On the Mechanism of Hydrophilicity of Graphene

Water as Solvent for the Dispersion of 2D Nanostructured Materials

The development of large number of two-dimensional (2D) nanostructured materials that followed the success of graphene and the need for their handling and manipulation e. g., in inks, brought to the fore the study of solvents and substances that contribute to the stabilization of 2D nanomaterials in the liquid phase. The successful dispersion of 2D materials in solvents is combined with one of the most widespread preparation methods, that of liquid phase exfoliation. In this article, a review for the role of water in the preparation of different 2D nanostructures and their stable dispersions in the liquid phase is discussed. The use of water as a solvent or dispersant is instrumental in promoting materials with an ecological footprint, low cost, and sustainability.

Humidity Sensing Properties of Different Atomic Layers of Graphene on the SiO2/Si Substrate

Graphene has great potential to be used for humidity sensing due to its ultrahigh surface area and conductivity. However, the impact of different atomic layers of graphene on the SiO2/Si substrate on humidity sensing has not been studied yet. In this paper, we fabricated three types of humidity sensors on the SiO2/Si substrate based on one to three atomic layers of graphene, in which the sensing areas of graphene are 75 μm × 72 μm and 45 μm × 72 μm, respectively. We studied the impact of both the number of atomic layers of graphene and the sensing areas of graphene on the responsivity and response/recovery time of the prepared graphene-based humidity sensors. We found that the relative resistance change of the prepared devices decreased with the increase of number of atomic layers of graphene under the same change of relative humidity. Further, devices based on tri-layer graphene showed the fastest response/recovery time, while devices based on double-layer graphene showed the slowest response/recovery time. Finally, we chose devices based on double-layer graphene that have relatively good responsivity and stability for application in respiration monitoring and contact-free finger monitoring.

Efficient Ionovoltaic Energy Harvesting via Water-Induced p-n Junction in Reduced Graphene Oxide

Water motion-induced energy harvesting has emerged as a prominent means of facilitating renewable electricity from the interaction between nanostructured materials and water over the past decade. Despite the growing interest, comprehension of the intricate solid-liquid interfacial phenomena related to solid state physics remains elusive and serves as a hindrance to enhancing energy harvesting efficiency up to the practical level. Herein, the study introduces the energy harvester by utilizing inversion on the majority charge carrier in graphene materials upon interaction with water molecules. Specifically, various metal electrode configurations are employed on reduced graphene oxide (rGO) to unravel its distinctive charge carriers that experience the inversion in semiconductor type upon water contact, and exploit this characteristic to leverage the efficacy of generated electricity. Through the strategic arrangement of the metal electrodes on rGO membrane, the open-circuit voltage (Voc) and short-circuit current (Isc) have exhibited a remarkable augmentation, reaching 1.05 V and 31.6 µA, respectively. The demonstration of effectively tailoring carrier dynamics via electrode configuration expands the practicality by achieving high power density and elucidating how the water-induced carrier density modulation occurs in 2D nanomaterials.

Ultraclean Suspended Graphene by Radiolysis of Adsorbed Water

Access to intrinsic properties of a 2D material is challenging due to the absence of a bulk that would dominate over surface contamination, and this lack of bulk also precludes effective conventional cleaning methods that are almost always sacrificial. Suspended graphene and carbon contaminants represent the most salient challenge. This work has achieved ultraclean graphene, attested by electron energy loss (EEL) spectra unprecedentedly exhibiting fine-structure features expected from bonding and band structure. In the cleaning process in a transmission electron microscope, radicals generated by radiolysis of intentionally adsorbed water remove organic contaminants, which would otherwise be feedstock of the notorious electron irradiation induced carbon deposition. This method can be readily adapted to other experimental settings and other materials to enable previously inhibited undertakings that rely on the intrinsic properties or ultimate thinness of 2D materials. Importantly, the method is surprisingly simple and robust, easily implementable with common lab equipment.

Wetting Transparency of Single-Layer Graphene on Liquid Substrates

Graphene's wetting transparency offers promising avenues for creating multifunctional devices by allowing real-time wettability control on liquid substrates via the flow of different liquids beneath graphene. Despite its potential, direct measurement of floating graphene's wettability remains a challenge, hindering the exploration of these applications. The current study develops an experimental methodology to assess the wetting transparency of single-layer graphene (SLG) on liquid substrates. By employing contact angle measurements and Neumann's Triangle model, the challenge of evaluating the wettability of floating free-suspended single-layer graphene is addressed. The research reveals that for successful contact angle measurements, the testing and substrate liquids must be immiscible. Using diiodomethane as the testing liquid and ammonium persulfate solution as liquid substrate, the study demonstrates the near-complete wetting transparency of graphene. Furthermore, it successfully showcases the feasibility of real-time wettability control using graphene on liquid substrates. This work not only advances the understanding of graphene's interaction with liquid interfaces but also suggests a new avenue for the development of multifunctional materials and devices by exploiting the unique wetting transparency of graphene.

Ecotoxicological Properties of Pure and Phosphorus-Containing Graphene Oxide Bidimensional Sheets in Daphnia magna

In this work, the synthesis and structural, thermal, vibrational, morphological, and electronic characterization of 2D-like pure graphene oxide (GO) and phosphorus-containing graphene oxide (GOP) sheets were investigated. The average thicknesses of GO and GOP were 0.8 μm and 3.1 μm, respectively. The electron energy-loss spectroscopy spectra were used to analyze the differences in the C-K and O-K energy edge bands between GO and GOP. In addition, colloidal stability was studied using dynamic light scattering and zeta potential physicochemical techniques, determining that as the concentration increases, the hydrodynamic diameter and electrostatic stability of GO and GOP increase. The colloidal stability was quite important to ensure the interaction between the suspended solid phase and the biomarker. The 2D-like materials were used to determine their ecotoxicological properties, such as the medium lethal concentration, a crucial parameter for understanding ecotoxicity. Acute ecotoxicity experiments (24 h) were conducted in triplicate to obtain robust statistics, with corresponding mean lethal concentration (LC50) of 11.4 mg L-1 and 9.8 mg L-1 for GO and GOP, respectively. The morphological parameters of GO and GOP were compared with a negative control. However, only the case of GO was analyzed, since the Daphnia magna (D. magna) set exposed to GOP died before completing the time required for morphological analysis. The results indicate that the GOP sample is more toxic than the GO, both during and after exposure. Furthermore, the morphological parameters with the greatest statistically significant changes (p<0.05) were associated with the heart and body, while the eye and tail showed less significant changes.

