Tailoring the Antimicrobial Response of Cationic Nanocellulose-Based Foams through Cryo-Templating

Periodate oxidation-mediated nanocelluloses: Preparation, functionalization, structural design, and applications

In recent years, the remarkable progress in nanotechnology has ignited considerable interest in investigating nanocelluloses, an environmentally friendly and sustainable nanomaterial derived from cellulosic feedstocks. Current research primarily focuses on the preparation and applications of nanocelluloses. However, to enhance the efficiency of nanofibrillation, reduce energy consumption, and expand nanocellulose applications, chemical pre-treatments of cellulose fibers have attracted substantial interest and extensive exploration. Various chemical pre-treatment methods yield nanocelluloses with diverse functional groups. Among these methods, periodate oxidation has garnered significant attention recently, due to the formation of dialdehyde cellulose derived nanocellulose, which exhibits great promise for further modification with various functional groups. This review seeks to provide a comprehensive and in-depth examination of periodate oxidation-mediated nanocelluloses (PONCs), including their preparation, functionalization, hierarchical structural design, and applications. We believe that PONCs stand as highly promising candidates for the development of novel nano-cellulosic materials.

Preparation and functionalization of cellulose nanofibers using a naturally occurring acid and their application in stabilizing linseed oil/water Pickering emulsions

Finding efficient and environmental-friendly methods to produce and chemically modify cellulose nanofibers (CNFs) remains a challenge. In this study, lactic acid (LA) treatment followed by microfluidization was employed for the isolation and functionalization of CNFs. Small amounts of HCl (0.01, 0.1, and 0.2 M) were used alongside LA to intensify cellulose hydrolysis. FTIR spectroscopy and solid-state 13C NMR confirmed the successful functionalization of CNFs with lactyl groups during isolation, while SEM, AFM, and rheological tests revealed that the addition of HCl governed the fibers' sizes and morphology. Notably, the treatment with LA and 0.2 M HCl resulted in a more efficient defibrillation, yielding smaller nanofibers sizes (62 nm) as compared to the treatment with LA or HCl alone (90 and 108 nm, respectively). The aqueous suspension of CNFs treated with LA and 0.2 M HCl showed the highest viscosity and storage modulus. LA-modified CNFs were tested as stabilizers for linseed oil/water (50/50 v/v) emulsions. Owing to the lactyl groups grafted on their surface and higher aspect ratio, CNFs produced with 0.1 and 0.2 M HCl led to emulsions with increased stability (a creaming index increase of only 3 % and 1 %, respectively, in 30 days) and smaller droplets sizes of 23.4 ± 1.2 and 35.5 ± 0.5 μm, respectively. The results showed that LA-modified CNFs are promising stabilizers for Pickering emulsions.

Phosphorylated cellulose nanocrystals: Optimizing production by decoupling hydrolysis and surface modification

Urea and phosphoric acid are essential for the isolation of phosphorylated cellulose nanocrystals (CNCs). Besides limiting dissolution of nanocrystals, urea facilitates the swelling of fibres thus increasing access for the phosphorylating agent. The aim of this study was to determine optimal conditions for isolation of highly charged phosphorylated CNCs. Using a design of experiments approach, seventeen experiments in which reaction time, urea, and acid concentrations were varied, were conducted. A two-step process was used, in which CNCs were first isolated by treatment in phosphoric acid, and then treated with metaphosphoric acid, and urea. It is shown that a design of experiments approach to the phosphorylation of CNCs allows a much lower ratio of urea to acid than has previously been reported. CNCs with high surface charge (~1800 mmol kg-1) are possible using this method. This information is instructive to phosphorylation of cellulose nanomaterials which have a variety of applications e.g., water purification and medical biomaterials.

