Enhanced Photocatalytic Activities of RhB Degradation and H2 Evolution from in Situ Formation of the Electrostatic Heterostructure MoS2/NiFe LDH Nanocomposite through the Z-Scheme Mechanism via p-n Heterojunctions

Tailoring atomically local electric field of NiFe layered double hydroxides with Ag dopants to boost oxygen evolution kinetics

The demand for clean energy sources has driven focus towards advanced electrochemical systems. However, the sluggish kinetics of the oxygen evolution reaction (OER) constrain the energy conversion efficiency of relevant devices. Herein, a one-step method is reported to grow oxygen vacancies (Vo) rich NiFeAg layered double hydroxides nanoclusters on carbon cloth (Vo-NiFeAg-LDH/CC) for serving as the self-supporting electrode to catalyze OER. The OER performance of Vo-NiFeAg-LDH/CC has been remarkably enhanced through Ag and Vo co-modification compared with pristine NiFe-LDH, achieving a low Tafel slope of 49.7 mV dec-1 in 1 m KOH solution. Additionally, the current density of Vo-NiFeAg-LDH/CC is 3.23 times higher than that of the state-of-art IrO2 at 2 V under an alkaline flow electrolyzer setup. Theoretical calculations and experimental results collectively demonstrate that Ag dopant and Vo strengthen the O* adsorption with active sites, further promoting the deprotonation step from OH* to O* and accelerating the catalytic reaction. In a word, this work clarifies the structural correlation and synergistic mechanism of Ag dopant and Vo, providing valuable insights for the rational design of catalyst for renewable energy applications.

In Situ Synthesis of Exfoliated Ni(OH)2 Nanosheets and AgNPs-Embedded Functionalized Polyindole-Based Trinary Hybrid Microspheres: A Z-Scheme Photocatalyst for the Sunlight-Driven Degradation of Organic Pollutants with Enhanced Antibacterial Efficacy

Advancing a facile one-pot synthetic approach for the fabrication of a hybrid heterojunction photocatalyst remains a significant challenge in research pursuits. Herein, a microsphere-like trinary hybrid nanocomposite has been synthesized (NH/PIn/MAA/Ag). It comprises exfoliated single- and a few-layered Ni(OH)2 (NH nanosheets), mercaptoacetate-functionalized polyindole (PIn/MAA), and Ag nanoparticles (AgNPs) through an in situ approach. The formation mechanism is based on the exfoliation of stacked Ni(OH)2 multilayers [i.e., Ni(OH)2 microflowers] and stabilization of NH nanosheets through host-guest formation of PIn/MAA, followed by the adsorption-reduction of Ag+ ions in a one-pot reaction at low temperature. Surface morphological analyses of hybrid nanocomposite microspheres have exhibited that highly dense Ni(OH)2 microflowers have been transformed into low-density layered forms (NH nanosheets) within the polymeric platform (PIn/MAA) with deposited AgNPs. An interfacial heterojunction has been developed between the components in the depletion region, leading to an improvement in photocatalytic efficiency through a synergistic effect over the components for charge separation and transfer through the heterojunction interface via solid-state mediator Ag-based Z-scheme charge transfer dynamics. The superior photocatalytic degradation of tetracycline (98.2%) by trinary hybrid microspheres can be attributed to the deteriorated recombination rate of electron-hole pairs with reduced charge transfer resistance of the heterojunction in the photocatalyst, as obvious from photoluminescence, electrochemical impedance spectroscopy, chronoamperometry, and time-resolved photoluminescence (TRPL) analyses. Moreover, the antibacterial properties of microspheres against Bacillus pumilus (Gram-positive) and Escherichia coli (Gram-negative) bacteria have validated their potential as promising materials for the overall purification of aquatic systems.

Electron Accumulation Induced by Electron Injection-Incomplete Discharge on NiFe LDH for Enhanced Oxygen Evolution Reaction

Optimizing the local electronic structure of electrocatalysts can effectively lower the energy barrier of electrochemical reactions, thus enhancing the electrocatalytic activity. However, the intrinsic contribution of the electronic effect is still experimentally unclear. In this work, the electron injection-incomplete discharge approach to achieve the electron accumulation (EA) degree on the nickel-iron layered double hydroxide (NiFe LDH) is proposed, to reveal the intrinsic contribution of EA toward oxygen evolution reaction (OER). Such NiFe LDH with EA effect results in only 262 mV overpotential to reach 50 mA cm-2, which is 51 mV-lower compared with pristine NiFe LDH (313 mV), and reduced Tafel slope of 54.8 mV dec-1 than NiFe LDH (107.5 mV dec-1). Spectroscopy characterizations combined with theoretical calculations confirm that the EA near concomitant Vo can induce a narrower energy gap and lower thermodynamic barrier to enhance OER performance. This study clarifies the mechanism of the EA effect on OER activity, providing a direct electronic structure modulation guideline for effective electrocatalyst design.

Wide-direct-band-gap monolayer carbon nitride CN2: a potential metal-free photocatalyst for overall water splitting

Two dimensional metal-free semiconductors with high work function have attracted extensive research interest in the field of photocatalytic water splitting. Herein, we have proposed a kind of highly stable monolayer carbon nitride CN2 with an anisotropic structure based on first principles density functional theory. The calculations of electronic structure properties, performed using the HSE06 functional, indicate that monolayer CN2 has a wide direct band gap of 2.836 eV and a high work function of 6.54 eV. And the suitable band edge alignment, high electron mobility (∼103 cm2 V-1 s-1) and visible-light optical absorption suggest that monolayer CN2 has potential on visible-light photocatalytic water splitting at pH ranging from 0 to 14. Moreover, we have observed that uniaxial strain can effectively control the electronic structure properties and optical absorption of monolayer CN2, which can further improve its solar to hydrogen efficiency from 9.6% to 16.02% under 5% uniaxial tension strain along the Y direction. Our calculations have not only proposed a new type of potential metal-free photocatalyst for water splitting but also provided a functional part with high work function for type-I and scheme-Z heterojunction applied in photocatalytic water splitting.

Leaflet-heterostructures by MWCNT self-assembly following electrospinning

Electrospinning of nanocarbons such as graphene and carbon nanotubes typically produces mats composed of one-dimensional fibers where the carrier polymer encapsulates the nanocarbons. Recently it was found that decreasing the amount of carrier polymer in approaching the electrospinning-electrospray boundary for graphene suspensions resulted in retention of the graphene two-dimensional anisotropy with one-dimensional carrier polymer fibers connecting flakes. We explored a similar decrease in carrier polymer in MWCNT suspensions to investigate the network topology that might ensue. Unexpectedly, two-dimensional leaflet meso-networks were obtained wherein the leaflets comprise laterally aligned MWCNTs one to several nanotubes thick. A mechanism based on capillary force-driven MWCNT self-assembly activated by menisci formed during drying of electrospun fibers is presented. Such materials offer new approaches to producing high surface-area coatings for catalytic and energy applications and suggest ways of formulating two-dimensional MWCNT assemblies in metal foams and other open-cell porous materials.

