Halocyclopentadienes: An Emerging Class of Toxic DBPs in Chlor(am)inated Drinking Water

The ideal model for determination the formation potential of priority DBPs during chlorination of free amino acids

Amino acids (AAs) account for about 15-35% of dissolved organic nitrogen (DON), and are known as the important precursors of nitrogenous disinfection by-products (N-DBPs). Determining the formation potential (FP) of AAs to DBPs is used to reveal the key precursors of DBPs for further control, while the ideal method for N-DBPs FP of AAs during chlorination is not revealed. In this study, the ideal FP test models for five classes of priority DBPs during chlorination of four representative AAs (accounted for about 35% of total AAs) were analyzed. For haloaldehydes (HALs), haloketones (HKs), haloacetonitriles (HANs), haloacetamides (HAMs), and halonitromethanes (HNMs), their FPs during chlorination of four AAs were 0.1-13.0, 0.01-1.1, 0.1-104, not detectable (nd)-173, and nd-0.4 μg/mg, respectively. The FPs of priority DBPs had significant deviations between different FP test models and different tested AAs. For HALs, the model, whose chlorine dosage was determined by 15 × molar concentration of AAs [Cl (mM) = 15 × M](named: model II), was the ideal model. For HKs, model II was also the ideal FP test model for AAs with ≤3 carbons, while for AAs with 4 carbons, the model, whose chlorine dosage was determined by keeping the residual chlorine at 1 ± 0.2 mg/L after 24 h of reaction (named: model 4), was the ideal model. For HANs and HNMs, model 4 was the ideal FP test model for most of the studied AAs. The performance of HAMs during chlorination of amino acids was totally different from other P-DBPs, and model 3 was recommended to be the ideal model, in which chlorine dosage was determined by 3 × mass concentration of AAs [Cl (mg/L) = X × DOC]. This study is a reference that helps researchers select an ideal model for N-DBPs FP study of AAs.

VUV coupled with low-dose H2O2 as pretreatment prior to UF: Performance, mechanisms, DBPs formation and toxicity evaluation

Ultrafiltration (UF) is widely used in drinking water plants; however, membrane fouling is unavoidable. Natural organic matter (NOM) is commonly considered as an important pollutant that causes membrane fouling. Herein, we proposed VUV/H2O2 as a UF pretreatment and used UV/H2O2 for comparison. Compared to UV/H2O2, the VUV/H2O2 system presented superior NOM removal. In the VUV/H2O2 system, the steady-state concentration of HO• was approximately twice that in the UV/H2O2 system, which was ascribed to the promoting effect of the 185 nm photons. Specifically, 185 nm photons promoted HO• generation by decomposing mainly H2O at a low H2O2 dose or by decomposing mainly H2O2 at a high H2O2 dose. The VUV/H2O2 pretreatment also demonstrated better membrane fouling mitigation performance than did UV/H2O2. An increase in the H2O2 dose promoted HO• generation, thereby enhancing the performance of NOM degradation and membrane fouling alleviation and shifting the major membrane fouling mechanism from cake filtration to standard blocking. The VUV/H2O2 (0.60 mM) pretreatment effectively reduced disinfection byproducts (DBPs) formation during chlorine disinfection. Additionally, the oxidant H2O2 affected the membrane surface morphology and performance but had no evident effect on the mechanical properties. In actual water treatment, the VUV/H2O2 pretreatment exhibited better performance than the UV/H2O2 pretreatment in easing membrane fouling, ameliorating water quality, and reducing DBPs formation and acute toxicity.

Molecularly imprinted polymers and porous organic frameworks based analytical methods for disinfection by-products in water and wastewater

Disinfection by-products (DBPs) with heritage toxicity, mutagenicity and carcinogenicity are one kind of important new pollutants, and their detection and removal in water and wastewater has become a common challenge facing mankind. Advanced functional materials with ideal selectivity, adsorption capacity and regeneration capacity provide hope for the determination of DBPs with low concentration levels and inherent molecular structural similarity. Among them, molecularly imprinted polymers (MIPs) are favored, owing to their predictable structure, specific recognition and wide applicability. Also, metal-organic frameworks (MOFs) and covalent-organic frameworks (COFs) with unique pore structure, large specific surface area and easy functionalization, attract increasing interest. Herein, we review recent advances in analytical methods based on the above-mentioned three functional materials for DBPs in water and wastewater. Firstly, MIPs, MOFs and COFs are briefly introduced. Secondly, MIPs, MOFs and COFs as extractants, recognition element and adsorbents, are comprehensively discussed. Combining the latest research progress of solid-phase extraction (SPE), sensor, adsorption and nanofiltration, typical examples on MIPs and MOFs/COFs based analytical and removal applications in water and wastewater are summarized. Finally, the application prospects and challenges of the three functional materials in DBPs analysis are proposed to promote the development of corresponding analytical methods.

