported to Ethiopia and prepared for the determination of total Cr by adding appropriate reagents to the pretreatment and detection zones. Soil and lettuce samples were determined by the μ-PADs and a UV-Vis spectrophotometer in Ethiopia. A paired t-test showed that the mean total Cr concentrations determined in the soil and lettuce samples were not significantly different between μ-PADs and UV-Vis spectrophotometric analysis at the 5% level of significance. This implies that the μ-PADs have good accuracy and reliability, and could be employed to monitor Cr in environmental samples. We found that the total Cr concentrations in all soil and lettuce samples were above the permissible limit. Moreover, evaluating Cr contamination level using the geo-accumulation index indicated that the soils were contaminated with Cr moderately to heavily. Thus, the present work successfully demonstrated the potential of remote investigations of pollution in a less-equipped laboratory by transporting the μ-PADs fabricated in another laboratory.

Speciation of chromium in water samples using microfluidic paper-based analytical devices with online oxidation of trivalent chromium

Speciation of chromium (Cr) was demonstrated using microfluidic paper-based analytical devices (μ-PADs) that permit the colorimetric determination of hexavalent chromium (Cr(VI)) and trivalent chromium (Cr(III)) via online oxidation. The μ-PADs consist of left and right channels that allow the simultaneous measurements of Cr(VI) and total Cr based on the colorimetric reaction of Cr(VI) with 1,5-diphenylcarbazide (DPC). For the determination of Cr(VI), a sample solution was directly reacted with DPC in the left channels whereas total Cr was determined in the right channels, which permitted online oxidation in the pretreatment zone containing cerium (IV) (Ce(IV)) followed by a colorimetric reaction with DPC. We found that the online oxidation of Cr(III) proceeded 100% whereas Ce(IV) inhibited the reaction of Cr(VI) with DPC. Therefore, speciation can be achieved by measuring the Cr(VI) and total Cr in the left and right channels followed by the subtraction of Cr(VI) from total Cr. The limits of detection and quantification were 0.008 and 0.02 mg L^-1 for Cr(VI) and 0.07 and 0.1 mg L^-1 for Cr(III) or total Cr, respectively. The linear dynamic ranges were 0.02-100 mg L^-1 and 0.1-60 mg L^-1 for Cr(VI) and Cr(III), respectively. The RSDs were less than 7.5%. The results obtained using μ-PADs were in good agreement with those obtained via ICP-OES with recoveries of 92-108% for Cr(III) and 108-110% for Cr (VI) using μ-PADs, and 106-110% for total Cr using ICP-OES. Thus, the μ-PADs could potentially be utilized for the speciation of chromium in developing countries where environmental pollution and the availability of sophisticated instruments are significant problems.

Electrochemical reduction of Cr(VI) in water: lessons learned from fundamental studies and applications

Converting toxic Cr(vi) to benign Cr(iii) would offer a solution to decontaminate drinking water. Electrochemical methods are ideally suited to carry out this reduction without added external reductants. Achieving this transformation at low overpotentials requires mediating the transfer of protons and electrons to Cr(vi). In this review thermodynamic parameters will be discussed to understand Cr(vi) speciation in water and identify reduction pathways. The electrochemical reduction of Cr(vi) at bare electrodes is reviewed and mechanistic considerations are discussed. Works on modified electrodes are compared to identify key parameters influencing the reduction. An overview of current applications to Cr(vi) reduction is briefly discussed to link fundamental studies to applications.

Electrocatalytic Mechanism for Improving Sensitivity and Specificity of Electrochemical Nucleic Acid-Based Sensors with Covalent Redox Tags-Part I

The design and development of advanced electrocatalysis have been extensively explored for efficient energy conversion and electrochemical biosensing. Both ferricyanide (Fe(CN)₆^3-) and methylene blue (MB) have been widely used in the development of electrochemical biosensing strategies. However, the electrocatalytic mechanism between nucleic acid-tethered MB and Fe(CN)₆^3- remains unexplored. In this manuscript, we aim to provide readers in our community molecular insights into the electrocatalytic mechanism. The exploration of the electrocatalytic mechanism starts with a kinetic zone diagram for a one-electron homogeneous electrocatalytic reaction. Two factors-the excess factor γ and the kinetic parameter λ-are important for a homogeneous electrocatalytic reaction; as such, we studied both. The excess factor parameter was controlled by applying Fe(CN)₆^3- with various concentrations (50, 100, and 200 μM), and the kinetic parameter effect on the electrocatalytic process was examined by varying scan rates of cyclic voltammetry (CV) or frequencies of square-wave voltammetry (SWV). Moreover, we discovered that the probe dynamics of the nucleic acid tether is the third rate-limiting factor for the electrocatalytic reaction. As the probe dynamics switch of electrode-bound nucleic acid is often utilized as a mechanism in electrochemical nucleic acid-based sensors, we believe the electrocatalysis between nucleic acid-tethered MB and Fe(CN)₆^3- is capable of enhancing sensitivity and specificity of electrochemical nucleic acid-based sensors with covalent redox tags.

