Electrochemical Detection of Dopamine and Serotonin in the Presence of Interferences in a Rotating Droplet System

Simultaneous Electrochemical Detection of Dopamine and Tryptophan Using 3D Goethite-Spongin Composites

In this study, a facile approach for simultaneous determination of dopamine (DA) and tryptophan (TRP) using a 3D goethite-spongin-modified carbon paste electrode is reported. The prepared electrode exhibited excellent electrochemical catalytic activity towards DA and TRP oxidation. The electrochemical sensing of the modified electrode was investigated using cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy. Through differential pulse voltammetry analysis, two well-separated oxidation peaks were observed at 28 and 77 mV, corresponding to the oxidation of DA and TRP at the working electrode, with a large peak separation of up to 490 mV. DA and TRP were determined both individually and simultaneously in their dualistic mixture. As a result, the anodic peak currents and the concentrations of DA and TRP were found to exhibit linearity within the ranges of 4-246 μM for DA and 2 to 150 μM for TRP. The detection limits (S/N = 3) as low as 1.9 μM and 0.37 μM were achieved for DA and TRP, respectively. The proposed sensor was successfully applied to the simultaneous determination of DA and TRP in human urine samples with satisfactory recoveries (101% to 116%).

Facile Synthesis of Fe-Doped, Algae Residue-Derived Carbon Aerogels for Electrochemical Dopamine Biosensors

An abnormal level of dopamine (DA), a kind of neurotransmitter, correlates with a series of diseases, including Parkinson's disease, Willis-Ekbom disease, attention deficit hyperactivity disorder, and schizophrenia. Hence, it is imperative to achieve a precise, rapid detection method in clinical medicine. In this study, we synthesized nanocomposite carbon aerogels (CAs) doped with iron and iron carbide, based on algae residue-derived biomass materials, using Fe(NO3)3 as the iron source. The modified glassy carbon electrode (GCE) for DA detection, denoted as CAs-Fe/GCE, was prepared through surface modification with this composite material. X-ray photoelectron spectroscopy and X-ray diffraction characterization confirmed the successful doping of iron into the as-prepared CAs. Additionally, the electrochemical behavior of DA on the modified electrode surface was investigated and the results demonstrate that the addition of the CAs-Fe promoted the electron transfer rate, thereby enhancing their sensing performance. The fabricated electrochemical DA biosensor exhibits an accurate detection of DA in the concentration within the range of 0.01~200 µM, with a detection limit of 0.0033 µM. Furthermore, the proposed biosensor is validated in real samples, showing its high applicability for the detection of DA in beverages.

Real-time selective detection of dopamine and serotonin at nanomolar concentration from complex in vitro systems

Electrochemical sensors provide means for real-time monitoring of neurotransmitter release events, which is a relatively easy process in simple electrolytes. However, this does not apply to in vitro environments. In cell culture media, competitively adsorbing molecules are present at concentrations up to 350 000-fold excess compared to the neurotransmitter-of-interest. Because detection of dopamine and serotonin requires direct adsorption of the analyte to electrode surface, a significant loss of sensitivity occurs when recording is performed in the in vitro environment. Despite these challenges, our single-walled carbon nanotube (SWCNT) sensor was capable of selectively measuring dopamine and serotonin from cell culture medium at nanomolar concentration in real-time. A primary midbrain culture was used to prove excellent biocompatibility of our SWCNT electrodes, which is a necessity for brain-on-a-chip models. Most importantly, our sensor was able to electrochemically record spontaneous transient activity from dopaminergic cell culture without altering the culture conditions, which has not been possible earlier. Drug discovery and development requires high-throughput screening of in vitro models, being hindered by the challenges in non-invasive characterization of complex neuronal models such as organoids. Our neurotransmitter sensors could be used for real-time monitoring of complex neuronal models, providing an alternative tool for their characterization non-invasively.

3,5-Dihydroxybenzoic Acid-Based Selective Dopamine Detection via Subsititution-Enhanced Kinetics Differences

The selective recognition of dopamine (DA) over other neurotransmitter analogues is difficult due to the similar molecular structure and chemical reactivity. In this study, substitution-regulated chemical reactivity of the sensing substrate is utilized to explore a novel DA detection probe with satisfying selectivity. As a case study, 3,5-dihydroxybenzoic acid (DHBA, carboxy-substituted resorcinol)-based probes have been explored for selective and ratiometric DA sensing. The carboxy substitution benefits the stabilization of the carbanion intermediate and the azamonardine product, which enhances the reaction kinetics and thermodynamics and subsequently facilitates selective DA recognition over other analogues and interferents. By exploring DHBA emission as the internal reference, ratiometric fluorescence variation is realized, which contributes to sensitive DA analysis. With the combination of logic gate and fluorometric analysis, DA detection in both low and high concentrations can be readily achieved. In addition, the DA analysis in biological samples and the enzymatic transformation of DA analogues in cerebrospinal fluid samples are achieved by the proposed DHBA probe.

