Efficient and Tunable Three-Dimensional Functionalization of Fully Zwitterionic Antifouling Surface Coatings

PDMS-Based Hierarchical Superhydrophobic Fabric Coating Fabricated by Thermal Treatment and Electrostatic Flocking Technology

Superhydrophobic coatings have broad applications in a variety of industries. By using a low-surface-energy material and creating nanoscale roughness, a superhydrophobic surface can be produced. To overcome the health and environmental concerns of fluorine-based materials and the limitations of large-scale rough microstructure fabrication, a poly(dimethylsiloxane) (PDMS)-based hierarchical superhydrophobic fabric coating prepared by simple thermal treatment and electrostatic flocking technology was introduced in this study. High-temperature thermal treatment is employed to create PDMS nanoparticle-decorated carbon fibers, which are further vertically implanted onto the surface of cotton fabric via electrostatic flocking technology. The environmentally friendly PDMS nanoparticles were adopted as low-surface-energy materials, and the electrostatic flocking technology was utilized to generate a vertically aligned carbon fiber array coating, mimicking a lotus leaf-like superhydrophobic surface microstructure. Therefore, an ultrahigh water contact angle of 173.9 ± 2.8° and a low sliding angle of 1 ± 0.5° can be obtained by the fabric coating with a PDMS-to-carbon fiber ratio of 20:1. The prepared superhydrophobic fabric also exhibits an excellent self-cleaning property and great durability after 60 cycles of washing. Through commercially available thermal treatment and electrostatic flocking processes, this strategy for fabricating fluorine-free superhydrophobic fabric can be easily scaled up for commercial manufacturing and promotes the design of superhydrophobic coatings for other substrates.

Capturing Enzyme-Loaded Diblock Copolymer Vesicles Using an Aldehyde-Functionalized Hydrophilic Polymer Brush

Compared to lipids, block copolymer vesicles are potentially robust nanocontainers for enzymes owing to their enhanced chemical stability, particularly in challenging environments. Herein we report that cis-diol-functional diblock copolymer vesicles can be chemically adsorbed onto a hydrophilic aldehyde-functional polymer brush via acetal bond formation under mild conditions (pH 5.5, 20 °C). Quartz crystal microbalance studies indicated an adsorbed amount, Γ, of 158 mg m-2 for vesicle adsorption onto such brushes, whereas negligible adsorption (Γ = 0.1 mg m-2) was observed for a control experiment conducted using a cis-diol-functionalized brush. Scanning electron microscopy and ellipsometry studies indicated a mean surface coverage of around 30% at the brush surface, which suggests reasonably efficient chemical adsorption. Importantly, such vesicles can be conveniently loaded with a model enzyme (horseradish peroxidase, HRP) using an aqueous polymerization-induced self-assembly formulation. Moreover, the immobilized vesicles remained permeable toward small molecules while retaining their enzyme payload. The enzymatic activity of such HRP-loaded vesicles was demonstrated using a well-established colorimetric assay. In principle, this efficient vesicle-on-brush strategy can be applied to a wide range of enzymes and functional proteins for the design of next-generation immobilized nanoreactors for enzyme-mediated catalysis.

Tunable Cell-Adhesive Surfaces by Surface-Initiated Photoinduced Electron-Transfer-Reversible Addition-Fragmentation Chain-Transfer Polymerization

Cell adhesion involves many interactions between various molecules on the cell membrane (receptors, coreceptors, integrins, etc.) and surfaces or other cells. Cell adhesion plays a crucial role in the analysis of immune response, cancer treatment, tissue engineering, etc. Cell-cell adhesion can be quantified by measuring cell avidity, which defines the total interaction strength of the live cell binding. Typically, those investigations use tailor-made, reusable chips or surfaces onto which cells are cultured to form a monolayer to which other cells can bind. Cell avidity can then be measured by applying a force and quantifying cell-cell bond ruptures. The subsequent cleaning and reactivation of such biochip and biointeractive surfaces often require repeated etching, leading to device damage. Furthermore, it is often of great interest to harvest the cells that remain bound at the end of an avidity experiment for further analysis or use. It is, therefore, advantageous to pursue coating methods that allow tunable cell adhesion. This work presents temperature-switchable poly(di(ethylene glycol) methyl ether methacrylate) brush-based cell-interactive coatings produced by surface-initiated photoinduced electron-transfer reversible addition-fragmentation chain-transfer polymerization. The temperature switch of these brushes was explored by using a quartz crystal microbalance with dissipation monitoring, chemical composition, and physicochemical properties by atom force microscopy, X-ray photoelectron spectroscopy, single-molecule force spectroscopy, and ellipsometry.

Integrated Electrochemical and Optical Biosensing in Organs-on-Chip

Demand for biocompatible, non-invasive, and continuous real-time monitoring of organs-on-chip has driven the development of a variety of novel sensors. However, highest accuracy and sensitivity can arguably be achieved by integrated biosensing, which enables in situ monitoring of the in vitro microenvironment and dynamic responses of tissues and miniature organs recapitulated in organs-on-chip. This paper reviews integrated electrical, electrochemical, and optical sensing methods within organ-on-chip devices and platforms. By affording precise detection of analytes and biochemical reactions, these methods expand and advance the monitoring capabilities and reproducibility of organ-on-chip technology. The integration of these sensing techniques allows a deeper understanding of organ functions, and paves the way for important applications such as drug testing, disease modeling, and personalized medicine. By consolidating recent advancements and highlighting challenges in the field, this review aims to foster further research and innovation in the integration of biosensing in organs-on-chip.

