Polymeric Quaternary Ammonium-Containing Coatings with Potential Dual Contact-Based and Release-Based Antimicrobial Activity

Controlled Amphiphilicity and Thermo-Responsiveness of Functional Copolymers Based on Oligo(Ethylene Glycol) Methyl Ether Methacrylates

In this work, comb homopolymers as well as comb-type copolymers of thermo-responsive oligo(ethylene glycol methyl ether methacrylate)s, OEGMAs, with various chain lengths (DEGMA, PEGMA500, and PEGMA950 containing 2, 9, or 19 repeating ethylene glycol units, respectively) were synthesized through free radical (co)polymerization. For the copolymers, either the functional hydrophobic glycidyl methacrylate (GMA) or the inert hydrophilic N,N-dimethylacrylamide (DMAM) were selected as comonomers. The self-assembly and thermo-responsive behavior of the products was investigated through Nile Red fluorescence probing, turbidimetry, and dynamic light scattering (DLS). Interestingly, it was found that all OEGMA-based homopolymers exhibit a tendency to self-organize in aqueous media, in addition to thermo-responsiveness. The critical aggregation concentration (CAC) increases with the number of repeating ethylene oxide units in the OEGMA macromonomers (CAC was found to be 0.003, 0.01, and 0.03% w/v for the homopolymers PDEGMA, PPEGMA500, and PPEGMA950, respectively). Moreover, the CAC of the copolymers in aqueous media is highly affected by the incorporation of hydrophobic GMA or hydrophilic DMAM units, leading to lower or higher values, respectively. Thus, the CAC decreases down to 0.003% w/v for the GMA-richest copolymer of PEGMA950, whereas CAC increases up to 0.01% w/v for the DMAM-richest copolymer of DEGMA. Turbidimetry and DLS studies proved that the thermo-sensitivity of the polymers is governed by several parameters such as the number of repeating ethylene glycol groups in the side chains of the OEGMAs, the molar percentage of the hydrophobic or hydrophilic comonomers, along with the addition of salts in the aqueous polymer solutions. Thus, the cloud point of the homopolymer PDEGMA was found at 23 °C and it increases to 33.5 °C for the DMAM-richest copolymer of DEGMA. Lastly, the formation of a hydrogel upon heating aqueous mixtures of the GMA-comprising copolymers with silica nanoparticles overnight is strong evidence of the functional character of these polymers.

Facile Synthesis of Dual-Functional Cross-Linked Membranes with Contact-Killing Antimicrobial Properties and Humidity-Response

Poly(2-hydroxyethylmethacrylate-co-2-(dimethylamino)ethyl methacrylate), P(HEMA-co-DMAEMAx), copolymers were quaternized through the reaction of a part of (dimethylamino)ethyl moieties of DMAEMA units with 1-bromohexadecane. Antimicrobial coatings were further prepared through the cross-linking reaction between the remaining DMAEMA units of these copolymers and the epoxide ring of poly(N,N-dimethylacrylamide-co-glycidyl methacrylate), P(DMAm-co-GMAx), copolymers. The combination of P(HEMA-co-DMAEMAx)/P(DMAm-co-GMAx) copolymers not only enabled control over quaternization and cross-linking for coating stabilization but also allowed the optimization of the processing routes towards a more facile cost-effective methodology and the use of environmentally friendly solvents like ethanol. Careful consideration was given to achieve the right content of quaternized units, qDMAEMA, to ensure antimicrobial efficacy through an appropriate amphiphilic balance and sufficient free DMAEMA groups to react with GMA for coating stabilization. Optimal synthesis conditions were achieved by membranes consisting of cross-linked P(HEMA78-co-DMAEMA9-co-qDMAEMA13)/P(DMAm-co-GMA42) membranes. The obtained membranes were multifunctional as they were self-standing and antimicrobial, while they demonstrated a distinct fast response to changes in humidity levels, widening the opportunities for the construction of "smart" antimicrobial actuators, such as non-contact antimicrobial switches.

Double Photocrosslinked Responsive Hydrogels Based on Hydroxypropyl Guar

Double crosslinked hydrogels based on a biodegradable polymer were prepared by photocopolymerization of methacrylated hydroxypropyl guar (HPG-MA) and 3-acrylamidophenylboronic acid. Along with irreversible strong covalent crosslinks by methacrylic groups, these hydrogels contained labile boronate crosslinks formed as a result of the interaction of boronic acid with cis-diol moieties of HPG. These hydrogels demonstrated higher elasticity than HPG-MA hydrogels with only irreversible covalent crosslinks. Labile boronate crosslinks not only strengthened the hydrogels but also imparted to them pronounced responsive properties. It was demonstrated that the mechanical properties, the swelling behavior, as well as the uptake and release of some substances from the double crosslinked hydrogel were pH controlled. For instance, the hydrogels could release cationic disinfectant at a rate regulated by pH. Such photocrosslinkable in situ forming hydrogels are very promising for the production of smart coatings that release targeted substances at the desired rate.

Development of Antifouling Coatings Based on Quaternary Ammonium Compounds through a Multilayer Approach

The development of polymeric materials as antifouling coatings for aquaculture nets is elaborated in the present work. In this context, cross-linked polymeric systems based on quaternary ammonium compounds (immobilized or releasable) prepared under mild aqueous conditions were introduced as a more environmentally friendly methodology for coating nets on a large scale. To optimize the duration of action of the coatings, a multilayer coating method was applied by combining the antimicrobial organo-soluble copolymer poly(cetyltrimethylammonium 4-styrenesulfonate-co-glycidyl methacrylate) [P(SSAmC16-co-GMA20)] as the first layer with either the water-soluble copolymer poly(vinylbenzyl trimethylammonium chloride-co-acrylic acid) [P(VBCTMAM-co-AA20)] or the water-soluble polymers poly(acrylic acid) (PAA) and poly(hexamethylene guanidine), PHMG, as the second layer. The above-mentioned approach, followed by thermal cross-linking of the polymeric coatings, resulted in stable materials with controlled release of the biocidal species. The coated nets were studied in terms of their antifouling efficiency under accelerated biofouling conditions as well as under real conditions in an aquaculture field. Resistance to biofouling after three water-nutrient replenishments was observed under laboratory accelerated biofouling conditions. In addition, at the end of the field test (day 23) the uncoated nets were completely covered by marine contaminants, while the coated nets remained intact over most of their extent.

