One-Step Synthesis of a Self-Supported Copper Phosphide Nanobush for Overall Water Splitting

Fabrication of Ru-doped CuMnBP micro cluster electrocatalyst with high efficiency and stability for electrochemical water splitting application at the industrial-level current density

Electrochemical water splitting has been considered as a key pathway to generate environmentally friendly green hydrogen energy and it is essential to design highly efficient electrocatalysts at affordable cost to facilitate the redox reactions of hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). In this work, a novel micro-clustered Ru/CuMnBP electrocatalyst is introduced, prepared via hydrothermal deposition and soaking-assisted Ru doping approaches on Ni foam substrate. Ru/CuMnBP micro-clusters exhibit relatively low HER/OER turnover overpotentials of 11 mV and 85 mV at 10 mA/cm2 in 1 M KOH. It also demonstrates a low 2-E turnover cell voltage of 1.53 V at 10 mA/cm2 for the overall water-splitting, which is comparable with the benchmark electrodes of Pt/C||RuO2. At a super high-current density of 2000 mA/cm2, the dual functional Ru/CuMnBP demonstrates an exceptionally low 2-E cell voltage of 3.13 V and also exhibits superior stability for over 10 h in 1 M KOH. Excellent electrochemical performances originate from the large electrochemical active surface area with the micro cluster morphology, high intrinsic activity of CuMnBP micro-clusters optimized through component ratio adjustment and the beneficial Ru doping effect, which enhances active site density, conductivity and stability. The usage of Ru in small quantities via the simple soaking doping approach significantly improves electrochemical reaction rates for both HER and OER, making Ru/CuMnBP micro-clusters promising candidates for advanced electrocatalytic applications.

Nanocomposites based on Cu2O coated silver nanowire networks for high-performance oxygen evolution reaction

The development of highly active, low-cost, and robust electrocatalysts for the oxygen evolution reaction (OER) is a crucial endeavor for the clean and economically viable production of hydrogen via electrochemical water splitting. Herein, cuprous oxide (Cu2O) thin films are deposited on silver nanowire (AgNW) networks by atmospheric-pressure spatial atomic layer deposition (AP-SALD). AgNW@Cu2O nanocomposites supported on conductive copper electrodes exhibited superior OER activity as compared to bare copper substrate and bare AgNWs. Moreover, a relationship between Cu2O thickness and OER activity was established. Notably, the most effective catalyst (AgNW@50nm-thick Cu2O) demonstrated very high OER activity with a low overpotential of 409 mV to deliver a current density of 10 mA cm-2 (η 10), a Tafel slope of 47 mV dec-1, a turnover frequency (TOF) of 4.2 s-1 at 350 mV, and good durability in alkaline media (1 M KOH). This highlights the potential of AgNWs as a powerful platform for the formation of highly efficient copper oxide catalysts towards OER. This work provides a foundation for the development of nanostructured Cu-based electrocatalysts for future clean energy conversion and storage systems.

Bifunctional Electrocatalysts for Overall and Hybrid Water Splitting

Electrocatalytic water splitting driven by renewable electricity has been recognized as a promising approach for green hydrogen production. Different from conventional strategies in developing electrocatalysts for the two half-reactions of water splitting (e.g., the hydrogen and oxygen evolution reactions, HER and OER) separately, there has been a growing interest in designing and developing bifunctional electrocatalysts, which are able to catalyze both the HER and OER. In addition, considering the high overpotentials required for OER while limited value of the produced oxygen, there is another rapidly growing interest in exploring alternative oxidation reactions to replace OER for hybrid water splitting toward energy-efficient hydrogen generation. This Review begins with an introduction on the fundamental aspects of water splitting, followed by a thorough discussion on various physicochemical characterization techniques that are frequently employed in probing the active sites, with an emphasis on the reconstruction of bifunctional electrocatalysts during redox electrolysis. The design, synthesis, and performance of diverse bifunctional electrocatalysts based on noble metals, nonprecious metals, and metal-free nanocarbons, for overall water splitting in acidic and alkaline electrolytes, are thoroughly summarized and compared. Next, their application toward hybrid water splitting is also presented, wherein the alternative anodic reactions include sacrificing agents oxidation, pollutants oxidative degradation, and organics oxidative upgrading. Finally, a concise statement on the current challenges and future opportunities of bifunctional electrocatalysts for both overall and hybrid water splitting is presented in the hope of guiding future endeavors in the quest for energy-efficient and sustainable green hydrogen production.