Dialdehyde modified and cationic aerogel for efficient microplastics adsorption from environmental waters

Recent reports had shown that microplastics could be transferred to organisms through various channels, severely and adversely affecting organisms' health and their physiological functions. Therefore, there remained an urgency to adopt an effective and environmentally friendly method to extract microplastics from water. In this paper, a cationic-modified d-DCPG aerogel with a three-dimensional network structure was successfully prepared by a directional freeze-drying technology in which double-aldehyde-modified cellulose nanofiber (CNF) was used as the matrix, betaine chloride hydrazide (GT) provided modification, and polyvinyl alcohol (PVA) provided cross-linking function. Aerogels had an excellent adsorption capacity (145.05 mg/g) for microplastics in aqueous environment, and when the pH was from 10 to 4, it exhibited an excellent adsorption efficiency from 90.01 % to 97.61 %; an excellent adsorption efficiency after 8 cycles (>89 %); pseudo-second-order kinetics and Freundlich adsorption isotherm had a high fitting effects on the adsorption process and adsorption results, respectively. And ultraviolet analysis also verified the occurrence of adsorption behavior. These results showed that d-DCPG aerogels had an excellent application prospects in microplastics removal in river, lake, reservoir, and marine environments.

Dialdehyde carbohydrates - Advanced functional materials for biomedical applications

Dialdehyde carbohydrates (DCs) have found applications in a wide range of biomedical field due to their great versatility, biocompatibility/biodegradability, biological properties, and controllable chemical/physical characteristics. The presence of dialdehyde groups in carbohydrate structure allows cross-linking of DCs to form versatile architectures serving as interesting matrices for biomedical applications (e.g., drug delivery, tissue engineering, and regenerative medicine). Recently, DCs have noticeably contributed to the development of diverse physical forms of advanced functional biomaterials i.e., bulk architectures (hydrogels, films/coatings, or scaffolds) and nano/-micro formulations. We underline here the current scientific knowledge on DCs, and demonstrate their potential and newly developed biomedical applications. Specifically, an update on the synthesis approach and functional/bioactive attributes is provided, and the selected in vitro/in vivo studies are reviewed comprehensively as examples of the latest progress in the field. Moreover, safety concerns, challenges, and perspectives towards the application of DCs are deliberated.

Metal nanoparticles and carbohydrate polymers team up to improve biomedical outcomes

The convergence of carbohydrate polymers and metal nanoparticles (MNPs) holds great promise for biomedical applications. Researchers aim to exploit the capability of carbohydrate matrices to modulate the physicochemical properties of MNPs, promote their therapeutic efficiency, improve targeted drug delivery, and enhance their biocompatibility. Therefore, understanding various attributes of both carbohydrates and MNPs is the key to harnessing them for biomedical applications. The many distinct types of carbohydrate-MNP systems confer unique capabilities for drug delivery, wound healing, tissue engineering, cancer treatment, and even food packaging. Here, we introduce distinct physicochemical/biological properties of carbohydrates and MNPs, and discuss their potentials and shortcomings (alone and in combination) for biomedical applications. We then offer an overview on carbohydrate-MNP systems and how they can be utilized to improve biomedical outcomes. Last but not least, future perspectives toward the application of such systems are highlighted.

Nanocellulose-based porous materials: Regulation and pathway to commercialization in regenerative medicine

We review the recent progress that have led to the development of porous materials based on cellulose nanostructures found in plants and other resources. In light of the properties that emerge from the chemistry, shape and structural control, we discuss some of the most promising uses of a plant-based material, nanocellulose, in regenerative medicine. Following a brief discussion about the fundamental aspects of self-assembly of nanocellulose precursors, we review the key strategies needed for material synthesis and to adjust the architecture of the materials (using three-dimensional printing, freeze-casted porous materials, and electrospinning) according to their uses in tissue engineering, artificial organs, controlled drug delivery and wound healing systems, among others. For this purpose, we map the structure-property-function relationships of nanocellulose-based porous materials and examine the course of actions that are required to translate innovation from the laboratory to industry. Such efforts require attention to regulatory aspects and market pull. Finally, the key challenges and opportunities in this nascent field are critically reviewed.

