Environmental Applications of Interfacial Materials with Special Wettability

Full-color fiber light-emitting diodes based on perovskite quantum wires

Fiber light-emitting diodes (Fi-LEDs), which can be used for wearable lighting and display devices, are one of the key components for fiber/textile electronics. However, there exist a number of impediments to overcome on device fabrication with fiber-like substrates, as well as on device encapsulations. Here, we uniformly grew all-inorganic perovskite quantum wire arrays by filling high-density alumina nanopores on the surface of Al fibers with a dip-coating process. With a two-step evaporation method to coat a surrounding transporting layer and semitransparent electrode, we successfully fabricated full-color Fi-LEDs with emission peaks at 625 nanometers (red), 512 nanometers (green), and 490 nanometers (sky-blue), respectively. Intriguingly, additional polydimethylsiloxane packaging helps instill the mechanical bendability, stretchability, and waterproof feature of Fi-LEDs. The plasticity of Al fiber also allows the one-dimensional architecture Fi-LED to be shaped and constructed for two-dimensional or even three-dimensional architectures, opening up a new vista for advanced lighting with unconventional formfactors.

Effective separation of water-in-oil emulsions using an under-medium superlyophilic membrane with hierarchical pores

Separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. To address the challenges posed by the water-oil interface, superwetting materials have been designed to accomplish separation through filtration and adsorption. Superhydrophobic membranes prevent the permeation of water droplets owing to extreme repellence and their size-sieving abilities. However, their use in remediating water-contaminated oil is limited by high oil viscosities. Meanwhile, in-air superhydrophilic sorbents are rarely employed for the separation of water-in-oil emulsions due to the thermodynamic and kinetic limitations of water adsorption in oil. Herein, the integration of an under-medium superlyophilic membrane with the hierarchical porous structure of wood is presented for filtration-driven selective adsorption of water from surfactant-stabilized (10 g/L) water-in-oil emulsions. Compared to filtration through a natural wood membrane or direct adsorption using an under-oil superhydrophilic wood membrane, the under-medium superlyophilic wood membrane demonstrated high separation efficiencies of > 99.95% even when applied to the regeneration of high-viscosity lubricating (6.3 mPa s) and edible (50.5 mPa s) oils, exhibiting viscosity-dependent fluxes and excellent stability. Moreover, the cost of purifying 200 mL of lubricating oil using the modified wood membrane was much lower than the oil's market price and required a low energy consumption of ca. 1.72 kWh. ENVIRONMENTAL IMPLICATION: The ever-growing use of petroleum and industrial/domestic oil products has led to excessive (estimated at a million tons per year) output of waste oils. Because direct discharge of waste oils into the environment causes serious pollution problems, separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. Here filtration-driven water adsorption has been demonstrated to be a feasible method for the remediation of water-contaminated waste oils, even those that are highly viscous.

The antifouling mechanism and application of bio-inspired superwetting surfaces with effective antifouling performance

With the rapid development of industries, the issue of pollution on Earth has become increasingly severe. This has led to the deterioration of various surfaces, rendering them ineffective for their intended purposes. Examples of such surfaces include oil rigs, seawater intakes, and more. A variety of functional surface techniques have been created to address these issues, including superwetting surfaces, antifouling coatings, nano-polymer composite materials, etc. They primarily exploit the membrane's surface properties and hydration layer to improve the antifouling property. In recent years, biomimetic superwetting surfaces with non-toxic and environmental characteristics have garnered massive attention, greatly aiding in solving the problem of pollution. In this work, a detailed presentation of antifouling superwetting materials was made, including superhydrophobic surface, superhydrophilic surface, and superhydrophilic/underwater superoleophobic surface, along with the antifouling mechanisms. Then, the applications of the superwetting antifouling materials in antifouling domain were addressed in depth.

Interfacial Solar Evaporation: From Fundamental Research to Applications

In the last decade, interfacial solar steam generation (ISSG), powered by natural sunlight garnered significant attention due to its great potential for low-cost and environmentally friendly clean water production in alignment with the global decarbonization efforts. This review aims to share the knowledge and engage with a broader readership about the current progress of ISSG technology and the facing challenges to promote further advancements toward practical applications. The first part of this review assesses the current strategies for enhancing the energy efficiency of ISSG systems, including optimizing light absorption, reducing energy losses, harvesting additional energy, and lowering evaporation enthalpy. Subsequently, the current challenges faced by ISSG technologies, notably salt accumulation and bio-fouling issues in practical applications, are elucidated and contemporary methods are discussed to overcome these challenges. In the end, potential applications of ISSG, ranging from initial seawater desalination and industrial wastewater purification to power generation, sterilization, soil remediation, and innovative concept of solar sea farm, are introduced, highlighting the promising potential of ISSG technology in contributing to sustainable and environmentally conscious practices. Based on the review and in-depth understanding of these aspects, the future research focuses are proposed to address potential issues in both fundamental research and practical applications.

Analysis of Carbon Nanoparticle Coatings via Wettability

Wettability, typically estimated through the contact angle, is a fundamental property of surfaces with wide-ranging implications in both daily life and industrial processes. Recent scientific interest has been paid to the surfaces exhibiting extreme wettability: superhydrophobic and superhydrophilic surfaces, characterized by high water repellency and exceptional water wetting, respectively. Both chemical composition and morphology play a role in the determination of the wettability "performance" of a surface. To tune surface-wetting properties, we considered coatings of carbon nanoparticles (CNPs) in this study. They are a new class of nanomaterials synthesized in flames whose chemistry, dimension, and shape depend on combustion conditions. For the first time, we systematically studied the wettability of CNP coatings produced in a controlled rich ethylene/air flame stabilized over a McKenna burner. A selected substrate was intermittently inserted in the flame at 15 mm above the burner to form a thin coating thanks to a thermophoretic-driven deposition mechanism. The chemical-physical quality and the deposed quantity of the CNPs were varied by opportunely combing the substrate flame insertion number (from 1 to 256) and the carbon-to-oxygen ratio, C/O (from 0.67 to 0.87). The wettability of the coatings was evaluated by measuring the contact angle, CA, with the sessile drop method. When the C/O = 0.67, the CNPs were nearly spherical, smaller than 8 nm, and always generated hydrophilic coatings (CA < 35°). At higher C/O ratios, the CNPs reached dimensions of 100 nm, and fractal shape aggregates were formed. In this case, either hydrophilic (CA < 76°) or superhydrophobic (CA ~166°) behavior was observed, depending on the number of carbon nanoparticles deposed, i.e., film thickness. It is known that wettability is susceptible to liquid surface tension, and therefore, tests were conducted with different fluids to establish a correlation between the flame conditions and the nanostructure of the film. This method offers a fast and simple approach to determining mesoscale information for coating roughness and topographical homogeneity/inhomogeneity of their surfaces.

