Novel CuCo2O4 Composite Spinel with a Meso-Macroporous Nanosheet Structure for Sulfate Radical Formation and Benzophenone-4 Degradation: Interface Reaction, Degradation Pathway, and DFT Calculation

Synergistic degradation of 2,4-dichlorophenoxyacetic acid in water by interfacial pre-reduction enhanced peroxymonosulfate activation derived from novel zero-valent iron/biochar

Iron-based biochar exhibits great potential in degrading emerging pollutants and remediation of water environments. In this study, a highly efficient catalytic Fe0/biochar (MZB-800) was synthesized by the co-pyrolysis of poplar sawdust and K2FeO4 at 800 °C. A novel water purification technology of pre-reduction followed by PMS activation for MZB-800 was proposed to degrade the refractory 2,4-dichlorophenoxyacetic acid (2,4-D) pesticide. The corrosive effect of the strong oxidizing potassium salt endowed the MZB-800 surface with more Fe0 and porous structure, achieving greater 2,4-D adsorption binding energy. The removal efficiency of MZB-800 on 2,4-D was greater than that of biochar (BC) and conventional Fe0/biochar (Fe-BC) prepared by FeCl3·6 H2O as the precursor. The proposed novel water purification technology showed the synergistic effect between the interfacial pre-reduction and the PMS activation derived by MZB-800. Regarding 2,4-D degradation and dechlorination performance, the synergistic coefficient between pre-reduction and subsequent PMS activation for MZB-800 were 2 and 1.4 respectively. Based on the normalized kinetic analysis and the Langmuir-Hinshelwood model, we proposed the underlying mechanism of MZB-800 interfacial pre-reduction and subsequent PMS activation for synergistic removal of 2,4-D. The large amount of Fe2+ and hydroxyl density accumulated by the Fe0 and hydroquinone structures on the MZB-800 surface during the pre-reduction stage provided abundant active sites for the subsequent activation of PMS. The improved activation reaction rate generated more reactive oxygen species, further strengthening the removal efficiency of 2,4-D. This work manifested that the novel water purification technology of pre-reduction/PMS activation of iron-based biochar is feasible for removing emerging pollutants in the water environment. ENVIRONMENTAL IMPLICATION: Extensive abuse of 2,4-dichlorophenoxyacetic acid (2,4-D) herbicide with high solubility and refractory degradation has caused environmental pollution and ecological deterioration. This manuscript described a novel water purification technology, centered on high-efficiency Fe0/biochar and utilizing pre-reduction and PMS reactivation strategies to synergistically degrade 2,4-D, which had strong environmental relevance. By elucidating the synergistic removal mechanism, the research provided valuable insights into removing emerging pollutants, thus promoting environmental sustainability and safeguarding ecosystem health. Overall, it is of high importance to provide a feasible and efficient method for removing hazardous 2,4-D from water environments, which contributes to addressing pressing environmental problems.

Enhancement of peroxymonosulfate activation with nickel foam-supported CuCo2O4 for tetracycline degradation: Performance and mechanism insights

The modulation of bimetallic oxide structures and development of efficient, easily recoverable catalysts are expected to effectively overcome the limitations associated with powdered catalysts in activating peroxymonosulfate (PMS). In this study, CuCo2O4 was successfully immobilized on the surface of nickel foam (NF) via an electrodeposition-calcination procedure, with highly efficient activation of PMS for tetracycline (TC) degradation (0.55 min-1). Besides acting as a support carrier and providing ample active sites, NF mediated electron transport, prevented the leaching of metal ions and enhanced the efficiency of recycling. Density functional theory (DFT) calculations and experimental tests illustrated that Cu/Co dual-sites can efficiently adsorb PMS, enabling simultaneous reduction and oxidation reactions. The dual-site synergy substantially decreased the adsorption barrier and increased the electron transfer rate. Especially, the Cu+/Cu2+ redox couple acted as an electron donor and facilitated rapid charge transfer, leading to the conversion of Co3+ to Co2+. Moreover, the CuCo2O4@NF + PMS system effectively eliminated TC by employing radical pathways (SO4•-, •OH) and nonradical processes (1O2, e-). Therefore, this study introduces a new approach to overcome the limitations of powdered bimetallic oxides, providing a promising solution for practical applications.

Introducing and Boosting Oxygen Vacancies within CoMn2O4 by Loading on Planar Clay Minerals for Efficient Peroxymonosulfate Activation

CoMn2O4 (CMO) has been recognized as an effective peroxymonosulfate (PMS) activator; however, it still shows disadvantages such as limited reactive sites and metal leakage. Herein, an effective and environmentally friendly composite catalyst, CMO/Kln, was synthesized by anchoring CMO on kaolinite (Kln), a natural clay mineral with a special lamellar structure, to activate peroxymonosulfate (PMS) for the degradation of residue pharmaceuticals in water. The abundant hydroxyl groups located on the surface of Kln helped induce rich oxygen vacancies (OVs) into composite CMO/Kln, which not only acted as additional active sites but also accelerated working efficiency. In addition, compared with bare CMO, CMO/Kln showed lower crystallinity, and the adoption of the Kln substrate contributed to its structural stability with lower metal leaching after three rounds of reaction. The universal applicability of CMO/Kln was also verified by using three other pharmaceuticals as probes. This work shed light on the adoption of natural clay minerals in modifying CMO catalysts with promoted catalytic activity for the efficient and eco-friendly remediation of pharmaceuticals in wastewater.