Sodium Alginate- and Cationic Cellulose-Functionalized Polycaprolactone Nanofibers for In Vitro and Antibacterial Applications

The use of polyelectrolytes is emerging as a fascinating strategy for the functionalization of biomedical membranes, due to their ability to enhance biological responses using the interaction effect of charged groups on multiple interface properties. Herein, two different polyelectrolytes were used to improve the antibacterial properties of polycaprolactone (PCL) nanofibers fabricated via electrospinning. First, a new cationic cellulose derivative, cellulose-bearing imidazolium tosylate (CIMD), was prepared via the nucleophilic substitution of the tosyl group using 1-methylimidazole, as confirmed by NMR analyses, and loaded into the PCL nanofibers. Secondly, sodium alginate (SA) was used to uniformly coat the fibers' surface via self-assembly, as remarked through SEM-EDX analyses. Polyelectrolyte interactions between the CIMD and the SA, initially detected using a FTIR analysis, were confirmed via Z potential measurements: the formation of a CMID/SA complex promoted a substantial charge neutralization of the fibers' surfaces with effects on the physical properties of the membrane in terms of water adsorption and in vitro degradation. Moreover, the presence of SA contributed to the in vitro response of human mesenchymal stem cells (hMSCs), as confirmed by a significant increase in the cells' viability after 7 days in the case of the PCL/CMID/SA complex with respect to the PCL and PCL/CMID membranes. Contrariwise, SA did not nullify the antibacterial effect of CMID, as confirmed by the comparable resistance exhibited by S. mutans, S. aureus, and E. coli to the PCL/CIMD and PCL/CIMD/SA membranes. All the reported results corroborate the idea that the CIMD/SA functionalization of PCL nanofibers has a great potential for the fabrication of efficient antimicrobial membranes for wound healing.

Eco-Friendly Methods for Extraction and Modification of Cellulose: An Overview

Cellulose is the most abundant renewable polymer on Earth and can be obtained from several different sources, such as trees, grass, or biomass residues. However, one of the issues is that not all the fractionation processes are eco-friendly and are essentially based on cooking the lignocellulose feedstock in a harsh chemical mixture, such as NaOH + Na₂S, and water, to break loose fibers. In the last few years, new sustainable fractionation processes have been developed that enable the obtaining of cellulose fibers in a more eco-friendly way. As a raw material, cellulose's use is widely known and established in many areas. Additionally, its products/derivatives are recognized to have a far better environmental impact than fossil-based materials. Examples are textiles and packaging, where forest-based fibers may contribute to renewable and biodegradable substitutes for common synthetic materials and plastics. In this review, some of the main structural characteristics and properties of cellulose, recent green extraction methods/strategies, chemical modification, and applications of cellulose derivatives are discussed.

Cationic dialdehyde cellulose microfibers for efficient removal of eriochrome black T from aqueous solution

Materials based on cellulose have been widely used as a decontaminant agent of wastewater. However, it can not be found in the literature any application of the cationic dialdehyde cellulose (cDAC) in anionic dye removal. Therefore, this study aims a circular economy concept using sugarcane bagasse to obtain a functionalized cellulose by oxidation and cationization. cDAC was characterized by SEM, FT-IR, oxidation degree, and DSC. Adsorption capacity was evaluated by pH, kinetic, concentration effect, strength ionic tests, and recycling. The kinetic followed Elovich model (R² = 0.92605 for EBT = 100 mg/L) and non-linear Langmuir model (R² = 0.94542), which resulted in a maximum adsorption capacity of 563.30 mg/g. The cellulose adsorbent reached an efficient recyclability of 4 cycles. Thus, this work presents a potential material to become a new, clean, low-cost, recyclable, and environmentally friendly alternative for effluent decontamination-containing dyes.

Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment

Cellulose is known to interact well with water, but is insoluble in it. Many polysaccharides such as cellulose are known to have significant hydrogen bond networks joining the molecular chains, and yet they are recalcitrant to aqueous solvents. This review charts the interaction of cellulose with water but with emphasis on the formation of both natural and synthetic fiber composites. Covering studies concerning the interaction of water with wood, the biosynthesis of cellulose in the cell wall, to its dispersion in aqueous suspensions and ultimately in water filtration and fiber-based composite materials this review explores water-cellulose interactions and how they can be exploited for synthetic and natural composites. The suggestion that cellulose is amphiphilic is critically reviewed, with relevance to its processing. Building on this, progress made in using various charged and modified forms of nanocellulose to stabilize oil-water emulsions is addressed. The role of water in the aqueous formation of chiral nematic liquid crystals, and subsequently when dried into composite films is covered. The review will also address the use of cellulose as an aid to water filtration as one area where interactions can be used effectively to prosper human life.

Cationised Fibre-Based Cellulose Multi-Layer Membranes for Sterile and High-Flow Bacteria Retention and Inactivation

Low-cost, readily available, or even disposable membranes in water purification or downstream biopharma processes are becoming attractive alternatives to expensive polymeric columns or filters. In this article, the potential of microfiltration membranes prepared from differently orientated viscose fibre slivers, infused with ultrafine quaternised (qCNF) and amino-hydrophobised (aCNF) cellulose nanofibrils, were investigated for capturing and deactivating the bacteria from water during vacuum filtration. The morphology and capturing mechanism of the single- and multi-layer structured membranes were evaluated using microscopic imaging and colloidal particles. They were assessed for antibacterial efficacy and the retention of selected bacterial species (Escherichia coli, Staphylococcus aureus, Micrococcus luteus), differing in the cell envelope structure, hydrodynamic biovolume (shape and size) and their clustering. The aCNF increased biocidal efficacy significantly when compared to qCNF-integrated membrane, although the latter retained bacteria equally effectively by a thicker multi-layer structured membrane. The retention of bacterial cells occurred through electrostatic and hydrophobic interactions, as well as via interfibrous pore diffusion, depending on their physicochemical properties. For all bacterial strains, the highest retention (up to 100% or log 6 reduction) at >50 L/h∗bar∗m² flow rate was achieved with a 4-layer gradient-structured membrane containing different aCNF content, thereby matching the performance of industrial polymeric filters used for removing bacteria.

Visible light-regulated cationic polymer coupled with photodynamic inactivation as an effective tool for pathogen and biofilm elimination

Background

Pathogenic microorganism pollution has been a challenging public safety issue, attracting considerable scientific interest. A more problematic aspect of this phenomenon is that planktonic bacteria exacerbate biofilm formation. There is an overwhelming demand for developing ultra-efficient, anti-drug resistance, and biocompatibility alternatives to eliminate stubborn pathogenic strains and biofilms.

Results

The present work aims to construct a visible light-induced anti-pathogen agents to ablate biofilms using the complementary merits of ROS and cationic polymers. The photosensitizer chlorin e6-loaded polyethyleneimine-based micelle (Ce6-TPP-PEI) was constructed by an amphiphilic dendritic polymer (TPP-PEI) and physically loaded with photosensitizer chlorin e6. Cationic polymers can promote the interaction between photosensitizer and Gram-negative bacteria, resulting in enhanced targeting of PS and lethality of photodynamic therapy, and remain active for a longer duration to prevent bacterial re-growth when the light is turned off. As expected, an eminent antibacterial effect was observed on the Gram-negative Escherichia coli, which is usually insensitive to photosensitizers. Surprisingly, the cationic polymer and photodynamic combination also exert significant inhibitory and ablative effects on fungi and biofilms. Subsequently, cell hemolysis assessments suggested its good biocompatibility.

Conclusions

Given the above results, the platform developed in this work is an efficient and safe tool for public healthcare and environmental remediation.

