Defective NiO as a Stabilizer for Au Single-Atom Catalysts

Critical role of NiO support morphology for high activity of Au/NiO nanocatalysts in CO oxidation

The effect on catalytic behavior induced by different morphology of NiO supports has been investigated using the example of gold-catalyzed CO oxidation. Three NiO-supported nanogold consisting of nanogold deposited onto NiO nanorods (NiO-R), nanosheet (NiO-S), and nanodiscs (NiO-D) were prepared. Transmission electron microscopy(TEM)/Scanning transmission electron microscopy(STEM) investigations indicated that Au particles dominantly exposed Au(111) facets virtually independent of NiO architectures. Au/NiO-S displayed a normal Arrhenius-type behavior. Au/NiO-R and Au/NiO-D showed an atypical behavior, characterized by a U-shaped curve of activity vs. temperature, which is attributed to the carbonate accumulation on whose catalytically active sites. On Au/NiO-R, a stable CO-conversion rate of 1.78 molCO gAu -1 h-1 at 30°C was achieved, which is among the higher rates reported so far for supported Au-based systems. DRIFTS measurement identified Auδ+ species as crucial CO adsorption sites promoting CO oxidation, and the catalytic CO oxidation should obey Mars-van Krevelen (<200°C) and Eley-Rideal mechanism (>240°C).

Engineering Partially Oxidized Gold via Oleylamine Modifier as a High-Performance Anode Catalyst in a Direct Borohydride Fuel Cell

Direct borohydride fuel cell (DBFC) is considered a promising energy storage device due to its high theoretical cell voltage and energy density. For DBFC, an Au catalyst has been used as an anode for achieving an ideal eight-electron reaction. However, the poor activity of the Au catalyst for borohydride oxidation reaction (BOR) limits its large-scale application because of the weak BH4- adsorption. We found, by density functional theory calculations, that the adsorption of BH4- on the oxidized Au surface is stronger than that on the metallic Au surface, which can promote the process of the oxidation of BH4- to *BH3 during the BOR. Here, we reported an oleylamine-modified partially oxidized Au supported on carbon powder (AuC-OLA) with a stable oxidation state. The obtained catalyst delivered a high peak power density of 143 mW/cm2, which is 2 times higher than that of a commercial 40% AuC (Pretemek). The in situ Fourier transform infrared studies showed that the activity of AuC-OLA for BOR is ascribed to the enhanced adsorption for BH4- on the partially oxidized Au surface. These findings will promote the reasonable design of efficient Au electrocatalysts for DBFCs.

Isolated Ni Atoms Enable Near-Unity CH4 Selectivity for Photothermal CO2 Hydrogenation

Photothermal hydrogenation of carbon dioxide (CO2) into value-added products is an ideal solution for addressing the energy crisis and mitigating CO2 emissions. However, achieving high product selectivity remains challenging due to the simultaneous occurrence of numerous competing intermediate reactions during CO2 hydrogenation. We present a novel approach featuring isolated single-atom nickel (Ni) anchored onto indium oxide (In2O3) nanocrystals, serving as an effective photothermal catalyst for CO2 hydrogenation into methane (CH4) with a remarkable near-unity (∼99%) selectivity. Experiments and theoretical simulations have confirmed that isolated Ni sites on the In2O3 surface can effectively stabilize the intermediate products of the CO2 hydrogenation reaction and reduce the transition state energy barrier, thereby changing the reaction path to achieve ultrahigh selective methanation. This study provides comprehensive insights into the design of single-atom catalysts for the highly selective photothermal catalytic hydrogenation of CO2 to methane.

Lattice variation as a function of concentration and grain size in MgO-NiO solid solution system

The study aimed to understand how changes in crystal's size affect the lattice parameters and crystal structure of Mg1-xNixO solid solution for six X values ranging from x = 0 to x = 1. Mg1-xNixO was synthesized via two different wet-chemical techniques: the sol-gel and the microwave hydrothermal method, both followed by calcination at different temperatures of 673, 873, 1073, 1273 and 1473 K. As annealing caused grain growth, the varied temperature range allowed to examine a wide range of grain sizes. The lattice parameters and x values were determined from XRD (X-ray diffraction) peak positions and intensities respectively. The grain size was evaluated by XRD line profile analysis and supported by SEM (scanning electron microscope) observations. At the temperatures of 673 and 873 K grain size was in the nanometric range and from 1073 K and above grain size was in the micrometric range. A non-monotonic lattice variation versus grain size was found for each concentration. When grain size decreased there was a slight contraction, however for grain size in the nanometric range there was a severe lattice expansion. Both lattice parameter changes were explained by two effects acting together: contraction due to surface stress and expansion due to weakening of the ionic bonding at nanocrystalline particles. In this current research study, the lattice parameter was mapped in two dimensions: concentration and grain size. The findings of this study provided valuable insights into the lattice variation in the MgO-NiO solid solution system.