Contribution of 1O2 in the efficient degradation of organic pollutants with Cu0/Cu2O/CuO@N-C activated peroxymonosulfate: A Case study with tetracycline

Peroxymonosulfate-mediated advanced oxidation processes (PMS-AOPs) degrading organic pollutants (Tetracycline (TC) as an example) in water with singlet oxygen (1O2) as the main reactive oxygen has received more and more attention. However, the generation mechanism of 1O2 is still unclear. Consequently, this study investigates the 1O2 formation mechanism during the activated PMS process using a nitrogen-copper-loaded carbon-based material (Cu0/Cu2O/CuO@N-C), synthesized by thermally decomposing organobase-modified HKUST-1 via a one-pot method. It was discovered that incorporating an organobase (Benzylamine) into the metal organic framework (MOF) precursor directs the MOF's self-assembly process and supplements its nitrogen content. This modification modulates the Nx-Cu-Oy active site formation in the material, selectively producing 1O2. Additionally, 1O2 was identified as the dominant reactive oxygen species in the Cu0/Cu2O/CuO@N-C-PMS system, contributing to TC degradation with a rate of 70.82%. The TC degradation efficiency remained high in the pH range of 3-11 and sustained its efficacy after five consecutive uses. Finally, based on the intermediates of TC degradation, three possible degradation pathways were postulated, and a reduction in the ecotoxicity of the degradation products was predicted. This work presents a novel and general strategy for constructing nitrogen-copper-loaded carbon-based materials for use in PMS-AOPs.

Metal-organic frameworks-derived MCo2O4 (M = Zn, Ni, Cu) two-dimensional nanosheets as anodes materials to boost lithium storage

Transition metal oxides (TMOs) have received significant consideration. Because of their enormous theoretical capacity, cheap, and less toxicity. Notably, cobalt-based materials hold promises as negative electrode materials for batteries, but they suffer from less electrical conductivity and significant volume changes during operation. In order to address these challenges, sacrificial templating techniques at the nanoscale offer a potential solution for improving the electrochemical stability and rate performance of these materials. More specifically, these tactics have proven popular for designing Li-ion storages. To ascertain the impact of multiple metal ions on the electrochemical capacity, metal organic frameworks (MOFs) derived MCo2O4-MOF (M = Zn, Ni, Cu) were developed. Among these, ZnCo2O4 showed the best electrochemical performance (927.2 mAh g-1 at 0.1 A g-1 after 250 cycles). Furthermore, calculations based on density functional theory (DFT) revealed that ZnCo2O4 had the lowest Li+ adsorption energy, with a minimum value of -1.61 eV. Moreover, this research aims to design controllable nanostructures in order to enhance the design of transition bimetallic oxide composites for energy storage applications.

The environmental sources of benzophenones: Distribution, pretreatment, analysis and removal techniques

Benzophenones (BPs) have wide practical applications in real human life due to its presence in personal care products, UV-filters, drugs, food packaging bags, etc. It enters the wastewater by daily routine activities such as showering, impacting the whole aquatic system, then posing a threat to human health. Due to this fact, the monitoring and removal of BPs in the environment is quite important. In the past decade, various novel analytical and removal techniques have been developed for the determination of BPs in environmental samples including wastewater, municipal landfill leachate, sewage sludge, and aquatic plants. This review provides a critical summary and comparison of the available cutting-edge pretreatment, determination and removal techniques of BPs in environment. It also focuses on novel materials and techniques in keeping with the concept of "green chemistry", and describes on challenges associated with the analysis of BPs, removal technologies, suggesting future development strategies.

Efficient Fenton-like degradation of tetracycline by stalactite-like CuCo-LDO/CN catalysts: The overlooked contribution of dissolved oxygen

In the Fenton-like processes, the resources that exist in the system itself (e.g., dissolved oxygen, electron-rich pollutants) are often overlooked. Herein, a novel CuCo-LDO/CN composite catalyst with a strong "metal-π" effect was fabricated by in situ calcination which could activate dissolved oxygen to generate active oxygen species and degrade the electron-rich pollutants directly. The CuCo-LDO/CN (1:10) with the largest specific surface aera, most C-O-M bonds and least oxygen vacancies exhibited the best catalytic performance for tetracycline (TC)degradation (TC removal efficiency 93.2% and mineralization efficiency 40%, respectively, after 40 min at neutral pH) compared to CuCo-LDO and other CuCo-LDO/CN composite catalysts. In the absence of H2O2, dissolved oxygen could be activated by the catalyst to generate O2·-and ·OH, which contributed to approximately 20.7% of TC degradation, providing a faster and cost-effective way for TC removal from wastewater. While in the presence of H2O2, it was activated by CuCo-LDO/CN to generate·OH as the dominant reactive oxygen species and meanwhile TC transferred electrons to H2O2 through C-O-M bonds, accelerating the Cu+/Cu2+ and Co2+/Co3+ redox cycles. The possible degradation pathways of TC were proposed, and the environmental hazard of TC is greatly mitigated according to toxicity prediction.

Efficient degradation of benzalkonium chloride by FeMn-CA300 catalyst activated persulfate process: Surface hydroxyl potentiation mechanism and degradation pathway

The consumption of disinfectants increased dramatically with the outbreak of the COVID-19 epidemic. Benzalkonium chloride (DDBAC), a cationic surfactant disinfectant for import and export cargoes, is used for effective degradation method. For DDBAC effective degradation, polyhedral Fe-Mn bimetallic catalyst of Prussian blue analogue (FeMn-CA300) was novelty developed for rapid peroxymonosulfate (PMS) activation. Results showed that the Fe/Mn redox and surface hydroxyl groups in the catalyst played an important role in the DDBAC-enhanced degradation. The removal effectiveness of 10 mg L-1 DDBAC was up to 99.4% in 80 min under the initial pH = 7, catalyst dosage of 0.4 g L-1, and PMS concentration of 15 mmol L-1. In addition, FeMn-CA300 had a wide pH applicability range. The results indicated that hydroxyls, sulfate radicals, and singlet oxygen could effectively improve the degradation efficiency, where sulfate radicals played a crucial role. Finally, the corresponding degradation path of DDBAC was further provided according to GC-MS results. The results of this study provide new insights into the degradation of DDBAC, thereby highlighting the great potential of FeMnca300/PMS to control refractory organic compounds in the aqueous phase.

