Fabrication of a GNP/Fe-Mg Binary Oxide Composite for Effective Removal of Arsenic from Aqueous Solution

Microwave engineered NiZrO3@GNP as efficient electrode material for energy storage applications

Supercapacitors (SCs) have emerged as attractive energy storage devices due to their rapid charge/discharge rates, long cycle life, and high-power density. However, the development of innovative electrode materials to achieve high-performance remains crucial to meet future requirements in supercapacitor technology. In this work, we have explored the potential of a microwave-engineered NiZrO3@GNP composite as a promising electrode material for SCs. A microwave assisted hydrothermal approach was adopted for the fabrication of the NiZrO3@GNP nanocomposite. Structural and morphological investigations showed its structural richness and its chemical compositions. When applied as a SC electrode, this innovative combination exhibits battery-like behaviour with higher specific capacity (577.63 C g-1) with good cyclic stability, and good performance. We have assembled an asymmetric-type two-electrode SC device and analysed its electrochemical features. This NiZrO3@GNP device exhibits the specific capacity of 47 C g-1 with capacitance retention of 70% after 2000 charge-discharge cycles. Further research on optimizing the synthesis process and exploring different device configurations could pave the way for even higher-performance supercapacitors in the future.

Optimization Study of the Capacity of Chlorella vulgaris as a Potential Bio-Remediator for the Bio-Adsorption of Arsenic (III) from Aquatic Environments

This study examined the ability of the green microalgae Chlorella vulgaris to remove arsenic from aqueous solutions. A series of studies was conducted to determine the optimal conditions for biological arsenic elimination, including biomass amount, incubation time, initial arsenic level, and pH values. At 76 min, pH 6, 50 mgL^-1 metal concentration, and 1 gL^-1 bio-adsorbent dosage, the maximum removal of arsenic from an aqueous solution was 93%. The uptake of As (III) ions by C. vulgaris reached an equilibrium at 76 min of bio-adsorption. The maximum adsorptive rate of arsenic (III) by C. vulgaris was 55 mg/gm. The Langmuir, Freundlich, and Dubinin-Radushkevich equations were used to fit the experimental data. The best theoretical isotherm of Langmuir, Freundlich, or/and Dubinin-Radushkevich for arsenic bio-adsorption by Chlorella vulgaris was determined. To choose the best theoretical isotherm, the coefficient of correlation was used. The data on absorption appeared to be linearly consistent with the Langmuir (q_max = 45 mgg^-1; R² = 0.9894), Freundlich (k_f = 1.44; R² = 0.7227), and Dubinin-Radushkevich (q_D-R = 8.7 mg/g; R² = 0.951) isotherms. The Langmuir and Dubinin-Radushkevich isotherms were both good two-parameter isotherms. In general, Langmuir was demonstrated to be the most accurate model for As (III) bio-adsorption on the bio-adsorbent. Maximum bio-adsorption values and a good correlation coefficient were observed for the first-order kinetic model, indicating that it was the best fitting model and significant in describing the arsenic (III) adsorption process. SEM micrographs of treated and untreated algal cells revealed that ions adsorbed on the algal cell's surface. A Fourier-transform infrared spectrophotometer (FTIR) was used to analyze the functional groups in algal cells, such as the carboxyl group, hydroxyl, amines, and amides, which aided in the bio-adsorption process. Thus, C. vulgaris has great potential and can be found in eco-friendly biomaterials capable of adsorbing arsenic contaminants from water sources.

High Entropy Oxide (CrMnFeNiMg)3 O4 with Large Compositional Space Shows Long-Term Stability as Cathode in Lithium-Sulfur Batteries

The repeated formation and irreversible diffusion of liquid-state lithium polysulfides (LiPSs) are the primary challenges in the development of high-energy-density lithium-sulfur battery (LSB). An effective strategy to alleviate the resulting polysulfide loss is critical for the stability of LSBs. In this regard, high entropy oxides (HEOs) appear as a promising additive for the adsorption and conversion of LiPSs owing to the diverse active sites, offering unparalleled synergistic effects. Herein, we have developed a (CrMnFeNiMg)₃ O₄ HEO as a functional polysulfide trapper in LSB cathode. The adsorption of LiPSs by the metal species (i. e., Cr, Mn, Fe, Ni, and Mg) in the HEO takes place through two different paths and leads to enhanced electrochemical stability. We demonstrate that the optimal sulfur cathode with the (CrMnFeNiMg)₃ O₄ HEO attains a high peak and reversible discharge capacities of 857 mAh g^-1 and 552 mAh g^-1 , respectively, at a cycling rate of C/10, a long cycle life of 300 cycles, and a high rate performance at the cycling rates from C/10 to C/2.

