Importance of Substrate Functionality on the Adhesion and Debonding of a Pressure-Sensitive Adhesive under Water

Adhesion and Contact Aging of Acrylic Pressure-Sensitive Adhesives to Swollen Elastomers

Fluid-infused (or swollen) elastomers are known for their antiadhesive properties. The presence of excess fluid at their surface is the main contributor to limiting contact formation and minimizing adhesion. Despite their potential, the mechanisms for adhesion and contact aging to fluid-infused elastomers are poorly understood beyond contact with a few materials (ice, biofilms, glass). This study reports on adhesion to a model fluid-infused elastomer, poly(dimethylsiloxane) (PDMS), swollen with silicone oil. The effects of oil saturation, contact time, and the opposing surface are investigated. Specifically, adhesion to two different adherents with comparable surface energies but drastically different mechanical properties is investigated: a glass surface and a soft viscoelastic acrylic pressure-sensitive adhesive film (PSA, modulus ∼25 kPa). Adhesion between the PSA and swollen PDMS [with 23% (w/w) silicone oil] retains up to 60% of its value compared to contact with unswollen (dry) PDMS. In contrast, adhesion to glass nearly vanishes in contact with the same swollen elastomer. Adhesion to the PSA also displays stronger contact aging than adhesion to glass. Contact aging with the PSA is comparable for dry and unsaturated PDMS. Moreover, load relaxation when the PSA is in contact with the PDMS does not correlate with contact aging for contact with the dry or unsaturated elastomer, suggesting that contact aging is likely caused by chain interpenetration and polymer reorganization within the contact region. Closer to full saturation of the PDMS with oil, adhesion to the PSA decreases significantly and shows a delay in the onset of contact aging that is weakly correlated to the poroelastic relaxation of the elastomer. Additional confocal imaging suggests that the presence of a layer of fluid trapped at the interface between the two solids could explain the delayed (and limited) contact aging to the oil-saturated PDMS.

Interface Stabilization in Adhesion Caused by Elastohydrodynamic Deformation

Interfacial instabilities are common phenomena observed during adhesion measurements involving viscoelastic polymers or fluids. Typical probe-tack adhesion measurements with soft adhesives are conducted with rigid probes. However, in many settings, such as for medical applications, adhesives make and break contact from soft surfaces such as skin. Here we study how detachment from soft probes alters the debonding mechanism of a model viscoelastic polymer film. We demonstrate that detachment from a soft probe suppresses Saffman-Taylor instabilities commonly encountered in adhesion. We suggest the mechanism for interface stabilization is elastohydrodynamic deformation of the probe and propose a scaling for the onset of stabilization.

Bioinspired Underwater Adhesives

Underwater adhesives are in high demand in both commercial and industrial sectors. Compared with adhesives used in dry (air) environments, adhesives used for wet or submerged surfaces in aqueous environments have specific challenges in development and performance. In this review, focus is on adhesives demonstrating macroscopic adhesion to wet/underwater substrates. The current strategies are first introduced for different types of underwater adhesives, and then an overview is provided of the development and performance of underwater adhesives based on different mechanisms and strategies. Finally, the possible research directions and prospects of underwater adhesives are discussed.

Pressure-Sensitive Adhesive with Enhanced and Phototunable Underwater Adhesion

Pressure-sensitive adhesives (PSAs) are extensively used in diverse applications such as semiconductor manufacturing, labeling, and healthcare because of their quick and viscoelasticity-driven physical adhesion to dry surfaces. However, most of the existing PSAs normally fail to maintain or even establish adhesion under harsh conditions, particularly underwater, due to the lack of robust chemical functionalities for chemistry-based adhesion. Meanwhile, these PSAs are incapable of altering the adhesion in response to external stimuli, limiting their employment in applications requiring dynamic adhesion. Here, we develop a chemically functionalized PSA (f-PSA) with enhanced and phototunable underwater adhesion by incorporating an underwater adhesion enhancer (i.e., mussel-inspired catechol) and a photoresponsive functionality (i.e., anthracene) into a standard acrylic PSA matrix. The synergistic coupling of viscoelasticity-driven physical adhesion originating from the matrix with catechol-enabled chemical adhesion secures sufficient interfacial molecular interactions and leads to enhanced underwater adhesion. The efficient dimerization of anthracene via light-triggered cycloaddition facilely mediates the viscoelastic property of f-PSA, rendering the phototunable adhesion. We envision that this f-PSA can open up more opportunities for applications such as underwater manipulation, transfer printing, and medical adhesives.

