Removal Mechanisms of Phosphate by Lanthanum Hydroxide Nanorods: Investigations using EXAFS, ATR-FTIR, DFT, and Surface Complexation Modeling Approaches

Lanthanum-modified pyroaurite as a geoengineering tool to simultaneously sink Microcystis cyanobacteria and immobilize phosphorus in eutrophic water

Excessive phosphorus (P) in eutrophic water induces cyanobacterial blooms that aggravate the burden of in-situ remediation measures. In order to ensure better ecological recovery, Flock & Lock technique has been developed to simultaneously sink cyanobacteria and immobilize P but requires a combination of flocculent and P inactivation agent. Here we synthesized a novel lanthanum-modified pyroaurite (LMP), as an alternative for Flock & Lock of cyanobacteria and phosphorus at the background of rich humic acid and suspended solids. LMP shows a P adsorption capacity of 36.0 mg/g and nearly 100 % removal of chlorophyll-a (Chl-a), turbidity, UV254 and P at a dosage (0.3 g/L) much lower than the commercial analogue (0.5 g/L). The resultant sediment (98.2 % as immobile P) exhibits sound stability without observable release of P or re-growth of cyanobacteria over a 50-day incubation period. The use of LMP also constrains the release of toxic microcystins to 1.4 μg/L from the sunk cyanobacterial cells, outperforming the commonly used polyaluminum chloride (PAC). Similar Flock & Lock efficiency could also be achieved in real eutrophic water. The outstanding Flock & Lock performance of LMP is attributable to the designed La modification. During LMP treatment, La acts as not only a P binder by formation of LaPO4, but also a coagulant to create a synergistic effect with pyroaurite. The controlled hydrolysis of surface La(III) over pyroaurite aided the possible formation of La(III)-pyroaurite networking structure, which significantly enhanced the Flock & Lock process through adsorption, charge neutralization, sweep flocculation and entrapment. In the end, the preliminary economic analysis is performed. The results demonstrate that LMP is a versatile and cost-effective agent for in-situ remediation of eutrophic waters.

Intertwined role of mechanism identification by DFT-XAFS and engineering considerations in the evolution of P adsorbents

Adsorption method exhibits promising potential in effectively removal of phosphate from wastewater, yet it faces tremendous challenges in practical application. Limited comprehension of adsorption mechanisms and the lack of evaluation method for scaling up application are the two main obstacles. To fully realize the practical application of P adsorbents, we reviewed advanced tools, including density functional theory (DFT) and/or X-ray absorption fine structure (XAFS) to elucidate mechanisms, underscored the significance of thermodynamics and kinetics in engineering design, and proposed strategies for regenerating and reusing P adsorbents. Specifically, we delved into the utilization of DFT and XAFS to gain insights into adsorption mechanisms, focusing on active site verification and molecular interaction configurations. Additionally, we explored precise calculation methods for adsorption thermodynamics and adsorption kinetics, encompassing thermodynamic equilibrium constants, reactor selection, and the regeneration, recovery, and disposal of P adsorbents. Our comprehensive review aims to serve as a guiding light in advancing the development of highly efficient P adsorbents for engineering applications.

Hydrothermally Stimulated Molecular Interfaces for Augmented Electron Delocalization in Wet-Chemical Phosphorus Recovery from Incineration Ash of Sewage Sludge

Wet-chemically recovering phosphorus (P) from sewage sludge incineration ash (SSIA) has already become a global initiative to address P deficit, but effectively isolating P from these accompanying metals (AMs) through adsorption in a SSIA-derived extract remains elusive. Here, we devised a hydrothermal stimulus-motivated thermodynamic and kinetic enhancement to gain anionic ethylenediaminetetraacetic acid (EDTA) molecular interfaces for AM enclosure to resolve this conundrum. A new dosage rule based on the EDTA coordination ratio with AMs was established for the first time. Upon hydrothermal extraction at 140 °C for 1 h, the P extraction efficiency reached 96.7% or higher for these obtained SSIA samples, and then exceptional P sequestration from these EDTA-chelated AMs was realized by the peculiar lanthanum (La)-based nanoadsorbent (having 188.86 mg P/g adsorbent at pH ∼ 3.0). Relevant theoretical calculations unraveled that these delocalized electrons of tetravalent EDTA molecules boosted the enclosure of liberated AMs, thereby entailing a substantially increased negative adsorption energy (-408.7 kcal/mol) of P in the form of H2PO4- through intruding lattice-edged carbonates to coordinate La with monodentate mononuclear over LaCO5(1 0 1). This work highlights the prospect of molecular adaptation of these common extractants in wet-chemical P recovery from various P-included wastes, further sustaining global P circularity.

Monodispersed and Organic Amine Modified La(OH)3 Nanocrystals for Superior Advanced Phosphate Removal

Advanced phosphate removal is critical for alleviating the serious and widespread aquatic eutrophication, strongly depending on the development of superior adsorption materials to overcome low chemical affinity and sluggish mass transfer at low phosphate concentrations. Herein, the first synthesis of monodispersed and organic amine modified lanthanum hydroxide nanocrystals (OA-La(OH)3) for advanced phosphate removal by modulating inner Helmholtz plane (IHP), is reported. These OA-La(OH)3 nanocrystals with positively charged surfaces and abundant exposed La sites exhibit specific affinity toward phosphate, delivering a maximum adsorption capacity of 168 mg P g⁻1 and a wide pH adaptability from 3.0 to 11.0, as well as a robust anti-interference performance, far surpassing those of documented phosphate removal materials. The superior phosphate removal performance of OA-La(OH)3 is attributed to its protonated organic amine in IHP, which enhances the electrostatic attraction around the adsorbent-solution interface. Impressively, OA-La(OH)3 can treat ≈5 000 and ≈3 200 bed volumes of simulated and real phosphate-containing wastewater to below extremely strict standard (0.1 mg L⁻1) in a fixed-bed adsorption mode, exhibiting great potential for advanced phosphate removal. This study offers a facile modification strategy to improve phosphate removal performance of nanoscale adsorbents, and sheds light on the structure-reactivity relationship of La-based materials.

Enhanced removal of phosphate from aqueous solutions by oxygen vacancy-rich MgO microspheres: Performance and mechanism

The efficient removal of phosphate from water environments was extremely significant to control eutrophication of water bodies and prevent further deterioration of water quality. In this study, oxygen vacancy-rich magnesium oxide (OV-MgO) microspheres were synthesized by a simple solvothermal method coupling high-temperature calcination. The effects of adsorbent dosage, contact time, initial pH and coexisting components on phosphate adsorption performance were examined. The physicochemical properties of OV-MgO microspheres and the phosphate removal mechanisms were analyzed by various characterization techniques. The maximum adsorption capacity predicted by the Sips isotherm model was 379.7 mg P/g for OV-MgO microspheres. The phosphate adsorption in this study had a fast adsorption kinetics and a high selectivity. OV-MgO microspheres had a good acid resistance for phosphate adsorption, but their adsorption capacity decreased under alkaline conditions. The electrostatic attraction, ligand exchange, surface precipitation, inner-sphere surface complexation and oxygen vacancy capture were mainly responsible for efficient removal of phosphate from aqueous solutions. This study probably promoted the development of oxygen vacancy-rich metal (hydr)oxides with potential application prospects.

