Boosting Photocatalytic Hydrogen Evolution Reaction Using Dual Plasmonic Antennas

Dual Plasmons with Bioinspired 3D Network Structure Enabling Ultrahigh Efficient Solar Steam Generation

Plasmonic nanomaterials such as Au, Ag, and Cu are widely recognized for their strong light-matter interactions, making them promising photothermal materials for solar steam generation. However, their practical use in water evaporation is significantly limited by the trade-off between high costs and poor stability. In this regard, we introduce a novel, nonmetallic dual plasmonic TiN/MoO3-x composite. This composite features a three-dimensional, urchin-like biomimetic structure, with plasmonic TiN nanoparticles embedded within a network of plasmonic MoO3-x nanorods. As a solar absorber, the TiN/MoO3-x composite achieves a high evaporation rate of ∼2.05 kg m-2 h-1 with an energy efficiency up to 106.7% under 1 sun illumination, outperforming the state-of-the-art plasmonic systems. The high photothermal stability and unique dual plasmonic nanostructure of the TiN/MoO3-x composite are demonstrated by advanced in situ laser-heating transmission electron microscopy and photon-induced near-field electron microscopy/electron energy-loss spectroscopy, respectively. This work provides new inspiration for the design of plasmonic materials.

Monitoring Hot Holes in Plasmonic Catalysis on Silver Nanoparticles by Using an Ion Label

Energetic carriers generated by localized surface plasmon resonance (LSPR) provide an efficient way to drive chemical reactions. However, their dynamics and impact on surface reactions remain unknown due to the challenge in observing hot holes. This makes it difficult to correlate the reduction and oxidation half-reactions involving hot electrons and holes, respectively. Here we detect hot holes in their chemical form, Ag(I), on a Ag surface using surface-enhanced Raman scattering (SERS) of SO32- as a hole-specific label. It allows us to determine the dynamic correlations of hot electrons and holes. We find that the equilibrium of holes is the key factor of the surface chemistry, and the wavelength-dependent plasmonic chemical anode refilling (PCAR) effect plays an important role, in addition to the LSPR, in promoting the electron transfer. This method paves the way for visualizing hot holes with nanoscale spatial resolution toward the rational design of a plasmonic catalytic platform.

Robust construction of CeNi quantum dots/Ni-MOL nanosheets for superior photocatalytic CO2 reduction

Since the intensification of global environmental pollution and energy shortages, photocatalytic CO2 reduction reaction (CO2RR) has emerged as a promising strategy to convert solar energy into clean chemical energy. Herein, we construct a robust and efficient heterojunction construction photocatalyst for CO2RR, composed of the highly reactive CeNi quantum dots (CeNi QDs) and nickel metal-organic layer (Ni-MOL) ultrathin nanosheets. This design facilitates the rapid separation of photogenerated charge carriers, as confirmed by X-ray photoelectron spectroscopy (XPS), photoluminescence spectroscopy (PL) and other characterizations. Mechanistic studies with in situ diffuse reflectance Fourier transform infrared spectroscopy (in situ DRIFTS) and the d-band center calculation indicate that the propensity of photocatalyst for CO2 absorption and CO desorption, leading to high performance and selectivity. The optimized loading amount of CeNi quantum dots and modified structure result in a CO yield of 30.53 mmol·g-1 within 6 h under irradiation. This work not only paves a new and convenient way for developing high-activity quantum dot materials for CO2RR but also exploits novel avenues to fabricate more heterojunction composites for solar energy conversion.

Facile synthesis of Zn0.5Cd0.5S nanosheets with tunable S vacancies for highly efficient photocatalytic hydrogen evolution