Redox-Active Phenanthrenequinone Molecules and Nitrogen-Doped Reduced Graphene Oxide as Active Material Composites for Supercapacitor Applications

Carbon-based supercapacitor electrodes are generally restricted in energy density, as they rely exclusively on electric double-layer capacitance (EDLC). The introduction of redox-active organic molecules to obtain pseudocapacitance is a promising route to develop electrode materials with improved energy densities. In this work, we develop a porous nitrogen-doped reduced graphene oxide and 9,10-phenanthrenequinone composite (N-HtrGO/PQ) via a facile one-step physical adsorption method. The electrochemical evaluation of N-HtrGO/PQ using cyclic voltammetry showed a high capacitance of 605 F g-1 in 1 M H2SO4 when the composite consisted of 30% 9,10-phenanthrenequinone and 70% N-HtrGO. The measured capacitance significantly exceeded pure N-HtrGO without the addition of redox-active molecules (257 F g-1). In addition to promising capacitance, the N-HtrGO/30PQ composite showed a capacitance retention of 94.9% following 20,000 charge/discharge cycles. Based on Fourier transform infrared spectroscopy, we postulate that the strong π-π interaction between PQ molecules and the N-HtrGO substrate enhances the specific capacitance of the composite by shortening pathways for electron transfer while improving structural stability.

The effect of water on gold supported chiral graphene nanoribbons: rupture of conjugation by an alternating hydrogenation pattern

In the last few years we have observed a breakpoint in the development of graphene-derived technologies, such as liquid phase filtering and their application to electronics. In most of these cases, they imply exposure of the material to solvents and ambient moisture, either in the fabrication of the material or the final device. The present study demonstrates the sensitivity of graphene nanoribbon (GNR) zigzag edges to water, even in extremely low concentrations. We have addressed the unique reactivity of (3,1)-chiral GNR with moisture on Au(111). Water shows a reductive behaviour, hydrogenating the central carbon of the zigzag segments. By combining scanning tunnelling microscopy (STM) with simulations, we demonstrate how their reactivity reaches a thermodynamic limit when half of the unit cells are reduced, resulting in an alternating pattern of hydrogenated and pristine unit cells starting from the terminal segments. Once a quasi-perfect alternation is reached, the reaction stops regardless of the water concentration. The hydrogenated segments limit the electronic conjugation of the GNR, but the reduction can be reversed both by tip manipulation and annealing. Selective tip-induced dehydrogenation allowed the stabilization of radical states at the edges of the ribbons, while the annealing of the sample completely recovered the original, pristine GNR.

Size Matters: Free-Energy Calculations of Amino Acid Adsorption over Pristine Graphene

There is still growing interest in graphene interactions with proteins, both for its possible biological applications and due to concerns over detrimental effects at the cellular level. As with any process involving proteins, an understanding of amino acid composition is desirable. In this work, we systematically studied the adsorption process of amino acids onto pristine graphene via rigorous free-energy calculations. We characterized the free energy, potential energy, and entropy of the adsorption of all proteinogenic amino acids. The energetic components were further separated into pair interaction contributions. A linear correlation was found between the free energy and the solvent accessible surface area change during adsorption (ΔSASAads) over pristine graphene and uncharged amino acids. Free energies over pristine graphene were compared with adsorption onto graphene oxide, finding an almost complete loss of the favorability of amino acid adsorption onto graphene. Finally, the correlation with ΔSASAads was used to successfully predict the free energy of adsorption of several penta-l-peptides in different structural states and sequences. Due to the relative ease of calculating the ΔSASAads compared to free-energy calculations, it could prove to be a cost-effective predictor of the free energy of adsorption for proteins onto nonpolar surfaces.

Dielectric-free electrowetting on graphene

Electrowetting is a simple way to induce the spreading and retraction of electrolyte droplets. This method is widely used in "device" applications, where a dielectric layer is applied between the electrolyte and the conducting substrate. Recent work, including contributions from our own laboratory, have shown that reversible electrowetting can be achieved directly on conductors. We have shown that graphite surfaces, in particular when combined with highly concentrated electrolyte solutions, show a strong wetting effect. The process is driven by the interactions between the electrolyte ions and the surface, hence models of double-layer capacitance are able to explain changes in the equilibrium contact angles. Herein, we extend the approach to the investigation of electrowetting on graphene samples of varying thickness, prepared by chemical vapor deposition. We show that the use of highly concentrated aqueous electrolytes induces a clear yet subtle electrowetting response due to the adsorption of ions and the suppression of the negative effect introduced by the surface impurities accumulating during the transfer process. The latter have been previously reported to fully hinder electrowetting at lower electrolyte concentrations. An amplified wetting response is recorded in the presence of strongly adsorbed/intercalated anions in both aqueous and non-aqueous electrolytes. The phenomenon is interpreted based on the anion-graphene interactions and their influence on the energetics of the interface. By monitoring the dynamics of wetting, an irreversible behaviour is identified in all cases as a consequence of the irreversibility of anion adsorption and/or intercalation. Finally, the effect of the underlying reactions on the timescales of wetting is also examined.

Application of a Fluctuating Charge Polarization Model to Large Polyaromatic Hydrocarbons and Graphene Nanoflakes

We present a polarization model incorporating coupled fluctuating charges and point inducible dipoles that is able to accurately describe the dipole polarizabilities of small hydrocarbons and, for sufficiently large graphene nanoflakes, reproduce the classical image potential of an infinite conducting sheet. When our fluctuating charge model is applied to the hexagonal carbon nanoflake C60000 we attain excellent agreement with the image potential and induced charge distribution of a conducting sheet. With the inclusion of inducible dipole terms, the model predicts an image plane of zim = 1.3334 a0, which falls in line with prior estimates for graphene. We consider the case of two charges placed on opposite sides of C60000 and find that the fluctuating charge model reproduces classical electrostatics once again. By testing opposing and similar signs of the external charges, we conclude that an atomically thin molecule or extended system does not fully screen their interaction.