Nano La(OH)3 modified lotus seedpod biochar: A novel solution for effective phosphorus removal from wastewater

Effective removal of phosphorus from water is crucial for controlling eutrophication. Meanwhile, the post-disposal of wetland plants is also an urgent problem that needs to be solved. In this study, seedpods of the common wetland plant lotus were used as a new raw material to prepare biochar, which were further modified by loading nano La(OH)3 particles (LBC-La). The adsorption performance of the modified biochar for phosphate was evaluated through batch adsorption and column adsorption experiments. Adsorption performance of lotus seedpod biochar was significantly improved by La(OH)3 modification, with adsorption equilibrium time shortened from 24 to 4 h and a theoretical maximum adsorption capacity increased from 19.43 to 52.23 mg/g. Moreover, LBC-La maintained a removal rate above 99% for phosphate solutions with concentrations below 20 mg/L. The LBC-La exhibited strong anti-interference ability in pH (3-9) and coexisting ion experiments, with the removal ratio remaining above 99%. The characterization analysis indicated that the main mechanism is the formation of monodentate or bidentate lanthanum phosphate complexes through inner sphere complexation. Electrostatic adsorption and ligand exchange are also the mechanisms of LBC-La adsorption of phosphate. In the dynamic adsorption experiment of simulated wastewater treatment plant effluent, the breakthrough point of the adsorption column was 1620 min, reaching exhaustion point at 6480 min, with a theoretical phosphorus saturation adsorption capacity of 6050 mg/kg. The process was well described by the Thomas and Yoon-Nelson models, which indicated that this is a surface adsorption process, without the internal participation of the adsorbent.

Nanoconfinement boosts affinity of hydrated zirconium oxides to arsenate: Surface complexation modeling study

Nanoscale hydrated zirconium oxide (HZO) holds great potential in groundwater purification due to its ability to form inner-sphere coordination with arsenate. Despite being frequently used, especially as encapsulations in host materials for practical application in water treatment, the adsorption mechanisms of solutes on HZO are not appropriately explored, in particular for arsenate adsorption. In this study, we investigated the Zr-As coordination configuration and identified the most credible Zr-As configuration using surface complexation modeling (SCM), XPS and FT-IR analysis. The corresponding intrinsic coordination constants (Kintr) values was calculated by SCM, and the nanoconfinement effects were distinguished by comparing bare HZO with the HZO nanoparticles (NPs) encapsulated inside the strongly basic anion exchanger D201. Potentiometric titration suggests that the surface Zirconium hydroxyl groups (≡ZrOH) mainly exist in protonated form (≡ZrOH2+). Batch adsorption experiments demonstrate that the D201 hosts could adsorb As(V) through ion exchange by the quaternary ammonium groups under the low ionic strength (≤0.01 M NaNO3) and at pH > 6. The nanocomposite (HZO@D201) exhibits a higher adsorption capacity in a wide range of pH (3-10) and ionic strength (0.001-0.1 M NaNO3) than bare HZO. SCM simulations reveal that the coordination configuration of diprotonated monodentate mononuclear (MM-H2) dominates at pH 3-6, while deprotonated bidentate binuclear (BB-H0) dominates at pH > 7. For each configuration, the intrinsic coordination constants (Kintr) of HZO@D201 (10-0.66 and 10-16.10, respectively) are significantly higher than those of bare HZO (10-12.24 and 10-44.42, respectively), indicating a superior chemical bonding affinity caused by nanoconfinement. The obtained Kintr values are used to predict arsenate adsorption isotherms in pH 3 and 9, and the results align with the SCM simulation outcomes. This study may offer a feasible method for investigating the nanoconfinement effect of emerging nanocomposite adsorbents from a thermodynamic perspective, and provide reference coordination equilibrium constants of HZO for research and practical application.

Bimetallic capture sites on porous La/Bi hydroxyl double salts for efficient phosphate adsorption: Multiple active centers and excellent selective properties

The rapid development of modern agriculture aggravated water eutrophication. Therein, efficient and selective removal of phosphorus in water is the key to alleviating eutrophication. It is well known that lanthanum (La)-based material is a kind of outstanding phosphorus-locking agent. Therefore, improving the property of La-based adsorbents is a hot topic in this field. Herein, novel porous hydroxyl double salts (La/Bi-HDS) with bimetallic capture sites were prepared. The experimental result shows that La/Bi-HDS could maintain the high removal rate in the solution with a higher concentration of competing ions and the maximum P adsorption quantity of La/Bi-HDS attains 168.12 mg/g. Mechanistic studies supported by density functional theory (DFT) calculation demonstrate that introducing Bi3+ optimizes the electronic structure of La, reducing adsorption energy. In addition, the surface analysis shows that the introduction of Bi, which increases the pore size and volume of the material, improves the utilization efficiency of the active site. In a word, the introduction of Bi element as a strategy of killing two birds with one stone successfully improved the performance of La-based adsorbent. It provided a new direction for developing an efficient phosphorus-locking agent.

Optimization of Electron Transport Pathway: A Novel Strategy to Solve the Photocorrosion of Ag-Based Photocatalysts

Although Ag-containing photocatalysts exhibit excellent photocatalytic ability, they present great challenges owing to their photocorrosion and ease of reduction. Herein, an electron acceptor platform of Ag2O/La(OH)3/polyacrylonitrile (PAN) fiber was constructed using a heterojunction strategy and electrospinning technology to develop a novel photocatalytic membrane with a redesigned electron transport pathway. Computational and experimental results demonstrate that the optimized electron transport pathway included intercrystal electron transfer induced by the La-O bond between Ag2O and La(OH)3 as well as electron transfer between the catalyst crystal and electrophilic PAN membrane interface. In addition, the photocatalytic performance of the Ag2O/La(OH)3 membrane for tetracycline (TC) removal was still above 97% after five photocatalytic reaction cycles. Furthermore, the carrier life was greatly extended. Mechanistic study revealed that photogenerated holes on the Ag2O/La(OH)3 membrane were the main reactive species in TC degradation. Overall, this study proposes a novel electron transport pathway strategy that effectively solves the problems of photocatalyst photocorrosion and structural instability.

Towards low energy-carbon footprint: Current versus potential P recovery paths in domestic wastewater treatment plants

With the unprecedented exhaustion of natural phosphorus (P) resource and the high eutrophication potential of the associated-P discharge, P recovery from the domestic wastewater is a promising way and has been putting on agenda of wastewater industry. To address the concern of P resource recovery in an environmentally sustainable way is indispensable especially in the carbon neutrality-oriented wastewater treatment plants (WWTPs). Therefore, this review aims to offer a critical view and a holistic analysis of different P removal/recovery process in current WWTPs and more P reclaim options with the focus on the energy consumption and greenhouse gas (GHG) emission. Unlike P mostly flowing out in the planned/semi-planned P removal/recovery process in current WWTPs, P could be maximumly sequestered via the A-2B- centered process, direct reuse of P-bearing permeate from anaerobic membrane bioreactor, nano-adsorption combined with anaerobic membrane and electrochemical P recovery process. The A-2B- centered process, in which the anaerobic fixed bed reactor was designated for COD capture for energy efficiency while P was enriched and recovered with further P crystallization treating, exhibited the lowest specific energy consumption and GHG emission on the basis of P mass recovered. P resource management in WWTPs tends to incorporate issues related to environmental protection, energy efficiency, GHG emission and socio-economic benefits. This review offers a holistic view with regard to the paradigm shift from "simple P removal" to "P reuse/recovery" and offers in-depth insights into the possible directions towards the P-recovery in the "water-energy-resource-GHG nexus" plant.

