Aggregate Morphology and Aqueous Dispersibility of Spray-Dried Powders of Cellulose Nanocrystals

Effect of different pre-treatments on the redispersion capacity of spray-dried microfibrillated cellulose: Elaboration and characterization of biofilms

This study aimed to evaluate the influence of the addition of the cationic surfactant cetyltrimethylammonium bromide (CTAB) in microfibrillated cellulose (MFC/CNFs) suspensions submitted to different pretreatments to produce redispersible spray-dried (SD) MFC/CNFs. Suspensions pretreated with 5 % and 10 % sodium silicate and oxidized with 2,2,6,6,-tetramethylpiperidinyl-1-oxyl (TEMPO) were modified with CTAB surfactant and subsequently dried by SD. The SD-MFC/CNFs aggregates were redispersed by ultrasound to produce cellulosic films by the casting method. In summary, the results demonstrated that the addition of CTAB surfactant to the TEMPO-oxidized suspension was critical to achieving the most effective redispersion. The experimental results obtained using micrographs, optical (UV-Vis), mechanical, water vapor barrier properties, and the quality index confirmed that the addition of CTAB to the TEMPO-oxidized suspension favored the redispersion of spray-dried aggregates, development of cellulosic films with attractive properties, offering possibilities for the elaboration of new products, for example, in the production of bionanocomposites with higher mechanical performance. This research brings interesting insights into the redispersion and application of SD-MFC/CNFs aggregates, strengthening the commercialization of MFC/CNFs for industrial use.

Corrugated surface microparticles with chitosan and levofloxacin for improved aerodynamic performance

Corrugated surface microparticles comprising levofloxacin (LEV), chitosan and organic acid were prepared using the 3-combo spray drying method. The amount and the boiling point of the organic acid affected the degree of roughness. In this study, we tried to improve the aerodynamic performance and increase aerosolization by corrugated surface microparticle for lung drug delivery efficiency as dry powder inhaler. HMP175 L20 prepared with 175 mmol propionic acid solution was corrugated more than HMF175 L20 prepared with 175 mmol formic acid solution. The ACI and PIV results showed a significant increase in aerodynamic performance of corrugated microparticles. The FPF value of HMP175 L20 was 41.3% ± 3.9% compared with 25.6% ± 7.7% of HMF175 L20. Corrugated microparticles also showed better aerosolization, decreased x-axial velocity, and variable angle. Rapid dissolution of drug formulations was observed in vivo. Low doses administered to the lungs achieved higher LEV concentrations in the lung fluid than high doses administered orally. Surface modification in the polymer-based formulation was achieved by controlling the evaporation rate and improving the inhalation efficiency of DPIs.

Nanoengineering the Redispersibility of Cellulose Nanocrystals

Enhancing the redispersibility of dried colloidal particles to yield stable dispersions after rehydration is a persistent challenge in the sustainable processing of nanocelluloses due to hydrogen bonding-induced irreversible aggregation. Programming nanocelluloses, such as cellulose nanocrystals (CNC), with moieties that enable colloidal repulsion after rehydration may address this challenge and contribute to the United Nation (UN)'s sustainable development goals (SDGs) of urban development and sustainable living (SDGs 9 and 11) and cradle-to-cradle processing (SDG 12). We hypothesize that imparting electrosteric repulsion to CNC via polyanionic disordered cellulose chains (hairs) protruding from each end may render the dried nanocrystals highly redispersible in aqueous media. Anionic hairy CNC (AHCNC), that is, CNC decorated with dicarboxylated cellulose (DCC) chains, were synthesized by the preferential, successive periodate/chlorite oxidation of the disordered regions of cellulose fibrils, bearing >5 mmol of carboxylate groups per gram. The colloidal properties of AHCNC were compared with those of sulfate half-ester group-functionalized CNC and TEMPO-oxidized CNC (TOCNC) after redispersion in aqueous media, followed by comparing the redispersibility of AHCNC and CNC in aqueous solutions containing monovalent or divalent cations and at varying pH. The AHCNC had remarkable aqueous redispersibility even at high ionic strengths and extreme pH. The unique redispersibility mechanism of dried AHCNC relies on the synergistic steric and electrostatic repulsion forces, recuperated upon the rehydration of DCC. This work may open new opportunities for more sustainable and cost-effective handling and processing of nanocelluloses.