Redox Chemistries for Vacancy Modulation in Plasmonic Copper Phosphide Nanocrystals

Copper phosphide (Cu3-xP) nanocrystals are promising materials for nanoplasmonics due to their substoichiometric composition, enabling the generation and stabilization of excess delocalized holes and leading to localized surface plasmon resonance (LSPR) absorption in the near-IR. We present three Cu-coupled redox chemistries that allow postsynthetic modulation of the delocalized hole concentrations and corresponding LSPR absorption in colloidal Cu3-xP nanocrystals. Changes in the structural, optical, and compositional properties are evaluated by powder X-ray diffraction, electronic absorption spectroscopy, 31P magic-angle spinning solid-state nuclear magnetic resonance spectroscopy, and elemental analysis. The redox chemistries presented herein can be used to access nanocrystals with LSPR energies of 660-890 meV, a larger range than has been possible through synthetic tuning alone. In addition to utilizing previously reported redox chemistries used for copper chalcogenide nanocrystals, we show that the largest structural and LSPR modulation is achieved using a divalent metal halide and trioctylphosphine. Specifically, nanocrystals treated with zinc iodide and trioctylphosphine have the smallest unit-cell volume (295.2 Å3) reported for P63cm Cu3-xP, indicating more Cu vacancies than have been previously observed. Overall, these redox chemistries present valuable insight into controlling the optical and structural properties of Cu3-xP.

Transition Metals-Based Water Splitting Electrocatalysts on Copper-Based Substrates: The Integral Role of Morphological Properties

Electrocatalytic water splitting is a promising alternative to produce high purity hydrogen gas as the green substitute for renewable energy. Thus, development of electrocatalysts for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) are vital to improve the efficiency of the water splitting process particularly based on transition metals which has been explored extensively to replace the highly active electrocatalytic activity of the iridium and ruthenium metals-based electrocatalysts. In situ growth of the material on a conductive substrate has also been proven to have the capability to lower down the overpotential value significantly. On top of that, the presence of substrate has given a massive impact on the morphology of the electrocatalyst. Among the conductive substrates that have been widely explored in the field of electrochemistry are the copper based substrates mainly copper foam, copper foil and copper mesh. Copper-based substrates possess unique properties such as low in cost, high tensile strength, excellent conductor of heat and electricity, ultraporous with well-integrated hierarchical structure and non-corrosive in nature. In this review, the recent advancements of HER and OER electrocatalysts grown on copper-based substrates has been critically discussed, focusing on their morphology, design, and preparation methods of the nanoarrays.

Copper Selenophosphate, Cu3PSe4, Nanoparticle Synthesis: Octadecane Is the Key to a Simplified, Atom-Economical Reaction

Nanoparticle syntheses are designed to produce the desired product in high yield but traditionally neglect atom-economy. Here we report that the simple, but significant, change of the solvent from 1-octadecene (1-ODE) to the operationally inert octadecane (ODA) permits an atom-economical synthesis of copper selenophosphate (Cu3PSe4) nanoparticles. This change eliminates the competing selenium (Se) delivery pathways from our first report that required an excess of Se. Instead Se0powder is dispersed in ODA, which promotes a formal eight-electron transfer between Cu3-xP and Se0. Powder X-ray diffraction and transmission electron microscopy confirm the purity of the Cu3PSe4, while 1H and 13C NMR indicate the absence of oxidized ODA or Se species. We utilize the direct pathway to gain insights into stoichiometry and ligand identity using thermogravimetric analysis and X-ray photoelectron spectroscopy. Given the prevalence of 1-ODE in nanoparticle synthesis, this approach could be applied to other chalcogenide reaction pathways to improve stoichiometry and atom-economy.