In order to effectively improve the separation efficiency of photogenerated charge carriers and thus the photocatalytic activity, in this work, porous Zn0.5Cd0.5S nanosheets with a controlled amount of S vacancies were prepared by a multistep chemical transformation strategy using the inorganic-organic hybrid ZnS-ethylenediamine (denoted as ZnS(en)0.5) as a hard template. The amount of S vacancies and the morphology of the Zn0.5Cd0.5S nanostructures were tailored by adjusting the hydrolysis time. Furthermore, we report the observation of S vacancies in porous Zn0.5Cd0.5S nanosheets at the atomic level using spherical aberration-corrected (Cs-aberrated) transmission electron microscopy (Cs-corrected-TEM). The results revealed that Zn0.5Cd0.5S nanosheets with S vacancies absorb more visible light and generate more electron-hole carriers due to their porous nanosheet structure. At the same time, sulfur vacancies are introduced into the Zn0.5Cd0.5S nanosheets to capture the electrons generated by the light and further extend the lifetime of the carriers. As expected, the photocatalytic activity of Zn0.5Cd0.5S nanosheets prepared by 4 h hydrolysis is 20.5 times higher than that of Zn0.5Cd0.5S(en)x intermediates. Moreover, Zn0.5Cd0.5S-4h showed excellent cycling stability. This work provides a new strategy for the optimization of Zn0.5Cd0.5S photocatalysts to improve photocatalytic hydrogen evolution.

Triple Play of Band Gap, Interband, and Plasmonic Excitations for Enhanced Catalytic Activity in Pd/HxMoO3 Nanoparticles in the Visible Region

Plasmonic photocatalysis has been limited by the high cost and scalability of plasmonic materials, such as Ag and Au. By focusing on earth-abundant photocatalyst/plasmonic materials (HxMoO3) and Pd as a catalyst, we addressed these challenges by developing a solventless mechanochemical synthesis of Pd/HxMoO3 and optimizing photocatalytic activities in the visible range. We investigated the effect of HxMoO3 band gap excitation (at 427 nm), Pd interband transitions (at 427 nm), and HxMoO3 localized surface plasmon resonance (LSPR) excitation (at 640 nm) over photocatalytic activities toward the hydrogen evolution and phenylacetylene hydrogenation as model reactions. Although both excitation wavelengths led to comparable photoenhancements, a 110% increase was achieved under dual excitation conditions (427 + 640 nm). This was assigned to a synergistic effect of optical excitations that optimized the generation of energetic electrons at the catalytic sites. These results are important for the development of visible-light photocatalysts based on earth-abundant components.

Understanding the Behaviors of Plasmon-Induced Hot Carriers and Their Applications in Photocatalysis

Photocatalysis driven by plasmon-induced hot carriers has been gaining increasing attention. Recent studies have demonstrated that plasmon-induced hot carriers can directly participate in photocatalytic reactions, leading to great enhancement in solar energy conversion efficiency, by improving the catalytic activity or changing selectivity. Nevertheless, the utilization efficiency of hot carriers remains unsatisfactory. Therefore, how to correctly understand the generation and transfer process of hot carriers, as well as accurately differentiate between the possible mechanisms, have become a key point of attention. In this review, we overview the fundamental processes and mechanisms underlying hot carrier generation and transport, followed by highlighting the importance of hot carrier monitoring methods and related photocatalytic reactions. Furthermore, possible strategies for the further characterization of plasmon-induced hot carriers and boosting their utilization efficiency have been proposed. We hope that a comprehensive understanding of the fundamental behaviors of hot carriers can aid in designing more efficient photocatalysts for plasmon-induced photocatalytic reactions.

Self-Assembled Hyperbranched Gold Nanoarrays Decode Serum United Urine Metabolic Fingerprints for Kidney Tumor Diagnosis

Serum united urine metabolic analysis comprehensively reveals the disease status for kidney diseases in particular. Thus, the precise and convenient acquisition of metabolic molecular information from united biofluids is vitally important for clinical disease diagnosis and biomarker discovery. Laser desorption/ionization mass spectrometry (LDI-MS) presents various advantages in metabolic analysis; however, there remain challenges in ionization efficiency and MS signal reproducibility. Herein, we constructed a self-assembled hyperbranched black gold nanoarray (HyBrAuNA) assisted LDI-MS platform to profile serum united urine metabolic fingerprints (S-UMFs) for diagnosis of early stage renal cell carcinoma (RCC). The closely packed HyBrAuNA afforded strong electromagnetic field enhancement and high photothermal conversion efficacy, enabling effective ionization of low abundant metabolites for S-UMF collection. With a uniform nanoarray, the platform presented excellent reproducibility to ensure the accuracy of S-UMFs obtained in seconds. When it was combined with automated machine learning analysis of S-UMFs, early stage RCC patients were discriminated from the healthy controls with an area under the curve (AUC) > 0.99. Furthermore, we screened out a panel of 9 metabolites (4 from serum and 5 from urine) and related pathways toward early stage kidney tumor. In view of its high-throughput, fast analytical speed, and low sample consumption, our platform possesses potential in metabolic profiling of united biofluids for disease diagnosis and pathogenic mechanism exploration.