Thermal Air Oxidation-Mediated Synchronous Coordination and Carbonation of Lanthanum on Biochar toward Phosphorus Adsorption from Wastewater

Biochar has attracted increasing attention as the sustainable and structure-tunable carrier for lanthanum (La) species for diverse applications. Carbonated La species possesses a higher biocompatibility and a lower leaching potential than other commonly used La species, while less attention is paid on the application of carbonated La in phosphorus (P) adsorption. Herein, thermal air oxidation (TAO) was applied as a novel strategy for synchronously tuning the coordination environment and chemical species of La on biochar surface. The results demonstrated that TAO induced the coordination of La with oxidation-generated oxygenated functional groups (OFGs) and carbonation of La species by the oxidation-generated CO2 on the biochar surface. The batch adsorption results showed that the Qm of resultant biochar remarkably increased from 68.92 to 132.49 mg/g at 1 g/L dosage. It also showed a robust adsorption stability in pH 2-6, a strong resistance to the co-existing Cl-, SO42-, NO3-, CO32-, or HCO3-, a stable adsorption recyclability, and an ultralow La leaching potential. The P adsorption was dominated by ligand exchange-induced inner-sphere complexation. In practical swine wastewater, the resultant biochar composite (1 g/L) removed 99.87% of P from 92.3 to 0.12 mg/L at a practical pH of 7.12. The density functional theory calculation further revealed the significant role of the binding of carbonated La by the biochar surface OFGs in reducing the P adsorption energies, indicating the synergism between the oxygenated biochar carrier and the carbonated La in P adsorption. Finally, this study provided a novel route to synchronously tune the coordination environment and chemical species of La on biochar via a facile TAO process for high-efficient P adsorption from wastewater.

Adsorption effects and mechanisms of phosphorus by nanosized laponite

Phosphorus (P), an important macroelement for crops, may be lost into water systems by human activities and subsequently cause serious environmental problems such as eutrophication. Thus, the recovery of P from wastewater is essential. P can be adsorbed and recovered from wastewater using many natural, environmentally friendly clay minerals, however the adsorption ability is limited. Here we applied a synthesis nanosized clay mineral, laponite, to evaluate the P adsorption ability and molecular mechanisms of the adsorption process. We apply X-ray Photoelectron Spectroscopy (XPS) to observe the adsorption of inorganic phosphate onto laponite, and then measure the adsorption content of phosphate by laponite via batch experiments in different solution conditions, including pH, ionic species and concentrations. Then the molecular mechanisms of adsorption are analyzed by Transmission Electron Microscopy (TEM) and molecular modeling using Density Functional Theory (DFT). The results show that phosphate adsorbs to the surface and interlayer of laponite via hydrogen bonding, and the adsorption energies of the interlayer are greater than those of the surface. These bulk solution and molecular-scale results in a model system may provide new insights into the recovery of phosphorus by nanosized clay, with possible environmental engineering applications for P-pollution control and sustainable utilization of P sources.

Effect of capping mode on control of phosphorus release from sediment by lanthanum hydroxide

The use of in situ active capping to control phosphorus release from sediment has attracted more and more attentions in recent years. It is important to identify the effect of capping mode on the control of phosphorus release from sediment by the in situ active capping method. In this study, the impact of capping mode on the restraint of phosphorus migration from sediment into overlying water (OW) by lanthanum hydroxide (LH) was studied. Under no suspended particulate matter (SPM) deposition condition, LH capping effectively restrained the liberation of endogenous phosphorus into OW during anoxia, and the inactivation of diffusive gradient in thin film-unstable phosphorus (UP_DGT) and mobile phosphorus (P_Mobile) in the topmost sediment served as a significant role in the restraint of endogenous phosphorus migration into OW by LH capping. Under no SPM deposition, although the transformation of capping mode from the single high dose capping to the multiple smaller doses capping had a certain negative impact on the restraint efficiency of endogenous phosphorus liberation to OW by LH in the early period of application, it increased the stability of phosphorus in the static layer in the later period of application. Under SPM deposition condition, LH capping had the capability to mitigate the risk of endogenous phosphorus liberation into OW under anoxia conditions, and the inactivation of UP_DGT and P_Mobile in the topmost sediment was a significant mechanism for the control of sediment phosphorus liberation into OW by LH capping. Under SPM deposition condition, the change in the covering mode from the one-time high dose covering to the multiple smaller doses covering decreased the efficiency of LH to limit the endogenous phosphorus transport into OW in the early period of application, but it increased the performance of LH to restrain the sedimentary P liberation during the later period of application. The results of this work suggest that the multiple LH capping is a promising approach for controlling the internal phosphorus loading in freshwater bodies where SPM deposition often occurs in the long run.

Graphene oxide-based dendritic adsorbent for the excellent capturing of platinum group elements

Herein, we report amino functionalized thermally stable graphene oxide-based dendritic adsorbent (GODA) with the highest sorption capacity ever recorded for platinum group elements (PGEs), including platinum (Pt(IV), PtCl₆^2-) and palladium (Pd(II), PdCl₄^2-), from highly acidic aqueous solutions. The GODA was designed and synthesized to have fully ionized amine binding sites and was characterized in detail. The detail batch adsorption experiment along with kinetic, isotherm, and thermodynamic studies were carried out to investigate the adsorption efficacy of GODA. For both Pt(IV) and Pd(II), the experimental data are more accurately fitted with the pseudo-second-order and the intraparticle diffusion kinetic models and Langmuir isotherm model as compared to the pseudo-first-order kinetic model and Freundlich and Temkin isotherm models, respectively. The material showed the highest ever adsorption capacities of 827.8 ± 27.7 mg/g (4.24 ± 0.00 mmol/g) and 890.7 ± 29.1 mg/g (8.37 ± 0.00 mmol/g) for Pt(IV) and Pd(II), respectively, at pH 1. The adsorption equilibriums were achieved within 70 min and 65 min for Pt(IV) and Pd(II), respectively. The thermodynamic parameters indicate that the adsorptions of both metals are spontaneous. The binding mechanisms are considered to be electrostatic interactions, hydrogen bonding, cationic-π bonding, and surface complexation between the sorbent and the sorbates. Furthermore, the as-prepared GODA exhibited high thermal stability and significant acid-resistance at pH 1. The GODA demonstrated excellent regeneration and reusability for Pt(IV) and Pd(II) over five adsorption/desorption cycles, indicating its excellence in practical applications.

Phosphate interactions with iron-titanium oxide composites: Implications for phosphorus removal/recovery from wastewater

Understanding the interactions between phosphate (P) and mineral adsorbents is critical for removing and recovering P from wastewater, especially in the presence of both cationic and organic components. To this end, we investigated the surface interactions of P with an iron-titanium coprecipitated oxide composite in the presence of Ca (0.5-3.0 mM) and acetate (1-5 mM), and quantified the molecular complexes and tested the possible removal and recovery of P from real wastewater. A quantitative analysis of P K-edge X-ray absorption near edge structure (XANES) confirmed the inner-sphere surface complexation of P with both Fe and Ti, whose contribution to P adsorption relies on their surface charge determined by pH conditions. The effects of Ca and acetate on P removal were highly pH-dependent. At pH 7, Ca (0.5-3.0 mM) in solution significantly increased P removal by 13-30% by precipitating the surface-adsorbed P, forming hydroxyapatite (14-26%). The presence of acetate had no obvious influence on P removal capacity and molecular mechanisms at pH 7. At pH 4, the removal amount of P was not obviously affected by the presence of Ca and acetate. However, acetate and high Ca concentration jointly facilitated the formation of amorphous FePO₄ precipitate, complicating the interactions of P with Fe-Ti composite. In comparison with ferrihydrite, the Fe-Ti composite significantly decreased the formation of amorphous FePO₄ probably by decreasing Fe dissolution due to the coprecipitated Ti component, facilitating further P recovery. An understanding of these microscopic mechanisms can lead to the successful use and simple regeneration of the adsorbent to recover P from real wastewater.

