Highly Thermal Conductivities, Excellent Mechanical Robustness and Flexibility, and Outstanding Thermal Stabilities of Aramid Nanofiber Composite Papers with Nacre-Mimetic Layered Structures

0D/2D Co-Doping Network Enhancing Thermal Conductivity of Radiative Cooling Film for Electronic Device Thermal Management

The radiative cooling has great potential for electronic device cooling without requiring any energy consumption. However, a low thermal conductivity of most radiative cooling materials limits their application. Herein, a multishape codoping strategy was proposed to achieve collaborative enhancement of thermal conductivity and radiative properties. The hBN-coated hollow SiO2 particles were prepared based on electrostatic self-assembly technology, which were then mixed with hBN platelets and doped into a poly(vinylidene fluoride-co-hexafluoropropylene) substrate. Discrete dipole approximation theory was employed to reveal the mechanism and optimize the particle size. The results showed that the multishape codoping method can significantly improve the radiative performance, with 94.9% reflectivity and 91.2% emissivity. In addition, this zero-dimensional and two-dimensional composite doping structure facilitated the formation of a thermal conduction network, which enhanced the thermal conductivity of the film up to 1.32 W m-1 K-1. The high thermal conductivity radiative cooling film can decrease the heater temperature from 58.8 to 31.3 °C, with a further reduction of temperature by 7.2 °C compared to the radiative cooling substrates with low thermal conductivity. The net cooling power of the film can reach 102.5 W m-2 under direct sunlight. This work provides a novel strategy for high-efficiency electronic device cooling.

Highly Thermally Conductive Super-Aligned Boron Nitride Nanotube Films for Flexible Electronics Thermal Management

Flexible electronics toward high integration, miniaturization, and multifunctionality, leading to a dramatic increase in power density. However, the low thermal conductivity of flexible substrates impedes efficient heat dissipation and device performance improvement. In this work, we propose a template-assisted chemical conversion strategy for obtaining boron nitride nanotube (BNNT) films with high thermal conductivity and great flexibility. Aligned carbon nanotube (CNT) films have been adopted as templates; a low-temperature chemical conversion followed by a high-temperature annealing has been carried out to produce a highly ordered BNNT film. Benefiting from the high orientation order, the BNNT film exhibits an exceptional thermal conductivity of 45.5 W m-1 K-1 and presents excellent heat dissipation capability, much superior to the commonly used polyimide film. Furthermore, the BNNT film demonstrated excellent flexibility and high insulation resistance. The test of integration with film resistors demonstrated its potential as a thermally conductive substrate for electronics cooling. This work provides a solution for the effective thermal management of flexible electronics.

Higher-Order Structural Analysis of a Transparent and Flexible High Thermal Conductive Liquid Crystalline Elastomer Sheet and Its Composite

Transparency, flexibility, and high thermal conductivity are trade-offs. Specifically, we have investigated a cross-linked acrylic liquid crystal elastomer (LCE) that exhibits both transparency and flexibility while maintaining a high level of thermal conductivity. The transparent monodomain LCE sheet was achieved through a process of stretching an initially opaque polydomain sheet to 80% elongation and subsequently subjecting it to photocuring. The thermal conductivity in the stretching direction (x) of the monodomain LCE sheet was found to be 1.8 times higher than that of the prestretched polydomain sheet, consistent with findings from previous studies. However, in the orthogonal direction (y) to the stretching (x) direction, the thermal conductivity exhibited an even higher value, being 1.7 times greater than in the x-direction, with a value of 3.0 W/(m·K). This unique observation prompted us to conduct further investigation through higher-order structural analysis of these LCE sheets using 2D wide-angle X-ray scattering (WAXS) analysis. In the transparent sheet, the LCE molecules were aligned in the sheet in the stretching x-direction (monodomain structure) for the out-of-plane direction. However, in the in-plane x-direction, the molecular plane spacing exhibited random orientation at a period of 0.45 nm. In contrast, within the y-direction of the inner layer, the molecular plane spacing exhibited a uniaxial horizontal orientation at the same period length as in the x-direction. The heat energy entering into the y-direction once spreads to the x-direction, but it was considered that the reason for the higher thermal conductivity to the y-direction would be forming covalent bonds that function as new heat transmission paths, in the direction intersecting to the x-direction during photocuring. Therefore, we concluded that the synergistic effect of the high level of the ordered inner structure and covalent bonding structure due to cross-linking in the y-direction contributes to its higher thermal conductivity compared to that in the x-direction, which exhibits a random in-plane structure. Additionally, we have fabricated an LCE composite sheet filled with 75 vol % of alumina particles using a polydomain-type LCE as the base material. The composite sheet exhibits remarkable thermal conductivity in the thickness direction, measuring at 9.8 W/(m·K), while maintaining a flexibility characterized by an elastic modulus of 70 MPa. This thermal conductivity surpasses that of a nonmesogenic acrylic composite sheet with identical alumina particle filling, which measured at 3.9 W/(m·K), more than twice as much. The presence of the mesogen skeleton has been demonstrated to enhance heat transfer, even within soft composites, by facilitating the formation of an ordered structure.

Guidelines derived from biomineralized tissues for design and construction of high-performance biomimetic materials: from weak to strong

Living organisms in nature have undergone continuous evolution over billions of years, resulting in the formation of high-performance fracture-resistant biomineralized tissues such as bones and teeth to fulfill mechanical and biological functions, despite the fact that most inorganic biominerals that constitute biomineralized tissues are weak and brittle. During the long-period evolution process, nature has evolved a number of highly effective and smart strategies to design chemical compositions and structures of biomineralized tissues to enable superior properties and to adapt to surrounding environments. Most biomineralized tissues have hierarchically ordered structures consisting of very small building blocks on the nanometer scale (nanoparticles, nanofibers or nanoflakes) to reduce the inherent weaknesses and brittleness of corresponding inorganic biominerals, to prevent crack initiation and propagation, and to allow high defect tolerance. The bioinspired principles derived from biomineralized tissues are indispensable for designing and constructing high-performance biomimetic materials. In recent years, a large number of high-performance biomimetic materials have been prepared based on these bioinspired principles with a large volume of literature covering this topic. Therefore, a timely and comprehensive review on this hot topic is highly important and contributes to the future development of this rapidly evolving research field. This review article aims to be comprehensive, authoritative, and critical with wide general interest to the science community, summarizing recent advances in revealing the formation processes, composition, and structures of biomineralized tissues, providing in-depth insights into guidelines derived from biomineralized tissues for the design and construction of high-performance biomimetic materials, and discussing recent progress, current research trends, key problems, future main research directions and challenges, and future perspectives in this exciting and rapidly evolving research field.

