Versatile Surface Modification of TFC Membrane by Layer-by-Layer Assembly of Phytic Acid-Metal Complexes for Comprehensively Enhanced FO Performance

An Innovative Surface Modification Technique for Antifouling Polyamide Nanofiltration Membranes

In this study, we developed a novel surface coating technique to modify the surface chemistry of thin film composite (TFC) nanofiltration (NF) membranes, aiming to mitigate organic fouling while maintaining the membrane's permselectivity. We formed a spot-like polyester (PE) coating on top of a polyamide (PA) TFC membrane using mist-based interfacial polymerization. This process involved exposing the membrane surface to tiny droplets carrying different concentrations of sulfonated kraft lignin (SKL, 3, 5, and 7 wt %) and trimesoyl chloride (TMC, 0.2 wt %). The main advantages of this surface coating technique are minimal solvent consumption (less than 0.05 mL/cm2) and precise control over interfacial polymerization. Zeta potential measurements of the coated membranes exhibited enhancements in negative charge compared to the control membrane. This enhancement is attributed to the unreacted carboxyl functional groups of the SKL and TMC monomers, as well as the presence of sulfonate groups (SO3) in the structure of SKL. AFM results showed a notable decrease in membrane surface roughness after polyester coating due to the slower diffusion of SKL to the interface and a milder reaction with TMC. In terms of fouling resistance, the membrane coated with a polyester composed of 7 wt % SKL showed a 90% flux recovery ratio (FRR) during Bovine Serum Albumin (BSA) filtration, showing a 15% improvement compared to the control membrane (PA). PE-coated membranes provided stable separation performance over 40 h of filtration. The sodium chloride rejection and water flux displayed minimal variations, indicating the robustness of the coating layer. The final section of the presented study focuses on assessing the feasibility of scaling up and the cost-effectiveness of the proposed technique. The demonstrated ease of scalability and a notable reduction in chemical consumption establish this method as a viable, environmentally friendly, and sustainable solution for surface modification.

Durable and Robust Antibacterial Polypropylene Hernia Mesh for Abdominal Wall Defect Repair

Polypropylene (PP) mesh is commonly used in repairing abdominal wall hernia (AWH). However, the use of synthetic prosthesis comes with the risk of developing a prosthetic infection, resulting in delayed healing, secondary surgery, and potentially increased mortality. To address these issues, a facile surface functionalization strategy for PP mesh based on phytic acid (PA) and polyhexamethylene guanidine (PHMG) was constructed through a one-step co-deposition process, referred to as the PA/PHMG coating. The development of PA/PHMG coating is mainly attributed to the surface affinity of PA and the electrostatic interactions between PA and PHMG. The PA/PHMG coating could be completed within 4 h under mild conditions. The prepared PA/PHMG coatings on PP mesh surfaces exhibited desirable biocompatibility toward mammalian cells and excellent antibacterial properties against the notorious "superbug" methicillin-resistant Staphylococcus aureus (MRSA) and tetracycline-resistant Escherichia coli (TRE). The PA/PHMG-coated PP meshes showed killing ratios of over 99% against MRSA in an infected abdominal wall hernia repair model. Furthermore, histological and immunohistochemical analysis revealed a significantly attenuated degree of neutrophil infiltration in the PA/PHMG coating group, attributed to the decreased bacterial numbers alleviating the inflammatory response at the implant sites. Meanwhile, the pristine PP and PA/PHMG-coated meshes showed effective tissue repair, with the PA/PHMG coating group exhibiting enhanced angiogenesis compared with pristine PP meshes, suggesting superior tissue restoration. Additionally, PP meshes with the highest PHMG weight ratio (PA/PHMG(3)) exhibited excellent long-term robustness under phosphate-buffered saline (PBS) immersion with a killing ratio against MRSA still exceeding 95% after 60 days of PBS immersion. The present work provides a facile and promising approach for developing antibacterial implants.

