Highly Conductive Doped Hybrid Carbon Nanotube-Graphene Wires

Fabrication of Poly (Trans-3-(3-Pyridyl)Acrylic Acid)/Multi-Walled Carbon Nanotubes Membrane for Electrochemically Simultaneously Detecting Catechol and Hydroquinone

Herein, conductive polymer membrane with excellent performance was successfully fabricated by integrating carboxylated multi-walled carbon nanotubes (MWCNTs) and poly (trans-3-(3-pyridyl) acrylic acid) (PPAA) film. The drop-casting method was employed to coated MWCNTs on the glassy carbon electrode (GCE) surface, and PPAA was then electropolymerized onto the surface of the MWCNTs/GCE in order to form PPAA-MWCNTs membrane. This enables the verification of the excellent performances of proposed membrane by electrochemically determining catechol (CC) and hydroquinone (HQ) as the model. Cyclic voltammetry experiments showed that the proposed membrane exhibited an obvious electrocatalytic effect on CC and HQ, owing to the synergistic effect of PPAA and MWCNTs. Differential pulse voltammetry was adopted for simultaneous detection purposes, and an increased electrochemical responded to CC and HQ. A concentration increase was found in the range of 1.0 × 10^-6 mol/L~1.0 × 10^-4 mol/L, and it exhibited a good linear relationship with satisfactory detection limits of 3.17 × 10^-7 mol/L for CC and 2.03 × 10^-7 mol/L for HQ (S/N = 3). Additionally, this constructed membrane showed good reproducibility and stability. The final electrode was successfully applied to analyze CC and HQ in actual water samples, and it obtained robust recovery for CC with 95.2% and 98.5%, and for HQ with 97.0% and 97.3%. Overall, the constructed membrane can potentially be a good candidate for constructing electrochemical sensors in environmental analysis.

Graphene Interlocking Carbon Nanotubes for High-Strength and High-Conductivity Fibers

Carbon nanotubes (CNTs) are promising building blocks for the fabrication of novel fibers with structural and functional properties. However, the mechanical and electrical performances of carbon nanotube fibers (CNTFs) are far lower than the intrinsic properties of individual CNTs. Exploring methods for the controllable assembly and continuous preparation of high-performance CNTFs is still challenging. Herein, a graphene/chlorosulfonic acid-assisted wet-stretching method is developed to produce highly densified and well-aligned graphene/carbon nanotube fibers (G/CNTFs) with excellent mechanical and electrical performances. Graphene with small size and high quality can bridge the adjacent CNTs to avoid the interfacial slippage under deformation, which facilitates the formation of a robust architecture with abundant conductive pathways. Their ordered structure and enhanced interfacial interactions endow the fibers with both high strength (4.7 GPa) and high electrical conductivity (more than 2 × 10⁶ S/m). G/CNTF-based lightweight wires show good flexibility and knittability, and the high-performance fiber heaters exhibit ultrafast electrothermal response over 1000 °C/s and a low operation voltage of 3 V. This method paves the way for optimizing the microstructures and producing high-strength and high-conductivity CNTFs, which are promising candidates for the high-value fiber-based applications.

Enriching WPCs and NFPCs with Carbon Nanotubes and Graphene

Carbon nanotubes (CNTs) and graphene, with their unique mechanical, electrical, thermal, optical, and wettability properties, are very effective fillers for many types of composites. Recently, a number of studies have shown that CNTs and graphene may be integrated into wood–plastic composites (WPCs) and natural-fibre-reinforced polymer composites (NFPCs) to improve the existing performance of the WPCs/NFPCs as well as enabling their use in completely new areas of engineering. The following review analyses the results of the studies presented to date, from which it can be seen that that inclusion of CNTs/graphene may indeed improve the mechanical properties of the WPCs/NFPCs, while increasing their thermal conductivity, making them electroconductive, more photostable, less sensitive to water absorption, less flammable, and more thermally stable. This study indicates that the composition and methods of manufacturing of hybrid WPCs/NFPCs vary significantly between the samples, with a consequent impact on the level of improvement of specific properties. This review also shows that the incorporation of CNTs/graphene may enable new applications of WPCs/NFPCs, such as solar thermal energy storage devices, electromagnetic shielding, antistatic packaging, sensors, and heaters. Finally, this paper recognises key challenges in the study area, and proposes future work.