Flexible Platform Composed of T-Shaped Micropyramid Patterns toward a Waterproof Sensing Interface

Antifouling is essential to guaranteeing the sensitivity and precision of flexible sensing interfaces. Materials and structures are the two primary strategies. However, optimizing the inherent microstructures to integrate waterproofing and sensing is rarely reported. To improve the liquid repellency of micropyramid structures, this work presents a study of the design and fabrication of T-shaped micropyramid structures. These structures are patterned uniformly and largely on polydimethylsiloxane (PDMS) skin by the new process of two-step magnetic induction. The waterproofing is related to the breakthrough pressure and the liquid repellency, both of which are a function of structural characteristics, D, and material properties, θY. At the breakthrough transition, two failure models distinguished by θY appear: the depinning transition and the sagging transition. Meanwhile, when considering D in practice, some models will shift and occur early. The D value regulates the transition of the material's wettability to the liquid repellency. The influence of the material's inherent nonwettability on liquid repellency diminishes as D decreases, and the transition from completely wetting liquids to super-repellents can be achieved. Experiments demonstrate that for D = 0.3 under water the resistance is approximately 142 times larger than the depth of the structure, considerably facilitating the waterproofing of conventional micropyramid arrays. This work provides a novel method for fabricating flexible T-shaped micropyramid array structures and opens a new window on flexible sensing interfaces with excellent waterproofing.

Sterilized Polyhexanide-Releasing Chitosan Membranes with Potential for Use in Antimicrobial Wound Dressings

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited a water swelling capacity of 748%, a water drop penetration time of 11 s in a dry membrane and a water vapor transmission rate of 34,400 g H2O/m2/24 h when in contact with water. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. When these membranes and a commercial PHMB-releasing AMD were assayed under the same conditions, albeit far from the in vivo conditions, their drug release kinetics were comparable, releasing PHMB for ca. 6 and 4 h, respectively. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds and blood clotting activity. The obtained results suggest that these membranes may have potential for use in the development of AMDs.

Overview of the design of bionic fine hierarchical structures for fog collection

Nature always uses its special wisdom to construct elegant and suitable schemes. Consequently, organisms in the flora and fauna are endowed with fine hierarchical structures (HS) to adapt to the harsh environment due to many years of evolution. Water is one of the most important resources; however, easy access to it is one the biggest challenges faced by human beings. In this case, fog collection (FC) is considered an efficient method to collect water, where bionic HS can be the bridge to efficiently facilitate the process of the FC. In this review, firstly, we discuss the basic principles of FC. Secondly, the role of HS in FC is analyzed in terms of the microstructure of typical examples of plants and animals. Simultaneously, the water-harvesting function of HS in a relatively new organism, fungal filament, is also presented. Thirdly, the HS design in each representative work is analyzed from a biomimetic perspective (single to multiple biomimetic approaches). The role of HS in FC, and then the FC performance of each work are analyzed in order of spatial dimension from a bionic perspective. Finally, the challenges at this stage and the outlook for the future are presented.

3D Printing of Ti-6Al-4V-Based Porous-Channel Dental Implants: Computational, Biomechanical, and Cytocompatibility Analyses

Objective: Loosening of dental implants due to resorption of the surrounding bone is one of the challenging clinical complications in prosthetic dentistry. Generally, stiffness mismatch between an implant and its surrounding bone is one of the major factors. In order to prevent such clinical consequences, it is essential to develop implants with customized stiffness. The present study investigates the computational and experimental biomechanical responses together with cytocompatibility studies of three-dimensional (3D)-printed Ti-6Al-4V-based porous dental implants with varied stiffness properties. Methods: Additive manufacturing (direct metal laser sintering, DMLS) was utilized to create Ti-6Al-4V implants having distinct porosities and pore sizes (650 and 1000 μm), along with a nonporous (solid) implant. To validate the compression testing of the constructed implants and to probe their biomechanical response, finite element models were employed. The cytocompatibility of the implants was assessed using MG-63 cells, in vitro. Results: Both X-ray microcomputed tomography (μ-CT) and scanning electron microscopy (SEM) studies illustrated the ability of DMLS to produce implants with the designed porosities. Biomechanical analysis results revealed that the porous implants had less stiffness and were suitable for providing the appropriate peri-implant bone strain. Although all of the manufactured implants demonstrated cell adhesion and proliferation, the porous implants in particular supported better bone cell growth and extracellular matrix deposition. Conclusions: 3D-printed porous implants showed tunable stiffness properties with clinical translational potential.