Design, preparation, and characterization of lubricating polymer brushes for biomedical applications

The lubrication modification of biomedical devices significantly enhances the functionality of implanted interventional medical devices, thereby providing additional benefits for patients. Polymer brush coating provides a convenient and efficient method for surface modification while ensuring the preservation of the substrate's original properties. The current research has focused on a "trial and error" method to finding polymer brushes with superior lubricity qualities, which is time-consuming and expensive, as obtaining effective and long-lasting lubricity properties for polymer brushes is difficult. This review summarizes recent research advances in the biomedical field in the design, material selection, preparation, and characterization of lubricating and antifouling polymer brushes, which follow the polymer brush development process. This review begins by examining various approaches to polymer brush design, including molecular dynamics simulation and machine learning, from the fundamentals of polymer brush lubrication. Recent advancements in polymer brush design are then synthesized and potential avenues for future research are explored. Emphasis is placed on the burgeoning field of zwitterionic polymer brushes, and highlighting the broad prospects of supramolecular polymer brushes based on host-guest interactions in the field of self-repairing polymer brush applications. The review culminates by providing a summary of methodologies for characterizing the structural and functional attributes of polymer brushes. It is believed that a development approach for polymer brushes based on "design-material selection-preparation-characterization" can be created, easing the challenge of creating polymer brushes with high-performance lubricating qualities and enabling the on-demand creation of coatings. STATEMENT OF SIGNIFICANCE: Biomedical devices have severe lubrication modification needs, and surface lubrication modification by polymer brush coating is currently the most promising means. However, the design and preparation of polymer brushes often involves "iterative testing" to find polymer brushes with excellent lubrication properties, which is both time-consuming and expensive. This review proposes a polymer brush development process based on the "design-material selection-preparation-characterization" strategy and summarizes recent research advances and trends in the design, material selection, preparation, and characterization of polymer brushes. This review will help polymer brush researchers by alleviating the challenges of creating polymer brushes with high-performance lubricity and promises to enable the on-demand construction of polymer brush lubrication coatings.

Zwitterionic polymer on silicone implants inhibits the bacteria-driven pathogenic mechanism and progress of breast implant-associated anaplastic large cell lymphoma

Breast implant-associated anaplastic large cell lymphoma (BIA-ALCL) occurs in the capsule surrounding breast implants. Malignant transformation of T cells by bacteria-driven chronic inflammation may be underlying BIA-ALCL mechanism. Here, we covalently grafted 2-methacryloyloxyethyl phosphorylcholine (MPC)-based polymers on a silicone surface and examined its effects against BIA-ALCL pathogenesis. MPC grafting strongly inhibited the adhesion of bacteria and bacteria-causing inflammation. Additionally, cancer T cell proliferation and capsule-derived fibroblast-cancer cell communication were effectively inhibited by MPC grafting. We further demonstrated the effect of MPC against the immune responses causing BIA-ALCL around human silicone implants in micro-pigs. Finally, we generated a xenograft anaplastic T cell lymphoma mouse model around the silicone implants and demonstrated that MPC grafting could effectively inhibit the lymphoma progression. This study is the first to show that bacteria-driven induction and progression of BIA-ALCL can be effectively inhibited by surface modification of implants. STATEMENT OF SIGNIFICANCE: Breast implant-associated anaplastic large cell lymphoma (BIA-ALCL) is a major concern in the field of plastic and reconstructive surgery. In this study, we demonstrate strong inhibitory effect of zwitterionic polymer grafting on BIA-ALCL pathogenesis and progression, induced by bacterial infection and inflammation, both in vitro and in vivo. This study provides a molecular basis for the development of novel breast implants that can prevent various potential complications such as excessive capsular contracture, breast implant illness, and BIA-ALCL incidence, as well as for expanding the biomedical applications of zwitterionic polymers.

Antiviral Polymer Brushes by Visible-Light-Induced, Oxygen-Tolerant Covalent Surface Coating

This work presents a novel route for creating metal-free antiviral coatings based on polymer brushes synthesized by surface-initiated photoinduced electron transfer-reversible addition-fragmentation chain transfer (SI-PET-RAFT) polymerization, applying eosin Y as a photocatalyst, water as a solvent, and visible light as a driving force. The polymer brushes were synthesized using N-[3-(decyldimethyl)-aminopropyl] methacrylamide bromide and carboxybetaine methacrylamide monomers. The chemical composition, thickness, roughness, and wettability of the resulting polymer brush coatings were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), water contact angle measurements, and ellipsometry. The antiviral properties of coatings were investigated by exposure to severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) and avian influenza viruses, with further measurement of residual viable viral particles. The best performance was obtained with Cu surfaces, with a ca. 20-fold reduction of SARS-Cov-2 and a 50-fold reduction in avian influenza. On the polymer brush-modified surfaces, the number of viable virus particles decreased by about 5-6 times faster for avian flu and about 2-3 times faster for SARS-CoV-2, all compared to unmodified silicon surfaces. Interestingly, no significant differences were obtained between quaternary ammonium brushes and zwitterionic brushes.