Hexavalent Chromium Removal from Industrial Wastewater by Adsorption and Reduction onto Cationic Cellulose Nanocrystals

Cationic cellulose nanocrystals (CCNC) are lignocellulosic bio-nanomaterials that present large, specific areas rich with active surface cationic groups. This study shows the adsorption removal of hexavalent chromium (Cr(VI)) from industrial wastewaters by the CCNC. The CCNC were synthetized through periodate oxidation and Girard's reagent-T cationization. The high value of CCNCs cationic groups and anionic demand reveal probable nanocrystal-Cr(VI) attraction. Adsorption was performed with synthetic Cr(VI) water at different pH, dosage, Cr(VI) concentration and temperature. Fast removal of Cr(VI) was found while operating at pH 3 and 100 mg·L^-1 of dosage. Nevertheless, a first slower complete removal of chromium was achieved by a lower CCNC dosage (40 mg·L^-1). Cr(VI) was fully converted by CCNC into less-toxic trivalent species, kept mainly attached to the material surface. The maximum adsorption capacity was 44 mg·g^-1. Two mechanisms were found for low chromium concentrations (Pseudo-first and pseudo-second kinetic models and continuous growth multi-step intraparticle) and for high concentrations (Elovich model and sequential fast growth-plateau-slow growth intraparticle steps). The Sips model was the best-fitting isotherm. Isotherm thermodynamic analysis indicated a dominant physical sorption. The Arrhenius equation revealed an activation energy between physical and chemical adsorption. CCNC application at selected conditions in industrial wastewater achieved a legal discharge limit of 40 min.

Oil/water separation using elastic bio-aerogels derived from bagasse: Role of fabrication steps

Bio-aerogels hold great promise for selective oil separation from water due to their light weight and high sustainability. However, how the fabrication methods impact the elasticity and oil sorption performance of bio-aerogels still needs systematic comparison and in-depth investigation. In this study, the fabrication of hydrophobic bio-aerogels with good elasticity and reusability was optimized using a factorial design based on the dosages of bagasse-derived cellulose nanofiber, sodium alginate, and calcium carbonate. The role of each key fabrication step, including ice-templating, calcium crosslinking, solvent dehydration, freeze-drying, and silanization, played in the material properties was also elucidated. The optimized bio-aerogels had a low density (7.55 mg/cm³), high porosity (99.47%), large specific surface area (39 m²/g), and strong hydrophobicity (water contact angle of 135°). In addition, the bio-aerogels exhibited outstanding selective oil separation ability towards the oil-water mixture, with oil sorption capacity of 89-126 times its weight. The in-situ calcium crosslinking and solvent dehydration were vital to create porosity and preserve the microstructure of the bio-aerogels. The chemical vapor deposition rendered the bio-aerogels hydrophobic and oleophilic, greatly enhancing the separability of oil from the water-oil mixture.

Assessment of the Performance of Cationic Cellulose Derivatives as Calcium Carbonate Flocculant for Papermaking

Cationic polyacrylamides (CPAMs) are usually used as filler retention agents in papermaking formulations. However, increasing environmental restrictions and their non-renewable origin have driven research into bio-based alternatives. In this context, cationic lignocellulosic derivatives have been attracting considerable research interest as a potential substitute. In this work, distinct cationic celluloses with degrees of substitution of between 0.02 and 1.06 and with distinct morphological properties were synthesized via the cationization of bleached eucalyptus kraft pulp, using a direct cationization with (3-chloro-2-hydroxypropyl) trimethylammonium chloride (CHPTAC) or a two-step cationization, where the cellulose was first oxidized to form dialdehyde cellulose and was then made to react with Girard’s reagent T (GT). Fibrillated samples were produced by subjecting some samples to a high-pressure homogenization treatment. The obtained samples were evaluated regarding their potential to flocculate and retain precipitated calcium carbonate (PCC), and their performance was compared to that of a commercial CPAM. The cationic fibrillated celluloses, with a degree of substitution of ca. 0.13–0.16, exhibited the highest flocculation performance of all the cationic celluloses and were able to increase the filler retention from 43% (with no retention agent) to ca. 61–62% (with the addition of 20 mg/g of PCC). Although it was not possible to achieve the performance of CPAM (filler retention of 73% with an addition of 1 mg/g of PCC), the results demonstrated the potential of cationic cellulose derivatives for use as bio-based retention agents.