Recyclable Superhydrophobic Surface Prepared via Electrospinning and Electrospraying Using Waste Polyethylene Terephthalate for Self-Cleaning Applications

Superhydrophobic surfaces, i.e., surfaces with a water contact angle (WCA) ≥ 150°, have gained much attention as they are multifunctional surfaces with features such as self-cleaning, which can be useful in various applications such as those requiring waterproof and/or protective films. In this study, we prepared a solution from recycled polyethylene terephthalate (PET) and fabricated a superhydrophobic surface using electrospinning and electrospraying processes. We observed that the fabricated geometry varies depending on the solution conditions, and based on this, we fabricated a hierarchical structure. From the results, the optimized structure exhibited a very high WCA (>156.6°). Additionally, our investigation into the self-cleaning functionality and solar panel efficiency of the fabricated surface revealed promising prospects for the production of superhydrophobic surfaces utilizing recycled PET, with potential applications as protective films for solar panels. Consequently, this research contributes significantly to the advancement of environmentally friendly processes and the progress of recycling technology.

Electrospun nanofibrous membranes for membrane distillation application-A dynamic life cycle assessment (dLCA) approach

Membrane distillation (MD) for water desalination and purification has been gaining prominence to address the issues relating to water security and the destruction of aquatic ecosystems globally. Recent advances in electrospun membranes for MD application have improved antifouling and anti-wetting performance. However, the environmental impacts associated with producing novel electrospun membranes still need to be clarified. It is imperative to quantify and analyze the tradeoffs between membrane performance and impacts at the early stages of research on these novel membranes. Life Cycle Assessment (LCA) is an appropriate tool to systematically account for environmental performance, all the way from raw material extraction to the disposal of any product, process, or technology. The inherent lack of detailed datasets for emerging technologies contributes to significant uncertainties, making the adoption of traditional LCA challenging. A dynamic LCA (dLCA) is performed to guide the sustainable design and selection of emerging electrospun poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) electrospun membrane (E-PH) and hybridizing polydimethylsiloxane (PDMS) on E-PH membrane (E-PDMS) for dyeing wastewater treatment technologies. The associated environmental impacts are related to the high energy demands required for fabricating electrospun nanofibrous membranes. After LCA analysis, the E-PDMS membrane emerges as a promising membrane, due to the relatively low impact/benefit ratio and the high performance achieved in treating dyeing wastewater.

Biodegradable electrospinning superhydrophilic nanofiber membranes for ultrafast oil-water separation

Although membrane technology has attracted considerable attention for oily wastewater treatment, the plastic waste generated from discarded membranes presents an immediate challenge for achieving eco-friendly separation. We designed on-demand biodegradable superhydrophilic membranes composed of polylactic acid nanofibers in conjunction with polyethylene oxide hydrogels using electrospinning technology for ultrafast purification of oily water. Our results showed that the use of the polyethylene oxide hydrogels increased the number of hydrogen bonds formed between the membrane surface and water molecules by 357.6%. This converted hydrophobic membranes into superhydrophilic ones, which prevented membrane fouling and accelerated emulsion penetration through the membranes. The oil-in-water emulsion permeance of our newly designed nanofiber membranes increased by 61.9 times (2.1 × 104 liters per square meter per hour per bar) with separation efficiency >99.6%, which was superior to state-of-the-art membranes. Moreover, the formation of hydrogen bonds was found to accelerate polylactic acid biodegradation into lactic acid by over 30%, offering a promising approach for waste membrane treatment.

Biomimetic surfaces: Insights on the role of surface topography and wetting properties in bacterial attachment and biofilm formation

The study explores the impact of biomimetic surfaces on bacterial attachment and biofilm formation. Specifically, it investigates the effects of topographic scale and wetting behavior on the attachment and growth of Staphylococcus aureus and Escherichia coli on four different biomimetic surfaces: rose petals, Paragrass leaves, shark skin, and goose feathers. Using soft lithography, epoxy replicas with surface topographies similar to those of the natural surfaces were created. The static water contact angles of the replicas exceeded the hydrophobic threshold of 90°, while the hysteresis angles were found to be in the order of goose feathers, shark skin, Paragrass leaves, and rose petals. The results showed that bacterial attachment and biofilm formation were the lowest on rose petals and the highest on goose feathers, regardless of the bacterial strain. Additionally, the study revealed that surface topography had a significant impact on biofilm formation, with smaller feature sizes inhibiting biofilm formation. Hysteresis angle, rather than static water contact angle, was identified as a critical factor to consider when evaluating bacterial attachment behavior. These unique insights have the potential to lead to the development of more effective biomimetic surfaces for the prevention and eradication of biofilms, ultimately improving human health and safety.

Superhydrophobic cotton fabrics for effective removal of high-density polyethylene and polypropylene microplastics: Insights from surface and colloidal analysis

HYPOTHESIS

The use of superhydrophobic materials to remove particulate pollutants such as microplastics is still in its infancy. In a previous study, we investigated the effectiveness of three different types of superhydrophobic materials - coatings, powdered materials, and meshes - for removing microplastics. In this study, we will explain the removal process by considering microplastics as colloids and taking into account their wetting properties as well as those of a superhydrophobic surface. The process will be explained through the interactions of electrostatic forces, van der Waals forces, and the DLVO theory.

EXPERIMENTS

In order to replicate and verify the previous experimental findings on the removal of microplastics using superhydrophobic surfaces, we have modified non-woven cotton fabrics with polydimethylsiloxane. We then proceeded to remove high-density polyethylene and polypropylene microplastics from water by introducing oil at the microplastics-water interface, and we determined the removal efficiency of the modified cotton fabrics.

FINDINGS

After achieving a superhydrophobic non-woven cotton fabric (159 ± 1°), we confirmed its effectiveness in removing high-density polyethylene and polypropylene microplastics from water with a removal efficiency of 99%. Our findings suggest that the binding energy of microplastics increases and the Hamaker constant becomes positive when they are present in oil instead of water, leading to their aggregation. As a result, electrostatic interactions become negligible in the organic phase, and van der Waals interactions become more important. The use of the DLVO theory allowed us to confirm that solid pollutants can be easily removed from the oil using superhydrophobic materials.