Removal of As(III)/As(V) from aqueous solution using newly developed thiosalicylic acid coated magnetite [TSA@Fe3O4] nanoparticles

The aim of this study was to develop an affordable adsorption methodology for removal of As(III)/As(V) from contaminated water. Herein, novel adsorbent TSA@Fe₃O₄ nanoparticles (NPs) were synthesized by decorating thiosalicylic acid (TSA) on magnetite nanoparticles (Fe₃O₄ NPs) and employed for removal of As(III)/As(V) species from artificially contaminated natural water systems. TSA@Fe₃O₄ NPs demonstrated excellent adsorption efficiency (AE) and 98% of As(V) and 93% of As(III) was removed at optimized experimental conditions. The adsorption kinetic and equilibrium isotherm studies were conducted preferentially for As(III) adsorption. Adsorption followed the pseudo-second-order kinetic (R² = 99%) and adsorption data fitted well in Langmuir isotherm model (R² = 99%) and maximum adsorption capacity (Q_max = 34.1 mg/g) was calculated for 5 mg/L of As(III) by using 10 mg of TSA@Fe₃O₄ NPs. The effect of pH, contact time, adsorption dosages, and competitive anions was also examined to identify optimum experimental conditions. The adsorbent was characterized by advanced instrumental techniques to investigate the physicochemical properties and stability of NPs. To comprehend the interactions of As(III) species with adsorbent NPs, NPs were analyzed using XPS and Raman spectroscopy techniques. Both the techniques confirmed that As(III) and As(V) species present simultaneously on adsorbent surface. The TSA@Fe₃O₄ was regenerated using 0.1 M NaOH. The findings of this study suggested that TSA@Fe₃O₄ NPs could be considered a potential adsorbent for effective remediation of As(III) and As(V) from contaminated natural water systems.

A review on current progress of graphene-based ternary nanocomposites in the removal of anionic and cationic inorganic pollutants

The current review aims to summarize the ongoing advances in high-performing graphene-based ternary nanocomposites for removing cationic and anionic inorganic pollutants. Graphene derivatives are extensively utilized for the development of composites due to their high synergism with co-functional materials, rational design, flexible surface chemistry, high mobile charge carriers, improved binding properties, and many more. The past ten years have witnessed progressive research on graphene-based ternary nanocomposites in a multitude of pollution remediation applications. Therefore, the focus falls on understanding how these ternary nanocomposites are tailored to capture the inorganic cationic and anionic contaminants with particular emphasis on graphene derivatives as base matrix and filler. The review investigates the synthesis, categorization, and characterization techniques of graphene-based ternary composites. Besides, the study broadens the understanding of the binding mechanism of the pollutants onto graphene ternary composites. The review also assesses the separation and recycling efficacy of the composites in detail. The future prospects in improving the practical application of the ternary systems also have been discussed. The comprehensive review on graphene based ternary systems detailing their structural and functional aspects, as well as their performance as inorganic decontaminants can provide deep insights for researchers in improvising wastewater treatment technologies.

