Efficiency Roll-Off Free Electroluminescence from Monolayer WSe2

Room-temperature efficient and tunable interlayer exciton emissions in WS2/WSe2 heterobilayers at high generation rates

Transition metal dichalcogenide (TMDC) heterobilayers (HBs) have been intensively investigated lately because they offer novel platforms for the exploration of interlayer excitons (IXs). However, the potentials of IXs in TMDC HBs have not been fully studied as efficient and tunable emitters for both photoluminescence (PL) and electroluminescence (EL) at room temperature (RT). Also, the efficiencies of the PL and EL of IXs have not been carefully quantified. In this work, we demonstrate that IX in WS2/WSe2 HBs could serve as promising emitters at high generation rates due to its immunity to efficiency roll-off. Furthermore, by applying gate voltages to balance the electron and hole concentrations and to reinforce the built-in electric fields, high PL quantum yield (QY) and EL external quantum efficiency (EQE) of ∼0.48% and ∼0.11% were achieved at RT, respectively, with generation rates exceeding 1021 cm-2·s-1, which confirms the capabilities of IXs as efficient NIR light emitters by surpassing most of the intralayer emissions from TMDCs.

Composition Modulation-Mediated Band Alignment Engineering from Type I to Type III in 2D vdW Heterostructures

Band alignment engineering is crucial for facilitating charge separation and transfer in optoelectronic devices, which ultimately dictates the behavior of Van der Waals heterostructures (vdWH)-based photodetectors and light emitting diode (LEDs). However, the impact of the band offset in vdWHs on important figures of merit in optoelectronic devices has not yet been systematically analyzed. Herein, the regulation of band alignment in WSe2/Bi2Te3- xSex vdWHs (0 ≤ x ≤ 3) is demonstrated through the implementation of chemical vapor deposition (CVD). A combination of experimental and theoretical results proved that the synthesized vdWHs can be gradually tuned from Type I (WSe2/Bi2Te3) to Type III (WSe2/Bi2Se3). As the band alignment changes from Type I to Type III, a remarkable responsivity of 58.12 A W-1 and detectivity of 2.91×1012 Jones (in Type I) decrease in the vdWHs-based photodetector, and the ultrafast photoresponse time is 3.2 µs (in Type III). Additionally, Type III vdWH-based LEDs exhibit the highest luminance and electroluminescence (EL) external quantum efficiencies (EQE) among p-n diodes based on Transition Metal Dichalcogenides (TMDs) at room temperature, which is attributed to band alignment-induced distinct interfacial charge injection. This work serves as a valuable reference for the application and expansion of fundamental band alignment principles in the design and fabrication of future optoelectronic devices.

Gate Controlled Excitonic Emission in Quantum Dot Thin Films

Formation of charged trions is detrimental to the luminescence quantum efficiency of colloidal quantum dot (QD) thin films as they predominantly undergo nonradiative recombination. In this regard, control of charged trion formation is of interest for both fundamental characterization of the quasi-particles and performance optimization. Using CdSe/CdS QDs as a prototypical material system, here we demonstrate a metal-oxide-semiconductor capacitor based on QD thin films for studying the background charge effect on the luminescence efficiency and lifetime. The concentration ratio of the charged and neutral quasiparticles in the QDs is reversibly controlled by applying a gate voltage, while simultaneous steady-state and time-resolved photoluminescence measurements are performed. Notably, the photoluminescence intensity is modulated by up to 2 orders of magnitude with a corresponding change in the effective lifetime. In addition, chip-scale modulation of brightness is demonstrated, where the photoluminescence is effectively turned on and off by the gate, highlighting potential applications in voltage-controlled electrochromics.

Built-in tensile strain dependence on the lateral size of monolayer MoS2 synthesized by liquid precursor chemical vapor deposition

Strain engineering is an efficient tool to tune and tailor the electrical and optical properties of 2D materials. The built-in strain can be tuned during the synthesis process of a two-dimensional semiconductor, such as molybdenum disulfide, by employing different growth substrates with peculiar thermal properties. In this work, we demonstrate that the built-in strain of MoS2 monolayers, grown on a SiO2/Si substrate by liquid precursor chemical vapor deposition, is mainly dependent on the size of the monolayer. In fact, we identify a critical size equal to 20 μm, from which the built-in strain increases drastically. The built-in strain is the maximum for a 60 μm sized monolayer, leading to 1.2% tensile strain with a partial release of strain close to the monolayer triangular vertexes due to the formation of nanocracks. These findings also imply that the standard method for evaluation of the number of layers based on the Raman mode separation can become unreliable for highly strained monolayers with a lateral size above 20 μm.

