Influence of Fe and Ni Doping on the OER Performance at the Co3O4(001) Surface: Insights from DFT+U Calculations

Tuning Octahedron Sites of CoV2O4 via Cationic Competition for Efficient Oxygen Evolution Reaction

Doping transition metal oxide spinels with metal ions represents a significant strategy for optimizing the electronic structure of electrocatalysts. Herein, a bimetallic Fe and Ru doping strategy to fine-tune the crystal structure of CoV2O4 spinel for highly enhanced oxygen evolution reaction (OER) is presented performance. The incorporation of Fe and Ru is observed at octahedral sites within the CoV2O4 structure, effectively modulating the electronic configuration of Co. Density functional theory calculations have confirmed that Fe acts as a novel reactive site, replacing V. Additionally, the synergistic effect of Fe, Co, and Ru effectively optimizes the Gibbs free energy of the intermediate species, reduces the reaction energy barrier, and accelerates the kinetics toward OER. As expected, the best-performing CoVFe0.5Ru0.5O4 displays a low overpotential of 240 mV (@10 mA cm-2) and a remarkably low Tafel slope of 38.9 mV dec-1, surpassing that of commercial RuO2. Moreover, it demonstrates outstanding long-term durability lasting for 72 h. This study provides valuable insights for the design of highly active polymetallic spinel electrocatalysts for energy conversion applications.

Selective Activation of Lattice Oxygen Site Through Coordination Engineering to Boost the Activity and Stability of Oxygen Evolution Reaction

Although Ru-based materials are among the outstanding catalysts for the oxygen evolution reaction (OER), the instability issue still haunts them and impedes the widespread application. The instability of Ru-based OER catalysts is generally ascribed to the formation of soluble species through the over-oxidation of Ru and structural decomposition caused by involvement of lattice oxygen. Herein, an effective strategy of selectively activating the lattice oxygen around Ru site is proposed to improve the OER activity and stability. Our synthesized spinel-type electrocatalyst of Ru and Zn co-doped Co3O4 showed an ultralow overpotential of 172 mV at 10 mA cm-2 and a long-term stability reaching to 100 hours at 10 mA cm-2 for alkaline OER. The experimental results and theoretical simulations demonstrated that the lattice oxygen site jointly connected with the octahedral Ru and tetrahedral Zn atoms became more active than other oxygen sites near Ru atom, which further lowered the reaction energy barriers and avoided generating excessive oxygen vacancies to enhance the structural stability of Ru sites. The findings hope to provide a new perspective to improve the catalytic activity of Ru-incorporated OER catalysts and the stability of lattice-oxygen-mediated mechanism.

Surface Reconstruction for Selective Oxidation of Tetrahydroisoquinoline

Integration of hydrogen evolution with the oxidation of organic substances in one electrochemical system is highly desirable. However, achieving selective oxidation of organic substances in the integrated system is still highly challenging. In this study, a phosphorylated NiMoO4 nanoneedle-like array was designed as the catalytic active electrode for the integration of highly selective electrochemical dehydrogenation of tetrahydroisoquinolines (THIQs) with hydrogen production. The leaching of anions, including MoO42- and PO43-, facilitates the reconstruction of the catalyst. As a result, nickel oxyhydroxides with the doping of PO43- and richness of defects are in situ formed. In situ Raman and density functional theory calculations have shown that the high catalytic activity is attributed to the in situ formed PO43- involved NiOOH substance. In the dehydrogenation process, the involved C-H bond but not the N-H bond is first destroyed. A two-electrode system was then fabricated with the optimized electrode that shows a benchmark current density of 10 mA cm-2 at 1.783 V, providing a yield of 70% for dihydroisoquinolines. A robust stability was also shown for this integrated electrochemical system. The understanding of the reconstruction behavior and the achievement of selective dehydrogenation will provide some hints for electrochemical synthesis.

Exploring Cu-Doped Co3O4 Bifunctional Oxygen Electrocatalysts for Aqueous Zn-Air Batteries