Electrochemical Sensing of Dopamine Using Polypyrrole/Molybdenum Oxide Bilayer-Modified ITO Electrode

The electrochemical sensing of biomarkers has attracted more and more attention due to the advantages of electrochemical biosensors, including their ease of use, excellent accuracy, and small analyte volumes. Thus, the electrochemical sensing of biomarkers has a potential application in early disease diagnosis diagnosis. Dopamine neurotransmitters have a vital role in the transmission of nerve impulses. Here, the fabrication of a polypyrrole/molybdenum dioxide nanoparticle (MoO₃ NP)-modified ITO electrode based on a hydrothermal technique followed by electrochemical polymerization is reported. Several techniques were used to investigate the developed electrode's structure, morphology, and physical characteristics, including SEM, FTIR, EDX, N₂ adsorption, and Raman spectroscopy. The results imply the formation of tiny MoO₃ NPs with an average diameter of 29.01 nm. The developed electrode was used to determine low concentrations of dopamine neurotransmitters based on cyclic voltammetry and square wave voltammetry techniques. Furthermore, the developed electrode was used for monitoring dopamine in a human serum sample. The LOD for detecting dopamine by using MoO₃ NPs/ITO electrodes based on the SWV technique was around 2.2 nmol L^-1.

Combining a protein-targeting small molecule and a thiol-targeting small molecule for detecting a serum risk marker of liver tumor recurrence

This work proposes a novel bioassay designed to detect the 2B receptor of serotonin in serum samples, which can serve as a risk marker for cancer recurrence after surgical resection. Traditional methods for detecting this marker are often costly and time-consuming, requiring specialized reagents and equipment. The new bioassay is designed to enable direct and reagent-less detection of the 2B receptor in serum samples, without the need of antibodies or enzymes. The assay uses a small molecule ligand for the 2B receptor combined with a thiol-targeting fluorescent dye on a compact peptide-based molecular frame. This design allows for a rapid and specific readout of the fluorescent signal upon probe-protein interaction. In addition, the covalent biosensing process used in the assay allows for signal enhancement by electrochemical cross-linking of serum proteins. The bioassay was successfully used to detect the 2B receptor in serum samples from hepatocarcinoma patients, indicating its potential as a powerful tool for early cancer detection and monitoring.

Conformationally Flexible Dimeric-Serotonin-Based Sensitive and Selective Electrochemical Biosensing Strategy for Serotonin Recognition

A novel electrochemical sensor was constructed based on an enzyme-mediated physiological reaction between neurotransmitter serotonin per-oxidation to reconstruct dual-molecule 4,4'-dimeric-serotonin self-assembled derivative, and the potential biomedical application of the multi-functional nano-platform was explored. Serotonin accelerated the catalytic activity to form a dual molecule at the C4 position and created phenolic radical-radical coupling intermediates in a peroxidase reaction system. Here, 4,4' dimeric-serotonin possessed the capability to recognize intermolecular interactions between amine groups. The excellent quenching effects on top of the gold surface electrode system archive logically inexpensive and straightforward analytical demands. In biochemical sensing analysis, the serotonin dimerization concept demonstrated a robust, low-cost, and highly sensitive immunosensor, presenting the potential of quantifying serotonin at point-of-care (POC) testing. The high-specificity serotonin electrochemical sensor had a limit of detection (LOD) of 0.9 nM in phosphate buffer and 1.4 nM in human serum samples and a linear range of 10 to 400 with a sensitivity of 2.0 × 10^-2 nM. The bivalent 4,4'-dimer-serotonin interaction strategy provides a promising platform for serotonin biosensing with high specificity, sensitivity, selectivity, stability, and reproducibility. The self-assembling gold surface electrochemical system presents a new analytical method for explicitly detecting tiny neurotransmitter-responsive serotonin neuromolecules.

Cryogel Monoliths for Analyte Enrichment by Capture and Release

A platform based on cryogel monoliths in small capillaries, which allows very strong enrichment of an analyte through a capture and release process, is described. For their preparation, a photoreactive copolymer solution containing capture molecules of interest is filled into a capillary, frozen in, and then photochemically transformed into cryogel monoliths through C,H-insertion cross-linking reactions. As a test example, the platform is used for the preconcentration of dopamine from bovine serum albumin and urine samples through capture and release processes. During capture from a large volume and release into a smaller volume, the platform shows recovery rates up to 97% and allows up to a roughly 630-fold enrichment of the concentration of the analyte. The presented platform could be used as a disposable device for the purification and enrichment of a variety of cis-diol-containing samples.

