High Mobility Indium Oxide Electron Transport Layer for an Efficient Charge Extraction and Optimized Nanomorphology in Organic Photovoltaics

In-Doped ZnO Electron Transport Layer for High-Efficiency Ultrathin Flexible Organic Solar Cells

Sol-gel processed zinc oxide (ZnO) is one of the most widely used electron transport layers (ETLs) in inverted organic solar cells (OSCs). The high annealing temperature (≈200 °C) required for sintering to ensure a high electron mobility however results in severe damage to flexible substrates. Thus, flexible organic solar cells based on sol-gel processed ZnO exhibit significantly lower efficiency than rigid devices. In this paper, an indium-doping approach is developed to improve the optoelectronic properties of ZnO layers and reduce the required annealing temperature. Inverted OSCs based on In-doped ZnO (IZO) exhibit a higher efficiency than those based on ZnO for a range of different active layer systems. For the PM6:L8-BO system, the efficiency increases from 17.0% for the pristine ZnO-based device to 17.8% for the IZO-based device. The IZO-based device with an active layer of PM6:L8-BO:BTP-eC9 exhibits an even higher efficiency of up to 18.1%. In addition, a 1.2-micrometer-thick inverted ultrathin flexible organic solar cell is fabricated based on the IZO ETL that achieves an efficiency of 17.0% with a power-per-weight ratio of 40.4 W g-1, which is one of the highest efficiency for ultrathin (less than 10 micrometers) flexible organic solar cells.

Interface-Engineered Organic Near-Infrared Photodetector for Imaging Applications

We report a high-speed low dark current near-infrared (NIR) organic photodetector (OPD) on a silicon substrate with amorphous indium gallium zinc oxide (a-IGZO) as the electron transport layer (ETL). In-depth understanding of the origin of dark current is obtained using an elaborate set of characterization techniques, including temperature-dependent current-voltage measurements, current-based deep-level transient spectroscopy (Q-DLTS), and transient photovoltage decay measurements. These characterization results are complemented by energy band structures deduced from ultraviolet photoelectron spectroscopy. The presence of trap states and a strong dependency of activation energy on the applied reverse bias voltage point to a dark current mechanism based on trap-assisted field-enhanced thermal emission (Poole-Frenkel emission). We significantly reduce this emission by introducing a thin interfacial layer between the donor: acceptor blend and the a-IGZO ETL and obtain a dark current as low as 125 pA/cm² at an applied reverse bias of -1 V. Thanks to the use of high-mobility metal-oxide transport layers, a fast photo response time of 639 ns (rise) and 1497 ns (fall) is achieved, which, to the best of our knowledge, is among the fastest reported for NIR OPDs. Finally, we present an imager integrating the NIR OPD on a complementary metal oxide semiconductor read-out circuit, demonstrating the significance of the improved dark current characteristics in capturing high-quality sample images with this technology.

Heterojunction Transistors Printed via Instantaneous Oxidation of Liquid Metals

Semiconducting transparent metal oxides are critical high mobility materials for flexible optoelectronic devices such as displays. We introduce the continuous liquid metal printing (CLMP) technique to enable rapid roll-to-roll compatible deposition of semiconducting two-dimensional (2D) metal oxide heterostructures. We leverage CLMP to deposit 10 cm²-scale nanosheets of InO_x and GaO_x in seconds at a low process temperature (T < 200 °C) in air, fabricating heterojunction thin film transistors with 100× greater I_on/I_off, 4× steeper subthreshold slope, and a 50% increase in mobility over pure InO_x channels. Detailed nanoscale characterization of the heterointerface by X-ray photoelectron spectroscopy, UV-vis, and Kelvin probe elucidates the origins of enhanced electronic transport in these 2D heterojunctions. This combination of CLMP with the electrostatic control induced by the heterostructure architecture leads to high performance (μ_lin up to 22.6 cm²/(V s)) while reducing the process time for metal oxide transistors by greater than 100× compared with sol-gels and vacuum deposition methods.