Simultaneous Efficient Photocatalytic Hydrogen Evolution and Degradation of Dye Wastewater without Cocatalysts and Sacrificial Agents Based on g-C3N5 and Hybridized Ni-MOF Derivative-CdS-DETA

Inspired by energy conversion and waste reuse, hybridized Ni-MOF derivative-CdS-DETA/g-C3N5, a type-II heterojunction photocatalyst, is synthesized by a hydrothermal method for simultaneous and highly efficient photocatalytic degradation and hydrogen evolution in dye wastewater. Without the addition of cocatalysts and sacrificial agents, the optimal MOF-CD(2)/CN5 (i.e. Ni-MOF derivative-CdS-DETA (20 wt.%)/g-C3N5) exhibit good bifunctional catalytic activity, with a H2 evolution rate of 2974.4 µmol g-1 h-1 during the degradation of rhodamine B (RhB), and a removal rate of 99.97% for RhB. In the process of H2-evolution-only, triethanolamine is used as a sacrificial agent, exhibiting a high H2 evolution rate (19663.1 µmol g-1 h-1) in the absence of a cocatalyst, and outperforming most similar related materials (such as MOF/g-C3N5, MOF-CdS, CdS/g-C3N5). With the help of type-II heterojunction, holes are scavenged for the oxidative degradation of RhB, and electrons are used in the decomposition of water for H2 evolution during illumination. This work opens a new path for photocatalysts with dual functions of simultaneous efficient degradation and hydrogen evolution.

Hydrothermally Synthesized ZnCr- and NiCr-Layered Double Hydroxides as Hydrogen Evolution Photocatalysts

The layered double hydroxides (LDHs) of transition metals are of great interest as building blocks for the creation of composite photocatalytic materials for hydrogen production, environmental remediation and other applications. However, the synthesis of most LDHs is reported only by the conventional coprecipitation method, which makes it difficult to control the catalyst's crystallinity. In the present study, ZnCr- and NiCr-LDHs have been successfully prepared using a facile hydrothermal approach. Varying the hydrothermal synthesis conditions allowed us to obtain target products with a controllable crystallite size in the range of 2-26 nm and a specific surface area of 45-83 m2∙g-1. The LDHs synthesized were investigated as photocatalysts of hydrogen generation from aqueous methanol. It was revealed that the photocatalytic activity of ZnCr-LDH samples grows monotonically with the increase in their average crystallite size, while that of NiCr-LDH ones reaches a maximum with intermediate-sized crystallites and then decreases due to the specific surface area reduction. The concentration dependence of the hydrogen evolution activity is generally consistent with the standard Langmuir-Hinshelwood model for heterogeneous catalysis. At a methanol content of 50 mol. %, the rate of hydrogen generation over ZnCr- and NiCr-LDHs reaches 88 and 41 μmol∙h-1∙g-1, respectively. The hydrothermally synthesized LDHs with enhanced crystallinity may be of interest for further fabrication of their nanosheets being promising components of new composite photocatalysts.

Recent progress in ZnCr and NiCr layered double hydroxides and based photocatalysts for water treatment and clean energy production

In pursuit of advancing photocatalysts for superior performance in water treatment and clean energy generation, researchers are increasingly focusing on layered double hydroxides (LDHs) which have garnered significant attention due to their customizable properties, morphologies, distinctive 2D layered structure and flexible options for modifying anions and cations. No review has previously delved specifically into ZnCr and NiCr LDH-based photocatalysts and therefore, this review highlights the recent surge in ZnCr and NiCr-based LDHs as potential photocatalysts for their applications in water purification and renewable energy generation. The structural and fundamental characteristics of layered double hydroxides and especially ZnCr-LDHs and NiCr-LDHs are outlined. Further, the various synthesis techniques for the preparation of ZnCr-LDHs, NiCr-LDHs and their composite and heterostructure materials have been briefly discussed. The applicability of ZnCr-LDH and NiCr-LDH based photocatalysts in tackling significant issues in water treatment and sustainable energy generation is the main emphasis of this review. It focuses on photocatalytic degradation of organic pollutants in wastewater, elucidating the principles and advancements for enhancing the efficiency of these materials. It also explores their role in H2 production through water splitting, conversion of CO2 into valuable fuels and NH3 synthesis from N2, shedding light on their potential for clean energy solutions. The insights presented herein offer valuable guidance for researchers working towards sustainable solutions for environmental remediation and renewable energy generation.

Heterostructured grafting of NiFe-layered double hydroxide@TiO2 for boosting photoelectrochemical cathodic protection

Accelerating the oxidation process at photoanode-electrolyte interfaces can prolong the lifetime of photoexcited electrons and improve the efficiency of photoelectrochemical cathodic protection (PECCP) systems without relying on hole scavengers. However, the systematic design of precisely structured heterostructures for efficient photoanodes remains challenging. Here we meticulously engineered a type-II heterostructure featuring precise spatial organization, wherein NiFe-layered double hydroxide nanosheets (NiFe-LDH NSs) were assembled onto annealed TiO2 nanorod arrays (ATNAs), demonstrating their effectiveness in achieving efficient PECCP. The interfacial electronic coupling and appropriate energy alignment between the NiFe-LDH NSs and ATNAs allowed rapid hole extraction from the ATNAs to the NiFe-LDH NSs. Furthermore, the uniform distribution of the NiFe-LDH NSs on top of ATNAs drastically reduced the overpotential of oxygen evolution reactions (OER) from 370 to 200 mV and Tafel slope from 162 to 56 mV dec-1, leading to significantly improved cathodic protection of 304 stainless steel (SS) under extended illumination and interesting post-illumination protection. In addition, with the increase of testing cycles, the as-prepared NiFe-LDH NSs@ATNAs demonstrated a progressively enhanced cathodic protection potential from 0.15 to 0.13 V vs. RHE over 50 cycles. These findings provide important guidelines for the design of future high-efficiency green metal protection through rational photoanode design.