Aramid nanofiber membrane decorated with monodispersed silver nanoparticles as robust and flexible SERS chips for trace detection of multiple toxic substances

Aramid nanofibers (ANFs) as an innovative nanoscale building block exhibit great potential for novel high-performance multifunctional membranes attributed to their extraordinary performance. However, the application of aramid nanofibers in the field of surface enhanced Raman scattering (SERS) sensing has been rarely reported. In this work, aramid nanofibers derived from commercial Kevlar fibers were synthesized by a facile dimethyl sulfoxide/potassium hydroxide (DMSO/KOH) solution treatment. The monodispersed silver nanoparticle-decorated aramid nanofiber (m-Ag@ANF) membranes were constructed by an efficient vacuum filtration technique. Taking advantages of unique intrinsic properties of ANF, the m-Ag@ANF substrates exhibit good flexibility, excellent mechanical properties and prominent thermal stability. Besides, due to the abundance of positively charged amino-group on the ANF substrates, the negatively charged m-AgNPs were uniformly and firmly deposited on the surface of ANF substrate through electrostatic interactions. As a result, the optimal flexible m-Ag-9@ANF SERS substrate exhibits high sensitivity of 10-9 M for methylene blue (MB) and excellent signal reproducibility (RSD = 6.37 %), as well as outstanding signal stability (up to 15 days). Besides, the 2D Raman mapping and FDTD simulations further reveal prominent signal homogeneity and strong electric field distribution for flexible m-Ag-9@ANF SERS substrate. Finally, it is demonstrated that the flexible m-Ag-9@ANF SERS substrate can also be used for detection of toxic molecules on irregular surfaces by a feasible paste-and-read process. The m-Ag@ANF paper exhibits potential applications as a flexible, low-cost, robust and stable SERS sensing platform for trace detection of toxic materials.

Self-Adaptive Rapid Thermal Conductive Fabrics Based on Hygroscopic Shrinkage Response for Personal Cooling and Drying

Advanced fabrics with thermal wet management capability as low energy consumption media contribute to personal cooling and drying. Nevertheless, it remains a great challenge to obtain intelligent fabrics with adjustable thermal conductivity (TC) capable of bridging the supply and demand between human body temperature and self-adaptive thermal conduction. Herein, we report hygroscopic-shrinkage nanofiber-based fabrics with excellent moisture sensitivity and significant volume shrinkage, which benefits the construction of high-density thermal conductive pathways by absorbing sweat, with a maximum sweat absorption rate reaching up to 1781%. The TC of the shrunken fabric is significantly increased from the initial 0.102 to 0.731 W·m-1 K-1 with a volume shrinkage rate of 89% due to the synergistic effect of van der Waals force, capillary force, viscous resistance, and gravity. Besides, an enhanced TC of the resulting fabrics facilitates rapid heat transfer to the environments. By capturing the surface temperature variations of the fabric after shrinkage and commercially available cotton/Coolmax, we obtained the fabric that releases the same amount of heat in a shorter period of time (3.3 s). With its exceptional personal thermal and wet management properties, this study paves the way for designing new-generation intelligent fabrics capable of creating more comfortable microclimates.

Thermal Conductivity Enhancement of Polymeric Composites Using Hexagonal Boron Nitride: Design Strategies and Challenges

With the integration and miniaturization of chips, there is an increasing demand for improved heat dissipation. However, the low thermal conductivity (TC) of polymers, which are commonly used in chip packaging, has seriously limited the development of chips. To address this limitation, researchers have recently shown considerable interest in incorporating high-TC fillers into polymers to fabricate thermally conductive composites. Hexagonal boron nitride (h-BN) has emerged as a promising filler candidate due to its high-TC and excellent electrical insulation. This review comprehensively outlines the design strategies for using h-BN as a high-TC filler and covers intrinsic TC and morphology effects, functionalization methods, and the construction of three-dimensional (3D) thermal conduction networks. Additionally, it introduces some experimental TC measurement techniques of composites and theoretical computational simulations for composite design. Finally, the review summarizes some effective strategies and possible challenges for the design of h-BN fillers. This review provides researchers in the field of thermally conductive polymeric composites with a comprehensive understanding of thermal conduction and constructive guidance on h-BN design.

High-Performance, Multifunctional, and Designable Carbon Fiber Felt Skeleton Epoxy Resin Composites EP/CF-(CNT/AgBNs)x for Thermal Conductivity and Electromagnetic Interference Shielding

In this work, high-performance epoxy resin (EP) composites with simultaneous excellent thermal conductivity (TC) and outstanding electromagnetic shielding properties are fabricated through the structural synergy of 1D carbon nanotubes and 2D silver-modified boron nitride nanoplates (CNT/AgBNs) to erect microscopic 3D networks on long-range carbon fiber (CF) felt skeletons. The line-plane combination of CNT/AgBNs improve the interfacical bonding involving EP and CF felts and alleviate the phonon scattering at the interface. Eventually, the TC of the EP composites is enhanced by 333% (up to 0.91 W m-1 K-1 ) with respect to EP due to the efficient and orderly transmission of phonons along the 3D pathway. Meanwhile, the unique anisotropic structure of CF felt and exceptional insulating BNs diminishes the electronic conduction between CNT and CFs, which protects the through-plane insulating properties of EP composites. Furthermore, the EP composites present favorable electromagnetic shielding properties (51.36 dB) attributed to the multiple reflection and adsorption promoted by the multiple interfaces of stacked AgBNs and heterointerface among CNT/AgBNs, CF felt and EP. Given these distinguishing features, the high-performance EP composites open a convenient avenue for electromagnetic wave (EMW) shielding and thermal management applications.