Hole/Electron Transporting Materials for Nonfullerene Organic Solar Cells

Nonfullerene acceptor based organic solar cells (NF-OSCs) have witnessed rapid progress over the past few years owing to the intensive research efforts on novel electron donor and nonfullerene acceptor (NFA) materials, interfacial engineering, and device processing techniques. Interfacial layers including electron transporting layers (ETL) and hole transporting layers (HTLs) are crucially important in the OSCs for facilitating electron and hole extraction from the photoactive blend to the respective electrodes. In this review, the lates progress in both ETLs and HTLs for the currently prevailing NF-OSCs are discussed, in which the ETLs are summarized from the categories of metal oxides, metal chelates, non-conjugated electrolytes and conjugated electrolytes, and the HTLs are summarized from the categories of inorganic and organic materials. In addition, some bifunctional interlayer materials served as both ETLs and HTLs are also introduced. Finally, the prospects of ETL/HTL materials for NF-OSCs are provided.

Efficient Gradient Potential Top Electron Transport Structures Achieved by Combining an Oxide Family for Inverted Perovskite Solar Cells with High Efficiency and Stability

Although inverted (p-i-n) structure perovskite solar cells (PSCs) have achieved high efficiency by commonly using fullerenes or their derivatives as electron transport layers (ETLs), the device stability and cost of fullerene materials are still of great concern. Herein, we demonstrate inorganic top ETLs simply composed from a family of metal oxides including In₂O₃ and its derivative of Sn:In₂O₃ with a gradient potential structure. For inverted PSCs, the typical film formation process of In₂O₃ will damage or degrade perovskite materials underneath; thus, we report a low temperature synthesis approach for obtaining In₂O₃ and Sn:In₂O₃ nanoparticles that can form effective top ETLs without any post-treatment. The one-family oxide-based top ETL features with the enhanced built-in potential, high electron extraction, and low interfacial recombination, offering a power conversion efficiency (PCE) of 20.65% in PSCs constructed from oxide-only carrier (both hole and electron) transport layers (CTLs), which is the highest efficiency in oxide-only CTL-based inverted PSCs to the best of our knowledge. Equally important, the inverted PSCs based on the Sn:In₂O₃/In₂O₃ ETL show the excellent operational stability and remain 90% of the initial value of PCE over 2000 h. Consequently, this work contributes to the robust strategy of all oxide-only CTLs in developing rigid and flexible PSCs for practical photovoltaic applications.

Divalent Cation Dependence Enhances Dopamine Aptamer Biosensing

Oligonucleotide receptors (aptamers), which change conformation upon target recognition, enable electronic biosensing under high ionic-strength conditions when coupled to field-effect transistors (FETs). Because highly negatively charged aptamer backbones are influenced by ion content and concentration, biosensor performance and target sensitivities were evaluated under application conditions. For a recently identified dopamine aptamer, physiological concentrations of Mg²⁺ and Ca²⁺ in artificial cerebrospinal fluid produced marked potentiation of dopamine FET-sensor responses. By comparison, divalent cation-associated signal amplification was not observed for FET sensors functionalized with a recently identified serotonin aptamer or a previously reported dopamine aptamer. Circular dichroism spectroscopy revealed Mg²⁺- and Ca²⁺-induced changes in target-associated secondary structure for the new dopamine aptamer, but not the serotonin aptamer nor the old dopamine aptamer. Thioflavin T displacement corroborated the Mg²⁺ dependence of the new dopamine aptamer for target detection. These findings imply allosteric binding interactions between divalent cations and dopamine for the new dopamine aptamer. Developing and testing sensors in ionic environments that reflect intended applications are best practices for identifying aptamer candidates with favorable attributes and elucidating sensing mechanisms.

Introduction of Siloxane-Terminated Side Chains into Semiconducting Polymers To Tune Phase Separation with Nonfullerene Acceptor for Polymer Solar Cells

