Defect Engineering in Solution-Processed Polycrystalline SnSe Leads to High Thermoelectric Performance

Enhanced Thermoelectric Performance of SnTe via Introducing Resonant Levels

SnTe has emerged as a non-toxic and environmentally friendly alternative to the high-performance thermoelectric material PbTe, attracting significant interest in sustainable energy applications. In our previous work, we successfully synthesized high-quality SnTe with reduced thermal conductivity under high-pressure conditions. Building on this, in this work, we introduced indium (In) doping to further decrease thermal conductivity under high pressure. By incorporating resonance doping into the SnTe matrix, we aimed to enhance the electrical transport properties while maintaining low thermal conductivity. This approach enhances the Seebeck coefficient to an impressive 153 μVK-1 at 735 K, marking a notable enhancement compared to undoped SnTe. Furthermore, we noted a substantial decrease in total thermal conductivity, dropping from 6.91 to 3.88 Wm-1K-1 at 325 K, primarily due to the reduction in electrical conductivity. The synergistic impact of decreased thermal conductivity and heightened Seebeck coefficient resulted in a notable improvement in the thermoelectric figure of merit (ZT) and average ZT, achieving approximately 0.5 and 0.22 in the doped samples, respectively. These advancements establish Sn1-xInxTe as a promising candidate to replace PbTe in thermoelectric applications, providing a safer and more environmentally sustainable option.

Enhanced thermoelectric performance of copper iodide particles/nanowires composite in the low-temperature range

Thermoelectric (TE) energy harvesting presents a viable method for reducing energy waste by transforming waste thermal energy into electricity. In this study, we fabricated copper iodide (CuI) composites using synthesized CuI nanowires (NWs) and particles to enhance TE performance in the low-temperature range. The Seebeck coefficient (S) was notably higher when a combination of CuI particles and NWs was used, reaching a maximum S of 1614.24 μV K-1 with a 60% NWs content at RT. Electrical conductivity (σ) exhibited an inverse correlation with S, with higher values detected when either particles or NWs were used only. The highest power factor (PF) of 128.44 μW m-1K-2 was recorded at RT with 60% NWs content, demonstrating improved TE performance. Thermal conductivity (κ) diminished when different material structures were employed, enhancing phonon scattering. The maximum figure of merit (ZT) achieved was ∼0.14 with 60% NWs content at 425 K, indicating the potential of this method for improving TE performance. This study offers valuable insights into optimizing TE performance using CuI composites, proposing a promising strategy for energy harvesting from low-temperature sources.

High Carrier Mobility and Promising Thermoelectric Module Performance of N-Type PbSe Crystals

The scarcity of Te hampers the widespread use of Bi2Te3-based thermoelectric modules. Here, the thermoelectric module potential of PbSe is investigated by improving its carrier mobility. Initially, large PbSe crystals are grown with the temperature gradient method to mitigate grain boundary effects on carrier transport. Subsequently, light doping with <1mole‰ halogens (Cl/Br/I) increases room-temperature carrier mobility to ~1600 cm2 V-1 s-1, achieved by reducing carrier concentration compared to traditional heavy doping. Crystal growth design and light doping enhance carrier mobility without affecting effective mass, resulting in a high power factor ~40 µW cm-1 K-2 in PbSe-Cl/Br/I crystals at 300 K. Additionally, Cl/Br/I doping reduces thermal conductivity and bipolar diffusion, leading to significantly lower thermal conductivity at high temperature. Enhanced carrier mobility and suppressed bipolar effect boost ZT values across the entire temperature range in n-type PbSe-Cl/Br/I crystals. Specifically, ZT values of PbSe-Br crystal reach ~0.6 at 300 K, ~1.2 at 773 K, and the average ZT (ZTave) reaches ~1.0 at 300-773 K. Ultimately, ~5.8% power generation efficiency in a PbSe single leg with a maximum temperature cooling difference of 40 K with 7-pair modules is achieved. These results indicate the potential for cost-effective and high-performance thermoelectric cooling modules based on PbSe.

Band Engineering Through Pb-Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Developing cost-effective and high-performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p-type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution-based approach is developed to synthesize high-quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6-fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4-based materials produced by solid-state, demonstrating advantages of versatility and cost-effectiveness using a solution-based technology.