Preparation, characterization, and photocatalytic performance of a PVDF/cellulose membrane modified with nano Fe3O4 for removal of methylene blue using RSM under visible light

In this work, a polymeric membrane-based polyvinylidene fluoride coated with cellulose and loaded with iron oxide nanoparticles (PVDF/cellulose/Fe3O4) was synthesized and was characterized using FESEM, XRD, AFM, and contact angle measurements. The activity and modification of the PVDF/cellulose/Fe3O4 membrane under visible light for the removal of methylene blue were studied using the central composite design. The effect of influential variables such as pH, methylene blue concentration, amount of Fe3O4 in the membrane, and irradiation time on MB removal was investigated. Analysis of variance was used to determine the significance of experimental factors and their interactions. About 72.5% methylene blue removal using the PVDF/cellulose/Fe3O4 membrane under visible light was achieved at optimum conditions of a pH of 9, methylene blue concentration of 600 mg L-1, Fe3O4 amount of 0.03 g, and irradiation time of 117 min. Finally, results confirmed that the proposed membrane has good performance for methylene blue removal under visible light.

Recent progress on bismuth-based light-triggered antibacterial nanocomposites: Synthesis, characterization, optical properties and bactericidal applications

Bacterial infections pose a seriously threat to the safety of the environment and human health. In particular, the emergence of drug-resistant pathogens as a result of antibiotic abuse and high trauma risk has rendered conventional therapeutic techniques insufficient for treating infections by these so-called "superbugs". Therefore, there is an urgent need to develop highly efficient and environmentally-friendly antimicrobial agents. Bismuth-based nanomaterials with unique structures and physicochemical characteristics have attracted considerable attention as promising antimicrobial candidates, with many demonstratingoutstanding antibacterial effects upon being triggered by broad-spectrum light. These nanomaterials have also exhibited satisfactory energy band gaps and electronic density distribution with improved photonic properties for extensive and comprehensive applications after being modified through various engineering methods. This review summarizes the latest research progress made on bismuth-based nanomaterials with different morphologies, structures and compositions as well as the different methods used for their synthesis to meet their rapidly increasing demand, especially for antibacterial applications. Moreover, the future prospects and challenges regarding the application of these nanomaterials are discussed. The aim of this review is to stimulate interest in the development and experimental transformation of novel bismuth-based nanomaterials to expand the arsenal of effective antimicrobials.

Discerning the catalytic treatment of cationic dye wastewater in photoreactor comprising ternary (Co3+/Co2+)-embedded SnO2/ZnFe2O4 composite sensitive toward ultra-violet illumination

Herein, magnetic (Co3+/Co2+)-integrated SnO2, SnO2/ZnFe2O4, and ZnFe2O4 composites have been prepared from triply distilled water and 30% of isopropanol in the water medium. The phase evolution, microstructure, and magnetism were investigated successfully and tested for cationic dye wastewater degradation containing Rhodamine 6G and Methylene Blue under ultra-violet irradiation. Composite spheres are attributed to efficient heterojunction interfaces between ZnFe2O4 and SnO2 semiconductors with the support of (Co3+/Co2+) nanoparticles. The results provide a simple, low-cost, environmentally friendly, and scalable method of ternary composites to degrade mixed dyes. Co3+/Co2+-implanted SnO2/ZnFe2O4 offered narrowed bandgap energy, more light absorption, diminishing electron-hole recombination, and more charge carriers toward cationic dye wastewater than the binary components. The rate constant of Rhodamine 6G degradation was observed at 0.0237 min-1, and Methylene Blue degradation was observed at 0.0187 min-1 at 90 min under UV (λ = 365 nm) irradiation. Capturing studies of various organic reactive species and mechanisms of composites was also proposed in detail.

Progress in layered double hydroxides (LDHs): Synthesis and application in adsorption, catalysis and photoreduction

Layered double hydroxides (LDHs), also known as anionic clays, have attracted significant attention in energy and environmental applications due to their exceptional physicochemical properties. These materials possess a unique structure with surface hydroxyl groups, tunable properties, and high stability, making them highly desirable. In this review, the synthesis and functionalization of LDHs have been explored including co-precipitation and hydrothermal methods. Furthermore, extensive research on LDH application in toxic pollutant removal has shown that modifying or functionalizing LDHs using materials such as activated carbon, polymers, and inorganics is crucial for achieving efficient pollutant adsorption, improved cyclic performance, as well as effective catalytic oxidation of organics and photoreduction. This study offers a comprehensive overview of the progress made in the field of LDHs and LDH-based composites for water and wastewater treatment. It critically discusses and explains both direct and indirect synthesis and modification techniques, highlighting their advantages and disadvantages. Additionally, this review critically discusses and explains the potential of LDH-based composites as absorbents. Importantly, it focuses on the capability of LDH and LDH-based composites in heterogeneous catalysis, including the Fenton reaction, Fenton-like reactions, photocatalysis, and photoreduction, for the removal of organic dyes, organic micropollutants, and heavy metals. The mechanisms involved in pollutant removal, such as adsorption, electrostatic interaction, complexation, and degradation, are thoroughly explained. Finally, this study outlines future research directions in the field.

Nitrate Reduction by NiFe-LDH/CeO2: Understanding the Synergistic Effect between Dual-Metal Sites and Dual Adsorption

Electrocatalytic nitrate reduction reaction (EC-NITRR) shows a significant advantage for green reuse of the nitrate (NO3-) pollutant. However, the slow diffusion reaction limits the reaction rate in practical EC-NITRR, causing an unsatisfactory ammonia (NH3) yield. In this work, a multifunctional NiFe-LDH/CeO2 with the dual adsorption effect (physisorption and chemisorption) and dual-metal sites (Ce3+ and Fe2+) was fabricated by the electrodeposition method. NiFe-LDH/CeO2 performed an expected ability of enrichment for NO3- through the pseudo-first-order and pseudo-second-order kinetic models, and the polymetallic structure provided abundant sites for effective reaction of NO3-. At-0.6 V vs RHE, the ammonia (NH3) yield of NiFe-LDH/CeO2 reached 335.3 μg h-1 cm-2 and the selectivity of NH3 was 24.2 times that of NO2-. The nitrogen source of NH3 was confirmed by 15NO3- isotopic labeling. Therefore, this work achieved the recycling of the NO3- pollutant by synergy of enrichment and catalysis, providing an alternative approach for the recovery of NO3- from wastewater.

Water-stable perovskite CsPb2Br5/CdSe quantum dot-based photoelectrochemical sensors for the sensitive determination of dopamine

A heterojunction of CdSe quantum dots in situ grown on the perovskite CsPb2Br5 (CsPb2Br5/CdSe) for water-stable photoelectrochemical (PEC) sensing was simply synthesized using the hot-injection method. Due to the inherent built-in electric field and the matching band structure between CsPb2Br5 and CdSe, the CsPb2Br5/CdSe p-n heterojunction demonstrates enhanced photoelectrochemical properties. Accelerated interfacial charge transfer and increased electron-hole pair separation enable hydrolysis-resistant CsPb2Br5/CdSe sensors to exhibit heightened sensitivity with an ultra-low detection limit (0.0124 μM) and a wide linear range (0.4-303.9 μM) in subsequent dopamine detection. Moreover, the CsPb2Br5/CdSe sensors show excellent anti-interference ability, as well as remarkable stability and reproducibility in water solvent. It is noteworthy that this work is conducted in an aqueous environment, which provides an inspiring and convenient way for photoelectric and photoelectrocatalysis applications based on water-resistant perovskites.