In this work, five PTB7-Th-based conjugated polymers (PTB7-Th, PTBSi20, PTBSi25, PTBSi33, and PTBSi100) with different contents of siloxane-terminated pentyl side chain were synthesized, and properties of corresponding blend films with narrow band gap nonfullerene IEICO-4F acceptor were extensively investigated. According to the contact angle testing, the PTB7-Th with 100% alkyl side chain and PTBSi100 100% siloxane-terminated side chain on the benzodithiophene unit showed surface energy values of 40.04 and 34.52 mJ/m², respectively. The results demonstrate that relative to alkyl side chain in PTB7-Th, the siloxane-terminated side chain could effectively reduce the surface energy of a resulting polymer. Based on Flory-Huggins interaction parameter estimations, the miscibility between the polymer and IEICO-4F would vary in an order of PTB7-Th > PTBSi20 > PTBSi25 > PTBSi33 > PTBSi100, suggesting that siloxane-terminated side chain would afford a tunable driving force for phase separation. Transmission electron microscopy and Raman mapping could confirm large bulk domains inside the PTBSi100:IEICO-4F blend film. In polymer solar cells, the blend film of the PTBSi100 with the lowest miscibility to IEICO-4F showed an undesirable power conversion efficiency (PCE) of 8.52%, which was significantly lower than that of 11.23% for PTB7-Th, suggesting that too large phase separation driving force is not beneficial for the device performance. Side-chain random copolymers PTBSi20, PTBSi25, and PTBSi33 for fine tuning could display PCEs of 11.94, 12.61, and 11.80%, respectively, all higher than that of PTB7-Th. Our results not only reveal the big surface energy difference between the siloxane-terminated side chain and the common alkyl side chain but also provide a guideline for side chain engineering of conjugated polymer donors with tunable morphology and optimal matching with a nonfullerene acceptor.

Role of Molecular and Interchain Ordering in the Formation of a δ-Hole-Transporting Layer in Organic Solar Cells

Interface engineering, especially the realization of Ohmic contacts at the interface between organic semiconductors and metal contacts, is one of the essential preconditions to achieve high-efficiency organic electronic devices. Here, the interface structures of polymer/fullerene blends are correlated with the charge extraction/injection properties of working organic solar cells. The model system-poly(3-hexylthiophene) (P3HT):phenyl-C₆₁-butyric acid methyl ester (PCBM)-is fabricated using two different degrees of P3HT regioregularity to alter the blend interchain order and molecular packing, resulting in different device performances. Investigations by electroabsorption spectroscopy on these devices indicate a significant reduction (≈1 V) in the built-in potential with an increase in the P3HT regioregularity. This observation is also supported by a change in the work function (WF) of high regioregular polymer blends from photoelectron spectroscopy measurements. These results confirm the presence of a strong dipole layer acting as a δ-hole-transporting layer at the polymer/MoO₃/Ag electrode interface. Unipolar hole-only devices show an increase in the magnitude of the hole current in high regioregular P3HT devices, suggesting an increase in the hole injection/extraction efficiency inside the device with a δ-hole-transporting layer. Microscopically, near-edge X-ray absorption fine structure spectroscopy was conducted to probe the surface microstructure in these blends, finding a highly edge-on orientation of P3HT chains in blends made with high regioregular P3HT. This edge-on orientation of P3HT chains at the interface results in a layer of oriented alkyl side chains capping the surface, which favors the formation of a dipole layer at the polymer/MoO₃ interface. The increase in the charge extraction efficiency due to the formation of a δ-hole-transporting layer thus results in higher short circuit currents and fill factor values, eventually increasing the device efficiency in high regioregular P3HT devices despite a slight decrease in cell open circuit voltage. These findings emphasize the significance of WF control as a tool for improved device performance and pave the way toward interfacial optimization based on the modulation of fundamental polymer properties, such as polymer regioregularity.

Influence Mechanism of Cu Layer Thickness on Photoelectric Properties of IWO/Cu/IWO Films

Transparent conductive IWO/Cu/IWO (W-doped In₂O₃) films were deposited on quartz substrates by magnetron sputtering of IWO and Cu in the Ar atmosphere. The X-ray diffraction (XRD) patterns identified the cubic iron-manganese ore crystal structure of the IWO layers. The influence of the thickness of the intermediate ultra-thin Cu layers on the optical and electrical properties of the multilayer films was analyzed. As the Cu layer thickness increases from 4 to 10 nm, the multilayer resistivity gradually decreases to 4.5 × 10^-4 Ω·cm, and the optical transmittance in the mid-infrared range increases first and then decreases with a maximum of 72%, which serves as an excellent candidate for the mid-infrared transparent electrode.

