Large-Area Ultrastrong and Stiff Layered MXene Nanocomposites by Shear-Flow-Induced Alignment of Nanosheets

Ultrafine Aramid Nanofiber-Assisted Large-Area Dense Stacking of MXene Films for Electromagnetic Interference Shielding and Multisource Thermal Conversion

Polymers are often used as adhesives to improve the mechanical properties of flexible electromagnetic interference (EMI) shielding layered films, but the introduction of these insulating adhesives inevitably reduces the EMI performance. Herein, ultrafine aramid nanofibers (UANF) with a diameter of only 2.44 nm were used as the binder to effectively infiltrate and minimize the insulating gaps in MXene films, for balancing the EMI shielding and mechanical properties. Combining the evaporation-induced scalable assembly assisted by blade coating, flexible large-scale MXene/UANF films with highly aligned and compact MXene stacking are successfully fabricated. Compared with the conventional ANF with a larger diameter of 7.05 nm, the UANF-reinforced MXene film exhibits a "brick-mortar" structure with higher orientation and compacter stacking MXene nanosheets, thus showing the higher mechanical properties, electrical conductivity, and EMI shielding performance. By optimizing MXene content, the MXene/UANF film can achieve the optimal tensile strength of 156.9 MPa, a toughness of 2.9 MJ m-3, satisfactory EMI shielding effectiveness (EMI SE) of 40.7 dB, and specific EMI SE (SSE/t) of 22782.4 dB cm2/g). Moreover, the composite film exhibits multisource thermal conversion functions including Joule heating and photothermal conversion. Therefore, the multifunctional MXene/UANF EMI shielding film with flexibility, foldability, and robust mechanical properties shows the practical potential in complex application environments.

Superspreading-Based Fabrication of Thermostable Nanoporous Polyimide Membranes for High Safety Separators of Lithium-Ion Batteries

The development of thermally stable separators is a promising approach to address the safety issues of lithium-ion batteries (LIBs) owing to the serious shrinkage of commercial polyolefin separators at elevated temperatures. However, achieving controlled nanopores with a uniform size distribution in thermostable polymeric separators and high electrochemical performance is still a great challenge. In this study, nanoporous polyimide (PI) membranes with excellent thermal stability as high-safety separators is developed for LIBs using a superspreading strategy. The superspreading of polyamic acid solutions enables the generation of thin and uniform liquid layers, facilitating the formation of thin PI membranes with controllable and uniform nanopores with narrow size distribution ranging from 121 ± 5 nm to 86 ± 6 nm. Such nanoporous PI membranes display excellent structural stability at elevated temperatures up to 300 °C for at least 1 h. LIBs assembled with nanoporous PI membranes as separators show high specific capacity and Coulombic efficiency and can work normally after transient treatment at a high temperature (150 °C for 20 min) and high ambient temperature, indicating their promising application as high-safety separators for rechargeable batteries.

Guidelines derived from biomineralized tissues for design and construction of high-performance biomimetic materials: from weak to strong

Living organisms in nature have undergone continuous evolution over billions of years, resulting in the formation of high-performance fracture-resistant biomineralized tissues such as bones and teeth to fulfill mechanical and biological functions, despite the fact that most inorganic biominerals that constitute biomineralized tissues are weak and brittle. During the long-period evolution process, nature has evolved a number of highly effective and smart strategies to design chemical compositions and structures of biomineralized tissues to enable superior properties and to adapt to surrounding environments. Most biomineralized tissues have hierarchically ordered structures consisting of very small building blocks on the nanometer scale (nanoparticles, nanofibers or nanoflakes) to reduce the inherent weaknesses and brittleness of corresponding inorganic biominerals, to prevent crack initiation and propagation, and to allow high defect tolerance. The bioinspired principles derived from biomineralized tissues are indispensable for designing and constructing high-performance biomimetic materials. In recent years, a large number of high-performance biomimetic materials have been prepared based on these bioinspired principles with a large volume of literature covering this topic. Therefore, a timely and comprehensive review on this hot topic is highly important and contributes to the future development of this rapidly evolving research field. This review article aims to be comprehensive, authoritative, and critical with wide general interest to the science community, summarizing recent advances in revealing the formation processes, composition, and structures of biomineralized tissues, providing in-depth insights into guidelines derived from biomineralized tissues for the design and construction of high-performance biomimetic materials, and discussing recent progress, current research trends, key problems, future main research directions and challenges, and future perspectives in this exciting and rapidly evolving research field.