Molecular structure-dependent contribution of reactive species to organic pollutant degradation using nanosheet Bi2Fe4O9 activated peroxymonosulfate

Iron-based catalysts have attracted increasing attention in heterogeneous activation of peroxymonosulfate (PMS). However, the activity of most iron-based heterogenous catalysts is not satisfactory for practical application and the proposed activation mechanisms of PMS by iron-based heterogenous catalyst vary case by case. This study prepared Bi₂Fe₄O₉ (BFO) nanosheet with super high activity toward PMS, which was comparable to its homogeneous counterpart at pH 3.0 and superior to its homogeneous counterpart at pH 7.0. Fe sites, lattice oxygen and oxygen vacancies on BFO surface were believed to be involved in the activation of PMS. By using electron paramagnetic resonance (EPR), radical scavenging tests, ⁵⁷Fe Mössbauer and ¹⁸O isotope-labeling technique, the generation of reactive species including sulfate radicals, hydroxyl radicals, superoxide and Fe (IV) were confirmed in BFO/PMS system. However, the contribution of reactive species to the elimination of organic pollutants very much depends on their molecular structure. The effect of water matrices on the elimination of organic pollutants also hinges on their molecular structure. This study implies that the molecular structure of organic pollutants governs their oxidation mechanism and their fate in iron-based heterogeneous Fenton-like system and further broadens our knowledge on the activation mechanism of PMS by iron-based heterogeneous catalyst.

Proton transfer triggered in-situ construction of C=N active site to activate PMS for efficient autocatalytic degradation of low-carbon fatty amine

Removal of low-carbon fatty amines (LCFAs) in wastewater treatment poses a significant technical challenge due to their small molecular size, high polarity, high bond dissociation energy, electron deficiency, and poor biodegradability. Moreover, their low Brønsted acidity deteriorates this issue. To address this problem, we have developed a novel base-induced autocatalytic technique for the highly efficient removal of a model pollutant, dimethylamine (DMA), in a homogeneous peroxymonosulfate (PMS) system. A high reaction rate constant of 0.32 min^-1 and almost complete removal of DMA within 12 min are achieved. Multi-scaled characterizations and theoretical calculations reveal that the in situ constructed C=N bond as the crucial active site activates PMS to produce abundant ¹O₂. Subsequently, ¹O₂ oxidizes DMA through multiple H-abstractions, accompanied by the generation of another C=N structure, thus achieving the autocatalytic cycle of pollutant. During this process, base-induced proton transfers of pollutant and oxidant are essential prerequisites for C=N fabrication. A relevant mechanism of autocatalytic degradation is unraveled and further supported by DFT calculations at the molecular level. Various assessments indicate that this self-catalytic technique exhibits a reduced toxicity and volatility process, and a low treatment cost (0.47 $/m³). This technology has strong environmental tolerance, especially for the high concentrations of chlorine ion (1775 ppm) and humic acid (50 ppm). Moreover, it not only exhibits excellent degradation performance for different amine organics but also for the coexisting common pollutants including ofloxacin, phenol, and sulforaphane. These results fully demonstrate the superiority of the proposed strategy for practical application in wastewater treatment. Overall, this autocatalysis technology based on the in-situ construction of metal-free active site by regulating proton transfer will provide a brand-new strategy for environmental remediation.

Construction of Cu7 S4 @CuCo2 O4 Yolk-Shell Microspheres Composite and Elucidation of Its Enhanced Photocatalytic Activity, Mechanism, and Pathway for Carbamazepine Degradation

Water pollution caused by the massive use of medicines has caused significant environmental problems. This work first reports the synthesis and characterization of the Cu₇ S₄ /CuCo₂ O₄ (CS/CCO) yolk-shell microspheres via hydrothermal and annealing methods, and then investigates their photocatalytic performance in removing organic water pollutants. The 10-CS/CCO composite with yolk-shell microspheres exhibits the highest photodegradation rate of carbamazepine (CBZ), reaching 96.3% within 2 h. The 10-CS/CCO also demonstrates more than two times higher photodegradation rates than the pure (Cu₇ S₄ ) CS and (CuCo₂ O₄ ) CCO. This outstanding photocatalytic performance can be attributed to the unique yolk-shell structure and the Z-scheme charge transfer pathway, reducing multiple reflections of the acting light. These factors enhance the light absorption efficiency and efficiently transfer photoexcited charge carriers. In-depth, photocatalytic degradation pathways of CBZ are systematically evaluated via the identification of degradation intermediates with Fukui index calculation. The insights gained from this work can serve as a guideline for developing low-cost and efficient Z-scheme photocatalyst composites with the yolk-shell structure.

Electron-transfer pathways insights into contaminants oxidized by Cu-OOSO3- intermediate: Effects of oxidation states of Cu and solution pH values

The copper-peroxy complex (Cu-OOSO₃^-) metastable intermediate has been confirmed to oxidize contaminants via a single-electron-transfer pathway or an oxygen-atom-transfer pathway. And the effects of Cu oxidation states and reaction pH conditions on the intermediate properties have not been explored in depth. Here, copper oxide (CuO_x) catalysts with different Cu oxidation states were synthesized by a simple precipitation method by controlling the reaction temperature from 0 to 45 °C. CuO_x displayed a strong catalytic dependence on the Cu oxidation state, and CuO_x-30 with Cu average valence on the catalyst surface of 1.61 was more reactive for catalytic degradation of bisphenol A with peroxymonosulfate (PMS). Notably, CuO_x-30, with the best electron-accepting ability, was easier to bonding with PMS to form the Cu-OOSO₃^- reactive complex, and the generated intermediate exhibited the strongest capacity to obtain electrons from contaminants. Moreover, the electron-transfer pathways were closely related to the average valence of Cu, and the contribution of the oxygen-atom-transfer pathway changed volcanic with increasing Cu valence. Meanwhile, the reaction predominantly involved the oxygen-atom-transfer pathway under acidic conditions (pH=3), while the contribution of the single-electron-transfer pathway raised with increasing pH values. Hence, this work was devoted to providing new insights into the CuO_x-inducing PMS activation and vital supplementary to the properties of the Cu-OOSO₃^- intermediate.