Polymer Additives to Personal Protective Equipment can Inactivate Pathogens

Face masks have been proven to be medicine's best public health tool for preventing transmission of airborne pathogens. However, in situations with continuous exposure, lower quality and "do-it-yourself" face masks cannot provide adequate protection against pathogens, especially when mishandled. In addition, the use of multiple face masks each day places a strain on personal protective equipment (PPE) supply and is not environmentally sustainable. Therefore, there is a significant clinical and commercial need for a reusable, pathogen-inactivating face mask. Herein, we propose adding quaternary poly(dimethylaminohexadecyl methacrylate), q(PDMAHDM), abbreviated to q(PDM), to existing fabric networks to generate "contact-killing" face masks-effectively turning cotton, polypropylene, and polyester into pathogen resistant materials. It was found that q(PDM)-integrated face masks were able to inactivate both Gram-positive and Gram-negative bacteria in liquid culture and aerosolized droplets. Furthermore, q(PDM) was electrospun into homogeneous polymer fibers, which makes the polymer practical for low-cost, scaled-up production.

Humidity-Responsive Antimicrobial Membranes Based on Cross-Linked Copolymers Functionalized with Ionic Liquid Moieties

Humidity-responsive materials have attracted increasing attention for their potential use in various applications, e.g., sensors, soft robotics, and human-machine interfaces. Much effort has been focused on the use of ionic liquids for the construction of humidity-responsive sensors; yet, not enough attention has been paid on the susceptibility of the used poly(ionic liquid)s to microorganisms. This is especially relevant to the wide use of the polymers for biomedical applications, e.g., wearable body-condition sensors or healthcare control systems. We herein describe the development of dual functional, self-standing, monolayer antimicrobial membranes derived from cross-linked copolymers functionalized with ionic liquids. In a first step, random copolymers of poly(4-vinylbenzyl N-alkyl imidazolium chloride-co-acrylic acid), P(VBCImC_n-co-AA20), were synthesized bearing aliphatic chains of different lengths (where n = 1, 4, 8, 12, 16 carbon atoms) to investigate the effect of hydrophobicity/hydrophilicity on the humidity-responsive properties of the copolymer and its antimicrobial activity. The aforementioned copolymers were later blended with the complementary reactive copolymers of poly(cetyl trimethylammonium 4-styrene sulfonate-co-glycidyl methacrylate), P(SSAmC₁₆-co-GMA20), to provide highly stable films and coatings through thermal cross-linking. The membrane P(VBCImC₁₂-co-AA20)/P(SSAmC₁₆-co-GMA20) with a molar ratio of 3:1 (mol AA/mol GMA) exhibited immediate and high response to moisture through folding or flipping motions when placed on a wet filter paper or on the palm of a hand. The inhibition of growth for selected bacterial species (Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus) on the copolymer membranes was dependent on the length of the imidazolium alkyl chain and the species. Additionally, in the case of the cross-linked P(VBCImC_n-co-AA20)/P(SSAmC₁₆-co-GMA20) membranes, the overall efficacy was very high against all microorganisms tested, which, combined with their high humidity responsiveness, enables their potential application.

Investigation of Cross-Linked Chitosan-Based Membranes as Potential Adsorbents for the Removal of Cu2+ Ions from Aqueous Solutions

Rapid industrialization has led to huge amounts of organic pollutants and toxic heavy metals into aquatic environment. Among the different strategies explored, adsorption remains until the most convenient process for water remediation. In the present work, novel cross-linked chitosan-based membranes were elaborated as potential adsorbents of Cu²⁺ ions, using as cross-linking agent a random water-soluble copolymer P(DMAM-co-GMA) of glycidyl methacrylate (GMA) and N,N-dimethylacrylamide (DMAM). Cross-linked polymeric membranes were prepared through casting aqueous solutions of mixtures of P(DMAM-co-GMA) and chitosan hydrochloride, followed by thermal treatment at 120 °C. After deprotonation, the membranes were further explored as potential adsorbents of Cu²⁺ ions from aqueous CuSO₄ solution. The successful complexation of copper ions with unprotonated chitosan was verified visually through the color change of the membranes and quantified through UV-vis spectroscopy. Cross-linked membranes based on unprotonated chitosan adsorb Cu²⁺ ions efficiently and decrease the concentration of Cu²⁺ ions in water to a few ppm. In addition, they can act as simple visual sensors for the detection of Cu²⁺ ions at low concentrations (~0.2 mM). The adsorption kinetics were well-described by a pseudo-second order and intraparticle diffusion model, while the adsorption isotherms followed the Langmuir model, revealing maximum adsorption capacities in the range of 66-130 mg/g. Finally, it was shown that the membranes can be effectively regenerated using aqueous H₂SO₄ solution and reused.