High refractive index dielectric coating on plasmonic nanoantennas for strong visible light absorption in small transition metal nanoparticle reactors

A more practical model for plasmonic core@shell-satellite antenna-reactor photocatalysts is promoted. In contrast to the mainstream view, total light absorption in the Pt nanoparticle (NP) reactors can be further improved by 70% after coating a 10-nm-thick high refractive index TiO₂ shell on the large Ag antenna as a result of more Pt NPs undergoing high absorption enhancement. The enhancement effect is maximized at the electric quadrupole (EQ) resonance. Considering the high refractive index of the TiO₂ coating and the embedding of the Pt NPs, the underlying physics is addressed within classical electrodynamics, making a necessary supplement to the conventional plasmonic near-field enhancement mechanism. These findings provide a general strategy for developing novel, to the best of our knowledge, visible light photocatalysts made of transition metals directly.

Construction of Robust Iridium(III) Complex-Based Photosensitizer for Boosting Hydrogen Evolution

Developing a photosensitizer with high efficiency and long-term stability for photocatalytic hydrogen evolution is highly desirable yet remains a challenge. Herein, a novel Ir(III) complex-based photosensitizer (Ir3) bearing coumarin and triphenylamine groups is designed. Ir3 exhibits record activity and durability among reported transition metal complexes for photocatalytic hydrogen evolution, with a TON of 198,363 and a duration of 214 h. The excellent photocatalytic performance of Ir3 can be attributed to the synergistic effect of coumarin and triphenylamine, which improves the visible light absorption, charge separation, and electron transfer capacity of photosensitizers. This is an efficient and long-lived Ir(III) photosensitizer constructed on the basis of a synergistic approach, which could provide a new insight for the development of high-performance Ir(III) photosensitizers at the molecular level.

Direct S-H Evidence Revealing the Photo-electrocatalytic Hydrogen Evolution Reaction Mechanism on CdS Using Surface-Enhanced Raman Spectroscopy

Photoelectrocatalytic water splitting using metal sulfides is a promising method for green hydrogen production. However, in situ probing of the hydrogen evolution reaction (HER) on sulfides with excellent performance remains a challenge. Here, we construct Au@CdS core-shell nanoparticles to study the HER on CdS, a typical HER catalyst, by surface-enhanced Raman spectroscopy (SERS) using a "borrowing" strategy. We directly capture the spectroscopic evidence of S-H intermediate under HER condition, further verified by isotopic experiments. Moreover, the population of S-H intermediates is improved by injecting charge carriers through light illumination and the S-H bond is weakened by introducing Pt to form a Au@Pt@CdS structure to change the interfacial electronic structure, both of them resulting in significant HER performance improvement. These findings can deepen the understanding of the HER mechanism and offer strategies for designing of cost-effective HER catalyst with high performance.

Strong synergy between gold nanoparticles and cobalt porphyrin induces highly efficient photocatalytic hydrogen evolution

The reaction efficiency of reactants near plasmonic nanostructures can be enhanced significantly because of plasmonic effects. Herein, we propose that the catalytic activity of molecular catalysts near plasmonic nanostructures may also be enhanced dramatically. Based on this proposal, we develop a highly efficient and stable photocatalytic system for the hydrogen evolution reaction (HER) by compositing a molecular catalyst of cobalt porphyrin together with plasmonic gold nanoparticles, around which plasmonic effects of localized electromagnetic field, local heating, and enhanced hot carrier excitation exist. After optimization, the HER rate and turn-over frequency (TOF) reach 3.21 mol g^-1 h^-1 and 4650 h^-1, respectively. In addition, the catalytic system remains stable after 45-hour catalytic cycles, and the system is catalytically stable after being illuminated for two weeks. The enhanced reaction efficiency is attributed to the excitation of localized surface plasmon resonance, particularly plasmon-generated hot carriers. These findings may pave a new and convenient way for developing plasmon-based photocatalysts with high efficiency and stability.