Impact of Membrane Modification and Surface Immobilization Techniques on the Hemocompatibility of Hemodialysis Membranes: A Critical Review

Despite significant research efforts, hemodialysis patients have poor survival rates and low quality of life. Ultrafiltration (UF) membranes are the core of hemodialysis treatment, acting as a barrier for metabolic waste removal and supplying vital nutrients. So, developing a durable and suitable membrane that may be employed for therapeutic purposes is crucial. Surface modificationis a useful solution to boostmembrane characteristics like roughness, charge neutrality, wettability, hemocompatibility, and functionality, which are important in dialysis efficiency. The modification techniques can be classified as follows: (i) physical modification techniques (thermal treatment, polishing and grinding, blending, and coating), (ii) chemical modification (chemical methods, ozone treatment, ultraviolet-induced grafting, plasma treatment, high energy radiation, and enzymatic treatment); and (iii) combination methods (physicochemical). Despite the fact that each strategy has its own set of benefits and drawbacks, all of these methods yielded noteworthy outcomes, even if quantifying the enhanced performance is difficult. A hemodialysis membrane with outstanding hydrophilicity and hemocompatibility can be achieved by employing the right surface modification and immobilization technique. Modified membranes pave the way for more advancement in hemodialysis membrane hemocompatibility. Therefore, this critical review focused on the impact of the modification method used on the hemocompatibility of dialysis membranes while covering some possible modifications and basic research beyond clinical applications.

Highly Specific Protein Identification by Immunoprecipitation-Mass Spectrometry Using Antifouling Microbeads

A common method to study protein complexes is immunoprecipitation (IP), followed by mass spectrometry (thus labeled: IP-MS). IP-MS has been shown to be a powerful tool to identify protein-protein interactions. It is, however, often challenging to discriminate true protein interactors from contaminating ones. Here, we describe the preparation of antifouling azide-functionalized polymer-coated beads that can be equipped with an antibody of choice via click chemistry. We show the preparation of generic immunoprecipitation beads that target the green fluorescent protein (GFP) and show how they can be used in IP-MS experiments targeting two different GFP-fusion proteins. Our antifouling beads were able to efficiently identify relevant protein-protein interactions but with a strong reduction in unwanted nonspecific protein binding compared to commercial anti-GFP beads.

Thermoplastic zwitterionic elastomer with critical antifouling properties

Thermoplastic elastomers are widely used in the medical industry for advanced medical and healthcare products, helping millions of patients achieve a better quality of life. Yet, microbial contamination and material-associated biofilms on devices remain a critical challenge because it is challenging for currently available materials to provide critical antifouling properties, thermoplasticity, and elastic properties simultaneously. We developed a highly flexible zwitterionic thermoplastic polyurethane with critical antifouling properties. A series of poly((diethanolamine ethyl acetate)-co-poly(tetrahydrofuran)-co-(1,6-diisocyanatohexane)) (PCB-PTHFUs) were synthesized. The PCB-PTHFUs exhibit a breaking strain of more than 400%, a high resistance to fibroblast cells for 24 h, and the excellent ability to prevent biofilm formation for up to three weeks. This study lays a foundation for clarifying the structure-function relationships of zwitterionic polymers. This thermoplastic PCB-PTHFU platform, with its unmatched antifouling properties and high elasticity, has potential for implanted medical devices and a broad spectrum of applications that suffer from biofouling, such as material-associated infection.

Ultralow-Fouling Zwitterionic Polyurethane-Modified Membranes for Rapid Separation of Plasma from Whole Blood

The separation of plasma from blood cells in whole blood is an essential step for many diagnostic and therapeutic applications. However, the current point-of-care plasma separation approaches have not yet satisfied the need for a rapid, high-flux, and low-cost process. Here, we report a portable, low-cost, disposable membrane-based plasma separation device that enables rapid plasma extraction from whole blood. Rapid separation of plasma can be obtained with a simple three-step operation: blood injection, separation, and plasma collection. Our device benefits from the zwitterionic polyurethane-modified cellulose acetate (PCBU-CA) membrane, which can greatly inhibit the surface fouling of blood cells and membrane flux decline. The zwitterionic coating is stable on the membrane surface during blood filtration and leads to a 60% decrease in surface fibrinogen adsorption than a nonmodified membrane surface. The ultralow-blood-fouling properties of the PCBU-CA membrane enable rapid, continuous separation of plasma: within 10 min, the device can yield 0.5-0.7 mL of plasma from 10 mL of whole blood. The extracted plasma is verified as cell-free, exhibits a low hemoglobin level, and has a high protein recovery. Our PCBU-CA membrane provides a pathway for developing a high-efficiency portable plasma separation device that can reduce the time to diagnosis, allow effective patient care, and eventually reduce hospital costs.

Plant-inspired quercetin thin films: universal coatings and their postfunctionalization for non-biofouling applications

We developed quercetin surface chemistry that can be applied for various substrates and is able to postfunctionalize for hemocompatible coatings.

Open-to-Air RAFT Polymerization on a Surface under Ambient Conditions

Oxygen (O₂)-mediated controlled radical polymerization was performed on surfaces under ambient conditions, enabling on-surface polymer brush growth under open-to-air conditions at room temperature in the absence of metal components. Polymerization of zwitterionic monomers using this O₂-mediated surface-initiated reversible addition fragmentation chain-transfer (O₂-SI-RAFT) method yielded hydrophilic surfaces that exhibited anti-biofouling effects. O₂-SI-RAFT polymerization can be performed on large surfaces under open-to-air conditions. Various monomers including (meth)acrylates and acrylamides were employed for O₂-SI-RAFT polymerization; the method is thus versatile in terms of the polymers used for coating and functionalization. A wide range of hydrophilic and hydrophobic monomers can be employed. In addition, the end-group functionality of the polymer grown by O₂-SI-RAFT polymerization allowed chain extension to form block copolymer brushes on a surface.