A Review of Transition Metal Boride, Carbide, Pnictide, and Chalcogenide Water Oxidation Electrocatalysts

Transition metal borides, carbides, pnictides, and chalcogenides (X-ides) have emerged as a class of materials for the oxygen evolution reaction (OER). Because of their high earth abundance, electrical conductivity, and OER performance, these electrocatalysts have the potential to enable the practical application of green energy conversion and storage. Under OER potentials, X-ide electrocatalysts demonstrate various degrees of oxidation resistance due to their differences in chemical composition, crystal structure, and morphology. Depending on their resistance to oxidation, these catalysts will fall into one of three post-OER electrocatalyst categories: fully oxidized oxide/(oxy)hydroxide material, partially oxidized core@shell structure, and unoxidized material. In the past ten years (from 2013 to 2022), over 890 peer-reviewed research papers have focused on X-ide OER electrocatalysts. Previous review papers have provided limited conclusions and have omitted the significance of "catalytically active sites/species/phases" in X-ide OER electrocatalysts. In this review, a comprehensive summary of (i) experimental parameters (e.g., substrates, electrocatalyst loading amounts, geometric overpotentials, Tafel slopes, etc.) and (ii) electrochemical stability tests and post-analyses in X-ide OER electrocatalyst publications from 2013 to 2022 is provided. Both mono and polyanion X-ides are discussed and classified with respect to their material transformation during the OER. Special analytical techniques employed to study X-ide reconstruction are also evaluated. Additionally, future challenges and questions yet to be answered are provided in each section. This review aims to provide researchers with a toolkit to approach X-ide OER electrocatalyst research and to showcase necessary avenues for future investigation.

Fabrication of nanosheet-assembled hollow copper-nickel phosphide spheres embedded in reduced graphene oxide texture for hybrid supercapacitors

Owing to their metalloid characteristics with high electrical conductivity, transition metal phosphides (TMPs) have attracted considerable research attention as prospective cathodes for hybrid supercapacitors. Unfortunately, they usually exhibit low rate performance as well as poor longevity, which does not meet the demands of hybrid supercapacitors. The nanocomposite constructed from reduced graphene oxide (rGO) and TMPs with a highly porous nature can effectively overcome the above-mentioned issues, greatly widening their utilization. In this work, we fabricated nanosheet-assembled hollow copper-nickel phosphide spheres (NH-CNPSs) by the controllable phosphatizing of copper-nickel-ethylene glycol (CN-EG) precursors. Then, porous NH-CNPSs were embedded in rGO texture (NH-CNPS-rGO) to form a unique porous nanoarchitecture. The obtained NH-CNPS-rGO has several advantages benefiting as the cathode electrode, such as (i) the hollow structure as well as porous nanosheets are conducive to fast electrolyte diffusion, (ii) the electrical conductivity of NH-CNPS is further enhanced when coupled with the rGO texture, hence promoting electron transfer in the whole structure, (iii) wrapping NH-CNPSs within the rGO texture endows the nanocomposite with much better structural stability, resulting in longer durability of the electrode, And (iv) the porous structures generated in the nanocomposite provide a perfect space for reducing the mass transfer resistance and accessing the electrolyte, thereby boosting the reaction kinetics. The tests demonstrated that the optimal NH-CNPS-rGO electrode revealed a capacity of up to 1075 C g^-1, a superior rate capacity, and exceptional longevity of 94.7%. Moreover, a hybrid supercapacitor (NH-CNPS-rGO‖AC) equipped with the NH-CNPS-rGO-cathode electrode and activated carbon (AC)-anode electrode represented a satisfactory energy density of 64 W h kg^-1 at 801 W kg^-1 and amazing longevity (91.8% retention after 13 000 cycles), which endorses the promising potential of NH-CNPS-rGO for high-efficiency supercapacitors. This research showcases an appropriate method to engineer hollow TMP-rGO nanocomposites as effective materials for supercapacitors.