Substantial Confinement of Crystal Growth of Organic Crystalline Materials in Metal-Organic Membrane Microshells

This study proposes a robust microshell encapsulation system in which a metal-organic membrane (MOM), consisting of phytic acids (PAs) and metal ions, intrinsically prevents the molecular crystal growth of organic crystalline materials (OCMs). To develop this system, OCM-containing oil-in-water (O/W) Pickering emulsions were enveloped with the MOM, in which anionic pulp cellulose nanofiber (PCNF) primers electrostatically captured zinc ions at the O/W interface and chelated with PA, thus producing the MOM with a controlled shell thickness at the micron scale. We ascertained that the MOM formation fills and covers ∼75% of the surface pore size of PCNF films, which enhances the interfacial modulus by 2 orders of magnitude compared to that when treated with bare PCNFs. Through a feasibility test using a series of common OCMs, including ethylhexyl triazone, avobenzone, and ceramide, we demonstrated the excellent ability of our MOM microshell system to stably encapsulate OCMs while retaining their original molecular structures over time. These findings indicate that our MOM-reinforced microshell technology can be applied as a platform to substantially confine the crystal growth of various types of OCMs.

Enhanced Mono/Divalent Ion Separation via Charged Interlayer Channels in Montmorillonite-Based Membranes

Efficient mono- and divalent ion separation is pivotal for environmental conservation and energy utilization. Two-dimensional (2D) materials featuring interlayer nanochannels exhibit unique water and ion transport properties, rendering them highly suitable for water treatment membranes. In this work, we incorporated polydopamine/polyethylenimine (PDA/PEI) copolymers into 2D montmorillonite (MMT) nanosheet interlayer channels through electrostatic interactions and bioinspired bonding. A modified laminar structure was formed on the substrate surface via a straightforward vacuum filtration. The electrodialysis experiments reveal that these membranes could achieve monovalent permselectivity of 11.06 and Na+ flux of 2.09 × 10-8 mol cm-2 s-1. The enhanced permselectivity results from the synergistic effect of electrostatic and steric hindrance effect. In addition, the interaction between the PDA/PEI copolymer and the MMT nanosheet ensures the long-term operational stability of the membranes. Theoretical simulations reveal that Na+ has a lower migration energy barrier and higher migration rate for the modified MMT-based membrane compared to Mg2+. This work presents a novel approach for the development of monovalent permselective membranes.

In situ reduction of Ag nanoparticles using okra polysaccharides for the preparation of flexible multifunctional sensors

This paper reports the fabrication of flexible films loaded with Ag nanoparticles (Ag NPs) and annotated as POPA films from polyvinyl alcohol, okra polysaccharides, phytic acid, and AgNO3 via an in situ reduction and solution-casting method. The prepared films exhibit strain, temperature, and humidity sensing. As a flexible strain sensor, the POPA sensor has a wide strain sensing range (1-250 %), and fast response/recovery (0.22/0.28 s), while as a temperature sensor, it senses the human body temperature and exhibits excellent temperature sensitivity (TCR = -1.401 % °C-1) and good linearity (R2 = 0.994) in the temperature range of 30-55 °C. Additionally, in the relative humidity (RH) of range 35-95 %, the POPA humidity sensor outputs stable electrical signals during adsorption and desorption. Moreover, it exhibits low hysteresis values (3.19 % RH) and good linearity (R2 = 0.989) for the detection of breathing rates during different human body states. Consequently, the POPA sensor exhibits good stability, repeatability, and reversibility for strain, temperature, and humidity sensing. The designed multifunctional POPA sensor thus holds great potential for its application in flexible wearable devices and electronics.