Review on Hydrophobic Thin Films Prepared Using Magnetron Sputtering Deposition

Hydrophobic thin films have gained significant attention due to their broad applications in self-cleaning, anti-corrosion, anti-icing, medicine, oil-water separation, and other fields. The target hydrophobic materials can be deposited onto various surfaces thanks to the scalable and highly reproducible nature of magnetron sputtering, which is comprehensively overviewed in this review. While alternative preparation methods have been extensively analyzed, a systematic understanding of hydrophobic thin films fabricated using magnetron sputtering deposition is still absent. After outlining the fundamental mechanism of hydrophobicity, this review briefly summarizes three types of sputtering-deposited thin films that originate from oxides, polytetrafluoroethylene (PTFE), and diamond-like carbon (DLC), respectively, primarily focusing on the recent advances in their preparation, characteristics, and applications. Finally, the future applications, current challenges, and development of hydrophobic thin films are discussed, and a brief perspective on future research directions is provided.

Bio-sorbent from castor oil polyurethane foam containing cellulose-halloysite nanocomposite for removal of manganese, nickel and cobalt ions from water

In order to mitigate the contamination of water with heavy metals, caused by mining dam failures in Brumadinho and Mariana in Brazil, eco-friendly bio-based castor oil polyurethane foams, containing a cellulose-halloysite green nanocomposite were prepared. Polyurethane foams containing none (PUF-0), 5%wt (PUF-5), and 10%wt (PUF-10) of the nanocomposite were obtained. The application of the material in aqueous media was verified through an investigation of the efficiency of adsorption, the adsorption capacity, and the adsorption kinetics in pH= 2 and pH= 6.5 for manganese, nickel, and cobalt ions. An increase of 5.47 times in manganese adsorption capacity was found after only 30 min in contact with a solution having this ion at pH= 6.5 for PUF-5 and 11.38 times for PUF-10 when both were compared with PUF-0. Adsorption efficiency was respectively 68.17% at pH= 2 for PUF-5% and 100% for PUF-10 after 120 h, while for the control foam, PUF-0, the adsorption efficiency was only 6.90%.

Molecular dynamics simulations of water-ethanol droplet on silicon surface

Molecular dynamics simulations are used to explore the wetting behavior of a water-ethanol droplet on the silicon surface. The effect of ethanol concentration on the wettability of a water-ethanol droplet on the silicon surface was analysed by calculation of contact angle. At 30% ethanol concentrations, the water contact angle was 50.7°, while at 50% ethanol concentrations, it was 36°. The results showed that the contact angle of a droplet on a silicon surface decreases with increasing ethanol concentrations. The formation of hydrogen bonds (HBs) between water-water molecules was 677 for the 30% ethanol system, while at 50% ethanol concentrations, it was 141. The number of hydrogen bonds between water molecules reduces as the ethanol concentrations rise. The HBs between water molecules and the silicon surface is seen to grow as the ethanol concentration rises. The overall potential energies of pure water, 7:3 water-ethanol, and 1:1 water-ethanol systems are −74.4, −96.16, and −158.59 kcal/mol, respectively. The contact angle and number density of water molecules on the surface of the silicon revealed that at different ethanol concentrations, more water molecules are distributed on the silicon surface.

Anisotropic cellulose nanocrystalline sponge sheets with ultrahigh water fluxes and oil/water selectivity

Oily sewage caused by oil spill accidents has become a severe problem in the last decades. Hence, two-dimensional sheet-like filter materials for oil/water separation have received widespread attention. Porous sponge materials were developed using cellulose nanocrystals (CNCs) as raw materials. They are environmentally friendly and easy to prepare, with high flux and separation efficiency. The 1,2,3,4-butane tetracarboxylic acid cross-linked anisotropic cellulose nanocrystalline sponge sheet (B-CNC) exhibited ultrahigh water fluxes driven by gravity alone, depending on the aligned structure of channels and the rigidity of CNCs. Meanwhile, the sponge gained superhydrophilic/underwater superhydrophobic wettability with an underwater oil contact angle of up to 165.7° due to its ordered micro/nanoscale structure. B-CNC sheets displayed high oil/water selectivity without additional material doping or chemical modification. For oil/water mixtures, high separation fluxes of approximately 100,000 L·m^-2·h^-1 and separation efficiencies of up to 99.99 % were obtained. For a Tween 80-stabilized toluene-in-water emulsion, the flux reached >50,000 L·m^-2·h^-1, and the separation efficiency was above 99.7 %. B-CNC sponge sheets showed significantly higher fluxes and separation efficiencies than other bio-based two-dimensional materials. This research provides a facile and straightforward fabrication method of environmental-friendly B-CNC sponges for rapid, selective oil/water separation.

Bioinspired Graphene Oxide-Magnetite Nanocomposite Coatings as Protective Superhydrophobic Antifouling Surfaces

Antifouling (AF) nanocoatings made of polydimethylsiloxane (PDMS) are more cost-efficient and eco-friendly substitutes for the already outlawed tributyltin-based coatings. Here, a catalytic hydrosilation approach was used to construct a design inspired by composite mosquito eyes from non-toxic PDMS nanocomposites filled with graphene oxide (GO) nanosheets decorated with magnetite nanospheres (GO-Fe₃O₄ nanospheres). Various GO-Fe₃O₄ hybrid nanofillers were dispersed into the PDMS resin through a solution casting method to evaluate the structure-property relationship. A simple coprecipitation procedure was used to fabricate magnetite nanospheres with an average diameter of 30-50 nm, a single crystal structure, and a predominant (311) lattice plane. The uniform bioinspired superhydrophobic PDMS/GO-Fe₃O₄ nanocomposite surface produced had a micro-/nano-roughness, low surface-free energy (SFE), and high fouling release (FR) efficiency. It exhibited several advantages including simplicity, ease of large-area fabrication, and a simultaneous offering of dual micro-/nano-scale structures simply via a one-step solution casting process for a wide variety of materials. The superhydrophobicity, SFE, and rough topology have been studied as surface properties of the unfilled silicone and the bioinspired PDMS/GO-Fe₃O₄ nanocomposites. The coatings' physical, mechanical, and anticorrosive features were also taken into account. Several microorganisms were employed to examine the fouling resistance of the coated specimens for 1 month. Good dispersion of GO-Fe₃O₄ hybrid fillers in the PDMS coating until 1 wt % achieved the highest water contact angle (158° ± 2°), the lowest SFE (12.06 mN/m), micro-/nano-roughness, and improved bulk mechanical and anticorrosion properties. The well-distributed PDMS/GO-Fe₃O₄ (1 wt % nanofillers) bioinspired nanocoating showed the least biodegradability against all the tested microorganisms [Kocuria rhizophila (2.047%), Pseudomonas aeruginosa (1.961%), and Candida albicans (1.924%)]. We successfully developed non-toxic, low-cost, and economical nanostructured superhydrophobic FR composite coatings for long-term ship hull coatings. This study may expand the applications of bio-inspired functional materials because for multiple AF, durability and hydrophobicity are both important features in several industrial applications.