Molecular modeling study on the water-electrode surface interaction in hydrovoltaic energy

The global energy problem caused by the decrease in fossil fuel sources, which have negative effects on human health and the environment, has made it necessary to research alternative energy sources. Renewable energy sources are more advantageous than fossil fuels because they are unlimited in quantity, do not cause great harm to the environment, are safe, and create economic value by reducing foreign dependency because they are obtained from natural resources. With nanotechnology, which enables the development of different technologies to meet energy needs, low-cost and environmentally friendly systems with high energy conversion efficiency are developed. Renewable energy production studies have focused on the development of hydrovoltaic technologies, in which electrical energy is produced by making use of the evaporation of natural water, which is the most abundant in the world. By using nanomaterials such as graphene, carbon nanoparticles, carbon nanotubes, and conductive polymers, hydrovoltaic technology provides systems with high energy conversion performance and low cost, which can directly convert the thermal energy resulting from the evaporation of water into electrical energy. The effect of the presence of water on the generation of energy via the interactions between the ion(s) and the liquid-solid surface can be enlightened by the mechanism of the hydovoltaic effect. Here, we simply try to get some tricky information underlying the hydrovoltaic effect by using DFT/B3LYP/6-311G(d, p) computations. Namely, the physicochemical and electronic properties of the graphene surface with a water molecule were investigated, and how/how much these quantities (or parameters) changed in case of the water molecule contained an equal number of charges were analyzed. In these computations, an excess of both positive charge and negative charge, and also a neutral environment was considered by using the Na+, Cl-, and NaCl salt, respectively.

An Up-to-Date Review on the Remediation of Dyes and Phenolic Compounds from Wastewaters Using Enzymes Immobilized on Emerging and Nanostructured Materials: Promises and Challenges

Addressing the critical issue of water pollution, this review article emphasizes the need to remove hazardous dyes and phenolic compounds from wastewater. These pollutants pose severe risks due to their toxic, mutagenic, and carcinogenic properties. The study explores various techniques for the remediation of organic contaminants from wastewater, including an enzymatic approach. A significant challenge in enzymatic wastewater treatment is the loss of enzyme activity and difficulty in recovery post-treatment. To mitigate these issues, this review examines the strategy of immobilizing enzymes on newly developed nanostructured materials like graphene, carbon nanotubes (CNTs), and metal-organic frameworks (MOFs). These materials offer high surface areas, excellent porosity, and ample anchoring sites for effective enzyme immobilization. The review evaluates recent research on enzyme immobilization on these supports and their applications in biocatalytic nanoparticles. It also analyzes the impact of operational factors (e.g., time, pH, and temperature) on dye and phenolic compound removal from wastewater using these enzymes. Despite promising outcomes, this review acknowledges the challenges for large-scale implementation and offers recommendations for future research to tackle these obstacles. This review concludes by suggesting that enzyme immobilization on these emerging materials could present a sustainable, environmentally friendly solution to the escalating water pollution crisis.

The First-Water-Layer Evolution at the Graphene/Water Interface under Different Electro-Modulated Hydrophilic Conditions Observed by Suspended/Supported Field-Effect-Device Architectures

Interfacial water molecules affect carrier transportation within graphene and related applications. Without proper tools, however, most of the previous works focus on simulation modeling rather than experimental validation. To overcome this obstacle, a series of graphene field-effect transistors (GFETs) with suspended (substrate-free, SF) and supported (oxide-supported, OS) configurations are developed to investigate the graphene-water interface under different hydrophilic conditions. With deionized water environments, in our experiments, the electrical transportation behaviors of the graphene mainly originate from the evolution of the interfacial water-molecule arrangement. Also, these current-voltage behaviors can be used to elucidate the first-water layer at the graphene-water interface. For SF-GFET, our experimental results show positive hysteresis in electrical transportation. These imply highly ordered interfacial water molecules with a separated-ionic distributed structure. For OS-GFET, on the contrary, the negative hysteresis shows the formation of the hydrogen-bond interaction between the interfacial water layer and the SiO₂ substrate under the graphene. This interaction further promotes current conduction through the graphene/water interface. In addition, the net current-voltage relationship also indicates the energy required to change the orientation of the first-layer water molecules during electro-potential change. Therefore, our work gives an insight into graphene-water interfacial evolution with field-effect modulation. Furthermore, this experimental architecture also paves the way for investigating 2D solid-liquid interfacial features.

The Surface Energy of Hydrogenated and Fluorinated Graphene

The surface energy of graphene and its chemical derivatives governs fundamental interfacial interactions like molecular assembly, wetting, and doping. However, quantifying the surface energy of supported two-dimensional (2D) materials, such as graphene, is difficult because (1) they are so thin that electrostatic interactions emanating from the underlying substrate are not completely screened, (2) the contribution from the monolayer is sensitive to its exact chemical state, and (3) the adsorption of airborne contaminants, as well as contaminants introduced during transfer processing, screens the electrostatic interactions from the monolayer and underlying substrate, changing the determined surface energy. Here, we determine the polar and dispersive surface energy of bare, fluorinated, and hydrogenated graphene through contact angle measurements with water and diiodomethane. We accounted for many contributing factors, including substrate surface energies and combating adsorption of airborne contaminants. Hydrogenating graphene raises its polar surface energy with little effect on its dispersive surface energy. Fluorinating graphene lowers its dispersive surface energy with a substrate-dependent effect on its polar surface energy. These results unravel how changing the chemical structure of graphene modifies its surface energy, with applications for hybrid nanomaterials, bioadhesion, biosensing, and thin-film assembly.

Heterogeneous Ice Nucleation Studied with Single-Layer Graphene

Control of heterogeneous ice nucleation (HIN) is critical for applications that range from iceophobic surfaces to ice-templated materials. HIN on 2D materials is a particular interesting topic that still lacks extensive experimental investigations. Here, we focus on the HIN on single-layer graphene (SLG) transferred onto different substrates, including silicon, silica, and thermal oxide on silicon. Complemented by other samples without SLG, we obtain a large range of wetting contact angles (WCAs) from 2° to 95°. All pristine SLG samples exhibit a large contact angle of ∼95°, which is close to the theoretical value of 96° for free-standing SLG, irrespective of the substrate and even in the presence of nanoscale wrinkles on SLG, which are due to the transfer process, indicating that the topographical features have little impact on the wetting behavior. Interestingly, SLG displays changes in hydrophobicity upon repeated water droplet freezing-melting-drying cycles due to a shift in Fermi level and/or enhanced water-substrate polar molecular interactions, likely induced by residual adsorption of H₂O molecules. We found that a 0.04 eV decrease in SLG Fermi level reduces the SLG/water interface energy by ∼6 mJ/m², thereby making SLG less hydrophobic. Counterintuitively, the reduction in SLG/water interface energy and the enhanced hydrophilicity after repeated freezing-melting-evaporation cycles actually decreases the freezing temperature by ∼3-4 °C, thereby slightly retarding rather than enhancing HIN. We also found that the water droplet freezing temperature differed by only ∼1 °C on different substrates with WCAs from 2° to 95°, an intriguing and yet reasonable result that confirms that wettability alone is not a good indicator of HIN capability. The HIN rate is rather determined by the difference between substrate/water and substrate/ice interface energies, which was found to stay almost constant for substrates weakly interacting with water/ice via van der Waals or hydrogen bonds, irrespective of hydrophilicity.