Colloidal synthesis of two-dimensional nanocrystals by the polyol route

The field of 2D nanomaterials is ever-growing with a myriad of synthetic advancements that have been used to obtain such materials. There are top-down, as well as bottom-up, fabrication methods for obtaining 2D nanomaterials; however, synthesis of 2D nanomaterials from solution offers a simple scalable way to control size, shape, and surface. This review outlines the recent advances in colloidal polyol synthesis of 2D nanomaterials and provides perspectives on the similarities and differences in various syntheses. Various materials classes are presented and discussed, including metals, oxides, chalcogenides, and halides, that can be synthesized as 2D nanomaterials via a polyol process. Throughout the literature, polyol media is demonstrated to be versatile not only as a solvent and reducing agent for metal precursors but also as a binding and shape-directing agent for many 2D nanomaterials. Polyols also offer the ability to dissolve various surfactants and additives that can further control the morphology and composition of various nanomaterials. In this review, we outline the various 2D materials that have been realized via the solution polyol route.

Enhancing the Thermoelectric and Mechanical Properties of p-Type PbS through Band Convergence and Microstructure Regulation

While lead sulfide shows notable thermoelectric properties, its production costs remain high, and its mechanical hardness is low, which constrains its commercial viability. Herein, we demonstrate a straightforward and cost-effective method to produce PbS nanocrystals at ambient temperature. By introducing controlled amounts of silver, we achieve p-type conductivity and fine-tune the energy band structure and lattice configuration. Computational results show that silver shifts the Fermi level into the valence band, facilitating band convergence and thereby enhancing the power factor. Besides, excess silver is present as silver sulfide, which effectively diminishes the interface barrier and enhances the Seebeck coefficient. Defects caused by doping, along with dislocations and interfaces, reduce thermal conductivity to 0.49 W m-1 K-1 at 690 K. Moreover, the alterations in crystal structure and chemical composition enhance the PbS mechanical properties. Overall, optimized materials show thermoelectric figures of merit approximately 10-fold higher than that of pristine PbS, alongside an average hardness of 1.08 GPa.

Unveiling Crucial Chemical Processing Parameters Influencing the Performance of Solution-Processed Inorganic Thermoelectric Materials

Production of thermoelectric materials from solution-processed particles involves the synthesis of particles, their purification and densification into pelletized material. Chemical changes that occur during each one of these steps render them performance determining. Particularly the purification steps, bypassed in conventional solid-state synthesis, are the cause for large discrepancies among similar solution-processed materials. In present work, the investigation focuses on a water-based surfactant free solution synthesis of SnSe, a highly relevant thermoelectric material. We show and rationalize that the number of leaching steps, purification solvent, annealing, and annealing atmosphere have significant influence on the Sn : Se ratio and impurity content in the powder. Such compositional changes that are undetectable by conventional characterization techniques lead to distinct consolidated materials with different types and concentration of defects. Additionally, the profound effect on their transport properties is demonstrated. We emphasize that understanding the chemistry and identifying key chemical species and their role throughout the process is paramount for optimizing material performance. Furthermore, we aim to demonstrate the necessity of comprehensive reporting of these steps as a standard practice to ensure material reproducibility.

The Latest Advances in Ink-Based Nanogenerators: From Materials to Applications

Nanogenerators possess the capability to harvest faint energy from the environment. Among them, thermoelectric (TE), triboelectric, piezoelectric (PE), and moisture-enabled nanogenerators represent promising approaches to micro-nano energy collection. These nanogenerators have seen considerable progress in material optimization and structural design. Printing technology has facilitated the large-scale manufacturing of nanogenerators. Although inks can be compatible with most traditional functional materials, this inevitably leads to a decrease in the electrical performance of the materials, necessitating control over the rheological properties of the inks. Furthermore, printing technology offers increased structural design flexibility. This review provides a comprehensive framework for ink-based nanogenerators, encompassing ink material optimization and device structural design, including improvements in ink performance, control of rheological properties, and efficient energy harvesting structures. Additionally, it highlights ink-based nanogenerators that incorporate textile technology and hybrid energy technologies, reviewing their latest advancements in energy collection and self-powered sensing. The discussion also addresses the main challenges faced and future directions for development.

Cold Sintering Mediated Engineering of Polycrystalline SnSe with High Thermoelectric Efficiency

Despite the attractive thermoelectric properties in single crystals, the fabrication of high-performance polycrystalline SnSe by a cost-effective strategy remains challenging. In this study, we prepare the undoped SnSe ceramic with remarkable thermoelectric efficiency by the combination of a cold sintering process (CSP) and thermal annealing. The high sintering pressure during CSP induces not only highly oriented grains but also a high concentration of lattice dislocations and stacking faults, which leads to large lattice strain that can shorten the phonon relaxation time. Meanwhile, the thermal annealing breaks the highly resistive SnOx layers at grain boundaries, which improves the electrical conductivity and power factor. In addition, the grain growth during annealing further turns the broken SnOx layers into nanoparticles, which further lowers the thermal conductivity by enhanced scattering. As a result, a peak ZT of 1.3 at 890 K and a high average ZT of 0.69 are achieved in the polycrystalline SnSe, suggesting great potential in mid-temperature power generation. This work may pave the way for the mass production of SnSe-based ceramics for thermoelectric devices.