Anion Effect on Forward Osmosis Performance of Tetrabutylphosphonium-Based Draw Solute Having a Lower Critical Solution Temperature

The applicability of ionic liquids (ILs) as the draw solute in a forward osmosis (FO) system was investigated through a study on the effect of the structural change of the anion on the FO performance. This study evaluated ILs composed of tetrabutylphosphonium cation ([P₄₄₄₄]⁺) and benzenesulfonate anion ([BS]^-), para-position alkyl-substituted benzenesulfonate anions (p-methylbenzenesulfonate ([MBS]^-) and p-ethylbenzenesulfonate ([EBS^-]), and methanesulfonate anion ([MS]^-). The analysis of the thermo-responsive properties suggested that the [P₄₄₄₄][MBS] and [P₄₄₄₄][EBS] ILs have lower critical solution temperatures (LCSTs), which play a beneficial role in terms of the reusability of the draw solute from the diluted draw solutions after the water permeation process. At 20 wt% of an aqueous solution, the LCSTs of [P₄₄₄₄][MBS] and [P₄₄₄₄][EBS] were approximately 36 °C and 25 °C, respectively. The water flux and reverse solute flux of the [P₄₄₄₄][MBS] aqueous solution with higher osmolality than [P₄₄₄₄][EBS] were 7.36 LMH and 5.89 gMH in the active-layer facing the draw solution (AL-DS) mode at osmotic pressure of 25 atm (20 wt% solution), respectively. These results indicate that the [P₄₄₄₄]⁺-based ionic structured materials with LCST are practically advantageous for application as draw solutes.

Synthesis of Superhydrophobic/Superoleophilic stearic acid and Polymer-modified magnetic polyurethane for Oil-Water Separation: Effect of polymeric nature

The superhydrophobic/superoleophilic materials based on polyurethane foams have been layered with three different polymers and extensive modification with iron/magnetic nanocomposite. The general desires are to study the effect of the polymer layer and to eliminate the oil contaminant from the oil-water system which is crucial due to the development of environmental technologies. These materials were generated by facile dip-coating two-step method on the polyurethane foams (PUF) surface. PUF was directly layered with polydopamine/polypyrrole/polyaniline (PDA/PPy/PANI) and incorporated with Fe-SA (stearic acid) nanocomposites by ultrasonication and refluxing. In addition, characterization by FTIR, SEM/EDX, XRD, and TGA presented that the polymer layer and Fe-SA nanocomposites successfully covered the PUF surface caused by the chelating interaction between the carboxylates and active sites on iron particles due to intermolecular hydrogen bond interaction. Interestingly, the water contact angle (WCA) measurement of the nanocomposites displayed that the contact angle significantly improved up to 164°. After 20 cycles of oil absorption capacity, the WCA steadily remained up to 153° indicating powerful superhydrophobic properties of the materials. Furthermore, the oil absorption capacity of the materials was evaluated using typical oil-water separation methods such as reusability, separation efficiency, and oil permeate flux. The results exhibited that the modified PUFs have enhanced the absorption capacity up to 44 times the foam weight, 99 % separation efficiency, and about 8000 L.m-2.h-1 oil flux. For oil removal, the dyed oil phase was rapidly absorbed within 2 s confirming the highly used products for a wide area of oil-water separation. PDA-coated PUF nanocomposites obtained the most outstanding results due to their remarkable interfacial adhesion properties which provide larger active functional groups for hydrogen bonding interaction on PUF surface and Fe-SA nanocomposites.

Which Surface Is More Scaling Resistant? A Closer Look at Nucleation Theories for Heterogeneous Gypsum Nucleation in Aqueous Solutions

Developing engineered surfaces with scaling resistance is an effective means to inhibit surface-mediated mineral scaling in various industries including desalination. However, contrasting results have been reported on the relationship between scaling potential and surface hydrophilicity. In this study, we combine a theoretical analysis with experimental investigation to clarify the effect of surface wetting property on heterogeneous gypsum (CaSO₄·2H₂O) formation on surfaces immersed in aqueous solutions. Theoretical prediction derived from classical nucleation theory (CNT) indicates that an increase of surface hydrophobicity reduces scaling potential, which contrasts our experimental results that more hydrophilic surfaces are less prone to gypsum scaling. We further consider the possibility of nonclassical pathway of gypsum nucleation, which proceeds by the aggregation of precursor clusters of CaSO₄. Accordingly, we investigate the affinity of CaSO₄ to substrate surfaces of varied wetting properties via calculating the total free energy of interaction, with the results perfectly predicting experimental observations of surface scaling propensity. This indicates that the interactions between precursor clusters of CaSO₄ and substrate surfaces might play an important role in regulating heterogeneous gypsum formation. Our findings provide evidence that CNT might not be applicable to describing gypsum scaling in aqueous solutions. The fundamental insights we reveal on gypsum scaling mechanisms have the potential to guide rational design of scaling-resistant engineered surfaces.