Colorimetric detection of Cr6+ ions based on surface plasma resonance using the catalytic etching of gold nano-double cone @ silver nanorods

Hexavalent chromium ion (Cr⁶⁺) is highly toxic to human health and environment. Herein, high-performance detection of Cr⁶⁺ is of great import. In this study, a rapid and sensitive multicolor colorimetric method for detection of Cr⁶⁺ in aqueous solution was established on the basis of Cr⁶⁺ etching of gold nano-double cone@silver nanorods (Au NDC@Ag NRs). Au NDC@Ag NRs was synthesized by a modified seed-mediated growth method. The catalytic etching induced by Cr⁶⁺ changed the morphology of Au NDC@Ag NRs, leading to the attenuation of surface plasma resonance (SPR) and the redshift of absorption spectra. Meanwhile, Au NDC@Ag NRs exhibits obvious color changes from orange to pink, to purple, and finally becomes colorless with the increasing concentrations of Cr⁶⁺. With such a design, naked-eye detection of Cr⁶⁺ was realized with high sensitivity. The proposed multicolor sensing method showed a good linearity between the redshift change of absorption peak (△λ) and the concentrations of Cr⁶⁺ in the range from 2.5 to 40 μM. The limit of detection (LOD) was calculated as 1.69 μM in aqueous solution. In addition, successful detection of Cr⁶⁺ in tap water and Yangtze River water, indicating the real applications of Au NDC@Ag NRs probe in monitoring Cr⁶⁺ in environment.

Biologically inspired catalyst for electrochemical reduction of hazardous hexavalent chromium

An indirect electrochemical detoxification and detection platform has been demonstrated for toxic hexavalent chromium (Cr(vi)) based on the biologically important N-4 macrocycle. The research work describes a simple, green, low-cost and potential way for the synthesis of a new N-4 macrocyclic molecule and the molecule is characterized by various analytical and spectroscopic techniques like elemental analysis, TGA, FT-IR, UV-visible, mass spectrometry and NMR spectroscopies, and cyclic voltammetry. The synthesized molecule was explored for the electrochemical reduction of Cr(vi) using both voltammetric and amperometric methods. Amperometric studies exhibited 50 to 2500 nM linear range and the detection limit and quantification limit are 18 and 50 nM, respectively. The common coexisting metal ions did not interfere with Cr(vi) even in the presence of 40-fold excess interfering ions. The real sample analysis was carried out with the fabricated sensor and successfully quantified a recovery result (98-104%) of Cr(vi) in water. This proposed sensor is helpful in the detection of chromium ions in drinking water and is capable of detecting Cr(vi) in the limits set by the World Health Organization (WHO). In addition, this sensor satisfactorily demonstrated considerable stability and reproducibility.

Recent Advances in Electrochemical Monitoring of Chromium

The extensive use of chromium by several industries conducts to the discharge of an immense quantity of its various forms in the environment which affects drastically the ecological and biological lives especially in the case of hexavalent chromium. Electrochemical sensors and biosensors are useful devices for chromium determination. In the last five years, several sensors based on the modification of electrode surface by different nanomaterials (fluorine tin oxide, titanium dioxide, carbon nanomaterials, metallic nanoparticles and nanocomposite) and biosensors with different biorecognition elements (microbial fuel cell, bacteria, enzyme, DNA) were employed for chromium monitoring. Herein, recent advances related to the use of electrochemical approaches for measurement of trivalent and hexavalent chromium from 2015 to 2020 are reported. A discussion of both chromium species detections and speciation studies is provided.

Polyoxometalate-based crystalline materials as a highly sensitive electrochemical sensor for detecting trace Cr(vi)