Development of a Controlled Injection Method Using Support Templates for the Production of Chemobrionic Materials

Chemobrionics is a research field about the well-known self-organized inorganic structures. Numerous research works have focused on controlling their growth pattern and characteristic features. In the present study, a controlled injection method is proposed to produce more regular self-assembled chemobrionics compared to the standard direct injection technique. This method involves the injection of a metal salt solution into an agarose support template filled with an anionic solution. The obtained structures were studied by scanning electron microscopy, X-ray microtomography, X-ray photoelectron spectroscopy, Raman spectroscopy, Fourier-transform IR spectroscopy, and thermogravimetric analysis. Despite the complex mechanism and chemistry underlying the self-organization phenomena, the controlled injection method enabled the generation of regular standard chemobrionic structures with high experimental reproducibility. It provided the extraction of tubular structures from the reaction vessel without breakage, thus allowing comprehensive characterization. Furthermore, the morphological, chemical, and thermal features of these structures were highly correlated with the standard chemobrionics obtained in the direct injection method. The proposed controlled injection method holds great promise for understanding and controlling the properties of chemobrionics and related structures.

Dioctyl Phthalate-Modified Graphene Nanoplatelets: An Effective Additive for Enhanced Mechanical Properties of Natural Rubber

Graphene has been extensively considered an ideal additive to improve the mechanical properties of many composite materials, including rubbers, because of its novel strength, high surface area, and remarkable thermal and electron conductivity. However, the pristine graphene shows low dispersibility in the rubber matrix resulting in only slightly enhanced mechanical properties of the rubber composite. In this work, graphene nanoplatelets (GNPs) were modified with dioctyl phthalate (DOP) to improve the dispersibility of the graphene in the natural rubber (NR). The distribution of the DOP-modified GNPs in the NR matrix was investigated using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. The effect of the modified GNPs’ contents on the mechanical properties of the GNPs/NR composite was studied in detail. The results showed that the abrasion resistance of the graphene-reinforced rubber composite significantly improved by 10 times compared to that of the rubber without graphene (from 0.3 to 0.03 g/cycle without and with addition of the 0.3 phr modified GNPs). The addition of the modified GNPs also improved the shear and tensile strength of the rubber composite. The tensile strength and shear strength of the NR/GNPs composite with a GNPs loading of 0.3 phr were determined to be 23.63 MPa and 42.69 N/mm, respectively. Even the presence of the graphene reduced the other mechanical properties such as Shore hardness, elongation at break, and residual elongation; however, these reductions were negligible, which still makes the modified GNPs significant as an effective additive for the natural rubber in applications requiring high abrasion resistance.

Instructive analysis of engineered carbon materials for potential application in water and wastewater treatment

Water remediation is an essential component for sustainable development. Increasing population and rapid industrialization have contributed to the deterioration of water resources. In particular, effluents from chemical, pharmaceutical, petroleum industries, and anthropogenic activities have led to severe ecological degradation. Many of these detrimental pollutants are highly toxic even at low concentrations, acting as carcinogens and inflicting severe long-lasting effects on human health. This review underscores the potential applications of engineered carbon-based materials for effective wastewater treatment. It focuses on the performance as well as efficiency of activated carbon, graphene nanomaterial, and carbon nanotubes, both with and without chemical functionalization. Plausible mechanisms of action between the chemically functionalized adsorbent and pollutants are also discussed. Based on the keywords from the literature published in the recent five years, a statistical practicality-vs-applicability analysis of these three materials is also provided. The review will provide a deep understanding of the physical or chemical interactions of the wastewater pollutants with carbon materials.

Photoassisted Electron-Ion Synergic Doping Induced Phase Transition of n-VO2/p-GaN Thin-Film Heterojunction

As a typical correlated metal oxide, vanadium dioxide (VO₂) shows specific metal-insulator transition (MIT) properties and demonstrates great potential applications in ultrafast optoelectronic switch, resistive memory, and neuromorphic devices. Effective control of the MIT process is essential for improving the device performance. In the current study, we have first proposed a photoassisted ion-doping method to modulate the phase transition of the VO₂ layer based on the photovoltaic effect and electron-ion synergic doping in acid solution. Experimental results show that, for the prepared n-VO₂/p-GaN nanojunction, this photoassisted strategy can effectively dope the n-VO₂ layer by H⁺, Al³⁺, or Mg²⁺ ions under light radiation and trigger consecutive insulator-metal-insulator transitions. If combined with standard lithography or electron beam etching processes, selective doping with nanoscale size area can also be achieved. This photoassisted doping method not only shows a facile route for MIT modulation via a doping route under ambient conditions but also supplies some clues for photosensitive detection in the future.