On-Demand Preparation of Boron Nitride Nanosheets for Functional Nanocomposites

Boron nitride nanosheets (BNNSs) have garnered significant attention across diverse fields; however, accomplishing on-demand, large-scale, and highly efficient preparation of BNNSs remains a challenge. Here, an on-demand preparation (OdP) method combining high-pressure homogenization and short-time ultrasonication is presented; it enables a highly efficient and controllable preparation of BNNSs from bulk hexagonal boron nitride (h-BN). The homogenization pressure and number of cycles are adjusted, and the production efficiency and yield of BNNSs reach 0.95 g g-1 h-1 and 82.8%, respectively, which significantly exceed those attained by using existing methods. The universality of the OdP method is demonstrated on h-BN raw materials of various bulk sizes from various producers. Furthermore, this method allows the preparation of BNNSs having specific sizes based on the final requirements. Both simulation and experimental results indicate that large BNNSs are particularly suitable for enhancing the thermal conductivity and electrical insulation properties of dielectric polymer nanocomposites. Interestingly, the small BNNS-filled photonic nanocomposite films fabricated via the OdP method exhibit superior daytime radiative cooling properties. Additionally, the OdP method offers the benefits of low energy consumption and reduced greenhouse gas emissions and fossil energy use. These findings underscore the unique advantages of the OdP method over other techniques for a high-efficiency and controllable preparation of large BNNSs.

Development of biobased multifunctional films incorporated with essential oils@polydopamine nanocapsules for food preservation applications

A novel multifunctional soy protein isolate-carboxymethyl cellulose (SPI-CMC) based nanocomposite film was successfully prepared by introducing the polydopamine encapsulated essential oils (EOs@PDA) nanocapsules for food packaging. The EOs@PDA nanocapsules possessed smooth spherical morphology with good dispersion, and the particle size was about 283 nm. The influence of EOs@PDA nanocapsules on the physical, chemical and biological properties of EOs@PDA/SPI-CMC nanocomposite film was investigated. The EOs@PDA nanocapsules were crosslinked with SPI-CMC matrix and distributed uniformly in the matrix. The nanocomposite film with 1 wt% nanocapsules (EP/S-C) also showed excellent antioxidant activity (66.6 ± 0.3 % on DPPH and 98.6 ± 0.1 % on ABTS), superior UV-blocking properties (100 %), advanced antibacterial ability against E. coli and S. aureus, favorable biodegradability (>90 %) and relatively low In vitro cytotoxicity. Also, the EP/S-C nanocomposite film displayed potential to extend the shelf life of fresh cut apple slices (>24 h), perishable cherry tomatoes and blueberries (>6 days). The results suggested that the EOs@PDA/SPI-CMC nanocomposite film had a great possibility in the field of biodegradable and antimicrobial materials for food packaging.

Data-Driven Framework toward Accurate Prediction of Interfacial Thermal Resistance in Particulate-Filled Composites

The interfacial thermal resistance (ITR) inside the particulate-filled polymer composite is a bottleneck for improving the thermal conductivity (TC) of the material. Getting full knowledge of the ITR is crucial to the material design as well as to a faithful prediction of TC of the composite. However, a method fully taking into account the local circumstances inside the composite is yet to be developed to precisely characterize the ITR. Here, we propose a comprehensive framework combining high-throughput numerical simulations, machine learning and optimization algorithms, and experiments, which is demonstrated to be robust for the accurate determination of ITRs inside the particulate-filled composites. The strategy extracts as much information as possible about the structure and heat transfer characteristics of the composite based on simple experiments, which lays the foundation for the method to be effective. We show that the polymer-filler ITRs and the effective filler-filler contact ITRs predicted with the method faithfully represent the true characteristics inside the composite materials; they also provide the exact effective parameters, which cannot be obtained from experiments, for accurate numerical prediction of TCs of composite materials with high efficiency. As a result, the framework not only provides a robust tool for accurate characterization of ITRs inside composites but also paves the way for virtual high-throughput formula screening of thermally conductive composite materials that could be used in industrial product design.

Constructing Hierarchical Polymer Nanocomposites with Strongly Enhanced Thermal Conductivity

The rapid advancement of communication technology has substantially increased the demand for advanced electronic packaging materials with high thermal conductivity and outstanding electrical insulation properties. In this study, we design polyvinyl alcohol/polydopamine-modified boron nitride nanosheet (PVA/BNNS@PDA) nanocomposites with hierarchical structures by combining electrospinning, vacuum filtration deposition, and hot pressing. The modified BNNS@PDA improves the interaction between the filler and the polymer matrix while reducing the interfacial thermal resistance, resulting in superior thermal conductivity, excellent insulation, and perfect flexibility. The PVA/BNNS@PDA nanocomposites possess an ultrahigh in-plane thermal conductivity of 16.6 W/(m·K) at 35.54 wt % BNNS@PDA content. Even after 2000 folds, the nanocomposites do not undergo any crack, showing their ultrahigh thermal conductivity behavior. Furthermore, the nanocomposites exhibit a volume resistivity above 1014 Ω·cm, which is well above the standard for insulating materials. Based on these results, this work provides a novel method to produce nanocomposites with high thermal conductivity, offering a new perspective to design advanced thermal management materials.

Flexible and Ultrathin Graphene/Aramid Nanofiber Carbonizing Films with Nacre-like Structures for Heat-Conducting Electromagnetic Wave Shielding/Absorption

Electromagnetic interference (EMI) shielding and electromagnetic wave absorption (EWA) materials with good thermal management and flexibility properties are urgently needed to meet the more complex modern service environment, especially in the field of smart wearable electronics. How to balance the relation of electromagnetic performance, thermal management, flexibility, and thickness in material design is a crucial challenge. Herein, graphene nanosheets/aramid nanofiber (C-GNS/ANF) carbonizing films with nacre-like structures were fabricated via the blade-coating/carbonization procedure. The ingenious configuration from highly ordered alignment GNS interactively connected by a carbonized ANF network can effectively improve the thermal/electrical conductivity of a C-GNS/ANF film. Specifically, the ultrathin C-GNS/ANF film with a thickness of 17 μm shows excellent in-plane thermal conductivity (TC) of 79.26 W m^-1 K^-1 and superior EMI shielding up to 56.30 dB. Moreover, the obtained C-GNS/ANF film can be used as a lightweight microwave absorber, achieving excellent microwave absorption performance with a minimum reflection loss of -56.07 dB at a thickness of 1.5 mm and a maximum effective absorption bandwidth of 5.28 GHz at an addition of only 5 wt %. Furthermore, the C-GNS/ANF films demonstrate good flexibility, outstanding thermal stability, and flame retardant properties. Overall, this work indicates a prospective direction for the development of the next generation of electromagnetic wave absorption/shielding materials with high-performance heat conduction.