Recovering palladium and gold by peroxydisulfate-based advanced oxidation process

Palladium (Pd) and gold (Au) are the most often used precious metals (PMs) in industrial catalysis and electronics. Green recycling of Pd and Au is crucial and difficult. Here, we report a peroxydisulfate (PDS)-based advanced oxidation process (AOPs) for selectively recovering Pd and Au from spent catalysts. The PDS/NaCl photochemical system achieves complete dissolution of Pd and Au. By introducing Fe(II), the PDS/FeCl2·4H2O solution functioned as Fenton-like system, enhancing the leaching efficiency without xenon (Xe) lamp irradiation. Electron paramagnetic resonance (EPR), 18O isotope tracing experiments, and density functional theory calculations revealed that the reactive oxidation species of SO4·-, ·OH, and Fe(IV)═O were responsible for the oxidative dissolution process. Lixiviant leaching and one-step electrodeposition recovered high-purity Pd and Au. Strong acids, poisonous cyanide, and volatile organic solvents were not used during the whole recovery, which enables an efficient and sustainable precious metal recovery approach and encourage AOP technology for secondary resource recycling.

Electron Deficient Ir-O Bonds Promote Heterogeneous Ir-Catalyzed Anti-Markovnikov Hydroboration of Alkenes under Mild Neat Conditions

Tuning electronic characteristics of metal-ligand bonds based on reaction pathways to achieve efficient catalytic processes has been widely studied and proven to be feasible in homogeneous catalysis, but it is scarcely investigated in heterogeneous catalysis. Herein, we demonstrate the regulation of the electronic configuration of Ir-O bonds in an Ir single-atom catalyst according to the borane activation mechanism. Ir-O bonds in Ir1/Ni(OH)x are found to be more electron-poor than those in Ir1/NiOx. Despite the mild solvent-free conditions and ambient temperature, Ir1/Ni(OH)x exhibits outstanding performance for the hydroboration of alkenes, furnishing the desired alkylboronic esters with a turnover frequency value of ≤3060 h-1 and 99% anti-Markovnikov selectivity, which is significantly better than that of Ir1/NiOx (42 h-1). It is further proven that the more electron-poor Ir-O bonds as active centers are more oxidative and so benefit the activation of the H-B bond in the reductive pinacolborane.

Strategies Toward High Selectivity, Activity, and Stability of Single-Atom Catalysts

Single-atom catalysts (SACs) hold immense promise in facilitating the rational use of metal resources and achieving atomic economy due to their exceptional atom-utilization efficiency and distinct characteristics. Despite the growing interest in SACs, only limited reviews have holistically summarized their advancements centering on performance metrics. In this review, first, a thorough overview on the research progress in SACs is presented from a performance perspective and the strategies, advancements, and intriguing approaches employed to enhance the critical attributes in SACs are discussed. Subsequently, a comprehensive summary and critical analysis of the electrochemical applications of SACs are provided, with a particular focus on their efficacy in the oxygen reduction reaction , oxygen evolution reaction, hydrogen evolution reaction , CO2 reduction reaction, and N2 reduction reaction . Finally, the outline future research directions on SACs by concentrating on performance-driven investigation, where potential areas for improvement are identified and promising avenues for further study are highlighted, addressing challenges to unlock the full potential of SACs as high-performance catalysts.