Direct Atomic-Scale Insight into the Precipitation Formation at the Lanthanum Hydroxide Nanoparticle/Solution Interface

Understanding precipitation formation at lanthanum hydroxide (La(OH)₃) nanoparticle-solution interfaces plays a crucial role in catalysis, adsorption, and electrochemical energy storage applications. Liquid-phase transmission electron microscopy enables powerful visualization with high resolution. However, direct atomic-scale imaging of the interfacial metal (hydro)oxide nanostructure in solutions has been a major challenge due to their beam-driven dissolution. Combining focused ion beam and aberration-corrected high-angle annular dark-field scanning transmission electron microscopy, we present an atomic-scale study of precipitation formation at La(OH)₃ nanoparticle interfaces after reaction with phosphate. The structure transformation is observed to occur at high- and low-crystalline La(OH)₃ nanoparticle surfaces. Low-crystalline La(OH)₃ mostly transformed and high-crystalline ones partly converted to LaPO₄ precipitations on the outer surface. The long-term structure evolution shows the low transformation of high-crystalline La(OH)₃ nanoparticles to LaPO₄ precipitation. Because precipitation at solid-solution interfaces is common in nature and industry, these results could provide valuable references for their atomic-scale observation.

Preparation and Characterization of an Invasive Plant-Derived Biochar-Supported Nano-Sized Lanthanum Composite and Its Application in Phosphate Capture from Aqueous Media

Invasive plants pose a great threat to natural ecosystems owing to their rapid propagation and spreading ability in nature. Herein, a typical invasive plant, Solidago canadensis, was chosen as a novel feedstock for the preparation of nano-sized lanthanum-loaded S. canadensis-derived biochar (SCBC-La), and its adsorption performance for phosphate removal was evaluated by batch adsorption experiment. The composite was characterized by multiple techniques. Effects of parameters, such as the initial concentration of phosphate, time, pH, coexisting ions, and ionic strength, were studied on the phosphate removal. Adsorption kinetics and isotherms showed that SCBC-La shows a faster adsorption rate at a low concentration and SCBC-La exhibits good La utilization efficiency than some of the reported La-modified adsorbents. Phosphate can be effectively removed over a relatively wide pH of 3-9 because of the high pH _pzc of SCBC-La. Furthermore, the SCBC-La shows a strong anti-interference capability in terms of pH value, coexisting ions, and ionic strength, exhibiting a highly selective capacity for phosphate removal. Additionally, Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) measurements reveal that hydroxyl groups on the surface of SCBC-La were replaced by phosphate and manifest the reversible transformation between La(OH)₃ and LaPO₄. Considering its high adsorption capacity and excellent selectivity, SCBC-La is a promising material for preventing eutrophication. This work gives a new method of pollution control with waste treatment since the invasive plant (S. canadensis) is converted into biochar-based nanocomposite for effective removal of phosphate to mitigate eutrophication.

Green and Efficient Al-Doped LaFexAl1-xO3 Perovskite Oxide for Enhanced Phosphate Adsorption with Creation of Oxygen Vacancies

La-based metal oxide materials are environmentally friendly and show promise for phosphate adsorption. A series of Al-doped perovskite oxides, such as LaFe_xAl_1-xO₃, were prepared using a facile citric acid-assisted sol-gel method. The characterization results demonstrated that with optimized Al doping, there was a significant increase in the specific surface area and increased defect content of perovskite oxide LaFe_xAl_1-xO₃. Adsorption experiments showed that the performance of phosphate removal by LaFe_xAl_1-xO₃ was largely enhanced due to the improved adsorption capacity, which is maximum eight times higher compared with control perovskites prepared under neutral conditions. The mass transfer rate for adsorption was considerably boosted with phosphate removal within the initial 15 min. Spectroscopy analysis and density functional theory calculation results showed that the process of phosphate removal by the Al-doped perovskite oxides LaFe_xAl_1-xO₃ involved electrostatic interactions, an inner-sphere complex, and surface oxygen vacancies, among which the creation of oxygen vacancies caused by the Al doping was the predominant mechanism for reducing the bonding barrier during adsorption and generating adsorption sites. The results enable the development of a green and efficient perovskite adsorbent with a La-based perovskite material for phosphorus removal.

One-pot synthesis of novel flower-like LaCO3OH adsorbents for efficient scavenging of phosphate from wastewater

Phosphorus removal from wastewater has been considered as an effective method to control eutrophication and mitigate phosphorus deficiency. Phosphate adsorption using lanthanum-based materials has awakened much attention and triggered extensive research. In this study, novel flower-like LaCO₃OH materials were synthesized via a one-step hydrothermal method and evaluated for phosphate removal from wastewater. The adsorbent with flower-like structures prepared at the hydrothermal reaction time of 4.5 h (BLC-4.5) exhibited the optimum adsorption performance. BLC-4.5 had a rapid removal rate with more than 80% of the saturated adsorbed phosphate removed within 20 min. Furthermore, the maximum phosphate adsorption capacity of BLC-4.5 was as high as 228.5 mg/g. Notably, the La leaching amount of BLC-4.5 was negligible in the pH range of 3.0-11.0. BLC-4.5 outperformed most of the reported La-based adsorbents in terms of removal rate, adsorption capacity, and La leaching amount. Moreover, BLC-4.5 had broad pH adaptability (3.0-11.0) and high selectivity for phosphate. BLC-4.5 also displayed excellent phosphate removal efficiency in actual wastewater and great recyclability. The potential adsorption mechanisms of phosphate on BLC-4.5 were precipitation, electrostatic attraction, and inner-sphere complexation via ligand exchange. This study demonstrates that the newly developed flower-like BLC-4.5 reported here is a promising adsorbent for the effective treatment of phosphate in wastewater.

Iron Vacancy Accelerates Fe(II)-Induced Anoxic As(III) Oxidation Coupled to Iron Reduction

Chemical oxidation of As(III) by iron (Fe) oxyhydroxides has been proposed to occur under anoxic conditions and may play an important role in stabilization and detoxification of As in subsurface environments. However, this reaction remains controversial due to lack of direct evidence and poorly understood mechanisms. In this study, we show that As(III) oxidation can be facilitated by Fe oxyhydroxides (i.e., goethite) under anoxic conditions coupled with the reduction of structural Fe(III). An excellent electron balance between As(V) production and Fe(III) reduction is obtained. The formation of an active metastable Fe(III) phase at the defective surface of goethite due to atom exchange is responsible for the oxidation of As(III). Furthermore, the presence of defects (i.e., Fe vacancies) in goethite can noticeably enhance the electron transfer (ET) and atom exchange between the surface-bound Fe(II) and the structural Fe(III) resulting in a two time increase in As(III) oxidation. Atom exchange-induced regeneration of active goethite sites is likely to facilitate As(III) coordination and ET with structural Fe(III) based on electrochemical analysis and theoretical calculations showing that this reaction pathway is thermodynamically and kinetically favorable. Our findings highlight the synergetic effects of defects in the Fe crystal structure and Fe(II)-induced catalytic processes on anoxic As(III) oxidation, shedding a new light on As risk management in soils and subsurface environments.

