Direct Three-Dimensional Visualization of Membrane Fouling by Confocal Laser Scanning Microscopy

Electrochemical coalescence of oil-in-water droplets in microchannels of TiO2-x/Ti anode via polarization eliminating electrostatic repulsion and ·OH oxidation destroying oil-water interface film

Electrochemistry is a sustainable technology for oil-water separation. In the common flat electrode scheme, due to a few centimeters away from the anode, oil droplets have to undergo electromigration to and electrical neutralization at the anodic surface before they coalesce into large oil droplets and rise to water surface, resulting in slow demulsification and easy anode fouling. Herein, a novel strategy is proposed on basis of a TiO2-x/Ti anode with microchannels to overcome these problems. When oil droplets with several microns in diameter flow through channels with tens of microns in diameter, the electromigration distance is shortened by three orders of magnitude, electrical neutralization is replaced by polarization coupling ·OH oxidation. The new strategy was supported by experimental results and theoretical analysis. Taking the suspension containing emulsified oil as targets, COD value dropped from initial 500 mg/L to 117 mg/L after flowing through anodic microchannels in only 58 s of running time, and the COD removal was 21 times higher than that for a plate anode. At similar COD removal, the residence time was 48 times shorter than that of reported flat electrodes. Coalescences of oil droplets in microchannels were observed by a confocal laser scanning microscopy. This new strategy opens a door for using microchannel electrodes to accelerate electrochemical coalescence of oil-in-water droplets.

Understanding the "Berg limit": the 65° contact angle as the universal adhesion threshold of biomatter

Surface phenomena in aqueous environments such as long-range hydrophobic attraction, macromolecular adhesion, and even biofouling are predominantly influenced by a fundamental parameter-the water contact angle. The minimal contact angle required for these and related phenomena to occur has been repeatedly reported to be around 65° and is commonly referred to as the "Berg limit." However, the universality of this specific threshold across diverse contexts has remained puzzling. In this perspective article, we aim to rationalize the reoccurrence of this enigmatic contact angle. We show that the relevant scenarios can be effectively conceptualized as three-phase problems involving the surface of interest, water, and a generic oil-like material that is representative of the nonpolar constituents within interacting entities. Our analysis reveals that attraction and adhesion emerge when substrates display an underwater oleophilic character, corresponding to a "hydrophobicity under oil", which occurs for contact angles above approximately 65°. This streamlined view provides valuable insights into macromolecular interactions and holds implications for technological applications.

A comprehensive review on the behavior and evolution of oil droplets during oil/water separation by membranes

Membrane separation technology has significant advantages for treating oil-in-water emulsions. Understanding the evolution of oil droplets could reveal the interfacial and colloidal interactions, facilitate the design of advanced membranes, and improve the separation performances. This review on the characteristic behavior and evolution of oil droplets focuses on the advanced analytical techniques, and the subsequent fouling as well as demulsification effects during membrane separation. A detailed introduction is provided on microscopic observations and numerical simulations of the dynamic evolution of oil droplets, featuring real-time in-situ visualization and accurate reconstruction, respectively. Characteristic behaviors of these oil droplets include attachment, pinning, wetting, spreading, blockage, intrusion, coalescence, and detachment, which have been quantified by specific proposed parameters and criteria. The fouling process can be evaluated using Hermia and resistance models. The related adhesion force and intrusion pressure as well as droplet-droplet/membrane interfacial interactions can be accurately quantified using various force analysis methods and advanced force measurement techniques. It is encouraging to note that oil coalescence has been achieved through various effects such as electrostatic interactions, mechanical actions, Laplace pressure/surface free energy gradients, and synergistic effects on functional membranes. When oil droplets become destabilized and coalesce into larger ones, the functional membranes can overcome the limitations of size-sieving effect to attain higher separation efficiency. This not only bypasses the trade-off between permeability and rejection, but also significantly reduces membrane fouling. Finally, the challenges and potential research directions in membrane separation are proposed. We hope this review will support the engineering of advanced materials for oil/water separation and research on interface science in general.

