Two Nanoporous Crystalline Forms of Poly(2,6-dimethyl-1,4-phenylene)oxide and Related Co-Crystalline Forms

Raman Analysis of Orientation and Crystallinity in High Tg, Low Crystallinity Electrospun Fibers

Electrospun fibers of amorphous or low-crystallinity polymers typically exhibit a low molecular orientation that can hamper their properties and application. A key stage of the electrospinning process that could be harnessed to mitigate the loss of orientation is jet rigidification, which relates closely to the solvent evaporation rate. Here, we establish quantitative Raman methods to assess the molecular orientation and crystallinity of weakly crystalline poly(2,6-dimethyl-1,4-phenylene oxide) fibers with varying diameters. Our findings demonstrate that solvent volatility can be leveraged to modulate the orientation and crystallinity through its impact on the effective glass transition temperature (Tg,eff) of the polymer jet during the electrospinning process. Specifically, a highly volatile solvent yields a higher and more sustained orientation (median ⟨P2⟩ of 0.53 for diameters < 1.0 µm) because its fast evaporation rapidly increases Tg,eff above room temperature. This vitrification early along the jet path promotes the formation of an oriented amorphous phase and a moderate fraction of strain-induced crystals. Our data reveals that a high Tg is a crucial parameter for reaching high orientation in amorphous or low-crystallinity polymer systems.

Hydrogen Bonded Dimer of an Alcohol with the Derived Carboxylic Acid Triggering their Sorption by Nanoporous-crystalline PPO Films

Films exhibiting nanoporous-crystalline (NC) phases of poly(2,6-dimethyl-1,4-phenylene) oxide (PPO), which are highly effective to absorb apolar organic guest molecules, are also able to absorb polar molecules (like alcohols and carboxylic acids) but only from concentrated organic solutions. NC PPO films, which do not absorb alcohols and carboxylic acids from diluted aqueous solutions, exhibits a huge uptake (even above 30 wt %) of benzyl alcohol (BAL) and benzoic acid (BA), if BA is obtained by spontaneous room temperature oxidation of BAL in aqueous solution. This phenomenon is rationalized by an easy uptake, mainly by the PPO intrahelical crystalline empty channels, of a BAL/BA 1/1 hydrogen-bonded dimer. This huge uptake of BAL/BA dimer by NC PPO films, which is also fast for films exhibiting the orientation of the crystalline helices perpendicular to the film plane (c⊥ orientation), can be exploited for purification of water from BAL, when present in traces. High and fast sorption of a hydrogen bonded dimer and negligible sorption of the two separate compounds is possibly unprecedented for absorbent materials.

Salicylic Acid Release from Syndiotactic Polystyrene Staple Fibers

Films and fibers of syndiotactic polystyrene (sPS), being amorphous or exhibiting nanoporous crystalline (NC) or dense crystalline phases, were loaded with salicylic acid (SA), a relevant non-volatile antimicrobial molecule. In the first section of the paper, sPS/SA co-crystalline (CC) δ form is characterized, mainly by wide angle X-ray diffraction (WAXD) patterns and polarized Fourier transform infrared (FTIR) spectra. The formation of sPS/SA δ CC phases allows the preparation of sPS fibers even with a high content of the antibacterial guest, which is also retained after repeated washing procedures at 65 °C. A preparation procedure starting from amorphous fibers is particularly appropriate because involves a direct formation of the CC δ form and a simultaneous axial orientation. The possibility of tuning drug amount and release kinetics, by simply selecting suitable crystalline phases of a commercially available polymer, makes sPS fibers possibly useful for many applications. In particular, fibers with δ CC forms, which retain SA molecules in their crystalline phases, could be useful for antimicrobial textiles and fabrics. Fibers with the dense γ form which easily release SA molecules, because they are only included in their amorphous phases, could be used for promising SA-based preparations for antibacterial purposes in food processing and preservation and public health. Finally, using a cell-based assay system and antibacterial tests, we investigated the cellular activity, toxicity and antimicrobial properties of amorphous, δ CC forms and dense γ form of sPS fibers loaded with different contents of SA.