Selective, Ultra-sensitive and Rapid Detection of Serotonin by Optimized ZnO Nanorod FET Biosensor

BACKGROUND

Fluctuation in serotonin (5-HT) level is an essential manifestation of several neurological disorders. In view of such importance, it is necessary to monitor the levels of 5-HT with good sensitivity, selectivity, affordability and low response time. Zinc oxide (ZnO) based field effect transistors (FET) with attributes like minimized noise levels and large on-off ratio are regarded as emerging high performance biosensor platforms. However, their response is significantly non-linear and there has been no appreciable endeavor for improving the non-linearity.

METHOD

In this paper, we have introduced embedded gate electrode encompassing the channel of the FET which improves the uniformity in electric field line distribution through the electrolyte and proportionately enhances the capture of target biomolecule at ultra low concentrations, thereby increasing the linearity. Further, we have incorporated the optimized parameters of ZnO nanorods reported previously, for rapid and selective detection of 5-HT.

RESULTS

It has been observed that the fabricated ZnO FET biosensor lowers the detection limit down to 0.1fM which is at least one order of magnitude lower than the existing reports. The sensor also has wide linear range from 0.1fM to 1nM with a detection time of about 20 minutes.

CONCLUSION

The proposed zinc oxide nanorod-based sensor can be used as an excellent tool for future diagnosis of neurological disorders.

Graphene and Carbon Nanotube-based Electrochemical Sensing Platforms for Dopamine

Dopamine (DA) is an important neurotransmitter, which is created and released from the central nervous system. It plays a crucial role in human activities, like cognition, emotions, and response to anything. Maladjustment of DA in human blood serum results in different neural diseases, like Parkinson's and Schizophrenia. Consequently, researchers have started working on DA detection in blood serum, which is undoubtedly a hot research area. Electrochemical sensing techniques are more promising to detect DA in real samples. However, utilizing conventional electrodes for selective determination of DA encounters numerous problems due to the coexistence of other materials, such as uric acid and ascorbic acid, which have an oxidation potential close to DA. To overcome such problems, researchers have put their focus on the modification of bare electrodes. The aim of this review is to present recent advances in modifications of most used bare electrodes with carbonaceous materials, especially graphene, its derivatives, and carbon nanotubes, for electrochemical detection of DA. A brief discussion about the mechanistic phenomena at the electrode interface has also been included in this review.

Electrochemical Dopamine Biosensor Based on Poly(3-aminobenzylamine) Layer-by-Layer Self-Assembled Multilayer Thin Film

Dopamine (DA) is an important neurotransmitter which indicates the risk of several neurological diseases. The selective determination with low detection limit is necessary for early diagnosis and prevention of neurological diseases associated with abnormal concentration of DA. The purpose of this study is to fabricate a poly(3-aminobenzylamine)/poly(sodium 4-styrenesulfonate) (PABA/PSS) multilayer thin film for use as an electrochemical DA biosensor. The PABA was firstly synthesized using a chemical oxidation method of 3-aminobenzylamine (ABA) monomer with ammonium persulfate (APS) as an oxidant. For electrochemical biosensor, the PABA/PSS thin film was fabricated on fluorine doped tin oxide (FTO)-coated glass substrate using the layer-by-layer (LBL) self-assembly method. The optimized number of bilayers was achieved using SEM and cyclic voltammetry (CV) results. The electroactivity of the optimized LBL thin film toward detection of DA in neutral solution was studied by CV and amperometry. The PABA/PSS thin film showed good sensitivity for DA sensing with sensitivity of 6.922 nA·cm-2·µM-1 and linear range of 0.1-1.0 µM (R2 = 0.9934), with low detection limit of 0.0628 µM, long-term stability and good reproducibility. In addition, the selectivity of the PABA/PSS thin film for detection of DA under the common interferences (i.e., ascorbic acid, uric acid and glucose) was also presented. The prepared PABA/PSS thin film showed the powerful efficiency for future use as DA biosensor in real sample analysis.