PLL-Poly(HPMA) Bottlebrush-Based Antifouling Coatings: Three Grafting Routes

In this work, we compare three routes to prepare antifouling coatings that consist of poly(l-lysine)-poly(N-(2-hydroxypropyl)methacrylamide) bottlebrushes. The poly(l-lysine) (PLL) backbone is self-assembled onto the surface by charged-based interactions between the lysine groups and the negatively charged silicon oxide surface, whereas the poly(N-(2-hydroxypropyl)methacrylamide) [poly(HPMA)] side chains, grown by reversible addition-fragmentation chain-transfer (RAFT) polymerization, provide antifouling properties to the surface. First, the PLL-poly(HPMA) coatings are synthesized in a bottom-up fashion through a grafting-from approach. In this route, the PLL is self-assembled onto a surface, after which a polymerization agent is immobilized, and finally HPMA is polymerized from the surface. In the second explored route, the PLL is modified in solution by a RAFT agent to create a macroinitiator. After self-assembly of this macroinitiator onto the surface, poly(HPMA) is polymerized from the surface by RAFT. In the third and last route, the whole PLL-poly(HPMA) bottlebrush is initially synthesized in solution. To this end, HPMA is polymerized from the macroinitiator in solution and the PLL-poly(HPMA) bottlebrush is then self-assembled onto the surface in just one step (grafting-to approach). Additionally, in this third route, we also design and synthesize a bottlebrush polymer with a PLL backbone and poly(HPMA) side chains, with the latter containing 5% carboxybetaine (CB) monomers that eventually allow for additional (bio)functionalization in solution or after surface immobilization. These three routes are evaluated in terms of ease of synthesis, scalability, ease of characterization, and a preliminary investigation of their antifouling performance. All three coating procedures result in coatings that show antifouling properties in single-protein antifouling tests. This method thus presents a new, simple, versatile, and highly scalable approach for the manufacturing of PLL-based bottlebrush coatings that can be synthesized partly or completely on the surface or in solution, depending on the desired production process and/or application.

A new ultralow fouling surface for the analysis of human plasma samples with surface plasmon resonance

Surface plasmon resonance (SPR) has been widely used to detect a variety of biomolecular systems, but only a small fraction of applications report on the analysis of patients' samples. A critical barrier to the full implementation of SPR technology in molecular diagnostics currently exists for its potential application to analyze blood plasma or serum samples. Such capability is mostly hindered by the non-specific adsorption of interfering species present in the biological sample at the functional interface of the biosensor, often referred to as fouling. Suitable polymeric layers having a thickness ranging from 15 and about 70 nm are usually deposited on the active surface of biosensors to introduce antifouling properties. A similar approach is not fully adequate for SPR detection where the exponential decay of the evanescent plasmonic field limits the thickness of the layer beyond the SPR metallic sensor surface for which a sensitive detection can be obtained. Here, a triethylene glycol (PEG(3))-pentrimer carboxybetaine system is proposed to fabricate a new surface coating bearing excellent antifouling properties with a thickness of less than 2 nm, thus compatible with sensitive SPR detection. The high variability of experimental conditions described in the literature for the quantitative assessment of the antifouling performances of surface layers moved us to compare the superior antifouling capacity of the new pentrimeric system with that of 4-aminophenylphosphorylcholine, PEG-carboxybetaine and sulfobetaine-modified surface layers, respectively, using undiluted and diluted pooled human plasma samples. The use of the new coating for the immunologic SPRI biosensing of human arginase 1 in plasma is also presented.

Functional Molecular Interfaces for Impedance-Based Diagnostics

In seeking to develop and optimize reagentless electroanalytical assays, a consideration of the transducing interface features lies key to any subsequent sensitivity and selectivity. This review briefly summarizes some of the most commonly used receptive interfaces that have been employed within the development of impedimetric molecular sensors. We discuss the use of high surface area carbon, nanoparticles, and a range of bioreceptors that can subsequently be integrated. The review spans the most commonly utilized biorecognition elements, such as antibodies, antibody fragments, aptamers, and nucleic acids, and touches on some novel emerging alternatives such as nanofragments, molecularly imprinted polymers, and bacteriophages. Reference is made to the immobilization chemistries available along with a consideration of both optimal packing density and recognition probe orientation. We also discuss assay-relevant mechanistic details and applications in real sample analysis.

Supramolecular Additive-Initiated Controlled Atom Transfer Radical Polymerization of Zwitterionic Polymers on Ureido-pyrimidinone-Based Biomaterial Surfaces

Surface-initiated controlled radical polymerization is a popular technique for the modification of biomaterials with, for example, antifouling polymers. Here, we report on the functionalization of a supramolecular biomaterial with zwitterionic poly(sulfobetaine methacrylate) via atom transfer radical polymerization from a macroinitiator additive, which is embedded in the hard phase of the ureido-pyrimidinone-based material. Poly(sulfobetaine methacrylate) was successfully polymerized from these surfaces, and the polymerized sulfobetaine content, with corresponding antifouling properties, depended on both the macroinitiator additive concentration and polymerization time. Furthermore, the polymerization from the macroinitiator additive was successfully translated to functional electrospun scaffolds, showing the potential for this functionalization strategy in supramolecular material systems.