Green Synthesis and Morphological Evolution for Bi2Te3 Nanosystems via a PVP-Assisted Hydrothermal Method

Bi2Te3 has been extensively used because of its excellent thermoelectric properties at room temperature. Here, 230-420 nm of Bi2Te3 hexagonal nanosheets has been successfully synthesized via a "green" method by using ethylene glycol solution and applying polyvinyl pyrrolidone (PVP) as a surfactant. In addition, factors influencing morphological evolution are discussed in detail in this study. Among these parameters, the reaction temperature, molar mass of NaOH, different surfactants, and reaction duration are considered as the most essential. The results show that the existence of PVP is vital to the formation of a plate-like morphology. The reaction temperature and alkaline surroundings played essential roles in the formation of Bi2Te3 single crystals. By spark plasma sintering, the Bi2Te3 hexagonal nanosheets were hot pressed into solid-state samples. We also studied the transport properties of solid-state samples. The electrical conductivity σ was 18.5 × 103 Sm-1 to 28.69 × 103 Sm-1, and the Seebeck coefficient S was -90.4 to -113.3 µVK-1 over a temperature range of 300-550 K. In conclusion, the observation above could serve as a catalyst for future exploration into photocatalysis, solar cells, nonlinear optics, thermoelectric generators, and ultraviolet selective photodetectors of Bi2Te3 nanosheet-based photodetectors.

All-in-One Optoelectronic Logic Gates Enabled by Bipolar Spectral Photoresponse of CdTe/SnSe Heterojunction

Optoelectronic logic gate devices (OLGDs) have attracted significant attention in high-density information processors; however, multifunctional logic operation in a single device is technically challenging due to the unidirectional electrical transport. In this work, we deliberately design all-in-one OLGDs based on self-powered CdTe/SnSe heterojunction photodetectors. The SnSe nanorod (NR) array is grown on the sputtered CdTe film via a glancing-angle deposition technique to form a heterojunction device. At the interface, the photovoltaic (PV) effect in the CdTe/SnSe heterojunction and the photothermoelectric (PTE) effect from the SnSe NRs are combined together to induce the reversed photocurrent, leading to a unique bipolar spectral response. The competition between PV and PTE in different spectral ranges is thus employed to control the photocurrent polarity, and five basic logic gates of OR, AND, NAND, NOR, and NOT can be performed just with a single heterojunction. Our findings indicate the large potentials of the CdTe/SnSe heterojunctions as logic units in next-generation sensing-computing systems.

Design, synthesis, and application of some two-dimensional materials

Two-dimensional (2D) materials are widely used as key components in the fields of energy conversion and storage, optoelectronics, catalysis, biomedicine, etc. To meet the practical needs, molecular structure design and aggregation process optimization have been systematically carried out. The intrinsic correlation between preparation methods and the characteristic properties is investigated. This review summarizes the recent research achievements of 2D materials in the aspect of molecular structure modification, aggregation regulation, characteristic properties, and device applications. The design strategies to fabricate functional 2D materials starting from precursor molecules are introduced in detail referring to organic synthetic chemistry and self-assembly technology. It provides important research ideas for the design and synthesis of related materials.

Thermoelectric Performance of Surface-Engineered Cu1.5-xTe-Cu2Se Nanocomposites

Cu_2-xS and Cu_2-xSe have recently been reported as promising thermoelectric (TE) materials for medium-temperature applications. In contrast, Cu_2-xTe, another member of the copper chalcogenide family, typically exhibits low Seebeck coefficients that limit its potential to achieve a superior thermoelectric figure of merit, zT, particularly in the low-temperature range where this material could be effective. To address this, we investigated the TE performance of Cu_1.5-xTe-Cu₂Se nanocomposites by consolidating surface-engineered Cu_1.5Te nanocrystals. This surface engineering strategy allows for precise adjustment of Cu/Te ratios and results in a reversible phase transition at around 600 K in Cu_1.5-xTe-Cu₂Se nanocomposites, as systematically confirmed by in situ high-temperature X-ray diffraction combined with differential scanning calorimetry analysis. The phase transition leads to a conversion from metallic-like to semiconducting-like TE properties. Additionally, a layer of Cu₂Se generated around Cu_1.5-xTe nanoparticles effectively inhibits Cu_1.5-xTe grain growth, minimizing thermal conductivity and decreasing hole concentration. These properties indicate that copper telluride based compounds have a promising thermoelectric potential, translated into a high dimensionless zT of 1.3 at 560 K.