The efficiency of oxygen electrocatalysis is a key factor in diverse energy domain applications, including the performance of metal-air batteries, such as aqueous Zinc (Zn)-air batteries. We demonstrate here that the doping of cobalt oxide with optimal amounts of copper (abbreviated as Cu-doped Co3O4) results in a stable and efficient bifunctional electrocatalyst for oxygen reduction (ORR) and evolution (OER) reactions in aqueous Zn-air batteries. At high Cu-doping concentrations (≥5%), phase segregation occurs with the simultaneous presence of Co3O4 and copper oxide (CuO). At Cu-doping concentrations ≤5%, the Cu ion resides in the octahedral (Oh) site of Co3O4, as revealed by X-ray diffraction (XRD)/Raman spectroscopy investigations and molecular dynamics (MD) calculations. The residence of Cu@Oh sites leads to an increased concentration of surface Co3+-ions (at catalytically active planes) and oxygen vacancies, which is beneficial for the OER. Temperature-dependent magnetization measurements reveal favorable d-orbital configuration (high eg occupancy ≈ 1) and a low → high spin-state transition of the Co3+-ions, which are beneficial for the ORR in the alkaline medium. The influence of Cu-doping on the ORR activity of Co3O4 is additionally accounted in DFT calculations via interactions between solvent water molecules and oxygen vacancies. The application of the bifunctional Cu-doped (≤5%) Co3O4 electrocatalyst resulted in an aqueous Zn-air battery with promising power density (=84 mW/cm2), stable cyclability (over 210 cycles), and low charge/discharge overpotential (=0.92 V).

Role of Fe decoration on the oxygen evolving state of Co3O4 nanocatalysts

The production of green hydrogen through alkaline water electrolysis is the key technology for the future carbon-neutral industry. Nanocrystalline Co3O4 catalysts are highly promising electrocatalysts for the oxygen evolution reaction and their activity strongly benefits from Fe surface decoration. However, limited knowledge of decisive catalyst motifs at the atomic level during oxygen evolution prevents their knowledge-driven optimization. Here, we employ a variety of operando spectroscopic methods to unveil how Fe decoration increases the catalytic activity of Co3O4 nanocatalysts as well as steer the (near-surface) active state formation. Our study shows a link of the termination-dependent Fe decoration to the activity enhancement and a significantly stronger Co3O4 near-surface (structural) adaptation under the reaction conditions. The near-surface Fe- and Co-O species accumulate an oxidative charge and undergo a reversible bond contraction during the catalytic process. Moreover, our work demonstrates the importance of low coordination surface sites on the Co3O4 host to ensure an efficient Fe-induced activity enhancement, providing another puzzle piece to facilitate optimized catalyst design.

Three-dimensional ordered macroporous design of heterogeneous cobalt-iron phosphides as oxygen evolution electrocatalyst

Oxygen evolution reaction (OER) plays a key role in electrochemical conversion, which needs efficient and economical electrocatalyst to boost its kinetics for large-scale application. Herein, a bimetallic CoP/FeP2heterostructure with a three-dimensional ordered macroporous structure (3DOM-CoP/FeP2) was synthesized as an OER catalyst to demonstrate a heterogeneous engineering induction strategy. By adjusting the electron distribution and producing a lot of active sites, the heterogeneous interface enhances catalytic performance. High specific surface area is provided by the 3DOM structure. Additionally, at the solid-gas-electrolyte threephase interface, the electrocatalytic reaction exhibits good mass transfer.In situRaman spectroscopy characterization revealed that FeOOH and CoOOH reconstructed from CoP/FeP2were the true OER active sites. Consequently, the 3DOM-CoP/FeP2demonstrates superior OER activity with a low overpotentials of 300/420 mV at 10/100 mA cm-2and meritorious OER durability. It also reveals promising performance as the overall water splitting anode.

Laser-Ironing Induced Capping Layer on Co-ZIF-L Promoting In Situ Surface Modification to High-Spin Oxide-Carbon Hybrids on the "Real Catalyst" for High OER Activity and Stability

Enhancing electrocatalytic performance through structural and compositional engineering attracts considerable attention. However, most materials only function as pre-catalysts and convert into "real catalysts" during electrochemical reactions. Such transition involves dramatic structural and compositional changes and disrupts their designed properties. Herein, for the first time, a laser-ironing (LI) approach capable of in-situ forming a laser-ironing capping layer (LICL) on the Co-ZIF-L flakes is developed. During the oxygen evolution reaction (OER) process, the LICL sustains the leaf-like morphology and promotes the formation of OER-active Co3 O4 nanoclusters with the highest activity and stability. In contrast, the pristine and conventional heat-treated Co-ZIF-Ls both collapse and transform to less active CoOOH. The density functional theory (DFT) calculations pinpoint the importance of the high spin (HS) states of Co ions and the narrowed band gap in Co3 O4 nanoclusters. They enhance the OER activity by promoting spin-selected electron transport, effectively lowering the energy barrier and realizing a spontaneous O2 -releasing step that is the potential determining step (pds) in CoOOH. This study presents an innovative approach for modulating both structural and compositional evolutions of electrocatalysts during the reaction, sustaining stability with high performance during dynamic electrochemical reactions, and providing new pathways for facile and high-precision surface microstructure control.