An electrospun polyurethane scaffold-reinforced zwitterionic hydrogel as a biocompatible device

An electrospun scaffold-reinforced zwitterionic hydrogel achieved both high tensile strength and mechano-induced self-enhancement while maintaining excellent hemocompatibility.

Combinatorial functionalization with bisurea-peptides and antifouling bisurea additives of a supramolecular elastomeric biomaterial

The bioactive additive toolbox to functionalize supramolecular elastomeric materials expands rapidly. Here we have set an explorative step toward screening of complex combinatorial functionalization with antifouling and three peptide-containing additives in a bisurea-based supramolecular system. Thorough investigation of surface properties of thin films with contact angle measurements, X-ray photoelectron spectroscopy and atomic force microscopy, was correlated to cell-adhesion of endothelial and smooth muscle cells to apprehend their respective predictive values for functional biomaterial development. Peptides were presented at the surface alone, and in combinatorial functionalization with the oligo(ethylene glycol)-based non-cell adhesive additive. The bisurea-RGD additive was cell-adhesive in all conditions, whereas the endothelial cell-specific bisurea-REDV showed limited bioactive properties in all chemical nano-environments. Also, aspecific functionality was observed for a bisurea-SDF1α peptide. These results emphasize that special care should be taken in changing the chemical nano-environment with peptide functionalization. © 2019 The Authors. Journal of Polymer Science Part B: Polymer Physics published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019, 57, 1725-1735.

Dual-Mode Electrochemical Assay of Prostate-Specific Antigen Based on Antifouling Peptides Functionalized with Electrochemical Probes and Internal References

Sensitive and selective detection of target analytes in complex biological samples is currently a major challenge. Herein we constructed a dual-mode antifouling electrochemical sensing platform for the detection of prostate-specific antigen (PSA) based on two kinds of antifouling peptides functionalized with a graphene oxide-Fe₃O₄-thionine (GO-Fe₃O₄-Thi) probe and internal reference ferrocene (Fc), respectively. The longer peptide (Pep1) modified with the GO-Fe₃O₄-Thi probe was designed to contain a peptide sequence (HSSKLQK) capable of being recognized and cut by PSA. The GO-Fe₃O₄-Thi probe functions not only as a peroxidase mimick (GO-Fe₃O₄) but also works as an electrochemical probe due to the presence of thionine (Thi). The concentration of PSA can be measured through both the increase of differential pulse voltammetry (DPV) signal change of Thi and the decrease of chronoamperometry (CA) signal of the reduction of H₂O₂ electrocatalyzed by GO-Fe₃O₄. The shorter peptide (Pep2) was tagged with Fc, whose DPV signal remained constant and was independent of the presence of PSA, and it was used as an internal reference to ensure the reliability and accuracy of the measurement. The dual-mode PSA sensor exhibits a wide linear range from 5 pg/mL to 10 ng/mL, with low detection limits of 0.76 and 0.42 pg/mL through DPV and CA modes, respectively. More importantly, owing to the antifouling capability of the designed peptides, the biosensor performances remained operable even in human serum, indicating feasibility of the electrochemical biosensor for practical PSA quantification in complex samples.

Thermo-responsive polymers: Applications of smart materials in drug delivery and tissue engineering

Synthetic polymers are attracting great attention in the last decades for their use in the biomedical field as nanovectors for controlled drug delivery, hydrogels and scaffolds enabling cell growth. Among them, polymers able to respond to environmental stimuli have been recently under growing consideration to impart a "smart" behavior to the final product, which is highly desirable to provide it with a specific dynamic and an advanced function. In particular, thermo-responsive polymers, materials able to undergo a discontinuous phase transition or morphological change in response to a temperature variation, are among the most studied. The development of the so-called controlled radical polymerization techniques has paved the way to a high degree of engineering for the polymer architecture and properties, which in turn brought to a plethora of sophisticated behaviors for these polymers by simply switching the external temperature. These can be exploited in many different fields, from separation to advanced optics and biosensors. The aim of this review is to critically discuss the latest advances in the development of thermo-responsive materials for biomedical applications, including a highly controlled drug delivery, mediation of cell growth and bioseparation. The focus is on the structural and design aspects that are required to exploit such materials for cutting-edge applications in the biomedical field.

Electrochemical aptasensor based on conductive supramolecular polymer hydrogels for thrombin detection with high selectivity

Herein, we synthesized a kind of conductive supramolecular polymer hydrogel (CSPH) based on polyaniline (PANI) which can not only improve the conductivity but also promote antifouling performance of the aptasensor for the specific recruitment of thrombin (TB) from complex samples. With the electrochemical copolymerization of aniline (AN) and 3-aminophenylboronic acid (ABA) on glassy carbon electrode (GCE), the electrode was then inserted into the polyvinyl alcohol (PVA) solution to obtain robust CSPH through boric acid groups incorporated onto PANI to cause gelation of PVA solution, owing to the hydrophilicity of CSPH and nearly electrical neutrality, the modified electrode is antifouling without integration of other antifouling materials. A sandwich-type electrochemical aptasensor was constructed on the CSPH based electrode interfaces. Thrombin aptamer 1 (TBA1) were modified on the CSPH through amide bond, and thrombin aptamer 2 modified magnetic nanoparticles (MNP-TBA2) are used as signal amplification probes, the aptasensor has good sensitivity with a linear range from 1 pmol/L to 10 nmol/L and has a detection limit down to 0.64 pmol/L. The strategy of utilizing eletropolymerization of CSPH films to undergo highly selective thrombin recognition is, of course, readily extended to a broad range of targets in the real samples, and the recovery was ranging from 95.2% to 106.3% and RSDs varying from 2.3% to 4.5%.

