Adsorption of Methyl Orange from an Aqueous Solution onto a BPPO-Based Anion Exchange Membrane

Recent advancements in the synthesis of anion exchange membranes and their potential applications in wastewater treatment

Water treatment procedures are increasingly utilized for resource recovery and wastewater disinfection, addressing the current challenges of clean water depletion and wastewater management. Various pollutants, including dyes, acids, pharmaceuticals, and toxic heavy metals have been released into the environment through industrial, domestic, and agricultural activities, posing serious environmental and public health risks. Addressing these issues requires the development of more effective waste treatment processes. Membrane-based treatment technologies offer significant advantages, including high efficiency, versatility, and cost-effectiveness, making them a promising solution for mitigating the impact of these pollutants. In view of this, the potential of ion exchange membranes (IEMs) is continuously increasing due to their advanced characteristics compared to conventional techniques. Anion exchange membranes (AEMs), a special class of IEMs, selectively allow anions to pass through their pores due to the positive charge on their surface. This selective passage aids in resource recovery and removing specific types of pollutants. This review covers preparation methods, modification techniques, and classification of AEMs. It offers a practical classification based on the method of synthesis and structural properties of AEMs. The water-based applications of AEMs including, electrodialysis, diffusion dialysis, and electro-electrodialysis for various wastewater treatments such as heavy metal recovery, dye removal, pharmaceutical removal, and acid separation, have been discussed in detail. Additionally, the effect of various operational parameters on the performance and SWOT (strengths, weaknesses, opportunities, and threats) analysis of AEMs in effluent treatment are presented. The review provides detailed insights into the current status, challenges, and future directions of AEM-based technologies, offering suggestions for future advancements.

Bimetal Cu/Ni-BTC@SiO2 metal-organic framework as high performance photocatalyst for degradation of azo dyes under visible light irradiation

There has been significant attention on the efficient degradation of pollutants in wastewater using metal-organic frameworks (MOFs) photocatalytic methods over the past decade. Herein, we examined the elimination of two different types of water-contaminating dyes, specifically cationic dye methylene blue (MB) and anionic dye methyl orange (MO), through the application of bimetal Cu/Ni-BTC@SiO2 MOF as high performance photocatalyst. The bimetal Cu/Ni-BTC@SiO2 photocatalyst was synthesized and characterized by XRD, FTIR, SEM, TEM, TGA, BET, DRS, and VSM techniques. The examination of the impact of different operational factors on the elimination of pollutants involved a comprehensive analysis of variables including the photocatalyst type, initial pollutant concentration, quantity of photocatalyst, and pH levels. The highest removal efficiency for MO and MB dyes by the photocatalyst was found to be 98 and 71%, respectively, within 60 min. In the fifth reaction stage, degradation efficiency for MO and MB was 76 and 56% respectively. Kinetic investigations demonstrated that, in the context of the uptake of MB and MO dyes, the interparticle diffusion, and pseudo-second-order models emerged as possessing the most robust correlation coefficients with the experimental data, registering values of 0.988 and 0.961, respectively. The examination of isotherms reveals that the isotherm models proposed by BET, and Anderson (V) demonstrate the highest level of conformity with the empirical data for the decomposition of MB and MO dyes, correspondingly. The TOC levels decreased significantly from 51 to 14 and 47 to 3 mg/L for MB and MO dyes, indicating the effective mineralization process using Cu/Ni-BTC@SiO2.

Neem biomass derived carbon quantum dots synthesized via one step ultrasonification method for ecofriendly methylene blue dye removal

This article presents a one-step ultrasonication technique for generating biomass carbon dots (BCDs) from neem bark (Azadirachta indica) powder. The BCDs were characterized using modern techniques such as UV-Vis, FTIR, Raman, XRD, HRTEM, FESEM, EDAX, and Zeta potential analyses. Unlike traditional nanocomposite bed systems, this study utilized BCDs as a liquid-phase adsorbent for the regenerative adsorption of the environmentally harmful dye, methylene blue (MB), through an in-situ precipitation reaction. This involved the formation of BCDs-MB adduct via an electrostatic mechanism. The adsorption capacity and percentage of removal were remarkable at 605 mg g-1 and 64.7% respectively, exceeding various solid-based adsorption methods in the literature. The Langmuir isotherm and pseudo-second-order kinetics model provided an excellent fit for this system. The calculated thermodynamic parameter, Gibbs free energy change (ΔG) was negative, indicating a spontaneous, exothermic, and physisorption-based mechanism. The regenerative capacity of our system was further demonstrated by successfully extracting and recovering the MB dye (64%) using ethyl alcohol as the solvent. This method provides an efficient means of recovering valuable cationic organic dye compounds from contaminated environments.