Three-Dimensional Imaging of Emulsion Separation through Liquid-Infused Membranes Using Confocal Laser Scanning Microscopy

The removal of emulsified oils from water has always been a challenge due to the kinetic stability resulting from the small droplet size and the presence of stabilizing agents. Membrane technology can treat such mixtures, but fouling of the membrane leads to dramatic reductions in the process capacity. Liquid-infused membranes (LIMs) can potentially resolve the issue of fouling. However, their low permeate flux compared with conventional hydrophilic membranes remains a limitation. To gain insight into the mechanism of transport, we use 3D images acquired by confocal laser scanning microscopy (CLSM) to reconstruct the sequence of events occurring during startup and operation of the LIM for removal of dispersed oil from oil-in-water emulsions. We find evidence for coalescence of oil droplets on the surface of and formation of oil channels within the LIM. Using image analysis, we find that the rate at which oil channels are formed within the membrane and the number of channels ultimately govern the permeate flux of oil through the LIMs. Oil concentration in the feed affects the rate of coalescence of oil on the surface of the LIM, which, in turn, affects the channel formation dynamics. The channel formation dynamics also depend on the viscosity of the infused liquid and the operating pressure. A higher affinity to the pore wall for infused liquid than permeating liquid is essential to antifouling behavior. Overall, this work offers insight into the selective permeation of a dispersed liquid phase through a LIM.

Influence of water quality factors on cake layer 3D structures and water channels during ultrafiltration process

The three-dimensional (3D) structure of the cake layer, which could be influenced by water quality factors, plays a significant role in the ultrafiltration (UF) efficiency of water purification. However, it remains challenging to precisely reveal the variation of cake layer 3D structures and water channel characteristics. Herein, we systematically report the variation in the cake layer 3D structure at the nanoscale induced by key water quality factors and reveal its influence on water transport, in particular the abundance of water channels within the cake layer. In comparison with pH and Na+, Ca2+ played more significant role in determining cake layer structures. The sandwich-like cake layer, which was induced by the asynchronous deposition of humic acids and sodium alginate (SA), shifted to an isotropic structure when Ca2+ was present due to the Ca2+ bridging. In comparison with the sandwich-like structure, the isotropic cake layer has higher fractions of free volume (voids) and more water channels, leading to a 147% improvement in the water transport coefficient, 60% reduction in the cake layer resistance, and 21% increase in the final membrane specific flux. Our work elucidates a structure-property relationship where improving the isotropy of the cake layer 3D structure is conducive to the optimization of water channels and water transport within cake layers. This could inspire tailored regulation strategies for cake layers to enhance the UF efficiency of water purification.

Tracking the Dissolution Surface Kinetics of a Single Fluorescent Cyclodextrin Metal-Organic Framework by Confocal Laser Scanning Microscopy

The understanding of the dissolution processes of solids is important for the design and synthesis of solids in a controlled and precise manner and for predicting their fate in the aquatic environment. We report herein single-particle-based confocal laser scanning microscopy (CLSM) for tracking the dissolution surface kinetics of a single fluorescent cyclodextrin metal-organic framework (CD-MOF). As a proof of concept, CD-MOF containing fluorescein, named as CD-MOF⊃FL, was synthesized by encapsulating fluorescein into the interior of CD-MOF via a vapor diffusion method and used as a single-particle dissolution model because of its high FL efficiency and unique structure. The morphology of CD-MOF⊃FL and the distribution of fluorescein within CD-MOF⊃FL were characterized. The growth and dissolution processes of CD-MOF⊃FL at the single-particle level were visualized and quantified for the first time by recording the change of the fluorescence emission. Three processes, including nucleation, germination growth, and saturation stage, were found in the growth of CD-MOF⊃FL, and the growth kinetics followed Avrami's model. The dissolution rate at the face of a single CD-MOF⊃FL crystal was slower than that of its arris, and the dissolution rate of the CD-MOF⊃FL crystal was increased with the increase of the water amount in methanol solution. The dissolution process of the CD-MOF⊃FL crystal was a competitive process of erosion and diffusion in different methanol aqueous solutions, and the dissolution kinetics followed the Korsmeyer-Peppas model. These results offer new insights into the nature of dissolution kinetics of CD-MOF⊃FL and provide new venues for the quantitative analysis of solid dissolution and growth at the single-particle level.

Designing sustainable membrane-based water treatment via fouling control through membrane interface engineering and process developments

Membrane-based water treatment processes have been established as a powerful approach for clean water production. However, despite the significant advances made in terms of rejection and flux, provision of sustainable and energy-efficient water production is restricted by the inevitable issue of membrane fouling, known to be the major contributor to the elevated operating costs due to frequent chemical cleaning, increased transmembrane resistance, and deterioration of permeate flux. This review provides an overview of fouling control strategies in different membrane processes, such as microfiltration, ultrafiltration, membrane bioreactors, and desalination via reverse osmosis and forward osmosis. Insights into the recent advancements are discussed and efforts made in terms of membrane development, modules arrangement, process optimization, feed pretreatment, and fouling monitoring are highlighted to evaluate their overall impact in energy- and cost-effective water treatment. Major findings in four key aspects are presented, including membrane surface modification, modules design, process integration, and fouling monitoring. Among the above mentioned anti-fouling strategies, a large part of research has been focused on membrane surface modifications using a number of anti-fouling materials whereas much less research has been devoted to membrane module advancements and in-situ fouling monitoring and control. At the end, a critical analysis is provided for each anti-fouling strategy and a rationale framework is provided for design of efficient membranes and process for water treatment.