Effect of Layer Orientation and Pore Morphology on Water Transport in Multilayered Porous Graphene

In the present work, the effects on water transport due to the orientation of the layer in the multilayered porous graphene and the different patterns formed when the layer is oriented to some degrees are studied for both circular and non-circular pore configurations. Interestingly, the five-layered graphene membrane with a layer separation of 3.5 Å used in this study shows that the water transport through multilayered porous graphene can be augmented by introducing an angle to certain layers of the multilayered membrane system.

Multifunctional-high resolution imaging plate based on hydrophilic graphene for digital pathology

In the present study, we showed that hydrophilic graphene can serve as an ideal imaging plate for biological specimens. Graphene being a single-atom-thick semi-metal with low secondary electron emission, array tomography analysis of serial sections of biological specimens on a graphene substrate showed excellent image quality with improvedz-axis resolution, without including any conductive surface coatings. However, the hydrophobic nature of graphene makes the placement of biological specimens difficult; graphene functionalized with polydimethylsiloxane oligomer was fabricated using a simple soft lithography technique and then processed with oxygen plasma to provide hydrophilic graphene with minimal damage to graphene. High-quality scanning electron microscopy images of biological specimens free from charging effects or distortion were obtained, and the optical transparency of graphene enabled fluorescence imaging of the specimen; high-resolution correlated electron and light microscopy analysis of the specimen became possible with the hydrophilic graphene plate.

Graphene-Coated PVDF Membranes: Effects of Multi-Scale Rough Structure on Membrane Distillation Performance

Graphene-coated membranes for membrane distillation have been fabricated by using a wet-filtration approach. Graphene nanoplatelets have been deposited onto PVDF membrane surfaces. Morphology and physicochemical properties have been explored to evaluate the changes in the surface topography and related effects on the membrane performance in water desalination. The membranes have been tested in membrane distillation plants by using mixtures of sodium chloride and humic acid. The multi-scale rough structure of the surface has been envisaged to amplify the wetting and fouling resistance of the graphene-coated membranes so that a better flux and full salt rejection have been achieved in comparison with pristine PVDF. Total salt rejection and an increase of 77% in flux have been observed for coated membrane with optimized graphene content when worked with NaCl 0.6 M (DCMD, ΔT ≈ 24 °C) over a test period of 6 h. The experimental findings suggest these novel graphene-coated membranes as promising materials to develop functional membranes for high-performing water desalination.

Additive Manufactured Poly(ε-caprolactone)-graphene Scaffolds: Lamellar Crystal Orientation, Mechanical Properties and Biological Performance

Understanding the mechano-biological coupling mechanisms of biomaterials for tissue engineering is of major importance to assure proper scaffold performance in situ. Therefore, it is of paramount importance to establish correlations between biomaterials, their processing conditions, and their mechanical behaviour, as well as their biological performance. With this work, it was possible to infer a correlation between the addition of graphene nanoparticles (GPN) in a concentration of 0.25, 0.5, and 0.75% (w/w) (GPN0.25, GPN0.5, and GPN0.75, respectively) in three-dimensional poly(ε-caprolactone) (PCL)-based scaffolds, the extrusion-based processing parameters, and the lamellar crystal orientation through small-angle X-ray scattering experiments of extruded samples of PCL and PCL/GPN. Results revealed a significant impact on the scaffold's mechanical properties to a maximum of 0.5% of GPN content, with a significant improvement in the compressive modulus of 59 MPa to 93 MPa. In vitro cell culture experiments showed the scaffold's ability to support the adhesion and proliferation of L929 fibroblasts (fold increase of 28, 22, 23, and 13 at day 13 (in relation to day 1) for PCL, GPN0.25, GPN0.5, and GPN0.75, respectively) and bone marrow mesenchymal stem/stromal cells (seven-fold increase for all sample groups at day 21 in relation to day 1). Moreover, the cells maintained high viability, regular morphology, and migration capacity in all the different experimental groups, assuring the potential of PCL/GPN scaffolds for tissue engineering (TE) applications.

On the effects of induced polarizability at the water-graphene interface via classical charge-on-spring models

Molecular models of the water-graphene interaction are essential to describe graphene in condensed phases. Different challenges are associated with the generation of these models, in particular π-π and dispersion interactions; thus quantum and classical models have been developed and due to the numerical efficiency of the latter, they have been extensively employed. In this work, we have systematically studied, via molecular dynamics, two polarizable graphene models, denominated CCCP and CCCPD, employing the charge-on-spring model of the GROMOS forcefield, both being compatible with the polarizable water models COS/G2 and COS/D2, respectively. These models were compared with non-polarizable graphene and SPC water models. We focused the study on the water-graphene interface in two distinct systems and under the influence of an electric field: one composed of graphene immersed in water and the other composed of graphene with a water droplet above it. In the former, the orientation of water close to the graphene layer is affected by polarizable graphene in comparison to non-polarizable graphene. This effect is emphasised when an electric field is applied. In the latter, carbon polarizability reduced water contact angles, but graphene retained its hydrophobicity and the computed angles are within the experimental data. Given the significant extra computational cost, the use of polarizable models instead of the traditional fixed-charged approach for the graphene-water interaction may be justified when polarizability effects are relevant, for example, when applying relatively strong fields or in very anisotropic systems, such as the vacuum-bulk interface, as these models are more responsive to such conditions.