Green synthesis of carbon quantum dots from teak leaves biomass for in situ precipitation and regenerative-removal of methylene blue-dye

The objective of this study was to completely eliminate environmentally harmful cationic organic dye from aqueous solutions using the one-step ultrasonication method, renowned for its energy efficiency, user-friendliness, and minimal requirement for chemical resources, making it particularly suitable for large-scale applications. To achieve effective environmental remediation, we employed carbon dots derived from teak leaf biomass (TBCDs) layered with graphene oxide. We conducted a thorough characterization of the TBCDs using UV-vis spectroscopy (with absorption peaks at λmax = 208 and 276 nm), FTIR spectroscopy (confirming the presence of various functional groups including -OH, -CH, C = O, COO-, C-O-C, and = C-H), Raman spectroscopy (with bands at 1369 cm-1 (D-Band) and 1550 cm-1 (G-Band), and an intensity ratio (ID/IG) = 0.88, indicating structural defects correlated with the sp3 hybridization sites on the TBCDs), XRD analysis (indicating an amorphous nature of particles), HRTEM imaging (showing homogeneous dispersal of TBCDs with typical sizes ranging from 2 to 10 nm), FESEM analysis (showing a flat surface and minuscule particles), and Zeta potential analysis (revealing a surface charge peak at -51.0 mV). Our adsorption experiments yielded significant results, with a substantial 50.1 % removal rate and an impressive adsorption capacity of 735.2 mg g-1. Theoretical adsorption parameters were rigorously analyzed to understand the adsorption behavior, surface interactions, and mechanisms. Among these models, the Langmuir isotherm in conjunction with pseudo-second-order kinetics provided an exceptional fit (with R2 values closer to 1) for our system. The Gibbs free energy (ΔG) was found to be negative at all temperatures, indicating the spontaneity of the reaction. Regarding mechanism, electrostatic attraction ((+ve) MB dye + (- ve) TBCDs), π-π stacking adsorption facilitated by the graphitic structure, formation of multiple hydrogen bonds due to polar functional groups, and a pore-filling mechanism wherein the cationic MB dye fills the pores of TBCDs with graphene oxide layers, forming an adduct were identified. Furthermore, we demonstrated the regenerative capacity of our system by effectively extracting and recovering the MB dye (with a regeneration rate of 77.1%), utilizing ethyl alcohol as the solvent. These findings not only provide valuable insights into the adsorption capabilities of TBCDs but also highlight the potential of our approach in the recovery of expensive cationic organic dye compounds from polluted environments.

Flexible Synthesis of Bio-Hydroxyapatite/Chitosan Hydrogel Beads for Highly Efficient Orange G Dye Removal: Batch and Recirculating Fixed-Bed Column Study

The use of fish waste as a source material for the development of functional beads has significant potential applications in the fields of materials science and environmental sustainability. In this study, a biomaterial bead of chitosan was cross-linked with bio-hydroxyapatite (Bio-Hap/Cs) through the encapsulation process to create a stable and durable material. The beads are characterized using scanning electron microscopy combined with energy dispersive X-ray spectrometry, Fourier transform infrared spectroscopy, and X-ray diffraction techniques. The adsorption efficiency of Bio-Hap/Cs hydrogel beads was evaluated by using Orange G (OG) dye in both batch and recirculating column systems, and the effect of various parameters on the adsorption capacity was investigated. In the batch study, it was found that OG removal increased with an increasing pH and adsorbent dose. However, in the recirculating column system, a higher bed height and lower flow rate led to increased removal of the OG dye. The kinetic study indicated that the pseudo-second-order model provided a good description of OG adsorption onto Bio-Hap/Cs beads in both batch and recirculating processes, with a high coefficient correlation. The maximum adsorbed amounts are found to be 19.944 mg g-1 and 9.472 mg g-1 in batch and recirculating processes, respectively. Therefore, Bio-Hap/Cs hydrogel beads have demonstrated an effective and reusable material for OG dye remediation from aqueous solutions using recirculating adsorption processes.