Active Site Engineering on Plasmonic Nanostructures for Efficient Photocatalysis

Plasmonic nanostructures have shown immense potential in photocatalysis because of their distinct photochemical properties associated with tunable photoresponses and strong light-matter interactions. The introduction of highly active sites is essential to fully exploit the potential of plasmonic nanostructures in photocatalysis, considering the inferior intrinsic activities of typical plasmonic metals. This review focuses on active site-engineered plasmonic nanostructures with enhanced photocatalytic performance, wherein the active sites are classified into four types (i.e., metallic sites, defect sites, ligand-grafted sites, and interface sites). The synergy between active sites and plasmonic nanostructures in photocatalysis is discussed in detail after briefly introducing the material synthesis and characterization methods. Active sites can promote the coupling of solar energy harvested by plasmonic metal to catalytic reactions in the form of local electromagnetic fields, hot carriers, and photothermal heating. Moreover, efficient energy coupling potentially regulates the reaction pathway by facilitating the excited state formation of reactants, changing the status of active sites, and creating additional active sites using photoexcited plasmonic metals. Afterward, the application of active site-engineered plasmonic nanostructures in emerging photocatalytic reactions is summarized. Finally, a summary and perspective of the existing challenges and future opportunities are presented. This review aims to deliver some insights into plasmonic photocatalysis from the perspective of active sites, expediting the discovery of high-performance plasmonic photocatalysts.

Preparation of pure active water for auto-catalytic reactions performed in it

In catalyzed electrochemical reactions, a general strategy is to modify electrode materials to increase the efficiency of the reaction. From the viewpoint of environmental protection, electrochemical reactions should be performed in an inert green water phase. In this study, we report active pure liquid water (named PV), which was collected from the condensed vapor of heated gold (Au)-containing plasmon-activated water (PAW) with a distinct structure of electron-doping and reduced hydrogen bonding (HB). The resulting PV also exhibited distinct properties of the formation of stronger intermolecular HB with alcohols, and notable activities in catalytic electrochemical reactions, compared to bulk deionized water (DIW). Moreover, the measured diffusion coefficients of water increased by ca. 30% in PV solutions. Two typical electrochemical reactions significantly increased peak currents observed in oxidation-reduction cycles (ORCs) with roughening of the Au substrate and in a model of reversible oxidation-reduction reactions on a platinum (Pt) substrate. Also, PV enhanced hydrogen evolution reactions (HERs) on catalytic Pt and inert stainless steel substrates in PV-based solutions at different pH values, compared to DIW. Moreover, these activities of PV were more marked, even better than those of PAW, when PV was collected under a higher heating rate used to heat PAW. Active pure PV has emerged as a promising green solvent applicable to various chemical reactions with more efficiency.

Exploiting the LSPR effect for an enhanced photocatalytic hydrogen evolution reaction

Incorporation of plasmonic metals is one of the most widely adopted strategies for improving the photocatalytic hydrogen evolution reaction (HER) activity of semiconductor photocatalysts. This article summarizes recent advances in the development of plasmonic metal-semiconductor photocatalysts and four localized surface plasmon resonance (LSPR) driven mechanisms by which plasmonic metal nanoparticles can contribute to enhancement of HER activity. In addition, principles for maximizing the contribution of these LSPR driven mechanisms are highlighted to provide insights for future design of plasmonic metal-semiconductor photocatalysts with enhanced HER activity.