Structural design of the electrospun nanofibrous membrane for membrane distillation application: a review

Although membrane distillation (MD) is a promising technology for water desalination and industrial wastewater treatment, the MD process is not widely applied in the global water industry due to the lack of a suitable membrane for the MD process. The design and appropriate manufacture are the most important factors for MD membrane optimization. The well-designed porous structure, superhydrophobic surface, and pore-wetting prevention of the membrane are vital properties of the MD membrane. Nowadays, electrospinning that is capable of manufacturing membranes with superhydrophobic or omni phobic properties is considered a promising technology. Electrospun nanofibrous membranes (ENMs) possess the characteristics of cylindrical morphology, re-entrant structure, and easy-shaping for a specific purpose, benefiting the membrane design and modification. Based on that, this review investigates the current state and future progress of the superhydrophobic, multi-layer, and omniphobic ENMs manufactured with various structural designs for seawater desalination and wastewater purification. We expect that this paper will provide some recommendations and guidance for further fabrication research and the configuration design of ENMs in the MD process for seawater desalination and wastewater purification.

A Superhydrophilic, Light/Microwave-Absorbing Coating with Remarkable Antibacterial Efficacy

Driven by the overuse of antibiotics, pathogenic infections, dominated by the rapid emergence of antibiotic resistant bacteria, have become one of the greatest current global health challenges. Thus, there is an urgent need to explore novel strategies that integrate multiple antibacterial modes to deal with bacterial infections. In this work, a Co(Ni,Ag)/Fe(Al,Cr)₂O₄ composite duplex coating was fabricated using template-free sputtering deposition technology. The phase constitution of the coating was estimated to be 79 wt % Fe(Al,Cr)₂O₄ phase and 21 wt % of an Ag-containing metallic phase. The composite coating consisted of a ∼10 μm-thick porous outer-layer and a ∼6 μm-thick compact inner-layer, in which the outer-layer is composed of a densely stacked array of microscale cones. After exposure to ambient air for 14 days, the composite coating showed a wettability transition from a superhydrophilic nature to exhibit adhesive superhydrophobic behavior with a water contact angle of 142° ± 2.8°, but it reverted to its initial superhydrophilic state after annealing in air at 200 °C for 5 h. The absorption rate of the as-received composite coating exceeds 99% in a broad band spanning both the visible and NIR regions and showed a high photothermal efficiency to convert photon energy into heat. Similarly, the composite coating showed microwave absorption behavior with a minimum reflection loss value of 38 dB at 4.4 GHz. In vitro antibacterial tests were used to determine the antibacterial behavior of the composite coating against Escherichia coli and Staphylococcus aureus after 60 min of visible light irradiation. After this exposure, the as-prepared composite coating exhibited nearly 100% bactericidal efficiency against these bacteria. The antibacterial behavior of the coating was attributed to the synergistic effects of the superhydrophilic surface, the release of Ag⁺ ions, and the photothermal effect. Therefore, this composite coating may be a promising candidate to efficiently combat medical device-associated infections.

Construction of durable superhydrophilic activated carbon fibers based material for highly-efficient oil/water separation and aqueous contaminants degradation

Developing filtering materials with high permeation flux and contaminant removal rate is of great importance for oily wastewater remediation. Herein, a robust three-dimensional (3D) activated carbon fibers (ACFs) based composite with uniformly grown layered double hydroxide (LDH) on the surface was successfully constructed through a feasible hydrothermal strategy. The LDH with a high surface energy and vertically aligned structure could provide superhydrophilicity to ACFs. Systematic investigation confirmed that the 3D material could overcome the size mismatch between the ACFs macropores and tiny emulsified droplets through the combination of size-sieving filtration on the surface and oil droplet coalescence in the fiber network. This process efficiently separated the intractable surfactant-stabilized oil-in-water emulsions with high permeation flux (up to 4.16 × 10⁶ L m^-2 h^-1 bar^-1). Notably, the LDH also had well-dispersed catalytic active sites, which could initiate advanced oxidation processes (AOPs) to efficiently eliminate various types of water-soluble organic pollutants (e.g., pharmaceuticals, phenolic compounds and organic dyes). The resulting modified ACFs exhibited exceptional removal rates for both oil and organic pollutants in the complex sewage during the continuous filtration process. These versatile abilities integrated with the facile preparation method reported herein provide outstanding prospects for the large-scale treatment of oily wastewater.

Fundamentals and utilization of solid/ liquid phase boundary interactions on functional surfaces

The affinity of macroscopic solid surfaces or dispersed nano- and bioparticles towards liquids plays a key role in many areas from fluid transport to interactions of the cells with phase boundaries. Forces between solid interfaces in water become especially important when the surface texture or particles are in the colloidal size range. Although, solid-liquid interactions are still prioritized subjects of materials science and therefore are extensively studied, the related literature still lacks in conclusive approaches, which involve as much information on fundamental aspects as on recent experimental findings related to influencing the wetting and other wetting-related properties and applications of different surfaces. The aim of this review is to fill this gap by shedding light on the mechanism-of-action and design principles of different, state-of-the-art functional macroscopic surfaces, ranging from self-cleaning, photoreactive or antimicrobial coatings to emulsion separation membranes, as these surfaces are gaining distinguished attention during the ongoing global environmental and epidemic crises. As there are increasing numbers of examples for stimulus-responsive surfaces and their interactions with liquids in the literature, as well, this overview also covers different external stimulus-responsive systems, regarding their mechanistic principles and application possibilities.