Emerging disinfection byproducts 3-bromine carbazole induces cardiac developmental toxicity via aryl hydrocarbon receptor activation in zebrafish larvae

3-bromine carbazole (3-BCZ) represents a group of emerging aromatic disinfection byproducts (DBP) detected in drinking water; however, limited information is available regarding its potential cardiotoxicity. To assess its impacts, zebrafish embryos were exposed to 0, 0.06, 0.14, 0.29, 0.58, 1.44 or 2.88 mg/L of 3-BCZ for 120 h post fertilization (hpf). Our results revealed that ≥1.44 mg/L 3-BCZ exposure induced a higher incidence of heart malformation and an elevated pericardial area in zebrafish larvae; it also decreased the number of cardiac muscle cells and thins the walls of the ventricle and atrium while increasing cardiac output and impeding cardiac looping. Furthermore, 3-BCZ exposure also exhibited significant effects on the transcriptional levels of genes related to both cardiac development (nkx2.5, vmhc, gata4, tbx5, tbx2b, bmp4, bmp10, and bmp2b) and cardiac function (cacna1ab, cacna1da, atp2a1l, atp1b2b, atp1a3b, and tnnc1a). Notably, N-acetyl-L-cysteine, a reactive oxygen species scavenger, may alleviate the failure of cardiac looping induced by 3-BCZ but not the associated cardiac dysfunction or malformation; conversely, the aryl hydrocarbon receptor agonist CH131229 can completely eliminate the cardiotoxicity caused by 3-BCZ. This study provides new evidence for potential risks associated with ingesting 3-BCZ as well as revealing underlying mechanisms responsible for its cardiotoxic effects on zebrafish embryos.

Transformation of 6PPDQ during disinfection: Kinetics, products, and eco-toxicity assessment

N-phenyl-N'-(1,3-dimethyl butyl)-p-phenylenediamine-quinone (6PPDQ) currently arouses broad concerns because of its acute lethality to coho salmon and rainbow trout at environmentally relevant concentrations and the wide occurrence in runoff-impacted water. Investigation on the fate and transformation of 6PPDQ in various treatment processes is necessary for its risk assessment and control. Here, we explored the transformation of 6PPDQ during disinfection with its precursor 6PPD as a reference, focusing on kinetics, products, and toxicity variation. 6PPDQ readily reacted with hypochlorite and chlorine dioxide with second-order rate constants of 2580 ± 143 M-1 s-1 and 614 ± 52 M-1 s-1 (pH 7.0 and 25 °C), which are slightly lower than the reactions of 6PPD. We tentatively identified thirteen transformation products for 6PPDQ and eight for 6PPD in reaction with the two disinfectants. It seems that the quinone ring of 6PPDQ and the p-phenylenediamine moiety of 6PPD are reactive sites. The transformation of these compounds probably proceeds through Cl-substitution, ring cleavage, hydroxylation, and amine oxidation and hydrolysis. Tests with zebrafish embryos revealed that the transformation products of 6PPDQ could have higher eco-toxicity than the parent compound, while the toxicity of the 6PPD products remained nearly unchanged. The increased toxicity of 6PPDQ during disinfection highlights the necessity to substantially reduce its content before the disinfection of runoff-impacted water.

Tailoring the topology of ZIF-67 metal-organic frameworks (MOFs) adsorbents to capture humic acids