Artificial Microbial Arenas: Materials for Observing and Manipulating Microbial Consortia

From the smallest ecological niche to global scale, communities of microbial life present a major factor in system regulation and stability. As long as laboratory studies remain restricted to single or few species assemblies, however, very little is known about the interaction patterns and exogenous factors controlling the dynamics of natural microbial communities. In combination with microfluidic technologies, progress in the manufacture of functional and stimuli-responsive materials makes artificial microbial arenas accessible. As habitats for natural or multispecies synthetic consortia, they are expected to not only enable detailed investigations, but also the training and the directed evolution of microbial communities in states of balance and disturbance, or under the effects of modulated stimuli and spontaneous response triggers. Here, a perspective on how materials research will play an essential role in generating answers to the most pertinent questions of microbial engineering is presented, and the concept of adaptive microbial arenas and possibilities for their construction from particulate microniches to 3D habitats is introduced. Materials as active and tunable components at the interface of living and nonliving matter offer exciting opportunities in this field. Beyond forming the physical horizon for microbial cultivates, they will enable dedicated intervention, training, and observation of microbial consortia.

Systematic Comparison of Zwitterionic and Non-Zwitterionic Antifouling Polymer Brushes on a Bead-Based Platform

Nonspecific adsorption of biomolecules to solid surfaces, a process called biofouling, is a major concern in many biomedical applications. Great effort has been made in the development of antifouling polymer coatings that are capable of repelling the nonspecific adsorption of proteins, cells, and micro-organisms. In this respect, we herein contribute to understanding the factors that determine which polymer brush results in the best antifouling coating. To this end, we compared five different monomers: two sulfobetaines, a carboxybetaine, a phosphocholine, and a hydroxyl acrylamide. The antifouling coatings were analyzed using our previously described bead-based method with flow cytometry as the read-out system. This method allows for the quick and automated analysis of thousands of beads per second, enabling fast analysis and good statistics. We report the first direct comparison made between a sulfobetaine with opposite charges separated by two and three methylene groups and a carboxybetaine bearing two separating methylene groups. It was concluded that both the distance between opposite charges and the nature of the anionic groups have a distinct effect on the antifouling performance. Phosphocholines and simple hydroxyl acrylamides are not often compared with the betaines. However, here we found that they perform equally well or even better, yielding the following overall antifouling ranking: HPMAA ≥ PCMA-2 ≈ CBMAA-2 > SBMAA-2 > SBMAA-3 ≫ nonmodified beads (HPMAA being the best).

Molecular Design of Zwitterionic Polymer Interfaces: Searching for the Difference

The widespread occurrence of zwitterionic compounds in nature has incited their frequent use in designing biomimetic materials. Therefore, zwitterionic polymers are a thriving field. A particular interest for this particular polymer class has currently focused on their use in establishing neutral, low-fouling surfaces. After highlighting strategies to prepare model zwitterionic surfaces as well as those that are more suitable for practical purposes relying strongly on radical polymerization methods, we present recent efforts to diversify the structure of the hitherto quite limited variety of zwitterionic monomers and of the derived polymers. We identify key structural variables, consider their influence on essential properties such as overall hydrophilicity and long-term stability, and discuss promising targets for the synthesis of new variants.

Low-Fouling Characteristics of Ultrathin Zwitterionic Cysteine SAMs

Surface fouling remains an exigent issue for many biological implants. Unwanted solutes adsorb to reduce device efficiency and hasten degradation while increasing the risks of microbial colonization and adverse inflammatory response. To address unwanted fouling in modern implants in vivo, surface modification with antifouling polymers has become indispensable. Recently, zwitterionic self-assembled monolayers, which contain two or more charged functional groups but are electrostatically neutral and form highly hydrated surfaces, have been the focus of many antifouling coatings. Reports using various compositions of zwitterionic polymer brushes have demonstrated ultralow fouling in the ng/cm² range. These coatings, however, are thick and can hinder the target application of biological devices. Here, we report an ultrathin (8.52 Å) antifouling self-assembled monolayer composed of cysteine that is amenable to facile fabrication. The antifouling characteristics of the zwitterionic surfaces were evaluated against bovine serum albumin, fibrinogen, and human blood in real time using quartz crystal microbalance and surface plasmon resonance imaging. Compared to untreated gold surfaces, the ultrathin cysteine coating reduced the adsorption of bovine serum albumin by 95% (43 ng/cm² adsorbed) after 3 h and 90% reduction after 24 h. Similarly, the cysteine self-assembled monolayer reduced the adsorption of fibrinogen as well as human blood by >90%. The surfaces were further characterized using scanning electron microscopy: protein-enhanced adsorption and cellular adsorption in human blood was found on untreated surfaces but not on the cysteine SAM-protected surfaces. These findings suggest that surfaces can be functionalized with an ultrathin layer of cysteine to resist the adsorption of key proteins, with performance comparable to zwitterionic polymer brushes. As such, cysteine surface coatings are a promising methodology to improve the long-term utility of biological devices.