Novel oxymagnesite/green rust nanohybrids for selective removal and slow release of phosphate in water

The new paradigm in wastewater treatment demands to change traditional pollutants removal into resource recovery, especially for non-renewable P resources, effectively recovering phosphate from wastewater and reutilizing it as a nutrient is crucial to P sustainable utilization and P-related pollution control. The nanomaterial-based adsorption technology for P recovery from wastewater is becoming a research hotspot due to its high efficiency and selectivity. Herein, to recover aqueous phosphate, we developed novel oxymagnesite/green rust (OMGR) nanohybrids by a one-pot hydrothermal method. Green rust nanoparticles dispersed on the highly reactive oxymagnesite (MgO2MgCO₃) nanosheets could achieve efficient recovery and reuse of P. The volume ratio of water to ethylene glycol played an important role in the preparation of OMGR. The OMGR possessed an excellent selectivity of phosphate removal in the presence of multi-anions and wide pH adaptability in 4.0-10.0. The formation of MgP nanocrystals and the inner-sphere FeOP complexes via ligand exchange contributed to the selective removal of P by OMGR, and the removal capacity reached 141 mg P^.g^-1. The process of phosphate removal by OMGR was spontaneously endothermic and controlled by the intraparticle and boundary layer diffusion. Most importantly, the high bioavailable P (127 mg^.g^-1) of P-loaded OMGR had a persistent release behavior regulated by dissolution and diffusion, indicating that the P-loaded OMGR can act as a slow-release P-fertilizer. The findings provide a green and eco-friendly approach to realizing P resource recovery and reuse for phosphate-containing wastewaters.

Facet-Dependent Atomic Distances Shape Vanadate Adsorption Complexes on Hematite Nanocrystals

The environmental fate of vanadate (V(V)) is significantly influenced by iron oxide nanocrystals through adsorption. Nevertheless, the underlying driving force controlling V(V) adsorption on hematite (Fe2O3) facets is poorly understood. Herein, V(V) adsorption on the {001}, {110}, and {214} Fe2O3 facets was explored using batch adsorption experiments, spectroscopic studies, and density functional theory (DFT) calculations. Adsorption experiments suggested that the order of V(V) adsorption capacity followed {001} > {110} > {214}. However, the affinity of V(V) to the {001} facet was the weakest, as evidenced by its least resistance to phosphate and sulfate competition. Our extended X-ray absorption fine structure (EXAFS) study indicated the formation of the inner-sphere monodentate mononuclear (1V) complex on the {001} facet and bidentate corner-sharing (2C) complexes on the {110} and {214} facets. Density functional theory (DFT) calculations showed the 1V complex is preferable when the adjacent Fe-Fe atomic distance is significantly larger than the O-O atomic distance of V(V). Otherwise, the 2C complex is formed if the distance is comparable. This determining factor in surface complex formation can be safely extended to other oxyanions that the compatibility in the atomic distance of Fe-Fe on Fe2O3 facets and O-O in oxyanions shapes the surface complex. The molecular-level understanding of the facet-dependent adsorption mechanism provides the basis for the design and application of oxyanion adsorbents.

Microwave- and ultrasonic-assisted synthesis of 2D La-based MOF nanosheets by coordinative unsaturation degree to boost phosphate adsorption

The metal or metal clusters and organic ligands are relevant to the selectivity and performance of phosphate removal in MOFs, and the electron structure, chemical characteristics, and preparation method also affect efficiency and commercial promotion. However, few reports focus on the above, especially for 2D MOF nanomaterials. In this work, two 2D Ln-TDA (Ln = La, Ce) nanosheets assembled via microwave- and ultrasonic-assisted methods are employed as adsorbents for phosphate (H2PO4 -, HPO4 2-) removal for the first time. Their microstructure and performance were characterized using XRD, TEM, SEM, AFM, FTIR, zeta potential, and DFT calculations. The prepared 2D Ln-TDA (Ln = La, Ce) nanosheets exposed more adsorption sites and effectively reduced the restrictions of mass transfer. Based on this, the Langmuir model was employed to estimate the maximum adsorption capacities of the two kinds of nanosheets, which reached 253.5 mg g-1 and 259.5 mg g-1, which are 553 times and 3054 times larger than those for bulk Ln-TDA (Ln = La, Ce), respectively. Additionally, the kinetic data showed that the adsorption equilibrium time is fast, approximately 15 min by the pseudo-second-order model. In addition, the prepared products not only have a wide application range (pH = 3-9) but also offer eco-safety in terms of residuals (no Ln leak out). Based on the XPS spectra, FTIR spectra and DFT calculations, the main adsorption mechanisms included ligand exchange and electrostatic interactions. This new insight provides a novel strategy to prepare 2D MOF adsorbents, achieving a more eco-friendly method (microwave- and ultrasonic-assisted synthesis) for preparing 2D Ln-based MOF nanosheets by coordinative unsaturation to boost phosphate adsorption.

Phosphorus harvesting from fresh human urine: A strategy of precisely recovering high-purity calcium phosphate and insights into the precipitation conversion mechanism

Phosphorus (P) harvesting from source-separated urine to optimize the overall nutrient loop is one of the most appealing benefits and is a global research interest in wastewater management and treatment. However, current P precipitation is mainly oriented to struvite, which is limited by the issues such as relatively low product purity and high cost of Mg source. Distinguished from previous conventional struvite precipitation, the strategy of precisely harvesting P from fresh human urine as high-purity calcium phosphate was first proposed in this study. This enhanced strategy can optimize P harvesting performance and product purity by simply regulating the consumption of calcium-based materials via model simulation and experimental validation. The thermodynamic model was constructed to probe the precipitation conversion mechanism, and visually predict the component and yield for products under various operating conditions. Batch experiments were conducted to investigate P recovery performance as a function of initial Mg²⁺ concentration, initial pH level, as well as degree of urine hydrolysis. Moreover, the alternative dosing scheme with different calcium salts and alkali was presented, diversifying the options for efficient P recovery. The results showed that, from the perspective of acidic storage for fresh urine, P recovery can be boosted along with eliminating urine hydrolysis. In urine with an initial pH=2.0, P can be completely recovered and purity for calcium phosphate can be optimized to 100% within a Ca/P ratio range of 1.67-2.3. Overall, this work is of great significance for precisely and efficiently harvesting P from urine and provides an integrated strategy for P resource recovery from urine.

Recovery of phosphorus from wastewater: A review based on current phosphorous removal technologies

Phosphorus (P) as an essential nutrient for life sustains the productivity of food systems; yet misdirected P often accumulates in wastewater and triggers water eutrophication if not properly treated. Although technologies have been developed to remove P, little attention has been paid to the recovery of P from wastewater. This work provides a comprehensive review of the state-of-the-art P removal technologies in the science of wastewater treatment. Our analyses focus on the mechanisms, removal efficiencies, and recovery potential of four typical water and wastewater treatment processes including precipitation, biological treatment, membrane separation, and adsorption. The design principles, feasibility, operation parameters, and pros & cons of these technologies are analyzed and compared. Perspectives and future research of P removal and recovery are also proposed in the context of paradigm shift to sustainable water treatment technology.

Converting Chrysotile Nanotubes into Magnesium Oxide and Hydroxide Using Lanthanum Oxycarbonate Hybridization and Alkaline Treatment for Efficient Phosphate Adsorption

Magnesium oxide and hydroxide nanomaterials comprise a class of promising advanced functional metal nanomaterials whose use in environmental and material applications is increasing. Several strategies to synthesize these nanomaterials have been described but are unsustainable and uneconomic. This work reports on a processing strategy that turns natural magnesium-rich chrysotile into magnesium oxide and hydroxide nanoparticles via nanoparticle hybridization and an alkaline process while enabling La-based nanoparticles to coat the chrysotile nanotube surfaces. The adsorbent's resulting hybrid nanostructure had an outstanding capacity for phosphate uptake (135.2 mg P g^-1) and enhanced regeneration performance. Furthermore, the adsorbent featured wide applicability with respect to the coexistence of competitive anions and a broad range of pH conditions, and its high-performance phosphate removal from sewage effluent was also demonstrated. Spectroscopic and microscopic analyses revealed the scavenging ability of phosphate by the La-based and Mg-based nanoparticles and the multiple capture mechanisms involved, including surface complexation and ion exchange. This proposed approach expands chrysotile's potential use as a magnesium-rich nanomaterial and harbors great promise for the removal of pollutants in a variety of real-world settings.