Electrical and Optical Properties of γ-SnSe: A New Ultra-narrow Band Gap Material

We describe the unusual properties of γ-SnSe, a new orthorhombic binary phase in the tin monoselenide system. This phase exhibits an ultranarrow band gap under standard pressure and temperature conditions, leading to high conductivity under ambient conditions. Density functional calculations identified the similarity and difference between the new γ-SnSe phase and the conventional α-SnSe based on the electron localization function. Very good agreement was obtained for the band gap width between the band structure calculations and the experiment, and insight provided for the mechanism of reduction in the band gap. The unique properties of this material may render it useful for applications such as thermal imaging devices and solar cells.

Large-Scale Colloidal Synthesis of Chalcogenides for Thermoelectric Applications

A simple and effective preparation of solution-processed chalcogenide thermoelectric materials is described. First, PbTe, PbSe, and SnSe were prepared by gram-scale colloidal synthesis relying on the reaction between metal acetates and diphenyl dichalcogenides in hexadecylamine solvent. The resultant phase-pure chalcogenides consist of highly crystalline and defect-free particles with distinct cubic-, tetrapod-, and rod-like morphologies. The powdered PbTe, PbSe, and SnSe products were subjected to densification by spark plasma sintering (SPS), affording dense pellets of the respective chalcogenides. Scanning electron microscopy shows that the SPS-derived pellets exhibit fine nano-/micro-structures dictated by the original morphology of the key constituting particles, while the powder X-ray diffraction and electron microscopy analyses confirm that the SPS-derived pellets are phase-pure materials, preserving the structure of the colloidal synthesis products. The resultant solution-processed PbTe, PbSe, and SnSe exhibit low thermal conductivity, which might be due to the enhanced phonon scattering developed over fine microstructures. For undoped n-type PbTe and p-type SnSe samples, an expected moderate thermoelectric performance is achieved. In contrast, an outstanding figure-of-merit of 0.73 at 673 K was achieved for undoped n-type PbSe outperforming, the majority of the optimized PbSe-based thermoelectric materials. Overall, our findings facilitate the design of efficient solution-processed chalcogenide thermoelectrics.

Insight into the intrinsic microstructures of polycrystalline SnSe based compounds

SnSe based compounds have attracted much attention due to the ultra-low lattice thermal conductivity and excellent thermoelectric properties. The origin of the low thermal conductivity has been ascribed to the strong phonon anharmonicity. Generally, the microstructures are also effective in scattering the phonons and further reducing the lattice thermal conductivity. In this work, the microstructures of undoped SnSe and Bi-doped Sn_0.97SeBi_0.03have been investigated by transmission electron microscopy. A characteristic microstructure of lath-like grains has been observed in SnSe based compounds from perpendicular to the pressure direction. In addition, there exist a large quantity of low-angle grain boundaries and a high concentration of edge dislocations and stacking faults in the grains. All these microstructures result in lattice mismatch and distortion and can act as the phonon scattering centers, which broaden the understanding of the low thermal conductivity of SnSe based compounds.

Enhanced Density of States Facilitates High Thermoelectric Performance in Solution-Grown Ge- and In-Codoped SnSe Nanoplates

SnSe single crystals have gained great interest due to their excellent thermoelectric performance. However, polycrystalline SnSe is greatly desired due to facile processing, machinability, and scale-up application. Here, we report an outstanding high average ZT of 0.88 as well as a high peak ZT of 1.92 in solution-processed SnSe nanoplates. Nanosized boundaries formed by nanoplates and lattice strain created by lattice dislocations and stacking faults effectively scatter heat-carrying phonons, resulting in an ultralow lattice thermal conductivity of 0.19 W m^-1 K^-1 at 873 K. Ultraviolet photoelectron spectroscopy reveals that Ge and In incorporation produces an enhanced density of states in the electronic structure of SnSe, resulting in a large Seebeck coefficient. Ge and In codoping not only optimizes the Seebeck coefficient but also substantially increases the carrier concentration and electrical conductivity, helping to maintain a high power factor over a wide temperature range. Benefiting from an enhanced power factor and markedly reduced lattice thermal conductivity, high average ZT and peak ZT are achieved in Ge- and In-codoped SnSe nanoplates. This work achieves an ultrahigh average ZT of 0.88 in polycrystalline SnSe by adopting nontoxic element doping, potentially expanding its usefulness for various thermoelectric generator applications.