Coacervate-Based Instant and Repeatable Underwater Adhesive with Anticancer and Antibacterial Properties

Underwater adhesion is a great challenge for the development of adhesives as the attractive interfacial intermolecular interactions are usually weakened by the surface hydration layer. The coacervation process of sessile organisms like marine mussels and sandcastle worms has inspired substantial research interest in the fabrication of long-lasting underwater adhesives, but they generally suffer from time-consuming curing triggered by surrounding environmental changes and cannot reserve the adhesiveness once damaged. Herein, an instant and repeatable underwater adhesive was developed based on the coacervation of tannic acid (TA) and poly(ethylene glycol)₇₇-b-poly(propylene glycol)₂₉-b-poly(ethylene glycol)₇₇ (PEG-PPG-PEG, F68), which was driven by hydrogen-bonding interaction, and the hydrophobic cores of F68 micelles offered an additional cross-linking to enhance the mechanical properties. The TA-F68 coacervates could be facilely painted on different substrates, exhibiting robust and instant underwater adhesion (with adhesion strength up to 1.1 MPa on porcine skin) and excellent repeatability (at least 1000 cycles), superior to the previously reported coacervates. Due to the biological activities of TA, the underwater adhesive displayed innate anticancer and antibacterial properties against different types of cancer cells and bacteria, showing great potential for diverse biomedical applications, such as injectable drug carriers, tissue glues, and wound dressings.

Attractive forces slow contact formation between deformable bodies underwater

Thermodynamics tells us to expect underwater contact between two hydrophobic surfaces to result in stronger adhesion compared to two hydrophilic surfaces. However, the presence of water changes not only energetics but also the dynamic process of reaching a final state, which couples solid deformation and liquid evacuation. These dynamics can create challenges for achieving strong underwater adhesion/friction, which affects diverse fields including soft robotics, biolocomotion, and tire traction. Closer investigation, requiring sufficiently precise resolution of film evacuation while simultaneously controlling surface wettability, has been lacking. We perform high-resolution in situ frustrated total internal reflection imaging to track underwater contact evolution between soft-elastic hemispheres of varying stiffness and smooth-hard surfaces of varying wettability. Surprisingly, we find the exponential rate of water evacuation from hydrophobic-hydrophobic (adhesive) contact is three orders of magnitude lower than that from hydrophobic-hydrophilic (nonadhesive) contact. The trend of decreasing rate with decreasing wettability of glass sharply changes about a point where thermodynamic adhesion crosses zero, suggesting a transition in mode of evacuation, which is illuminated by three-dimensional spatiotemporal height maps. Adhesive contact is characterized by the early localization of sealed puddles, whereas nonadhesive contact remains smooth, with film-wise evacuation from one central puddle. Measurements with a human thumb and alternatively hydrophobic/hydrophilic glass surface demonstrate practical consequences of the same dynamics: adhesive interactions cause instability in valleys and lead to a state of more trapped water and less intimate solid-solid contact. These findings offer interpretation of patterned texture seen in underwater biolocomotive adaptations as well as insight toward technological implementation.