Multiple synergies on cobalt-based spinel oxide nanowires for electrocatalytic oxygen evolution

Cobalt-based spinel oxides have excellent oxygen evolution reaction (OER) activities and are cheap to produce; however, they have limited commercial applications due to their poor electrical conductivities and weak stabilities. Herein, we soaked Co3-xNixO4 nanowires in NaBH4 solutions, which endowed Co3-xNixO4 with significant oxygen vacancy content and decorated BOx motifs outside the Co3-xNixO4 nanowires. X-ray photoelectron spectroscopy and in situ Raman data suggest that these evolutions improved the conductivity, hydrophilicity, and increased active sites of the spinel oxides, which synergistically boosted their overall OER performances. This improved performance made the optimized BOx-covered Co2.1Ni0.9O4 nanowires generate a current density of 10 mA cm-2 when used for the OER at an overpotential of only 307 mV, maintaining excellent stability at 50 mA cm-2 for 24 h. This study provides a facile method for designing cobalt-based spinel oxide OER catalysts.

RuO2 Catalysts for Electrocatalytic Oxygen Evolution in Acidic Media: Mechanism, Activity Promotion Strategy and Research Progress

Proton Exchange Membrane Water Electrolysis (PEMWE) under acidic conditions outperforms alkaline water electrolysis in terms of less resistance loss, higher current density, and higher produced hydrogen purity, which make it more economical in long-term applications. However, the efficiency of PEMWE is severely limited by the slow kinetics of anodic oxygen evolution reaction (OER), poor catalyst stability, and high cost. Therefore, researchers in the past decade have made great efforts to explore cheap, efficient, and stable electrode materials. Among them, the RuO2 electrocatalyst has been proved to be a major promising alternative to Ir-based catalysts and the most promising OER catalyst owing to its excellent electrocatalytic activity and high pH adaptability. In this review, we elaborate two reaction mechanisms of OER (lattice oxygen mechanism and adsorbate evolution mechanism), comprehensively summarize and discuss the recently reported RuO2-based OER electrocatalysts under acidic conditions, and propose many advanced modification strategies to further improve the activity and stability of RuO2-based electrocatalytic OER. Finally, we provide suggestions for overcoming the challenges faced by RuO2 electrocatalysts in practical applications and make prospects for future research. This review provides perspectives and guidance for the rational design of highly active and stable acidic OER electrocatalysts based on PEMWE.

Enhanced Urea Oxidation Electrocatalytic Activity by Synergistic Cobalt and Nickel Mixed Oxides

Exploring reactive and selective Ni-based electrocatalysts for the urea oxidation reaction (UOR) is crucial for developing urea-related energy conversion technologies. Herein, synergistic interactions in Ni/Co mixed oxides/hydroxides enhanced the UOR with low onset potential, fast reaction kinetics, and good selectivity against the oxygen evolution reaction (OER). Our electrochemical measurements and theoretical calculations signified the collaborative interaction of Ni/Co mixed oxide/hydroxide heterostructures to enhance UOR activity. Our results showed that Ni3+ species, formed at high anodic potential, produced a high anodic current primarily from unwanted OER. Instead, the Ni/Co heterostructures with dominant Ni2+ and Co3+ species remained stable at low anodic potential and exhibited anodic current exclusively attributed to UOR. This work highlights the importance of tuning valence charges for designing high-performance and selective UOR electrocatalysts to benefit the environmental remediation of urea runoff and enable urea electrolysis for hydrogen production by replacing conventional OER with UOR at the anode.

Review of Carbon Support Coordination Environments for Single Metal Atom Electrocatalysts (SACS)

This topical review focuses on the distinct role of carbon support coordination environment of single-atom catalysts (SACs) for electrocatalysis. The article begins with an overview of atomic coordination configurations in SACs, including a discussion of the advanced characterization techniques and simulation used for understanding the active sites. A summary of key electrocatalysis applications is then provided. These processes are oxygen reduction reaction (ORR), oxygen evolution reaction (OER), hydrogen evolution reaction (HER), nitrogen reduction reaction (NRR), and carbon dioxide reduction reaction (CO2 RR). The review then shifts to modulation of the metal atom-carbon coordination environments, focusing on nitrogen and other non-metal coordination through modulation at the first coordination shell and modulation in the second and higher coordination shells. Representative case studies are provided, starting with the classic four-nitrogen-coordinated single metal atom (MN4 ) based SACs. Bimetallic coordination models including homo-paired and hetero-paired active sites are also discussed, being categorized as emerging approaches. The theme of the discussions is the correlation between synthesis methods for selective doping, the carbon structure-electron configuration changes associated with the doping, the analytical techniques used to ascertain these changes, and the resultant electrocatalysis performance. Critical unanswered questions as well as promising underexplored research directions are identified.