Integration of ohmic junction and step-scheme heterojunction for enhanced photocatalysis

A novel and efficient photocatalyst, Cu2WS4/MoS2-Au plasmonic Step-scheme (S-scheme) heterojunction, was constructed for the first time and applied to remove environmental pollutants. Among all the prepared photocatalysts, the. Cu2WS4/MoS2-Au-5 exhibited the highest catalytic activity with an 89.1% reduction efficiency for Cr6+ and a 98.7% oxidation efficiency for Benzophenone-1 (BP-1) under visible light irradiation. The Cu2WS4/MoS2-Au photocatalyst exhibits stable performance and efficient photocatalytic activity due to effective charge separation, enhanced light absorption from localized surface plasmon resonance (LSPR) of gold nanoparticles, and the formation of an S-scheme heterojunction with strong oxidation-reduction capabilities. In addition, through analysis of experiments and theoretical calculations, it is speculated that the Cu2WS4/MoS2-Au follows a typical S-scheme photogenerated carrier transferring mechanism, which is verified by the finite difference time domain simulation, the free radical quenching experiments, the electron paramagnetic resonance analysis and the simulated charge density distribution. More importantly, the simulations of the work function and charge density distribution confirm the built-in electric field and the ohmic junction have been established at the interfaces between the Cu2WS4 and MoS2 (Cu2WS4/MoS2) as well as the interface between MoS2 and Au (MoS2-Au), respectively. The built-in electric field and ohmic junction enable efficient separation of photogenerated electrons and holes, ensuring the superior catalytic oxidation and reduction activities of the Cu2WS4/MoS2-Au photocatalyst. Finally, we propose a photocatalytic mechanism for the Cu2WS4/MoS2-Au plasmonic S-scheme heterojunction based on experimental results and simulated calculations. The research results of this study are significance for the development of the plasmonic S-scheme photocatalytic system.

Enhanced generation of reactive radicals and electrocatalytic oxidation of levofloxacin using a trimetallic CuFeV layered double hydroxide-containing electrode

In Electro-Fenton (EF) processes, the use of iron as a catalyst under acidic conditions results in increased costs and potential secondary pollution. To address these issues, we developed a CuFeV layered double hydroxide (LDH) coating on graphite felt (GF) (CuFeV LDH@GF) that offers an effective performance across a broad pH range without causing metal pollution. The CuFeV LDH@GF cathode exhibited a good oxygen reduction performance, high stability, and an efficient removal of levofloxacin (LEV) over a wide pH range (pH = 3-10). The simultaneous presence of Cu2+/Cu3+, Fe2+/Fe3+, and V4+/V5+ redox pairs played a crucial role in facilitating interfacial electron transfer, thereby enhancing the production and subsequent activation of H2O2 within the system. The apparent rate constant (kapp) of LEV removal under neutral conditions with the CuFeV LDH@GF electrode was more than twice that of the raw GF electrode. This improvement can be attributed to the CuFeV LDH coating, which increased the generation of hydroxyl radicals (•OH) from 0.64 to 1.27 mM. Importantly, the CuFeV LDH@GF electrode maintained its efficiency and stability even after 10 reuse cycles. Additionally, GC-MS analyses revealed the degradation of intermediate compounds, which included cyclic and aliphatic compounds. This study provides significant insights into the synergistic effects of trimetallic LDHs, contributing to the development of high-performance cathodes.

S-Scheme ZIF-67/CuFe-LDH Heterojunction for High-Performance Photocatalytic H2 Evolution and CO2 to MeOH Production

The S-scheme heterojunction photocatalyst holds potential for better photocatalysis owing to its capacity to broaden the light absorption range, ease electron-hole separation, extend the charge carrier lifespan, and maximize the redox ability. In this study, we integrate zeolitic imidazolate frameworks (ZIFs-67) with the CuFe-LDH composite, offering a straightforward approach towards creating a novel hybrid nanostructure, enabling remarkable performance in both photocatalytic hydrogen (H2) evolution and carbon dioxide (CO2) to methanol (MeOH) conversion. The ZIF-67/CuFe-LDH photocatalyst exhibits an enhanced photocatalytic hydrogen evolution rate of 7.4 mmol g-1 h-1 and an AQY of 4.8%. The superior activity of CO2 reduction to MeOH generation was 227 μmol g-1 h-1 and an AQY of 5.1%, and it still exhibited superior activity after continuously working for 4 runs with nearly negligible decay in activity. The combined spectroscopic analysis, electrochemical study, and computational data strongly demonstrate that this hybrid material integrates the advantageous properties of the individual ZIF-67 and CuFe-LDH exhibiting distinguished photon harvesting, suppression of the photoinduced electron-hole recombination kinetics, extended lifetime, and efficient charge transfer, subsequently boosting higher photocatalytic activities.

GQD@NiFe-LDH Nanosheets for Photocatalytic Activity towards Textile Dye Degradation via Lattice Contraction

The functionalized NiFe-LDH with photosensitized GQDs were synthesized through the hydrothermal route by differing the amount of GQDs solution and studied its efficacy towards the mineralization of textile dyes under visible light. The synthesized samples were characterized by XRD, FESEM, HRTEM, DRUV-Vis, RAMAN, XPS, and BET. The combined effect of the hexagonal carbon lattice in GQD and open layered porous structure of NiFe-LDH nanosheets results in the contraction of the lattice. Different reactive and conventional dyes were taken as representative dyes to evaluate the activity of the as-synthesized photocatalysts. The enhanced electron absorption/donor effect between GQDs and NiFe-LDH, and the growth of oxygen-bridged Ni/Fe-C moieties enable the composite to exhibit better photocatalytic activity. Both photocatalytic activity and characterization results confirmed that the GQD@NiFe-LDH nanocomposite heterostructure synthesized at 160 °C by taking 10 mL of GQDs aqueous solution named GNFLDH10 has a higher degree of crystallinity and has the best photocatalytic efficiency compared to other reported visible light catalysts. Specifically, the above optimized GQD@NiFe-LDH photocatalyst is capable of photo-mineralizing 50 ppm of Reactive Green in 20 min, Reactive Red in 20 min, and Congo Red in 25 min respectively following a direct Z-scheme mechanism with substantial reusability.