Adsorption of Eosin B from Wastewater onto the Prepared Porous Anion Exchange Membrane

This research describes the fabrication of the porous trimethylamine (TMA)-grafted anion exchange membrane (AEM) over a phase inversion process. The synthesis of the generated AEM was verified using Fourier transform infrared (FTIR) spectroscopy. The fabricated porous AEM showed 240% water uptake (WR), 1.45 mg/g ion exchange capacity (IEC), and a 9.0% linear expansion ratio (LER) at 25 °C. It exhibited a porous structure and higher thermal stability. It was utilized to remove eosin B (EB) from wastewater via the process of adsorption. The adsorption capacity of EB increased with time and the starting concentration of EB while decreasing with temperature and the AEM dosage. Adsorption isotherm investigation results showed that EB adsorption onto the porous AEM followed the Langmuir isotherm because the value of correlation coefficient (R2 = 0.992) was close to unity. Because the correlation coefficient was close to one, it was determined through adsorption kinetic experiments that the adsorption of EB on the produced porous AEM was suitable for a pseudo-second-order model. Thermodynamic study about process of EB adsorption on the porous AEM revealed that there was an exothermic (ΔH° = -16.60 kJ/mol) and spontaneous process.

Decolorization, degradation and detoxification of mutagenic dye Methyl orange by novel biofilm producing plant growth-promoting rhizobacteria

Discharge of untreated dyeing wastewater nearby water-bodies is one of major causes of water pollution. Generally, bacterial strains isolated from industrial effluents and/or contaminated soils are used for the bioremediation of Methyl orange (MO), a mutagenic recalcitrant mono-azo dye, used in textiles and biomedical. However, MO degradation by biofilm producing plant growth-promoting rhizobacteria (BPPGPR) was not studied yet. In this study, 19 out of 21 BPPGPR strains decolorized 96.3-99.9% and 89.5-96.3% MO under microaerophilic and aerobic conditions, respectively from Luria-Bertani broth (LBB) followed by yeast-extract peptone and salt-optimized broth plus glycerol media within 120 h of incubation at 28 °C. Only selected BPPGPR including Pseudomonas fluorescens ESR7, P. veronii ESR13, Stenotrophomonas maltophilia ESR20, Staphylococcus saprophyticus ESD8, and P. parafulva ESB18 were examined for process optimization of MO decolorization using a single factor optimization method. This study showed that under optimal conditions (e.g., LBB, 100 mg L-1 MO, pH 7, incubation of 96 h, 28 °C), these strains could remove 99.1-99.8% and 97.6-99.5% MO under microaerophilic and aerobic conditions, respectively. Total azoreductase and laccase activities responsible for biodegradation were also remarkably activated in the biodegraded samples under optimal conditions, while these activities were repressed under unfavorable conditions (e.g., 40 °C and 7.5% NaCl). This study confirmed that MO was degraded and detoxified by these bacterial strains through breakage of azo bond. So far, this is the first report on bioremediation of MO by the BPPGPR strains. These BPPGPR strains are highly promising to be utilized for the bioremediation of dyeing wastewater in future.

Nanoporous hydrogel absorbent based on salep: Swelling behavior and methyl orange adsorption capacity

This study used the gas-blowing method to develop a nanoporous hydrogel using poly (3-sulfopropyl acrylate-co-acrylic acid-co-acrylamide) grafted onto salep. The synthesis of the nanoporous hydrogel was optimized by various parameters for maximum swelling capacity. The nanoporous hydrogel was characterized using FT-IR, TGA, XRD, TEM, and SEM analyses. Images from SEM showed numerous pores and channels in the hydrogel with an average size of about 80 nm, forming a honeycomb-like shape. The change in surface charge was investigated by zeta potential and revealed that the surface charge of the hydrogel ranged from 20 mV at acidic conditions to -25 mV at basic conditions. The swelling behavior of optimum superabsorbent hydrogel was determined under different environmental conditions, such as different pH values, ionic strengths of the environment, and solvents. In addition, the swelling kinetics and the absorbance under loading of the hydrogel sample in different environments were investigated. Moreover, Methyl Orange (MO) dye was removed from aqueous solutions using the nanoporous hydrogel as an adsorbent. The adsorption behavior of the hydrogel was examined under various conditions, and the adsorption capacity of the hydrogel was found tobe 400 mg g^-1. The maximum water uptake was obtained under the following conditions: Salep weight = 0.01 g, AA = 60 μL, MBA = 300 μL, APS = 60 μL, TEMED = 90 μL, AAm = 600 μL, and SPAK = 90 μL. Lastly, the adsorption kinetics was studied by employing pseudo-first-order, pseudo-second-order, and intra-particle diffusion models.