Increasing electron density by surface plasmon resonance for enhanced photocatalytic CO2 reduction

The photocatalytic CO₂ reduction reaction is a multi-electron process, which is greatly affected by the surface electron density. In this work, we synthesize Ag clusters supported on In₂O₃ plasmonic photocatalysts. The Ag-In₂O₃ compounds show remarkedly enhanced photocatalytic activity for CO₂ conversion to CO compared to pristine In₂O₃. In the absence of any co-catalyst or sacrificial agent, the CO evolution rate of optimal Ag-In₂O₃-10 is 1.56 μmol/g/h, achieving 5.38-folds higher than that of In₂O₃ (0.29 μmol/g/h). Experimental verification and DFT calculation demonstrate that electrons transfer from Ag clusters to In₂O₃ on Ag-In₂O₃ compounds. In Ag-In₂O₃ compounds, Ag clusters serving as electron donators owing to the SPR behaviour are not helpful to decline photo-induced charge recomnation rate, but can provide more electron for photocatalytic reaction. Overall, the Ag clusters promote visible-light absorption and accelerate photocatalytic reaction kinetic for In₂O₃, resulting in the photocatalytic activity enhancement of Ag-In₂O₃ compounds. This work puts insight into the function of plasmonic metal on enhancing photocatalysis performance, and provides a feasible strategy to design and fabricate efficient plasmonic photocatalysts.

Machine Learning-Aided Design of Gold Core-Shell Nanocatalysts toward Enhanced and Selective Photooxygenation

We demonstrate the use of the machine learning (ML) tools to rapidly and accurately predict the electric field as a guide for designing core-shell Au-silica nanoparticles to enhance ¹O₂ sensitization and selectivity of organic synthesis. Based on the feature importance analysis, obtained from a deep neural network algorithm, we found a general and linear dependent descriptor (θ ∝ aD^0.25t^-1, where a, D, and t are the shape constant, size of metal nanoparticles, and distance from the metal surface) for the electric field around the core-shell plasmonic nanoparticle. Directed by the new descriptor, we synthesized gold-silica nanoparticles and validated their plasmonic intensity using scanning transmission electron microscopy-electron energy loss spectroscopy (STEM-EELS) mapping. The nanoparticles with θ = 0.40 demonstrate an ∼3-fold increase in the reaction rate of photooxygenation of anthracene and 4% increase in the selectivity of photooxygenation of dihydroartemisinic acid (DHAA), a long-standing goal in organic synthesis. In addition, the combination of ML and experimental investigations shows the synergetic effect of plasmonic enhancement and fluorescence quenching, leading to enhancement for ¹O₂ generation. Our results from time-dependent density functional theory (TD-DFT) calculations suggest that the presence of an electric field can favor intersystem crossing (ISC) of methylene blue to enhance ¹O₂ generation. The strategy reported here provides a data-driven catalyst preparation method that can significantly reduce experimental cost while paving the way for designing photocatalysts for organic drug synthesis.

Plasmonic Hybrid Nanostructures in Photocatalysis: Structures, Mechanisms, and Applications

(Sun)Light is an abundantly available sustainable source of energy that has been used in catalyzing chemical reactions for several decades now. In particular, studies related to the interaction of light with plasmonic nanostructures have been receiving increased attention. These structures display the unique property of localized surface plasmon resonance, which converts light of a specific wavelength range into hot charge carriers, along with strong local electromagnetic fields, and/or heat, which may all enhance the reaction efficiency in their own way. These unique properties of plasmonic nanoparticles can be conveniently tuned by varying the metal type, size, shape, and dielectric environment, thus prompting a research focus on rationally designed plasmonic hybrid nanostructures. In this review, the term "hybrid" implies nanomaterials that consist of multiple plasmonic or non-plasmonic materials, forming complex configurations in the geometry and/or at the atomic level. We discuss the synthetic techniques and evolution of such hybrid plasmonic nanostructures giving rise to a wide variety of material and geometric configurations. Bimetallic alloys, which result in a new set of opto-physical parameters, are compared with core-shell configurations. For the latter, the use of metal, semiconductor, and polymer shells is reviewed. Also, more complex structures such as Janus and antenna reactor composites are discussed. This review further summarizes the studies exploiting plasmonic hybrids to elucidate the plasmonic-photocatalytic mechanism. Finally, we review the implementation of these plasmonic hybrids in different photocatalytic application domains such as H₂ generation, CO₂ reduction, water purification, air purification, and disinfection.