Crystal-facet-dependent surface transformation dictates the oxygen evolution reaction activity in lanthanum nickelate

Electrocatalysts are the cornerstone in the transition to sustainable energy technologies and chemical processes. Surface transformations under operation conditions dictate the activity and stability. However, the dependence of the surface structure and transformation on the exposed crystallographic facet remains elusive, impeding rational catalyst design. We investigate the (001), (110) and (111) facets of a LaNiO3-δ electrocatalyst for water oxidation using electrochemical measurements, X-ray spectroscopy, and density functional theory calculations with a Hubbard U term. We reveal that the (111) overpotential is ≈ 30-60 mV lower than for the other facets. While a surface transformation into oxyhydroxide-like NiOO(H) may occur for all three orientations, it is more pronounced for (111). A structural mismatch of the transformed layer with the underlying perovskite for (001) and (110) influences the ratio of Ni2+ and Ni3+ to Ni4+ sites during the reaction and thereby the binding energy of reaction intermediates, resulting in the distinct catalytic activities of the transformed facets.

A multisite dynamic synergistic oxygen evolution reaction mechanism of Fe-doped NiOOH: a first-principles study

Changing the composition is an important way to regulate the electrocatalytic performance of the oxygen evolution reaction (OER) for metallic compounds. Clarifying the synergistic mechanism among different compositions is a key scientific problem to be solved urgently. Here, based on first-principles calculations, a Ni-O-Fe multisite dynamic synergistic reaction mechanism (MDSM) for the OER of Fe-doped NiOOH (NiFeOOH) has been discovered. Based on the MDSM, Fe/O/Ni are triggered as the active sites in turn, resulting in an overpotential of 0.33 V. The factors affecting the deprotonation, O-O coupling, and O2 desorption during the OER process are analyzed. The electron channels related to the magnetic states among Fe-O-Ni is revealed, which results in the decoupling between OER sites and the oxidation reaction sites. O-O coupling and O2 desorption are affected by ferromagnetic coupling and the instability of the lattice O during the OER process, respectively. The results give a comprehensive understanding of the active sites in NiFeOOH and provide a new perspective on the synergistic effects among different compositions in metal compounds during the OER process.

Lattice strain induced d-band centre engineering enabled pseudocapacitive energy storage in 2D hypo-hyper electronic V-NiCo2O4 for asymmetric supercapacitors

Understanding the role of fundamental structural engineering of materials in unravelling the underlying rudimentary electronic structure-dependent charge storage mechanisms is crucial for developing new strategic approaches toward high-performance electrochemical energy storage devices. Here, we demonstrate the role of strain engineering by V doping-induced lattice contraction in NiCo2O4 for increasing the energy density and power density of aqueous asymmetric hybrid supercapacitors. For application in energy storage, we demonstrate the influence of electron-deficient V4+/5+ doping in electron-rich Ni2+ sites, which has been found to result in the formation of a hypo-hyper electronically coupled cation pair causing a shift in the d-band and O 2p band centres and distortion of CoO6 octahedra. Optimization of V doping to 3 mol%, achieved by a binder-free one-step hydrothermal method, has yielded a 96% increase in specific capacitance of up to 2316 F g-1 from 1193 F g-1 in pristine materials at 1 A g-1 in a three-electrode configuration with a coulombic efficiency (η%) of 94% and a 24% increase in rate capacity. A two-fold increase in specific capacitance in the pouch cell device, fabricated with a functionalized carbon nanosphere positive electrode, has been observed for the V-doped samples at 1 A g-1 with a η% of 97% and a maximum energy density of 96.3 W h g-1 and a maximum power density of 8733.6 W g-1 which are 41% and 24.3% higher than the pristine device, respectively. Excellent cycling stability of 95.4% capacitance retention has been observed after 6000 cycles. DFT calculations have been carried out to understand the previously unexplored effect of lattice strain on charge transport and quantum capacitance, and ultimately its effect on the transition state kinetics of energy storage faradaic reaction mechanisms. The aim of this work is to establish a fresh perspective on developing a deep understanding of the fundamental electronic and structural properties of materials by drawing in concepts from descriptor models in electrocatalysis to reveal the role of lattice strain and d-band centre tailoring in enabling pseudocapacitive energy storage.