Porifera-Inspired Lightweight, Thin, Wrinkle-Resistance, and Multifunctional MXene Foam

Transition metal carbides/nitrides (MXenes) demonstrate a massive potential in constructing lightweight, multifunctional wearable electromagnetic interference (EMI) shields for application in various fields. Nevertheless, it remains challenging to develop a facile, scalable approach to prepare the MXene-based macrostructures characterized by low density, low thickness, high mechanical flexibility, and high EMI SE at the same time. Herein, the ultrathin MXene/reduced graphene oxide (rGO)/Ag foams with a porifera-inspired hierarchically porous microstructure are prepared by combining Zn2+ diffusion induction and hard template methods. The hierarchical porosity, which includes a mesoporous skeleton and a microporous MXene network within the skeleton, not only exerts a regulatory effect on stress distribution during compression, making the foams rubber-like resistant to wrinkling but also provides more channels for multiple reflections of electromagnetic waves. Due to the interaction between Ag nanosheets, MXene/rGO, and porous structure, it is possible to produce an outstanding EMI shielding performance with the specific surface shielding effectiveness reaching 109152.4 dB cm2 g-1. Furthermore, the foams exhibit multifunctionalities, such as transverse Joule heating, longitudinal heat insulation, self-cleaning, fire resistance, and motion detection. These discoveries open up a novel pathway for the development of lightweight MXene-based materials with considerable application potential in wearable electromagnetic anti-interference devices.

Bioinspired Dielectric Nanocomposites with High Charge-Discharge Efficiency Enabled by Superspreading-Induced Alignment of Nanosheets

High-performance dielectric nanocomposites are promising candidates for thin-film dielectric capacitors for high-power pulse devices. However, the existing nanocomposites suffer from low charge-discharge efficiency (η), which results in severe generation and accumulation of Joule heat and subsequently the failure of the devices. In this work, we report nacre-inspired dielectric nanocomposites with outstanding η, which are enabled by superspreading shear flow-induced highly aligned two-dimensional (2D) nanofillers. Taking boron nitride nanosheets (BNNS) as an example, the highly aligned BNNS in the poly(vinylidene fluoride) (PVDF)-based nanocomposites contributes to a highly efficient Coulomb blockade effect for the injected charge carriers. Therefore, the bioinspired nanocomposites with highly aligned BNNS show significantly reduced dielectric loss (tan δ) (63.3%) and improved η (144.8%), compared to the ones with partially aligned nanosheets fabricated by solution casting. Furthermore, the optimized loading content of BNNS is as low as 3.6 wt %. The resulting nanocomposites exhibit reduced tan δ (0.018) and enhanced Eb (687 kV/mm), η (71%), and Ue (16.74 J/cm3). Our work demonstrates that the realization of high alignment of 2D nanofillers enabled by the superspreading shear flow is a promising way for the development of high-performance dielectric nanocomposites.

Bioinspired 2D nanofluidic membranes for energy applications

Bioinspired two-dimensional (2D) nanofluidic membranes have been explored for the creation of high-performance ion transport systems that can mimic the delicate transport functions of living organisms. Advanced energy devices made from these membranes show excellent energy storage and conversion capabilities. Further research and development in this area are essential to unlock the full potential of energy devices and facilitate the development of high-performance equipment toward real-world applications and a sustainable future. However, there has been minimal review and summarization of 2D nanofluidic membranes in recent years. Thus, it is necessary to carry out an extensive review to provide a survey library for researchers in related fields. In this review, the classification and the raw materials that are used to construct 2D nanofluidic membranes are first presented. Second, the top-down and bottom-up methods for constructing 2D membranes are introduced. Next, the applications of bioinspired 2D membranes in osmotic energy, hydraulic energy, mechanical energy, photoelectric conversion, lithium batteries, and flow batteries are discussed in detail. Finally, the opportunities and challenges that 2D nanofluidic membranes are likely to face in the future are envisioned. This review aims to provide a broad knowledge base for constructing high-performance bioinspired 2D nanofluidic membranes for advanced energy applications.