Electro-Enhanced Separation of Microsized Oil-in-Water Emulsions via Metallic Membranes: Performance and Mechanistic Insights

Conventional separation membranes suffer from evitable fouling and flux decrease for water treatment applications. Herein, a novel protocol of electro-enhanced membrane separation is proposed for the efficient treatment of microsized emulsions (∼1 μm) by rationally designing robust electroresponsive copper metallic membranes, which could mitigate oil fouling and coenhance permeance (from ∼1026 to ∼2516 L·m^-2·h^-1·bar^-1) and rejection (from ∼87 to ∼98%). High-flux Cu membranes exhibit superior ductility and electrical conductivity, enabling promising electroactivity. Separation performance and the fouling mechanism were studied under different electrical potentials and ionic strengths. Application of negative polarization into a large-pore (∼2.1 μm) Cu membrane is favorable to not only almost completely reject smaller-sized oil droplets (∼1 μm) but also achieve antifouling and anticorrosion functions. Moreover, surfactants around oil droplets might be redistributed due to electrostatic repulsion, which effectively enhances the steric hindrance effect between neighboring oil droplets, mitigating oil coalescence and consequently membrane fouling. Furthermore, due to the screening effect of surfactants, the presence of low-concentration salts increases the adsorption of surfactants at the oil-water interface, thus preventing oil coalescence via decreasing oil-water interfacial tension. However, under high ionic strengths, the fouling mechanism converts from cake filtration to a complete blocking model due to the reduced electrostatic repulsion between the Cu membrane and oil droplets. This work would provide mechanistic insights into electro-enhanced antifouling for not only oil emulsion separation but also more water treatment applications using rationally designed novel electroresponsive membranes.

Asymmetric Cellulose/Carbon Nanotubes Membrane with Interconnected Pores Fabricated by Droplet Method for Solar-Driven Interfacial Evaporation and Desalination

Solar-driven interfacial water purification and desalination have attracted much attention in environmentally friendly water treatment field. The structure design of the photothermal materials is still a critical factor to improve the evaporation performance such as evaporation rate and energy conversion efficiency. Herein, an asymmetric cellulose/carbon nanotubes membrane was designed as the photothermal membrane via a modified droplet method. Under 1 sun irradiation, the evaporation rate and energy efficiency of pure water can reach up to 1.6 kg m−2 h−1 and 89%, respectively. Moreover, stable reusability and desalination performance made the cellulose/carbon nanotubes membrane a promising photothermal membrane which can be used for solar-driven desalination.

Surface characterization of thin-film composite membranes using contact angle technique: Review of quantification strategies and applications

Thin-film composite (TFC) membranes are the most widely used membranes for low-cost and energy-efficient water desalination processes. Proper control over the three influential surface parameters, namely wettability, roughness, and surface charge, is vital in optimizing the TFC membrane surface and permeation properties. More specifically, the surface properties of TFC membranes are often tailored by incorporating novel special wettability materials to increase hydrophilicity and tune surface physicochemical heterogeneity. These essential parameters affect the membrane permeability and antifouling properties. The membrane surface characterization protocols employed to date are rather controversial, and there is no general agreement about the metrics used to evaluate the surface hydrophilicity and physicochemical heterogeneity. In this review, we surveyed and critically evaluated the process that emerged for understanding the membrane surface properties using the simple and economical contact angle analysis technique. Contact angle analysis allows the estimation of surface wettability, surface free energy, surface charge, oleophobicity, contact angle hysteresis, and free energy of interaction; all coordinatively influence the membrane permeation and fouling properties. This review will provide insights into simplifying the evaluation of membrane properties by contact angle analysis that will ultimately expedite the membrane development process by reducing the time and expenses required for the characterization to confirm the success and the impact of any modification.

Robust zirconia ceramic membrane with exceptional performance for purifying nano-emulsion oily wastewater

While membrane-based oil-water separation has been widely explored, using conventional membranes to treat oily wastewaters remains practically challenging especially when such wastewaters contain more stable nano-sized oil droplets and are of high oil content, and harsh chemical conditions. Herein, we report a novel protocol of efficiently separating both synthetic and real oil nano-emulsions via specially designed robust zirconia membranes. The best-performing zirconia membrane, fabricated at low sintering temperature, has relatively uniform sub-100 nm pores and is underwater superoleophobic. Such zirconia membranes possess not only outstanding separation performance under long-term operation but robust structural stability at harsh conditions. At different cross-flow velocities, a combined model of intermediate pore blocking and cake filtration dominated membrane fouling behavior. Specifically, at high pH value (especially > pH_(IEP)), membrane fouling was effectively mitigated due to a dominant role of electrostatic repulsion interaction at membrane-oil interface. Compared with conventional and commercial ceramic membranes, our zirconia membrane is the first reported in literature that can effectively reject nano-sized oil droplets (∼18 nm) with over 99% rejection. Moreover, the zirconia membrane has also been challenged with real degreasing wastewater with very high oil content (∼4284 mg L^-1) and pH (∼12.4) and delivered consistently high separation performance over many operation cycles.

A critical review of diffusive gradients in thin films technique for measuring organic pollutants: Potential limitations, application to solid phases, and combination with bioassays

Diffusive gradient in thin films (DGT) for organics has received considerable attention for studying the chemical dynamics of various organic pollutants in the environment. This review investigates current limitations of DGT for organics and identifies several research gaps for future studies. The application of a protective outer filter membrane has been recommended for most DGT applications, however, important questions regarding longer lag times due to significant interaction or adsorption of specific groups of compounds on the outer membrane remain. A modified DGT configuration has been developed that uses the diffusive gel as the outer membrane without the use of an extra filter membrane, however use of this configuration, while largely successful, remains limited. Biofouling has been a concern when using DGT for metals; however, effect on the performance of DGT for organics needs to be systemically studied. Storage stability of compounds on intact DGT samplers has been assessed in select studies and that data is synthesized here. DGT has been used to describe the kinetic desorption of antibiotics from soils and biosolids based on the soil/biosolid physical-chemical characteristics, yet applications remain limited and requires further research before wide-scale adoption is recommended. Finally, DGT for organics has been rarely, albeit successfully, combined with bioassays as well as in vivo bioaccumulation studies in zebrafish. Studies using DGT combined with bioassays to predict the adverse effects of environmental mixtures on aquatic or terrestrial biota are discussed here and should be considered for future research.