Integrated Ozonation Ni-NiO/Carbon/g-C3N4 Nanocomposite-Mediated Catalytic Decomposition of Organic Contaminants in Wastewater under Visible Light

Developing a hybrid process for wastewater purification is of utmost importance to make conventional methods more efficient and faster. Herein, an effective visible light-active nickel-nickel oxide/carbon/graphitic carbon nitride (Ni-NiO/C/g-C3N4)-based nanocatalyst was developed. A hybrid process based on ozonation and Ni-NiO/C/g-C3N4 visible light photocatalysis was applied to decolourize the Congo red (CR), Alizarin Red S (ARS), and real dairy industry wastewater. The synthesized catalyst was characterized using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), Χ-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectrophotometry (UV-Vis DRS). The factors affecting the catalytic process were evaluated, including contact time, solution pH, initial dye concentration, etc. The degradation rate of CR and ARS was compared between the photocatalysis, ozonation, and integrated photocatalytic ozonation (PC/O3) methods. The results showed 100% degradation of CR and ARS within 5 min and 40 min, respectively, by integrated PC/O3. The reusability of the modified catalyst was evaluated, and four successive regenerations were achieved. The modified Ni-NiO/C/g-C3N4 composite could be considered an effective, fast, and reusable catalyst in an integrated PC/O3 process for the complete decolourization of wastewater.

Multi-pathway on peroxymonosulfate activation by single cobalt atoms incorporated on CuO with enriched oxygen vacancies for high-efficient oxidation of tetracycline

The development of single atom catalysts (SACs) with superior catalytic performance is a long-term goal for peroxymonosulfate (PMS) activation in advanced oxidation processes (AOPs). A novel SACs that single Co atoms anchored on CuO with enriched oxygen vacancies (Ov) is synthesized successfully by choosing a metal oxide as the carrier creatively. 100% of tetracycline (TC) can be removed by Co-CuO (Ov)/PMS system within 3 min. The corresponding reaction rate constant is 3.1068 min-1, which is much higher than that of CuO (Ov), ZIF-CoN4-C, Co-CuO (without Ov) and CoNP-CuO (Ov), respectively. Co(II) is the primary source of radical pathway (·OH and SO4·-), and its regeneration is promoted by Cu(Ⅰ). The enriched Ov is the major contribution to the nonradical pathway, which promotes the singlet oxygen (1O2) generation together with accelerates the electron transfer from TC to catalyst-PMS*. Besides, the Co-CuO (Ov) exhibits an excellent stability and anti-interference capability. This study highlights a novel strategy to promote PMS activation by incorporating the single metal atoms on a metal oxide carrier with defects to accelerate the redox of dominate metal and stabilize the metal atoms simultaneously, which may inform the design for the next generation of SACs in AOPs.

Activating lattice oxygen in high-entropy LDH for robust and durable water oxidation

The oxygen evolution reaction is known to be a kinetic bottleneck for water splitting. Triggering the lattice oxygen oxidation mechanism (LOM) can break the theoretical limit of the conventional adsorbate evolution mechanism and enhance the oxygen evolution reaction kinetics, yet the unsatisfied stability remains a grand challenge. Here, we report a high-entropy MnFeCoNiCu layered double hydroxide decorated with Au single atoms and O vacancies (AuSA-MnFeCoNiCu LDH), which not only displays a low overpotential of 213 mV at 10 mA cm-2 and high mass activity of 732.925 A g-1 at 250 mV overpotential in 1.0 M KOH, but also delivers good stability with 700 h of continuous operation at ~100 mA cm-2. Combining the advanced spectroscopic techniques and density functional theory calculations, it is demonstrated that the synergistic interaction between the incorporated Au single atoms and O vacancies leads to an upshift in the O 2p band and weakens the metal-O bond, thus triggering the LOM, reducing the energy barrier, and boosting the intrinsic activity.

NiO Matrix Decorated by Ru Single Atoms: Electron-Rich Ru-Induced High Activity and Selectivity toward Electrochemical N2 Reduction

Developing a single-atom catalyst with electron-rich active sites is a promising strategy for catalyzing the electrochemical N₂ reduction reaction (NRR). Herein, we choose NiO(001) as a model template and deposit a series of single transition metal (TM) atoms with higher formal charges to create the electron-rich active centers. Our first-principles calculations show that low-valent Ru (+2) on NiO(001) can significantly activate N₂, with its oxidation states varying from +2 to +4 throughout the catalytic cycle. The Ru/NiO(001) catalyst exhibits the best activity with a relatively low limiting potential of -0.49 V. Furthermore, under NRR operating conditions, the Ru site is primarily occupied by *N₂ rather than *H, indicating that NRR overwhelms the hydrogen evolution reaction and thus exhibits excellent selectivity. Our work highlights the potential of designing catalysts with electron-rich active sites for NRR.