Four-Dimensional Visualization of Microscale Dynamics of Membrane Oil Fouling via Synchrotron Radiation Microcomputed Tomography

Although oil-water separation technology via wettability-controlled membranes has emerged as a promising technology to treat oily wastewater, membrane fouling by faulents such as sludge flocs and colloids, and the consequent clogging of pores, severely degrades the efficiency of filtration systems. One of the main promotors of fouling by faulents is oil fouling, which is also a form of fouling itself. Despite considerable practical and academic interest in the analysis of oil-fouled membranes, direct visualization of the entire process of oil infiltration into hydrophilic membranes is still preliminary owing to (i) the similar optical contrast and physical density between oil and water, (ii) the low penetration depth of imaging methods, and (iii) the lack of 3D segmentation capability. In this study, microcomputed X-ray tomography using tunable synchrotron radiation provided direct high-speed 3D visualization of the microscale dynamics of the oil infiltration of a prewetted hydrophilic filter membrane over time. Direct visualization of the interfacial dynamics of oil infiltration opens a window into the complex liquid (water/oil)-gas-solid interface and thus helps furnish an in-depth understanding of oil fouling in the prewetted membrane.

Deep learning in food science: An insight in evaluating Pickering emulsion properties by droplets classification and quantification via object detection algorithm

Understanding the complicated emulsion microstructures by microscopic images will help to further elaborate their mechanisms and relevance. The formidable goal of the classification and quantification of emulsion microstructure appears difficult to achieve. However, object detection algorithm in deep learning makes it feasible. This paper reports a new technique for evaluating Pickering emulsion properties through classification and quantification of the emulsion microstructure by object detection algorithm. The trained neural network models characterize the emulsion droplets by distinguishing between different individual emulsion droplets and morphological mechanisms from numerous microscopic images. The quantified results of the emulsion droplets presented in this study, provide details of statistical changes at different concentrations of the Pickering interface and storage temperatures enabling elucidation of the mechanisms involved. This methodology provides a new quantitative and statistical analysis of emulsion microstructure and properties.

ZnO Nanoneedle-Modified PEEK Fiber Felt for Improving Anti-fouling Performance of Oil/Water Separation

Membrane separation has been considered to be the most effective decontamination method for oily waste water. The most significant point of membrane separation is the resistance against membrane fouling. Fabricating hierarchical architectures on the membrane surface is an available approach to improving its anti-fouling property. In this study, ZnO nanoneedles were successfully anchored onto surface-sulfonated poly(ether-ether-ketone) (PEEK) felt via UV/ozone cleaning and hydrothermal synthesis. The modified felt (PEEK-f-Z) showed much better anti-fouling properties and far higher rejection height (33 cm) than the unmodified felt (17 cm) with a separation efficiency up to 99.99%. The enhanced separation properties could be attributed to the stronger water locking capability of the hierarchical architectures on the surface. Furthermore, benefiting from the great chemical stability of PEEK substrates and ZnO nanoneedles, the as-prepared membrane exhibited admirable solvent resistance, mechanical strength, and thermal stability. As a result, PEEK-f-Z could even separate immiscible organic liquids with different polarities and collect hot water from the oil/water mixture, promising to be used under severe conditions.

Plasmon-Enhanced Antibacterial Activity of Chiral Gold Nanoparticles and In Vivo Therapeutic Effect

d-cysteine (d-cys) has been demonstrated to possess an extraordinary antibacterial activity because of its unique steric configuration. However, inefficient antibacterial properties seriously hinder its wide applications. Here, cysteine-functionalized gold nanoparticles (d-/l-Au NPs) were prepared by loading d-/l-cysteine on the surface of gold nanoparticles for the effective inhibition of Escherichia coli (E. coli) in vitro and in vivo, and the effects on the intestinal microflora in mice were explored during the treatment of E. coli infection in the gut. We found that the antibacterial activity of d-/l-Au NPs was more than 2-3 times higher than pure d-cysteine, l-cysteine and Au NPs. Compared with l-Au NPs, d-Au NPs showed the stronger antibacterial activity, which was related to its unique steric configuration. Chiral Au NPs showed stronger destructive effects on cell membrane compared to other groups, which further leads to the leakage of the cytoplasm and bacterial cell death. The in vivo antibacterial experiment illustrated that d-Au NPs displayed impressive antibacterial activity in the treatment of E. coli-infected mice comparable to kanamycin, whereas they could not affect the balance of intestinal microflora. This work is of great significance in the development of an effective chiral antibacterial agent.