Janus Membrane with a Dense Hydrophilic Surface Layer for Robust Fouling and Wetting Resistance in Membrane Distillation: New Insights into Wetting Resistance

Although membrane distillation (MD) has been identified as a promising technology to treat hypersaline wastewaters, its practical applications face two prominent challenges: membrane wetting and fouling. Herein, we report a facile and scalable approach for fabricating a Janus MD membrane comprising a dense polyvinyl alcohol (PVA) surface layer and a hydrophobic polyvinylidene fluoride (PVDF) membrane substrate. By testing the Janus membrane in direct contact MD experiments using feeds containing a sodium dodecyl sulfate (SDS) surfactant or/and mineral oil, we demonstrated that the dense Janus membrane can simultaneously resist wetting and fouling. This method represents the simplest approach to date for fabricating MD membranes with simultaneous wetting and fouling resistance. Importantly, we also unveil the mechanism of wetting resistance by measuring the breakthrough pressure and surfactant permeation (through the PVA layer) and found that wetting resistance imparted by a dense hydrophilic layer is attributable to capillary pressure. This new insight will potentially change the paradigm of fabricating wetting-resistant membranes and enable robust applications of MD and other membrane contactor processes facing challenges of pore wetting or/and membrane fouling.

Behavior of Sliding Angle as Function of Temperature Difference between Droplet and Superhydrophobic Coating for Aircraft Ice Protection Systems

A hybrid anti-/de-icing system combining a superhydrophobic coating and an electrothermal heater is an area of active research for aircraft icing prevention. The heater increases the temperature of the interaction surface between impinging droplets and an aircraft surface. One scientific question that has not been studied in great detail is whether the temperatures of the droplet and the surface or the temperature difference between the two dominate the anti-/de-icing performance. Herein, this scientific question is experimentally studied based on the mobility of a water droplet over a superhydrophobic coating. The mobility is characterized by the sliding angle between the droplet and the coating surface. It was found that the temperature difference between the droplet and the coating surface has a higher impact on the sliding angle than their individual temperatures.

Porous Layer-by-Layer Films Assembled Using Polyelectrolyte Blend to Control Wetting Properties

Porous layer-by-layer (LbL) films have been employed for the implementation of superwetting surfaces, but they are limited to the LbL films consisting of only two oppositely charged polyelectrolytes. In this study, LbL films were assembled using a cationic polymer blend of branched poly(ethylene imine) (BPEI) and poly(allylamine hydrochloride) (PAH), and anionic poly(acrylic acid); they were then acid-treated at pH 1.8-2.0 to create a porous structure. The films of 100% BPEI exhibited a relatively smooth surface, whereas those of the 100% PAH exhibited porous surfaces. However, various surface morphologies were obtained when BPEI and PAH were blended. When coated with fluorinated silane, films with 50% and 100% PAH exhibited relatively higher water contact angles (WCAs). In particular, films with 50% PAH exhibited the highest WCA of 140-150° when treated at pH 1.8. These fluorinated films were further infused with lubricant oil to determine their feasibility as slippery surfaces. The water and oil sliding angles were in the range of 10-20° and 5-10°, respectively. Films prepared with the BPEI/PAH blend showed lower water slide angles than those prepared with 100% BPEI or PAH. Acid treatment of LbL films assembled using a polyelectrolyte blend can effectively control surface morphologies and can potentially be applied in superwetting.

Straightforward Patterning of Functional Polymers by Sequential Nanosecond Pulsed Laser Irradiation

Laser-based methods have demonstrated to be effective in the fabrication of surface micro- and nanostructures, which have a wide range of applications, such as cell culture, sensors or controlled wettability. One laser-based technique used for micro- and nanostructuring of surfaces is the formation of laser-induced periodic surface structures (LIPSS). LIPSS are formed upon repetitive irradiation at fluences well below the ablation threshold and in particular, linear structures are formed in the case of irradiation with linearly polarized laser beams. In this work, we report on the simple fabrication of a library of ordered nanostructures in a polymer surface by repeated irradiation using a nanosecond pulsed laser operating in the UV and visible region in order to obtain nanoscale-controlled functionality. By using a combination of pulses at different wavelengths and sequential irradiation with different polarization orientations, it is possible to obtain different geometries of nanostructures, in particular linear gratings, grids and arrays of nanodots. We use this experimental approach to nanostructure the semiconductor polymer poly(3-hexylthiophene) (P3HT) and the ferroelectric copolymer poly[(vinylidenefluoride-co-trifluoroethylene] (P(VDF-TrFE)) since nanogratings in semiconductor polymers, such as P3HT and nanodots, in ferroelectric systems are viewed as systems with potential applications in organic photovoltaics or non-volatile memories.

Silanization of a Metal-Polyphenol Coating onto Diverse Substrates as a Strategy for Controllable Wettability with Enhanced Performance to Resist Acid Corrosion

Wettability is a crucial characteristic of materials that plays a vital role in surface engineering. Surface modification is the key to changing the wettability of materials, and a simple and universal modification approach is being extensively pursued by researchers. Recently, metal-phenolic networks (MPNs) have been widely studied because they impart versatility and functionality in surface modification. However, an MPN is not stable for long periods, especially under acidic conditions, and is susceptible to pollution by invasive species. Spurred by the versatility of MPNs and various functionalities achieved by silanization, we introduce a general strategy to fabricate functionally stable coatings with controllable surface wettability by combining the two methods. The formation process of MPN and silane-MPN coatings was characterized by spectroscopic ellipsometry (SE), UV-visible-near-infrared (UV-vis-NIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM), water contact angle (WCA), etc. We found that the stability of the MPN was greatly enhanced after silanization, which is attributed to the cross-linking effect that occurs between silane and the MPN, namely, the cross-linking protection produced in this case. Additionally, the wettability of an MPN can be easily changed through our strategy. We trust that our strategy can further extend the applications of MPNs and points toward potential prospects in surface modification.