Fe and Cu Double-Doped Co3O4 Nanorod with Abundant Oxygen Vacancies: A High-Rate Electrocatalyst for Tandem Electroreduction of Nitrate to Ammonia

The electrochemical nitrate reduction reaction (NO3RR) is an attractive green alternative to the conventional Haber-Bosch method for the synthesis of NH3. However, this reaction is a tandem process that involves multiple steps of electrons and protons, posing a significant challenge to the efficient synthesis of NH3. Herein, we report a high-rate NO3RR electrocatalyst of Fe and Cu double-doped Co3O4 nanorod (Fe1/Cu2-Co3O4) with abundant oxygen vacancies, where the Cu preferentially catalyzes the rapid conversion of NO3- to NO2- and the oxygen vacancy in the Co3O4 substrate can accelerate NO2- reduction to NH3. In addition, the introduction of Fe can efficiently capture atomic H* that promotes the dynamics of NO2- to NH3, improving Faradaic efficiency of the produced NH3. Controlled experimental results show that the optimal electrocatalyst of Fe1/Cu2-Co3O4 exhibits good performance with high conversion (93.39%), Faradaic efficiency (98.15%), and ammonia selectivity (98.19%), which is significantly better than other Co-based materials. This work provides guidance for the rational design of high-performance NO3RR catalysts.

Phase Engineering and Synchrotron-Based Study on Two-Dimensional Energy Nanomaterials

In recent years, there has been significant interest in the development of two-dimensional (2D) nanomaterials with unique physicochemical properties for various energy applications. These properties are often derived from the phase structures established through a range of physical and chemical design strategies. A concrete analysis of the phase structures and real reaction mechanisms of 2D energy nanomaterials requires advanced characterization methods that offer valuable information as much as possible. Here, we present a comprehensive review on the phase engineering of typical 2D nanomaterials with the focus of synchrotron radiation characterizations. In particular, the intrinsic defects, atomic doping, intercalation, and heterogeneous interfaces on 2D nanomaterials are introduced, together with their applications in energy-related fields. Among them, synchrotron-based multiple spectroscopic techniques are emphasized to reveal their intrinsic phases and structures. More importantly, various in situ methods are employed to provide deep insights into their structural evolutions under working conditions or reaction processes of 2D energy nanomaterials. Finally, conclusions and research perspectives on the future outlook for the further development of 2D energy nanomaterials and synchrotron radiation light sources and integrated techniques are discussed.

Order-disorder engineering of RuO2 nanosheets towards pH-universal oxygen evolution

Ru-based electrocatalysts are considered promising anode catalysts towards water electrolysis due to their impressive activity under acidic conditions. Yet, caused by the collapse of the local crystalline domains and concurrent leaching of Ru species during the OER process, durability against structural degradation remains poor. Herein, we present an order-disorder structure optimization strategy, based on RuO2 nanosheets with well-defined amorphous-crystalline boundaries supported on carbon cloth (a/c-RuO2/CC), to effectively catalyze water oxidation, especially in the case of an acidic medium. Specifically, the as-prepared a/c-RuO2/CC sample has achieved a lower overpotential of 150 mV at 10 mA cm-2, a smaller Tafel slope of 47 mV dec-1, and a significantly higher durability with suppressed dissolution of Ru, with regard to its crystalline (c-RuO2/CC) and amorphous (a-RuO2/CC) counterparts. Computational simulations combined with experimental characterizations uncover that the construction of the structurally ordered-disordered boundary enables a weakened Ru-O covalency with regard to the ordered counterpart, which suppresses the leaching of active Ru species from the crystalline phase, thus enhances stability. An upshift of the d-band center in a/c-RuO2/CC relative to a-RuO2/CC reduces the energy barrier of the potential-determining step (*O → *OOH), thereby dramatically boosting activity.

Tuning the Surface Electronic Structure of Amorphous NiWO4 by Doping Fe as an Electrocatalyst for OER

Water electrolysis is considered as one of the alternative potential approaches for producing renewable energy. Due to the sluggish kinetic nature of oxygen evolution reaction (OER), it encounters a significant overpotential to achieve water electrolysis. Hence, the advancement of cost-effective transition metal-based catalysts toward water splitting has gained global attention in recent years. In this work, the doping of Fe over amorphous NiWO₄ increased the OER activity effectively and achieved stable oxygen evolution in the alkaline medium, which show better electrocatalytic activity as compared to crystalline tungstate. As NiWO₄ has poor activity toward OER in the alkaline medium, the doping of Fe³⁺ will tune the electronic structure of Ni in NiWO₄ and boost the OER activity. The as-synthesized Fe-doped amorphous NiWO₄ exhibits a low overpotential of 230 mV to achieve a current density of 10 mA cm^-2 and a lower Tafel slope value of 48 mV dec^-1 toward OER in 1.0 M KOH solution. The catalyst also exhibits long-term static stability of 30 h during chronoamperometric study. The doping of Fe improves the electronic conductivity of Ni-3d states in NiWO₄ which play a dominant role for better catalytic activity via synergistic interaction between Fe and active Ni sites. In future, these results offer an alternative route for precious metal-free catalysts in alkaline medium and can be explicitly used in various tungstate-based materials to increase the synergism between the doped atom and metal ions in tungstate-based materials for further improvement in the electrocatalytic performance.