Competitive Trapping of Single Atoms onto a Metal Carbide Surface

Controlling atomic adjustment of single-atom catalysts (SACs) can directly change its local configuration, regulate the energy barrier of intermediates, and further optimize reaction pathways. Herein, we report an atom manipulating process to synthesize Ni atoms stabilized on vanadium carbide (Ni_SA-VC) through a nanofiber-medium thermodynamically driven atomic migration strategy. Experimental and theoretical results systematically reveal the tunable migration pathway of Ni atom from Ni nanoparticles to neighboring N-doped carbon (NC) and finally to metal carbide that was obtained by regulating the competitive adsorption energies between VC and NC for capturing Ni atoms. For CO₂-to-CO electroreduction, Ni_SA-VC exhibits an industrial current density of -180 mA cm^-2 at -1.0 V vs reversible hydrogen electrode and the highest Faradaic efficiency for CO production (FE_CO) of 96.8% at -0.4 V vs RHE in a flow cell. Significant electron transfers occurring in Ni_SA-VC structures contribute to the activation of CO₂, facilitate the reaction free energy, regulate *CO desorption as the rate-determining step, and promote the activity and selectivity. This study provides an understanding on how to design powerful SACs for electrocatalysis.

Recent advances in the theoretical studies on the electrocatalytic CO2 reduction based on single and double atoms

Excess of carbon dioxide (CO2) in the atmosphere poses a significant threat to the global climate. Therefore, the electrocatalytic carbon dioxide reduction reaction (CO2RR) is important to reduce the burden on the environment and provide possibilities for developing new energy sources. However, highly active and selective catalysts are needed to effectively catalyze product synthesis with high adhesion value. Single-atom catalysts (SACs) and double-atom catalysts (DACs) have attracted much attention in the field of electrocatalysis due to their high activity, strong selectivity, and high atomic utilization. This review summarized the research progress of electrocatalytic CO2RR related to different types of SACs and DACs. The emphasis was laid on the catalytic reaction mechanism of SACs and DACs using the theoretical calculation method. Furthermore, the influences of solvation and electrode potential were studied to simulate the real electrochemical environment to bridge the gap between experiments and computations. Finally, the current challenges and future development prospects were summarized and prospected for CO2RR to lay the foundation for the theoretical research of SACs and DACs in other aspects.

The adsorption of single Au atom and nucleation on γ-Al2O3 surfaces

Single-atom catalysts (SACs) in heterogeneous catalysts have attracted increasing attention and the adsorption and nucleation of single atom on the surface are closely related to the performance of the catalyst. The present work employed density functional theory calculations to examine the adsorption of single Au atom and nucleation on γ-Al₂O₃ surfaces at the atomic level. The effect of surface hydroxyls group on the adsorption and nucleation of single Au atom on γ-Al₂O₃ surfaces is explored. It was found that the spillover reactions of surface hydroxyls H atoms with the deposited Au_- are not available on the hydroxylated surface. The interaction of Au to the clean surface is the stronger than to the hydroxylated surface. The even-odd alternations of Au_x and weak binding of single Au atoms to γ-Al₂O₃ leads to large even-numbered Au cluster on the surface. Density of states and electron density difference analysis show that the electronic structure of Au/γ-Al₂O₃ is quite different from the reported Cu and Pd on Al₂O₃.

Coadsorption Interfered CO Oxidation over Atomically Dispersed Au on h-BN

Similar to the metal centers in biocatalysis and homogeneous catalysis, the metal species in single atom catalysts (SACs) are charged, atomically dispersed and stabilized by support and substrate. The reaction condition dependent catalytic performance of SACs has long been realized, but seldom investigated before. We investigated CO oxidation pathways over SACs in reaction conditions using atomically dispersed Au on h-BN (AuBN) as a model with extensive first-principles-based calculations. We demonstrated that the adsorption of reactants, namely CO, O₂ and CO₂, and their coadsorption with reaction species on AuBN would be condition dependent, leading to various reaction species with different reactivity and impact the CO conversion. Specifically, the revised Langmuir–Hinshelwood pathway with the CO-mediated activation of O₂ and dissociation of cyclic peroxide intermediate followed by the Eley–Rideal type reduction is dominant at high temperatures, while the coadsorbed CO-mediated dissociation of peroxide intermediate becomes plausible at low temperatures and high CO partial pressures. Carbonate species would also form in existence of CO₂, react with coadsorbed CO and benefit the conversion. The findings highlight the origin of the condition-dependent CO oxidation performance of SACs in detailed conditions and may help to rationalize the current understanding of the superior catalytic performance of SACs.