Effect of cationization pretreatment on the properties of cationic Eucalyptus micro/nanofibrillated cellulose

Micro/nanofibrillated celluloses (M/NFCs) have attracted considerable research interest over the past few decades, with various pretreatments being used to reduce energy consumption and/or increase fibrillation. To date, few studies have considered cationization as a pretreatment for their preparation. In this work, quaternary ammonium groups were attached to cellulose fibers by a direct reaction with 2,3-epoxypropyltrimethylammonium chloride or by a two-step method (periodate oxidation + Girard's reagent T). The cationic fibers with degrees of substitution (DS) between 0.02 and 0.36, were subjected to homogenization treatment. The morphological properties, chemical composition, and rheological behavior were evaluated to assess the effect of DS and the effect of the cationization method (for samples with similar DS). The two-step cationization resulted in significant degradation of the cellulose structure, leading to the formation of short fibrils and solubilization of the material, ranging from 6% to almost complete solubilization at a DS of 0.36. Direct cationization resulted in longer fibrils with an average diameter of 1 μm, and no significant cellulose degradation was observed, leading to a more cohesive gel-like material (at 1 wt%). These observations clearly show the strong influence of the cationization method on the final properties of the cationic cellulosic materials.

Cellulose Cryogels as Promising Materials for Biomedical Applications

The availability, biocompatibility, non-toxicity, and ease of chemical modification make cellulose a promising natural polymer for the production of biomedical materials. Cryogelation is a relatively new and straightforward technique for producing porous light and super-macroporous cellulose materials. The production stages include dissolution of cellulose in an appropriate solvent, regeneration (coagulation) from the solution, removal of the excessive solvent, and then freezing. Subsequent freeze-drying preserves the micro- and nanostructures of the material formed during the regeneration and freezing steps. Various factors can affect the structure and properties of cellulose cryogels, including the cellulose origin, the dissolution parameters, the solvent type, and the temperature and rate of freezing, as well as the inclusion of different fillers. Adjustment of these parameters can change the morphology and properties of cellulose cryogels to impart the desired characteristics. This review discusses the structure of cellulose and its properties as a biomaterial, the strategies for cellulose dissolution, and the factors affecting the structure and properties of the formed cryogels. We focus on the advantages of the freeze-drying process, highlighting recent studies on the production and application of cellulose cryogels in biomedicine and the main cryogel quality characteristics. Finally, conclusions and prospects are presented regarding the application of cellulose cryogels in wound healing, in the regeneration of various tissues (e.g., damaged cartilage, bone tissue, and nerves), and in controlled-release drug delivery.

Deconstruction and Reassembly of Renewable Polymers and Biocolloids into Next Generation Structured Materials

This review considers the most recent developments in supramolecular and supraparticle structures obtained from natural, renewable biopolymers as well as their disassembly and reassembly into engineered materials. We introduce the main interactions that control bottom-up synthesis and top-down design at different length scales, highlighting the promise of natural biopolymers and associated building blocks. The latter have become main actors in the recent surge of the scientific and patent literature related to the subject. Such developments make prominent use of multicomponent and hierarchical polymeric assemblies and structures that contain polysaccharides (cellulose, chitin, and others), polyphenols (lignins, tannins), and proteins (soy, whey, silk, and other proteins). We offer a comprehensive discussion about the interactions that exist in their native architectures (including multicomponent and composite forms), the chemical modification of polysaccharides and their deconstruction into high axial aspect nanofibers and nanorods. We reflect on the availability and suitability of the latter types of building blocks to enable superstructures and colloidal associations. As far as processing, we describe the most relevant transitions, from the solution to the gel state and the routes that can be used to arrive to consolidated materials with prescribed properties. We highlight the implementation of supramolecular and superstructures in different technological fields that exploit the synergies exhibited by renewable polymers and biocolloids integrated in structured materials.