Bottom-Up Film-to-Bulk Assembly Toward Bioinspired Bulk Structural Nanocomposites

Biological materials, although composed of meager minerals and biopolymers, often exhibit amazing mechanical properties far beyond their components due to hierarchically ordered structures. Understanding their structure-properties relationships and replicating them into artificial materials would boost the development of bulk structural nanocomposites. Layered microstructure widely exists in biological materials, serving as the fundamental structure in nanosheet-based nacres and nanofiber-based Bouligand tissues, and implying superior mechanical properties. High-efficient and scalable fabrication of bioinspired bulk structural nanocomposites with precise layered microstructure is therefore important yet remains difficult. Here, one straightforward bottom-up film-to-bulk assembly strategy is focused for fabricating bioinspired layered bulk structural nanocomposites. The bottom-up assembly strategy inherently offers a methodology for precise construction of bioinspired layered microstructure in bulk form, availability for fabrication of bioinspired bulk structural nanocomposites with large sizes and complex shapes, possibility for design of multiscale interfaces, feasibility for manipulation of diverse heterogeneities. Not limited to discussing what has been achieved by using the current bottom-up film-to-bulk assembly strategy, it is also envisioned how to promote such an assembly strategy to better benefit the development of bioinspired bulk structural nanocomposites. Compared to other assembly strategies, the highlighted strategy provides great opportunities for creating bioinspired bulk structural nanocomposites on demand.

Affine Deformation and Self-Assembly Alignment in Hydrogel Nanocomposites

Tailoring the order in hierarchical structures is a key goal of bioinspired nanocomposite design. Recently, nacre-like materials have been developed by solvent evaporation methods that are scalable and attain advanced functionalities. However, understanding the alignment mechanisms of 2D fillers, nanosheets, or platelets remains challenging. This work explores possible pathways for nanocomposite ordering via orientation distribution functions. We demonstrate how the immobilization of 2D materials via (pseudo)network formation is crucial to alignment based on evaporation. We show a modified affine deformation model that describes such evaporative methods. In this, a gel network develops enough yield stress and uniformly deforms as drying proceeds, along with the immobilized particles, causing an in-plane orientation. Herein, we tested the dominance of this approach by using a thermo-reversible gel for rapid montmorillonite (MMT) particle fixation. We researched gelatin/MMT as a model system to investigate the effects of high loadings, orientational order, and aspect ratio. The nacre-like nanocomposites showed a semiconstant order parameter (⟨P2⟩ ∼ 0.7) over increasing nanofiller content up to 64 vol % filler. This remarkable alignment resulted in continuously improved mechanical and water vapor barrier properties over unusually large filler fractions. Some variations in stiffness and diffusion properties were observed, possibly correlated to the applied drying conditions of the hybrid hydrogels. The affine deformation strategy holds promise for developing next-generation advanced materials with tailored properties even at (very) high filler loadings. Furthermore, a gelling approach offers the advantages of simplicity and versatility in the formulation of the components, which is useful for large-scale fabrication methods.