Electroluminescence from Megasonically Solution-Processed MoS2 Nanosheet Films

Due to their superior optoelectronic properties, monolayer two-dimensional (2D) transition metal dichalcogenides (TMDs) have attracted significant attention for electroluminescent devices. However, challenges in isolating optoelectronically active TMD monolayers using scalable liquid phase exfoliation have precluded electroluminescence in large-area, solution-processed TMD films. Here, we overcome these limitations and demonstrate electroluminescence from molybdenum disulfide (MoS2) nanosheet films by employing a monolayer-rich MoS2 ink produced by electrochemical intercalation and megasonic exfoliation. Characteristic monolayer MoS2 photoluminescence and electroluminescence spectral peaks at 1.88-1.90 eV are observed in megasonicated MoS2 films, with the emission intensity increasing with film thickness over the range 10-70 nm. Furthermore, employing a vertical light-emitting capacitor architecture enables uniform electroluminescence in large-area devices. These results indicate that megasonically exfoliated MoS2 monolayers retain their direct bandgap character in electrically percolating thin films even following multistep solution processing. Overall, this work establishes megasonicated MoS2 inks as an additive manufacturing platform for flexible, patterned, and miniaturized light sources that can likely be expanded to other TMD semiconductors.

Silver nanoparticle-induced enhancement of light extraction in two-dimensional light-emitting diodes

Monolayer transition metal dichalcogenides (TMDCs) with direct bandgaps are considered promising candidates for building light-emitting diodes (LEDs). One crucial indicator of their performance is the brightness of electroluminescence (EL). In this study, we fabricate WS2-based LEDs that make full use of the assistance of effective transient-mode charge injection. By introducing self-assembled silver nanoparticles (NPs) on top of the LED, the extraction efficiency is significantly improved, with a 2.9-fold EL enhancement observed in the experiment. Full-wave simulations further confirm that the improvement comes from the scattering capability of silver NPs, with results qualitatively fitting the experiment. This approach, with its compatibility with van der Waals heterostructures, can be further promoted to enhance the brightness of 2D monolayer TMDC-based LEDs.

Dielectrics for Two-Dimensional Transition-Metal Dichalcogenide Applications

Despite over a decade of intense research efforts, the full potential of two-dimensional transition-metal dichalcogenides continues to be limited by major challenges. The lack of compatible and scalable dielectric materials and integration techniques restrict device performances and their commercial applications. Conventional dielectric integration techniques for bulk semiconductors are difficult to adapt for atomically thin two-dimensional materials. This review provides a brief introduction into various common and emerging dielectric synthesis and integration techniques and discusses their applicability for 2D transition metal dichalcogenides. Dielectric integration for various applications is reviewed in subsequent sections including nanoelectronics, optoelectronics, flexible electronics, valleytronics, biosensing, quantum information processing, and quantum sensing. For each application, we introduce basic device working principles, discuss the specific dielectric requirements, review current progress, present key challenges, and offer insights into future prospects and opportunities.

Anomalous thickness dependence of photoluminescence quantum yield in black phosphorous

Black phosphorus has emerged as a unique optoelectronic material, exhibiting tunable and high device performance from mid-infrared to visible wavelengths. Understanding the photophysics of this system is of interest to further advance device technologies based on it. Here we report the thickness dependence of the photoluminescence quantum yield at room temperature in black phosphorus while measuring the various radiative and non-radiative recombination rates. As the thickness decreases from bulk to ~4 nm, a drop in the photoluminescence quantum yield is initially observed due to enhanced surface carrier recombination, followed by an unexpectedly sharp increase in photoluminescence quantum yield with further thickness scaling, with an average value of ~30% for monolayers. This trend arises from the free-carrier to excitonic transition in black phosphorus thin films, and differs from the behaviour of conventional semiconductors, where photoluminescence quantum yield monotonically deteriorates with decreasing thickness. Furthermore, we find that the surface carrier recombination velocity of black phosphorus is two orders of magnitude lower than the lowest value reported in the literature for any semiconductor with or without passivation; this is due to the presence of self-terminated surface bonds in black phosphorus.