Preparation of site-specific Z-scheme g-C3N4/PAN/PANI@LaFeO3 cable nanofiber membranes by coaxial electrospinning: Enhancing filtration and photocatalysis performance

The coaxial electrospinning method for preparation of g-C₃N₄/polyacrylonitrile (PAN)/polyaniline (PANI)@LaFeO₃ cable fiber membrane (PC@PL) was designed for adsorption-filtration-photodegradation of pollutants. A series of characterization results show that LaFeO₃ and g-C₃N₄ nanoparticles (NPs) are respectively loaded in the inner and outer layers of PAN/PANI composite fibers to construct the site-specific Z-type heterojunction system with spatially separated morphologies. The PANI in cable not only possesses abundant exposed amino/imino functional groups for adsorption of contaminant molecules but also due to the excellent electrical conductivity works as a redox medium for collecting and consuming the electrons and holes from LaFeO₃ and g-C₃N₄, which can efficiently promote photo-generated charge carriers separation and improve the catalytic performance. Further investigations demonstrate that as a photo-Fenton catalyst LaFeO₃ in PC@PL catalyzes/activates the H₂O₂ generated in situ by LaFeO₃/g-C₃N₄, further enhancing the decontamination efficiency of the PC@PL. The porous, hydrophilic, antifouling, flexible and reusable properties of the PC@PL membrane significantly enhance the mass transfer efficiency of reactants by filtration effect and increase the amount of dissolved oxygen, thus producing massive •OH for degradation of pollutants, which maintains the water flux (1184 L m^-2. h^-1 (LMH)) and the rejection rate (98.5%). Profiting from its unique synergistic effect of adsorption, photo-Fenton and filtration, PC@PL exhibits wonderful self-cleaning performance and distinguished removal rate for methylene blue (97.0%), methyl violet (94.3%), ciprofloxacin (87.6%) and acetamiprid (88.9%) within 75 min, disinfection (100% Escherichia coli (E. coli) and 80% Staphylococcus aureus (S.aureus) inactivation)) and excellent cycle stability.

Insight into the In-Situ Encapsulation-Reassembly Strategy To Fabricate PW12@NiCo-LDH Acid-Base Bifunctional Catalysts

Acid-base bifunctional catalysts have attracted increasing attention due to the improved overall efficiency of synthetic reactions. Herein, we reported the successful fabrication of a PW₁₂@NiCo-LDH acid-base bifunctional catalyst by using the in-situ encapsulation-reassembly strategy. The evolution process of morphology and structure was monitored carefully by various time-dependent characterizations. X-ray absorption fine structure (XAFS) and density functional theory (DFT) calculations demonstrated that the terminal oxygen of PW₁₂ in PW₁₂@NiCo-LDH preferred to assemble with the oxygen vacancies on NiCo-LDH. When applied for deacetalization-Knoevenagel condensation, the PW₁₂@NiCo-LDH displayed >99% conversion of benzaldehyde dimethyl acetal (BDMA) and >99% yield of ethyl α-cyanocinnamate (ECC). Moreover, PW₁₂@NiCo-LDH can be recycled at least 10 cycles without obvious structural change, which can be attributed to the confinement of PW₁₂ into the NiCo-LDH nanocage. Such excellent catalytic activity of PW₁₂@NiCo-LDH was benefited from the short mass transfer pathway between acid sites and base sites, which was caused by the stable assembly between PW₁₂ and NiCo-LDH.

Nanoarchitecture of a Ti3C2@TiO2 Hybrid for Photocatalytic Antibiotic Degradation and Hydrogen Evolution: Stability, Kinetics, and Mechanistic Insights

Designing of a visible-light-driven semiconductor-based heterojunction with suitable band alignment and well-defined interfacial contact is considered to be an effective strategy for the transformation of solar-to-chemical energy and environmental remediation. In this context, MXenes have received tremendous attention in the research community due to their merits of abundant derivatives, elemental composition, excellent metallic conductivity, and surface termination groups. Meanwhile, a facile synthetic strategy for MXene-derived TiO₂ nanocomposites with stable framework and higher photocatalytic activity under visible-light irradiation still remains a challenge for researchers. Herein, we report a novel synthetic strategy of preparing a two-dimensional Ti₃C₂@TiO₂ nanohybrid by a facile reflux method under acidic conditions. In this oxidation reaction, protonation of the hydroxyl terminal group of MXene creates Ti more electrophilic and susceptible to an oxidative nucleophilic addition reaction with the presence of both water and oxygen. The physicochemical properties of the nanohybrid Ti₃C₂@TiO₂ were verified by varieties of characterization techniques. High-resolution transmission electron microscopy and X-ray photoelectron spectroscopy analysis specifically elucidated the intimate interfacial interaction between Ti₃C₂ and TiO₂. The optimized Ti₃C₂@TiO₂-48 h photocatalyst exhibited the highest tetracycline hydrochloride (TCH, 90% in 90 min) degradation efficiency in comparison to pristine TiO₂ with a rate constant (k) of 0.02463 min^-1. The major contribution of ^•O₂^- and ^•OH radicals throughout photocatalytic TCH degradation was confirmed by the trapping experiment. Moreover, the photocatalyst showed the highest hydrogen generation rate of 140.8 μmol h^-1 along with an apparent conversion efficiency of 2.2%. The excellent photocatalytic activity of Ti₃C₂@TiO₂ originated from the superior electrical conductivity of cocatalyst Ti₃C₂, which facilitated spatial photogenerated e^-/h⁺ separation and transfer at the Ti₃C₂ MXene@TiO₂ interface. Overall, this research work will describe a promising protocol of designing MXene-derived photocatalysts toward efficient environmental remediation and wastewater treatment applications.

Indulgent of the physiochemical features of MgCr-LDH nanosheets towards photodegradation process of methylene blue

In the present work, we report the preparatory strategy of MgCr-layered double hydroxide (LDH) nanosheets with 90% degree of delamination by employing a formamide-assisted co-precipitation and mild hydrothermal route for the degradation of methylene blue (MB) under solar light exposure. The as-synthesized MgCr-LDH nanosheets were characterized by assorted characterization techniques such as powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), Raman, thermogravimetric analysis (TGA), N₂ adsorption-desorption measurement, X-ray photoelectron spectroscopy (XPS) and UV-Visible diffused reflectance spectroscopy (UV-DRS). The XRD pattern of MgCr-LDH nanosheets quantified the strain (ε) and dislocation density (δ) of 1.371 lines^-2 m^-4 and 0.5723 lines m^-2 related to the (110) plane with d-spacing value of 1.6169 Ȧ. With a minimum band gap of ∼2.63 eV, the as-synthesized MgCr-LDH nanosheets displayed 90.6% MB photodegradation under the experimental protocols such as catalyst dosage of 30 mg/L, initial MB concentrations of 20 ppm, pH of 7 and time duration of 2 h under solar light exposure. Further, the recyclability test of the photocatalyst signifies material stability up to four successive cycles with 90% retention of MB degradation under sunlight exposure. The superior catalytic performances of the MgCr-LDH nanosheets could be ascertained to the suppression of excitonic recombination and effective light harvestation properties, synergistically contributed by the porous structural aspects via association of uni/multi-lamellar nanosheets, surface defect sites and photoactive Cr³⁺ cations. Additionally, the surface -OH groups of LDH contributed towards the generation of ^•OH radicals for triggering the catalytic performances. This type of work advances the novel ideas for establishing highly potent photocatalysts via synergizing structural and surface properties, paving towards effective wastewater treatment.