Plasma-Wind-Assisted In2S3 Preparation with an Amorphous Surface Structure for Enhanced Photocatalytic Hydrogen Production

Photocatalytic production from water is considered an effective solution to fossil fuel-related environmental concerns, and photocatalyst surface science holds a significant interest in balancing photocatalysts’ stability and activity. We propose a plasma-wind method to tune the surface properties of a photocatalyst with an amorphous structure. Theoretical calculation shows that the amorphous surface structure can cause an unsaturated coordination environment to adjust the electron distribution, forming more adsorption sites. Thus, the photocatalyst with a crystal–amorphous (C–A) interface can strengthen light absorption, harvest photo-induced electrons, and enrich the active sites, which help improve hydrogen yield. As a proof of concept, with indium sulfide (In2S3) nanosheets used as the catalyst, an impressive hydrogen production rate up to 457.35 μmol cm−2 h−1 has been achieved. Moreover, after plasma-assisted treatment, In2S3 with a C–A interface can produce hydrogen from water under natural outdoor conditions. Following a six-hour test, the rate of photocatalytic hydrogen evolution is found to be 400.50 μmol cm−2 g−1, which demonstrates that a catalyst prepared through plasma treatment is both effective and highly practical.

Effect of synthesis time on plasmonic properties of Ag dendritic nanoforests

The effects of synthesis time on the plasmonic properties of Ag dendritic nanoforests on Si substrate (Ag-DNF/Si) samples synthesized through the fluoride-assisted galvanic replacement reaction were investigated. The Ag-DNF/Si samples were characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy, reflection spectroscopy, X-ray diffraction and surface-enhanced Raman spectroscopy (SERS). The prolonged reaction time led to the growth of an Ag-DNF layer and etched Si hole array. SEM images and variations in the fractal dimension index indicated that complex-structure, feather-like leaves became coral-like branches between 30 and 60 min of synthesis. The morphological variation during the growth of the Ag DNFs resulted in different optical responses to light illumination, especially those of light harvest and energy transformation. The sample achieved the most desirable light-to-heat conversion efficiency and SERS response with a 30 min growth time. A longer synthesis time or thicker Ag-DNF layer on the Si substrate did not have superior plasmonic properties.

Dual-Functional Photocatalysis for Cooperative Hydrogen Evolution and Benzylamine Oxidation Coupling over Sandwiched-Like Pd@TiO2 @ZnIn2 S4 Nanobox

Photocatalytic hydrogen evolution (PHE) over semiconductor photocatalysts is usually constrained by the limited light-harvesting and separation of photogenerated electron-hole pairs. Most of the reported systems focusing on PHE are facilitated by consuming the photoinduced holes with organic sacrificial electron donors (SEDs). The introduction of the SEDs not only causes the environmental problem, but also increases the cost of the reaction. Herein, a dual-functional photocatalyst is developed with the morphology of sandwiched-like hollowed Pd@TiO₂ @ZnIn₂ S₄ nanobox, which is synthesized by choosing microporous zeolites with sub-nanometer-sized Pd nanoparticles (Pd NPs) embedded as the sacrificial templates. The ternary Pd@TiO₂ @ZnIn₂ S₄ photocatalyst exhibits a superior PHE rate (5.35 mmol g^-1 h^-1 ) and benzylamine oxidation conversion rate (>99%) simultaneously without adding any other SEDs. The PHE performance is superior to the reported composites of TiO₂ and ZnIn₂ S₄ , which is attributed to the elevated light capture ability induced by the hollow structure, and the enhanced charge separation efficiency facilitated by the ultrasmall sized Pd NPs. The unique design presented here holds great potential for other highly efficient cooperative dual-functional photocatalytic reactions.