Selective and efficient removal of emerging contaminants by sponge-like manganese ferrite synthesized using a solvent-free method: Crucial role of the three-dimensional porous structure

Ubiquitous macromolecular natural organic matter (NOM) in wastewater seriously influences the removal of emerging small-molecule contaminants via heterogeneous advanced oxidation processes because this material covers active sites and quenches reactive oxygen species. Here, sponge-like magnetic manganese ferrite (MnFe₂O₄-S) with a three-dimensional hierarchical porous structure was prepared via a facile solvent-free molten method. Compared with the particle-like structure of MnFe₂O₄-P, the sponge-like structure of MnFe₂O₄-S presents an enlarged specific surface area (112.14 m²·g^-1 vs. 58.73 m²·g^-1) and a smaller macropore diameter (68.2-77.2 nm vs. 946.5 nm). Enlarging the specific surface area increases the exposure of active sites, and adjusting the pore size helps sieve NOM and emerging contaminants. These changes are expected to effectively improve the degradation activity and overcome interference. To confirm the superiority of the sponge-like structure, MnFe₂O₄-S was used to activate peroxymonosulfate (PMS) for the degradation of multiple emerging contaminants, and its ability to degrade bisphenol A with and without humic acid (HA) was compared with that of MnFe₂O₄-P. The degradation activity of MnFe₂O₄-S was 1.6 times greater than that of MnFe₂O₄-P. Moreover, 20 mg·L^-1 HA inhibited the degradation activity of MnFe₂O₄-S by only 7.1%, which was much lower than that obtained for MnFe₂O₄-P (53.4%). In addition, the excellent performance was maintained in multiple water matrices. Notably, under lake water matrices, the degradation activity of MnFe₂O₄-P was inhibited by 35.6% while that of MnFe₂O₄-S was hardly inhibited. More importantly, the MnFe₂O₄-S/PMS system was also applicable to the treatment of actual wastewater and 73.0% and 90.1% of total organic carbon and chemical oxygen demand was removed from bio-treated coking wastewater containing non-biodegradable contaminants and NOM. This study provides an alternative route for the green production of high-activity porous spinel ferrites with environmental anti-interference properties.

Rod-Like Nanostructured Cu-Co Spinel with Rich Oxygen Vacancies for Efficient Electrocatalytic Dechlorination

Dichloromethane (CH₂Cl₂) hydrodechlorination to methane (CH₄) is a promising approach to remove the halogenated contaminants and generate clean energy. In this work, rod-like nanostructured CuCo₂O₄ spinels with rich oxygen vacancies are designed for highly efficient electrochemical reduction dechlorination of dichloromethane. Microscopy characterizations revealed that the special rod-like nanostructure and rich oxygen vacancies can efficiently enhance surface area, electronic/ionic transport, and expose more active sites. The experimental tests demonstrated that CuCo₂O₄-3 with rod-like nanostructures outperformed other morphology of CuCo₂O₄ spinel nanostructures in catalytic activity and product selectivity. The highest methane production of 148.84 μmol in 4 h with a Faradaic efficiency of 21.61% at -2.94 V (vs SCE) is shown. Furthermore, the density function theory proved oxygen vacancies significantly decreased the energy barrier to promote the catalyst in the reaction and O_v-Cu was the main active site in dichloromethane hydrodechlorination. This work explores a promising way to synthesize the highly efficient electrocatalysts, which may be an effective catalyst for dichloromethane hydrodechlorination to methane.

Carbon-doped defect MoS2 co-catalytic Fe3+/peroxymonosulfate process for efficient sulfadiazine degradation: Accelerating Fe3+/Fe2+ cycle and 1O2 dominated oxidation

In order to accelerate Fe³⁺/Fe²⁺ cycle and boost singlet oxygen (¹O₂) generation in peroxymonosulfate (PMS) Fenton-like system, a co-catalyst of defect MoS₂ was prepared by C doping and C2-MoS₂/Fe³⁺/PMS system was structured. The removal efficiency of sulfadiazine (SDZ) antibiotics was nearly 100 % in 10 min in the system under the appropriate conditions ([co-catalysts] = 0.2 g/L, [PMS] = 0.1 mM, [Fe³⁺] = 0.4 mM, pH 3.5), and the reaction rate constant was 4.6 times that of Fe³⁺/PMS system. C doping MoS₂ could induce phase transition, yield more sulfur defects, and expedite electron transfer. Besides, exposed Mo⁴⁺ sites on C2-MoS₂ could significantly enhance the regeneration and stability of Fe²⁺ and further promote the activation of PMS. ·OH, SO₄·^-, and ¹O₂ were responsible for SDZ degradation in the system. Notably, ¹O₂ generation was efficiently promoted by sulfur defects and CO sites on C2-MoS₂, and ¹O₂ played the main role in SDZ degradation. Therefore, this co-catalytic system exhibited great anti-interference and stability, and organic contaminants could be efficiently and stably degraded in a 14-day long-term experiment. This work provides a new approach for improving the co-catalytic performance of MoS₂ for Fe³⁺ mediated Fenton-like technology, and offers a promising antibiotic pollutant removal strategy.

Development of Quinary Layered Double Hydroxide-Derived High-Entropy Oxides for Toluene Catalytic Removal

In this work, a novel method for the preparation of high-entropy oxides (HEO) was successfully developed using multivariate composition layered double hydroxides (LDHs) as precursor. Thermal treatment over 600 °C led to the complete transformation of LDHs to single spinel phase HEOs. The performance of the obtained HEO catalysts in the removal of volatile organic compounds (VOCs) was studied with the catalytic oxidation of toluene as the probe reaction. The optimized HEO-600 catalyst showed impressive activity and stability over toluene catalytic oxidation, which resulted from the vast quantity of surface oxygen vacancies and the relative variable metal valence. The T50 and T90 values of HEO-600 were 246 and 254 °C, and the T90 value only presented a slight increase to 265 °C after a 10-cycle test. This work developed a simple way to obtain HEO materials and provide technical support for the application of HEO catalysts for VOCs removal.