Plant-based Biomass/Polyvinyl Alcohol Gels for Flexible Sensors

Flexible sensors show great application potential in wearable electronics, human-computer interaction, medical health, bionic electronic skin and other fields. Compared with rigid sensors, hydrogel-based devices are more flexible and biocompatible and can easily fit the skin or be implanted into the body, making them more advantageous in the field of flexible electronics. In all designs, polyvinyl alcohol (PVA) series hydrogels exhibit high mechanical strength, excellent sensitivity and fatigue resistance, which make them promising candidates for flexible electronic sensing devices. This paper has reviewed the latest progress of PVA/plant-based biomass hydrogels in the construction of flexible sensor applications. We first briefly introduced representative plant biomass materials, including sodium alginate, phytic acid, starch, cellulose and lignin, and summarized their unique physical and chemical properties. After that, the design principles and performance indicators of hydrogel sensors are highlighted, and representative examples of PVA/plant-based biomass hydrogel applications in wearable electronics are illustrated. Finally, the future research is briefly prospected. We hope it can promote the research of novel green flexible sensors based on PVA/biomass hydrogel.

In Situ Formation of Silver Nanoparticles Induced by Cl-Doped Carbon Quantum Dots for Enhanced Separation and Antibacterial Performance of Nanofiltration Membrane

Polyamide (PA) nanofiltration (NF) membranes suffer from biofouling, which will deteriorate their separation performance. In this study, we proposed a strategy to incorporate silver nanoparticles (Ag NPs) into PA NF membranes in situ, in order to simultaneously enhance water permeability and antibacterial performance. The chloride-doped carbon quantum dots (Cl-CQDs) with photocatalytic performance were pre-embedded in the PA selective layer. Under visible light irradiation, the photogenerated charge carriers generated by Cl-CQDs rapidly transported to silver ions (Ag+ ions), resulting in the in situ formation of Ag NPs. The proposed strategy avoided the problem of aggregating Ag NPs, and the amount of Ag NPs on the membrane surfaces could be easily tuned by changing silver nitrate (AgNO3) concentrations and immersion times. These uniformly dispersed Ag NPs increased membrane hydrophilicity. Thus, the obtained thin film nanocomposite Ag NPs (TFN-Ag) membrane exhibited an improved water flux (31.74 L m-2 h-1), which was ~2.98 times that of the pristine PA membrane; meanwhile, the sodium sulfate (Na2SO4) rejection rate was 96.11%. The sterilization rates of the TFN-Ag membrane against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were 99.55% and 99.52%, respectively. Thus, this facile strategy simultaneously improved the permeability and antibacterial property of PA NF membranes.

Multi-functional bio-film based on sisal cellulose nanofibres and carboxymethyl chitosan with flame retardancy, water resistance, and self-cleaning for fire alarm sensors

Flexible and environmentally friendly bio-based films have attracted significant attention as next-generation fire-responsive sensors. However, the low structural stability, durability, and flame retardancy of pure bio-based films limit their application in outdoor and extreme environments. Here, we report the design of a sustainable bio-based composite film assembled from carboxymethyl-modified sisal fibre microcrystals (C-MSF), carboxymethyl chitosan (CMC), graphene nanosheets (GNs), phytic acid (PA), and trivalent iron ions (Fe³⁺). Cross-linking between Fe³⁺ and the C-MSF/CMC matrix and the formation of PA-Fe³⁺ complexes on the surface of the film imparted excellent mechanical properties, chemical stability, self-cleaning ability, and flame retardancy to the bio-film. Furthermore, the bio-film produced a reversible and sensitive response to temperature at 55.3-214.1 °C, and a fire alarm system made from the bio-film had a fire-response time of 4.6 s. In addition, the char layer of the bio-film retained a stable cyclic response to temperature, enabling it to serve as a fire resurgence sensor with a response time of 2.3 s and recovery time of 11.2 s. This work provides a simple pathway for the fabrication of self-cleaning, flame retardant, and water-resistant bio-films that can be assembled into fire alarm systems for the real-time monitoring of fire accidents and resurgence.