Review-Hysteresis in Carbon Nano-Structure Field Effect Transistor

In recent decades, the research of nano-structure devices (e.g., carbon nanotube and graphene) has experienced rapid growth. These materials have supreme electronic, thermal, optical and mechanical properties and have received widespread concern in different fields. It is worth noting that gate hysteresis behavior of field effect transistors can always be found in ambient conditions, which may influence the transmission appearance. Many researchers have put forward various views on this question. Here, we summarize and discuss the mechanisms behind hysteresis, different influencing factors and improvement methods which help decrease or eliminate unevenness and asymmetry.

van der Waals Epitaxy of Organic Semiconductor Thin Films on Atomically Thin Graphene Templates for Optoelectronic Applications

ConspectusOrganic semiconductors (OSCs) offer unique advantages with respect to mechanical flexibility, low-cost processing, and tunable properties. The optical and electrical properties of devices based on OSCs can be greatly improved when an OSC is coupled with graphene in a certain manner. Our research group has focused on using graphene as a growth template for OSCs and incorporating such high-quality heterostructures into optoelectronic devices. The idea is that graphene's atomically flat surface with a uniform sp² carbon network can serve as a perfect quasi-epitaxial template for the growth of OSCs. In addition, OSC-graphene heterostructures benefit from graphene's unique characteristics, such as its high charge-carrier mobility, excellent optical transparency, and fascinating mechanical durability and flexibility.However, we have often found that OSC molecules assemble on graphene in unpredictable manners that vary from batch to batch. From observations of numerous research systems, we elucidated the mechanism underlying such poor repeatability and set out a framework to actually control the template effect of graphene on OSCs. In this Account, we not only present our scientific findings in this spectrum of areas but also convey our research scheme to the readers so that similar heterostructure complexes can be systematically studied.We began with experiments showing that the growth of OSCs on a graphene surface was driven by van der Waals interactions and is therefore sensitive to the cleanliness of the graphene surface. Nonetheless, we noted that, even on similarly clean graphene surfaces, the OSC thin film still varied with the underlying substrate. Thanks to the graphene-transfer method and in situ gating methods that we developed, we discovered that the decisive parameter for molecule-graphene interaction (and, hence, for the growth of OSCs on graphene) is the charge density in the graphene. Thus, to prepare a graphene template for high-quality graphene-OSC heterostructures, we controlled the charge density in the graphene to minimize the molecule-graphene interaction. Moreover, the possible charge transfer between OSC molecules and graphene, which induces additional molecule-graphene interactions, should also be taken into account. Eventually, we demonstrated a wide range of optoelectronic applications that benefitted from high-quality OSC-graphene heterostructures fabricated using our proof-of-concept systems.

Fermi-Level Modulation of Chemical Vapor Deposition-Grown Monolayer Graphene via Nanoparticles to Macromolecular Dopants

It is critical to modulate the Fermi level of graphene for the development of high-performance electronic and optoelectronic devices. Here, we have demonstrated the modulation of the Fermi level of chemical vapor deposition (CVD)-grown monolayer graphene (MLG) via doping with nanoparticles to macromolecules such as titanium dioxide nanoparticles (TiO2 NPs), nitric acid (HNO3), octadecyltrimethoxysilane (OTS) self-assembled monolayer (SAM), and poly(3,4-ethylene-dioxythiophene):polystyrene sulfonate (PEDOT:PSS). The electronic properties of pristine and doped graphene samples were investigated by Raman spectroscopy and electrical transport measurements. The right shifting of G and 2D peaks and reduction in 2D to G peak intensity ratio (I 2D/I G) assured that the dopants induced a p-type doping effect. Upon doping, the shifting of the Dirac point towards positive voltage validates the increment of the hole concentration in graphene and thus downward shift of the Fermi level. More importantly, the combination of HNO3/TiO2 NP doping on graphene yields a substantially larger change in the Fermi level of MLG. Our study may be useful for the development of graphene-based high-performance flexible electronic devices.

Hydrophilic, Clean Graphene for Cell Culture and Cryo-EM Imaging

The wettability of graphene is critical for numerous applications but is very sensitive to its surface cleanness. Herein, by clarifying the impact of intrinsic contamination, i.e., amorphous carbon, which is formed on the graphene surface during the high-temperature chemical vapor deposition (CVD) process, the hydrophilic nature of clean graphene grown on single-crystal Cu(111) substrate was confirmed by both experimental and theoretical studies, with an average water contact angle of ∼23°. Furthermore, the wettability of as-transferred graphene was proven to be highly dependent on its intrinsic cleanness, because of which the hydrophilic, clean graphene exhibited improved performance when utilized for cell culture and cryoelectron microscopy imaging. This work not only validates the intrinsic hydrophilic nature of graphene but also provides a new insight in developing advanced bioapplications using CVD-grown clean graphene films.

Ultrathin Lubricant-Infused Vertical Graphene Nanoscaffolds for High-Performance Dropwise Condensation

Lubricant-infused surfaces (LIS) are highly efficient in repelling water and constitute a very promising family of materials for condensation processes occurring in a broad range of energy applications. However, the performance of LIS in such processes is limited by the inherent thermal resistance imposed by the thickness of the lubricant and supporting surface structure, as well as by the gradual depletion of the lubricant over time. Here, we present an ultrathin (∼70 nm) and conductive LIS architecture, obtained by infusing lubricant into a vertically grown graphene nanoscaffold on copper. The ultrathin nature of the scaffold, combined with the high in-plane thermal conductivity of graphene, drastically minimize earlier limitations, effectively doubling the heat transfer performance compared to a state-of-the-art CuO LIS surface. We show that the effect of the thermal resistance to the heat transfer performance of a LIS surface, although often overlooked, can be so detrimental that a simple nanostructured CuO surface can outperform a CuO LIS surface, despite filmwise condensation on the former. The present vertical graphene LIS is also found to be resistant to lubricant depletion, maintaining stable dropwise condensation for at least 24 h with no significant change of advancing contact angle and contact angle hysteresis. The lubricant consumed by the vertical graphene LIS is 52.6% less than that of the existing state-of-the-art CuO LIS, also making the fabrication process more economical.

Carbon-Based Composites as Anodes for Microbial Fuel Cells: Recent Advances and Challenges

Owing to the low price, chemical stability and good conductivity, carbon-based materials have been extensively applied as the anode in microbial fuel cells (MFCs). In this review, apart from the charge storage mechanism and anode requirements, the major work focuses on five categories of carbon-based anode materials (traditional carbon, porous carbon, nano-carbon, metal/carbon composite and polymer/carbon composite). The relationship is demonstrated in depth between the physicochemical properties of the anode surface/interface/bulk (porosity, surface area, hydrophilicity, partical size, charge, roughness, etc.) and the bioelectrochemical performances (electron transfer, electrolyte diffusion, capacitance, toxicity, start-up time, current, power density, voltage, etc.). An outlook for future work is also proposed.