Rice-Spikelet-like Copper Oxide Decorated with Platinum Stranded in the CNT Network for Electrochemical In Vitro Detection of Serotonin

The specific monitoring of serotonin (ST) has provoked massive interest in therapeutic and biological science since it has been recognized as the third most significant endogenous gastrointestinal neurotransmitter. Hence, there is a great need to develop a sensitive and low-cost sensing platform for the detection of a clinically relevant ST level in biological matrices. Herein, we develop a simple two-step approach for an ultrasensitive electrochemical (EC) sensor with the Cu₂O metal oxide (MO)-incorporated CNT core that has been further deposited with a transitional amount of platinum nanoparticles (Pt NPs). We presented, for the first time, the deposition of Pt NPs on the (CNTs-Cu₂O-CuO) nanopetal composite via the galvanic replacement method, where copper not only acts as a reductant but a sacrificial template as well. The electrocatalytic aptitude of the fabricated EC sensing platform has been assessed for the sensitive detection of ST as a proficient biomarker in early disease diagnostics. The synergy of improved active surface area, remarkable conductivity, polarization effect induced by Pt NPs on CNTs-Cu₂O-CuO nanopetals, fast electron transfer, and mixed-valence states of copper boost up the redox processes at the electrode-analyte junction. The CNTs-Cu₂O-CuO@Pt-modified electrode has unveiled outstanding electrocatalytic capabilities toward ST oxidation in terms of a low detection limit of 3 nM (S/N = 3), wide linear concentration range, reproducibility, and incredible durability. Owing to the amazing proficiency, the proposed EC sensor based on the CNTs-Cu₂O-CuO@Pt heterostructure has been applied for ST detection in biotic fluids and real-time tracking of ST efflux released from various cell lines as early disease diagnostic approaches.

Structural refinement and electrochemical properties of one dimensional (ZnO NRs)1-x(CNs)x functional hybrids for serotonin sensing studies

Herein, the efficient serotonin (5-HT) sensing studies have been conducted using the (ZnO NRs)1-x(CNs)x nanocomposites (NCs) having appropriate structural and electrochemical properties. Initially, the different compositions of ZnO nanorods (NRs), with varying content of carbon nanostructures (CNs=MWCNTs and RGO), are prepared using simple in-situ wet chemical method and thereafter these NCs have been characterized for physico-chemical properties in correlation to the 5-HT sensing activity. XRD Rietveld refinement studies reveal the hexagonal Wurtzite ZnO NRs oriented in (101) direction with space group 'P63mc' and both orientation as well as phase of ZnO NRs are also retained in the NCs due to the small content of CNs. The interconnectivity between the ZnO NRs with CNs through different functional moieties is also studied using FTIR analysis; while phases of the constituents are confirmed through Raman analysis. FESEM images of the bare/NCs show hexagonal shaped rods with higher aspect ratio (4.87) to that of others. BET analysis and EIS measurements reveal the higher surface area (97.895 m2/g), lower charge transfer resistance (16.2 kΩ) for the ZCNT 0.1 NCs to that of other NCs or bare material. Thereafter, the prepared NCs are deposited on the screen printed carbon electrode (SPCE) using chitosan as cross-linked agent for 5-HT sensing studies; conducted through cyclic voltammetry (CV) and square wave voltammetry (SWV) measurements. Among the various composites, ZCNT0.1 NCs based electrodes exhibit higher sensing activity towards 5-HT in accordance to its higher surface area, lower particle size and lower charge transfer resistance. SWV measurements provide a wide linear response range (7.5-300 μM); lower limit of detection (0.66 μM), excellent limit of quantification (2.19 μM) and good reproducibility to ZCNT 0.1 NCs as compared to others for 5-HT sensing studies.

Employing Conductive Metal-Organic Frameworks for Voltammetric Detection of Neurochemicals

This paper describes the first implementation of an array of two-dimensional (2D) layered conductive metal-organic frameworks (MOFs) as drop-casted film electrodes that facilitate voltammetric detection of redox active neurochemicals in a multianalyte solution. The device configuration comprises a glassy carbon electrode modified with a film of conductive MOF (M₃HXTP₂; M = Ni, Cu; and X = NH, 2,3,6,7,10,11-hexaiminotriphenylene (HITP) or O, 2,3,6,7,10,11-hexahydroxytriphenylene (HHTP)). The utility of 2D MOFs in voltammetric sensing is measured by the detection of ascorbic acid (AA), dopamine (DA), uric acid (UA), and serotonin (5-HT) in 0.1 M PBS (pH = 7.4). In particular, Ni₃HHTP₂ MOFs demonstrated nanomolar detection limits of 63 ± 11 nM for DA and 40 ± 17 nM for 5-HT through a wide concentration range (40 nM-200 μM). The applicability in biologically relevant detection was further demonstrated in simulated urine using Ni₃HHTP₂ MOFs for the detection of 5-HT with a nanomolar detection limit of 63 ± 11 nM for 5-HT through a wide concentration range (63 nM-200 μM) in the presence of a constant background of DA. The implementation of conductive MOFs in voltammetric detection holds promise for further development of highly modular, sensitive, selective, and stable electroanalytical devices.