High strength, self-healing sensitive ionogel sensor based on MXene/ionic liquid synergistic conductive network for human-motion detection

Ionogels with both high strength and high conductivity for wearable strain and pressure dual-mode sensors are needed for human motion and health monitoring. Here, multiple hydrogen bonds are introduced through imidazolidinyl urea (IU) as a chain extender to provide high mechanical and self-healing properties for the water-borne polyurethane (WPU). The MXene/ionic liquids synergistic conductive network provides excellent conductivity and also reduces the relative content of ionic liquids to maintain the mechanical properties of the ionogels. The mechanical strength of this ionogel reached 1.81-2.24 MPa and elongation at break reached 570-624%. It also has excellent conductivity (22.7-37.5 mS m-1), gauge factor (GF) (as a strain sensor, GF = 1.8), sensitivity (S) (as a press sensor, S1 = 29.8 kPa-1, S2 = 1.3 kPa-1), and fast response time (as a strain sensor = 185 ms; as a press sensor = 204 ms). The ionogel also exhibits rapid photothermal self-healing capabilities due to the inherent photothermal behavior of MXene. It can maintain good elasticity and conductivity at low temperatures. In addition, this ionogel is able to stretch for 1200 cycles without significant change in the relative change of resistance. The ionogel can be assembled as a strain sensor for monitoring human motion and as a pressure sensor array for obtaining pressure magnitude and position information.

Residual Strain and Nanostructural Effects during Drying of Nanocellulose/Clay Nanosheet Hybrids: Synchrotron X-ray Scattering Results

Cellulose nanofibrils (CNF) with 2D silicate nanoplatelet reinforcement readily form multifunctional composites by vacuum-assisted self-assembly from hydrocolloidal mixtures. The final nanostructure is formed during drying. The crystalline nature of CNF and montmorillonite (MTM) made it possible to use synchrotron X-ray scattering (WAXS, SAXS) to monitor structural development during drying from water and from ethanol. Nanostructural changes in the CNF and MTM crystals were investigated. Changes in the out-of-plane orientation of CNF and MTM were determined. Residual drying strains previously predicted from theory were confirmed in both cellulose and MTM platelets due to capillary forces. The formation of tactoid platelet stacks could be followed. We propose that after filtration, the constituent nanoparticles in the swollen, solid gel already have a "fixed" location, although self-assembly and ordering processes take place during drying.

Applications of X-Ray-Based Characterization in MXene Research

X-rays are a penetrating form of high-energy electromagnetic radiation with wavelengths ranging from 10 pm to 10 nm. Similar to visible light, X-rays provide a powerful tool to study the atoms and elemental information of objects. Different characterization methods based on X-rays are established, such as X-ray diffraction, small- and wide-angle X-ray scattering, and X-ray-based spectroscopies, to explore the structural and elemental information of varied materials including low-dimensional nanomaterials. This review summarizes the recent progress of using X-ray related characterization methods in MXenes, a new family of 2D nanomaterials. These methods provide key information on the nanomaterials, covering synthesis, elemental composition, and the assembly of MXene sheets and their composites. Additionally, new characterization methods are proposed as future research directions in the outlook section to enhance understanding of MXene surface and chemical properties. This review is expected to provide a guideline for characterization method selection and aid in precise interpretation of the experimental data in MXene research.

Structural design and preparation of Ti3C2Tx MXene/polymer composites for absorption-dominated electromagnetic interference shielding

Electromagnetic interference (EMI) is a pervasive and harmful phenomenon in modern society that affects the functionality and reliability of electronic devices and poses a threat to human health. To address this issue, EMI-shielding materials with high absorption performance have attracted considerable attention. Among various candidates, two-dimensional MXenes are promising materials for EMI shielding due to their high conductivity and tunable surface chemistry. Moreover, by incorporating magnetic and conductive fillers into MXene/polymer composites, the EMI shielding performance can be further improved through structural design and impedance matching. Herein, we provide a comprehensive review of the recent progress in MXene/polymer composites for absorption-dominated EMI shielding applications. We summarize the fabrication methods and EMI shielding mechanisms of different composite structures, such as homogeneous, multilayer, segregated, porous, and hybrid structures. We also analyze the advantages and disadvantages of these structures in terms of EMI shielding effectiveness and the absorption ratio. Furthermore, we discuss the roles of magnetic and conductive fillers in modulating the electrical properties and EMI shielding performance of the composites. We also introduce the methods for evaluating the EMI shielding performance of the materials and emphasize the electromagnetic parameters and challenges. Finally, we provide insights and suggestions for the future development of MXene/polymer composites for EMI shielding applications.