Fe-Ce/Layered Double Hydroxide Heterostructures and Their Derived Oxides: Electrochemical Characterization and Light-Driven Catalysis for the Degradation of Phenol from Water

Fe-Ce/layered double hydroxides (LDHs) were synthesized via a facile route by exploiting the "structural memory" of the LDH when the calcined MgAlLDH and ZnAlLDH were reconstructed in the aqueous solutions of FeSO₄/Ce(SO₄)₂. XRD analysis shows the formation of heterostructured catalysts that entangle the structural characteristics of the LDHs with those of Fe₂O₃ and CeO₂. Furthermore, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, TG/DTG, SEM/EDX and TEM results reveal a complex morphology defined by the large nano/microplates of the reconstructed LDHs that are tightly covered with nanoparticles of Fe₂O₃ and CeO₂. Calcination at 850 °C promoted the formation of highly crystallized mixed oxides of Fe₂O₃/CeO₂/ZnO and spinels. The photo-electrochemical behavior of Fe-Ce/LDHs and their derived oxides was studied in a three-electrode photo-electrochemical cell, using linear sweep voltammetry (LSV), Mott-Schottky (M-S) analysis and photo-electrochemical impedance spectroscopy (PEIS) measurements, in dark or under illumination. When tested as novel catalysts for the degradation of phenol from aqueous solutions, the light-driven catalytic heterojunctions of Fe-Ce/LDH and their derived oxides reveal their capabilities to efficiently remove phenol from water, under both UV and solar irradiation.

Adsorption and photodegradation of reactive red 120 with nickel-iron-layered double hydroxide/biochar composites

Layered double hydroxide (LDH) materials were widely applied for adsorption and photodegradation of pollutants for wastewater treatment. New efficient LDH materials with adsorption and photodegradation abilities will be promising candidates for pollutants removal. Hence, a series of NiFe-LDH/biochar (NiFe/BC) were fabricated by the coprecipitation method for synergistic adsorption and photodegradation anionic dyes of reactive red 120 (RR120). The removal experiment showed that the addition of an appropriate amount of biochar into NiFe-LDH enhanced the adsorption capacity and its photocatalytic ability. The optimized NiFe/BC2 composite can remove 88.5 % of RR120 under visible light by adsorption and photocatalysis, which was much better than NiFe-LDH (63.3 %) and biochar (2.6 %). The photodegradation kinetic constant of the NiFe/BC2 composite was 3.1 and 104.8 times that of NiFe-LDH and BC. In addition, active species capture experiments and electron spin resonance (ESR) tests revealed the removal mechanisms of NiFe/BC composites for RR120 removal. This work affords a feasible strategy for preparing LDH-based photocatalyst with excellent adsorption and photocatalytic performance for wastewater treatment.

Degradation of ciprofloxacin by a constitutive g-C3N4/BiOCl heterojunction under a persulfate system

Ciprofloxacin (CIP) is a third-generation quinolone antimicrobial with broad-spectrum antimicrobial activity, and is not fully metabolized in the human body, resulting in more than 70% of CIP being excreted into water as a prodrug. In this study, g-C₃N₄/BiOCl heterojunction structure composites were prepared to study the degradation effect of ciprofloxacin (CIP) under photocatalytic conditions. The results showed that CIP at 10 mg L^-1 was best degraded after 90 min at 0.3 g L^-1 g-C₃N₄/BiOCl-2, pH of 5.8 and PS dosing of 1 mM. The quenching experiments and electron spin resonance spectroscopy (ESR) confirmed that ˙OH, ˙SO₄ ^- and h⁺ played a major role. After the photocatalytic degradation of this reaction system, the biological toxicity of CIP was effectively controlled. This material is stable and the CIP removal rate remained above 80% after four cycles of experiments.

NiFe-Layered Double Hydroxides/Lead-free Cs2AgBiBr6 Perovskite 2D/2D Heterojunction for Photocatalytic CO2 Conversion

Designing of heterojunction photocatalysts with appropriate interfacial contact plays crucial roles in enhancing the interfacial charge transfer/separation. A two-dimensional (2D)/2D face-to-face heterojunction is an ideal option since this architecture with a large contact area can provide abundant reactive centers and promote the interfacial charge transfer/separation between layers. Herein, a novel 2D/2D heterojunction of NiFe-layered double hydroxides (NiFe-LDH)/Cs₂AgBiBr₆ (CABB) was fabricated by electrostatic self-assembly of NiFe-LDH and CABB nanosheets. This unique 2D/2D architecture endowed NiFe-LDH/CABB with a large contact area and a short charge transport distance, assuring remarkable interfacial charge transfer/separation rates. As a result, the 2D/2D NiFe-LDH/CABB heterojunction exhibited significant improvement in photocatalytic CO₂ reduction under visible light than the pristine counterparts. Based on density functional theory calculations and various characterizations, a step scheme charge-transfer mechanism was proposed. This investigation sheds light on the designing and manufacturing of highly efficient 2D/2D heterostructure photocatalysts for artificial photosynthesis.

Synthesis of visible light responsive ZnCoFe layered double hydroxide towards enhanced photocatalytic activity in water treatment

In this study, a ternary layered double hydroxide containing Zn, Co, and Fe transition metals (ZnCoFe LDH) was developed using a co-precipitation procedure. The as-synthesized photocatalyst was evaluated for its performance in the degradation of methylene blue (MB) under visible light irradiation. The effects of various process conditions including photocatalyst dosage, pollutant concentration, pH, lamp distance, and lamp power were investigated. The ZnCoFe LDH achieved approximately 74% photodegradation efficiency owing to the narrow bandgap of 2.14 eV. The Langmuir-Hinselwood rate constants were calculated as 1.17 min^-1 and 3.55 min^-1 for photolysis by LED lamp alone and for photocatalysis by LED/ZnCoFe LDH, respectively. The photocatalytic ability of the LDH was attributed to the generation of radical species like ^•OH and O₂^•-. The photocatalytic degradation intermediates of MB were determined by GC-MS analysis. The catalyst retained its performance throughout seven reuse cycles with only a 4.17% reduction in removal efficiency. The energy per order E_EO of the ZnCoFe/LED process in 180 min treatment time was determined as 5.41 kWh.m^-3. order^-1. This study shows that ZnCoFe LDH has sufficient activity and photostability for long-term application in photocatalytic water treatment.