Polymorphic Control of Solution-Processed Cu2SnS3 Films with Thiol-Amine Ink Formulation

There is increasing demand for tailored molecular inks that produce phase-pure solution-processed semiconductor films. Within the Cu-Sn-S phase space, Cu₂SnS₃ belongs to the I₂-IV-VI₃ class of semiconductors that crystallizes in several different polymorphs. We report the ability of thiol-amine solvent mixtures to dissolve inexpensive bulk Cu₂S and SnO precursors to generate free-flowing molecular inks. Upon mild annealing, polymorphic control over phase-pure tetragonal (I4̅2m) and orthorhombic (Cmc2₁) Cu₂SnS₃ films was realized simply by switching the identity of the thiol (i.e., 1,2-ethanedithiol vs 2-mercaptoethanol, respectively). Polymorph control is dictated by differences in the resulting molecular metal-thiolate complexes and their subsequent decomposition profiles, which likely seed distinct Cu_2-x S phases that template the ternary sulfide sublattice. The p-type tetragonal and orthorhombic Cu₂SnS₃ films possess similar experimental direct optical band gaps of 0.94 and 0.88 eV, respectively, and strong photoelectrochemical current responses. Understanding how ink formulation dictates polymorph choice should inform the development of other thiol-amine inks for solution-processed films.

Solution-Processed Inorganic Thermoelectric Materials: Opportunities and Challenges

Thermoelectric technology requires synthesizing complex materials where not only the crystal structure but also other structural features such as defects, grain size and orientation, and interfaces must be controlled. To date, conventional solid-state techniques are unable to provide this level of control. Herein, we present a synthetic approach in which dense inorganic thermoelectric materials are produced by the consolidation of well-defined nanoparticle powders. The idea is that controlling the characteristics of the powder allows the chemical transformations that take place during consolidation to be guided, ultimately yielding inorganic solids with targeted features. Different from conventional methods, syntheses in solution can produce particles with unprecedented control over their size, shape, crystal structure, composition, and surface chemistry. However, to date, most works have focused only on the low-cost benefits of this strategy. In this perspective, we first cover the opportunities that solution processing of the powder offers, emphasizing the potential structural features that can be controlled by precisely engineering the inorganic core of the particle, the surface, and the organization of the particles before consolidation. We then discuss the challenges of this synthetic approach and more practical matters related to solution processing. Finally, we suggest some good practices for adequate knowledge transfer and improving reproducibility among different laboratories.

Modular Nanostructures Facilitate Low Thermal Conductivity and Ultra-High Thermoelectric Performance in n-Type SnSe

Single crystals of SnSe have gained considerable attention in thermoelectrics due to their unprecedented thermoelectric performance. However, polycrystalline SnSe is more favorable for practical applications due to its facile chemical synthesis procedure, processability, and scalability. Though the thermoelectric figure of merit (zT) of p-type bulk SnSe polycrystals has reached >2.5, zT of n-type counterpart is still lower and lies around ≈1.5. Herein, record high zT of 2.0 in n-type polycrystalline SnSe_0.92  + x mol% MoCl₅ (x = 0-3) samples is reported, when measured parallel to the spark plasma sintering pressing direction due to the simultaneous optimization of n-type carrier concentration and enhanced phonon scattering by incorporating modular nano-heterostructures in SnSe matrix. Modular nanostructures of layered intergrowth [(SnSe)_1.05 ]_m (MoSe₂ )_n like compounds embedded in SnSe matrix scatters the phonons significantly leading to an ultra-low lattice thermal conductivity (κ_lat ) of ≈0.26 W m^-1 K^-1 at 798 K in SnSe_0.92  + 3 mol% MoCl₅ . The 2D layered modular intergrowth compound resembles the nano-heterostructure and their periodicity of 1.2-2.6 nm in the SnSe matrix matches the phonon mean free path of SnSe, thereby blocking the heat carrying phonons, which result in low κ_lat and ultra-high thermoelectric performance in n-type SnSe.