Smectite-supported chain of iron nanoparticle beads for efficient clean-up of arsenate contaminated water

Prolonged exposure to inorganic arsenic (As) via drinking water is a major concern as it poses significant human health risks. Removal of As is crucial but requires effective and environment-friendly clean-up technology to avoid any additional risk to the environment. In this study, we developed Australian smectite (smec)-supported nano zero-valent iron (nZVI) composite for arsenate i.e., As(V) sorption. We used a range of tools, including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) and energy dispersion X-ray (EDS) spectroscopy to characterise the material. SEM and TEM images and elemental mapping of the composite reflect that the smectite layer was surrounded by a chain of iron nanobeads evenly distributed on clay particles, which is quite exceptional among currently available nZVIs. The maximum As(V) sorption capacity of this composite was 23.12 mg/g in the ambient conditions. Using X-ray photoelectron spectroscopy we unveiled chemical states of As and Fe before and after the sorption process. Additionally, the release of iron nanoparticles from the composite at various pHs (3-10) were found negligible, which demonstrates the effectiveness of smec-nZVI to remove As(V) from contaminated water without posing any secondary pollutant.

Evaluation of Fe-Mg Binary Oxide for As (III) Adsorption-Synthesis, Characterization and Kinetic Modelling

Nanotechnology has received much attention in treating contaminated waters. In the present study, a facile co-precipitation method was employed to synthesize a novel iron and magnesium based binary metal oxide using a stoichiometrically fixed amount of FeNO₃·9H₂O and MgNO₃·6H₂O in a proportion of molar concentration 1:1 and was later evaluated in removing As (III) from contaminated waters. Characterization of the prepared nanomaterial was done using X-ray diffraction (XRD), scanning electron microscopy (SEM), Energy Dispersive X-ray Analysis (EDAX) and ultraviolet–visible spectrophotometry (UV-VIS). Experimental studies on batch scale were carried out, examining the effect of varying initial concentrations of metal, adsorbent dosage, application time and initial pH on removal efficiency. Arsenic removal increased on increasing adsorbent dosage (0.1–1 g/L) but trend reversed on increasing initial arsenic concentration attaining q_max of 263.20 mg/g. Adsorption was quite efficient in pH range 4–8. Freundlich fitted better for adsorption isotherm along with following Pseudo-2nd order kinetics. The reusability and effect of co-existing ions on arsenic adsorption, namely SO₄²⁻, CO₃²⁻ and PO₄³⁻ were also explored with reusability in 1st and 2nd cycles attained adsorptive removal up to 77% and 64% respectively. The prepared nano-adsorbent showed promising results in terms of high arsenic uptake (q_max of 263.20 mg/g) along with facile and cost-effective synthesis. Thus, the co-precipitation technique used in this work is a simple one step procedure without any use of any precursor as compared to most of the other procedures used for synthesis.

Recent Advances of Graphene-Based Strategies for Arsenic Remediation

The decontamination of water containing toxic metals is a challenging problem, and in the last years many efforts have been undertaken to discover efficient, cost-effective, robust, and handy technology for the decontamination of downstream water without endangering human health. According to the World Health Organization (WHO), 180 million people in the world have been exposed to toxic levels of arsenic from potable water. To date, a variety of techniques has been developed to maintain the arsenic concentration in potable water below the limit recommended by WHO (10 μg/L). Recently, a series of technological advancements in water remediation has been obtained from the rapid development of nanotechnology-based strategies that provide a remarkable control over nanoparticle design, allowing the tailoring of their properties toward specific applications. Among the plethora of nanomaterials and nanostructures proposed in the remediation field, graphene-based materials (G), due to their unique physico-chemical properties, surface area, size, shape, ionic mobility, and mechanical flexibility, are proposed for the development of reliable tools for water decontamination treatments. Moreover, an emerging class of 3D carbon materials characterized by the intrinsic properties of G together with new interesting physicochemical properties, such as high porosity, low density, unique electrochemical performance, has been recently proposed for water decontamination. The main design criteria used to develop remediation nanotechnology-based strategies have been reviewed, and special attention has been reserved for the advances of magnetic G and for nanostructures employed in the fabrication of membrane filtration.