Heterostructured α-Bi2O3/BiOCl Nanosheet for Photocatalytic Applications

Photocatalytic degradation of organic pollutants in wastewater is recognized as a promising technology. However, photocatalyst Bi₂O₃ responds to visible light and suffers from low quantum yield. In this study, the α-Bi₂O₃ was synthetized and used for removing Cl^- in acidic solutions to transform BiOCl. A heterostructured α-Bi₂O₃/BiOCl nanosheet can be fabricated by coupling Bi₂O₃ (narrow band gap) with layered BiOCl (rapid photoelectron transmission). During the degradation of Rhodamine B (RhB), the Bi₂O₃/BiOCl composite material presented excellent photocatalytic activity. Under visible light irradiation for 60 min, the Bi₂O₃/BiOCl photocatalyst delivered a superior removal rate of 99.9%, which was much higher than pristine Bi₂O₃ (36.0%) and BiOCl (74.4%). Radical quenching experiments and electron spin resonance spectra further confirmed the dominant effect of electron holes h⁺ and superoxide radical anions ·O₂^- for the photodegradation process. This work develops a green strategy to synthesize a high-performance photocatalyst for organic dye degradation.

Layered Double Hydroxides for Photo(electro)catalytic Applications: A Mini Review

Chemical energy conversion strategies by photocatalysis and electrocatalysis are promising approaches to alleviating our energy shortages and environmental issues. Due to the 2D layer structure, adjustable composition, unique thermal decomposition and memory properties, abundant surface hydroxyl, and low cost, layered double hydroxides (LDHs) have attracted extensive attention in electrocatalysis, photocatalysis, and photoelectrocatalysis. This review summarizes the main structural characteristics of LDHs, including tunable composition, thermal decomposition and memory properties, delaminated layer, and surface hydroxyl. Next, the influences of the structural characteristics on the photo(electro)catalytic process are briefly introduced to understand the structure-performance correlations of LDHs materials. Recent progress and advances of LDHs in photocatalysis and photoelectrocatalysis applications are summarized. Finally, the challenges and future development of LDHs are prospected from the aspect of structural design and exploring structure-activity relationships in the photo(electro)catalysis applications.

Dual-quantum-dots heterostructure with confined active interface for promoted photocatalytic NO abatement

Constructing heterostructure is an effective way to fabricate advanced photocatalysts. However, the catalytic performance of typical common multi-dimensional bulk heterostructure still suffers from the limited active interface and inefficient carrier migration. Herein, we successfully synthesize the SnO₂/Cs₃Bi₂I₉ dual-quantum-dots nanoheterostructure (labeled as SCX, X = 1, 2, 3) for efficiently and stably photocatalytic NO removal under visible light irradiation. The NO removal rate of SC2 is almost 8 and 17 times higher than that of the single SnO₂ and Cs₃Bi₂I₉, respectively. Moreover, the SC2 photocatalyst shows only 3 % attenuation after five consecutive cycles, demonstrating good photocatalytic stability. Systematic experimental characterization and theoretical density functional theory calculations revealed that the high activity and stability of SCX originated from the efficient charge transfer at the confined interface between SnO₂ and Cs₃Bi₂I₉ quantum dots. This work provides a new perspective for constructing innovative dual-quantum-dots nanoheterostructure and assesses their potential in photocatalytic environmental applications.

Outlook on bismuth-based photocatalysts for environmental applications: A specific emphasis on Z-scheme mechanisms

Semiconductor photocatalysis is thought to be a viable solution for addressing the growing problem of environmental pollution. Bismuth (Bi) metal oxides can function as a direct plasmonic photocatalyst or cocatalyst to accelerate the photogenerated charge separation and thus improve their photocatalytic activity. Hence, Bi-based photocatalysts have received a lot of attention due to their extensive environmental applications, including pollutant remediation and energy concepts. Massive efforts have been undertaken in the recent decade to find superior Bi-metal oxides (Bi₂XO_6, X = MO, W, or Cr) and to uncover the corresponding photocatalytic reaction mechanism for the degradation of organic contaminants in water. Herein, the unique crystalline and electronic properties and main synthesis methods, as well as the major Bi-Based direct Z-scheme photocatalysts, are timely discussed and summarized in their usage in water treatment. Besides, the impact of Bi₂XO₆ in energy storage devices and solar energy conversion is reviewed as an energy application. Finally, the future development and challenges of Z-scheme-based Bi₂XO₆ photocatalysts are briefly explored, summarized, and forecasted.

Enhanced visible light photocatalytic hydrogen production over poly(dibenzothiophene-S,S-dioxide)-based heterostructures decorated by Earth-abundant layered double hydroxides

Layered double hydroxides (LDHs) have emerged as one of the promising catalyst substitutes to noble metals in photocatalytic water splitting due to their unique optoelectronic properties. Herein, a series of novel PSO@NiFeLDH composites have been designed and synthesized to investigate photocatalytic performance. Various physicochemical techniques characterized their structural, nanomorphological, and optical properties. These results demonstrated the existence of NiFeLDH particles on the surface of PSO and the strong interaction between NiFeLDH and PSO. The photocatalytic performance was much increased in the case of PSO@NiFeLDH as compared to that of Pt-modified PSO because of the synergistic effect between PSO and NiFeLDH. Remarkably, PSO@NiFeLDH-15 exhibits the highest photocatalytic activity with a rate of 52.8 mmol h^-1 g^-1 at an optimal content without a Pt cocatalyst under visible light irradiation.

Copper-doped carbon dots with enhanced Fenton reaction activity for rhodamine B degradation

The Fenton reaction has attracted extensive attention due to its potential to be a highly efficient and environmentally friendly wastewater treatment technology. Noble copper-doped carbon dots (CuCDs) are prepared through a simple one-step hydrothermal method with 3,4-dihydroxyhydrocinnamic acid, 2,2'-(ethylenedioxy)bis(ethylamine) and copper chloride, endowing the Fenton reaction with enhanced catalytic activity for rhodamine B (RhB) degradation. The effects of the concentration of CuCDs, temperature, pH, oxygen (O2), metal ions and polymers on the catalytic activity of CuCDs are investigated. It is worth noting that electron transfer happening on the surface of CuCDs plays a vital role in the RhB degradation process. As evidenced by radical scavenger experiments and electron spin resonance (ESR) studies, CuCDs significantly boost the formation of hydroxyl radicals (˙OH) and singlet oxygen (1O2), facilitating the Fenton reaction for RhB degradation. Due to the strong oxidation of ROS generated by the Fe2+ + H2O2 + CuCD system, RhB degradation may involve the cleavage of the chromophore aromatic ring and the de-ethylation process. Additionally, the toxicity of RhB degradation filtrates is assessed in vitro and in vivo. The as-prepared CuCDs may be promising catalytic agents for the enhancement of the Fenton reaction.