Recent advancements in cellulose-based biomaterials for management of infected wounds

INTRODUCTION

Chronic wounds are a substantial burden on the healthcare system. Their treatment requires advanced dressings, which can provide a moist wound environment, prevent bacterial infiltration, and act as a drug carrier. Cellulose is biocompatible, biodegradable, and can be functionalized according to specific requirements, which makes it a highly versatile biomaterial. Antimicrobial cellulose dressings are proving to be highly effective against infected wounds.

AREAS COVERED

This review briefly addresses the mechanism of wound healing and its pathophysiology. It also discusses wound infections, biofilm formation, and progressive emergence of drug-resistant bacteria in chronic wounds and the treatment strategies for such types of infected wounds. It also summarizes the general properties, method of production, and types of cellulose wound dressings. It explores recent studies and advancements regarding the use of cellulose and its derivatives in wound management.

EXPERT OPINION

Cellulose and its various functionalized derivatives represent a promising choice of wound dressing material. Cellulose-based dressings loaded with antimicrobials are very useful in controlling infection in a chronic wound. Recent studies showing its efficacy against drug-resistant bacteria make it a favorable choice for chronic wound infections. Further research and large-scale clinical trials are required for better clinical evidence of its efficiency.

Emerging Developments Regarding Nanocellulose-Based Membrane Filtration Material against Microbes

The wide availability and diversity of dangerous microbes poses a considerable problem for health professionals and in the development of new healthcare products. Numerous studies have been conducted to develop membrane filters that have antibacterial properties to solve this problem. Without proper protective filter equipment, healthcare providers, essential workers, and the general public are exposed to the risk of infection. A combination of nanotechnology and biosorption is expected to offer a new and greener approach to improve the usefulness of polysaccharides as an advanced membrane filtration material. Nanocellulose is among the emerging materials of this century and several studies have proven its use in filtering microbes. Its high specific surface area enables the adsorption of various microbial species, and its innate porosity can separate various molecules and retain microbial objects. Besides this, the presence of an abundant OH groups in nanocellulose grants its unique surface modification, which can increase its filtration efficiency through the formation of affinity interactions toward microbes. In this review, an update of the most relevant uses of nanocellulose as a new class of membrane filters against microbes is outlined. Key advancements in surface modifications of nanocellulose to enhance its rejection mechanism are also critically discussed. To the best of our knowledge, this is the first review focusing on the development of nanocellulose as a membrane filter against microbes.

Advancements in release-active antimicrobial biomaterials: A journey from release to relief

Escalating medical expenses due to infectious diseases are causing huge socioeconomic pressure on mankind globally. The emergence of antibiotic resistance has further aggravated this problem. Drug-resistant pathogens are also capable of forming thick biofilms on biotic and abiotic surfaces to thrive in a harsh environment. To address these clinical problems, various strategies including antibacterial agent delivering matrices and bactericidal coatings strategies have been developed. In this review, we have discussed various types of polymeric vehicles such as hydrogels, sponges/cryogels, microgels, nanogels, and meshes, which are commonly used to deliver antibiotics, metal nanoparticles, and biocides. Compositions of these polymeric matrices have been elaborately depicted by elucidating their chemical interactions and potential activity have been discussed. On the other hand, various implant/device-surface coating strategies which exploit the release-active mechanism of bacterial killing are discussed in elaboration. This article is categorized under: Therapeutic Approaches and Drug Discovery > Nanomedicine for Cardiovascular Disease Implantable Materials and Surgical Technologies > Nanomaterials and Implants Therapeutic Approaches and Drug Discovery > Nanomedicine for Infectious Disease.