Arsenic Oxidation and Removal from Water via Core-Shell MnO2@La(OH)3 Nanocomposite Adsorption

Arsenic (As(III)), more toxic and with less affinity than arsenate (As(V)), is hard to remove from the aqueous phase due to the lack of efficient adsorbents. In this study, a core-shell structured MnO₂@La(OH)₃ nanocomposite was synthesized via a facile two-step precipitation method. Its removal performance and mechanisms for As(V) and As(III) were investigated through batch adsorption experiments and a series of analysis methods including the transformation kinetics of arsenic species in As(III) removal, FTIR, XRD and XPS. Solution pH could significantly influence the removal efficiencies of arsenic. The adsorption process of As(V) occurred rapidly in the first 5 h and then gradually decreased, whereas the As(III) removal rate was relatively slower. The maximum adsorption capacities of As(V) and As(III) were up to 138.9 and 139.9 mg/g at pH 4.0, respectively. For As(V) removal, the inner-sphere complexes of lanthanum arsenate were formed through the ligand exchange reactions and coprecipitation. The oxidation of As(III) to the less toxic As(V) by δ-MnO₂ and subsequently the synergistic adsorption process by the lanthanum hydroxide on the MnO₂@La(OH)₃ nanocomposite to form lanthanum arsenate were the dominant mechanisms of As(III) removal. XPS analysis indicated that approximately 20.6% of Mn in the nanocomposite after As(III) removal were Mn(II). Furthermore, a small amount of Mn(II) and La(III) were released into solution during the process of As(III) removal. These results confirm its efficient performance in the arsenic-containing water treatment, such as As(III)-contaminated groundwater used for irrigation and As(V)-contaminated industrial wastewater.

Retention of thallium(I) on goethite, hematite, and manganite: Quantitative insights and mechanistic study

The reversibility of monovalent thallium (Tl) absorption on widely distributed iron/manganese secondary minerals may affect environmental Tl migration and global cycling. Nevertheless, quantitative and mechanistic studies on the interfacial retention and release reactions involving Tl(I) are limited. In this study, batch and stirred-flow experiments, unified kinetics modeling, spectral detection, and theoretical calculations were used to elucidate the retention behaviors of Tl(I) on goethite, hematite, and manganite with different solution pH values and Tl loading concentrations. Sustained Tl(I) retention (k_{d, MeOHTl}=0.005∼0.018 min^-1) was induced by hydration of the surface hydroxyl groups. Rapid Tl(I) retention (k_d,MeOTlOH=1.232∼2.917 min^-1) was enhanced by the abundant hydroxide ions and deprotonated hydroxyl groups, which increased the Tl(I) binding ability. Compared to the ambient Tl concentration, pH had a more substantial effect on the formation and distribution of surface Tl(I) binding species. In alkaline environments, the large adsorption energy for Tl(I) binding to surface species (E_ads=-6.14 eV) induced fast Tl(I) binding response on the surfaces of iron/manganese secondary minerals. This study provides new insights into the heterogeneous surface complexation and retention behaviors of Tl(I) and contributes to an in-depth understanding of the environmental fate of Tl and the remediation of Tl contamination.

Phosphate sequestration by lanthanum-layered rare earth hydroxides through multiple mechanisms while avoiding the attenuation effect from sediment particles in lake water

Lanthanum-based adsorbents have been used extensively to capture phosphate from wastewater. However, the attenuation effect that arises from the coexistence of sediment and humic acid is the major drawback in practical applications. The Lanthanum-layered rare earth hydroxides (LRHs)-Cl (La-LRH-Cl) was synthesized and achieved high elemental phosphorus (P) adsorption capacity (138.9 mg-P g^-1) along with a fast adsorption rate (k₂ = 0.0031 g mg^-1·min^-1) over a wide pH range while avoiding the attenuation effect that arises from the coexistence of sediment and humic acid in lake water. The La-LRH-Cl effectively captured phosphate through multiple interactions, such as the ion exchange of Cl^- and phosphate, the memory effect of LRH and the inner-sphere complexation of La-P. Moreover, physical models demonstrated that the adsorption of phosphate onto La-LRH-Cl was a monolayer endothermic process, during which PO₄^3- interacted by multi-docking via parallel orientation at 293 K and multi-ionic interactions through pure non-parallel orientation at 303 K. Hence, 1000 L of 11.08 mg-P L^-1 of the acquired lake water was decontaminated by 30 g of La-LRH-Cl to 0.09 mg-P L^-1 within 7 days. In addition, over ~12,125 BV of an industrial effluent containing 3.26 mg-P L^-1 was treated to below USEPA's discharge limit in fixed-bed tests. It was found that the memory effect of LRH was responsible for the stable performance and reusability. Therefore, more focus should be placed on the collective role of La and LRH layered structure as a means of preventing the attenuation effect in the real water matrix.

Electroprecipitation of Nanometer-Thick Films of Ln(OH)3 [Ln = La, Ce, and Lu] at Pt Microelectrodes and Their Effect on Electron-Transfer Reactions

We report investigations of the deposition of nanometer-thick Ln(OH)₃ films (Ln = La, Ce, and Lu) and their effect on outer-sphere and inner-sphere electron-transfer reactions. Insoluble Ln(OH)₃ films are deposited from aqueous solutions of LaCl₃ onto the surface of 12.5 μm radius Pt microdisk electrodes during water or oxygen reduction. Both reactions produce interfacial OH^-, which complexes with Ln³⁺, resulting in the precipitation of Ln(OH)₃. Surface analyses by scanning electron microscopy (SEM), SEM-energy-dispersive X-ray spectroscopy, and atomic force microscopy indicate the formation of a 1-2 nm thick uniform film. Outer-sphere electron-transfer reactions (Ru(NH₃)₆³⁺ reduction, FcMeOH oxidation, and Fe(CN)₆^4-/3- oxidation/reduction) were investigated at Ln(OH)₃-modified electrodes of different film thicknesses. The results demonstrate that the steady-state transport-limited current for these reactions decreases with an increase in the film thickness. Moreover, the degree of blockage depends upon the redox species, suggesting that the Ln(OH)₃ films are free from pinholes greater than the size of the redox molecules. This suggests that the films are either ionically conducting or that electron tunneling occurs across these thin layers. A similar blocking effect was observed for the inner-sphere reductions of H₂O and O₂. We further demonstrate that the thickness of La(OH)₃ films can be controlled by anodic dissolution. Additionally, we show that La³⁺ lowers the supersaturation of dissolved H₂ required to nucleate a stable nanobubble.

Mechanisms of orthophosphate removal from water by lanthanum carbonate and other lanthanum-containing materials

Removing phosphorus (P) from water and wastewater is essential for preventing eutrophication and protecting environmental quality. Lanthanum [La(III)]-containing materials can effectively and selectively remove orthophosphate (PO₄) from aqueous systems, but there remains a need to better understand the underlying mechanism of PO₄ removal. Our objectives were to 1) identify the mechanism of PO₄ removal by La-containing materials and 2) evaluate the ability of a new material, La₂(CO₃)_3(s), to remove PO₄ from different aqueous matrices, including municipal wastewater. We determined the dominant mechanism of PO₄ removal by comparing geochemical simulations with equilibrium data from batch experiments and analyzing reaction products by X-ray diffraction and scanning transmission electron microscopy with energy dispersive spectroscopy. Geochemical simulations of aqueous systems containing PO₄ and La-containing materials predicted that PO₄ removal occurs via precipitation of poorly soluble LaPO_4(s). Results from batch experiments agreed with those obtained from geochemical simulations, and mineralogical characterization of the reaction products were consistent with PO₄ removal occurring primarily by precipitation of LaPO_4(s). Between pH 1.5 and 12.9, La₂(CO₃)_3(s) selectively removed PO₄ over other anions from different aqueous matrices, including treated wastewater. However, the rate of PO₄ removal decreased with increasing solution pH. In comparison to other solids, such as La(OH)_3(s), La₂(CO₃)_3(s) exhibits a relatively low solubility, particularly under slightly acidic conditions. Consequently, release of La³⁺ into the environment can be minimized when La₂(CO₃)_3(s) is deployed for PO₄ sequestration.