Electrochemical tuning of a Cu3P/Ni2P hybrid for a promoted hydrogen evolution reaction

Developing novel and high performance electrocatalysts for use in hydrogen evolution reactions (HER) as substitutes for noble metal based electrocatalysts is imperative and, so far, has been a challenge. Herein, a self-supported Cu₃P/Ni₂P hybrid on nickel foam (Cu₃P/Ni₂P@NF) is prepared by a simple galvanic replacement reaction coupled with phosphorization. Subsequently, Cu₃P/Ni₂P@NF is modified by conducting cyclic voltammetry scans in 0.5 M H₂SO₄ solution. Interestingly, after electrochemical tuning, the as-prepared Cu₃P/Ni₂P@NF exhibits significantly enhanced HER activity. Particularly, the resultant Cu₃P/Ni₂P@NF catalyst after 4000 cycles exhibits superior catalytic activity and long-term stability for HER with an overpotential of only 67 mV at the current density of 10 mA cm^-2, and a low Tafel slope of 43.9 mV dec^-1. The improved HER performance is attributed to the increased intrinsic activity of the Cu₃P/Ni₂P@NF with its optimized crystal and electronic structure, as well as an increased number of accessible active sites due to surface dissolution and recrystallization induced by electrochemical modification.

Ag Nanoparticle-Modified Polyoxometalate-Based Metal-Organic Framework for Enhanced CO2 Photoreduction

The photoreduction deposition method is employed to fabricate a family of silver nanoparticle (Ag NP)-modified polyoxometalate-based metal-organic framework (NENU-5) photocatalysts, named Ag/NENU-5. The title photocatalysts, Ag/NENU-5, can be used for the photocatalytic reduction of CO₂ and are observed to efficiently reduce CO₂ into CO, in which the highest reduction rate is 22.28 μmol g^-1 h^-1, 3 times greater than that of NENU-5. Photocatalytic reduction performances of CO₂ have been extremely improved after the incorporation of Ag NPs as the cocatalyst. The enhancement of the photocatalytic reduction of CO₂ has been attributed to the synergistic effects of Ag NPs and NENU-5, inhibiting the charge recombination during the photocatalytic process and increasing the reaction active sites. Furthermore, the influence of Ag NPs on the photocatalytic activity has also been investigated. The experimental results clearly reveal that the size of Ag NPs could exert a main effect on the photocatalytic activity, and the reasonable size of Ag NPs is able to enhance the photocatalytic reduction activity toward CO₂ significantly.

Synthesis of Self-Supported Cu/Cu3P Nanoarrays as an Efficient Electrocatalyst for the Hydrogen Evolution Reaction

Owing to the energy crisis and environmental pollution, it is essential to develop cheap, environmentally friendly and sustainable energy to replace noble metal electrocatalysts for use in the hydrogen evolution reaction (HER). We report herein that a Cu/Cu3P nanoarray catalyst was directly grown on the surfaces of Cu nanosheets from its Cu/CuO nanoarray precursor by a low-temperature phosphidation process. In particular, the effects of phosphating distance, mass ratio and temperature on the morphology of Cu/Cu3P nanoarrays were studied in detail. This nanoarray, as an electrocatalyst, displays excellent catalytic performance and long-term stability in an acid solution for electrochemical hydrogen generation. Specifically, the Cu/Cu3P nanoarray-270 exhibits a low onset overpotential (96 mV) and a small Tafel slope (131 mV dec−1).