Innovative Biochar-Based Composite Fibres from Recycled Material

Carbon materials are becoming crucial in several industrial sectors. The drawbacks of these materials include their high cost and oil-based essence. In recent years, recycled materials have become possible alternative sources of carbon with several advantages. Firstly, the production of this alternative source of carbon may help to reduce biomass disposal, and secondly, it contributes to CO₂ sequestration. The use of carbon derived from recycled materials by a pyrolysis treatment is called biochar. Here, we present composite materials based on different biochar filler contents dispersed in several thermoplastic polymer matrixes. Electrical conductivity and tensile break strength were investigated together with the material characterisation by DTA/TGA, XRD, and scanning electron microscopy (SEM) imaging. Materials with good flexibility and electrical conductivity were obtained. The local ordering in composites resembles both biochar and polymer ordering. The similarity between biochar and carbon nanotubes’ (CNTs) XRD patterns may be observed. As biochar is highly cost-effective, the proposed composites could become a valid substitute for CNT composites in various applications.

Hybrid Films Based on Bilayer Graphene and Single-Walled Carbon Nanotubes: Simulation of Atomic Structure and Study of Electrically Conductive Properties

One of the urgent problems of materials science is the search for the optimal combination of graphene modifications and carbon nanotubes (CNTs) for the formation of layered hybrid material with specified physical properties. High electrical conductivity and stability are one of the main optimality criteria for a graphene/CNT hybrid structure. This paper presents results of a theoretical and computational study of the peculiarities of the atomic structure and the regularities of current flow in hybrid films based on single-walled carbon nanotubes (SWCNTs) with a diameter of 1.2 nm and bilayer zigzag graphene nanoribbons, where the layers are shifted relative to the other. It is found that the maximum stresses on atoms of hybrid film do not exceed ~0.46 GPa for all considered topological models. It is shown that the electrical conductivity anisotropy takes place in graphene/SWCNT hybrid films at a graphene nanoribbon width of 4 hexagons. In the direction along the extended edge of the graphene nanoribbon, the electrical resistance of graphene/SWCNT hybrid film reaches ~125 kOhm; in the direction along the nanotube axis, the electrical resistance is about 16 kOhm. The prospects for the use of graphene/SWCNT hybrid films in electronics are predicted based on the obtained results.

Enhancing thermoelectric properties of single-walled carbon nanotubes using halide compounds at room temperature and above

Carbon nanotubes (CNTs) are materials with exceptional electrical, thermal, mechanical, and optical properties. Ever since it was demonstrated that they also possess interesting thermoelectric properties, they have been considered a promising solution for thermal energy harvesting. In this study, we present a simple method to enhance their performance. For this purpose, thin films obtained from high-quality single-walled CNTs (SWCNTs) were doped with a spectrum of inorganic and organic halide compounds. We studied how incorporating various halide species affects the electrical conductivity, the Seebeck coefficient, and the Power Factor. Since thermoelectric devices operate under non-ambient conditions, we also evaluated these materials' performance at elevated temperatures. Our research shows that appropriate dopant selection can result in almost fivefold improvement to the Power Factor compared to the pristine material. We also demonstrate that the chemical potential of the starting CNT network determines its properties, which is important for deciphering the true impact of chemical and physical functionalization of such ensembles.

Carbon Nanotube Films for Energy Applications

This perspective article describes the application opportunities of carbon nanotube (CNT) films for the energy sector. Up to date progress in this regard is illustrated with representative examples of a wide range of energy management and transformation studies employing CNT ensembles. Firstly, this paper features an overview of how such macroscopic networks from nanocarbon can be produced. Then, the capabilities for their application in specific energy-related scenarios are described. Among the highlighted cases are conductive coatings, charge storage devices, thermal interface materials, and actuators. The selected examples demonstrate how electrical, thermal, radiant, and mechanical energy can be converted from one form to another using such formulations based on CNTs. The article is concluded with a future outlook, which anticipates the next steps which the research community will take to bring these concepts closer to implementation.

Electronic structure of polypyrrole composited with a low percentage of graphene nanofiller

The low concentration of graphene (<5%) in graphene/polypyrrole composites makes it quite challenging to devise a theoretical model for these composites. Thus, herein, we present theoretical calculations to determine the geometric electronic and optical properties of graphene/polypyrrole composites. Ribbon and sheet models of various sizes were considered for graphene. Oligopyrrole of various lengths was deposited in the graphene model in different orientations including π-stacking, tilted and vertical orientations. Theoretical calculations at the M062X/def2-SVP level revealed that π-stacking is the preferred orientation. To model a lower concentration of graphene, sandwich complexes of oligopyrrole were considered with graphene nanoribbons. Interaction energies revealed that sandwich complexes possessed superior additivity. The NCI analysis established that weak van der Waals interactions existed in all composites. Moreover, the HOMO-LUMO gap decreases as the concentration of graphene increases. Thus, the computed optical band gap of the C₅₈H₂₄-based composite is about 1.7 eV, which is consistent with the reported experimental value (2.1-1.81 eV). The computed band gap further decreases to ∼1.6 eV when the proportion of graphene increases to C₆₄H₂₆. Thus, our results for the graphene nanoribbon-based polypyrrole composites are in good agreement with experimental results. The UV/visible spectra revealed that as the concentration of graphene increases, a red shift is observed for all the configurations, which is consistent with experimental results.