Redispersion of dried plant nanocellulose: A review

Nanocellulose has undergone substantial development as a high value-added cellulose product with broad applications. Dried products are advantageous to decrease transportation costs. However, dried nanocellulose has redispersion challenges when rewetting. In this work, drying techniques, factors affecting redispersibility, and strategies improving the nanocellulose redispersibility are comprehensively reviewed. Hydrogen bonds of nanocellulose are unavoidably developed during drying, leading to inferior redispersibility of dried nanocellulose, even hornification. Drying processes of nanocellulose are discussed first. Then, factors affecting redispersibility are discussed. Following that, strategies improving the nanocellulose redispersibility are analyzed and their advantages and disadvantages are highlighted. Surface charge modification and steric hindrance concept are two main pathways to overcome the redispersion challenge, which are mainly carried out by chemical modification, additive incorporation and non-cellulosic component preservation. Despite several advancements having been achieved, new approaches for enhancing the nanocellulose redispersibility are still required to promote the industrial-scale applications of nanocellulose in various domains.

Microwave-Assisted Vacuum Synthesis of TiO2 Nanocrystalline Powders in One-Pot, One-Step Procedure

A new method for fast and simple synthesis of crystalline TiO2 nanoparticles with photocatalytic activity was developed by carrying out a classic sol-gel reaction directly under vacuum. The use of microwaves for fast heating of the reaction medium further reduces synthesis times. When the solvent is completely removed by vacuum, the product is obtained in the form of a powder that can be easily redispersed in water to yield a stable nanoparticle suspension, exhibiting a comparable photocatalytic activity with respect to a commercial product. The present methodology can, therefore, be considered a process intensification procedure for the production of nanotitania.

Quantification of energy input required for chitin nanocrystal aggregate size reduction through ultrasound

Nanoparticles have been claimed to contribute efficiently to e.g. the mechanical strength of composite materials when present as individual particles. However, these particles tend to aggregate. In this paper we prepare nanocrystals from chitin, a product with high potential added value for application in bio-based materials, and investigate the effect of ultrasound on de-aggregation. Chitin nanocrystals with a length ~ 200 nm and a diameter ~ 15 nm, were obtained via acid hydrolysis of crude chitin powder. Freeze drying resulted in severe aggregation and after redispersion sizes up to ~ 200 µm were found. Ultrasound treatment was applied and break up behaviour was investigated using static light scattering, dynamic light scattering, and laser diffraction. Our results suggest that the cumulative energy input was the dominant factor for chitin nanocrystal aggregate breakup. When a critical energy barrier of ~ 100 kJ/g chitin nanocrystals was exceeded, the chitin nanocrystal aggregates broke down to nanometre range. The break up was mostly a result of fragmentation: the aggregation energy of chitin nanocrystal aggregates was quantified to be ~ 370 kJ/g chitin nanocrystals and we hypothesize that mainly van der Waals interactions and hydrogen bonds are responsible for aggregation.

Cellulose nanocrystals in cancer diagnostics and treatment

Cancer is currently a major threat to public health, being among the principal causes of death to the global population. With carcinogenesis mechanisms, cancer invasion, and metastasis remaining blurred, cancer diagnosis and novel drug delivery approaches should be developed urgently to enable management and treatment. A dream break-through would be a non-invasive instantaneous monitoring of cancer initiation and progression to fast-track diagnosis for timely specialist treatment decisions. These innovations would enhance the established treatment protocols, unlimited by evasive biological complexities during tumorigenesis. It is therefore contingent that emerging and future scientific technologies be equally biased towards such innovations by exploiting the apparent properties of new developments and materials especially nanomaterials. CNCs as nanomaterials have undisputable physical and excellent biological properties that enhanced their interest as biomedical materials. This article therefore highlights CNCs utility in cancer diagnosis and therapy. Their extraction, properties, modification, in-vivo/in-vitro medical applications, biocompatibility, challenges and future perspectives are precisely discussed.