Well-defined bimetal oxides derived from Prussian blue analogues with regulable active sites for phosphate removal

Two well-defined CoFe bimetal oxides are prepared from Prussian blue analogues (PBAs) as precursors with designable structures, which are further explored for phosphate removal. A speed-controlled coordination strategy is used to fabricate two CoFe PBA microcrystals with different morphologies, then two regular CoFe oxides are obtained via an intermediate-temperature calcination. CoFeS, a slow-speed coordination product with truncated microcube structure, contains less coordinated water and Fe³⁺ in its framework, but can create more mesopores and Fe³⁺ in its oxidative product of CoFeST300. CoFeST300 has been demonstrated to have higher adsorption capacity and affinity for phosphate adsorption compared to that of the fast-speed coordination product, due to its more Fe³⁺ as effective adsorption sites via ligand exchange. Besides, the inner-sphere complexation mechanism makes CoFeST300 high selectivity for phosphate removal compared to other co-existing anions. The application performance of CoFeST300 is examined by multiple continuous treatment of actual sewage, and the result of all effluent concentrations below 0.5 mg P/L verifies a promising potential of the fabricated adsorbent for phosphorus removal. Thus, design or regulation of the precursors is an efficiency method to fabricate an ideal metal oxide for phosphate adsorption.

Structural insight into the alginate derived nano-La(OH)3/porous carbon composites for highly selective adsorption of phosphate

In this study, a novel nano-La(OH)₃/porous carbon composites derived from La alginate xerogel with egg-box structure had been successfully synthesized by a gradient heat treatment in nitrogen atmosphere. This facile fabrication strategy can be easily employed to considerably encapsulate La(OH)₃ nanoparticles uniformly into the porous carbon matrix derived from the alginate macromolecule framework. The optimized sample, labeled as LS-550(N), exhibited extremely high phosphate uptake and great selectivity. The adsorption kinetic process dramatically followed pseudo-second-order model. The Langmuir model fitted maximum equilibrium adsorption capacity is 133.58 mg·g^-1. The phosphate adsorption mechanisms could be consist of electrostatic interaction, complexation and ligand exchange interaction on the surface of LS-550(N). The prominent practical applicability of LS-550(N) in the regeneration test suggests that the LS-550(N) could be a potential adsorption candidate for the decontamination of phosphate-containing natural water bodies.

Three-dimensional graphene/La(OH)3-nanorod aerogel adsorbent by self-assembly process for enhanced removal and recovery of phosphate in wastewater

Removal and recovery of phosphorus (P) from wastewater is beneficial to both environmental protection and resource sustainability. Enriching the low concentration of P in wastewater will greatly facilitate the effective recovery of P. To enhance the adsorption performance and recyclability of adsorbents for low concentration P-containing wastewater, a novel three-dimensional (3D) graphene/La(OH)₃-nanorod aerogel (GLA) was prepared by a unique self-assembly process in this study. Benefiting from the large specific surface area of graphene aerogel, which provides sufficient loading sites for the favorable dispersion of La(OH)₃ nanorods, the GLA achieves an excellent P adsorption capacity of 76.85 mg/g. It is also highly selective for P, with adsorption capacity reduced by only 14% and 11% under the interference of high concentration of dissolved organic matter or multiple competing anions respectively. Further mechanistic investigation revealed that the whole adsorption process consists of three stages: (1) ion-exchange process; (2) LaP inter-sphere coordination process; and (3) crystal evolution process. In the continuous flow adsorption-desorption cycles, the P concentration was concentrated ~25 times that of the feeding water (2 mg P/L). To our knowledge, this is the first time that La-modified graphene aerogel has been studied for P recovery. This provides a new method for the P removal and recovery of low concentration P-containing wastewater.

Novel benzylphosphate-based covalent porous organic polymers for the effective capture of rare earth elements from aqueous solutions

It has been a major challenge to develop stable and cost-effective porous materials that efficiently recover heavy rare earth elements (HREEs) due to ever-increasing demand, low availability and high cost of HREEs. This study presents two novel benzylphosphate-based covalent porous organic polymers (BPOP-1 and BPOP-2) that were prepared by facile one-pot Friedel-Crafts reactions. Various analytical techniques are used to investigate the successful syntheses of BPOP materials and establish their material properties, which include an unusual crystalline nature, large surface area, hierarchical pore structure, and superior chemical stabilities. The BPOPs effectively adsorb, and thus remove HREEs from aqueous media. In particular, BPOP-1 had higher phosphate content and exhibits superior adsorption capacities (Eu³⁺: 289.5; Gd³⁺: 292.7; Tb³⁺: 294.4; Dy³⁺: 301.9 mg/g) than BPOP-2, while BPOP-2 had higher mesoporosity and correspondingly supports faster adsorption kinetics. Remarkably, both BPOP materials exhibit some of the highest HREE adsorption capacities reported to date, the selective capture of Dy³⁺ ions, and excellent cyclic adsorption/desorption properties. We provide a potential adsorption mechanism for Dy³⁺ capture by the BPOP adsorbent. These demonstrate that introducing phosphate functionality into a robust porous polymer backbone with high surface area is a promising strategy for selective HREEs capture from wastewater.

Lanthanum hydroxide engineered sewage sludge biochar for efficient phosphate elimination: Mechanism interpretation using physical modelling

In the present study, lanthanum hydroxide (La OH)-engineered sewage sludge biochar (La-SSBC) was utilized for efficient phosphate elimination from an aqueous medium. A high adsorption capacity of 312.55 mg P/g was achieved using La-SSBC at 20 °C, which was an excellent adsorbent performance in comparison to other biochar-based adsorbents. Additionally, the performance of La-SSBC was stable even at wider range of pH level, the existence of abundant active anions, and recycling experiments. Statistical physics modeling with the fitting method based on the Levenberg-Marquardt iterating algorithm, as well as various chemical characterizations, suggested the unique double-layered mechanism of phosphate capturing: one functional group of La-SSBC adsorbent describing a prone direction of the PO₄ ions on the stabilize surface in a multi-ionic process, forming the first layer adsorption. Additionally, SSBC played an important role by releasing positively charged cations in solution, overcoming the electronic repulsion to form a second layer, and achieving excellent adsorption capacity. The calculation of multiple physicochemical parameters including adsorption energy further evidenced the process. This two-layered mechanism sheds light on the complex interaction between phosphate and biochar. Moreover, the management of sewage sludge associated with the requirement of cost-effectively and environmentally acceptable mode. Therefore, the present investigation demonstrated an efficient approach of the simultaneous sewage sludge utilization and phosphate removal.