Roles and gains of coordination chemistry in nanofiltration membrane: A review

The nanofiltration (NF) membranes with the specific separation accuracy for molecules with the size of 0.5-2 nm have been applied in various industries. However, the traditional polymeric NF membranes still face problems like the trade-off effect, organic solvent consumption, and weak durability in harsh conditions. The participation of coordination action or metal-organic coordination compounds (MOCs) brings the membrane with uniform pores, better antifouling properties, and high hydrophilicity. Some of the aqueous-phase reactions also help to introduce a green fabrication process to NF membranes. This review critically summarizes the recent research progress in coordination chemistry relevant NF membranes. The participation of coordination chemistry was classified by the various functions in NF membranes like additives, interlayers, selective layers, coating layers, and cross-linkers. Then, the effect and mechanism of the coordination chemistry on the performance of NF membranes are discussed in depth. Perspectives are given for the further promotion that coordination chemistry can make in NF processes. This review also provides comprehensive insight and constructive guidance on high-performance NF membranes with coordination chemistry.

Anti-Oil-Adhesion Property of Superhydrophilic/Underwater Superoleophobic Phytic Acid-FeIII Complex Coatings

Crude oil adhesion issues are widespread in the petroleum industry, leading to inefficient production and high maintenance costs. Developing efficient antifouling materials and investigating the microscopic adhesion mechanism are of substantial significance. In the present work, a superhydrophilic/underwater superoleophobic PAFC coating with excellent antifouling properties was constructed by the coordination-driven self-assembly of phytic acid (PA) and FeCl₃ (FC). The atomic force microscope (AFM) droplet probe technique was employed to elucidate the underlying mechanism of the anti-oil-adhesion property of the PAFC coating. Results showed that the PAFC modification achieved the optimum effect at a molar ratio of 1:3 between PA and Fe^III. Applying a (3-aminopropyl)triethoxysilane (APTES) interlayer can effectively improve the performance of the PAFC coating on silica substrates. AFM droplet probe experiments indicated that the adhesion force between submerged micrometer-sized oil droplets and PAFC-modified substrates was significantly weaker than that with the untreated substrate. Meanwhile, the adhesion forces between oil droplets and surfaces were inversely proportional to the contact angle of the oil in water and were enhanced by higher salinity, lower collision velocity, and stronger loading force. The oil injection and wall sticking tests also confirmed the effectiveness of the PAFC modification in resisting the adhesion of crude oil.

Utilizing the cross-linked effect and reconstruction strategy of phytic acid to build Fe-Co-Ni trimetallic amorphous carbon-matrix compounds as efficient oxygen evolution catalyst

Developing low-cost electrocatalysts with excellent activity is significant for accelerating the slow oxygen evolution reaction (OER). In this work, an effective electrocatalyst is prepared via the cross-linked effect and reconstruction strategy based on inexpensive transition metals (Fe, Co, and Ni) and phytic acid (PA). The feasibility of utilizing the cross-linked effect and reconstruction strategy is due to that PA molecules with strongly electronegative phosphoric acid groups possess a great deal of complexing sites, which can facilitate the formation of large cross-linked network by randomly complexing Fe, Co and Ni ions. And the carboatomic rings in PA molecules will reconstructed as carbon-matrix when PA molecules decompose. The above structural evolution of large cross-linked network and reconstructing process is rigorously analyzed through the characterization methods such as XPS. These analysis results indicate that FeCoNi-PA-300 possesses a high degree of amorphization, an abundant nanoporous structure, and a small nanoparticle size, resulting in a large electrochemically active area. Consequently, FeCoNi-PA-300 just needs low overpotentials of about 271 mV and 286 mV to obtain the current densities of 50 and 100 mA cm-2, respectively. Meaningfully, this synthetic method is a general strategy to meliorate the OER activity and electrical conductivity of other catalysts.

Phytic acid and graphene oxide functionalized sponge with special-wettability and electronegativity for oil-in-water emulsion separation in single-step