Theoretical Calculation of Hydrogen Generation and Delivery via Photocatalytic Water Splitting in Boron-Carbon-Nitride Nanotube/Metal Cluster Hybrid

Solar-driven water splitting is an appealing strategy to produce hydrogen energy. However, the non-negligible chance of reverse reactions due to a mixture of hydrogen molecules (H₂) with oxygen species poses challenges for safe H₂ collection and delivery, which hinders its applications. Using first-principles simulations, we propose a hybrid structure design where metal clusters of TM₄ (TM = Au/Pt) are encapsulated in boron-carbon-nitride nanotube (BCNNT) decorated with CuN₃ group. It can readily absorb ultraviolet-visible solar light to generate charge carriers. The energetic electrons and holes would be separately delivered to the reduction site of TM₄ and the oxidation site of the BCNNT layer. Then, protons generated by water dissociation at the BCNNT layer will penetrate through BCNNT and consequently meet electrons at the TM₄ site to be reduced into H₂. As a selective sieve, BCNNT prevents oxygen species from going inside and H₂ from crossing out so that H₂ can be completely isolated. Further, the sufficient space of the tubular cavity endows the transportation feasibility of the produced H₂ along the nanotube for collection. This proposed design combines photocatalytic hydrogen production and safe delivery, which may help in developing a practical solution for a photodriven hydrogen production.

Recent Advances of Graphene-Derived Nanocomposites in Water-Based Drilling Fluids

Nanocomposite materials have distinctive potential for various types of captivating usage in drilling fluids as a well-designed solution for the petroleum industry. Owing to the improvement of drilling fluids, it is of great importance to fabricate unique nanocomposites and advance their functionalities for amplification in base fluids. There is a rising interest in assembling nanocomposites for the progress of rheological and filtration properties. A series of drilling fluid formulations have been reported for graphene-derived nanocomposites as additives. Over the years, the emergence of these graphene-derived nanocomposites has been employed as a paradigm to formulate water-based drilling fluids (WBDF). Herein, we provide an overview of nanocomposites evolution as engineered materials for enhanced rheological attributes in drilling operations. We also demonstrate the state-of-the-art potential graphene-derived nanocomposites for enriched rheology and other significant properties in WBDF. This review could conceivably deliver the inspiration and pathways to produce novel fabrication of nanocomposites and the production of other graphenaceous materials grafted nanocomposites for the variety of drilling fluids.

Spun Carbon Nanotube Fibres and Films as an Alternative to Printed Electronic Components

Current studies of carbon nanotubes have enabled both new electronic applications and improvements to the performance of existing ones. Manufacturing of macroscopic electronic components with this material generally involves the use of printed electronic methods, which must use carbon nanotube (CNT) powders. However, in recent years, it has been shown that the use of ready-made self-standing macroscopic CNT assemblies could have considerable potential in the future development of electronic components. Two examples of these are spun carbon nanotube fibers and CNT films. The following paper considers whether these spun materials may replace printed electronic CNT elements in all applications. To enable the investigation of this question some practical experiments were undertaken. They included the formation of smart textile elements, flexible and transparent components, and structural electronic devices. By taking this approach it has been possible to show that CNT fibres and films are highly versatile materials that may improve the electrical and mechanical performance of many currently produced printed electronic elements. Additionally, the use of these spun materials may enable many new applications and functionalities particularly in the area of e-textiles. However, as with every new technology, it has its limitations, and these are also considered.

Stretchable and Washable Electroluminescent Display Screen-Printed on Textile

Stretchable polymer composites are a new group of materials with a wide range of application possibilities in wearable electronics. The purpose of this study was to fabricate stretchable electroluminescent (EL) structures using developed polymer compositions, based on multiple different nanomaterials: luminophore nanopowders, dielectric, carbon nanotubes, and conductive platelets. The multi-layered EL structures have been printed directly on textiles using screen printing technology. During research, the appropriate rheological properties of the developed composite pastes, and their suitability for printed electronics, have been confirmed. The structure that has been created from the developed materials has been tested in terms of its mechanical strength and resistance to washing or ironing.