Strontium Fluoride and Zinc Oxide Stacked Structure as an Interlayer in High-Performance Inverted Polymer Solar Cells

Enhanced power conversion efficiency is reported in inverted polymer solar cells when an ultrathin layer of strontium fluoride (SrF₂) is evaporated on the surface of the solution-processed zinc oxide (ZnO) electron transport layer. The photoactive layer is made up of bulk heterojunction composites of poly[4,8-bis(5(2-ethylhexyl)thiophen-2-yl)benzo[1,2- b:4,5- b']dithiopheneco-3-fluorothieno[3,4- b]-thiophene-2-carboxylate] and [6,6]-phenyl-C₇₁-butyric acid methyl ester. The ZnO film acts as an effective electron transport layer, whereas the ultrathin SrF₂ layer improves the energy level alignment and enhances the built-in potential via the formation of an interfacial dipole layer at the interfaces between the ZnO film and the photoactive layer, resulting in an enhanced electron extraction efficiency and a decreased carrier recombination loss. Furthermore, the SrF₂ layer reduces the inherent incompatibility between the hydrophilic ZnO film and the hydrophobic photoactive layer. As a result, all the photovoltaic performance parameters are remarkably improved, leading to a high efficiency of up to 10.46% (with a fill factor of 71.38%), corresponding to a ca. 21% improvement over the reference device performance (8.64%). The use of a ZnO/SrF₂ stacked interlayer provides a simple, but effective, approach to obtain high-efficiency inverted PSCs.

Recent Developments in the Optimization of the Bulk Heterojunction Morphology of Polymer: Fullerene Solar Cells

Organic photovoltaic (OPV) devices, made with semiconducting polymers, have recently attained a power conversion efficiency (PCE) over 14% in single junction cells and over 17% in tandem cells. These high performances, together with the suitability of the technology to inexpensive large-scale manufacture, over lightweight and flexible plastic substrates using roll-to-roll (R2R) processing, place the technology amongst the most promising for future harvesting of solar energy. Although OPVs using non-fullerene acceptors have recently outperformed their fullerene-based counterparts, the research in the development of new fullerenes and in the improvement of the bulk-heterojunction (BHJ) morphology and device efficiency of polymer:fullerene solar cells remains very active. In this review article, the most relevant research works performed over the last 3 years, that is, since the year 2016 onwards, in the field of fullerene-based polymer solar cells based on the copolymers PTB7, PTB7-Th (also known as PBDTTT-EFT) and PffBT4T-2OD, are presented and discussed. This review is primarily focused on studies that involve the improvement of the BHJ morphology, efficiency and stability of small active area devices (typically < 15 mm²), through the use of different processing strategies such as the use of different fullerene acceptors, different processing solvents and additives and different thermal treatments.

High Efficiency Non-fullerene Organic Tandem Photovoltaics Based on Ternary Blend Subcells

The application of tandem structure that integrates multiple subcells into one device is a promising way to realize high efficiency organic solar cells. However, current-matching among different subcells remains as the main challenge for organic tandem photovoltaics. Here, we provide a facile approach to achieve a good current matching via engineering the chemical composition of non-fullerene ternary blend subcells. For the front subcell, a ternary blend of PDBT-T1:TPH-Se:ITIC is selected due to its good thermal stability. The amorphous nature of TPH-Se can sufficiently suppress the unfavorable phase separation of blends during the heat treatment, enabling a sintering in the fabrication of high quality interconnecting layer. A double-junction tandem device is fabricated with a rear subcell consisting of PBDB-T:ITIC. After the optimization of the chemical composition of the front subcell, the power conversion efficiency (PCE) of double-junction tandem device increased from 10.6% using PDBT-T1:TPH-Se binary front subcell to 11.5% using PDBT-T1:TPH-Se:ITIC (1:0.9:0.1) ternary front subcell due to better current matching. In order to further enhance the light absorption in the near-infrared region, a third junction PBDTTT-EFT:IEICO-4F is introduced. The champion cell of triple-junction non-fullerene tandem solar cell achieves a PCE of 13.0% with a high open circuit voltage of 2.52 V.