Phase-engineered high-entropy metastable FCC Cu2-y Ag y (In x Sn1-x )Se2S nanomaterials with high thermoelectric performance

Crystal-phase engineering to create metastable polymorphs is an effective and powerful way to modulate the physicochemical properties and functions of semiconductor materials, but it has been rarely explored in thermoelectrics due to concerns over thermal stability. Herein, we develop a combined colloidal synthesis and sintering route to prepare nanostructured solids through ligand retention. Nano-scale control over the unconventional cubic-phase is realized in a high-entropy Cu2-y Ag y (In x Sn1-x )Se2S (x = 0-0.25, y = 0, 0.07, 0.13) system by surface-ligand protection and size-driven phase stabilization. Different from the common monoclinic phase, the unconventional cubic-phase samples can optimize electrical and thermal properties through phase and entropy design. A high power factor (0.44 mW m-1 K-2), an ultralow thermal conductivity (0.25 W m-1 K-1) and a ZT value of 1.52 are achieved at 873 K for the cubic Cu1.87Ag0.13(In0.06Sn0.94)Se2S nanostructured sample. This study highlights a new method for the synthesis of metastable phase high-entropy materials and gives insights into stabilizing the metastable phase through ligand retention in other research communities.

Dramatic Enhancement of Thermoelectric Performance in PbTe by Unconventional Grain Shrinking in the Sintering Process

Nanostructure engineering is a key strategy for tailoring properties in the fields of batteries, solar cells, thermoelectrics, and so on. Limited by grain coarsening, however, the nanostructure effect gradually degrades during the materials' manufacturing and in-service period. Herein, a strategy of cleavage-fracture for grain shrinking is developed in a Pb_0.98 Sb_0.02 Te sample during sintering, and the grain size remains stable after repeated tests. Moreover, the initial grain boundary is filled by fractured slender grains and enriched by dislocations, evolving into a hierarchical grain-boundary structure. The lattice thermal conductivity (k_lat ) is greatly reduced to approach the amorphous limit. As a result, a record-high ZT value of ≈1.9 is obtained at 815 K in the n-type Pb_0.98 Sb_0.02 Te sample and a decent efficiency of 6.7% in thermoelectric device. This strategy for grain shrinking will shed light on the application of nanostructure engineering under high temperature and extreme conditions in other material systems.

Surface Functionalization of Surfactant-Free Particles: A Strategy to Tailor the Properties of Nanocomposites for Enhanced Thermoelectric Performance

The broad implementation of thermoelectricity requires high-performance and low-cost materials. One possibility is employing surfactant-free solution synthesis to produce nanopowders. We propose the strategy of functionalizing "naked" particles' surface by inorganic molecules to control the nanostructure and, consequently, thermoelectric performance. In particular, we use bismuth thiolates to functionalize surfactant-free SnTe particles' surfaces. Upon thermal processing, bismuth thiolates decomposition renders SnTe-Bi2 S3 nanocomposites with synergistic functions: 1) carrier concentration optimization by Bi doping; 2) Seebeck coefficient enhancement and bipolar effect suppression by energy filtering; and 3) lattice thermal conductivity reduction by small grain domains, grain boundaries and nanostructuration. Overall, the SnTe-Bi2 S3 nanocomposites exhibit peak z T up to 1.3 at 873 K and an average z T of ≈0.6 at 300-873 K, which is among the highest reported for solution-processed SnTe.

Surface Functionalization of Surfactant-Free Particles: A Strategy to Tailor the Properties of Nanocomposites for Enhanced Thermoelectric Performance

The broad implementation of thermoelectricity requires high-performance and low-cost materials. One possibility is employing surfactant-free solution synthesis to produce nanopowders. We propose the strategy of functionalizing "naked" particles' surface by inorganic molecules to control the nanostructure and, consequently, thermoelectric performance. In particular, we use bismuth thiolates to functionalize surfactant-free SnTe particles' surfaces. Upon thermal processing, bismuth thiolates decomposition renders SnTe-Bi2S3 nanocomposites with synergistic functions: 1) carrier concentration optimization by Bi doping; 2) Seebeck coefficient enhancement and bipolar effect suppression by energy filtering; and 3) lattice thermal conductivity reduction by small grain domains, grain boundaries and nanostructuration. Overall, the SnTe-Bi2S3 nanocomposites exhibit peak z  T up to 1.3 at 873 K and an average z  T of ≈0.6 at 300-873 K, which is among the highest reported for solution-processed SnTe.