Ultra-high arsenic adsorption by graphene oxide iron nanohybrid: Removal mechanisms and potential applications

Iron (Fe)-based adsorbents have been promoted for aqueous arsenic adsorption because of their low cost and potential ease of scale-up in production. However, their field application is, so far, limited because of their low Fe use efficiency (i.e., not all available Fe is used), slow adsorption kinetics, and low adsorption capacity. In this study, we synthesized graphene oxide iron nanohybrid (GFeN) by decorating iron/iron oxide (Fe/Fe_xO_y) core-shell structured iron nanoparticles (FeNPs) on the surface of graphene oxide (GO) via a sol-gel process. The deposition of FeNPs on GO for the nanohybrid (GFeN) improves Fe use efficiency and arsenic mobility in the nanohybrid, thereby improving the arsenic removal capacity and kinetics. We achieved removal capacities of 306 mg/g for As(III) and 431 mg/g for As(V) using GFeN. Rapid reduction (>99% in <10 min) of As(III) and As(V) (initial concentration, C₀ = 100 μg/L) was achieved with the nanohybrid (250 mg/L). There were no significant interferences by the coexisting anions and organic matters at environmentally relevant concentrations. Based on the experimental data, we have proposed that both electrostatic interaction and surface complexation contributed to ultra-high arsenic removal by GFeN. The GO sheets acted as the reservoirs for the electrons released during surface corrosion of the FeNPs and the electrons were transferred back to the FeNPs to rejuvenate the oxidized surface. The rejuvenated FeNP surface layer helped in additional arsenic removal.

Scalable Fabrication of Modified Graphene Nanoplatelets as an Effective Additive for Engine Lubricant Oil

The use of nano-additives is widely recognized as a cheap and effective pathway to improve the performance of lubrication by minimizing the energy loss from friction and wear, especially in diesel engines. In this work, a simple and scalable protocol was proposed to fabricate a graphene additive to improve the engine lubricant oil. Graphene nanoplates (GNPs) were obtained by a one-step chemical exfoliation of natural graphite and were successfully modified with a surfactant and an organic compound to obtain a modified GNP additive, that can be facilely dispersed in lubricant oil. The GNPs and modified GNP additive were characterized using scanning electron microscopy, X-ray diffraction, atomic force microscopy, Raman spectroscopy, and Fourier-transform infrared spectroscopy. The prepared GNPs had wrinkled and crumpled structures with a diameter of 10–30 µm and a thickness of less than 15 nm. After modification, the GNP surfaces were uniformly covered with the organic compound. The addition of the modified GNP additive to the engine lubricant oil significantly enhanced the friction and antiwear performance. The highest reduction of 35% was determined for the wear scar diameter with a GNP additive concentration of approximately 0.05%. The mechanism for lubrication enhancement by graphene additives was also briefly discussed.

Adsorption of arsenic using chitosan magnetic graphene oxide nanocomposite

Chitosan-magnetic-graphene oxide (CMGO) nanocomposite was prepared for arsenic adsorption. The nanocomposite was characterized through BET, FTIR, FESEM, EDX, and VSM analyses. These characterizations confirmed the formation of CMGO nanocomposites with high specific surface area (152.38 m²/g) and excellent saturation magnetization (49.30 emu/g). Batch adsorption experiments were conducted to evaluate the performance of the nanocomposite in the adsorption of arsenic from aqueous solution. The effects of operational parameters, adsorption kinetic, equilibrium isotherm and thermodynamics were evaluated. The removal efficiency of arsenic increased with increasing adsorbent dosage and contact time. However, the effect of pH followed a different pattern, with the removal efficiency increasing from acidic to neutral pH, and then decreasing at alkaline conditions. The highest adsorption capacity (45 mg/g) and removal efficiency (61%) were obtained at pH 7.3. The adsorption kinetic followed a pseudo-second-order kinetic model. The analysis of adsorption isotherm shows that the adsorption data fitted well to Langmuir isotherm model, indicating a homogeneous process. Thermodynamic analysis shows that the adsorption of As(III) is exothermic and spontaneous. The superparamagnetic properties of the nanocomposite enabled the separation and recovery of the nanoparticles using an external magnetic field. Thus, the developed nanocomposite has a potential for arsenic remediation.