Rational Design of Solid Polymer Electrolyte Based on Ionic Liquid Monomer for Supercapacitor Applications via Molecular Dynamics Study

The safety concern arising from flammable liquid electrolytes used in batteries and supercapacitors drives technological advances in solid polymer electrolytes (SPEs) in which flammable organic solvents are absent. However, there is always a trade-off between the ionic conductivity and mechanical properties of SPEs due to the lack of interaction between the ionic liquid and polymer resin. The inadequate understanding of SPEs also limits their future exploitation and applications. Herein, we provide a complete approach to develop a new SPE, consisting of a cation (monomer), anion and hardener from ions-monomers using molecular dynamics (MD) simulations. The results show that the strong solid-liquid interactions between the SPE and graphene electrode lead to a very small gap of ∼5.5 Å between the components of SPE and electrode, resulting in a structured solid-to-liquid interface, which can potentially improve energy storage performance. The results also indicated the critical role of the mobility of free-standing anions in the SPE network to achieve high ionic conductivity for applications requiring fast charge/discharge. In addition, the formations of hardener-depleted regions and cation-anion-poor/rich regions near the uncharged/charged electrode surfaces were observed at the molecular level, providing insights for rationally designing the SPEs to overcome the boundaries for further breakthroughs in energy storage technology.

Environmentally Friendly Hybrid Organic-Inorganic Halogen-Free Coatings for Wood Fire-Retardant Applications

Wood and wood-based products are extensively used in the building sector due to their interesting combination of properties. Fire safety and fire spread, however, are of utmost concern for the protection of buildings. Therefore, in timber structures, wood must be treated with fire-retardant materials in order to improve its reaction to fire. This article highlights the flame retardancy of novel hybrid organic-inorganic halogen-free coatings applied on plywood substrates. For this purpose, either a huntite-rich mineral (H5) or its modified nano-Mg (OH)₂ type form (H5-m), acting as an inorganic (nano) filler, was functionalized with reactive oligomers (ROs) and incorporated into a waterborne polymeric matrix. A water-soluble polymer (P (SSNa-co-GMAx)), combining its hydrophilic nature with functional epoxide groups, was used as the reactive oligomer in order to enhance the compatibility between the filler and the matrix. Among various coating compositions, the system composed of 13% polymeric matrix, 73% H5 and 14% ROs, which provided the best coating quality and flame retardancy, was selected for the coating of plywood on a larger scale in one or two layers. The results indicated that the novel plywood coating systems with the addition of ecological coating formulations (WF-13, WF-14 and WF-15), prepared at two layers, reached Euroclass B according to EN13501-1, which is the best possible for fire systems applied to wood.

Development of Environmentally Friendly Biocidal Coatings Based on Water-soluble Copolymers for Air-cleaning Filters

Air pollution by pathogens has posed serious concern on global health during the last decades, especially since the breakout of the last pandemic. Therefore, advanced high-efficiency techniques for air purification are highly on demand. However, in air-filtering devices, the prevention of secondary pollution that may occur on the filters remains a challenge. Toward this goal, in the present work, we demonstrate a facile and eco-friendly process for the biocidal treatment of commercial high-efficiency particulate air filters. The antibacterial filters were successfully prepared through spray coating of aqueous solutions based on biocidal water-soluble polymers, poly(sodium 4-styrene sulfonate-co-cetyl trimethylammonium 4-styrene sulfonate-co-glycidyl methacrylate) [P(SSNa24-co-SSAmC₁₆56-co-GMA20)] and poly(2-dimethylaminoethyl)methacrylate. Significantly, an optimized green route was developed for the synthesis of the used polymers in aqueous conditions and their stabilization through cross-linking reaction, leading to biocidal air filters with long-lasting activity. The developed coatings presented strong and rapid antibacterial activity against Staphylococcus aureus (in 5 min) and Escherichia coli (in 15 min). Moreover, the cytotoxicity test of the polymeric materials toward Α549 lung adenocarcinoma cells indicated very low toxicity as they did not affect either the cell growth or cell morphology. The above-mentioned results together with the scalable and easy-to-produce green methodology suggest that these materials can be promising candidates as filter coatings for use on air-purification devices.

Antifouling and Antibacterial Surfaces Grafted with Sulfur-Containing Copolymers

Antifouling and antibacterial surfaces that can prevent nonspecific biological adhesion are important to support a myriad of biomedical applications. In this study, we have used an innovative photopolymerization technology to develop sulfur-containing polymer-grafted antifouling and antibacterial surfaces. The relationship between the hydrophilic property and the capability to resist protein and macrophage adsorption of the surface copolymer brushes was investigated. The sulfide monomer incorporated into the surface copolymer brushes can be further ionized to carry positive charges and impart antibacterial activity, leading to surfaces with dual antifouling and antibacterial functions. We believe that the reported sulfur-containing polymer brushes can be considered an emerging and important polymer for antifouling and antibacterial applications.

Self-Patterned Nanoscale Topography of Thin Copolymer Films Prepared by Evaporative Assembly-Resist Early-Stage Bacterial Adhesion

Biofilm formation on the surfaces of indwelling medical devices has become a growing health threat due to the development of antimicrobial resistance to infection-causing bacteria. For example, ventilator-associated pneumonia caused by Pseudomonas and Staphylococci species has become a significant concern in treatment of patients during COVID-19 pandemic. Nanostructured surfaces with antifouling activity are of interest as a promising strategy to prevent bacterial adhesion without triggering drug resistance. In this study, we report a facile evaporative approach to prepare block copolymer film coatings with nanoscale topography that resist bacterial adhesion. The initial attachment of the target bacterium Pseudomonas aeruginosa PAO1 to copolymer films as well as homopolymer films was evaluated by fluorescence microscopy. Significant reduction in bacterial adhesion (93-99% less) and area coverage (>92% less) on the copolymer films was observed compared with that on the control and homopolymer films [poly(methacrylic acid) (PMAA)─only 40 and 23% less, respectively]. The surfaces of poly(styrene)-PMAA copolymer films with patterned nanoscale topography that contains sharp peaks ranging from 20 to 80 nm spaced at 30-50 nm were confirmed by atomic force microscopy and the corresponding surface morphology analysis. Investigation of the surface wettability and surface potential of polymer films assists in understanding the effect of surface properties on the bacterial attachment. Comparison of bacterial growth studies in polymer solutions with the growth studies on coatings highlights the importance of physical nanostructure in resisting bacterial adhesion, as opposed to chemical characteristics of the copolymers. Such self-patterned antifouling surface coatings, produced with a straightforward and energy-efficient approach, could provide a convenient and effective method to resist bacterial fouling on the surface of medical devices and reduce device-associated infections.