Multimetallic CuCoNi Oxide Nanowires In Situ Grown on a Nickel Foam Substrate Catalyze Persulfate Activation via Mediating Electron Transfer

In situ growth of nanostructures on substrates is a strategy for designing highly efficient catalytic materials. Herein, multimetallic CuCoNi oxide nanowires are synthesized in situ on a three-dimensional nickel foam (NF) substrate (CuCoNi-NF) by a hydrothermal method and applied to peroxydisulfate (PDS) activation as immobilized catalysts. The catalytic performance of CuCoNi-NF is evaluated through the degradation of organic pollutants such as bisphenol A (BPA) and practical wastewater. The results indicate that the NF not only plays an important role as the substrate support but also serves as an internal Ni source for material fabrication. CuCoNi-NF exhibits high activity and stability during PDS activation as it mediates electron transfer from BPA to PDS. CuCoNi-NF first donates electrons to PDS to arrive at an oxidized state and subsequently deprives electrons from BPA to return to the initial state. CuCoNi-NF maintains high catalytic activity in the pH range of 5.2-9.2, adapts to a high ionic strength up to 100 mM, and resists background HCO₃^- and humic acid. Meanwhile, 76.6% of the total organic carbon can be removed from packaging wastewater by CuCoNi-NF-catalyzed PDS activation. This immobilized catalyst shows promising potential in wastewater treatment, well addressing the separation and recovery of conventional powdered catalysts.

Controlling oxygen vacancies of CoMn2O4 by loading on planar and tubular clay minerals and its application for boosted PMS activation

A representative transition metal oxide (TMO), CoMn₂O₄ (CMO), is recognized as an effective peroxymonosulfate (PMS) activator with disadvantages like limited reactive sites and metal leakage. Herein, novel catalysts were synthesized by anchoring CMO on kaolinite (Kln) and halloysite (Hal) matrixes, two natural clay minerals with lamellar and tubular structures, for PMS activation in pharmaceutical degradation. Hal and Kln helped to control the crystallinity of CMO spontaneously with induce oxygen vacancies (OVs), which significantly enhanced the working efficiency. The reaction rate constants of Hal/CMO and Kln/CMO towards OFX degradation were nearly triple and twice that of bare CMO, respectively, with a 60% decrease in metal usage. The formation of OVs provided additional active sites for the reaction and accelerated the electron transfer. CMO/Hal and CMO/Kln exhibited better stability and durability than CMO, while CMO/Kln showed higher structural stability with lower metal leaching after 3 rounds of reaction. The higher crystallinity of CMO/Kln resulted in less OVs, but higher structural stability. The universal applicability of CMO/Hal and CMO/Kln were verified by using three other pharmaceuticals as probes. This work shed light on the modification of TMO catalysts by introducing clay mineral substrates for the efficient and ecofriendly remediation of pharmaceuticals in wastewater.

Selenization governs the intrinsic activity of copper-cobalt complexes for enhanced non-radical Fenton-like oxidation toward organic contaminants

Non-radical oxidation pathways in the Fenton-like process have a superior catalytic activity for the selective degradation of organic contaminants under complicated water matrices. Whereas the synthesis of high-performance catalysts and research on reaction mechanisms are unsatisfactory. Herein, it was the first report on copper-cobalt selenide (CuCoSe) that was well-prepared to activate hydrogen peroxide (H₂O₂) for non-radical species generation. The optimized CuCoSe+H₂O₂ system achieved excellent removal of chlortetracycline (CTC) in 10 min at neutral pH along with pleasing reusability and stability. Moreover, it exhibited great anti-interference capacity to inorganic anions and natural organic matters even in actual applications. Multi-surveys verified that singlet oxygen (¹O₂) was the dominant active species in this reaction and electron transfer on the surface-bound of CuCoSe and H₂O₂ likewise played an important role in direct CTC oxidation. Where the synergetic metals of Cu and Co accounted for the active sites, and the introduced Se atoms accelerated the circulation efficiency of Co³⁺/Co²⁺, Cu²⁺/Cu⁺ and Cu²⁺/Co²⁺. Simultaneously, the produced Se/O vacancies further facilitated electron mediation to enhance non-radical behaviors. With the aid of intermediate identification and theoretical calculation, the degradation pathways of CTC were proposed. And the predicted ecotoxicity indicated a decrease in underlying environmental risk.

Enhanced Degradation of Rhodamine B through Peroxymonosulfate Activated by a Metal Oxide/Carbon Nitride Composite

The development of high catalytic performance heterogeneous catalysts such as peroxymonosulfate (PMS) activators is important for the practical remediation of organic pollution caused by Rhodamine B (RhB). An economical and facile synthesized composite of copper–magnesium oxide and carbon nitride (CM/g-C3N4) was prepared by the sol-gel/high-temperature pyrolysis method to activate PMS for RhB degradation. CM/g-C3N4 exhibited a splendid structure for PMS activation, and the aggregation of copper–magnesium oxide was decreased when it was combined with carbon nitride. The introduction of magnesium oxide and carbon nitride increased the specific surface area and pore volume of CM/g-C3N4, providing more reaction sites. The low usage of CM/g-C3N4 (0.3 g/L) and PMS (1.0 mM) could rapidly degrade 99.88% of 10 mg/L RhB, and the RhB removal efficiency maintained 99.30% after five cycles, showing the superior catalytic performance and reusability of CM/g-C3N4. The synergistic effect of copper and g-C3N4 improved the PMS activation. According to the analyses of EPR and quenching experiments, SO4•−, •OH and O2•− radicals and 1O2 were generated in the activation of PMS, of which SO4•− and 1O2 were important for RhB removal. The toxicity of RhB was alleviated after being degraded by the CM/g-C3N4/PMS system. This study provides an efficient and promising strategy for removing dyes in water due to the hybrid reaction pathways in the CM/g-C3N4/PMS system.