Co3O4/CoFe2O4 Hollow Nanocube Multifunctional Nanozyme with Oxygen Vacancies for Deep-Learning-Assisted Smartphone Biosensing and Organic Pollutant Degradation

Although the application of nanozymes has been widely studied, it is still a huge challenge to develop highly active and multifunctional nanozyme catalysts with a wider application prospect. Co₃O₄/CoFe₂O₄ hollow nanocubes (HNCs) with oxygen vacancies were proposed in this study, which had a porous oxide heterostructure with CoFe₂O₄ as the core and Co₃O₄ as the shell. The Co₃O₄/CoFe₂O₄ HNCs had three enzyme activities: peroxidase-like, oxidase-like, and catalase-like. Combining XPS depth profiling with density functional theory (DFT), the catalytic mechanism of peroxidase-like activity was explored in depth, which was mainly originated from ·OH produced by the synergistic effect between the outer oxygen and inner oxygen and electron transfer between Co and Fe. A colorimetry/smartphone dual sensing platform was designed based on the peroxidase-like activity. Especially, a multifunctional intelligent sensing platform based on deep learning-YOLO v3 algorithm-assisted smartphone was constructed to realize real-time and rapid in situ detection of l-cysteine, norfloxacin, and zearalenone. Surprisingly, the detection limit of norfloxacin was low at 0.015 μM, which was better than that of the newly published detection method in the field of nanozymes. Meanwhile, the detection mechanism of l-cysteine and norfloxacin was successfully investigated by in situ FTIR. In fact, it also showed outstanding applications in detecting l-cysteine in the food environment and norfloxacin in drugs. Furthermore, Co₃O₄/CoFe₂O₄ HNCs also could degrade 99.24% of rhodamine B, along with good reusability even after 10-cycle runs. Therefore, this work provided an in-depth understanding of the synergistic effect between the outer and inner oxygen in the reaction mechanism and an efficient method for establishing a deep-learning-assisted intelligent detection platform. In addition, this research also offered a good guideline for the further development and construction of nanozyme catalysts with multienzyme activities and multifunctional applications.

Effect of Cu-Doped Co-Mn Spinel for Boosting Low-Temperature NO Reduction by CO: Exploring the Structural Properties, Performance, and Mechanisms

Cobalt-manganese spinel catalysts performed unsatisfactory activity at low-temperature and narrow reaction temperature window, which greatly limited the application in NO reduction by CO. Herein, we synthesize a series of Cu-doped CoMn₂O₄ catalysts and apply to NO reduction by CO. The Cu_0.3Co_0.7Mn₂O₄ exhibited superior catalytic performance, reaching 100% NO conversion and 80% N₂ selectivity at 250 °C. Detailed structural analysis showed that the introduced Cu replaces some Co in tetrahedral coordination to induce a strong synergistic effect between different metals. This endows the catalyst with the promotion of both electron transfer and oxygen vacancy generation on the catalyst surface. Importantly, the reaction mechanism and pathway were further revealed by in situ diffusion Fourier transform infrared spectroscopy (DRIFTS) and density functional theory (DFT) calculations. The results indicated that the cycle of oxygen vacancy mainly determines the catalytic activity of NO reduction by CO. Notably, Cu doping significantly lowered the energy barrier of the rate-determining step (*CO + O → *O_v + CO₂), facilitating the desorption of the CO₂ and exposing the active sites for efficient NO reduction with CO. This work offers an effective way for designing the catalyst in NO reduction by CO and provides a reference for exploring the catalytic mechanism of the reaction.

Flexible electrochemical sensor with Fe/Co bimetallic oxides for sensitive analysis of glucose in human tears

The construction of uniformly dispersed structure with abundant active sites is crucial for fast electron transport and advancing electrocatalytic reactions. Herein, Fe_xCo_yO₄-rGO was prepared by depositing Fe and Co bimetallic oxides in-situ on reduced graphene oxide through a simple process combined hydrothermal reaction and calcination. Fe was elaborately introduced into the synthesis of metal oxides to alleviate the aggregation of cobalt oxides and obtain nanocomposites with homogeneously structured and abundant redox sites, and the bimetallic oxides nanomaterials had enhanced electrocatalysis under the synergistic effect. The flexible electrode prepared from Fe_xCo_yO₄-rGO exhibited excellent detection performance for glucose with a detection limit down low to 0.07 μM and a sensitivity of 1510 μM cm^-2 mA^-1. The adoption of flexible substrates improved the wearability of the electrode and broadened its practicality for detecting biomarkers on the skin surface. The constructed sensor was successfully used in the dynamic analysis of glucose content in tears, and the results were highly consistent with the test outcome of a commercial test kit, demonstrating its application prospects in non-invasive epidermal diabetes mellitus diagnosis.