Low-Fouling Thin Hydrogel Coatings Made of Photo-Cross-Linked Polyzwitterions

Although zwitterionic chemistries are among the most promising materials for producing nonfouling surfaces, their structural diversity has been low until now. Here, we compare the in vitro fouling behavior of a set of four systematically varied sulfa-/sulfobetaine-containing zwitterionic hydrogel coatings against a series of proteins and nonmotile as well as motile marine organisms as model foulers. The coatings are prepared by simultaneous photoinduced cross-linking and surface anchoring to elucidate the effect of the molecular structure of the zwitterionic moieties on their antifouling activity. Analogously prepared coatings of poly(butyl methacrylate) and poly(oligoethylene glycol methacrylate) serve as references. Photoreactive polymers are synthesized by the statistical copolymerization of sulfobetaine or sulfabetaine methacrylates and methacrylamides with a benzophenone derivative of 2-hydroxyethyl methacrylate and are applied as a thin film coating. While keeping the density of the zwitterionic and cross-linker groups constant, the molecular structure of the zwitterionic side chains is varied systematically, as is the arrangement of the ion pairs in the side chain by changing the classical linear geometry to a novel Y-shaped geometry. All of the polyzwitterions strongly reduce fouling compared to poly(butyl methacrylate). Overall, the sulfabetaine polyzwitterion coatings studied matches the high antifouling effectiveness of oligo(ethylene glycol)-based ones used as a control. Nevertheless, performances varied individually for a given pair of polymer and fouler. The case of the polysulfobetaines exemplifies that minor chemical changes in the polymer structure affect the antifouling performance markedly. Accordingly, the antifouling performance of such polymers cannot be correlated simply to the type of zwitterion used (which could be generally ranked as better performing or poorer performing) but is a result of the polymer's precise chemical structure. Our findings underline the need to enlarge the existing structural diversity of polyzwitterions for antifouling purposes to optimize the potential of their chemical structure.

Romantic Surfaces: A Systematic Overview of Stable, Biospecific, and Antifouling Zwitterionic Surfaces

This Feature Article focuses on recent advances in the bioconjugation of surface-bound zwitterionic polymers for biospecific antifouling surfaces. Various approaches for the functionalization of antifouling zwitterionic polymers are systematically investigated, such as chain-end and side-chain functionalization. Side-chain functionalization methods can be further classified as those that are achieved through homopolymerization of custom-synthesized zwitterionic monomers equipped with reactive groups, or those that are achieved via synthesis of random or block copolymers combining different monomers with antifouling functionality and others with reactive groups. Several of the pros and cons of these approaches are outlined and discussed. Finally, some perspective and future directions of research are presented toward long-term stable, generically repelling surfaces that strongly and specifically adhere to a single component in a complex mixture.

A switchable polymer brush system for antifouling and controlled detection

A stimuli-responsive polymer brush system is designed to switch on and off surface functionality and prevent functional groups from fouling by grafting together two polymer brushes with precisely controlled lengths. The polymer brush with functional groups has a fixed length, while the other brush extends and collapses as the environment changes.

Laccase-Mediated Grafting on Biopolymers and Synthetic Polymers: A Critical Review

Laccase-mediated grafting on lignocelluloses has gained considerable attention as an environmentally benign method to covalently modify wood, paper and cork. In recent decades this technique has also been employed to modify fibres with a polysaccharide backbone, such as cellulose or chitosan, to infer colouration, antimicrobial activity or antioxidant activity to the material. The scope of this approach has been further widened by researchers, who apply mediators or high redox potential laccases and those that modify synthetic polymers and proteins. In all cases, the methodology relies on one- or two-electron oxidation of the surface functional groups or of the graftable molecule in solution. However, similar results can very often be achieved through simple deposition, even after extensive washing. This unintended adsorption of the active substance could have an adverse effect on the durability of the applied coating. Differentiating between actual covalent binding and adsorption is therefore essential, but proves to be challenging. This review not only covers excellent research on the topic of laccase-mediated grafting over the last five to ten years, but also provides a critical comparison to highlight either the lack or presence of compelling evidence for covalent grafting.

Introduction of Nature's Complexity in Engineered Blood-compatible Biomaterials

Biomaterials with excellent blood-compatibility are needed for applications in vascular replacement therapies, such as vascular grafts, heart valves and stents, and in extracorporeal devices such as hemodialysis machines and blood-storage bags. The modification of materials that are being used for blood-contacting devices has advanced from passive surface modifications to the design of more complex, smart biomaterials that respond to relevant stimuli from blood to counteract coagulation. Logically, the main source of inspiration for the design of new biomaterials has been the endogenous endothelium. Endothelial regulation of hemostasis is complex and involves a delicate interplay of structural components and feedback mechanisms. Thus, challenges to develop new strategies for blood-compatible biomaterials now lie in incorporating true feedback controlled mechanisms that can regulate blood compatibility in a dynamic way. Here, supramolecular material systems are highlighted as they provide a promising platform to introduce dynamic reciprocity, due to their inherent dynamic nature.