Graphene-Based Electrodes in a Vanadium Redox Flow Battery Produced by Rapid Low-Pressure Combined Gas Plasma Treatments

The development of high-power density vanadium redox flow batteries (VRFBs) with high energy efficiencies (EEs) is crucial for the widespread dissemination of this energy storage technology. In this work, we report the production of novel hierarchical carbonaceous nanomaterials for VRFB electrodes with high catalytic activity toward the vanadium redox reactions (VO²⁺/VO₂ ⁺ and V²⁺/V³⁺). The electrode materials are produced through a rapid (minute timescale) low-pressure combined gas plasma treatment of graphite felts (GFs) in an inductively coupled radio frequency reactor. By systematically studying the effects of either pure gases (O₂ and N₂) or their combination at different gas plasma pressures, the electrodes are optimized to reduce their kinetic polarization for the VRFB redox reactions. To further enhance the catalytic surface area of the electrodes, single-/few-layer graphene, produced by highly scalable wet-jet milling exfoliation of graphite, is incorporated into the GFs through an infiltration method in the presence of a polymeric binder. Depending on the thickness of the proton-exchange membrane (Nafion 115 or Nafion XL), our optimized VRFB configurations can efficiently operate within a wide range of charge/discharge current densities, exhibiting energy efficiencies up to 93.9%, 90.8%, 88.3%, 85.6%, 77.6%, and 69.5% at 25, 50, 75, 100, 200, and 300 mA cm^-2, respectively. Our technology is cost-competitive when compared to commercial ones (additional electrode costs < 100 € m^-2) and shows EEs rivalling the record-high values reported for efficient systems to date. Our work remarks on the importance to study modified plasma conditions or plasma methods alternative to those reported previously (e.g., atmospheric plasmas) to improve further the electrode performances of the current VRFB systems.

How do the doping concentrations of N and B in graphene modify the water adsorption?

Understanding the interaction of water and graphene is crucial for various applications such as water purification, desalination, and electrocatalysis. Experimental and theoretical studies have already investigated water adsorption on N- and B-doped graphene. However, there are no reports available that elucidate the influences of the N and B doping content in graphene on the microscopic geometrical structure and the electronic properties of the adsorbed water. Thus, this work is devoted to solving this problem using self-consistent van der Waals density functional theory calculations. The N and B doping contents of 0.0, 3.1, 6.3, and 9.4% were considered. The results showed that the binding energy of water increases almost linearly as a function of doping content at all concentrations for N-doped graphene but below 6.3% for B-doped graphene. In the linear range, the binding energy increases by approximately 30 meV for each increment of the doping ratio. Analyses of the geometric and electronic structures explained the enhancement of the water-graphene interaction with the variation in doping percentage.

Ultrasonication an intensifying tool for preparation of stable nanofluids and study the time influence on distinct properties of graphene nanofluids - A systematic overview

Optimum ultrasonication time will lead to the better performance for heat transfer in addition to preparation methods and thermal properties of the nanofluids. Nano particles are dispersed in base fluids like water (water-based fluids), glycols (glycol base fluids) &oils at different mass or volume fraction by using different preparation techniques. Significant preparation technique can enhance the stability, effects various parameters & thermo-physical properties of fluids. Agglomeration of the dispersed nano particles will lead to declined thermal performance, thermal conductivity, and viscosity. For better dispersion and breaking down the clusters, Ultrasonication method is the highly influential approach. Sonication hour is unique for different nano fluids depending on their response to several considerations. In this review, systematic investigations showing effect on various physical and thermal properties based on ultrasonication/ sonication time are illustrated. In this analysis it is found that increased power or time of ideal sonication increases the dispersion, leading to higher stable fluids, decreased particle size, higher thermal conductivity, and lower viscosity values. Employing the ultrasonic probe is substantially more effective than ultrasonic bath devices. Low ultrasonication power and time provides best outcome. Various sonication time periods by various research are summarized with respect to the different thermophysical properties. This is first review explaining sonication period influence on thermophysical properties of graphene nanofluids.

Novel adjustable monolayer carbon nitride membranes for high-performance saline water desalination

In this study, via molecular dynamic simulations, we showed that the latest described graphene-like carbon nitride membranes, such as g-C₄N₃, g-C₆N₆, and g-C₃N₄ single-layers, can be used as high-performance membranes for water desalination. In addition to having inherent nanopores and extraordinary mechanical properties, the carbon nitride membranes have high water permeability and strong ion rejection (IR) capability. The important point about carbon nitride membranes is that the open or closed state of the pores can be changed by applying tensile stress and creating a positive strain on the membrane. The effect of the imposed pressure, the tensile strain, the ion concentration, and the effective pore size of the membranes are reported. It is demonstrated that, with the applied tensile strain of 12%, the g-C₆N₆ membrane is the best purification membrane, with a water permeability of 54.16 l cm^-2 d^-1 MPa^-1 and the IR of 100%. Its water permeability is one order of magnitude greater than other one-atom-thick membranes.

Influence of the Electrolyte Salt Concentration on DNA Detection with Graphene Transistors

Liquid-gated Graphene Field-Effect Transistors (GFET) are ultrasensitive bio-detection platforms carrying out the graphene's exceptional intrinsic functionalities. Buffer and dilution factor are prevalent strategies towards the optimum performance of the GFETs. However, beyond the Debye length (λD), the role of the graphene-electrolytes' ionic species interactions on the DNA behavior at the nanoscale interface is complicated. We studied the characteristics of the GFETs under different ionic strength, pH, and electrolyte type, e.g., phosphate buffer (PB), and phosphate buffer saline (PBS), in an automatic portable built-in system. The electrostatic gating and charge transfer phenomena were inferred from the field-effect measurements of the Dirac point position in single-layer graphene (SLG) transistors transfer curves. Results denote that λ_D is not the main factor governing the effective nanoscale screening environment. We observed that the longer λ_D was not the determining characteristic for sensitivity increment and limit of detection (LoD) as demonstrated by different types and ionic strengths of measuring buffers. In the DNA hybridization study, our findings show the role of the additional salts present in PBS, as compared to PB, in increasing graphene electron mobility, electrostatic shielding, intermolecular forces and DNA adsorption kinetics leading to an improved sensitivity.