Dopamine-Mediated Graphene Bridging Hexagonal Boron Nitride for Large-Scale Composite Films with Enhanced Thermal Conductivity and Electrical Insulation

Heat accumulation generated from confined space poses a threat to the service reliability and lifetime of electronic devices. To quickly remove the excess heat from the hot spot, it is highly desirable to enhance the heat dissipation in a specific direction. Herein, we report a facile route to fabricate the large-scale composite film with enhanced thermal conductivity and electrical insulation. The well-stacked composite films were constructed by the assembly of polydopamine (PDA)-modified graphene nanosheets (GNS_PDA) and hexagonal boron nitride (BN_PDA), as well as bacterial cellulose (BC). The introduction of the PDA layer greatly improves the interface compatibility between hybrid fillers and BC matrix, and the presence of GNS_PDA-bridging significantly increases the probability of effective contact with BN_PDA fillers, which is beneficial to form a denser and complete "BN-GNS-BN" heat conduction pathway and tight filler-matrix network, as supported by the Foygel model fitting and numerical simulation. The resulting BC/BN_PDA/GNS_PDA film shows the thermal conductivity and tensile strength of 34.9 W·m^-1·K^-1 and 30.9 MPa, which separately increases to 161% and 155% relative to the BC/BN_PDA film. It was found that the low electrically conductive and high thermal conductive properties can be well balanced by tuning the mass ratio of GNS_PDA at 5 wt%, and the electrical conductivity caused by GNS_PDA can be effectively blocked by the BN_PDA filler network, giving the low electrical conductivity of 1.8 × 10^-10 S·cm^-1. Meanwhile, the BC/BN_PDA/GNS_PDA composite films effectively transfer the heat and diminish the hot-spot temperature in cooling LED chip module application. Thus, the present study may pave the way to promoting the industrialization of scalable thermal management devices.

Enhancing Bioinspired Aramid Nanofiber Networks by Interfacial Hydrogen Bonds for Multiprotection under an Extreme Environment

In nature, many insects have evolved sclerotic cuticles to shelter their soft bodies, which are considered as "body armor". For beetles, the epidermis is composed of cross-linked intertwined fiber structures; such a fiber network structure could provide an anti-impact function for composites. Aramid nanofibers (ANFs) are of great interest in various applications due to their 1D nanoscale, high aspect ratio, excellent strength and modulus, and impressive chemical and thermal stability. In this paper, a kind of ANF network is prepared by a layer-by-layer assembly method. The enhancing ANF networks are developed by introducing carboxylated chitosan acting as a hydrogen-bondin donors as well as a soft interlocking agent (C-ANFs). As a result of the formation of a nanostructure and the hydrogen-bond interactions, the assembled C-ANF networks presented a high tensile strength (551.4 MPa) and toughness (4.0 MJ/m²), which is 2.41 times and 32.69 times those of neat ANF networks, respectively. The excellent mechanical properties endow C-ANF networks with distinguished anti-impact performance. The specific dissipated energy after mass normalization reaches 7.34 MJ/kg, which is significantly superior to traditional protective materials such as steel and Kevlar composites. A nonlinear spring model is also used to explain the mechanical behavior of C-ANF networks. In addition to anti-impact protection, C-ANF networks can realize more than 99% of UV irradiation absorption and have excellent thermal stability. The chemical stability of C-ANF networks make them survive in acid and alkali environments. The above characteristics show that C-ANF networks have great application value in multiscale protection scenarios under an extreme environment.

Synthesis and Properties of a Novel Thermally Conductive Pressure-Sensitive Adhesive with UV-Responsive Peelability

Thermally conductive pressure-sensitive adhesive (PSA) has received a great amount of attention in recent years, but the traditional PSA hardly loses adhesion properties after UV irradiation or heating. Therefore, endowing thermally conductive adhesive with UV-responsive peelability becomes a design strategy. Herein, vinyl-functionalized graphene (AA-GMA-G) is prepared by modifying graphene with acrylic acid and subsequently reacting with glycidyl methacrylate. Then, the UV-curable acrylate copolymer is synthesized by grafting glycidyl methacrylate. Finally, the novel thermally conductivity PSA with UV-responsive peelability is obtained by blending the copolymer with AA-GMA-G and photoinitiator. The results show that the PSA at 2 wt% AA-GMA-G loading exhibits an excellent thermal conductivity (0.74 W m^-1 K^-1 ) and a relatively strong peel strength, increasing by 15% compared with pristine graphene/PSA. Interestingly, the peel strength of AA-GMA-G/PSA can achieve a dramatic drop after UV treatment, and the decrease rate is 96.7%. Therefore, the novel thermally conductive PSA with UV-responsive peelability has potential applications in certain electronic devices.

Multifunctional Thermally Conductive Composite Films Based on Fungal Tree-like Heterostructured Silver Nanowires@Boron Nitride Nanosheets and Aramid Nanofibers

Thermal conduction for electronic equipment has grown in importance in light of the burgeoning of 5G communication. It is imperatively desired to design highly thermally conductive fillers and polymer composite films with prominent Joule heating characteristics and extensive mechanical properties. In this work, "solvothermal & in situ growth" method is carried out to prepare "Fungal tree"-like hetero-structured silver nanowires@boron nitride nanosheet (AgNWs@BNNS) thermally conductive fillers. The thermally conductive AgNWs@BNNS/ANF composite films are obtained by the method of "suction filtration self-assembly and hot-pressing". When the mass fraction of AgNWs@BNNS is 50 wt%, AgNWs@BNNS/ANF composite film presents the optimal thermal conductivity coefficient of 9.44 W/(m ⋅ K) and excellent tensile strength of 136.6 MPa, good temperature-voltage response characteristics, superior electrical stability and reliability, which promise a wide application potential in 5G electronic devices.