Segregation of Benzoic Acid in Polymer Crystalline Cavities

Benzoic acid (BA) and its derivatives are very attractive because of their pharmacological properties, such as antioxidant, radical-regulating, antiviral, antitumor, anti-inflammatory, antimicrobial and antifungal. Syndiotactic polystyrene (sPS) and poly(2,6-dimethyl-1,4-phenylene)oxide (PPO) films exhibiting co-crystalline phases with BA were prepared and characterized by WAXD, FTIR and polarized FTIR measurements. The FTIR measurements clearly showed that BA was present mainly as a dimer in the crystalline channels of the ε form of sPS as well as in the α form of PPO, as generally occurs not only in the solid state but also in organic dilute solutions. BA was instead present as isolated molecules in the crystalline cavities of the δ form of sPS. In fact, the FTIR spectra of BA guest molecules exhibited vibrational peaks close to those of BA in its vapor phase. Hence, the nanoporous-crystalline δ form of sPS not only avoids additive aggregation but also leads to the separation of dimeric molecules and the segregation of monomeric BA.

Novel PDMS-b-PPO Membranes Modified with Graphene Oxide for Efficient Pervaporation Ethanol Dehydration

Purification and concentration of bioalcohols is gaining new status due to their use as a promising alternative liquid biofuel. In this work, novel high-performance asymmetric membranes based on a block copolymer (BCP) synthesized from polydimethylsiloxane (PDMS) and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) were developed for enhanced pervaporation dehydration of ethanol. Improvement in dehydration performance was achieved by obtaining BCP membranes with a "non-perforated" porous structure and through surface and bulk modifications with graphene oxide (GO). Formation of the BCP was confirmed by Fourier-transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopies. The changes to morphology and physicochemical properties of the developed BCP and BCP/GO membranes were studied by scanning electron (SEM) and atomic force (AFM) microscopies, thermogravimetric analysis (TGA) and contact angle measurements. Transport properties of the developed membranes were evaluated by the pervaporation dehydration of ethanol over a wide concentration range (4.4-70 wt.% water) at 22 °C. The BCP (PDMS:PPO:2,4-diisocyanatotoluene = 41:58:1 wt.% composition) membrane modified with 0.7 wt.% GO demonstrated optimal transport characteristics: 80-90 g/(m²h) permeation flux with high selectivity (76.8-98.8 wt.% water in the permeate, separation factor of 72-34) and pervaporation separation index (PSI) of 5.5-2.9.

Basified Graphene Oxide and PPO Composite Aerogel with Basified Graphene Oxide for Henry Reaction in Solvent-Free Conditions: A Green Approach

Novel basified graphene oxide and high-porosity monolithic composite aerogels of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) containing basified graphene oxide (b-eGO) have been prepared as recoverable and reusable catalysts for the Henry reaction in solvent-free conditions at room temperature. The results showed that, although b-eGO was able to promote the reaction, it suffered from reduced stability. On the other hand, PPO/b-eGO aerogels were able to efficiently promote the Henry reaction in solvent-free conditions. The product could be obtained pure without a purification step, and the catalyst was stable for over 15 months and could be easily recycled without losing catalytic efficiency. The stereochemical outcome was further investigated in the presence of PPO/b-eGO. Despite its negligible influence on diastereoselectivity, better efficiency and a sensible reduction of reaction time were observed.

Nanoporous–Crystalline Poly(2,6-dimethyl-1,4-phenylene)oxide Aerogels with Selectively Sulfonated Amorphous Phase for Fast VOC Sorption from Water

This paper describes the preparation and characterization of poly(2,6-dimethyl-1,4-phenylene)oxide (PPO) highly porous monolithic aerogels with a hydrophobic nanoporous–crystalline phase and a hydrophilic sulfonated amorphous phase. The sulfonated aerogels were obtained by the sulfonation of PPO physical gels, followed by the supercritical CO₂ extraction of solvents. WAXD and FTIR analysis showed that the nanoporous–crystalline phase was preserved for a degree of sulfonation up to c.a. 35%, allowing a highly volatile organic compound (VOC) sorption capacity. The sulfonated PPO aerogels exhibited a high water sorption capacity, with a water uptake of up to 500 wt%, and faster VOC sorption kinetics from water with respect to unsulfonated aerogels.