Highly Specific Binding on Antifouling Zwitterionic Polymer-Coated Microbeads as Measured by Flow Cytometry

Micron- and nano-sized particles are extensively used in various biomedical applications. However, their performance is often drastically hampered by the nonspecific adsorption of biomolecules, a process called biofouling, which can cause false-positive and false-negative outcomes in diagnostic tests. Although antifouling coatings have been extensively studied on flat surfaces, their use on micro- and nanoparticles remains largely unexplored, despite the widespread experimental (specifically, clinical) uncertainties that arise because of biofouling. Here, we describe the preparation of magnetic micron-sized beads coated with zwitterionic sulfobetaine polymer brushes that display strong antifouling characteristics. These coated beads can then be equipped with recognition elements of choice, to enable the specific binding of target molecules. First, we present a proof of principle with biotin-functionalized beads that are able to specifically bind fluorescently labeled streptavidin from a complex mixture of serum proteins. Moreover, we show the versatility of the method by demonstrating that it is also possible to functionalize the beads with mannose moieties to specifically bind the carbohydrate-binding protein concanavalin A. Flow cytometry was used to show that thus-modified beads only bind specifically targeted proteins, with minimal/near-zero nonspecific protein adsorption from other proteins that are present. These antifouling zwitterionic polymer-coated beads, therefore, provide a significant advancement for the many bead-based diagnostic and other biosensing applications that require stringent antifouling conditions.

Covalent Surface Modification of Silicon Oxides with Alcohols in Polar Aprotic Solvents

Alcohol-based monolayers were successfully formed on the surfaces of silicon oxides through reactions performed in polar aprotic solvents. Monolayers prepared from alcohol-based reagents have been previously introduced as an alternative approach to covalently modify the surfaces of silicon oxides. These reagents are readily available, widely distributed, and are minimally susceptible to side reactions with ambient moisture. A limitation of using alcohol-based compounds is that previous reactions required relatively high temperatures in neat solutions, which can degrade some alcohol compounds or could lead to other unwanted side reactions during the formation of the monolayers. To overcome these challenges, we investigate the condensation reaction of alcohols on silicon oxides carried out in polar aprotic solvents. In particular, propylene carbonate has been identified as a polar aprotic solvent that is relatively nontoxic, readily accessible, and can facilitate the formation of alcohol-based monolayers. We have successfully demonstrated this approach for tuning the surface chemistry of silicon oxide surfaces with a variety of alcohol containing compounds. The strategy introduced in this research can be utilized to create silicon oxide surfaces with hydrophobic, oleophobic, or charged functionalities.

Facile Preparation of Crosslinked PAN Membranes Based on Thiol-Ene Photopolymerization

To improve the mechanical strength and antipollution properties of membranes, this research presents a facile method to prepare crosslinked polyacrylonitrile (PAN) membranes. This was achieved firstly by radical copolymerization with acrylonitrile, allyl methacrylate and sulfobetaine methacrylamide. Then, the copolymer was crosslinked by a thiol-ene click reaction under UV irradiation. Finally, the crosslinked membranes were prepared by traditional immersion precipitation phase inversion. These prepared membranes showed excellent water-pressure resistance and solvent swelling, owing to their crosslinked structure. This research will help in preparing crosslinked membranes through facile crosslinking under mild reaction conditions. The betaine structure also considerably improved the antifouling properties of the membranes.

Self-Propulsion and Shape Restoration of Aqueous Drops on Sulfobetaine Silane Surfaces

The motion of droplets on typical surfaces is generally halted by contact line pinning associated with contact angle hysteresis. In this study, it was shown that, on a zwitterionic sulfobetaine silane (SBSi)-coated surface, aqueous drops with appropriate solutes can demonstrate hysteresis-free behavior, whereas a pure water drop shows spontaneous spreading. By adding solutes such as polyethylene glycol, 2(2-butoxy ethoxy) ethanol, or sodium n-dodecyl sulfate, an aqueous drop with a small contact angle (disappearance of spontaneous spreading) was formed on SBSi surfaces. The initial drop shape was readily relaxed back to a circular shape (hysteresis-free behavior), even upon severe disturbances. Moreover, it was interesting to observe the self-propulsion of such a drop on horizontal SBSi surfaces in the absence of externally provided stimuli. The self-propelled drop tends to follow a random trajectory, and the continuous movement can last for at least 10 min. This self-propelled random motion can be attributed to the combined effects of the hysteresis-free surface and the Marangoni stress. The former comes from the total wetting property of the surface, while the latter originates from surface tension gradient due to fluctuating evaporation rates along the drop border.

Mild and Selective C-H Activation of COC Microfluidic Channels Allowing Covalent Multifunctional Coatings

Plastics, such as cyclic olefin copolymer (COC), are becoming an increasingly popular material for microfluidics. COC is used, in part, because of its (bio)-chemical resistance. However, its inertness and hydrophobicity can be a major downside for many bioapplications. In this paper, we show the first example of a surface-bound selective C-H activation of COC into alcohol C-OH moieties under mild aqueous conditions at room temperature. The nucleophilic COC-OH surface allows for subsequent covalent attachments, such as of a H-terminated silane. The resulting hybrid material (COC-Si-H) was then modified via a photolithographic hydrosilylation in the presence of ω-functionalized 1-alkenes to form a new highly stable, solvent-resistant hybrid surface.

Preparation, characterization, and protein-resistance of films derived from a series of α-oligo(ethylene glycol)-ω-alkenes on H–Si(111) surfaces

Films on Si(111) were prepared by photo-activated grafting of CH₂&#xe001;CH(CH₂)m(OCH₂CH₂)nOCH₃ (m = 8, 9; n = 3–7) by using different vacuum conditions. High vacuum produced a higher thickness (40 Å) and <0.8% fibrinogen adsorption (C₁₀EG₇). Films were stable even after 28 days.

Water-repairable zwitterionic polymer coatings for anti-biofouling surfaces

We developed a strategy to prepare new types of zwitterionic polymer network (ZPN) coatings that display excellent self-healing and anti-biofouling properties.