Chlorination is a versatile technique to combat water-borne pathogens. Over the last years, there has been continued research interest to abate the formation of chlorinated disinfection by-products (DBPs). To prevent hazardous DBPs in drinking water, it is decided to diminish organic precursors, among which humic acids (HA) resulting from the decomposition and transformation of biomass. Metal-organic frameworks (MOFs) such as zeolitic imidazolate frameworks (ZIFs) have recently received tremendous attention in water purification. Herein, customized ZIF-67 MOFs possessing various physicochemical properties were prepared by changing the cobalt source. The HA removal by ZIF-67-Cl, ZIF-67-OAc, ZIF-67-NO3, and ZIF-67-SO4 were 85.6%, 68.9%, 86.1%, and 87.4%, respectively, evidently affected by the specific surface area. HA uptake by ZIF-67-SO4 indicated a removal efficiency beyond 90% in 4  90% after 60 min mixing the solution with 0.3 g L-1 ZIF-67-SO4. Notably, an acceptable removal performance (∼72.3%) was obtained even at HA concentrations up to 100 mg L-1. The equilibrium data fitted well with the isotherm models in the order of Langmuir> Hill > BET> Khan > Redlich-Peterson> Jovanovic> Freundlich > and Temkin. The maximum adsorption capacity qm for HA uptake by ZIF-67-SO4 was 175.89 mg g-1, well above the majority of adsorbents. The pseudo-first-order model described the rate of HA adsorption by time. In conclusion, ZIF-67-SO4 presented promising adsorptive properties against HA. Further studies would be needed to minimize cobalt leaching from the ZIF-67-SO4 structure and improve its reusability safely, to ensure its effectiveness and the economy of adsorption system.

Unravelling High-Molecular-Weight DBP Toxicity Drivers in Chlorinated and Chloraminated Drinking Water: Effect-Directed Analysis of Molecular Weight Fractions

As disinfection byproducts (DBPs) are ubiquitous sources of chemical exposure in disinfected drinking water, identifying unknown DBPs, especially unknown drivers of toxicity, is one of the major challenges in the safe supply of drinking water. While >700 low-molecular-weight DBPs have been identified, the molecular composition of high-molecular-weight DBPs remains poorly understood. Moreover, due to the absence of chemical standards for most DBPs, it is difficult to assess toxicity contributions for new DBPs identified. Based on effect-directed analysis, this study combined predictive cytotoxicity and quantitative genotoxicity analyses and Fourier transform ion cyclotron resonance mass spectrometry (21 T FT-ICR-MS) identification to resolve molecular weight fractions that induce toxicity in chloraminated and chlorinated drinking waters, along with the molecular composition of these DBP drivers. Fractionation using ultrafiltration membranes allowed the investigation of <1 kD, 1-3 kD, 3-5 kD, and >5 kD molecular weight fractions. Thiol reactivity based predictive cytotoxicity and single-cell gel electrophoresis based genotoxicity assays revealed that the <1 kD fraction for both chloraminated and chlorinated waters exhibited the highest levels of predictive cytotoxicity and direct genotoxicity. The <1 kD target fraction was used for subsequent molecular composition identification. Ultrahigh-resolution MS identified singly charged species (as evidenced by the 1 Da spacing in 13C isotopologues), including 3599 chlorine-containing DBPs in the <1 kD fraction with the empirical formulas CHOCl, CHOCl2, and CHOCl3, with a relative abundance order of CHOCl > CHOCl2 ≫ CHOCl3. Interestingly, more high-molecular-weight CHOCl1-3 DBPs were identified in the chloraminated vs chlorinated waters. This may be due to slower reactions of NH2Cl. Most of the DBPs formed in chloraminated waters were composed of high-molecular-weight Cl-DBPs (up to 1 kD) rather than known low-molecular-weight DBPs. Moreover, with the increase of chlorine number in the high-molecular-weight DBPs detected, the O/C ratio exhibited an increasing trend, while the modified aromaticity index (AImod) showed an opposite trend. In drinking water treatment processes, the removal of natural organic matter fractions with high O/C ratio and high AImod value should be strengthened to minimize the formation of known and unknown DBPs.

Contributions of Pharmaceuticals to DBP Formation and Developmental Toxicity in Chlorination of NOM-containing Source Water

Pharmaceuticals have been considered a priority group of emerging micropollutants in source waters in recent years, while their role in the formation and toxicity of disinfection byproducts (DBPs) during chlorine disinfection remains largely unclear. In this study, the contributions of natural organic matter (NOM) and pharmaceuticals (a mixture of ten representative pharmaceuticals) to the overall DBP formation and toxicity during drinking water chlorination were investigated. By innovatively "normalizing" chlorine exposure and constructing a kinetic model, we were able to differentiate and evaluate the contributions of NOM and pharmaceuticals to the total organic halogen (TOX) formation for source waters that contained different levels of pharmaceuticals. It was found that at a chlorine contact time of 1.0 h, NOM (2 mg/L as C) and pharmaceuticals (total 0.0062-0.31 mg/L as C) contributed 79.8-99.5% and 0.5-20.2%, respectively, of TOX. The toxicity test results showed that the chlorination remarkably increased the toxicity of the pharmaceutical mixture by converting the parent compounds into more toxic pharmaceutical-derived DBPs, and these DBPs might contribute significantly to the overall developmental toxicity of chlorinated waters. This study highlights the non-negligible role of pharmaceuticals in the formation and toxicity of overall DBPs in chlorinated drinking water.

