Top-Down Direct Preparation of Orange-Yellow Dye Similar to Psittacofulvins from Commercial Polymer by Laser Writing

CO2-Sourced Polymer Dyes for Dual Information Encryption

Large amounts of small molecule dyes leak into the ecosystems annually in harmful and unsustainable ways. Polymer dyes have attracted much attention because of their high migration resistance, excellent stability, and minimized leakage. However, the complex synthesis process, high cost, and poor degradability hinder their widespread application. Herein, green and sustainable polymer dyes are prepared using natural dye quercetin (Qc) and CO2 through a one-step process. The CO2-sourced polymer dyes show strong migration resistance, high stability, and can be degraded on demand. Additionally, the CO2-sourced polymer dyes showed unique responses to Zn2+, leading to significantly enhanced fluorescence, highlighting their potential for information encryption/decryption. The CO2-sourced polymer dyes can solve the environmental hazards caused by small molecule dye leakage and promote the carbon cycle process. Meanwhile, the one-step synthesis process is expected to achieve sustainable and widespread utilization of CO2-sourced polymer dyes.

A fully π-conjugated covalent organic framework with dual binding sites for ultrasensitive detection and removal of divalent heavy metal ions

Covalent organic frameworks (COFs) have become a promising candidate for the remediation of heavy metal pollution. However, researches on COF adsorbents still have challenges on maintaining good optical properties and adsorption performance under harsh conditions. Herein, a fully π-conjugated COF with dual binding sites (Bpy-sp2c-COF) is reported for rapid fluorescence recognition and enhanced adsorption towards divalent heavy metal ions. The vinylene-linkage lattice shows strong luminescence and excellent stability in both strong acidity and basicity. Bpy-sp2c-COF demonstrates not only nanomolar-scale detection of divalent heavy metal ions, but also good adsorption capacity (Hg2+ 718.48, Ni2+ 278.64, Cu2+ 260.11, and Co2+ 126.23 mg/g). Experimental and theoretical studies reveal the intramolecular charge transfer as the fluorescence quenching mechanism. Further simulation results demonstrate the cyano and bipyridine groups on the lattice can act as dual binding sites for divalent heavy metal ions. Experimental results confirmed the adsorption capacity of Bpy-sp2c-COF superior to that of COFs with either cyano groups (Hg2+ 415.34, Ni2+ 165.60, Cu2+ 160.55, and Co2+ 73.14 mg/g), or bipyridine groups (Hg2+ 369.25, Ni2+ 133.41, Cu2+ 133.32, and Co2+ 69.23 mg/g). Besides, robust regeneration of the adsorbent could be achieved over 10 cycles. The fully π-conjugated COF with dual binding sites provides a new approach for designing next-generation sensors and adsorbents with excellent performances.

Decoration of Ultramicrotome-Cut Polymers with Silver Nanoparticles: Effect of Post-Deposition Laser Treatment

Today, ultramicrotome cutting is a practical tool, which is frequently applied in the preparation of thin polymeric films. One of the advantages of such a technique is the decrease in surface roughness, which enables an effective recording of further morphological changes of polymeric surfaces during their processing. In view of this, we report on ultramicrotome-cut polymers (PET, PEEK) modified by a KrF excimer laser with simultaneous decoration by AgNPs. The samples were immersed into AgNP colloid, in which they were exposed to polarized laser light. As a result, both polymers changed their surface morphology while simultaneously being decorated with AgNPs. KrF laser irradiation of the samples resulted in the formation of ripple-like structures on the surface of PET and worm-like ones in the case of PEEK. Both polymers were homogeneously covered by AgNPs. The selected area of the samples was then irradiated by a violet semiconductor laser from the confocal laser scanning microscope with direct control of the irradiated area. Various techniques, such as AFM, FEGSEM, and CLSM were used to visualize the irradiated area. After irradiation, the reverse pyramid was formed for both types of polymers. PET samples exhibited thicker transparent reverse pyramids, whereas PEEK samples showed thinner brownish ones. We believe that his technique can be effectively used for direct polymer writing or the preparation of stimuli-responsive nanoporous membranes.

Preparation and Laser Marking Properties of Poly(propylene)/Molybdenum Sulfide Composite Materials

In this study, using molybdenum sulfide (MoS₂) as laser-sensitive particles and poly(propylene) (PP) as the matrix resin, laser-markable PP/MoS₂ composite materials with different MoS₂ contents ranging from 0.005 to 0.2% were prepared by melt-blending. A comprehensive analysis of the laser marking performance of PP/MoS₂ composites was carried out by controlling the content of laser additives, laser current intensity, and the scanning speed of laser marking. The color difference test shows that the best laser marking performance of the composite can be obtained at the MoS₂ content of 0.02 wt %. The surface morphology of the PP/MoS₂ composite material was observed after laser marking using a metallographic microscope, an optical microscope, and a scanning electron microscope (SEM). During the laser marking process, the laser energy was absorbed and converted into heat energy to cause high-temperature melting, pyrolysis, and carbonization of PP on the surface of the PP/MoS₂ composite material. The black marking from carbonized materials was formed in contrast to the white matrix. Using X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, and Raman spectroscopy, the composite materials before and after laser marking were tested and characterized. The PP/MoS₂ composite material was pyrolyzed to form amorphous carbonized materials. The effect of the laser-sensitive MoS₂ additive on the mechanical properties of composite materials was investigated. The results show that the PP/MoS₂ composite has the best laser marking property when the MoS₂ loading content is 0.02 wt %, the laser marking current intensity is 11 A, and the laser marking speed is 800 mm/s, leading to a clear and high-contrast marking pattern.