Rapid and selective harvest of low-concentration phosphate by La(OH)3 loaded magnetic cationic hydrogel from aqueous solution: Surface migration of phosphate from -N+(CH3)3 to La(OH)3

Phosphate is an important factor for the occurrence of surface water eutrophication, and is also a non-renewable resource which faces a potential depletion crisis. In this study, La(OH)₃ loaded magnetic cationic hydrogel composite MCH-La(OH)₃-EW was used to absorb low strength phosphate in simulated water and real water. The adsorption amount of MCH-La(OH)₃-EW was 39.14 ± 0.31 mg P/g and the equilibrium time was 120 min at the initial phosphate concentration of 2.0 mg P/L. The adsorption process was a spontaneous endothermic reaction. MCH-La(OH)₃-EW exhibited a high selectivity towards phosphate within pH of 4.0-10.0 or in the presence of co-existing ions (including Cl^-, SO₄^2-, NO₃^-, HCO₃^-, SiO₃^2-) and humic acid. After 10 cycles of adsorption-desorption, the adsorption amount of regenerated MCH-La(OH)₃-EW still remained at 63.4% of its maximum value. For the real water sample with phosphate concentration of 2.0 mg P/L, the phosphate removal efficiency could achieve 97.65-98.90% and the effluent turbidity was 2.10-4.27 NTU at the MCH-La(OH)₃-EW dosage of 0.04 g/L. The adsorption mechanism analysis showed that both quaternary amine groups (-N⁺(CH₃)₃) and La(OH)₃ of MCH-La(OH)₃-EW were involved in the process of phosphate adsorption. The electrostatic interaction between phosphate and -N⁺(CH₃)₃ rapidly occurred at the initial stage of adsorption process, then the electrostatic absorbed phosphate migrated to La(OH)₃ on the surface of MCH-La(OH)₃-EW via ligand exchange to form inner-sphere complex. This phenomenon was conducive to phosphate adsorption kinetics by MCH-La(OH)₃-EW.

Phosphate removal from aqueous solution by Fe-La binary (hydr)oxides: characterizations and mechanisms

In this study, Fe-La binary (hydr)oxides were prepared by a co-precipitation method for phosphate removal. Various techniques, including secondary electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), powder X-ray diffraction (p-XRD), and Brunauer-Emmett-Teller (BET) surface area analysis, were employed to characterize the synthesized Fe-La binary (hydr)oxides. Batch experiments indicated that the performance of phosphate removal by Fe-La binary (hydr)oxides was excellent and increased with increasing the concentrations of La. The kinetics study showed that the adsorption was rapid and described better by the pseudo-second-order equation. The maximum adsorption capacities of Fe/La 3:1, Fe/La 1:1, and Fe/La 1:3 binary (hydr)oxides at pH 4.0 calculated by Langmuir model were 49.02, 69.44, and 136.99 mg/g, respectively. The uptake of phosphate was highly affected by solution pH and significantly reduced with the increase of pH value. The analyses of p-XRD, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) suggested that the predominant mechanisms of phosphate removal involved surface hydroxyl exchange reactions and co-precipitation of released La³⁺ and phosphate ions, which resulted into the formation of amorphous phase of rhabdophane (LaPO₄·0.5H₂O). The results show great potential for the application on the treatment of phosphate decontamination for their high efficiency of phosphate removal.

High phosphate removal using La(OH)3 loaded chitosan based composites and mechanistic study

Our present study was to prepare a biomass-supported adsorbents with high adsorptive capacity and high selectivity to prevent the accelerated eutrophication in water body. To this end, different metal hydroxide (La, Zr and Fe) first was successfully loaded on chitosan microspheres. Then the quaternary ammonium group with different content was introduced into the adsorbent by polymerization. By comparison of adsorption properties, chitosan-La(OH)₃-quaternary ammonium-20% (CS-La-N-20%) has strong adsorption to phosphate (160 mg/g) by immobilizing nano-sized La(OH)₃ within a quaternary-aminated chitosan and it maintain high adsorption in the presence of salt ions. The pH results indicated that the CS-La-N-20% would effectively sequestrate phosphate over a wide pH range between 3 and 7 without significant La³⁺ leaching. What's more, adsorption capacity on the introduce of positively charged quanternary-aminated groups was significantly higher than that of the unmodified adsorbents at alkaline conditions. The column adsorption capacity reached 1300 bed volumes (BV) when phosphate concentration decreased until 0.5 mg/L at 6 BV/hr. The column adsorption/desorption reveals that no significant capacity loss is observed, indicating excellent stability and repeated use property. Characterizations revealed that phosphate adsorption on CS-La-N-20% through ligand exchange (impregnated nano-La(OH)₃) and electrostatic attraction (positively charged quanternary-aminated groups). All the results suggested that CS-La-N-20% can serve as a promising adsorbent for preferable phosphate removal in realistic application.

Competitive arsenate and phosphate adsorption on α-FeOOH, LaOOH, and nano-TiO2: Two-dimensional correlation spectroscopy study

Competitive adsorption of arsenate (AsO₄^3-) and phosphate (PO₄^3-) on α-FeOOH, LaOOH, and nano-TiO₂ was studied using batch adsorption experiments and in-situ flow cell ATR-FTIR coupled with two-dimensional correlation spectroscopy (2D-COS) for the first time. With a higher temporal resolution, our results found a highly dynamic adsorption sequence for AsO₄^3- and PO₄^3-. When AsO₄^3- and PO₄^3- were simultaneously exposed to the adsorbents at the same concentrations, AsO₄^3- was preferentially adsorbed by α-FeOOH and TiO₂, but PO₄^3- adsorption was dominant on LaOOH. The results implied that the PO₄^3- adsorbed on LaOOH had to be remobilized to allow for AsO₄^3- adsorption, but that PO₄^3- adsorption on α-FeOOH and TiO₂ was hindered by faster AsO₄^3- adsorption. Crystal orbital Hamilton population (COHP) analysis revealed that AsO₄^3- complexes bonded more strongly on α-FeOOH and TiO₂, whereas PO₄^3- complexes were more stable on LaOOH. Different adsorption sequences and the stability of the complexes were attributed to the diverse geometric configurations of AsO₄^3- and PO₄^3- on metal oxides surfaces with specific bonding chemistry. The presence of Ca²⁺ did not affect AsO₄^3- and PO₄^3- adsorption sequence on α-FeOOH or LaOOH, but it reversed the adsorption sequence on TiO₂ due to the formation of ternary surface complexes on TiO₂ surfaces.

Coupled influence of pH and dissolved organic carbon on the immobilization of phosphorus by lanthanum-modified zeolite

Wind-driven waves and currents in shallow lakes frequently trigger the resuspension of sediments in the photic layer, which is characterized with a high pH and high dissolved organic carbon (DOC) concentration. The mechanism of phosphorus-inactivating agents (PIAs) immobilizing phosphorus under the coupled influence of pH and DOC is not clarified, and the applicability of PIAs in eutrophic shallow lakes is thus still doubtful. We found that, under the coupled influence of pH and DOC, the uptake of phosphate by LMZ was affected mainly by pH at low DOC concentrations and by DOC at high DOC concentrations. A high pH (9.3) and high DOC concentration (24.7 mg/L) greatly increased the release of phosphorus from sediment to water. However, the addition of LMZ substantially reduced the P concentrations in water, mainly via capture of dissolved inorganic phosphorus. The results of the reversibility of the adsorption of phosphates and DOC showed that phosphate had much higher affinity than DOC towards LMZ. The phosphate once adsorbed on LMZ was resistant to release when exposed to conditions of either a high pH (9.5), high DOC concentration (250 mg/L) or both; i.e., only <5% of the adsorbed phosphate is releasable. Therefore, we proposed that, to avoid the coupled influence of pH and DOC in the photic layer of eutrophic shallow lakes, LMZ could be applied in multiple low doses in the season when the growth of algae is minimal (a low pH and low DOC concentration).