Glycidyl Methacrylate-Based Copolymers as Healing Agents of Waterborne Polyurethanes

Self-healing materials and self-healing mechanisms are two topics that have attracted huge scientific interest in recent decades. Macromolecular chemistry can provide appropriately tailored functional polymers with desired healing properties. Herein, we report the incorporation of glycidyl methacrylate-based (GMA) copolymers in waterborne polyurethanes (WPUs) and the study of their potential healing ability. Two types of copolymers were synthesized, namely the hydrophobic P(BA-co-GMAy) copolymers of GMA with n-butyl acrylate (BA) and the amphiphilic copolymers P(PEGMA-co-GMAy) of GMA with a poly(ethylene glycol) methyl ether methacrylate (PEGMA) macromonomer. We demonstrate that the blending of these types of copolymers with two WPUs leads to homogenous composites. While the addition of P(BA-co-GMAy) in the WPUs leads to amorphous materials, the addition of P(PEGMA-co-GMAy) copolymers leads to hybrid composite systems varying from amorphous to semi-crystalline, depending on copolymer or blend composition. The healing efficiency of these copolymers was explored upon application of two external triggers (addition of water or heating). Promising healing results were exhibited by the final composites when water was used as a healing trigger.

Antiseptic Polymer-Surfactant Complexes with Long-Lasting Activity against SARS-CoV-2

Antiseptic polymer gel–surfactant complexes were prepared by incorporating the low-molecular-weight cationic disinfectant cetylpyridinium chloride into the oppositely charged, slightly cross-linked polymer matrices. Three types of polymers were used: copolymers of acrylamide and sodium 2-acrylamido-2-methylpropane sulfonate; copolymers of acrylamide and sodium methacrylate; copolymers of vinylpyrrolidone and sodium methacrylate. It was shown that the rate of the release of the cationic disinfectant from the oppositely charged polymer gels could be tuned in a fairly broad range by varying the concentration of the disinfectant, the degree of swelling, and degree of cross-linking of the gel and the content/type of anionic repeat units in the polymer matrix. Polymer–surfactant complexes were demonstrated to reduce SARS-CoV-2 titer by seven orders of magnitude in as little as 5 s. The complexes retained strong virucidal activity against SARS-CoV-2 for at least one week.

Mussel-Inspired Multicomponent Codeposition Strategy toward Antibacterial and Lubricating Multifunctional Coatings on Bioimplants

Bacterial infections and limited surface lubrication are the two key challenges for bioimplants in dynamic contact with tissues. However, the simultaneous lubricating and antibacterial properties of the bioimplants have rarely been investigated. In this work, we successfully developed a multifunctional coating with simultaneous antibacterial and lubricating properties for surface functionalization of bioimplant materials. The multifunctional coating was fabricated on a polyurethane (PU) substrate via polydopamine (PDA)-assisted multicomponent codeposition, containing polyethyleneimine (PEI) and trace amounts of copper (Cu) as synergistic antibacterial components and zwitterionic poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC) as the lubricating component. The obtained PDA(Cu)/PEI/PMPC coating showed excellent antibacterial activity (antibacterial efficiency: ∼99%) to both Escherichia coli and Staphylococcus aureus compared with bare PU. The excellent antibacterial properties were attributed to the combined effect of anti-adhesion capability of hydrophilic PMPC and PEI and bactericidal activity of Cu in the coating. Meanwhile, the coefficient of friction of the coating was significantly decreased by ∼52% compared with bare PU owing to the high hydration feature of PMPC, suggesting the superior lubricating property. Furthermore, the PDA(Cu)/PEI/PMPC coating was highly biocompatible toward human umbilical vein endothelial cells demonstrated by in vitro cytotoxicity tests. This study not only contributes to the chemistry of PDA-assisted multicomponent codeposition but also provides a facile and practical way for rational design of multifunctional coatings for medical devices.

Multilayered Curcumin-Loaded Hydrogel Microcarriers with Antimicrobial Function

The design of multifunctional microcarriers has attracted significant attention because they combine various functions within a single system. In this study, we developed a set of multilayered hydrogel microcarriers, which were first loaded with chemotherapeutic curcumin (CUR), then, using the layer-by-layer (LbL) technique, coated through a polyelectrolyte shell consisting of chitosan (CHIT) or poly(allylamine hydrochloride) (PAH). As an outer layer with antimicrobial function, newly synthesised alkylene quaternary ammonium salt functionalised polyelectrolytes (A-QAS-PEs) were applied. For this purpose, poly(acrylic acid) (PAA) was decorated with different hydrophobic side chains (n-hexane and n-dodecane side entities) and different degrees of substitution (m) of quaternary ammonium groups (abbreviated as PAA-C(O)O-(CH2)n-N+(CH3)3(m); n = 6, 12; m = 8–14%). The grafting approach of PAA with the alkylene quaternary ammonium salt moiety was performed under mild reaction conditions using Steglich esterification followed by quaternisation. The structure of antimicrobial decorated PAA was confirmed by 1H NMR and FTIR, and the mean diameter of all multifunctional microparticles was characterised by SEM. The viscoelastic properties of the functional layers were studied using quartz crystal microbalance with a dissipation (QCM-D). The release of CUR from the microcarriers was described using a hybrid model, i.e., a combination of first-order kinetics and the Korsmeyer-Peppas model. The antimicrobial activity of functionalised PAA and multilayered CUR-loaded hydrogel microcarriers with quaternary ammonium function was assessed against Staphylococcus aureus and Serratia marcescens by the agar diffusion assay method. Only a limited inhibition zone of PAA was observed, but in the case of both antimicrobial decorated PAA and the corresponding multilayered nanocarriers, the inhibitory activity increase was achieved against both strains of bacteria.