Design of tropinium-functionalized anion exchange membranes for acid recovery via diffusion dialysis process

Diffusion dialysis (DD) process utilizing anion exchange membranes (AEMs) is an environmentally-friendly and energy-efficient technology. From acidic wastewater, DD is needed for acid recovery. This research reports the development of a series of dense tropinium-functionalized AEMs via solution casting method. Fourier Infrared transform (FTIR) spectroscopy verified the successful preparation of AEMs. The developed AEMs exhibited a dense morphology, featuring 0.98-2.42 mmol/g of ion exchange capacity (IEC), 30-81% of water uptake (W_R) and 7-32% of linear swelling ratio (LSR). They displayed exceptional mechanical, thermal and chemical stability and were employed for acid waste treatment from HCl/FeCl₂ mixtures via DD process. AEMs possessed 20 to 59 (10^-3 m/h) and 166 to 362 of acid diffusion dialysis coefficient (U_H⁺) and separation factor (S) respectively at 25 °C. Compared to DF-120 commercial membrane (U_H⁺ = 0.004 m/h, S = 24.3), their DD efficiency was improved under identical experimental conditions.

Application of QPPO/PVA based commercial anion exchange membrane as an outstanding adsorbent for the removal of Eosin-B dye from wastewaters

Commercially available QPPO/PVA based anion exchange membrane (AEM) BIII was to inquire the percentage discharge of anionic dye Eosin-B (EB) at terrain temperature from wastewater. The impact of EB initial concentration, membrane dosage, ionic strength, contact time and temperature on EB percentage removal was contemplated. The EB percentage removal was increased from 22 to 99.56% and 38.15-99.56% with contact time and membrane dosage respectively while decreased from 99.56 to 29%, 99.56 to 54.61% and 99.56 to 92.22% with enhancing initial concentration of EB, ionic strength and temperature respectively. Nonlinear isotherm models were utilized to demonstrate EB adsorption onto AEM BIII. Attained results exhibited that nonliner Freundlich isotherm model best fitted to EB adsorption onto AEM BIII. For EB adsorption onto AEM BIII, adsorption kinetics were inquired in detail by using several kinetic models but EB adsorption nicely fitted to pseudo-second-order kinetics. Similarly thermodynamic analysis was performed and results pointed to an exothermic adsorption of EB onto AEM BIII. The membrane could be reused for four concecutive cycles with loosing its efficiency.

Fabrication of trimethylphosphine-functionalized anion exchange membranes for desalination application via electrodialysis process

The design of conductive, improved durable and selective anion exchange membranes (AEMs) for desalination application via electrodialysis (ED) process is critical for a more sustainable future. This work reports the design of a series of homogeneous trimethylphosphine (TMP)-functionalized anion exchange membranes (AEMs) for desalination application via electrodialysis (ED) process. Physico-chemical characterization and electrochemical performance of the trimethylphosphine-functionalized anion exchange membranes was conducted and the activity found to be tuned by varying the quantity of trimethylphosphine into the membrane architecture. For anion exchange membranes M1 to M4, the ion exchange capacity (IEC) was increased from 1.35 to 2.16 mmol/g, water uptake (W_R) from 4.30 to 17.72%, linear expansion ratio (LER) from 3.70 to 12.50% with enhancing the quantity of trimethylphosphine into the polymer architecture. The ionic resistance decreased from 15.14 to 2.61 Ω cm² with increasing quantities of trimethylphosphine whereas transport number increased from 0.98 to 0.99. The performance of synthesized trimethylphosphine-functionalized anion exchange membranes in desalination of NaCl was evaluated via electrodialysis process (flux of 3.42 mol/m². h and current efficiency of 64.30%). Results showed that the prepared trimethylphosphine-functionalized membrane (optimum M4) possess improved desalination performance as compared to commercial membrane Neosepta AMX under identical experimental conditions.