Recent progress in identification of water disinfection byproducts and opportunities for future research

Numerous disinfection by-products (DBPs) are formed from reactions between disinfectants and organic/inorganic matter during water disinfection. More than seven hundred DBPs that have been identified in disinfected water, only a fraction of which are regulated by drinking water guidelines, including trihalomethanes, haloacetic acids, bromate, and chlorite. Toxicity assessments have demonstrated that the identified DBPs cannot fully explain the overall toxicity of disinfected water; therefore, the identification of unknown DBPs is an important prerequisite to obtain insights for understanding the adverse effects of drinking water disinfection. Herein, we review the progress in identification of unknown DBPs in the recent five years with classifications of halogenated or nonhalogenated, aliphatic or aromatic, followed by specific halogen groups. The concentration and toxicity data of newly identified DBPs are also included. According to the current advances and existing shortcomings, we envisioned future perspectives in this field.

Occurrence, stability and cytotoxicity of halobenzamides: A new group of nitrogenous disinfection byproducts in drinking water

Exploring disinfection byproducts (DBPs) with adverse health effects in drinking water is a constant challenge. Halobenzamides (HBZAMs) are suspected to be a new group of nitrogenous DBPs but have not been reported in drinking water to date. In this study, by coupling SPE and UPLC‒MS/MS, a sensitive method was established to detect eight HBZAMs in drinking water with recoveries and limits of detection of 80-103% and 0.01-0.04 ng/L, respectively. Subsequently, distinct fragments of HBZAMs were extended to the development of a pseudotargeted method for the analysis of the fourteen HBZAMs that were speculated and lack chemical standards. Using the developed method, eight HBZAMs were quantified in ten drinking water samples with concentrations ranging from 2.4 to 7.2 ng/L and a detection frequency of 100%, among which five HBZAMs were stable with half-lives over 72 h under real chlorine levels. Twelve HBZAMs without standards were identified in three to ten drinking water samples with comparable levels. The cytotoxicity of eight quantified HBZAMs in CHO-K1 cells varied with disparity, in which the cytotoxicity of 3,5-DBBZAM was over 10-fold higher than that of aliphatic dichloroacetamide. Considering their diversity, toxicity and stability, the occurrence of HBZAMs in drinking water deserves attention.

Iron particles lower than 10 μm in drinking water dominate particle catalysis effect on disinfection byproduct formation

Iron particles could catalyze disinfection by-product (DBP) formation in drinking water distribution systems (DWDS), but the catalytic effects of iron particles considering size effects have not been focused. Here, we first found that fine particles (lower than 10 μm) dominated the particle catalysis effect of the iron particles on the formation of DBPs containing multiple Cl atoms (DBP-3Cl), especially those with aromatic structure and containing multiple N atoms (DBP-3N). The loose deposit particles were filtered through 50 μm (F50), 10 μm (F10) and 1 μm (F10) membranes, and their turbidity values were 231.6, 53.4 and 1.1 NTU, respectively. In mass ratio, F50, F10 and F1 accounted for 84 %, 15 % and 1 % of unfiltered samples. Notably, the lower mass F10 generated more DBP-3Cl and DBP-3N than F50. Metal crystals and natural organic matters showed little difference among different sizes. The high catalytic activity of particles in F10 due to size effect was proved to be the essential mechanism. F1 contained few particles to affect DBP formation. In toxicity evaluation, the toxicity of F10 was even higher than F50. Therefore, fine particles with sizes lower than 10 μm may play a dominate role in the catalytic effect on DBP transformation in DWDS.