Contributing Factors of Dielectric Properties for Polymer Matrix Composites

Due to the trend of multi-function, integration, and miniaturization of electronics, traditional dielectric materials are difficult to satisfy new requirements, such as balanced dielectric properties and good designability. Therefore, high dielectric polymer composites have attracted wide attention due to their outstanding processibility, good designability, and dielectric properties. A number of polymer composites are employed in capacitors and sensors. All these applications are directly affected by the composite's dielectric properties, which are highly depended on the compositions and internal structure design, including the polymer matrix, fillers, structural design, etc. In this review, the influences of matrix, fillers, and filler arrangement on dielectric properties are systematically and comprehensively summarized and the regulation strategies of dielectric loss are introduced as well. Finally, the challenges and prospects of high dielectric polymer composites are proposed.

Silver nanoparticles decorated meta-aramid nanofibrous membrane with advantageous properties for high-performance flexible pressure sensor

Flexible pressure sensors have received tremendous attention for various wearable applications. However, it remains a critical challenge to develop a flexible pressure sensor with excellent sensitivity performances and multiple advantageous properties. Herein, a high-performance flexible piezoresistive pressure sensor PMIA@PDA@Ag was developed, which sensitive component is consisted of Ag nanoparticles decorated polydopamine (PDA)-modified meta-aramid (poly(m-phenylene isophthalamide), PMIA) nanofibrous membrane. The PMIA@PDA@Ag pressure sensor shows excellent mechanical, thermal insulation, antibacterial and breathable properties, as well as remarkable sensing performances including high sensitivity, wide detectable pressure range, rapid response speed and good cyclic durability. In addition, it also shows great sensing performances in monitoring various human behaviors in real-time, including large-scale motions and subtle physiological signals.

Bio-Inspired Aramid Fibers@silica Binary Synergistic Aerogels with High Thermal Insulation and Fire-Retardant Performance

Flame-retardant, thermal insulation, mechanically robust, and comprehensive protection against extreme environmental threats aerogels are highly desirable for protective equipment. Herein, inspired by the core (organic)-shell (inorganic) structure of lobster antenna, fire-retardant and mechanically robust aramid fibers@silica nanocomposite aerogels with core-shell structures are fabricated via the sol-gel-film transformation and chemical vapor deposition process. The thickness of silica coating can be well-defined and controlled by the CVD time. Aramid fibers@silica nanocomposite aerogels show high heat resistance (530 °C), low thermal conductivity of 0.030 W·m^-1·K^-1, high tensile strength of 7.5 MPa and good flexibility. More importantly, aramid fibers@silica aerogels have high flame retardancy with limiting oxygen index 36.5. In addition, this material fabricated by the simple preparation process is believed to have potential application value in the field of aerospace or high-temperature thermal protection.

Amino Acid-Assisted Sand-Milling Exfoliation of Boron Nitride Nanosheets for High Thermally Conductive Thermoplastic Polyurethane Composites

Boron nitride nanosheets (BNNSs) show excellent thermal, electrical, optical, and mechanical properties. They are often used as fillers in polymers to prepare thermally conductive composites, which are used in the production of materials for thermal management, such as electronic packaging. Aside from the van der Waals force, there are some ionic bond forces between hexagonal boron nitride (h-BN) layers that result in high energy consumption and make BNNSs easily agglomerate. To overcome this issue, L-lysine (Lys) was first employed as a stripping assistant for preparing graft-functionalized BNNSs via mechanical sand-milling technology, and the obtained Lys@BNNSs can be added into thermoplastic polyurethane (TPU) by solution mixing and hot-pressing methods to prepare thermally conductive composites. This green and scalable method of amino acid-assisted sand-milling can not only exfoliate the bulk h-BN successfully into few-layer BNNSs but also graft Lys onto the surface or edges of BNNSs through Lewis acid–base interaction. Furthermore, benefiting from Lys’s highly reactive groups and biocompatibility, the compatibility between functionalized BNNSs and the TPU matrix is significantly enhanced, and the thermal conductivity and mechanical properties of the composite are remarkably increased. When the load of Lys@BNNSs is 3 wt%, the thermal conductivity and tensile strength of the obtained composites are 90% and 16% higher than those of the pure TPU, respectively. With better thermal and mechanical properties, Lys@BNNS/TPU composites can be used as a kind of heat dissipation material and have potential applications in the field of thermal management materials.

Thermally Conductive but Electrically Insulating Polybenzazole Nanofiber/Boron Nitride Nanosheets Nanocomposite Paper for Heat Dissipation of 5G Base Stations and Transformers

The rapid development of 5G equipment and high-power density electronic devices calls for high thermal conductivity materials for heat dissipation. Dielectric polymer composites are highly promising as the electrical insulation, mechanical property, thermal stability, and even fire retardance are also of great importance for electrical and electronic applications. However, the current thermal conductivity enhancement of dielectric polymer composites is usually at the cost of lowering the mechanical and electrical insulating properties. In this work, we report the facile preparation of highly thermally conductive and electrically insulating poly(p-phenylene benzobisoxazole) nanofiber (PBONF) composites by incorporating a low weight fraction of functionalized boron nitride nanosheets (BNNSs). With strong electrostatic interaction, the BNNSs are encapsulated by PBONFs, and the constructed robust interconnected network makes the nanocomposites exhibit a nacre-like structure. Accordingly, the nanocomposite paper has a high in-plane thermal conductivity of 21.34 W m^-1 K^-1 at a low loading of 10 wt % BNNSs and exhibits an ultrahigh strength of 206 MPa. Additionally, the nanocomposite paper exhibits superior electrical insulation properties up to higher than 350 °C and excellent fire retardance. The strong heat dissipation capability of the nanocomposite paper was demonstrated in 5G base stations and control transformers, showing wide potential applications in high power density electrical equipment and electronic devices.