Origin of the Excellent Activity and Selectivity of a Single-Atom Copper Catalyst with Unsaturated Cu-N2 Sites via Peroxydisulfate Activation: Cu(III) as a Dominant Oxidizing Species

As an efficient active oxidant for the selective degradation of pollutants in wastewater, the high-valent copper species Cu(III) with persulfate activation has attracted substantial attention in some Cu-based catalysts. However, the systematic study of a catalyst structure and mechanism about Cu(III) with peroxydisulfate (PDS) activation is challenging owing to the coexistence of multiple Cu species and the structural symmetry of PDS. Herein, we anchored a Cu atom with two pyridinic N atoms to synthesize a single-atom Cu catalyst (Cu_SA-NC). Experimental characterizations and theoretical calculations complemented each other well because of the uniform atomic active sites. The single-atom Cu was identified as the active site, and the unsaturated Cu-N₂ configuration was more conductive to PDS activation than the saturated Cu-N₄ configuration. Benefiting from the generation of Cu(III), Cu_SA-NC exhibited an obvious selective and anti-interference performance for pollutant degradation in a complex matrix. The superior catalytic activity of Cu_SA-NC compared with that of other reported Cu-based catalysts and good durability in a continuous-flow experiment further revealed the potential of Cu_SA-NC for practical applications. This work strongly deepens the understanding of the generation of Cu(III) in a single-atom Cu catalyst with unsaturated Cu-N₂ sites under PDS activation and develops an efficient approach for actual water purification.

Sustainably recycling spent lithium-ion batteries to prepare magnetically separable cobalt ferrite for catalytic degradation of bisphenol A via peroxymonosulfate activation

A selective separation-recovery process based on tuning organic acid was proposed to the resource recycling of spent lithium-ion batteries (LIBs) for the first time. The low-cost preparation of CoFe₂O₄, reuse of waste acid and recovery of Li can be realized in this process, simultaneously. Li and Co in spent LIBs can be leached efficiently using citric acid as a leaching agent, and separated effectively from leaching solution by tuning oxalic acid content. The results from the characterizations of the prepared CoFe₂O₄ (CoFe₂O₄-LIBs) show that it possesses higher ratio of Co(II)/Co(III) and Fe(II)/Fe(III), larger surface specific area and more number of acid sites in comparison with pure CoFe₂O₄. Besides, CoFe₂O₄-LIBs was used to activate peroxymonosulfate (PMS) for the degradation of bisphenol A (BPA). Interestingly, its degradation performance is superior to that of pure CoFe₂O₄ and the related Co-based catalysts. The excellent degradation performance can be maintained in presence of inorganic ions (e.g., Cl^-, HCO₃^-, H₂PO₄^- and NO₃^-) with high concentration or humic acid. Moreover, surface-bound SO₄^∙- is considered as the main reactive species for the degradation of BPA. More importantly, CoFe₂O₄-LIBs can be readily recycled by using an external magnet and own superior ability of regeneration.

Porous P, Fe-doped g-C3N4 nanostructure with enhanced photo-Fenton activity for removal of tetracycline hydrochloride: Mechanism insight, DFT calculation and degradation pathways

This study fabricated an efficient P and Fe co-doping graphitic carbon nitride catalyst (Fe- CN/P) by thermal polymerization of melamine, FeCl₃, and 2-hydroxyphosphonoacetic acid (HPAA) mixture. The Fe-CN/P catalyst exhibited much better tetracycline hydrochloride (TCH) degradation performance than that of single doping and neat CN. Various characterizations indicated that the introduction of HPAA significantly increased the specific surface area of CN and improved charge separation as well as transfer efficiency. Based on Fe 2p XPS analysis and indirect determination of hydroxyl radical (·OH) content, the separated photogenerated electrons accelerated the reduction of Fe(III) and activated photo-Fenton reaction, resulting in more ·OH species generation. The effect of pH value, catalyst dosages, H₂O₂ concentration, the type of cations and anions as well as water matrices on the degradation of TCH by Fe-CN/P was systematically investigated. The main degradation pathways of TCH were proposed according to the LC-MS intermediates detection and DFT calculation. The results indicated that reactive oxide species (ROS) were more likely to attack the atoms with high Fukui index (f⁰). This work provides new ideas for adjusting the morphology and electronic structure of CN to enhance its photo-Fenton catalytic activity.

Encapsulation of spinel CuCo2O4 hollow sphere in V2O5-decorated graphitic carbon nitride as high-efficiency double Z-type nanocomposite for levofloxacin photodegradation

In this study, spinel CuCo₂O₄ (CCO) with a hierarchical hollow sphere morphology was encapsulated in V₂O₅-decorated ultra-wrinkled graphitic carbon-nitride (VO-UCN) for the first time via a facile glycerol-assisted solvothermal method in the interest of developing a novel high-efficiency double Z-type nano-photocatalyst (denoted as VO-UCN@CCO). The remarkable physicochemical features of the as-prepared nano-photocatalysts were verified using diverse characterization techniques including TGA, XRD, FT-IR, FE-SEM, TEM, BET, UV-vis DRS, PL, EIS, and transient photocurrent techniques. Herein, VO-UCN@CCO nanocomposite was employed for the photodisintegration of levofloxacin (LVOF) antibiotic under visible-light irradiation and the impact of certain operative reaction system variables was explored in an effort to optimize the photocatalytic capability. The 40% loading of CCO in VO-UCN@CCO nanocomposite was found to display maximum photocatalytic performance (about 95%) for LVOF photodecomposition, which was 9.3, 6.6, and 13.8 times greater when compared with pristine VO, UCN, and CCO, respectively. A high capability was observed for as-prepared photocatalyst during reusability tests and near 90% degradation efficiency was obtained in the sixth run. The complete mineralization of LVOF was achieved by the VO-UCN@CCO photocatalyst process after 300 min of reaction. An excellent synergy factor towards the degradation of LVOF was obtained for VO-UCN@CCO compared to each of its components alone. This peculiar design is envisaged to provide new inspirations for ameliorating the photocatalytic decontamination of tenacious and non-biodegradable species present in real wastewater.