Superlative photoelectrochemical properties of 3D MgCr-LDH nanoparticles influencing towards photoinduced water splitting reactions

In the present work, we report the synthesis of single system three-dimensional (3D) open porous structure of MgCr-LDH nanoparticles in a substrate-free path by using one-step formamide assisted hydrothermal reaction followed by visible light irradiation for significant photoelectrochemical (PEC) properties that manifest towards photocatalytic H₂ and O₂ production. The as-prepared nanostructured materials were characterized by various physico-chemical characterization techniques. Moreover, this unique synthetic approach produces 3D open porous network structure of MgCr-LDH nanoparticles, which were formed by stacking of numerous 2D nanosheets, for effective light harvestation, easy electronic channelization and unveil superlative PEC properties, including high current density (6.9 mA/cm²), small Tafel slope of 82 mV/decade, smallest arc of the Nyquist plot (59.1 Ω cm⁻²) and photostability of 6000 s for boosting water splitting activity. In addition, such perfectly self-stacked 2D nanosheets in 3D MgCr-LDH possess more surface active defect sites as enriched 50% oxygen vacancy resulting a good contact surface within the structure for effective light absorption along with easy electron and hole separation, which facilitates the adsorption of protons and intermediate for water oxidation. Additionally, the Cr³⁺ as dopant pull up the electrons from water oxidation intermediates, thereby displaying superior photocatalytic H₂ and O₂ production activity of 1315 μmol/h and 579 μmol/h, respectively. Therefore, the open 3D morphological aspects of MgCr-LDH nanoparticles with porous network structure and high surface area possess more surface defect sites for electron channelization and identified as distinct novel features of this kind of materials for triggering significant PEC properties, along with robustly enhance the photocatalytic water splitting performances.

Rationally designed Ti3C2/N, S-TiO2/g-C3N4 ternary heterostructure with spatial charge separation for enhanced photocatalytic hydrogen evolution

The charge separation and transfer are the major issues dominating the under-laying energy conversion mechanism for photocatalytic system. Construction of semiconductor-based heterojunction system considered to be viable option for boosting the spatial charge separation and transfer in the photocatalytic water splitting system. Here, we design a ternary heterojunction of Ti₃C₂/N, S-TiO₂/g-C₃N₄ by thermal annealing and ultrasonic assisted impregnation method having a well-designed n-n heterojunction and noble metal free Schottky junction for adequate hydrogen evolution. The optimal content of 4 wt% Ti₃C₂ on N, S-TiO₂/g-C₃N₄ (4-TC/NST/CN) exhibit the highest rate of hydrogen generation 495.06μ mol h^-1 which is 3.1, 4.1 and 1.6 fold higher than the pristine N, S doped-TiO₂, g-C₃N₄ and binary hybrid (N, S doped-TiO₂/g-C₃N₄) respectively, with 7% apparent conversion efficiency (ACE). The increment in the activity is described to the robust photogenerated carrier separation and double charge transfer channels because of the formation of dual heterojunction (n-n heterojunction and Schottky junction). XRD and Raman results revealed the occupancy of Ti₃C₂ in the heterojunction due to the strong interaction between Ti₃C_2, with N, S doped-TiO₂ and g-C₃N₄. The HRTEM analysis confirmed the formation of close interfacial junction between the Ti₃C₂, N, S doped-TiO₂ and g-C₃N₄. Moreover, the higher photocurrent, low PL intensity and lower impedance arc suggested the lower charge carrier recombination rate in 4-TC/NST/CN heterojunction. This work represents a significant development to establish a sound foundation for future design of MXene-based ternary hybrid system towards significant charge carrier separation and transfer for H₂ production activity.

High-Efficiency Photocatalytic Ammonia Synthesis by Facet Orientation-Supported Heterojunction Cu2O@BiOCl[100] Boosted by Double Built-In Electric Fields

In this work, the advantages of in situ loading, heterojunction construction, and facet regulation were integrated based on the poly-facet-exposed BiOCl single crystal, and a facet-oriented supported heterojunction of Cu₂O and BiOCl was fabricated (Cu₂O@BiOCl[100]). The photocatalytic nitrogen reduction reaction (pNRR) activity of Cu₂O@BiOCl[100] was as high as 181.9 μmol·g^-1·h^-1, which is 4.09, 7.13, and 1.83 times that of Cu₂O, BiOCl, and Cu₂O@BiOCl-ran (Cu₂O randomly supported on BiOCl). Combined with the results of the photodeposition experiment, X-ray photoelectron spectroscopy characterization, and DFT calculation, the mechanism of Cu₂O@BiOCl[100] for pNRR was discussed. When Cu₂O directionally loaded on the [100] facet of BiOCl, electrons generated by Cu₂O will be transmitted to the [100] facet of BiOCl through Z-scheme electron transmission. Due to the directional separation characteristics of charge in BiOCl, the electrons transmitted from Cu₂O are enriched on the [001] facet of BiOCl, which will together with the original electrons generated by pristine BiOCl act on pNRR, thus greatly improving the activity of photocatalytic ammonia synthesis. Thus, a new construction scheme of biphasic semiconductor heterojunction was proposed, which provides a reference research idea for designing and synthesizing high-performance photocatalysts for nitrogen reduction.

A facile solvothermal syntheses of NiFe layered double hydroxide-Bi2MoO6 heterostructure/reduced graphene oxide with efficient photodegradation for tetracycline

A heterojunction of NiFe layered double hydroxide (NiFe LDH)-Bi₂MoO₆ (BMO) loaded on reduced graphene oxide (RGO) sheets was synthesized via an eco-friendly solvothermal reaction. The structural characterization shows that NiFe LDH-BMO heterojunctions are well-distributed on the surface of silk-like transparent RGO sheets. The modification of BMO by NiFe LDH and RGO greatly enhances the photocatalytic performance of BMO for degradation of tetracycline (TC) under visible light. The photocatalyst prepared with 3 wt% RGO shows the highest activity and cycle stability. TC can be completely removed in 80 min, which is about 8.7 times that pure BMO, and showing excellent reusability even after five cycles. The excellent enhancement of photocatalytic performance of NiFe LDH-BMO/RGO composite is attributed to the unique sheet-on-sheet hierarchical heterostructure combined with RGO sheets, facilitating the visible light absorption and photogenerated charge carriers separation.