Antimicrobial Photodynamic Coatings Reduce the Microbial Burden on Environmental Surfaces in Public Transportation—A Field Study in Buses

Millions of people use public transportation daily worldwide and frequently touch surfaces, thereby producing a reservoir of microorganisms on surfaces increasing the risk of transmission. Constant occupation makes sufficient cleaning difficult to achieve. Thus, an autonomous, permanent, antimicrobial coating (AMC) could keep down the microbial burden on such surfaces. A photodynamic AMC was applied to frequently touched surfaces in buses. The microbial burden (colony forming units, cfu) was determined weekly and compared to equivalent surfaces in buses without AMC (references). The microbial burden ranged from 0–209 cfu/cm² on references and from 0–54 cfu/cm² on AMC. The means were 13.4 ± 29.6 cfu/cm² on references and 4.5 ± 8.4 cfu/cm² on AMC (p < 0.001). The difference in microbial burden on AMC and references was almost constant throughout the study. Considering a hygiene benchmark of 5 cfu/cm², the data yield an absolute risk reduction of 22.6% and a relative risk reduction of 50.7%. In conclusion, photodynamic AMC kept down the microbial burden, reducing the risk of transmission of microorganisms. AMC permanently and autonomously contributes to hygienic conditions on surfaces in public transportation. Photodynamic AMC therefore are suitable for reducing the microbial load and closing hygiene gaps in public transportation.

Zinc-coordinated polydopamine surface with a nanostructure and superhydrophilicity for antibiofouling and antibacterial applications

A superhydrophilic nanostructured surface of zinc-coordinated polydopamine is formed by the growth and intertwining of the PDA/Zn nanowires via Zn–N and Zn–O bonds, which has potential for preventing biomaterial-associated biofouling and infections.

Preparation of Antimicrobial Coatings from Cross-Linked Copolymers Containing Quaternary Dodecyl-Ammonium Compounds

One of the concerns today’s societies face is the development of resistant pathogenic microorganisms. The need to tackle this problem has driven the development of innovative antimicrobial materials capable of killing or inhibiting the growth of microorganisms. The present study investigates the dependence of the antimicrobial activity and solubility properties on the hydrophilicity/hydrophobicity ratio of antimicrobial coatings based on quaternary ammonium compounds. In this line, suitable hydrophilic and hydrophobic structural units were selected for synthesizing the antimicrobial copolymers poly(4-vinylbenzyl dimethyldodecylammonium chloride-co-acrylic acid), P(VBCDDA-co-AA20) and poly(dodecyltrimethylammonium 4-styrene sulfonate-co-glycidyl methacrylate), P(SSAmC₁₂-co-GMA20), bearing an alkyl chain of 12 carbons either through covalent bonding or through electrostatic interaction. The cross-linking reaction of the carboxylic group of acrylic acid (AA) with the epoxide group of glycidyl methacrylate (GMA) of these two series of reactive antimicrobial copolymers was explored in blends, obtained through solution casting after curing at various temperatures. The release of the final products in pure water and NaCl 1 M solutions (as analyzed by gravimetry and total organic carbon, TOC/total nitrogen, TN analyses), could be controlled by the coating composition. The cross-linked polymeric membranes of composition 60/40 w/w % ratios led to 97.8 and 99.7% mortality for Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), respectively, whereas the coating 20/80 w/w % resulted in 96.6 and 99.8% cell reduction. Despite the decrease in hydrophobicity (from a 16- to a 12-carbon alkyl chain), the new materials maintained the killing efficacy, while at the same time resulting in increased release to the aqueous solution.

Rapid antibacterial activity of anodized aluminum-based materials impregnated with quaternary ammonium compounds for high-touch surfaces to limit transmission of pathogenic bacteria

Infections caused by multidrug-resistant bacteria are a major public health problem. Their transmission is strongly linked to cross contamination via inert surfaces, which can serve as reservoirs for pathogenic microorganisms. To address this problem, antibacterial materials applied to high-touch surfaces have been developed. However, reaching a rapid and lasting effectiveness under real life conditions of use remains challenging. In the present paper, hard-anodized aluminum (AA) materials impregnated with antibacterial agents (quaternary ammonium compounds (QACs) and/or nitrate silver (AgNO₃)) were prepared and characterized. The thickness of the anodized layer was about 50 μm with pore diameter of 70 nm. AA with QACs and/or AgNO₃ had a water contact angle varying between 45 and 70°. The antibacterial activity of the materials was determined under different experimental settings to better mimic their use, and included liquid, humid, and dry conditions. AA-QAC surfaces demonstrated excellent efficiency, killing >99.9% of bacteria in 5 min on a wide range of Gram-positive (Staphylococcus aureus, Clostridioides difficile, vancomycin-resistant Enterococcus faecium) and Gram-negative (streptomycin-resistant Salmonella typhimurium and encapsulated Klebsiella pneumoniae) pathogens. AA-QACs showed a faster antibacterial activity (from 0.25 to 5 min) compared with antibacterial copper used as a reference (from 15 min to more than 1 h). We show that to maintain their high performance, AA-QACs should be used in low humidity environments and should be cleaned with solutions composed of QACs. Altogether, AA-QAC materials constitute promising candidates to prevent the transmission of pathogenic bacteria on high-touch surfaces.