Immobilized Precursor Particle Driven Growth of Centimeter-Sized MoTe2 Monolayer

Molybdenum ditelluride (MoTe₂) has attracted ever-growing attention in recent years due to its novel characteristics in spintronics and phase-engineering, and an efficient and convenient method to achieve large-area high-quality film is an essential step toward electronic applications. However, the growth of large-area monolayer MoTe₂ is challenging. Here, for the first time, we achieve the growth of a centimeter-sized monoclinic MoTe₂ monolayer and manifest the mechanism of immobilized precursor particle driven growth. Microscopic characterizations reveal an obvious trend of immobilized precursor particles being consumed by the monolayer and continuing to provide a source for the growth of the monolayer. Time-of-flight secondary ion mass spectrometry verifies the attachment of hydroxide ions on the surface of the MoTe₂ monolayer, thereby realizing the inhibition of crystal growth along the [001] zone axis and the continuous growth of the MoTe₂ monolayer. The first-principles DFT calculations prove the mechanism of immobilized precursor particles and the absorption of hydroxide ions on the MoTe₂ monolayer. The as-grown MoTe₂ monolayer exhibits a surface roughness of 0.19 nm and average conductivity of 1.5 × 10^-5 S/m, which prove the smoothness and uniformity of the MoTe₂ monolayer. Temperature-dependent electrical measurements together with the transfer characteristic curves further demonstrate the typical semimetallic properties of monoclinic MoTe₂. Our research elaborates the microscopic process of immobilized precursor particles to grow large-area MoTe₂ monolayer and provides a new thinking about the growth of many other two-dimensional materials.

High-Throughput Screening Test for Adhesion in Soft Materials Using Centrifugation

High-throughput screening of mechanical properties can transform materials science research by both aiding in materials discovery and developing predictive models. However, only a few such assays have been reported, requiring custom or expensive equipment, while the mounting demand for enormous data sets of materials properties for predictive models is unfulfilled by the current characterization throughput. We address this problem by developing a high-throughput colorimetric adhesion screening method using a common laboratory centrifuge, multiwell plates, and microparticles. The technique uses centrifugation to apply a homogeneous mechanical detachment force across individual formulations in a multiwell plate. We also develop a high-throughput sample deposition method to prepare films with uniform thickness in each well, minimizing well-to-well variability. After establishing excellent agreement with the well-known probe tack adhesion test, we demonstrate the consistency of our method by performing the test on a multiwell plate with two different formulations in an easily discernible pattern. The throughput is limited only by the number of wells in the plates, easily reaching 10³ samples/run. With its simplicity, low cost, and large dynamic range, this high-throughput method has the potential to change the landscape of adhesive material characterization.

Chitin Nanocrystals as an Eco-friendly and Strong Anisotropic Adhesive

To solve the damage to the environment and human body caused by organic solvent adhesives in the utilization process, chitin nanocrystal (ChNC) suspension is explored as a strong anisotropic adhesive, which is an eco-friendly and water-based adhesive with high adhesive strength. ChNCs extracted from crab shells are rod-like nanoparticles with high aspect ratios, which are mainly employed as reinforcing polymer nanocomposites and biomedicine nanomaterials. ChNC suspension sandwiched between substrates forms a long-range ordered superstructure by a self-assembly process. ChNC nanoglue exhibits high anisotropy adhesion strength, i.e., an in-plane shear strength (5.26 MPa) and an out-of-plane shear strength (0.46 MPa) for glass substrates. Moreover, the ChNC nanoglue is suitable to many substrates, such as glass, plastic, wood, metal, paper, etc. The ChNC nanoglue shows high biocompatibility toward the fibroblast cell and rat skin, proving their excellent biosafety. As an eco-friendly and high-performance adhesive, ChNC nanoglue shows promising applications in daily life and industrial fields.

Adhesive Coacervates Driven by Hydrogen-Bonding Interaction

Coacervation plays a critical role in numerous biological activities such as constructing biological tissues and achieving robust wet adhesion of marine sessile organisms, which conventionally occurs when oppositely charged polyelectrolytes are mixed in aqueous solutions driven by electrostatic attraction. Here, a novel type of adhesive coacervate is reported, driven by hydrogen-bonding interactions, readily formed by mixing silicotungstic acid and nonionic polyethylene glycol in water, providing a new approach for developing coacervates from nonionic systems. The as-prepared coacervate is easily paintable underwater, show strong wet adhesion to diverse substrates, and has been successfully applied as a hemostatic agent to treat organ injuries without displaying hemolytic activity, while with inherent antimicrobial properties thus avoiding inflammations and infections due to microorganism accumulation. This work demonstrates that coacervation can occur in salt-free environments via non-electrostatic interactions, providing a new platform for engineering multifunctional coacervate materials as tissue glues, wound dressings and membrane-free cell systems.