Transition Metal Non-Oxides as Electrocatalysts: Advantages and Challenges

The identification of hydrogen as green fuel in the near future has stirred global realization toward a sustainable outlook and thus boosted extensive research in the field of water electrolysis focusing on the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and oxygen reduction reaction (ORR). A huge class of compounds consisting of transition metal-based nitrides, carbides, chalcogenides, phosphides, and borides, which can be collectively termed transition metal non-oxides (TMNOs), has emerged recently as an efficient class of electrocatalysts in terms of performance and longevity when compared to transition metal oxides (TMOs). Moreover, the superiority of TMNOs over TMOs to effectively catalyze not only OERs but also HERs and ORRs renders bifunctionality and even trifunctionality in some cases and therefore can replace conventional noble metal electrocatalysts. In this review, the crystal structure and phases of different classes of nanostructured TMNOs are extensively discussed, focusing on recent advances in design strategies by various regulatory synthetic routes, and hence diversified properties of TMNOs are identified to serve as next-generation bi/trifunctional electrocatalysts. The challenges and future perspectives of materials in the field of energy conversion and storage aiding toward a better hydrogen economy are also discussed in this review.

Electrochemically Derived Crystalline CuO from Covellite CuS Nanoplates: A Multifunctional Anode Material

In the present era, electrochemical water splitting has been showcased as a reliable solution for alternative and sustainable energy development. The development of a cheap, albeit active, catalyst to split water at a substantial overpotential with long durability is a perdurable challenge. Moreover, understanding the nature of surface-active species under electrochemical conditions remains fundamentally important. A facile hydrothermal approach is herein adapted to prepare covellite (hexagonal) phase CuS nanoplates. In the covellite CuS lattice, copper is present in a mixed-valent state, supported by two different binding energy values (932.10 eV for Cu^I and 933.65 eV for Cu^II) found in X-ray photoelectron spectroscopy analysis, and adopted two different geometries, that is, trigonal planar preferably for Cu^I and tetrahedral preferably for Cu^II. The as-synthesized covellite CuS behaves as an efficient electro(pre)catalyst for alkaline water oxidation while deposited on a glassy carbon and nickel foam (NF) electrodes. Under cyclic voltammetry cycles, covellite CuS electrochemically and irreversibly oxidized to CuO, indicated by a redox feature at 1.2 V (vs the reversible hydrogen electrode) and an ex situ Raman study. Electrochemically activated covellite CuS to the CuO phase (termed as CuS_EA) behaves as a pure copper-based catalyst showing an overpotential (η) of only 349 (±5) mV at a current density of 20 mA cm^-2, and the TOF value obtained at η₃₄₉ (at 349 mV) is 1.1 × 10^-3 s^-1. A low R_ct of 5.90 Ω and a moderate Tafel slope of 82 mV dec^-1 confirm the fair activity of the CuS_EA catalyst compared to the CuS precatalyst, reference CuO, and other reported copper catalysts. Notably, the CuS_EA/NF anode can deliver a constant current of ca. 15 mA cm^-2 over a period of 10 h and even a high current density of 100 mA cm^-2 for 1 h. Post-oxygen evolution reaction (OER)-chronoamperometric characterization of the anode via several spectroscopic and microscopic tools firmly establishes the formation of crystalline CuO as the active material along with some amorphous Cu(OH)₂ via bulk reconstruction of the covellite CuS under electrochemical conditions. Given the promising OER activity, the CuS_EA/NF anode can be fabricated as a water electrolyzer, Pt(-)//(+)CuS_EA/NF, that delivers a j of 10 mA cm^-2 at a cell potential of 1.58 V. The same electrolyzer can further be used for electrochemical transformation of organic feedstocks like ethanol, furfural, and 5-hydroxymethylfurfural to their respective acids. The present study showcases that a highly active CuO/Cu(OH)₂ heterostructure can be constructed in situ on NF from the covellite CuS nanoplate, which is not only a superior pure copper-based electrocatalyst active for OER and overall water splitting but also for the electro-oxidation of industrial feedstocks.