Antimicrobial coatings for environmental surfaces in hospitals: a potential new pillar for prevention strategies in hygiene

Recent reports provide evidence that contaminated healthcare environments represent major sources for the acquisition and transmission of pathogens. Antimicrobial coatings (AMC) may permanently and autonomously reduce the contamination of such environmental surfaces complementing standard hygiene procedures. This review provides an overview of the current status of AMC and the demands to enable a rational application of AMC in health care settings. Firstly, a suitable laboratory test norm is required that adequately quantifies the efficacy of AMC. In particular, the frequently used wet testing (e.g. ISO 22196) must be replaced by testing under realistic, dry surface conditions. Secondly, field studies should be mandatory to provide evidence for antimicrobial efficacy under real-life conditions. The antimicrobial efficacy should be correlated to the rate of nosocomial transmission at least. Thirdly, the respective AMC technology should not add additional bacterial resistance development induced by the biocidal agents and co- or cross-resistance with antibiotic substances. Lastly, the biocidal substances used in AMC should be safe for humans and the environment. These measures should help to achieve a broader acceptance for AMC in healthcare settings and beyond. Technologies like the photodynamic approach already fulfil most of these AMC requirements.

Photo-activated titanium surface confers time dependent bactericidal activity towards Gram positive and negative bacteria

Titanium (Ti)-based implants are broadly applied in the medical field, but their related infections can lead to implant failure. Photo-irradiation of metal materials to generate antimicrobial agents, an alternative to antibiotics, is a promising method to reduce bacterial infection and antibiotic usage. It is therefore important to understand how bacterial pathogens respond to Ti surfaces. Here, Gram-negative Pseudomonas aeruginosa and Gram-positive Staphylococcus aureus, the most prevalent pathogens linked to healthcare-associated infections, were used as model strains. Two different kinds of Ti surfaces respectively stored in dry condition and 0.9 % NaCl solution were applied. Upon UV irradiation and in the absence of bacteria, both tested surfaces exhibited similar bactericidal activity, even though the surfaces stored in 0.9 % NaCl solution generated a slightly higher level of reactive oxygen species (ROS). Interestingly, P. aeruginosa and S. aureus responded to the irradiated Ti surfaces differently regarding interaction time: the number of viable P. aeruginosa was reduced up to 90 % after 30 min interaction with the treated surfaces compared to the untreated ones, but this reduction is lessened to 69 %-81 % after 240 min. By contrast, UV treatment of surfaces did not impact the viability of S. aureus after 30 min interaction, however, led to more than 99 % reduction after 240 min incubation. These results provide first experimental evidence that Gram negative and positive bacterial species respond to ROS with different inactivation kinetics. This work also demonstrated that treatment with photo-irradiation in the absence of bacteria conferred Ti surfaces with efficient bactericidal activity.

Quaternary Ammonium Compounds (QACs) and Ionic Liquids (ILs) as Biocides: From Simple Antiseptics to Tunable Antimicrobials

Quaternary ammonium compounds (QACs) belong to a well-known class of cationic biocides with a broad spectrum of antimicrobial activity. They are used as essential components in surfactants, personal hygiene products, cosmetics, softeners, dyes, biological dyes, antiseptics, and disinfectants. Simple but varied in their structure, QACs are divided into several subclasses: Mono-, bis-, multi-, and poly-derivatives. Since the beginning of the 20th century, a significant amount of work has been dedicated to the advancement of this class of biocides. Thus, more than 700 articles on QACs were published only in 2020, according to the modern literature. The structural variability and diverse biological activity of ionic liquids (ILs) make them highly prospective for developing new types of biocides. QACs and ILs bear a common key element in the molecular structure-quaternary positively charged nitrogen atoms within a cyclic or acyclic structural framework. The state-of-the-art research level and paramount demand in modern society recall the rapid development of a new generation of tunable antimicrobials. This review focuses on the main QACs exhibiting antimicrobial and antifungal properties, commercial products based on QACs, and the latest discoveries in QACs and ILs connected with biocide development.

Environmentally Friendly Cross-Linked Antifouling Coatings Based on Dual Antimicrobial Action

The synthesis of environmentally friendly antimicrobial polymeric coatings, especially in the case of aquaculture, that inhibit the growth of bio-deposits is a very important issue that will contribute to the cost reduction of nets’ cleaning process as well as the protection of the submarine wealth from the biostatic substances used so far. In the present work, the antimicrobial polymers P(SSAmC₁₆-co-VBCHAMx) and the terpolymer P(SSAmC₁₆w-co-VBCHAMx-co-GMAy) were synthesized, bearing quaternary ammonium compounds, electrostatically bound and covalently attached at the same polymer chain. The combination of the two types is of particular importance, as it can provide effective antimicrobial polymeric materials with self-polishing capabilities as a result of the released nature of the antimicrobial, in combination with the permanent local action of the immobilized species. The cross-linking reaction of the terpolymer P(SSAmC₁₆w-co-VBCHAMx-co-GMAy) with the homopolymer polyacrylic acid (PAA) was tested at 120 °C in terms of the equivalent ratio between epoxy and carboxyl groups. The synthesized polymers were further used for the coating of aquaculture nets and tested in terms of antifouling efficiency in lab and scale-up conditions. Uncoated nets were also used in all applications for comparison reasons. The coated nets performed efficiently for 35 days in lab-scale and 66 days in scale-up conditions, showing a high antifouling activity in both fields compared to the uncoated nets.