Pressure-Sensitive Adhesive with Controllable Adhesion for Fabrication of Ultrathin Soft Devices

As the interest in foldable smartphones recently launched onto the market shifts toward the next generation of flexible electronics, the development of ultrathin devices is gaining considerable attention. The strain formed on the surfaces of film-based devices approximates the film thickness divided by twice the radius of curvature; therefore, the use of an ultrathin substrate is the key for the development of next generation foldable devices. However, the stiffness of ultrathin films is extremely low; thus, it cannot be easily used directly as a substrate for device fabrication. Therefore, these films generally undergo device manufacturing processes while being attached to a rigid substrate such as glass and are peeled from the rigid substrate after the process is finished. Thus, the initial adhesion of the adhesive used to fix the film to the temporary substrate should be strong, and after the process is completed, the adhesion must be lessened to enable soft peeling. In this study, we succeeded in developing a novel pressure-sensitive adhesive (PSA) whose adhesive strength can be severely reduced by water treatment. Accordingly, considering that amphiphilic oligomers promote water absorption through hydrogen bonding to water, amphiphilic oligomers were mixed with an acrylic polymer to prepare the water-responsive PSA (wr-PSA). The adhesion strength of the wr-PSA in the early stage, which reached 382(±22) N/m, dramatically dropped to 9(±2) N/m after a water immersion test. Using the wr-PSA, a 1.4 μm-thick polyethylene terephthalate film coated with Ag nanowires was softly peeled off from the glass after being immersed in warm water. In addition, the adhesion reduced by the immersion in water was recovered again when the water absorbed by the adhesive was dried. This implies that the developed adhesive can be reusable.

Pressure-Sensitive Tissue Adhesion and Biodegradation of Viscoelastic Polymer Blends

Viscoelastic blends of biodegradable polyesters with low and high molecular weight distributions have remarkably strong adhesion (significantly greater than 1 N/cm2) to soft, wet tissue. Those that transition from viscous flow to elastic, solidlike behavior at approximately 1 Hz demonstrate pressure-sensitivity yet also have sufficient elasticity for durable bonding to soft, wet tissue. The pressure-sensitive tissue adhesive (PSTA) blends produce increasingly stronger pull-apart adhesion in response to compressive pressure application, from 10 to 300 s. By incorporating a stiffer high molecular weight component, the PSTA exhibits dramatically improved burst pressure (greater than 100 kPa) when used as a tissue sealant. The PSTA's biodegradation mechanism can be switched from erosion (occurring primarily over the first 10 days) to bulk chemical degradation (and minimal erosion) depending on the chemistry of the high molecular weight component. Interestingly, fibrosis toward the PSTA is reduced when fast-occurring erosion is the dominant biodegradation mechanism.

Enhanced Adhesion and Cohesion of Bioinspired Dry/Wet Pressure-Sensitive Adhesives

The byssus-mediated adhesion of marine mussels is a widely mimicked system for robust adhesion in both dry and wet conditions. Mussel holdfasts are fabricated from proteins that contain a significant amount of the unique catecholic amino acid dihydroxyphenylalanine, which plays a key role in enhancing interfacial adhesion to organic and inorganic marine surfaces and contributes to cohesive strength of the holdfast. In this work, pressure-sensitive adhesives (PSAs) were synthesized by copolymerization of dopamine methacrylamide (DMA) with common PSA monomers, butyl acrylate and acrylic acid, with careful attention paid to the effects of catechol on adhesive and cohesive properties. A combination of microscopic and macroscopic adhesion assays was used to study the effect of catechol on adhesion performance of acrylic PSAs. Addition of only 5% DMA to a conventional PSA copolymer containing butyl acrylate and acrylic acid resulted in 6-fold and 2.5-fold increases in work required to separate the PSA from silica and polystyrene, respectively, and a large increase in 180° peel adhesion against stainless steel after 24 h storage in both ambient and underwater conditions. Moreover, the holding power of the catechol PSAs on both steel and high-density polyethylene under shear load continuously increased as a function of catechol concentration, up to a maximum of 10% DMA. We also observed stark increases in shear and peel adhesion for the catecholic adhesives over PSAs with noncatecholic aromatic motifs, further underlining the benefits of catechols in PSAs. Overall, catechol PSAs perform extremely well on polar and metallic surfaces. The advantage of incorporating catechols in PSA formulations, however, is less straightforward for peel adhesion in nonpolar, organic substrates and tackiness of the PSAs.