Developing an emulsion separation material with one-step in-situ purifying capability and improved security in applications, especially for subsequent scale-up, is valuable but remains a challenge. Herein, the amphiphilic sponge (PA@RGO@MS) was prepared via impregnation and in-situ growth of the negatively charged hydrophilic phytic acid (PA) and the hydrophobic reduced graphene oxide (RGO) on the surface of the melamine sponge (MS) and applied in emulsion purification. The mechanics, wettability, absorption performance of the PA@RGO@MS were analyzed to identify its potential for stable demulsification. Results show that the PA@RGO@MS could purify emulsions (turbidity removal rate = 99.7%; TOC removal rate = 94.14%) in-situ in one step by simple shock absorption, profited from the hydrophilic and demulsification capability of PA, oil absorption of RGO, and wide reaction and storage space of MS. Targeting the emulsion with distinct properties (density, viscosity, and concentration) of the oil phase, the PA@RGO@MS could efficiently enable the purification. Meanwhile, the powerful flame-retardant granted from PA ensures the safe shipment and storage of sponges. The favorable cyclability (turbidity removal rate > 98.5% and TOC removal rate > 89.5% after 10 cycles) and diversified operating modes enhance the practical value of the PA@RGO@MS.

Robust In Situ Fouling Control toward Thin-Film Composite Reverse Osmosis Membrane via One-Step Deposition of a Ternary Homogeneous Metal-Organic Hybrid Layer

Membrane fouling is one of the persistent headaches for water desalination because of the significant detriment to membrane performance and operating cost control. It is a great challenge to overcome such crisis in a facile and robust manner. This work was dedicated to customizing an antifouling thin-film composite (TFC) reverse osmosis (RO) membrane with a polydopamine (PDA)/β-alanine (βAla)/Cu²⁺ ternary homogeneous metal-organic hybrid coating. The metal ions were evenly distributed in a continuous organic network via polydentate coordination. The incorporation of βAla enabled a substantial promotion of the Cu²⁺ loading capacity on the membrane surface. The involved one-step codeposition protocol made the surface engineering practically accessible. The deposition time was optimized to afford an uncompromising permselectivity of the membrane. This novel trinity was a smart blend of anti-adhesive and bactericidal factors, and each component in the all-in-one layer performed its own function. The hydrophilic PDA/βAla phase induced weak deposition propensity of organic foulant and bacteria onto the modified membrane, as elucidated by water flux variation, foulants adhesion profile, and interfacial interaction energy. Meanwhile, the Cu²⁺-loaded surface strongly inactivated the attached bacteria to further alleviate biofouling. Excellent sustainability and stability implied the reliable performance of such trinity-coated membrane in practical service. Given the simplicity and robustness, this work opened a promising avenue for in situ fouling control of TFC RO membranes during water desalination.

Phytic acid assisted ultra-fast in-situ constructing Ni foam-supported amorphous Ni-Fe phytates to enhance catalytic performance for oxygen evolution reaction

It is important for the efficient and low-cost utilization of the clean energies to prepare robust catalytic electrodes for oxygen evolution reaction (OER, the key half-reaction in new energy conversion...

Corn Stalk-Derived Carbon Quantum Dots with Abundant Amino Groups as a Selective-Layer Modifier for Enhancing Chlorine Resistance of Membranes

Low permeability and chlorine resistance of normal thin-film composite (TFC) membranes restrict their practical applications in many fields. This study reports the preparation of a high chlorine-resistant TFC membrane for forward osmosis (FO) by incorporating corn stalk-derived N-doped carbon quantum dots (N-CQDs) into the selective polyamide (PA) layer to construct a polydopamine (PDA) sub-layer (PTFC_CQD). Membrane modification is characterized by surface morphology, hydrophilicity, Zeta potential, and roughness. Results show that TFC_CQD (without PDA pretreatment) and PTFC_CQD membranes possess greater negative surface charges and thinner layer-thickness (less than 68 nm). With N-CQDs and PDA pretreatment, the surface roughness of the PTFC_CQD membrane decreases significantly with the co-existence of microsized balls and flocs with a dense porous structure. With the variation of concentration and type of draw solution, the PTFC_CQD membrane exhibits an excellent permeability with low J_{(reverse salt flux)}/J_{(water flux)} values (0.1-0.25) due to the enhancement of surface hydrophilicity and the shortening of permeable paths. With 16,000 ppm·h chlorination, reverse salt flux of the PTFC_CQD membrane (8.4 g m^-2 h^-1) is far lower than those of TFC_CQD (136.2 g m^-2 h^-1), PTFC (127.6 g m^-2 h^-1), and TFC (132 g m^-2 h^-1) membranes in FO processes. The decline of salt rejection of the PTFC_CQD membrane is only 8.2%, and the normalized salt rejection maintains 0.918 in the RO system (16,000 ppm·h chlorination). Super salt rejection is ascribed to the existence of abundant N-H bonds (N-CQDs), which are preferentially chlorinated by free chlorine to reduce the corrosion of the PA layer. The structure of the PA layer is stable during chlorination also due to the existence of various active groups grafted on the surface. This study may pave a new direction for the preparation of durable biomass-derivative (N-CQD)-modified membranes to satisfy much more possible applications.