Dual-Functional, Superhydrophobic Coatings with Bacterial Anticontact and Antimicrobial Characteristics

Bacterial pathogens are responsible for millions of cases of illnesses and deaths each year throughout the world. The development of novel surfaces and coatings that effectively inhibit and prevent bacterial attachment, proliferation, and growth is one of the crucial steps for tackling this global challenge. Herein, we report a dual-functional coating for aluminum surfaces that relies on the controlled immobilization of lysozyme enzyme (muramidase) into interstitial spaces of presintered, nanostructured thin film based on ∼200 nm silica nanoparticles and the sequential chemisorption of an organofluorosilane to the available interfacial areas. The mean diameter of the resultant lysozyme microdomains was 3.1 ± 2.5 μm with an average spacing of 8.01 ± 6.8 μm, leading to a surface coverage of 15.32%. The coating had an overall root-mean-square (rms) roughness of 539 ± 137 nm and roughness factor of 1.50 ± 0.1, and demonstrated static, advancing, and receding water contact angles of 159.0 ± 1.0°, 155.4 ± 0.6°, and 154.4 ± 0.6°, respectively. Compared to the planar aluminum, the coated surfaces produced a 6.5 ± 0.1 (>99.99997%) and 4.0 ± 0.1 (>99.99%) log-cycle reductions in bacterial surfaces colonization against Gram-negative Salmonella Typhimurium LT2 and Gram-positive Listeria innocua, respectively. We anticipate that the implementation of such a coating strategy on healthcare environments and surfaces and food-contact surfaces can significantly reduce or eliminate potential risks associated with various contamination and cross-contamination scenarios.

Film Properties and Antimicrobial Efficacy of Quaternized PDMAEMA Brushes: Short vs Long Alkyl Chain Length

Quaternized poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) brushes bearing quaternary ammonium groups of different alkyl chain lengths (ACLs) were prepared and assessed as biocidal coatings. For the synthesis of the antimicrobial brushes, first well-defined PDMAEMA chains were grown by surface-initiated atom transfer radical polymerization on glass and silicon substrates. Next, the tertiary amine groups of the polymer brushes were modified via a quaternization reaction, using alkyl halides, to obtain the cationic polymers. The polymer films were characterized by Fourier-transform infrared spectroscopy, ellipsometry, atomic force microscopy, and water contact angle measurements. The effect of the ACL of the quaternary ammonium groups on the physicochemical properties of the films as well as the contact killing efficiency of the surfaces against representative Gram-positive and Gram-negative bacteria was investigated. A hydrophilic to hydrophobic transition of the surfaces and a significant decrease of the degree of quaternization of the DMAEMA moieties was found upon increasing the ACL of the quaternization agent above six carbon atoms, allowing the wettability, the thickness, and the pH-response of the brushes to be tuned via a facile postpolymerization, quaternization reaction. At the same time, antimicrobial tests revealed that the hydrophilic polymer brushes exhibited enhanced bactericidal activity against Escherichia coli and Bacillus cereus, whereas the hydrophobic surfaces showed a significant deterioration of the in vitro bactericidal performance. Our results elucidate the antimicrobial action of quaternized polymer brushes, dictating the appropriate choice of the ACL of the quaternization agent for the development of coatings that effectively inhibit biofilm formation on surfaces.

Polymeric Coatings Based on Water-Soluble Trimethylammonium Copolymers for Antifouling Applications

Crosslinked polymeric materials based on a quaternary trimethylammonium compound were developed and evaluated as potential antifouling coatings. For this purpose, two water-soluble random copolymers, poly(4-vinylbenzyltrimethylammonium chloride-co-acrylic acid) P(VBCTMAM-co-AAx) and poly(N,N-dimethylacrylamide-co-glycidylmethacrylate) P(DMAm-co-GMAx), were synthesized via free radical polymerization. A water based approach for the synthesis of P(VBCTMAM-co-AAx) copolymer was used. Coatings of the complementary reactive copolymers in different compositions were obtained by curing at 120 °C for one day and were used to coat aquaculture nets. These nets were evaluated in respect to their release rate using Total Organic Carbon (TOC) and Total Nitrogen (TN) measurements. Finally, the antifouling efficacy of these newly-composed durable coatings was investigated for 14 days in accelerated conditions. The results showed that this novel polymeric material provides contact-killing antifouling activity for a short time period, whereas it functions efficiently in biofouling removal after high-pressure cleaning.

Modification of Collagen Derivatives with Water-Soluble Polymers for the Development of Cross-Linked Hydrogels for Controlled Release

Novel cross-linked hydrogels were synthesized as potential materials for the development of smart biofertilizers. For this purpose, hydrogels were prepared using collagen hydrolysate recovered from tannery waste. The water-soluble polymer poly(sodium 4-styrenesulfonate-co-glycidyl methacrylate) (P(SSNa-co-GMAx)) was among others used for the cross-linking reaction that combined hydrophilic nature with epoxide groups. The synthetic procedure was thoroughly investigated in order to ensure high percentage of epoxide groups in combination with water-soluble behavior. The copolymer did not show cytotoxicity against normal lung, skin fibroblasts, or nasal polyps fibroblasts. Through the present work, we also present the ability to control the properties of cross-linked hydrogels by altering copolymer's composition and cross-linking parameters (curing temperature and time). Hydrogels were then studied in terms of water-uptake capacity for a period up to six days. The techniques Proton Nuclear Magnetic Resonance (1H NMR), Thermogravimetric Analysis (TGA), Size Exclusion Chromatography (SEC), and Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR) were applied for the characterization of the synthesized copolymers and the cross-linked hydrogels. Three samples of biofertilizers based on collagen hydrolysate functionalized with P(SSNa-co-GMAx) and starch and having nutrients encapsulated (N, P, K) were prepared and characterized by physical-chemical analysis and Energy Dispersive X-ray analysis-Scanning Electron Microscope (EDAX-SEM) in terms of microstructure. Preliminary tests for application as fertilizers were performed including the release degree of oxidable organic compounds.