Magnetite-Coated Boron Nitride Nanosheets for the Removal of Arsenic(V) from Water

It is widely known that the existence of arsenic (As) in water negatively affects humans and the environment. We report the synthesis, characterization, and application of boron nitride nanosheets (BNNSs) and Fe₃O₄-functionalized BNNS (BNNS-Fe₃O₄) nanocomposite for removal of As(V) ions from aqueous systems. The morphology, surface properties, and compositions of synthesized nanomaterials were examined using scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, surface area analysis, zero-point charge, and magnetic moment determination. The BNNS-Fe₃O₄ nanocomposites have a specific surface area of 119 m² g^-1 and a high saturation magnetization of 49.19 emu g^-1. Due to this strong magnetic property at room temperature, BNNS-Fe₃O₄ can be easily separated in solution by applying an external magnetic field. From the activation energies, it was found that the adsorption of As(V) ions on BNNSs and BNNS-Fe₃O₄ was due to physical and chemical adsorption, respectively. The maximum adsorption capacity of BNNS-Fe₃O₄ nanocomposite for As(V) ions has been found to be 26.3 mg g^-1, which is 5 times higher than that of unmodified BNNSs (5.3 mg g^-1). This closely matches density functional theory simulations, where it is found that binding energies between BNNS-Fe₃O₄ nanocomposite and As(OH)₅ are 5 times higher than those between BNNSs and As(OH)₅, implying 5 times higher adsorption capacity of BNNS-Fe₃O₄ nanocomposite than unmodified BNNSs. More importantly, it was observed that the synthesized BNNS-Fe₃O₄ nanocomposite could reduce As(V) ion concentration from 856 ppb in a solution to below 10 ppb (>98.83% removal), which is the permissible limit according to World Health Organization recommendations. Finally, the synthesized adsorbent showed both separation and regeneration properties. These findings demonstrate the potential of BNNS-Fe₃O₄ nanocomposite for commercial application in separation of As(V) ions from potable and waste water streams.

Development and regeneration of composite of cationic gel and iron hydroxide for adsorbing arsenic from ground water

Globally, arsenic contaminated groundwater is a serious concern for human health. Previous studies have developed various methods to remove arsenic. But, most of them fail to selectively adsorb arsenic and regenerate. In this study, we developed an adsorbent, a cationic polymer gel loaded with iron hydroxide, which can adsorb arsenic from groundwater more effectively than the other adsorbents. The cationic polymer gel is N,N-dimethylamino propylacrylamide, methyl chloride quaternary (DMAPAAQ). The preparation of the gel is different from the other polymer gels used for adsorption of arsenic and other metals, and it ensures that the gel contains 53.7% FeOOH particles. It should also provide good selectivity, be simple to use and be cost-effective in terms of reusability. The study showed that the gel selectively adsorbed arsenic effectively at neutral pH levels. The results demonstrate that the maximum amount of As(V) adsorption was 123.4 mg/g, which is higher than the other adsorbents. In addition, the gel adsorbed As(V) selectively in the presence of Sulphate. Also, regeneration of the gel was performed for eight consecutive days with 87.6% effectiveness. Additionally, the adsorption mechanism of this gel composite and time required for reaching the equilibrium adsorption is discussed in this paper.

A New Approach of Fabricating Graphene Nanoplates@Natural Rubber Latex Composite and Its Characteristics and Mechanical Properties

Graphene has been demonstrated to be one of the most promising candidates to use as filler to improve the electrical, thermal, chemical and mechanical properties of natural rubber due to exceptional high surface area, superior electrical and thermal conductivity, and remarkable gas impermeability resistance. In this study, graphene nanoplates (GNPs) were mass-produced by a one-step chemical exfoliation of natural graphite and used as a filler for the fabrication of GNPs@natural rubber composite by a simple mixing method. The resultant GNPs/rubber composite was characterized by using scanning electron microscopy (SEM), and a rheometer. The prepared graphene nanoplates had a thickness of less than 10 nm and a lateral size of tens of microns. The GNPs@rubber composite revealed an exceptional improvement of abrasion loss up to seven to ten fold, along with an approximately 400%, 200% and 30% increment of elongation at break, tear strength and tensile strength, respectively. Other mechanical properties, such as hardness, compression set and rebound, as well as the effect of the GNPs loadings on the mechanical properties of the composite, were also investigated in detail.