It is crucial to find a convenient and sensitive method for quantitative determination of heavy metal chromium(vi) ions. Developing crystalline materials coupled with polyoxometalates as an electrochemical sensor is a promising approach to address the above issues. Here we reported two reductive polyoxometalate-based crystalline compounds with the formula of (H2bpp)2[Na4Fe(H2O)7][Fe(P4Mo6O31H6)2]·2H2O (1) and (H2bpp)6(bpp)2[Fe(P4Mo6O31H8)2]2·13H2O (2) (bpp = 1,3-bi(4-pyridyl)propane). Structural analysis indicated that both two compounds were composed of inorganic polyanionic clusters and organic protonated bpp cations. The difference lies in the arrangement mode of the inorganic moiety: crystal 1 shows a unique three-dimensional (3-D) inorganic porous skeleton, while crystal 2 consists of isolated 0-D polyanionic clusters. When used as electrochemical sensors in the determination of trace Cr(vi), crystal 1 shows a broad linearity range (2-2610 μM) with a low limit of detection (LOD) of 0.174 μM (9 ppb), which is superior to that of compound 2 (a LOD of 0.33 μM) and meets the standard of Cr(vi) in drinking water set by the WHO (less than 0.962 μM or 50 ppb). Importantly, crystal 1 showed benign selectivity to Cr(vi) in the presence of various heavy metal ions and good reproducibility in a real water sample, which prove its strong anti-interference ability. In addition, experimental results showed that the spatial arrangement of polyanionic clusters could affect the final electrochemical behavior of crystalline materials. This work provides some insights into the design of cost-effective POM-based electrochemical sensors at the molecular level.

Polyethylenimine-stabilized silver nanoclusters act as an oxidoreductase mimic for colorimetric determination of chromium(VI)

A new and efficient assay is proposed for the photometric determination of Cr⁶⁺ by employing polyethylenimine-stabilized Ag nanoclusters (PEI-AgNCs) as an oxidoreductase mimic. Cr⁶⁺ with certain oxidicability is able to specifically react with 3,3',5,5'-tetramethylbenzidine (TMB), giving a color change from colorless to blue indicating the presence of Cr⁶⁺. However, the redox kinetics is so slow that the sensitivity obtained for Cr⁶⁺ determination is very poor. It is interestingly found that PEI-AgNCs can act as an oxidoreductase-like nanozyme to significantly promote the sluggish reaction, making it possible to rapidly detect toxic Cr⁶⁺ with remarkably enhanced performance. With the use of PEI-AgNCs, fast and convenient determination of Cr⁶⁺ was realized, with a limit of detection as low as 1.1 μM. Additionally, the proposed assay exhibited excellent selectivity; other ions, including Cr³⁺, hardly affected the determination of Cr⁶⁺. Graphical abstract Polyethylenimine-stabilized silver nanoclusters (PEI-AgNCs) act as an oxidoreductase mimic to catalyze the redox reaction of Cr⁶⁺ and 3,3',5,5'-tetramethylbenzidine (TMB), enabling the high-performance colorimetric determination of toxic Cr⁶⁺.

Efficient Visual Chemosensor for Hexavalent Chromium via a Controlled Strategy for Signal Amplification in Water

Generally, 3,3',5,5'-tetramethylbenzidine (TMB) cannot react with hydrogen peroxide (H₂O₂) in neutral pH or in water at room temperature and pressure. Herein, we found that hexavalent chromium (Cr⁶⁺) can trigger TMB reacting with H₂O₂ (TMB-H₂O₂) in ultrapure water along with a weak signal output. Then, to implement signal amplification effectively, we designed a ternary nanohybrid material containing graphene oxide (GO) nanosheets, gold nanoparticles (Au NPs), and hyperbranched polyethylenimine (PEI) to form rGO/PEI/Au nanohybrids via chemical bonding. After addition of a trace amount of Cr⁶⁺, rGO/PEI/Au nanohybrids can effectively catalyze TMB-H₂O₂ in ultrapure water; thus, a visual chemosensor and electronic spectrum quantitative analysis method for Cr⁶⁺ based on chromium-stimulated peroxidase mimetic activity of rGO/PEI/Au nanohybrids were established. The visual chemosensor exhibits excellent selectivity and interference immunity against 34 other interfering substances with a detection limit as low as 2.14 nM. The visual chemosensor for Cr⁶⁺ with a low detection limit and high selectivity is expected to have a potential application in environmental analysis, monitoring, and human health maintenance.

Ultrahigh Selective Colorimetric Quantification of Chromium(VI) Ions Based on Gold Amalgam Catalyst Oxidoreductase-like Activity in Water

Hexavalent chromium ion (Cr⁶⁺) is one of the most toxic substances for plants, for animals, and is a confirmed human respiratory carcinogen. However, so far, there are few independent and efficient colorimetric methods for detection of Cr⁶⁺. Here, we introduce a convenient, label-free, catalysis-based, and efficient strategy for quantification of Cr⁶⁺ by using a colorimetric sensing probe 3,3',5,5'-tetramethylbenzidine (TMB). In the presence of a trace amount of gold amalgam nanocomposites (Au@Hg) and Cr⁶⁺, TMB can be oxidized to oxTMB and the color changed to an intense blue that was observed by naked-eye and absorption spectroscopic method. In addition, the colorimetric method shows the high selectivity against 34 other interfering substances, and it can be performed at room temperature, in water, and requires only ∼5 min. Thus, the catalysis-based colorimetric assay for accurate and ultrahigh selective identification of Cr⁶⁺ will find widespread use in the world.