Formation characteristics and acute toxicity assessment of THMs and HAcAms from DOM and its different fractions in source water during chlorination and chloramination

The formation characteristics of trihalomethanes (THMs) and haloacetamides (HAcAms) from dissolved organic matter and its fractions were investigated during chlorine-based disinfection processes. The relationships between water quality parameters, fluorescence parameters, and the formation levels of THMs and HAcAms were analyzed. The fractions contributing most to the acute toxicity were identified. The trichloromethane (TCM) generation level (72 h) generally followed the order of Cl₂ > NH₂Cl > NHCl₂ process. The NHCl₂ process was superior to the NH₂Cl process in controlling TCM formation. Hydrophobic acidic substance (HOA), hydrophobic neutral substance (HON), and hydrophilic substance (HIS) were identified as primary precursors of 2,2-dichloroacetamide and trichloroacetamide during chlorination and chloramination. The formation of TCM mainly resulted from HOA, HON and HIS fractions relatively uniformly, while HOA and HIS fractions contributed more to the formation of bromodichloromethane and dibromomonochloromethane. UV₂₅₄ could be used as an alternative indicator for the amount of ΣTHMs formed during chlorination and chloramination processes. Dissolved organic nitrogen was a potential precursor of 2,2-dichloroacetamide during chlorination process. The fractions with the highest potential acute toxicity after the chlorination were water-dependent.

Algae impacted drinking water: Does switching to chloramination produce safer drinking water?

Harmful algal (cyanobacterial) blooms (HABs) are increasing throughout the world. HABs can be a direct source of toxins in freshwater sources, and associated algal organic matter (AOM) can act as precursors for the formation of disinfection by-products (DBPs) in drinking water. This study investigated the impacts of algae on DBP formation using treatment with chloramine, which has become a popular disinfectant in the U.S. and in several other countries because it can significantly lower the levels of regulated DBPs formed. Controlled laboratory chloraminations were conducted using live field-collected algal biomass dominated by either Phormidium sp. or Microseira wollei (formerly known as Lyngbya wollei) collected from Lake Wateree and Lake Marion, SC. Sixty-six priority, unregulated or regulated DBPs were quantified using gas chromatography (GC)-mass spectrometry (MS). The presence of HAB-dominated microbial communities in source waters led to significant increases in more toxic nitrogen-containing DBPs (1.5-5 fold) relative to lake waters collected in HAB-free waters. Compared to chlorinated Phormidium-impacted waters, chloraminated waters yielded lower total DBP levels (up to 123 μg/L vs. 586 μg/L for low Br^-/I^- waters), but produced a greater number of brominated, iodinated, and mixed halogenated DBPs in high Br^-/I^- waters. Among the DBPs formed in Phormidium-impacted chloraminated waters, dichloroacetic acid, trichloromethane, chloroacetic acid, chloropropanone, and dichloroacetamide were dominant. For Microseira wollei-impacted chloraminated waters, total DBP concentrations ranged from 33 to 145 μg/L (approximately 3-5 times lower than chlorination), with dichloroacetic acid, dichloroacetamide, and trichloromethane dominant. Overall, chloramination significantly reduced calculated cytotoxicity and genotoxicity in low Br^- and I^- waters, but produced 1.3 fold higher calculated cytotoxicity (compared to chlorine) with high Br^-/I^- waters due to increased formation of more toxic iodo- and mixed halogenated DBPs.

Remarkably efficient Pt/CeO2-Al2O3 catalyst for catalytic hydrodeiodination of monoiodoacetic acid: Synergistic effect of Al2O3 and CeO2

Monoiodoacetic acid (MIAA) is one of the highly toxic halogenated disinfection by-products, which is formed during water disinfection processes. Catalytic hydrogenation with supported noble metal catalyst is a green and effective technique for the transformation of halogenated pollutant, but its activity still needs to be identified. In this study, Pt nanoparticles were supported on CeO₂ modified γ-Al₂O₃ (Pt/CeO₂-Al₂O₃) by chemical deposition method and the synergistic effect of Al₂O₃ and CeO₂ on catalytic hydrodeiodination (HDI) of MIAA was systematically studied. Characterizations revealed that Pt dispersion could be improved by the introduced CeO₂ through the formation of Ce-O-Pt bond and MIAA adsorption could be facilitated by high Zeta potential of Al₂O₃ component. Furthermore, optimal Ptⁿ⁺/Pt⁰ could be obtained by adjusting CeO₂ deposition amount on Al₂O₃, which could effectively facilitate the activation of C-I bond. Therefore, Pt/CeO₂-Al₂O₃ exhibited remarkable catalytic activities and TOF values compared with those of Pt/CeO₂ and Pt/Al₂O_3. Through detailed kinetic experiments and characterization, the extraordinary catalytic performance of Pt/CeO₂-Al₂O₃ can be attributed to the abundant Pt sites as well as the synergistic effect between CeO₂ and Al₂O₃.