Insights into Low Thermal Conductivity in Inorganic Materials for Thermoelectrics

Efficient manipulation of thermal conductivity and fundamental understanding of the microscopic mechanisms of phonon scattering in crystalline solids are crucial to achieve high thermoelectric performance. Thermoelectric energy conversion directly and reversibly converts between heat and electricity and is a promising renewable technology to generate electricity by recovering waste heat and improve solid-state refrigeration. However, a unique challenge in thermal transport needs to be addressed to achieve high thermoelectric performance: the requirement of crystalline materials with ultralow lattice thermal conductivity (κ_L). A plethora of strategies have been developed to lower κ_L in crystalline solids by means of nanostructural modifications, introduction of intrinsic or extrinsic phonon scattering centers with tailored shape and dimension, and manipulation of defects and disorder. Recently, intrinsic local lattice distortion and lattice anharmonicity originating from various mechanisms such as rattling, bonding heterogeneity, and ferroelectric instability have found popularity. In this Perspective, we outline the role of manipulation of chemical bonding and structural chemistry on thermal transport in various high-performance thermoelectric materials. We first briefly outline the fundamental aspects of κ_L and discuss the current status of the popular phonon scattering mechanisms in brief. Then we discuss emerging new ideas with examples of crystal structure and lattice dynamics in exemplary materials. Finally, we present an outlook for focus areas of experimental and theoretical challenges, possible new directions, and integrations of novel techniques to achieve low κ_L in order to realize high-performance thermoelectric materials.

Enhancement of the Thermoelectric Performance of Cu2GeSe3 via Isoelectronic (Ag, S)-co-substitution

Recently, ternary Cu-based Cu-IV-Se (IV = Sb, Ge, and Sn) compounds have received extensive attention in the thermoelectric field. Compared with Cu-Sb-Se and Cu-Sn-Se, Cu-Ge-Se compounds have been less studied due to its poor Seebeck coefficient and high thermal conductivity. Here, the Cu₂GeSe₃ material with high electrical conductivity was first prepared, and then, its effective mass was increased by doping with S, which led to the Seebeck coefficient of the doped sample being 1.93 times higher than that of pristine Cu₂GeSe₃ at room temperature. Moreover, alloying Ag at the Cu site in the Cu₂GeSe_2.96S_0.04 sample could further cause a 5.16 times increase in the Seebeck coefficient at room temperature, and the lattice thermal conductivity was remarkably decreased because of the introduction of the dislocations in the Cu₂GeSe₃ sample. Finally, benefitted from the high Seebeck coefficient and low thermal conductivity, a record high ZT = 0.9 at 723 K was obtained for the Cu_1.85Ag_0.15GeSe_2.96S_0.04 sample, which increased 345% in comparison with the pristine Cu₂GeSe₃, and it is among the highest reported values for Cu₂GeSe₃-based thermoelectric.

Pressure-driven thermoelectric properties of defect chalcopyrite structured ZnGa2Te4: ab initio study

The pressure induced structural, electronic, transport, and lattice dynamical properties of ZnGa2Te4 were investigated with the combination of density functional theory, Boltzmann transport theory and a modified Debye-Callaway model. The structural transition from I4̄ to I4̄2m occurs at 12.09 GPa. From the basic observations, ZnGa2Te4 is found to be mechanically as well as thermodynamically stable and ductile up to 12 GPa. The direct band gap of 1.01 eV is inferred from the electronic band structure. The quantitative analysis of electron transport properties shows that ZnGa2Te4 has moderate Seebeck coefficient and electrical conductivity under high pressure, which resulted in a large power factor of 0.63 mW m-1 K-2 (750 K). The ultralow lattice thermal conductivity (∼1 W m-1 K-1 at 12 GPa) is attributed to the overlapping of acoustic and optical phonon branches. As a result, the optimal figure of merit of 0.77 (750 K) is achieved by applying a pressure of 12 GPa. These findings support that ZnGa2Te4 can be a potential p-type thermoelectric material under high pressure and thus open the door for its experimental exploration.

Kinetics and mechanistic details of bulk ZnO dissolution using a thiol-imidazole system

Oxide dissolution is important for metal extraction from ores and has become an attractive route for the preparation of inks for thin film solution deposition; however, oxide dissolution is often kinetically challenging. While binary "alkahest" systems comprised of thiols and N-donor species, such as amines, are known to dissolve a wide range of oxides, the mechanism of dissolution and identity of the resulting solute(s) remain unstudied. Here, we demonstrate facile dissolution of both bulk synthetic and natural mineral ZnO samples using an "alkahest" that operates via reaction with thiophenol and 1-methylimidazole (MeIm) to give a single, pseudotetrahedral Zn(SPh)2(MeIm)2 molecular solute identified by X-ray crystallography. The kinetics of ZnO dissolution were measured using solution 1H NMR, and the reaction was found to be zero-order in the presence of excess ligands, with more electron withdrawing para-substituted thiophenols resulting in faster dissolution. A negative entropy of activation was measured by Eyring analysis, indicating associative ligand binding in, or prior to, the rate determining step. Combined experimental and computational surface binding studies on ZnO reveal stronger, irreversible thiophenol binding compared to MeIm, leading to a proposed dissolution mechanism initiated by thiol binding to the ZnO surface with the liberation of water, followed by alternating MeIm and thiolate ligand additions, and ultimately cleavage of the ligated zinc complex from the ZnO surface. Design rules garnered from the mechanistic insight provided by this study should inform the dissolution of other bulk oxides into inks for solution processed thin films.