Monolayer Graphene Transfer onto Hydrophilic Substrates: A New Protocol Using Electrostatic Charging

In the present work, we developed a novel method for transferring monolayer graphene onto four different commercial hydrophilic micro/ultra-filtration substrates. The developed method used electrostatic charging to maintain the contact between the graphene and the target substrate intact during the etching step through the wet transfer process. Several measurement/analysis techniques were used in order to evaluate the properties of the surfaces and to assess the quality of the transferred graphene. The techniques included water contact angle (CA), atomic force microscopy (AFM), and field emission scanning electron microscopy (FESEM). Potassium chloride (KCl) ions were used for the transport study through the developed graphene-based membranes. The results revealed that 70% rejection of KCI ions was recorded for the graphene/polyvinylidene difluoride (PVDF1) membrane, followed by 67% rejection for the graphene/polyethersulfone (PES) membrane, and 65% rejection for graphene/PVDF3 membrane. It was revealed that the smoothest substrate was the most effective in rejecting the ions. Although defects such as tears and cracks within the graphene layer were still evolving in this new transfer method, however, the use of Nylon 6,6 interfacial polymerization allowed sealing the tears and cracks within the graphene monolayer. This enhanced the KCl ions rejection of up to 85% through the defect-sealed graphene/polymer composite membranes.

Graphene memristive synapses for high precision neuromorphic computing

Memristive crossbar architectures are evolving as powerful in-memory computing engines for artificial neural networks. However, the limited number of non-volatile conductance states offered by state-of-the-art memristors is a concern for their hardware implementation since trained weights must be rounded to the nearest conductance states, introducing error which can significantly limit inference accuracy. Moreover, the incapability of precise weight updates can lead to convergence problems and slowdown of on-chip training. In this article, we circumvent these challenges by introducing graphene-based multi-level (>16) and non-volatile memristive synapses with arbitrarily programmable conductance states. We also show desirable retention and programming endurance. Finally, we demonstrate that graphene memristors enable weight assignment based on k-means clustering, which offers greater computing accuracy when compared with uniform weight quantization for vector matrix multiplication, an essential component for any artificial neural network.

Mechanism and Suppression of Physisorbed-Water-Caused Hysteresis in Graphene FET Sensors

Hysteresis is a problem in field-effect transistors (FETs) often caused by defects and charge traps inside a gate isolating (e.g., SiO₂) layer. This work shows that graphene-based FETs also exhibit hysteresis due to water physisorbed on top of graphene determined by the relative humidity level, which naturally happens in biosensors and ambient operating sensors. The hysteresis effect is explained by trapping of electrons by physisorbed water, and it is shown that this hysteresis can be suppressed using short pulses of alternating gate voltages.

Reduced graphene oxide@polydopamine decorated carbon cloth as an anode for a high-performance microbial fuel cell in Congo red/saline wastewater removal

A polydopamine decorated reduced oxide graphene (rGO@PDA) on carbon cloth (CC) as microbial fuel cell (MFC) anode was prepared by using dopamine polymerized reduction of oxide graphene. The anodes provided superhydrophilicity, high conductivity, good biocompatibility and long-term stability due to the combination of inorganic/organic components. These components and the resulting structure promoted enhancement of bacteria growth and enrichment, accelerated extracellular electron transfer between bacteria and anode surface, gained a high-performance rGO@PDA/CC MFC. The device achieved a short startup time of 18 h, maximum power density of 988.1 ± 5.2 mW·m^-2 and Congo red decolorization efficiency of 89.7 ± 2.4% within 24 h. When Congo red and sodium acetate were continuously degraded, removal efficiency of chemical oxygen demand increased 77.8 ± 3.5% and 88.5 ± 5.8%, respectively. Thus, the synergistic effect of rGO and PDA effectively enhanced startup speed, power generation and pollutant degradation. The degradation products of Congo red were analyzed by mass spectrometry. Congo red was degraded to small organic molecules without azo bonds.

Solvent-Solvent Correlations across Graphene: The Effect of Image Charges

Wetting experiments show pure graphene to be weakly hydrophilic, but its contact angle (CA) also reflects the character of the supporting material. Measurements and molecular dynamics simulations on suspended and supported graphene often reveal a CA reduction due to the presence of the supporting substrate. A similar reduction is consistently observed when graphene is wetted from both sides. The effect has been attributed to transparency to molecular interactions across the graphene sheet; however, the possibility of substrate-induced graphene polarization has also been considered. Computer simulations of CA on graphene have so far been determined by ignoring the material's conducting properties. We improve the graphene model by incorporating its conductivity according to the constant applied potential molecular dynamics. Using this method, we compare the wettabilities of suspended graphene and graphene supported by water by measuring the CA of cylindrical water drops on the sheets. The inclusion of graphene conductivity and concomitant polarization effects leads to a lower CA on suspended graphene, but the CA reduction is significantly bigger when the sheets are also wetted from the opposite side. The stronger adhesion is accompanied by a profound change in the correlations among water molecules across the sheet. While partial charges on water molecules interacting across an insulator sheet attract charges of the opposite sign, apparent attraction among like charges is manifested across the conducting graphene. The change is associated with graphene polarization, as the image charges inside the conductor attract equally signed partial charges of water molecules on both sides of the sheet. Additionally, using a nonpolar liquid (diiodomethane), we affirm a detectable wetting translucency when liquid-liquid forces are dominated by dispersive interactions. Our findings are important for predictive modeling toward a variety of applications including sensors, fuel cell membranes, water filtration, and graphene-based electrode materials in high-performance supercapacitors.

Nitrogen-Doped Unusually Superwetting, Thermally Insulating, and Elastic Graphene Aerogel for Efficient Solar Steam Generation

By removing the oxygen-containing functional groups, thermal treatment in inert gas has been widely reported to improve the hydrophobicity of carbon materials. However, this work reports a contrary phenomenon for the nitrogen-doped graphene aerogel (NGA). As the temperature of thermal treatment increases from 200 to 1000 °C, NGA becomes more and more hydrophilic and the superwetting property remains for weeks in air. To uncover this unusual phenomenon, the effect of nitrogen doping is studied through both experiment and MD simulations. The effects of air exposure and air humidity are further investigated in detail to illustrate the whole physical picture clearly. The superwetting behavior is attributed to the preferential adsorption of water molecules to the nitrogen-doped sites, which significantly inhibits airborne hydrocarbon adsorption. In combination with the excellent properties including mechanical elasticity, high light absorption, and good thermal insulation, an efficient photothermal and solar steam generation performance is demonstrated by using NGA-600 as the photothermal material, presenting a high energy conversion efficiency of 86.2% and good recycling stability.