Atomic Layer Deposition for Gradient Surface Modification and Controlled Hydrophilization of Ultrafiltration Polymer Membranes

In recent years, atomic layer deposition (ALD) has emerged as a powerful technique for polymeric membrane surface modification. In this research, we study Al₂O₃ growth via ALD on two polymeric phase-inverted membranes: polyacrylonitrile (PAN) and polyetherimide (PEI). We demonstrate that Al₂O₃ can easily be grown on both membranes with as little as 10 ALD cycles. We investigate the formation of Al₂O₃ layer gradient through the depth of the membranes using high-resolution transmission electron microscopy and elemental analysis, showing that at short exposure times, Al₂O₃ accumulates at the top of the membrane, reducing pore size and creating a strong growth gradient, while at long exposure time, more homogeneous growth occurs. This detailed characterization creates the knowledge necessary for controlling the deposition gradient and achieving an efficient growth with minimum pore clogging. By tuning the Al₂O₃ exposure time and cycles, we demonstrate control over the Al₂O₃ depth gradient and membranes' pore size, hydrophilicity, and permeability. The oil antifouling performance of membranes is investigated using in situ confocal imaging during flow. This characterization technique reveals that Al₂O₃ surface modification reduces oil droplet surface coverage.

Three-dimensional visualization and analysis of flowing droplets in microchannels using real-time quantitative phase microscopy

Recent years have witnessed the development of droplet-based microfluidics as a useful and effective tool for high-throughput analysis in biological, chemical and environmental sciences. Despite the flourishing development of droplet manipulation techniques, only a few methods allow for label-free and quantitative inspection of flowing droplets in microchannels in real-time and in three dimensions (3-D). In this work, we propose and demonstrate the application of a real-time quantitative phase microscopy (RT-QPM) technique for 3-D visualization of droplets, and also for full-field and label-free measurement of analyte concentration distribution in the droplets. The phase imaging system consists of a linear-CCD-based holographic microscopy configuration and an optofluidic phase-shifting element, which can be used for retrieving quantitative phase maps of flowing objects in the microchannels with a temporal resolution only limited to the frame rate of the CCD camera. To demonstrate the capabilities of the proposed imaging technique, we have experimentally validated the 3-D image reconstruction of the droplets generated in squeezing and dripping regimes and quantitatively investigated the volumetric and morphological variation of droplets as well as droplet parameters related to the depth direction under different flow conditions. We also demonstrated the feasibility of using this technique, as a refractive index sensor, for in-line quantitative measurement of carbamide analyte concentration within the flowing droplets.

Direct Visualization of Microscale Dynamics of Water Droplets on under-Oil-Hydrophilic Membranes by Using Synchrotron White-Beam X-ray Microimaging Techniques

Despite considerable academical and practical interests on separation of water-in-oil emulsion via special wettable membranes, fundamental understanding on microscale dynamics of water droplets on under-oil-hydrophilic membranes (UOHMs) at early stages during separation is still very preliminary due to temporal and spatial resolution of existing visualization techniques. To this end, we here succeed in a direct microscopic visualization of separation processes of water droplets on the UOHMs by employing a high-speed, two-dimensional synchrotron white-beam X-ray microimaging technique. During the separation of water-in-oil emulsion, microscale dynamic behaviors of water droplets on hydrophilic membrane surfaces immersed in the different oil media (i.e., hexane, kerosene, and light and heavy mineral oils) and oil films between water droplets and membrane surfaces are visualized and analyzed.

Green Treatment of Phosphate from Wastewater Using a Porous Bio-Templated Graphene Oxide/MgMn-Layered Double Hydroxide Composite

Excessive phosphorus in water is the primary culprit for eutrophication, which causes approximately $2.2 billion annual economic loss in the United States. This study demonstrates a phosphate-selective sustainable method by adopting Garcinia subelliptica leaves as a natural bio-template, where MgMn-layered double hydroxide (MgMn-LDH) and graphene oxide (GO) can be grown in situ to obtain L-GO/MgMn-LDH. After calcination, the composite shows a hierarchical porous structure and selective recognition of phosphate, which achieves significantly high and recyclable selective phosphate adsorption capacity and desorption rate of 244.08 mg-P g-1 and 85.8%, respectively. The detail variation of LDHs during calcination has been observed via in situ transmission electron microscope (TEM). Moreover, the roles in facilitating phosphate adsorption and antimicrobial ability of chemical constituents in Garcinia subelliptica leaves, biflavonoids, and triterpenoids have been investigated. These results indicate the proposed bio-templated adsorbent is practical and eco-friendly for phosphorus sustainability in commercial wastewater treatment.