Is It Possible to Restrain OER on Simple Carbon Electrodes to Efficiently Electrooxidize Organic Pollutants?

This paper presents a comparative analysis of three carbon-based electrodes: bare multiwalled carbon nanotubes (MWCNT), SnO2/MWCNT, and PbO2/graphene-nanoribbons (PbO2/GNR) composites, as anodes for the electrooxidative degradation of Rhodamine B as a model organic pollutant. Anodic electrooxidation of Rhodamine B was performed on all three electrodes, and the decolorization efficiency was found to increase in the order MWCNT < PbO2/GNR < SnO2/MWCNT. The electrodes were characterized by X-ray photoelectron spectroscopy (XPS) and linear sweep voltammetry (LSV). It was proposed that, in the 0.1 M Na2SO4 applied as electrolyte, observed decolorization mainly occurs in the interaction of Rhodamine B with OH radical adsorbed on the anode. Finally, the obtained results were complemented with Density Functional Theory (DFT) calculations of OH-radical interaction with appropriate model surfaces: graphene(0001), SnO2(001), and PbO2(001). It was found that the stabilization of adsorbed OH-radical on metal oxide spots (SnO2 or PbO2) compared to carbon is responsible for the improved efficiency of composites in the degradation of Rhodamine B. The observed ability of metal oxides to improve the electrooxidative potential of carbon towards organic compounds can be useful in the future design of appropriate anodes.

Vanadium-Incorporated CoP2 with Lattice Expansion for Highly Efficient Acidic Overall Water Splitting

A proton exchange membrane water electrolyzer (PEMWE) in acidic medium is a hopeful scenario for hydrogen production using renewable energy, but the grand challenge lies in substituting noble-metal catalysts. Herein, a robust electrocatalyst of V-CoP₂ porous nanowires arranged on a carbon cloth is successfully fabricated by incorporating vanadium into the CoP₂ lattice. Structural characterizations and theoretical analysis indicate that lattice expansion of CoP₂ caused by V incorporation results in the upshift of the d-band center, which is conducive to hydrogen adsorption for boosting the hydrogen evolution reaction (HER). Besides, V promotes surface reconstruction to generate a thicker Co₃ O₄ layer with an oxygen vacancy that enhances acid-corrosion resistance and optimizes the adsorption of water and oxygen-containing species, thus improving activity and stability toward the oxygen evolution reaction (OER). Accordingly, it presents a superior acidic overall water splitting activity (1.47 V@10 mA cm^-2 ) to Pt-C/CC||RuO₂ /CC (1.59 V@10 mA cm^-2 ), and remarkable stability. This work proposes a new route to design efficient non-noble metal electrocatalysts for PEMWE.

A Fe-doped Co-oxide Electrocatalyst Synthesized Through Post-Modification Method Toward Advanced Water Oxidation

In the context of the ever-increasing energy crisis, electrocatalytic water splitting has attracted widespread attention as an effective means to provide clean energy. However, the oxygen evolution reaction (OER), which...

A novel monoclinic metal oxide catalyst for oxygen evolution reaction in alkaline media

The main bottleneck of electrolytic water for hydrogen production in alkaline media is the oxygen evolution reaction (OER) involving four-electron transfer. Designing highly efficient OER catalysts is attractive to accelerate...

Ce-Substituted Spinel CuCo2O4 Quantum Dots with High Oxygen Vacancies and Greatly Improved Electrocatalytic Activity for Oxygen Evolution Reaction

Exploring effective electrocatalysts for oxygen evolution reaction (OER) is a crucial requirement of many energy storage and transformation systems, involving fuel cells, water electrolysis, and metal-air batteries. Transition-metal oxides (TMOs) have attracted much attention to OER catalysts because of their earth abundance, tunable electronic properties, and so forth. Defect engineering is a general and the most important strategy to tune the electronic structure and control size, and thus improve their intrinsic activities. Herein, OER performance on spinel CuCo₂O₄ was greatly enhanced through cation substitution and size reduction. Ce-substituted spinel CuCe_δCo_2-δO_x (δ = 0.45, 0.5 and 0.55) nanoparticles in the quantum dot scale (2-8 nm) were synthesized using a simple and facile phase-transfer coprecipitation strategy. The as-prepared samples were highly dispersed and have displayed a low overpotential of 294 mV at 10 mA·cm^-2 and a Tafel slope of 57.5 mV·dec^-1, which outperform commercial RuO₂ and the most high-performance analogous catalysts reported. The experimental and calculated results all confirm that Ce substitution with an appropriate content can produce rich oxygen vacancies, tune intermediate absorption, consequently lower the energy barrier of the determining step, and greatly enhance the OER activity of the catalysts. This work not only provides advanced OER catalysts but also opens a general avenue to understand the structure-activity relationship of pristine TMO catalysts deeply in the quantum dot scale and the rational design of more efficient OER catalysts.