Interface Dynamics in Ag-Cu3P Nanoparticle Heterostructures

Earth-abundant transition metal phosphides are promising materials for energy-related applications. Specifically, copper(I) phosphide is such a material and shows excellent photocatalytic activity. Currently, there are substantial research efforts to synthesize well-defined metal-semiconductor nanoparticle heterostructures to enhance the photocatalytic performance by an efficient separation of charge carriers. The involved crystal facets and heterointerfaces have a major impact on the efficiency of a heterostructured photocatalyst, which points out the importance of synthesizing potential photocatalysts in a controlled manner and characterizing their structural and morphological properties in detail. In this study, we investigated the interface dynamics occurring around the synthesis of Ag-Cu3P nanoparticle heterostructures by a chemical reaction between Ag-Cu nanoparticle heterostructures and phosphine in an environmental transmission electron microscope. The major product of the Cu-Cu3P phase transformation using Ag-Cu nanoparticle heterostructures with a defined interface as a template preserved the initially present Ag{111} facet of the heterointerface. After the complete transformation, corner truncation of the faceted Cu3P phase led to a physical transformation of the nanoparticle heterostructure. In some cases, the structural rearrangement toward an energetically more favorable heterointerface has been observed and analyzed in detail at the atomic level. The herein-reported results will help better understand dynamic processes in Ag-Cu3P nanoparticle heterostructures and enable facet-engineered surface and heterointerface design to tailor their physical properties.

Free-standing Co/Zn sulfide supported on Cu-foam for efficient overall water splitting

High-performance bifunctional electrocatalyst for both the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is arousing great interest aiming at efficient electrochemical splitting of water. Herein, we report a...

Highly selective electrochemical nitrate reduction using copper phosphide self-supported copper foam electrode: Performance, mechanism, and application

A highly active and selective electrode is essential in electrochemical denitrification. Although the emerging Cu-based electrode has attracted intensive attentions in electrochemical NO₃^- reduction, the issues such as restricted activity and selectivity are still unresolved. In our work, a binder-free composite electrode (Cu₃P/CF) was first prepared by direct growth of copper phosphide on copper foam and then applied to electrochemical NO₃^- reduction. The resulting Cu₃P/CF electrode showed enhanced electrochemical performance for NO₃^- reduction (84.3%) with high N₂ selectivity (98.01%) under the initial conditions of 1500 mg L^-1 Cl^- and 50 mg N L^-1 NO₃^-. The cyclic voltammetry (CV) and electrochemical impedance spectra (EIS) demonstrated that electrochemical NO₃^- reduction was achieved through electron transfer between NO₃^- and Cu⁰ originated from CF. The in-situ grown Cu₃P served as the bifunctional catalyst, the electron mediator or bridge to facilitate the electron-transfer for NO₃^- reduction and the stable catalyst to produce atomic H* toward NO₂^- conversion. Meanwhile, the Cu₃P/CF remained its electrocatalytic activity even after eight cyclic experiments. Finally, a 2-stage treatment strategy, pre-oxidation by Ir-Ru/Ti anode and post-reduction by Cu₃P/CF cathode, was designed for electrochemical chemical oxygen demand (COD) and total nitrogen (TN) removal from real wastewater.

Highly Crystalline Hollow Toroidal Copper Phosphosulfide via Anion Exchange: A Versatile Cation Exchange Nanoplatform

Postmodification of nanocrystals through cation exchange has been very successful in diversifying nanomaterial compositions while retaining the structural motif. Copper compound nanoparticles are particularly useful as templates because of inherent defects serving as effective cation diffusion routes and excellent cation mobility. Therefore, the development of shape-controlled multianion systems, such as copper phosphosulfide, can potentially lead to the formation of diverse metal phosphosulfide nanomaterials that have otherwise inaccessible compositions and structures. However, there is, to the best of our knowledge, no report on the shape-controlled synthesis of copper phosphosulfide nanoparticles because the introduction of the second anion to the metal compound might destroy the nanoparticle morphology and crystallinity due to the required high energy for anion diffusion and mixing. Herein, we report that it is feasible to transfer the structural motif of copper sulfide to copper phosphosulfide using tris(diethylamino)phosphine. The anion-mixed copper phosphosulfide in the form of a hollow toroid could provide a pathway to previously inaccessible phases and morphologies. We verified the versatility of a copper phosphosulfide hollow toroid as a cation-exchange template by the successful synthesis of cobalt, nickel, indium, and cadmium phosphosulfides as well as bimetallic cobalt-nickel phosphosulfide (Co_2-xNi_xP_1-yS_y) with a retained structural motif.