Enhanced formation of haloacetonitriles during chlorination with bromide: Unveiling the important roles of organic bromamines

The formation of brominated disinfection byproducts (Br-DBPs) is an emerging issue in drinking water disinfection because its toxicity is tens to hundreds of times higher than that of chlorinated analogues and because of the widespread presence of bromide in source water. However, the mechanism and pathways of Br-DBPs formation remain unclear. In this study, we used glycine, alanine, and serine as model precursors and observed that brominated haloacetonitriles (Br-HANs) were more likely to be formed than brominated trihalomethanes. The results showed that there is not only one important way to HAN formation in the presence of bromide. We propose that organic bromamines, similar to organic chloramines, play a significant role in the formation of Br-HANs. Both the experimental and theoretical results confirmed that the decay of organic bromamines was faster than that of organic chloramines, which verified our assumption. The effect of the pH was investigated to further confirm the role of organic bromamines. In addition, we found that the formation of Br-HANs was significantly inhibited when monochloramine was used as a disinfectant, because the formation of organic bromamines was blocked. However, the formation of Br-HANs was promoted during the UV/chlorine process because of the faster decay of organic bromamines under UV photolysis. Overall, our study reveals the formation mechanism of Br-HANs and provides an alternative method to prevent Br-HAN formation.

The convergence of 2,6-dichloro-1,4-benzoquinone in the whole process of lignin phenol precursor chlorination

The formation and decomposition of 2,6-dichloro-1,4-benzoquinone, an emerging disinfection byproduct (DBP), was studied in the chlorination of lignin phenol precursors. The results show that DCBQ and the related hydroxyl DCBQ (DCBQ-OH) acts as the intermediate products of the chlorination process of the three typical lignin phenol precursors (p-hydroxybenzoic acid, protocatechuic acid, and gallic acid). The contributions of lignin phenol precursors to the overall formation of the targeted DBPs were determined based on the observed abundances of individual lignin phenols and their DBP yields. DCBQ and DCBQ-OH were generated within 2-6 h, the relative abundance of the yields of mol carbon atoms in DCBQ corresponding to the mol carbon atoms in the three model precursors (DCBQ-C) was about 0.01%-14.37% under different pH conditions. With the chlorination reaction time increased (after two or four h), the concentrations of DCBQ and DCBQ-OH entirely decreased, and the decomposition of DCBQ do not follow a pseudo-first-order kinetics during chlorination. Conversely, the decomposition of DCBQ generated from p-hydroxybenzoic acid followed a pseudo-second-order kinetics. Moreover, the formation of trichloromethane (TCM), dichloroacetic acid (DCAA), and trichloroacetic acid (TCAA) was also detected during the chlorination. The contribution of the decomposed DCBQ was mainly to TCAA and the unknown DBPs within 2-12 h, and DCBQ decomposition pathway was affected by pH. Moreover, except for DCBQ/DCBQ-OH and TCM/HAAs, there were still 73.6%-92.41% unknown products (including non-halogenated aromatic DBPs and chlorine-substituted DBPs) needing to identify during the chlorination process for lignin phenols. Overall, revealing the formation and decomposition of DCBQ during the chlorination of lignin phenol precursors would contribute to the effective development of drinking water treatment processes for the removal of highly toxic intermediates generated during disinfection.

Formation of Larger Molecular Weight Disinfection Byproducts from Acetaminophen in Chlorine Disinfection

Acetaminophen is widely used to treat mild to moderate pain and to reduce fever. Under the worldwide COVID-19 pandemic, this over-the-counter pain reliever and fever reducer has been drastically consumed, which makes it even more abundant than ever in municipal wastewater and drinking water sources. Chlorine is the most widely used oxidant in drinking water disinfection, and chlorination generally causes the degradation of organic compounds, including acetaminophen. In this study, a new reaction pathway in the chlorination of acetaminophen, i.e., oxidative coupling reactions via acetaminophen radicals, was investigated both experimentally and computationally. Using an ultraperformance liquid chromatograph coupled to an electrospray ionization-triple quadrupole mass spectrometer, we detected over 20 polymeric products in chlorinated acetaminophen samples, some of which have structures similar to the legacy pollutants "polychlorinated biphenyls". Both C-C and C-O bonding products were found, and the corresponding bonding processes and kinetics were revealed by quantum chemical calculations. Based on the product confirmation and intrinsic reaction coordinate computations, a pathway for the formation of the polymeric products in the chlorination of acetaminophen was proposed. This study suggests that chlorination may cause not only degradation but also upgradation of a phenolic compound or contaminant.