Contribution of Surface Energy to pH-Dependent Underwater Adhesion of an Acrylic Pressure-Sensitive Adhesive

Maintaining the underwater adhesive performance over a broad range of solution pH is challenging but necessary for many biomedical applications. Therefore, understanding how environmental conditions influence the mechanisms of bonding and debonding of pressure-sensitive adhesives (PSAs) can provide guidelines for materials design. We investigate how the presence of acrylic acid as a co-monomer impacts the adhesion of a model PSA in aqueous environments of varying pH. The adhesives under investigation are poly(2-ethylhexyl acrylate), or poly(2-EHA), and poly(2-EHA) co-polymerized with 5 wt % acrylic acid, or poly(2-EHA- co-AA). We characterize bonding and debonding (adhesion) of the adhesives using probe tack measurements with a spherical hydrophobic glass probe. We analyze the performance of the two PSAs in air and in low-ionic-strength buffered aqueous solutions of pH 3- 11. We find that the presence of the acrylic acid co-monomer increases the cohesiveness of the PSA and leads to stronger adhesion under all conditions investigated. We also observe that the presence of the acrylic acid co-monomer imparts the PSA with a strong dependence of adhesion on the solution pH. Dynamic contact angle and  ζ potential measurements support the hypothesis that deprotonation of the acrylic acid groups at higher pH causes the decrease in adhesion at higher pH. Rheological measurements do not show changes in the dynamic mechanical properties of the PSAs after exposure to solutions of pH 3- 11. Our measurements allow us to isolate the effect of the solution pH on the surface and bulk properties of the PSA. In the absence of the acrylic acid co-monomer, the bulk dissipation and the surface properties of the PSA are independent of the solution's pH.

Morphology of soft and rough contact via fluid drainage

The dynamic of contact formation between soft materials immersed in a fluid is accompanied by fluid drainage and elastic deformation. As a result, controlling the coupling between lubrication pressure and elasticity provides strategies to design materials with reversible and dynamic adhesion to wet or flooded surfaces. We characterize the elastic deformation of a soft coating with nanometer-scale roughness as it approaches and contacts a rigid surface in a fluid environment. The lubrication pressure during the approach causes elastic deformation and prevents contact formation. We observe deformation profiles that are drastically different from those observed for elastic half-space when the thickness of the soft coating is comparable to the hydrodynamic radius. In contrast, we show that surface roughness favors fluid drainage without altering the elastic deformation. As a result, the coupling between elasticity and slip (caused by surface roughness) can lead to trapped fluid pockets in the contact region.

A multifunctional force microscope for soft matter with in situ imaging

We present the multifunctional force microscope (MFM), a normal and lateral force-measuring instrument with in situ imaging. In the MFM, forces are calculated from the normal and lateral deflection of a cantilever as measured via fiber optic sensors. The motion of the cantilever is controlled normally by a linear micro-translation stage and a piezoelectric actuator, while the lateral motion of the sample is controlled by another linear micro-translation stage. The micro-translation stages allow for travel distances that span 25 mm with a minimum step size of 50 nm, while the piezo has a minimum step size of 0.2 nm, but a 100 μm maximum range. Custom-designed cantilevers allow for the forces to be measured over 4 orders of magnitude (from 50 μN to 1 N). We perform probe tack, friction, and hydrodynamic drainage experiments to demonstrate the sensitivity, versatility, and measurable force range of the instrument.