Mitochondria-targeting Polydopamine-coated Nanodrugs for Effective Photothermal- and Chemo- Synergistic therapies Against Lung Cancer

Targeting mitochondria via nano platform emerged as an attractive anti-tumor pathway due to the central regulation role in cellar apoptosis and drug resistance. Here, a mitochondria-targeting nanoparticle (TOS-PDA-PEG-TPP) was designed to precisely deliver polydopamine (PDA) as the photothermal agent and alpha-tocopherol succinate (α-TOS) as the chemotherapeutic drug to the mitochondria of the tumor cells, which inhibits the tumor growth through chemo- and photothermal- synergistic therapies. TOS-PDA-PEG-TPP was constructed by coating PDA on the surface of TOS NPs self-assembled by α-TOS, followed by grafting PEG and triphenylphosphonium (TPP) on their surface to prolong the blood circulation time and target delivery of TOS and PDA to the mitochondria of tumor cells. In vitro studies showed that TOS-PDA-PEG-TPP could be efficiently internalized by tumor cells and accumulated at mitochondria, resulting in cellular apoptosis and synergistic inhibition of tumor cell proliferation. In vivo studies demonstrated that TOS-PDA-PEG-TPP could be efficiently localized at tumor sites and significantly restrain the tumor growth under NIR irradiation without apparent toxicity or deleterious effects. Conclusively, the combination strategy adopted for functional nanodrugs construction aimed at target-delivering therapeutic agents with different action mechanisms to the same intracellular organelles can be extended to other nanodrugs-dependent therapeutic systems.

Flexible, Strong and Multifunctional Anf@Ag Nanocomposite Film for Human Physiology and Motion Monitoring

To expand the application range of flexible pressure sensors, endowing them with multifunction capabilities becomes extremely important. Herein, a flexible, strong and multifunctional nanocomposite film was prepared by introducing silver nanoparticles (Ag NPs) into aramid nanofiber (ANF) film using a simple two-step vacuum filtration method. When the Ag content was 27.6 vol%, the electrical resistance of the resulting ANF@Ag nanocomposite film was as low as 1.63 Ω/cm2, and the water contact angle of the nanocomposite film reached 153.9 ± 1°. Compared to the ANF film, the tensile strength of the nanocomposite film increased from 55 MPa to 66.3 MPa with an increase of 20.5%. After being applied to the human body, the nanocomposite film served as a pressure sensor that was able to recognize different stimuli for healthcare monitoring. Based on the advantages, it may become a potential candidate for electronic skin, intelligent wearable devices and medical detection equipment.

Flexible Ti3C2T x /(Aramid Nanofiber/PVA) Composite Films for Superior Electromagnetic Interference Shielding

Multifunctional electromagnetic interference (EMI) shielding materials would solve electromagnetic radiation and pollution problems from electronic devices. Herein, the directional freeze-drying technology is utilized to prepare the aramid nanofiber/polyvinyl alcohol aerogel with a directionally porous structure (D-ANF/PVA), and the Ti₃C₂T_x dispersion is fully immersed into the D-ANF/PVA aerogel via ultrasonication and vacuum-assisted impregnation. Ti₃C₂T_x/(ANF/PVA) EMI shielding composite films with directionally ordered structure (D-Ti₃C₂T_x/(ANF/PVA)) are then prepared by freeze-drying and hot pressing. Constructing a directionally porous structure enables the highly conductive Ti₃C₂T_x nanosheets to be wrapped on the directionally porous D-ANF/PVA framework in order arrangement and overlapped with each other. And the hot pressing process effectively reduces the layer spacing between the stacked wavy D-ANF/PVA, to form a large number of Ti₃C₂T_x-Ti₃C₂T_x continuous conductive paths, which significantly improves the conductivity of the D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film. When the amount of Ti₃C₂T_x is 80 wt%, the EMI shielding effectiveness (EMI SE) and specific SE (SSE/t) of D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film achieve 70 dB and 13790 dB·cm²·g⁻¹ (thickness and density of 120 μm and 0.423 g·cm⁻³), far superior to random-structured Ti₃C₂T_x/(ANF/PVA) (R-Ti₃C₂T_x/(ANF/PVA)) composite film (46 dB and 9062 dB·cm²·g⁻¹, respectively) via blending-freeze-drying followed by hot pressing technology. Meanwhile, the D-Ti₃C₂T_x/(ANF/PVA) EMI shielding composite film possesses excellent flexibility and foldability.

Molecular Alignment of a Meta-Aramid on Carbon Nanotubes by In Situ Interfacial Polymerization

Molecularly organized nanocomposites of polymers and carbon nanotubes (CNTs) have great promise as high-performance materials; in particular, conformal deposition of polymers can control interfacial properties for mechanical load transfer, electrical or thermal transport, or electro/chemical transduction. However, controllability of polymer-CNT interaction remains a challenge with common processing methods that combine CNTs and polymers in melt or in solution, often leading to nonuniform polymer distribution and CNT aggregation. Here, we demonstrate CNTs within net-shape sheets can be controllably coated with a conformal coating of meta-aramid by simultaneous capillary infiltration and interfacial polymerization. We determine that π-interaction between the polymer and CNTs results in chain alignment parallel to the CNT outer wall. Subsequent nucleation and growth of the precipitated aramid forms a smooth continuous layered sheath around the CNTs. These findings motivate future investigation of mechanical properties of the resulting composites, and adaptation of the in situ polymerization method to other substrates.

Highly thermally conductive Ti3C2Tx/h-BN hybrid films via coulombic assembly for electromagnetic interference shielding

With the development of electronic equipment, heat problem and electromagnetic pollution severely affect both their functions and human health, which leads to great interests in developing materials synchronously with outstanding thermal conductivity and electromagnetic interference (EMI) shielding performance. Here, ultrathin Ti₃C₂T_x/h-BN two-dimensional (2D) heterostructure films were prepared via coulombic assembly between Ti₃C₂T_x MXene and h-BN nanosheet through ultrasonic blending. After the addition of h-BN nanosheet as thermal conductive nanofillers, the hybrid films achieved a higher value of thermal conductivity, compared to Ti₃C₂T_x composite film without h-BN. The higher thermal conductivity offered by h-BN enables the Ti₃C₂T_x/h-BN films have good potential for EMI shielding applications on wearable and portable electronic devices. When the mass ratio of Ti₃C₂T_x/h-BN is 7:3, the hybrid film with the thickness of 47.60 µm exhibited electrical conductivity of 57.67 S/cm and the maximum EMI shielding effectiveness of 37.29 dB.