Synergistic Effects of Co and Fe on the Oxygen Evolution Reaction Activity of LaCox Fe1-x O3

In a combined experimental and theoretical study we assess the role of Co incorporation on the OER activity of LaCo_xFe_1−xO₃. Phase pure perovskites were synthesized up to x=0.300 in 0.025/0.050 steps. HAADF STEM and EDX analysis points towards FeO₂‐terminated (001)‐facets in LaFeO₃, in accordance with the stability diagram obtained from density functional theory calculations with a Hubbard U term (DFT+U). Linear sweep voltammetry conducted in a rotating disk electrode setup shows a reduction of the OER overpotential and a nonmonotonic trend with x, with double layer capacitance measurements indicating an intrinsic nature of activity. This is supported by DFT+U results that show reduced overpotentials for both Fe and Co reaction sites with the latter reaching values of 0.32–0.40 V, ∼0.3 V lower than for Fe. This correlates with a stronger reduction of the binding energy difference of the *O and *OH intermediates towards an optimum value of 1.6 eV for x=0.250 , the OH deprotonation being the potential limiting step in most cases. Significant variations of the magnetic moments of both surface and subsurface Co and Fe during OER demonstrate that the beneficial effect is a result of a concerted action involving many surrounding ions, which extends the concept of the active site.

Strategies for Developing Transition Metal Phosphides in Electrochemical Water Splitting

Electrochemical water splitting involving hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) is a greatly promising technology to generate sustainable and renewable energy resources, which relies on the exploration regarding the design of electrocatalysts with high efficiency, high stability, and low cost. Transition metal phosphides (TMPs), as nonprecious metallic electrocatalysts, have been extensively investigated and proved to be high-efficient electrocatalysts in both HER and OER. In this minireview, a general overview of recent progress in developing high-performance TMP electrocatalysts for electrochemical water splitting has been presented. Design strategies including composition engineering by element doping, hybridization, and tuning the molar ratio, structure engineering by porous structures, nanoarray structures, and amorphous structures, and surface/interface engineering by tuning surface wetting states, facet control, and novel substrate are summarized. Key scientific problems and prospective research directions are also briefly discussed.

Surface-Enhanced Raman Spectroscopic Evidence of Key Intermediate Species and Role of NiFe Dual-Catalytic Center in Water Oxidation

NiFe-based electrocatalysts have attracted great interests due to the low price and high activity in oxygen evolution reaction (OER). However, the complex reaction mechanism of NiFe-catalyzed OER has not been fully explored yet. Detection of intermediate species can bridge the gap between OER performances and catalyst component/structure properties. Here, we performed label-free surface-enhanced Raman spectroscopic (SERS) monitoring of interfacial OER process on Ni₃ FeO_x nanoparticles (NPs) in alkaline medium. By using bifunctional Au@Ni₃ FeO_x core-satellite superstructures as Raman signal enhancer, we found direct spectroscopic evidence of intermediate O-O^- species. According to the SERS results, Fe atoms are the catalytic sites for the initial OH^- to O-O^- oxidation. The O-O^- species adsorbed across neighboring Fe and Ni sites experiences further oxidation caused by electron transfer to Ni^III and eventually forms O₂ product.

Surface oxygen Vacancies on Reduced Co3 O4 (100): Superoxide Formation and Ultra-Low-Temperature CO Oxidation

The activation of molecular oxygen is a fundamental step in almost all catalytic oxidation reactions. We have studied this topic and the role of surface vacancies for Co₃ O₄ (100) films with a synergistic combination of experimental and theoretical methods. We show that the as-prepared surface is B-layer terminated and that mild reduction produces oxygen single and double vacancies in this layer. Oxygen adsorption experiments clearly reveal different superoxide species below room temperature. The superoxide desorbs below ca. 120 K from a vacancy-free surface and is not active for CO oxidation while superoxide on a surface with oxygen vacancies is stable up to ca. 270 K and can oxidize CO already at the low temperature of 120 K. The vacancies are not refilled by oxygen from the superoxide, which makes them suitable for long-term operation. Our joint experimental/theoretical effort highlights the relevance of surface vacancies in catalytic oxidation reactions.

Influence of the particle size on selective 2-propanol gas-phase oxidation over Co3O4 nanospheres

Co3O4 nanospheres with a preferential (110) surface orientation showed excellent catalytic properties in the selective gas-phase oxidation of 2-propanol. A preferential Mars–van Krevelen mechanism on the Co3O4(110) surface was identified by DFT + U.