Rice husk biochar modified-CuCo2O4 as an efficient peroxymonosulfate activator for non-radical degradation of organic pollutants from aqueous environment

A series of rice husk biochar (RHBC) modified bimetallic oxides were prepared using a simple pyrolysis method to activate peroxymonosulfate (PMS) for the degradation of acid orange G (OG). The results demonstrated that 50 mg L⁻¹ OG was completely decomposed by 1 mM PMS activated with 100 mg L⁻¹ RHBC–CuCo₂O₄ within 15 min at initial pH 3.4. The OG degradation rate constant k of RHBC–CuCo₂O₄/PMS (0.95 × 10⁻¹ min⁻¹) was five times greater than that of CuCo₂O₄/PMS (0.19 × 10⁻¹ min⁻¹), suggesting that the introduction of RHBC significantly improved the activity of bimetallic oxides. The effects of the initial pH, catalyst dosage, PMS concentration and reaction temperature on OG removal were also studied. The degradation products of OG were analysed using a gas chromatography-mass spectrometer (GC-MS). Electron paramagnetic resonance (EPR) and quenching experiments showed that singlet oxygen (¹O₂) was the main active species. The RHBC–CuCo₂O₄/PMS oxidation system is not only unaffected by inorganic anions (Cl⁻, NO₃⁻, HCO₃⁻) and humic acid (HA), but also could remove other typical pollutants of acetaminophen (ACT), sulfathiazole (STZ), rhodamine B (RhB), and bisphenol A (BPA). These findings show that RHBC–CuCo₂O₄ has great potential for practical applications in the removal of typical organic pollutants.

A series of rice husk biochar (RHBC) modified bimetallic oxides were prepared using a simple pyrolysis method to activate peroxymonosulfate (PMS) for the degradation of acid orange G (OG).

Boosting the activation of molecular oxygen and the degradation of tetracycline over high loading Ag single atomic catalyst

Photocatalytic activation of molecular oxygen (O₂) is a promising way in oxidative degradation of organic pollutants. However, it suffers from low efficiency mainly due to the limited active sites for O₂ activation over traditional photocatalysts. Therefore, we established a single atomic Ag-g-C₃N₄ (SAACN) catalyst with 10 wt% loading of Ag single sites for boosting the O₂ activation during the degradation of tetracycline (TC), and 10 wt% loading of nanoparticle Ag-g-C₃N₄ (NPACN) was studied as a comparison. When using SAACN, the accumulative concentration of superoxide (•O₂^-), hydroxyl radical (•OH), singlet oxygen (¹O₂) reached up to 0.66, 0.19, 0.33 mmol L^-1h^-1, respectively, within 120 min, 11.7, 5.7 and 4.9 times compared with those using NPACN, representing 17.24% of dissolved O₂ was converted to reactive oxygen species (ROS). When additionally feeding air or O_2, the accumulative concentrations of •O₂^-, •OH, ¹O₂ were even higher (air: 4.21, 0.97, 2.02 mmol L^-1 h^-1; O₂: 17.13, 1.32, 9.00 mmol L^-1 h^-1). The rate constants (k) for degrading the TC were 0.0409 min^-1 over SAACN and 0.00880 min^-1 over NPACN, respectively (mineralization rate: 95.7% vs. 59.9% after 3 h of degradation). Moreover, the degradation ability of SAACN did not decrease in a wide range of pH value (4-10) or under low temperature (10 °C). Besides the high exposure of Ag single sites, other advances of SAACN were: 1(O₂ was more energetic favorable to adsorb on single atomic Ag sites; 2) Positive Ag single sites were easier to obtain the electrons from the surrounding N atoms, and facilitated electron transfer towards adsorbed O₂.

Recent advances in cobalt-activated sulfate radical-based advanced oxidation processes for water remediation: A review

Sulfate radical-based advanced oxidation processes (SR-AOPs) have attracted increasing attention for the degradation of organic contaminants in water. The oxidants of SR-AOPs could be activated to generate different kinds of reactive oxygen species (ROS, e.g., hydroxyl radicals (OH), sulfate radicals (SO₄^-), singlet oxygen (¹O₂), and superoxide radicals (O₂^-)) by various catalysts. As one of the promising catalysts, cobalt-based catalysts have been extensively investigated in catalytic activity and stability during water remediation. This article mainly summarizes recent advances in preparation and applications of cobalt-based catalysts on peroxydisulfate (PDS)/peroxymonosulfate (PMS) activation since 2016. The review covers the development of homogeneous cobalt ions, cobalt oxides, supported cobalt composites, and cobalt-based mixed metal oxides for PDS/PMS activation, especially for the latest nanocomposites such as cobalt-based metal-organic frameworks and single-atom catalysts. This article also discussed the activation mechanisms and the influencing factors of different cobalt-based catalysts for activating PDS/PMS. Finally, the future perspectives on the challenges and applications of cobalt-based catalysts are presented at the end of this paper.

Surface dual redox cycles of Mn(III)/Mn(IV) and Cu(I)/Cu(II) for heterogeneous peroxymonosulfate activation to degrade diclofenac: Performance, mechanism and toxicity assessment

Advanced oxidation processes (AOPs) based on heterogeneous catalytic activated peroxymonosulfate (PMS) have been becoming alternatives to conventional wastewater treatment technologies to directly degrade chemical contaminants. To build dual/multi redox cycles of different metal ions may be an effective means for better PMS activation. Herein, this study designed Mn₃O₄/CuBi₂O₄ with dual redox cycles of Mn(III)/Mn(IV) and Cu(I)/Cu(II) to activate PMS for efficiently decomposing and mineralizing diclofenac sodium (DCF). Under optimal reaction conditions, DCF (50 mg/L) was degraded totally within 10 min, and TOC removal rate reached up to 74.3%. The possible mechanism of PMS activation by Mn₃O₄/CuBi₂O₄ was proposed, wherein dual redox cycles of Mn(III)/Mn(IV) and Cu(I)/Cu(II) on Mn₃O₄/CuBi₂O₄ effectively facilitated PMS activation to generate ·O₂^-, ¹O₂, SO₄·^- and ·OH, which was responsible for DCF degradation. Moreover, combined with degraded products detected by high resolution liquid chromatography coupled to mass spectrometry and corresponding toxic assessment results, the possible degradation pathways of DCF were proposed and the relative toxicity of degraded products was evaluated. This work may be useful for developing stronger heterogeneous activators of PMS to construct more efficient AOPs for purifying wastewater.