High intrinsic thermally conductivity side-chain liquid crystalline polysiloxane films grafted with pendent difunctional mesogenic groups

Herein, the microscopic ordered aggregation morphologies of SCLCP films are investigated, and molecular structures with regular arrangement can increase heat transfer via suppressing the scattering of phonons, thus greatly improving the λ of SCLCPs.

A biomimetic hyaluronic acid‐silk fibroin nanofiber scaffold promoting regeneration of transected urothelium

This study was designed to investigate the regulatory effect of hyaluronic acid (HA)—coating silk fibroin (SF) nanofibers during epithelialization of urinary tract for urethral regeneration. The obtained electrospun biomimetic tubular HA‐SF nanofiber scaffold is composed of a dense inner layer and a porous outer layer in order to mimic adhesion and cavernous layers of the native tissue, respectively. A thin layer of HA‐gel coating was fixed in the inner wall to provide SF nanofibers with a dense and smooth surface nano‐topography and higher hydrophilicity. Compared with pure SF nanofibers, HA‐SF nanofibers significantly promoted the adhesion, growth, and proliferation of primary urothelial cells, and up‐regulate the expression of uroplakin‐3 (terminal differentiation keratin protein in urothelium). Using the New Zealand male rabbit urethral injury model, the scaffold composed of tubular HA‐SF nanofibers could recruit lumen and myoepithelial cells from the adjacent area of the host, rapidly reconstructing the urothelial barrier in the wound area in order to keep the urinary tract unobstructed, thereby promoting luminal epithelialization, smooth muscle bundle structural remodeling, and capillary formation. Overall, the synergistic effects of nano‐topography and biophysical cues in a biomimetic scaffold design for effective endogenous regeneration.

Mechanically Robust Flexible Multilayer Aramid Nanofibers and MXene Film for High-Performance Electromagnetic Interference Shielding and Thermal Insulation

In order to overcome the various defects caused by the limitations of solid metal as a shielding material, the development of electromagnetic shielding materials with flexibility and excellent mechanical properties is of great significance for the next generation of intelligent electronic devices. Here, the aramid nanofiber/Ti3C2Tx MXene (ANF/MXene) composite films with multilayer structure were successfully prepared through a simple alternate vacuum-assisted filtration (AVAF) process. With the intervention of the ANF layer, the multilayer-structure film exhibits excellent mechanical properties. The ANF2/MXene1 composite film exhibits a tensile strength of 177.7 MPa and a breaking strain of 12.6%. In addition, the ANF5/MXene4 composite film with a thickness of only 30 μm exhibits an electromagnetic interference (EMI) shielding efficiency of 37.5 dB and a high EMI-specific shielding effectiveness value accounting for thickness (SSE/t) of 4718 dB·cm2 g-1. Moreover, the composite film was excellent in heat-insulation performance and in avoiding light-to-heat conversion. No burning sensation was produced on the surface of the film with a thickness of only 100 μm at a high temperature of 130 °C. Furthermore, the surface of the film was only mild when touched under simulated sunlight. Therefore, our multilayer-structure film has potential significance in practical applications such as next-generation smart electronic equipment, communications, and military applications.

Mechanically strong multifunctional three-dimensional crosslinked aramid nanofiber/reduced holey graphene oxide and aramid nanofiber/reduced holey graphene oxide/polyaniline hydrogels and derived films

To endow high mechanical strength and thermal stability aramid nanofibers (ANF) with novel functionality will lead to great applications. Herein, a strategy to generate covalent bonds among components towards obtaining uniform ANF/reduced holey graphene oxide (ANF/rHGO) and ANF/rHGO/polyaniline (ANF/rHGO/PANI) hydrogels with high mechanical properties is proposed through solvent exchange gelation and subsequent hydrothermal treatment. The as-prepared ANF/rHGO and ANF/rHGO/PANI hydrogels demonstrate excellent recoverability at high compressive strength of 20.2 and 13.8 kPa with a strain of 34.4% and 30.6%, respectively, compared to a recoverability of 92.5% at a strain of ∼20% for ANF hydrogels. Moreover, ANF/rHGO and ANF/rHGO/PANI aerogels possess fast and high oil absorption capacity of 38.9-64.1 g g^-1 and 24.5-44.0 g g^-1, respectively. ANF/rHGO and ANF/rHGO/PANI films obtained after vacuum-drying exhibit a high tensile strength of 121.4 and 95.5 MPa, respectively. Additionally, ANF/rHGO/PANI thin films present good selective absorption of visible light by controlling the doping level of PANI. ANF/rHGO/PANI aerogel films prepared by freeze-drying are assembled into flexible solid-state symmetric supercapacitors and deliver a favorable specific capacitance of 200 F g^-1, a desirable capacitance retention of 98.9% after 2500 mechanical bending cycles and an approximately 100% capacitance retention even after keeping tensile force for 15 h. The as-prepared hydrogels, aerogels and derived films with such excellent performances are promising for applications in oil pollution removal, optical filters and flexible load-bearing energy storage devices.

Wood-Derived Composites with High Performance for Thermal Management Applications

Fabricating advanced polymer composites with remarkable mechanical and thermal conductivity performances is desirable for developing advanced devices and equipment. In this study, a novel strategy to prepare anisotropic wood-based scaffolds with a naturally aligned microchannel structure from balsa wood is demonstrated. The wood microchannels were coated with polydopamine-surface-modified small graphene oxide (PGO) nanosheets via assembly. The highly aligned porous microstructures, with thin wood cell walls and large voids along the cellulose microchannels, allow polymers to enter, resulting in the fabrication of the wood-polymer nanocomposite. The tensile stiffness and strength of the resulting nanocomposite reach 8.10 GPa and 90.3 MPa with a toughness of 5.0 MJ m^-3. The thermal conductivity of the nanocomposite is improved significantly by coating a PGO layer onto the wood scaffolds. The nanocomposite exhibits not only ultrahigh thermal conductivity (in-plane about 5.5 W m^-1 K^-1 and through-plane about 2.1 W m^-1 K^-1) but also satisfactory electrical insulation (volume resistivity of about 10¹⁵ Ω·cm). Therefore, the results provide a strategy to fabricate thermal management materials with excellent mechanical properties.