High-Performance Thermoelectrics Based on Solution-Grown SnSe Nanostructures

Two-dimensional layered tin selenide (SnSe) has attracted immense interest in thermoelectrics due to its ultralow lattice thermal conductivity and high thermoelectric performance. To date, the majority of thermoelectric studies of SnSe have been based on single crystals. However, because synthesizing SnSe single crystals is an expensive, time-consuming process that requires high temperatures and because SnSe single crystals have relatively weaker mechanical stability, they are not favorable for scaling up synthesis, commercialization, or practical applications. As a result, research on nanocrystalline SnSe that can be produced in large quantities by simple and low-temperature solution-phase synthesis is needed. In this Perspective, we discuss the progress in thermoelectric properties of SnSe with a particular emphasis on nanocrystalline SnSe, which is grown in solution. We first describe the state-of-the-art high-performance single crystal and polycrystals of SnSe and their importance and drawbacks and discuss how nanocrystalline SnSe can solve some of these challenges. We illustrate different solution-phase synthesis procedures to produce various SnSe nanostructures and discuss their thermoelectric properties. We also highlight a unique solution-phase synthesis technique to prepare CdSe-coated SnSe nanocomposites and its unprecedented thermoelectric figure of merit (ZT) of 2.2 at 786 K, as reported in this issue of ACS Nano. In general, solution synthesis showed excellent control over nanoscale grain growth, and nanocrystalline SnSe shows ultralow thermal conductivity due to strong phonon scattering by the nanoscale grain boundaries. Finally, we offer insight into the opportunities and challenges associated with nanocrystalline SnSe synthesized by the solution route and its future in thermoelectric energy conversion.

An Overview of the Strategies for Tin Selenide Advancement in Thermoelectric Application

Chalcogenide, tin selenide-based thermoelectric (TE) materials are Earth-abundant, non-toxic, and are proven to be highly stable intrinsically with ultralow thermal conductivity. This work presented an updated review regarding the extraordinary performance of tin selenide in TE applications, focusing on the crystal structures and their commonly used fabrication methods. Besides, various optimization strategies were recorded to improve the performance of tin selenide as a mid-temperature TE material. The analyses and reviews over the methodologies showed a noticeable improvement in the electrical conductivity and Seebeck coefficient, with a noticeable decrement in the thermal conductivity, thereby enhancing the tin selenide figure of merit value. The applications of SnSe in the TE fields such as microgenerators, and flexible and wearable devices are also discussed. In the future, research in low-dimensional TE materials focusing on nanostructures and nanocomposites can be conducted with the advancements in material science technology as well as microtechnology and nanotechnology.

PbS-Pb-CuxS Composites for Thermoelectric Application

Composite materials offer numerous advantages in a wide range of applications, including thermoelectrics. Here, semiconductor-metal composites are produced by just blending nanoparticles of a sulfide semiconductor obtained in aqueous solution and at room temperature with a metallic Cu powder. The obtained blend is annealed in a reducing atmosphere and afterward consolidated into dense polycrystalline pellets through spark plasma sintering (SPS). We observe that, during the annealing process, the presence of metallic copper activates a partial reduction of the PbS, resulting in the formation of PbS-Pb-Cu_xS composites. The presence of metallic lead during the SPS process habilitates the liquid-phase sintering of the composite. Besides, by comparing the transport properties of PbS, the PbS-Pb-Cu_xS composites, and PbS-Cu_xS composites obtained by blending PbS and Cu_xS nanoparticles, we demonstrate that the presence of metallic lead decisively contributes to a strong increase of the charge carrier concentration through spillover of charge carriers enabled by the low work function of lead. The increase in charge carrier concentration translates into much higher electrical conductivities and moderately lower Seebeck coefficients. These properties translate into power factors up to 2.1 mW m^-1 K^-2 at ambient temperature, well above those of PbS and PbS + Cu_xS. Additionally, the presence of multiple phases in the final composite results in a notable decrease in the lattice thermal conductivity. Overall, the introduction of metallic copper in the initial blend results in a significant improvement of the thermoelectric performance of PbS, reaching a dimensionless thermoelectric figure of merit ZT = 1.1 at 750 K, which represents about a 400% increase over bare PbS. Besides, an average ZT_ave = 0.72 in the temperature range 320-773 K is demonstrated.