Removal of arsenate and dichromate ions from different aqueous media by amine based p(TAEA-co-GDE) microgels

In this work, microgels based on tris(2-aminoethyl) amine (TAEA) and glycerol diglycidyl ether (GDE) via simple microemulsion polymerization was prepared as p(TAEA-co-GDE) microgels were used as adsorbent for removal of dichromate (Cr (VI)) and arsenate (As (V)) ions from different aqueous environments. The p(TAEA-co-GDE) microgels were demonstrated very efficient adsorption capacity for Cr (VI), and As (V) that are 164.98 mg/g, and 123.64 mg/g from distilled (DI) water, respectively. The effect of the medium pH on the adsorption capacity of p(TAEA-co-GDE) microgels for Cr (VI) and As (V) ions were investigated. The maximum adsorption capacity was obtained at pH 4.0 for both ions with maximum adsorbed amounts of 160.62, and 98.72 mg/g, respectively. In addition, the microgels were also shown moderate adsorption capacity for Cr (VI) and As (V) from other water sources; tap water with 115.18 mg/g and 82.86 mg/g, sea water with 64.24 mg/g and 46.88 mg/g and creek water with 73.52 mg/g and 59.33 mg/g, respectively. Moreover, the increase in adsorbent dose from 0.025 to 0.125 g enhanced % adsorption of Cr (VI) from 54.13 to 98.03, and As (V) from % 26.72-98.70, respectively. For the adsorption process Langmuir and Freundlich adsorption isotherms were applied and found that Langmuir adsorption isotherm with R² value of 0.99 for both the metal ions are suitable. Moreover, the experimental adsorption capacities of Cr (VI) and As (V) were found very close to the theoretical values calculated from Langmuir adsorption isotherm. More importantly, the microgels were made magnetic responsive to recover them easily from adsorption medium for reuse studies by applying external magnetic field with little decrease in adsorption capacity. Additionally, reusability of p(TAEA-co-GDE) microgels was also evaluated for adsorption of Cr (VI) and As (V) from DI water.

Graphene-Supported Spinel CuFe₂O₄ Composites: Novel Adsorbents for Arsenic Removal in Aqueous Media

A graphene nanoplate-supported spinel CuFe₂O₄ composite (GNPs/CuFe₂O₄) was successfully synthesized by using a facile thermal decomposition route. Scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), Electron Dispersive Spectroscopy (EDS), X-ray diffraction (XRD) and X-ray Photoelectron Spectroscopy (XPS) were employed to characterize the prepared composite. The arsenic adsorption behavior of the GNPs/CuFe₂O₄ composite was investigated by carrying out batch experiments. Both the Langmuir and Freundlich models were employed to describe the adsorption isotherm, where the sorption kinetics of arsenic adsorption by the composite were found to be pseudo-second order. The selectivity of the adsorbent toward arsenic over common metal ions in water was also demonstrated. Furthermore, the reusability and regeneration of the adsorbent were investigated by an assembled column filter test. The GNPs/CuFe₂O₄ composite exhibited significant, fast adsorption of arsenic over a wide range of solution pHs with exceptional durability, selectivity, and recyclability, which could make this composite a very promising candidate for effective removal of arsenic from aqueous solution. The highly sensitive adsorption of the material toward arsenic could be potentially employed for arsenic sensing.

Effective removal of Pb(ii) using a graphene@ternary oxides composite as an adsorbent in aqueous media

A one-pot hydrothermal method to prepare a graphene@Fe–Mg–Cu ternary oxide composite and the proposed adsorption mechanism for removal of Pb(ii) ions.