Synthesis of Imidazolium based PILs and Investigation of Their Blend Membranes for Gas Separation

Polymeric (ionic liquid) (PIL) copolymers bearing cationic imidazolium pendants and polar acrylic acid groups (P(VBCImY-co-AA_x)), which both favor the interaction with CO₂ molecules, have been synthesized and blended with film forming, high glass transition temperature aromatic polyether-based pyridinium PILs (PILPyr). The blend membranes based on the above combination have been prepared and characterized in respect to their thermal and morphological behavior as well as to their gas separation properties. The used copolymers and blends showed a wide range of glass transition temperatures from 32 to 286 °C, while blends exhibited two phase morphology despite the presence of polar groups in the blend components that could participate in specific interactions. Finally, the membranes were studied in terms of their gas separation behavior. It revealed that blend composition, counter anion type and acrylic acid molar percentage affect the gas separation properties. In particular, PILPyr-TFSI/P(VBCImTFSI-co-AA₂₀) blend with 80/20 composition shows CO₂ permeability of 7.00 Barrer and quite high selectivity of 103 for the CO₂/CH₄ gas pair. Even higher CO₂/CH_4. selectivity of 154 was achieved for PILPyr-BF₄/P(VBCImBF₄-co-AA₁₀) blend with composition 70/30.

pH-Degradable imidazolium oligomers as antimicrobial materials with tuneable loss of activity

Imidazolium oligomers containing pH-sensitive linkers degrade under basic conditions to less active fragments that slow the development of bacterial resistance.

Anodized Aluminum with Nanoholes Impregnated with Quaternary Ammonium Compounds Can Kill Pathogenic Bacteria within Seconds of Contact

Bacterial contamination of surfaces results in the spread of pathogens in public spaces such as hospitals and public transport. The development of antibacterial surfaces that rapidly kill bacteria is therefore highly desirable. Here, we investigate the antibacterial efficacy of a novel anodized aluminum surface featuring nanoholes impregnated with quaternary ammonium compounds, referred to as A3S. The antimicrobial activity of A3S was assessed using both Gram-positive and Gram-negative bacteria in a novel assay which simulates pathogen transfer from a contaminated "finger" to a clean finger in a real-world scenario. Enumeration of colony-forming units shows that the number of viable bacteria on the second "finger" contacting A3S is significantly reduced compared to a control surface. Furthermore, bacterial contact with the A3S material results in compromised cell membranes in less than 1 min, and a kill zone assay shows that an exposure time as short as 5 s is sufficient to kill pathogenic bacteria. The rapid antimicrobial action of A3S was particularly evident against Gram-positive bacteria, that account for more than 70% of nosocomial infections. Taken together, these findings demonstrate that A3S is a promising candidate for the fabrication of antibacterial surfaces that can be used in a wide range of clinical and commercial applications to stop the spread of harmful bacteria.

Substrate-Independent Ag-Nanoparticle-Loaded Hydrogel Coating with Regenerable Bactericidal and Thermoresponsive Antibacterial Properties

We report a Ag-nanoparticle (AgNP)-based substrate-independent bactericidal hydrogel coating with thermoresponsive antibacterial property. To attach the hydrogel coating onto model substrate, we first coated ene-functionalized dopamine on the substrate, and then the hydrogel thin layer was formed on the surface via the UV light initiated surface cross-linking copolymerization of N-isopropylacrylamide (NIPAAm) and sodium acrylate (AANa). Then, Ag ions were adsorbed into the hydrogel layers and reduced to AgNPs by sodium borohydride. The coating showed robust bactericidal ability against Escherichia coli and Staphylococcus aureus toward both contacted bacteria and the bacteria in the surrounding. Upon a reduction of the temperature below the LCST of PNIPAAm, the improved surface hydrophilicity and swollen PNIPAAm could detach the attached dead bacteria. Meanwhile, the long-lasting and regenerable antibacterial properties could be achieved by repeatedly loading AgNPs. By precisely controlling the AgNP loading amounts, the coating showed excellent hemocompatibility and no cytotoxity. Additionally, the coating could be applied to modify cell culture plate, since it could support cell adhesion and proliferation at 37 °C, while detach the cell by changing the temperature below lower critical solution temperature without the treatment of proteases. The study thus presents a promising way to fabricate thermoresponsive and regenerable antibacterial surfaces on diverse materials and devices for biomedical applications.

Durable Anti-Superbug Polymers: Covalent Bonding of Ionic Liquid onto the Polymer Chains

Here, we fabricated the ionic liquid (IL) grafted poly(vinylidene fluoride) (PVDF) (PVDF-g-IL) via electron-beam irradiation to fight common bacteria and multidrug-resistant "superbugs". Two types of ILs, 1-vinyl-3-butylimmidazolium chloride (IL (Cl)) and 1-vinyl-3-ethylimidazolium tetrafluoroborate (IL (BF₄)), were used. It was found that the PVDF-g-IL exhibited superior antibacterial performance, with almost the same mechanical and thermal performance as unmodified PVDF. Nonwovens and films made from PVDF-g-IL materials exhibited broad-spectrum antimicrobial activity against common bacteria and "superbugs" with the strong electrostatic interactions between ILs and microbial cell membranes. With extremely low IL loading (0.05 wt %), the cell reduction of PVDF-g-IL (Cl) nonwovens improved from 0.2 to 4.4 against S. aureus. Moreover, the antibacterial activity of PVDF-g-IL nonwovens was permanent for the covalent bonds between ILs and polymer chains. The work provides a simple strategy to immobilize ionic antibacterial agents onto polymer substrates, which may have great potential applications in healthcare and household applications.