Spatially Resolved Bottom-Side Fluorination of Graphene by Two-Dimensional Substrate Patterning

Patterned functionalization can, on the one hand, open the band gap of graphene and, on the other hand, program demanding designs on graphene. The functionalization technique is essential for graphene-based nanoarchitectures. A new and highly efficient method was applied to obtain patterned functionalization on graphene by mild fluorination with spatially arranged AgF arrays on the structured substrate. Scanning Raman spectroscopy (SRS) and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) were used to characterize the functionalized materials. For the first time, chemical patterning on the bottom side of graphene was realized. The chemical nature of the patterned functionalization was determined to be the ditopic scenario with fluorine atoms occupying the bottom side and moieties, such as oxygen-containing groups or hydrogen atoms, binding on the top side, which provides information about the mechanism of the fluorination process. Our strategy can be conceptually extended to pattern other functionalities by using other reactants. Bottom-side patterned functionalization enables utilization of the top side of a material, thereby opening up the possibilities for applications in graphene-based devices.

Atomic Layer Deposition of High-k Insulators on Epitaxial Graphene: A Review

Due to its excellent physical properties and availability directly on a semiconductor substrate, epitaxial graphene (EG) grown on the (0001) face of hexagonal silicon carbide is a material of choice for advanced applications in electronics, metrology and sensing. The deposition of ultrathin high-k insulators on its surface is a key requirement for the fabrication of EG-based devices, and, in this context, atomic layer deposition (ALD) is the most suitable candidate to achieve uniform coating with nanometric thickness control. This paper presents an overview of the research on ALD of high-k insulators on EG, with a special emphasis on the role played by the peculiar electrical/structural properties of the EG/SiC (0001) interface in the nucleation step of the ALD process. The direct deposition of Al2O3 thin films on the pristine EG surface will be first discussed, demonstrating the critical role of monolayer EG uniformity to achieve a homogeneous Al2O3 coverage. Furthermore, the ALD of several high-k materials on EG coated with different seeding layers (oxidized metal films, directly deposited metal-oxides and self-assembled organic monolayers) or subjected to various prefunctionalization treatments (e.g., ozone or fluorine treatments) will be presented. The impact of the pretreatments and of thermal ALD growth on the defectivity and electrical properties (doping and carrier mobility) of the underlying EG will be discussed.

Massive and massless charge carriers in an epitaxially strained alkali metal quantum well on graphene

We show that Cs intercalated bilayer graphene acts as a substrate for the growth of a strained Cs film hosting quantum well states with high electronic quality. The Cs film grows in an fcc phase with a substantially reduced lattice constant of 4.9 Å corresponding to a compressive strain of 11% compared to bulk Cs. We investigate its electronic structure using angle-resolved photoemission spectroscopy and show the coexistence of massless Dirac and massive Schrödinger charge carriers in two dimensions. Analysis of the electronic self-energy of the massive charge carriers reveals the crystallographic direction in which a two-dimensional Fermi gas is realized. Our work introduces the growth of strained metal quantum wells on intercalated Dirac matter.

Cesium atoms that are grown on intercalated bilayer graphene can create an ordered epitaxial film. Here, the authors report that such a strained film can host quantum well states with high electronic quality as characterized through angle-resolved photoemission spectroscopy.

Charge-Transfer-Controlled Growth of Organic Semiconductor Crystals on Graphene

Controlling the growth behavior of organic semiconductors (OSCs) is essential because it determines their optoelectronic properties. In order to accomplish this, graphene templates with electronic-state tunability are used to affect the growth of OSCs by controlling the van der Waals interaction between OSC ad-molecules and graphene. However, in many graphene-molecule systems, the charge transfer between an ad-molecule and a graphene template causes another important interaction. This charge-transfer-induced interaction is never considered in the growth scheme of OSCs. Here, the effects of charge transfer on the formation of graphene-OSC heterostructures are investigated, using fullerene (C60) as a model compound. By in situ electrical doping of a graphene template to suppress the charge transfer between C60 ad-molecules and graphene, the layer-by-layer growth of a C60 film on graphene can be achieved. Under this condition, the graphene-C60 interface is free of Fermi-level pinning; thus, barristors fabricated on the graphene-C60 interface show a nearly ideal Schottky-Mott limit with efficient modulation of the charge-injection barrier. Moreover, the optimized C60 film exhibits a high field-effect electron mobility of 2.5 cm2 V-1 s-1. These results provide an efficient route to engineering highly efficient optoelectronic graphene-OSC hybrid material applications.

Merging versatile polymer chemistry with multifunctional nanoparticles: an overview of crosslinkable aromatic polyester matrix nanocomposites

The current trend in the global advanced material market is expeditiously shifting towards more lightweight, multifunctional configurations, considering very recent developments in electrical aircraft, biomedical devices, and autonomous automobiles. Hence, the development of novel polymer nanocomposite materials is critical to advancing the current state-of-the-art of structural material technologies to address the pressing performance demands. Aiming at expanding the existing material design space, we have investigated crosslinkable aromatic polyester matrix nanocomposites. Aromatic polyesters, in the thermosetting form, are a prospective high-performance/high-temperature polymer technology, which is on a par with conventional epoxy-derivative resins and high-performance engineering thermoplastics in the range of their potential applications. The aromatic matrix-based thermosetting nanocomposites manifest greatly enhanced physical properties enabled by a chemistry-favored robust interfacial covalent coupling mechanism developed during the in situ polymerization reaction with various nanofiller particle configurations. Here, we provide a summary review of our recent efforts in developing this novel polymer nanocomposite material system. We highlight the chemical strategy, fabrication approach, and processing techniques developed to obtain various nanocomposite representations for structural, electrical, optical, biomedical, and tribological applications. The unique characteristic features emerging in the nanocomposite morphologies, along with their physicochemical effects on the multifunctional macroscale properties, are demonstrated. This unique matrix configuration introduces superior performance elements to polymer nanocomposite applications towards designing advanced composite materials.