A novel electrocatalytic filtration system with carbon nanotube supported nanoscale zerovalent copper toward ultrafast oxidation of organic pollutants

In this study, we designed an integrated electrochemical filtration system for catalytic activation of peroxymonosulfate (PMS) and degradation of aqueous microcontaminants. Composites of carbon nanotube (CNT) and nanoscale zero valence copper (nZVC) were developed to serve as high-performance catalysts, electrode and filtration media simultaneously. We observed both radical and nonradical reaction pathways, which collectively contributed to the degradation of model pollutants. Congo red was completely removed via a single-pass through the nZVCCNT filter (τ <2 s) at neutral pH. The rapid kinetics of Congo red degradation were maintained across a wide pH range (from 3.0-7.0), in complicated matrixes (e.g., tap water and lake water), and for the degradation of a wide array of persistent organic contaminants. The superior activity of nZVCCNT stems from the boosted redox cycles of Cu²⁺/Cu⁺ in the presence of an external electric field. The flow-through design remarkably outperformed the conventional batch system due to the convection-enhanced mass transport. Mechanism studies suggested that the carbonyl group and electrophilic oxygen of CNT served as electron donor and electron acceptor, respectively, to activate PMS to generate •OH and ¹O₂via one-electron transport. The electron-deficient Cu atoms are prone to react with PMS via surface hydroxyl group to produce reactive intermediates (Cu²⁺-O-O-SO₃^-), and then ¹O₂ will be generated by breaking the coordination bond of the metastable intermediate. The study will provide a green strategy for the remediation of organic pollution by a highly efficient and integrated system based on catalytic oxidation, electrochemistry, and nano-filtration techniques.

Emerging Hexagonal Mo2C Nanosheet with (002) Facet Exposure and Cu Incorporation for Peroxymonosulfate Activation Toward Antibiotic Degradation

The catalyst with a special exposed active facet and multivalent element synergism is much desired for advanced oxidation progress (AOP) reaction. Herein, an emerging substrate, Cu-incorporated Mo₂C, with an active (002) facet exposed was developed by one-step calcination to activate peroxymonosulfate (PMS) toward antibiotic degradation. Combining the multivalent Cu-Mo synergistic effect and Cu complexing interaction, Cu was incorporated onto the Mo₂C surface to further enhance its antibiotic removal through PMS activation. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) measurements indicated the 5% Cu-Mo₂C exhibited in the hexagonal nanosheet with Cu uniformly dispersed on the surface. Moreover, 5% Cu-Mo₂C displayed excellent PMS activation which could fully degrade the tetracycline (TC) within 20 min, and the degradation rate was found to be at least 20 times higher than those of pure Mo₂C, classical Fe₂O₃ and Co₃O₄, and Fenton reaction of 5% Cu-Mo₂C. The results were found to be ascribed to enhanced electrical conductivity, multivalent Cu-Mo synergism, and increased generation of active radicals which contributed in the sequence SO₄•^- > •OH > O₂^•-. Surface chemical analysis combined with density functional theory (DFT) calculations confirmed that both Cu²⁺/Cu⁺ and Mo⁶⁺/Mo⁴⁺/Mo²⁺ redox cycles occurred on the (002) plane of Mo₂C, which dominated more free electrons and mainly accounted for facilitating PMS activation. Meanwhile, systematically conditional experiments uncovered that the 5% Cu-Mo₂C exhibited superb catalysis even under a wide pH and temperature, various natural polluted waters and coexisting ions, and long-time recycle. In addition, the as-prepared catalyst presented excellent adaptability for the degradation of different organic effluents originated from medical, dyeing, and beneficiation wastewaters. Considering its great performance, stability, and applicability, 5% Cu-Mo₂C would be a capable candidate for PMS activation toward large-scale practical application in environmental remediation.

CuCo alloy nanonets derived from CuCo2O4 spinel oxides for higher alcohols synthesis from syngas

Porous CuCo alloy nanonets were used as superior catalysts for higher alcohol synthesis from syngas. The catalyst was fabricated via structural topological transformation of CuCo2O4 spinel precursor.

Degradable self-adhesive epidermal sensors prepared from conductive nanocomposite hydrogel

Conductive hydrogel-based epidermal sensors are attracting significant interest due to their great potential in soft robotics, electronic skins, bioelectronics and personalized healthcare monitoring. However, the conventional conductive hydrogel-based epidermal sensors cannot be degraded, resulting in the significant problem of waste, which will gradually increase the burden on the environment. Herein, degradable adhesive epidermal sensors were assembled using conductive nanocomposite hydrogels, which were prepared via the conformal coating of cellulose nanofiber (CNF) networks and supramolecular interaction among CNF, polydopamine (PDA), Fe³⁺, and polyacrylamide (PAM). They exhibited superior mechanical properties, reliable degradability (30 days in water), and excellent self-adhesiveness. The obtained hydrogels could be assembled as self-adhesive, degradable epidermal sensors for real-time human motion monitoring. Air could be sucked into the hydrogels during their swelling process, thereby oxidizing the tris-catechol-Fe³⁺ complexes and releasing Fe³⁺. Finally, the polymer networks were degraded via a Fenton-like reaction dominated by S₂O₈^2- and Fe(ii/iii) with the help of the catechol groups of PDA. This work paves the way for the potential fabrication of degradable, and self-adhesive epidermal sensors for applications in human-machine interactions, implantable bioelectronics, and personalized healthcare monitoring.