A Dopamine/Tannic-Acid-Based Co-Deposition Combined with Phytic Acid Modification to Enhance the Anti-Fouling Property of RO Membrane

Reverse osmosis (RO) membranes are widely used in the field of water treatment. However, there are inevitably various fouling problems during long-term use. Surface engineering of RO membranes, such as hydrophilic modification, has attracted broad attention for improving the anti-fouling performance. In this work, we constructed a green biomimetic composite modification layer on the surface of polyamide membranes using a dopamine (DA)/tannic acid (TA) co-deposited layer to bridge the polyamide surface and hydrophilic phytic acids (PhA). The DA/TA interlayer could firmly adhere to the RO membranes, reducing the aggregation of DA and providing abundant phenolic hydroxyl sites to graft PhA. Meanwhile, the anchored PhA molecule bearing six phosphate groups could effectively improve the superficial hydrophilicity. The membranes were characterized by the SEM, AFM, XPS, water contact angle test, and zeta potential test. After surface modification, the hydrophilicity, smoothness, and surface electronegativity were enhanced obviously. The flux and rejection of the virgin membrane were 76.05 L·m⁻²·h⁻¹ and 97.32%, respectively. While the modified D2/T4-PhA membrane showed decent permeability with a water flux of 57.37 L·m⁻²·h⁻¹ and a salt rejection of 98.29%. In the dynamic fouling test, the modified RO membranes demonstrated enhanced anti-fouling performance toward serum albumins (BSA), sodium alginates (SA), and dodecyl trimethyl ammonium bromides (DTAB). In addition, the modified membrane showed excellent stability in the 40 h long-term test.

Robust immobilization of anionic silver nanoparticles on cellulose filter paper toward a low-cost point-of-use water disinfection system with improved anti-biofouling properties

Silver nanoparticle (AgNP)-decorated cellulose filter paper (FP), a low-cost point-of-use (POU) water disinfection system, can supply affordable and safe drinking water for people in desperate need, especially in rural areas in developing countries. However, owing to the unstable immobilization of AgNPs, silver can leach into the treated drinking water from the FP and exceed the World Health Organization (WHO) drinking water limit (<100 μg L-1), which is a potential threat to both human health and the environment. In this work, in order to robustly immobilize anionic silver nanoparticles (GA@AgNPs), we facilely prepared lipoic acid-modified cellulose filter paper (LA-FP), in which GA@AgNPs were robustly immobilized onto filter paper (GA@AgNPs-LA-FP) by strong chelation via the disulfide bond of LA with the surface of the silver nanoparticles. GA@AgNPs-LA-FP exhibited both excellent bacterial anti-adhesion activity and strong bactericidal activity, which can synergistically mitigate biofouling by inhibiting biofilm formation on the paper surface. Moreover, employed as a gravity-driven bactericidal filter, the GA@AgNPs-LA-FP membrane treated 100 mL of river water within 10 min, and the resulting water quality met the WHO drinking water standards, indicating this material's practical application for POU water disinfection.