Advances in Studies of Boron Nitride Nanosheets and Nanocomposites for Thermal Transport and Related Applications

Hexagonal boron nitride (h-BN) and exfoliated nanosheets (BNNs) not only resemble their carbon counterparts graphite and graphene nanosheets in structural configurations and many excellent materials characteristics, especially the ultra-high thermal conductivity, but also offer other unique properties such as being electrically insulating and extreme chemical stability and oxidation resistance even at elevated temperatures. In fact, BNNs as a special class of 2-D nanomaterials have been widely pursued for technological applications that are beyond the reach of their carbon counterparts. Highlighted in this article are significant recent advances in the development of more effective and efficient exfoliation techniques for high-quality BNNs, the understanding of their characteristic properties, and the use of BNNs in polymeric nanocomposites for thermally conductive yet electrically insulating materials and systems. Major challenges and opportunities for further advances in the relevant research field are also discussed.

Hyaluronic acid-functionalized poly-lactic acid (PLA) microfibers regulate vascular endothelial cell proliferation and phenotypic shape expression

This work was designed to evaluate the efficacy of hyaluronic acid (HA) functionalized tubular poly-lactic acid (PLA) microfibers in directing the luminal pre-endothelialization of vascular endothelial cells (ECs). Tubular HA/PLA microfibers with hierarchical architecture were prepared by electrospinning and chemical cross-linking process. A layer of HA microfibrous film coating was fixed on the inner wall surface of the tubular HA/PLA microfibers, resulting in higher anisotropy wettability and relatively lower surface energy and roughness. We confirmed that HA coating on PLA microfibers surface have reduced hemolytic activity and coagulation degree. Mouse vascular ECs exhibited surface-dependent differences in cell elongation and proliferation (HA/PLA > PLA). Compared with PLA microfibers, the gene expression levels of platelet EC adhesion molecule-1 (PECAM-1/CD31) and vascular endothelial growth factor (VEGF) in ECs of HA/PLA microfibers surface were up-regulated. Immunostaining analysis revealed that the surface of HA/PLA nanofibers supported the expression of mature vascular EC phenotype CD31 protein. In vitro co-culture analysis showed that the luminal pre-endothelialization induced vascular smooth muscle cells (SMCs) to maintain their phenotypic shape and establish natural behavior patterns in the hierarchical tubular scaffold. These studies indicate that the biophysical cues of scaffolds are potent regulators of vascular EC endothelialization.

Robust Biomimetic Nacreous Aramid Nanofiber Composite Films with Ultrahigh Thermal Conductivity by Introducing Graphene Oxide and Edge-Hydroxylated Boron Nitride Nanosheet

Dielectric materials with excellent thermally conductive and mechanical properties can enable disruptive performance enhancement in the areas of advanced electronics and high-power devices. However, simultaneously achieving high thermal conductivity and mechanical strength for a single material remains a challenge. Herein, we report a new strategy for preparing mechanically strong and thermally conductive composite films by combining aramid nanofibers (ANFs) with graphene oxide (GO) and edge-hydroxylated boron nitride nanosheet (BNNS-OH) via a vacuum-assisted filtration and hot-pressing technique. The obtained ANF/GO/BNNS film exhibits an ultrahigh in-plane thermal conductivity of 33.4 Wm⁻¹ K⁻¹ at the loading of 10 wt.% GO and 50 wt.% BNNS-OH, which is 2080% higher than that of pure ANF film. The exceptional thermal conductivity results from the biomimetic nacreous “brick-and-mortar” layered structure of the composite film, in which favorable contacting and overlapping between the BNNS-OH and GO is generated, resulting in tightly packed thermal conduction networks. In addition, an outstanding tensile strength of 93.3 MPa is achieved for the composite film, owing to the special biomimetic nacreous structure as well as the strong π−π interactions and extensive hydrogen bonding between the GO and ANFs framework. Meanwhile, the obtained composite film displays excellent thermostability (T_d = 555 °C, T_g > 400 °C) and electrical insulation (4.2 × 10¹⁴ Ω·cm). We believe that these findings shed some light on the design and fabrication of multifunctional materials for thermal management applications.

Bioinspired Dielectric Film with Superior Mechanical Properties and Ultrahigh Electric Breakdown Strength Made from Aramid Nanofibers and Alumina Nanoplates

Materials with excellent thermal stability, mechanical, and insulating properties are highly desirable for electrical equipment with high voltage and high power. However, simultaneously integrating these performance portfolios into a single material remains a great challenge. Here, we describe a new strategy to prepare composite film by combining one-dimensional (1D) rigid aramid nanofiber (ANF) with 2D alumina (Al₂O₃) nanoplates using the carboxylated chitosan acting as hydrogen bonding donors as well as soft interlocking agent. A biomimetic nacreous ‘brick-and-mortar’ structure with a 3D hydrogen bonding network is constructed in the obtained ANF/chitosan/Al₂O₃ composite films, which provides the composite films with exceptional mechanical and dielectric properties. The ANF/chitosan/Al₂O₃ composite film exhibits an ultrahigh electric breakdown strength of 320.1 kV/mm at 15 wt % Al₂O₃ loading, which is 50.6% higher than that of the neat ANF film. Meanwhile, a large elongation at break of 17.22% is achieved for the composite film, integrated with high tensile strength (~233 MPa), low dielectric loss (<0.02), and remarkable thermal stability. These findings shed new light on the fabrication of multifunctional insulating materials and broaden their practical applications in the field of advanced electrics and electrical devices.

Application of Aramid Nanofibers in Nanocomposites: A Brief Review

The diameter of fibers is a critical factor in determining their final applications. When the diameter of aramid fibers changes from microns to nanoscale, its range of applications will be greatly extended. In this short review, the preparation of aramid nanofibers (ANFs) with diameters from ten nanometers to more than one hundred nanometers is introduced. Due to their excellent mechanical properties and their chemical and thermal stability, ANFs have been widely used as novel nanomaterials and composited with other materials, mainly for use in reinforced composites, energy storage, filtration and adsorption, biomedicine and electromagnetic fields. In this short review, the application of ANFs and their composites during the last 10 years is concisely summarized and a brief perspective on ANFs and their composites is also presented.