Ice Templating Soft Matter: Fundamental Principles and Fabrication Approaches to Tailor Pore Structure and Morphology and Their Biomedical Applications

Porous scaffolds are widely used in biomedical applications where pore size and morphology influence a range of biological processes, including mass transfer of solutes, cellular interactions and organization, immune responses, and tissue vascularization, as well as drug delivery from biomaterials. Ice templating, one of the most widely utilized techniques for the fabrication of porous materials, allows control over pore morphology by controlling ice formation in a suspension of solutes. By fine-tuning freezing and solute parameters, ice templating can be used to incorporate pores with tunable morphological features into a wide range of materials using a simple, accessible, and scalable process. While soft matter is widely ice templated for biomedical applications and includes commercial and clinical products, the principles underpinning its ice templating are not reviewed as well as their inorganic counterparts. This review describes and critically evaluates fundamental principles, fabrication and characterization approaches, and biomedical applications of ice templating in polymer-based biomaterials. It describes the utility of porous scaffolds in biomedical applications, highlighting biological mechanisms impacted by pore features, outlines the physical and thermodynamic mechanisms underpinning ice templating, describes common fabrication setups, critically evaluates complexities of ice templating specific to polymers, and discusses future directions in this field.

A Review on the Role and Performance of Cellulose Nanomaterials in Sensors

Sensors and biosensors play a key role as an analytical tool for the rapid, reliable, and early diagnosis of human diseases. Such devices can also be employed for monitoring environmental pollutants in air and water in an expedited way. More recently, nanomaterials have been proposed as an alternative in sensor fabrication to achieve gains in performance in terms of sensitivity, selectivity, and portability. In this direction, the use of cellulose nanomaterials (CNM), such as cellulose nanofibrils (CNF), cellulose nanocrystals (CNC), and bacterial cellulose (BC), has experienced rapid growth in the fabrication of varied types of sensors. The advantageous properties are related to the supramolecular structures that form the distinct CNM, their biocompatibility, and highly reactive functional groups that enable surface functionalization. The CNM can be applied as hydrogels and xerogels, thin films, nanopapers and other structures interesting for sensor design. Besides, CNM can be combined with other materials (e.g., nanoparticles, enzymes, carbon nanomaterials, etc.) and varied substrates to advanced sensors and biosensors fabrication. This review explores recent advances on CNM and composites applied in the fabrication of optical, electrical, electrochemical, and piezoelectric sensors for detecting analytes ranging from environmental pollutants to human physiological parameters. Emphasis is given to how cellulose nanomaterials can contribute to enhance the performance of varied sensors as well as expand novel sensing applications, which could not be easily achieved using standard materials. Finally, challenges and future trends on the use of cellulose-based materials in sensors and biosensors are also discussed.

A Review on Surface-Functionalized Cellulosic Nanostructures as Biocompatible Antibacterial Materials

As the most abundant biopolymer on the earth, cellulose has recently gained significant attention in the development of antibacterial biomaterials. Biodegradability, renewability, strong mechanical properties, tunable aspect ratio, and low density offer tremendous possibilities for the use of cellulose in various fields. Owing to the high number of reactive groups (i.e., hydroxyl groups) on the cellulose surface, it can be readily functionalized with various functional groups, such as aldehydes, carboxylic acids, and amines, leading to diverse properties. In addition, the ease of surface modification of cellulose expands the range of compounds which can be grafted onto its structure, such as proteins, polymers, metal nanoparticles, and antibiotics. There are many studies in which cellulose nano-/microfibrils and nanocrystals are used as a support for antibacterial agents. However, little is known about the relationship between cellulose chemical surface modification and its antibacterial activity or biocompatibility. In this study, we have summarized various techniques for surface modifications of cellulose nanostructures and its derivatives along with their antibacterial and biocompatibility behavior to develop non-leaching and durable antibacterial materials. Despite the high effectiveness of surface-modified cellulosic antibacterial materials, more studies on their mechanism of action, the relationship between their properties and their effectivity, and more in vivo studies are required.