Ratiometric fluorescent detection of chromium(VI) in real samples based on dual emissive carbon dots

As we know, hexavalent chromium (Cr(VI)) was usually used as an additive to improve the color fastness during the printing and dyeing process, and thus posing tremendous threat to our health and living quality. In this work, the dual emissive carbon dots (DECDs) were synthesized through hydrothermal treatment of m-aminophenol and oxalic acid. The obtained DECDs not only exhibited dual emission fluorescence peaks (430 nm, 510 nm) under the single excitation wavelength of 380 nm, but also possessed good water solubility and excellent fluorescence stability. A ratiometric fluorescent method for the determination of Cr(VI) was developed using the DECDs as a probe. Under the optimal conditions, a linear range was obtained from 2 to 300 μM with a limit of detection of 0.4 μM. Furthermore, the proposed ratiometric fluorescent method was applied to the analysis of Cr(VI) in textile, steel, industrial wastewater and chromium residue samples with satisfactory recoveries (88.4-106.8%).

Preparation of polyacrylonitrile nanofibers decorated by N-doped carbon quantum dots: application as a fluorescence probe for determination of Cr(vi)

This study presents a new method to synthesize a fluorescence probe using an N-doped carbon quantum dot decorated polyacrylonitrile nanofiber (N-CQD@NF) nanocomposite.

Biosensor for detection of dissolved chromium in potable water: A review

The unprecedented deterioration rate of the environmental quality due to rapid urbanization and industrialization causes a severe global health concern to both ecosystem and humanity. Heavy metals are ubiquitous in nature and being used extensively in industrial processes, the exposure to excessive levels could alter the biochemical cycles of living systems. Hence the environmental monitoring through rapid and specific detection of heavy metal contamination in potable water is of paramount importance. Various standard analytical techniques and sensors are used for the detection of heavy metals include spectroscopy and chromatographic methods along with electrochemical, optical waveguide and polymer based sensors. However, the mentioned techniques lack the point of care application as it demands huge capital cost as well as the attention of expert personnel for sample preparation and operation. Recent advancements in the synergetic interaction among biotechnology and microelectronics have advocated the biosensor technology for a wide array of applications due to its characteristic features of sensitivity and selectivity. This review paper has outlined the overview of chromium toxicity, conventional analytical techniques along with a particular emphasis on electrochemical based biosensors for chromium detection in potable water. This article emphasized porous silicon as a host material for enzyme immobilization and elaborated the working principle, mechanism, kinetics of an enzyme-based biosensor for chromium detection. The significant characteristics such as pore size, thickness, and porosity make the porous silicon suitable for enzyme entrapment. Further, several schemes on porous silicon-based immobilized enzyme biosensors for the detection of chromium in potable water are proposed.

Folding- and Dynamics-Based Electrochemical DNA Sensors

A number of electrochemical DNA sensors based on the target-induced change in the conformation and/or flexibility of surface-bound oligonucleotides have been developed in recent years. These sensors, which are often termed E-DNA sensors, are comprised of an oligonucleotide probe modified with a redox label (e.g., methylene blue) at one terminus and attached to a gold electrode via a thiol-gold bond at the other. Binding of the target to the DNA probe changes its structure and dynamics, which, in turn, influences the efficiency of electron transfer to the interrogating electrode. Since electrochemically active contaminants are less common, these sensors are resistant to false-positive signals arising from the nonspecific adsorption of contaminants and perform well even when employed directly in serum, whole blood, and other realistically complex sample matrices. Moreover, because all of the sensor components are chemisorbed to the electrode, the E-DNA sensors are essentially label-free and readily reusable. To date, these sensors have achieved state-of-the-art sensitivity, while offering the unprecedented selectivity, reusability, and the operational convenience of direct electrochemical detection. This chapter reviews the recent advances in the development of both "signal-off" and "signal-on" E-DNA sensors. Critical aspects that dictate the stability and performance of these sensors are also addressed so as to provide a realistic overview of this oligonucleotide detection platform.

On–off–on fluorescent oligomer as a chemosensor for the detection of manganese(vii), sulfur(ii) and aldehydes based on the inner filter effect

In this article, a sensitive and selective on–off–on fluorescence chemosensor, Tyloxapol (one kind of water soluble oligomer), was developed for the label-free detection of MnO₄⁻ ions in aqueous solution.