Novel Mixed Matrix Membranes Based on Polyphenylene Oxide Modified with Graphene Oxide for Enhanced Pervaporation Dehydration of Ethylene Glycol

Ethylene glycol (EG) is widely used in various economic and industrial fields. The demand for its efficient separation and recovery from water is constantly growing. To improve the pervaporation characteristics of a poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) membrane in dehydration of ethylene glycol, the modification with graphene oxide (GO) nanoparticles was used. The effects of the introduction of various GO quantities into the PPO matrix on the structure and physicochemical properties were studied by Fourier-transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopies, scanning electron (SEM) and atomic force (AFM) microscopies, thermogravimetric analysis (TGA), swelling experiments, and contact angle measurements. Two types of membranes based on PPO and PPO/GO composite were developed: dense membranes and supported membranes on a fluoroplast substrate (MFFC). Transport properties of the developed membranes were evaluated in the pervaporation dehydration of EG in a wide concentration range (10–90 wt.% and 10–30 wt.% water for the dense and supported membranes, respectively). The supported PPO/GO(0.7%)/MFFC membrane demonstrated the best transport properties in pervaporation dehydration of EG (10–30 wt.% water) at 22 °C: permeation flux ca. 15 times higher compared to dense PPO membrane—180–230 g/(m²·h)), 99.8–99.6 wt.% water in the permeate. The membrane is suitable for the promising industrial application.

Molecular Features Behind Formation of α or β Co-Crystalline and Nanoporous-Crystalline Phases of PPO

Guest molecular features determining the formation of α and β phases of poly(2-6-dimethyl-1,4-phenylene) oxide (PPO) are explored by collecting literature data and adding many new film preparations, both by solution casting and by guest sorption in amorphous films. Independently of the considered preparation method, the α-form is favored by the hydrophobic and bulky guest molecules, while the hydrophilic and small guest molecules favor the β-form. Furthermore, molecular modeling studies indicate that the β-form inducer guests establish stronger dispersive interactions with the PPO units than the α-form inducer guests. Thus, the achievement of co-crystalline (and derived nanoporous crystalline) α- and β-forms would result from differences in energy gain due to the host-guest interactions established at the local scale.

Features of the Gas-Permeable Crystalline Phase of Poly-2,6-dimethylphenylene Oxide

Poly-2,6-dimethylphenylene oxide (PPO) film samples with varying degrees of crystallinity (from 0 to 69%) were obtained by means of different techniques. The films were studied by various physicochemical methods (Fourier-transform infrared spectroscopy, positron annihilation lifetime spectroscopy, X-ray diffraction, and ¹H nuclear magnetic resonance relaxation). Solubility coefficients of gases in the PPO samples were measured via sorption isotherms of gases by volumetric technique with chromatographic detection. The apparent activation energy of permeation and the activation energy of diffusion of all gases were estimated based on temperature dependences of gas permeability and diffusivity for amorphous and semi-crystalline PPO in the range of 20–50 °C. The peculiarities of free volume, density, and thermal properties of gas transport confirm the nanoporosity of the gas-permeable crystalline phase of PPO. So, the PPO can be included in the group of organic molecular sieves.

Dependence on Film Thickness of Guest-Induced c Perpendicular Orientation in PPO Films

For poly(2,6-dimethyl-1,4-phenylene)oxide (PPO) films exhibiting nanoporous-crystalline (NC) phases, c⟂ orientation (i.e., crystalline polymer chain axes being preferentially perpendicular to the film plane) is obtained by crystallization of amorphous films, as induced by sorption of suitable low-molecular-mass guest molecules. The occurrence of c⟂ orientation is relevant for applications of NC PPO films because it markedly increases film transparency as well as guest diffusivity. Surprisingly, we show that the known crystallization procedures lead to c⟂ oriented thick (50-300 μm) films and to unoriented thin (≤20 μm) films. This absence of crystalline phase orientation for thin films is rationalized by fast guest sorption kinetics, which avoid co-crystallization in confined spaces and hence inhibit formation of flat-on lamellae. For thick films exhibiting c⟂ orientation, sigmoid kinetics of guest sorption and of thickening of PPO films are observed, with inflection points associated with guest-induced film plasticization. Corresponding crystallization kinetics are linear with time and show that co-crystal growth is poorly affected by film plasticization. An additional relevant result of this study is the linear relationship between WAXD crystallinity index and DSC melting enthalpy, which allows evaluation of melting enthalpy of the NC α form of PPO (ΔHmο = 42 ± 2 J/g).