Encapsulated Polyethyleneimine Enables Synchronous Nanostructure Construction and In Situ Functionalization of Nanofiltration Membranes

Highly permselective nanostructured membranes are desirable for the energy-efficient molecular sieving on the subnanometer scale. The nanostructure construction and charge functionalization of the membranes are generally carried out step by step through the conventional layer-by-layer coating strategy, which inevitably brings about a demanding contradiction between the permselective performance and process efficiency. For the first time, we report the concurrent construction of the well-defined molecular sieving architectures and tunable surface charges of nanofiltration membranes through precisely controlled release of the nanocapsule decorated polyethyleneimine and carbon dioxide. This novel strategy not only substantially shortens the fabrication process but also leads to impressive performance (permeance up to 37.4 L m^-2 h^-1 bar^-1 together with a rejection 98.7% for Janus Green B-511 Da) that outperforms most state-of-art nanofiltration membranes. This study unlocks new avenues to engineer next-generation molecular sieving materials simply, precisely, and cost efficiently.

Enhancing Chlorine Resistance and Water Permeability during Forward Osmosis Separation Using Superhydrophilic Materials with Conjugated Systems

Poor resistance to free chlorine severely impairs the service of conventional polyamide (PA) membrane in water treatment. Here we design a series of superhydrophilic aromatic sulfonate materials (ASMs) comprising successively increasing conjugated systems and ionizable groups (ASM-1, ASM-2, ASM-3) to develop a chlorine-resistant membrane via chemical modification. By altering the membrane physicochemical properties and surface structure, ASMs substantially improve the chlorine resistance and water permeability of membrane. With 0.5 M NaCl as the draw solution, all ASMs enhance membrane water fluxes by more than 60% relative to those of the nascent PA membrane in forward osmosis (FO) processes. After exposed to a 1000 ppm sodium hypochlorite solution for 2-8 h, the modified membranes exhibit smaller variations in FO performance than the PA membrane. Having the largest conjugated system and the most sulfonate groups, ASM-3 enables the membrane to sustain a chlorination strength of up to 8000 ppm·h with an insignificant NaCl loss during the FO process, surpassing other recently developed PA membranes in chlorine resistance. These results manifest that the combination of a large conjugated system and ionizable group is key for imbuing membrane with excellent chlorine resistance and water permeability.

"Button and Buttonhole" Supramolecular Structure Enables the Self-Healing Behaviors of Functionalized Poly(ether sulfone) Membranes for Osmotic Power Generation

Osmotic power generation has emerged as an advanced technology toward water-energy nexus to tackle global water pollution. It provides a sustainable use of salinity gradient from water resources yet encounters major obstacles caused by pressure-retarded osmosis (PRO) membrane fouling. Although membranes with good antifouling properties are widely studied, their antifouling functions are readily lost when scratches or detachments occur through physical damage during operation and chemical degradation by water and corrosive foulants. Consequently, it is important to develop antifouling membranes with autonomous self-healing capabilities. Herein, self-healable functionalized poly(ether sulfone) (PES) antifouling membranes have been fabricated via the sequential conjugation of the zwitterionic random copolymer [poly(1-(1-(1-adamantylcarbonyloxy)methyl)-3-vinylimidazolium bromide-co-1-(3-sulfopropyl)-3-vinylimidazolium-co-vinylamine)] (P(ADVI-co-SBVI-co-VA), abbreviated as PASV copolymer) and linear cyclodextrin polymer (LPCD) on polydopamine-preactivated PES supports. The self-healing behaviors rely on the judiciously designed "button-and-buttonhole" supramolecular network. Specifically, β-cyclodextrins in LPCD and adamantines in PASV act as "buttonholes" and "buttons", respectively. Under physical and chemical damages, the β-cyclodextrin "buttonhole" may sacrificially detach from the adamantine "button" of PASV but then recap another adamantine to restore the protective function. The antifouling and self-healing traits of as-functionalized PES-g-PASV-LPCD membranes were demonstrated by the superior antiprotein behaviors and improved antimicrobial performances on both nonaged and aged samples. In the PRO process, the modified membranes were effective in mitigating organic fouling and exhibited higher power density (79% of the initial value) than the nonmodified ones (47% of the initial value) in municipal wastewater testing. The strategy for engineering inherently healable and antifouling membranes paves a new pathway for the development of sustainable membranes for osmotic power production.