Electrical Double-Layer and Ion Bridging Forces between Symmetric and Asymmetric Charged Surfaces in the Presence of Mono- and Divalent Ions

Self-association and gel formation during sedimentation of like-charged colloids

Formation of superstructures from colloidal dispersion involves a continuous increase in particle concentration, resulting in increasingly more complicated interparticle interaction. At high particle concentration, the presence of the super-crowding effect, strong non-ideality in addition to significant light absorption and scattering makes particle analysis very difficult. Here we report quantitative molecular, microscopic and macroscopic experimental results on like-charged colloids with concentration up to 60 vol%, close to the densest possible packing of spheres. It is achieved by conducting sedimentation-diffusion-equilibrium analytical ultracentrifugation (SE-AUC) on a concentrated dispersion of colloidal silica nanoparticles in a refractive-index-matching solvent. Surprisingly, we observed the self-association and even colloidal gel formation of like-charged colloids at very high concentration. Further experiments indicate that the attraction force may be counter-ion mediated. These results represent an important step forward in understanding complicated interparticle interaction in extremely high concentration, which is vital for the controlled fabrication of colloidal superstructures.

Recovery of iron from iron-rich pickling sludge for preparing P-doped polyferric chloride coagulant

The pickling sludge produced from rolling process contains a large amount of Fe, Ca, Al as well as other metals. If these metals can be extracted and used, it will promote the recycling of pickling sludge. Herein, we proposed a two-step extraction method to extract Fe ions out from the pickling sludge, and then the extracted Fe was oxidized by H₂O₂ and prepared into Fe-containing coagulant in the presence of Na₂HPO₄ as stabilizer. The three main factors that affect the color removal efficiency and COD removal efficiency are identified as P:Fe ratio, H₂O₂ adding amount, and curing time. Results show that the optimal preparation conditions are: P:Fe = 0.05, H₂O₂ amount = 115%, and the curing time = 6 d, at which the color and COD removal efficiency reached 96.25% and 65.91%, respectively. The assessment of toxicity of the PPFC indicated that the content of harmful substances meets the thresholds in Chinese national standard GB141591-2016. The findings in this study are expected to provide new implications in treating different kinds of Fe-containing sludge.

Effect of Divalent Cations on the Interaction of Carboxylate Self-Assembled Monolayers

Interactions between organic molecules in aqueous environments, whether in the fluid phase or adsorbed on solids, are often affected by the cations present in the solution. We investigated, at nanometer scale, how surface carboxylate interactions are influenced by dissolved divalent cations: Mg²⁺, Ca²⁺, Sr²⁺, and Ba²⁺. Self-assembled monolayer (SAM) surfaces with exposed terminations of alkyl, -CH₃, carboxylate, -COO^- , or dicarboxylate, -DiCOO^-, were deposited on gold-coated tips and substrates. We used atomic force microscopy (AFM), in chemical force mapping (CFM) mode, to measure adhesion forces between various combinations of SAMs on the tip and substrate, in solutions of 0.5 M NaCl, that contained 0.012 M of one of the divalent cations. The type of cation, the number of carboxyl groups that interact, and their structure on the SAM influenced adhesion between the surfaces. The effect of the reference solution, which only contains Na⁺ cations, on adhesion force was mainly attributed to van der Waals and hydrophobic forces, explaining the lower force in systems that are more hydrophilic, i.e., -COO^--COO^-, and higher force for more hydrophobic systems. For charged surfaces, i.e., -COO^- and -DiCOO^-, in divalent cation solutions results were consistent with ion bridging. The inclusion of a hydrophobic surface, i.e., the -CH₃-COO^- or -CH₃-DiCOO^- system, decreased the possibility for strong cation bridging with the charged surface, resulting in lower adhesion. For systems including -COO^-, the adhesion force series followed the inverse cation hydrated radius trend (Na⁺ ≈ Mg²⁺ < Sr²⁺ < Ca²⁺ < Ba²⁺) whereas -DiCOO^- was responsible for lower adhesion force and modified trends, depending on the corresponding surface in the system. Differences in force magnitude between the monolayers were correlated with lower charge availability on the -DiCOO^- surface as a result of fewer active sites, probably because of the tendency of exposed malonate surface groups to interact between them, as well as high rigidity, resulting from the molecule structure. The characteristic response of the -DiCOO^- surface in solutions of Sr²⁺ and Ca²⁺ was correlated with possible malonate complexation modes. Comparison with previous studies suggested that the strong response of a -DiCOO^- surface to Sr²⁺ resulted from bidentate chelation, whereas Ca²⁺ response was attributed to alpha-mode association to malonate.

Understanding the surface properties and rheology of a silica suspension mediated by a comb-type poly(acrylic acid)/poly(ethylene oxide) (PAA/PEO) copolymer: effect of salinity

Understanding the surface properties and rheology of colloidal suspensions in the presence of polymer additives with high salinity are of great importance in formulating construction materials and optimizing process conditions in the mining and petroleum industry. In this work, the surface properties and rheology of a model spherical silica aqueous suspension mediated by a comb-type poly(acrylic acid)/poly(ethylene oxide) (PAA/PEO) copolymer at various salt concentrations have been investigated. Adsorption measurements using a Quartz Crystal Microbalance with Dissipation monitoring (QCM-D) align well with zeta potential tests and show that polymer adsorption on silica surfaces is enhanced at high salinity (i.e., 3 M NaCl) than at low salinity (i.e., 1 mM NaCl) due to the suppression of the electrical double layer. Surface Forces Apparatus (SFA) measurements reveal that for interactions between two mica surfaces (the basal plane of which has a similar structure as silica) at a high polymer concentration (e.g., 2 wt%), steric repulsion dominates in 1 mM NaCl while bridging attraction is observed in 3 M NaCl. Surface force measurements agree with rheological results on silica suspensions with 0.5 to 2 wt% of PAA/PEO addition, which shows a significant decrease in yield stress in 1 mM NaCl due to steric repulsion but an insignificant variation in yield stress in 3 M NaCl due to attractive bridging interactions. This work provides useful information regarding the surface properties and rheological properties of comb-type polymer-mediated silica suspensions under different salinity conditions, with implications on designing and processing complex colloidal suspensions with polymer additives for various applications.

Control of interface interactions between natural rubber and solid surfaces through charge effects: an AFM study in force spectroscopic mode

Adhesion of nanoparticles (natural rubber) is monitored by slight changes in the surface charge state of the contacting solid surfaces.