Monomeric and Dimeric Carboxylic Acid in Crystalline Cavities and Channels of Delta and Epsilon Forms of Syndiotactic Polystyrene

Delta (δ) and epsilon (ε) co-crystalline forms of syndiotactic polystyrene with a carboxylic acid guest were obtained by sorption of liquid hexanoic acid in syndiotactic polystyrene films exhibiting delta and epsilon nanoporous-crystalline forms. The characterization study is facilitated by axially stretched syndiotactic polystyrene films, used both for polarized FTIR spectra and for WAXD fiber patterns. Particularly informative are two carbonyl-stretching FTIR peaks, attributed to monomeric and dimeric hexanoic acid. The dichroism of these carbonyl peaks indicates that both delta and epsilon phases are able to include hexanoic acid as isolated guest molecules, while only the epsilon phase is also able to include dimeric hexanoic acid molecules in its crystalline channels. The inclusion of both isolated and dimeric hexanoic acid species in the epsilon form crystalline channels produces extremely fast hexanoic acid uptakes by syndiotactic polystyrene epsilon form films.

Absorption and Isomerization of Azobenzene Guest Molecules in Polymeric Nanoporous Crystalline Phases

PPO co-crystalline (CC) films including azobenzene guest molecules have been prepared and characterized by WAXD, FTIR and UV-Visible measurements. Isomerization reactions of azobenzene (photo-induced trans to cis and spontaneous cis to trans) included in α and β nanoporous-crystalline (NC) phases leading to CC phases, or simply absorbed in amorphous phase have been studied on thick and thin films. Spectroscopic analysis shows that photo-isomerization of azobenzene occurs without expulsion of azobenzene guest molecules from crystalline phases. Sorption studies of α and β NC films immersed into photo-isomerized azobenzene solution reveal a higher selectivity of the β NC phase toward cis azobenzene isomer than the α NC phase, inducing us to propose the β NC phase as particularly suitable for absorbing spherically bulky guest molecules.

Nanoporous Crystalline Composite Aerogels with Reduced Graphene Oxide

High-porosity monolithic composite aerogels of syndiotactic polystyrene (sPS) and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) containing reduced graphene oxide (r-GO) were prepared and characterized. The composite aerogels obtained by supercritical carbon dioxide (scCO₂) extraction of sPS/r-GO and PPO/r-GO gels were characterized by a fibrillar morphology, which ensured good handling properties. The polymer nanoporous crystalline phases obtained within the aerogels led to high surface areas with values up to 440 m² g⁻¹. The role of r-GO in aerogels was studied in terms of catalytic activity by exploring the oxidation capacity of composite PPO and sPS aerogels toward benzyl alcohol in diluted aqueous solutions. The results showed that, unlike sPS/r-GO aerogels, PPO/r-GO aerogels were capable of absorbing benzyl alcohol from the diluted solutions, and that oxidation of c.a. 50% of the sorbed benzyl alcohol molecules into benzoic acid occurred.

Axial Orientation of Co-Crystalline Phases of Poly(2,6-Dimethyl-1,4-Phenylene)Oxide Films

Films exhibiting co-crystalline (CC) phases between a polymer host and low-molecular-mass guest molecules are relevant for many applications. As is usual for semi-crystalline polymers, axially oriented films can give relevant information on the crystalline structure, both by Wide Angle X-ray diffraction fiber patterns and by polarized Fourier-transform infrared spectroscopy. Axially oriented CC phases of poly(2,6-dimethyl-1,4-phenylene)oxide (PPO) with 1,3,5-trimethylbenzene (mesitylene) can be simply obtained by the stretching of CC PPO films. In fact, due to the plasticization effect of this highly boiling guest, PPO orientation can occur in a stretching temperature range (170-175 °C) nearly 50 °C lower than that generally needed for PPO films (220-230 °C). This low stretching temperature range allows avoidance of polymer oxidation, as well as formation of the mesomorphic dense γ PPO phase. Axially oriented CC phases of PPO with toluene, i.e., with a more volatile guest, can be instead obtained by the stretching (in the same low temperature range: 170-175 °C) of CC PPO blend films with polystyrene.