Particle Size Determines the Shape of Supraparticles in Self-Lubricating Ternary Droplets

Supraparticles are large clusters of much smaller colloidal particles. Controlling the shape and anisotropy of supraparticles can enhance their functionality, enabling applications in fields such as optics, magnetics, and medicine. The evaporation of self-lubricating colloidal ouzo droplets is an easy and efficient strategy to create supraparticles, overcoming the problem of the "coffee-stain effect" during drop evaporation. Yet, the parameters that control the shape of the supraparticles formed in such evaporating droplets are not fully understood. Here, we show that the size of the colloidal particles determines the shape of the supraparticle. We compared the shape of the supraparticles made of seven different sizes of spherical silica particles, namely from 20 to 1000 nm, and of the mixtures of small and large colloidal particles at different mixing ratios. Specifically, our in situ measurements revealed that the supraparticle formation proceeds via the formation of a flexible shell of colloidal particles at the rapidly moving interfaces of the evaporating droplet. The time t_c0 when the shell ceases to shrink and loses its flexibility is closely related to the size of particles. A lower t_c0, as observed for smaller colloidal particles, leads to a flat pancake-like supraparticle, in contrast to a more curved American football-like supraparticle from larger colloidal particles. Furthermore, using a mixture of large and small colloidal particles, we obtained supraparticles that display a spatial variation in particle distribution, with small colloids forming the outer surface of the supraparticle. Our findings provide a guideline for controlling the supraparticle shape and the spatial distribution of the colloidal particles in supraparticles by simply self-lubricating ternary drops filled with colloidal particles.

Polymer Induced Gelation of Aqueous Suspensions of Cellulose Nanocrystals

We investigated the gelation of cellulose nanocrystals (CNCs) in polyelectrolyte and neutral polymer solutions. Cellulose nanocrystals (CNCs) with half-ester sulfate groups produced by acid hydrolysis of wood pulp were used in this study. The microstructure of CNCs/polymer suspensions was investigated in semidilute concentration regimes by selecting carboxymethyl cellulose (CMC700) as an anionic polymer and poly(ethylene oxide) (PEO600) as a neutral polymer solution. Together with quartz crystal microbalance with dissipation monitoring (QCM-D), rheology, scanning electron microscopy (SEM), and cryo-transmission electron microscopy (cryo-TEM), we characterized CNCs-polymer interactions, the suspension microstructure, and the macroscopic gel flow. Significant viscosity increases at low shear rates coupled with high shear-thinning behaviors were observed in CNC colloid-CMC700 polymer mixtures, but not those CNCs in PEO600 solutions. The apparent differences between CNCs-CMC700 and CNCs-PEO600 mixtures were due to their chain confirmations. On the basis of the evaluations from STEM, cryo-TEM, and polarized optical microscopy, we proposed that the excess CMC700 molecules in solutions result in the depletion of CNCs and the formation of anisotropic domains.

Coupled Effects of Fibril Width, Residual and Mechanically Liberated Lignin on the Flow, Viscoelasticity, and Dewatering of Cellulosic Nanomaterials

The rheological behavior of aqueous suspensions of lignocellulose nanofibrils (LCNFs) is investigated systematically by considering the coupled effect of residual lignin and LCNF morphology. The LCNF was obtained by high-energy fluidization of TEMPO-oxidized mechanical fibers, followed by size fractionation (fibril widths of ∼5, ∼9, and ∼18 nm). The nanofibril width and the corresponding fibril-fibril interactions are strongly influenced by the presence and distribution of lignin in the respective fractions, either retained on the fibril surface or as free structures present in the finest size fraction. All samples containing lignin display dilatancy, typifying gel suspensions with aggregated hydrophobic particles. Fine fractionated samples display strong gel behavior. The coarse fractionated sample, by contrast, shows a greater tendency to flocculate via entanglement and displays less gel-like characteristics; hence, it dewaters more freely.

The Effects of High Pressure and High Temperature in Semidilute Aqueous Cellulose Nanocrystal Suspensions

A semidilute cellulose nanocrystal suspension was tested for pressure, volume, temperature dependencies of its viscosity and density. The compression of a 2.0 wt % cellulose nanocrystal suspension under 5.0 MPa at room temperature resulted in morphological changes from istotropic to nematic form. However, at high temperature, high-pressure treatment caused desulfation and gelation. Those results have significant applications, not only as additives in drilling and fracturing fluids but also for the preparation of hydrogels.