Hybrid Plasmonic Nanomaterials for Hydrogen Generation and Carbon Dioxide Reduction

The successful development of artificial photosynthesis requires finding new materials able to efficiently harvest sunlight and catalyze hydrogen generation and carbon dioxide reduction reactions. Plasmonic nanoparticles are promising candidates for these tasks, due to their ability to confine solar energy into molecular regions. Here, we review recent developments in hybrid plasmonic photocatalysis, including the combination of plasmonic nanomaterials with catalytic metals, semiconductors, perovskites, 2D materials, metal-organic frameworks, and electrochemical cells. We perform a quantitative comparison of the demonstrated activity and selectivity of these materials for solar fuel generation in the liquid phase. In this way, we critically assess the state-of-the-art of hybrid plasmonic photocatalysts for solar fuel production, allowing its benchmarking against other existing heterogeneous catalysts. Our analysis allows the identification of the best performing plasmonic systems, useful to design a new generation of plasmonic catalysts.

Au-Cu2-xTe Plasmonic Heteronanostructure Photoelectrocatalysts

Semiconductor nanocrystals coupled with plasmonic Au nanoparticles have been widely studied as photoelectrocatalysts for solar water splitting. Among these, heterostructures of copper chalcogenides with Au remained a unique category for their dual plasmon character. However, while sulfides and selenides of copper have been extensively reported, heterostructures of copper tellurides with Au have not been explored. Herein, the plasmonic semiconductor Cu_2-xTe disks grown on Au nanoparticles (disk-on-dot) were explored as efficient photoelectrocatalysts for hydrogen evolution reactions (HER). This has been successfully designed by growing Cu_2-xTe disks on presynthesized Au nanoparticles under optimized reaction conditions. The resulting heterostructured nanocrystals acted as efficient photoelectrocatalysts for the H₂ evolution reaction with a low Tafel slope and less cathodic overpotential in the presence of light. Details of their synthesis, characterization, optical properties, and electrocatalytic activities are studied and reported in this letter.

Synthesis of Ni modified Au@CdS core-shell nanostructures for enhancing photocatalytic coproduction of hydrogen and benzaldehyde under visible light

The development of visible light responsive photocatalysts for simultaneous production of hydrogen (H₂) fuel and value-added chemicals is greatly promising to solve the energy and environmental issues by improving the utilization efficiency of solar energy. Herein, the three-component Ni/(Au@CdS) core-shell nanostructures were constructed by the hydrothermal synthesis followed with photodeposition. The intimate integration of plasmonic Au nanospheres and visible-light responsive CdS shells modified with Ni cocatalyst facilitated the generation and separation of electron-hole pairs as well as reduced the overpotential of hydrogen evolution. The Ni/(Au@CdS) photocatalyst exhibited excellent performance toward the selective transformation of benzyl alcohol under anaerobic conditions, and the yields of H₂ and benzaldehyde reached up to 3882 and 4242 μmol·g^-1·h^-1, respectively. The apparent quantum efficiency (AQE) was determined to be 4.09% under the irradiation of 420 nm. The systematic studies have verified the synergy of plasmonic effect and metal cocatalyst on enhancing the photocatalysis. This work highlights the desirable design and potential application of plasmonic photocatalysts for solar-driven coproduction of H₂ fuel and high-value chemicals.

Interfacial chemical bond and internal electric field modulated Z-scheme Sv-ZnIn2S4/MoSe2 photocatalyst for efficient hydrogen evolution

Construction of Z-scheme heterostructure is of great significance for realizing efficient photocatalytic water splitting. However, the conscious modulation of Z-scheme charge transfer is still a great challenge. Herein, interfacial Mo-S bond and internal electric field modulated Z-scheme heterostructure composed by sulfur vacancies-rich ZnIn₂S₄ and MoSe₂ was rationally fabricated for efficient photocatalytic hydrogen evolution. Systematic investigations reveal that Mo-S bond and internal electric field induce the Z-scheme charge transfer mechanism as confirmed by the surface photovoltage spectra, DMPO spin-trapping electron paramagnetic resonance spectra and density functional theory calculations. Under the intense synergy among the Mo-S bond, internal electric field and S-vacancies, the optimized photocatalyst exhibits high hydrogen evolution rate of 63.21 mmol∙g^-1·h^-1 with an apparent quantum yield of 76.48% at 420 nm monochromatic light, which is about 18.8-fold of the pristine ZIS. This work affords a useful inspiration on consciously modulating Z-scheme charge transfer by atomic-level interface control and internal electric field to signally promote the photocatalytic performance.