A combined experimental and theoretical approach revealing a direct mechanism for bifunctional water splitting on doped copper phosphide

A cost-effective electrocatalyst should have a high dispersion of active atoms and a controllable surface structure to optimize activity. Additionally, bifunctional characteristics give an added benefit for the overall water splitting. Herein, we report the synthesis and fabrication of Fe-doped Cu/Cu₃P supported on a flexible carbon cloth (CC) with a hydrophilic surface for efficient bifunctional water electrolysis under alkaline conditions. Surface doping of Fe in the hexagonal Cu₃P does not alter the lattice parameters, but it promotes the surface metallicity by stimulating Cu^δ+ and Cu⁰ sites in Cu₃P, resulting in an augmented electroactive surface area. Cu_2.75Fe_0.25P composition exhibits unprecedented OER activity with a low overpotential of 470 mV at 100 mA cm^-2. Under a two electrode electrolyzer system the oxygen and hydrogen gas was evolved with an unprecedented rate at their respective electrode made of same catalyst. Density functional theory further elucidates the role of the Fe center toward electronic state modulation, which eventually alters the entire adsorption behavior of the reaction intermediates and reduces the overpotential on Fe-doped system over pristine Cu₃P.

Crystalline Copper Selenide as a Reliable Non-Noble Electro(pre)catalyst for Overall Water Splitting

Electrochemical water splitting remains a frontier research topic in the quest to develop artificial photosynthetic systems by using noble metal-free and sustainable catalysts. Herein, a highly crystalline CuSe has been employed as active electrodes for overall water splitting (OWS) in alkaline media. The pure-phase klockmannite CuSe deposited on highly conducting nickel foam (NF) electrodes by electrophoretic deposition (EPD) displayed an overpotential of merely 297 mV for the reaction of oxygen evolution (OER) at a current density of 10 mA cm-2 whereas an overpotential of 162 mV was attained for the hydrogen evolution reaction (HER) at the same current density, superseding the Cu-based as well as the state-of-the-art RuO2 and IrO2 catalysts. The bifunctional behavior of the catalyst has successfully been utilized to fabricate an overall water-splitting device, which exhibits a low cell voltage (1.68 V) with long-term stability. Post-catalytic analyses of the catalyst by ex-situ microscopic, spectroscopic, and analytical methods confirm that under both OER and HER conditions, the crystalline and conductive CuSe behaves as an electro(pre)catalyst forming a highly reactive in situ crystalline Cu(OH)2 overlayer (electro(post)catalyst), which facilitates oxygen (O2 ) evolution, and an amorphous Cu(OH)2 /CuOx active surface for hydrogen (H2 ) evolution. The present study demonstrates a distinct approach to produce highly active copper-based catalysts starting from copper chalcogenides and could be used as a basis to enhance the performance in durable bifunctional overall water splitting.

Synthesis and Electrocatalytic HER Studies of Carbene-Ligated Cu3-xP Nanocrystals

N-heterocyclic carbenes (NHCs) are an important class of ligands capable of making strong carbon-metal bonds. Recently, there has been a growing interest in the study of carbene-ligated nanocrystals, primarily coinage metal nanocrystals, which have found application as catalysts for numerous reactions. The general ability of NHC ligands to positively affect the catalytic properties of other types of nanocrystal catalysts remains unknown. Herein, we present the first carbene-stabilized Cu_3-xP nanocrystals. Inquiries into the mechanism of formation of NHC-ligated Cu_3-xP nanocrystals suggest that crystalline Cu_3-xP forms directly as a result of a high-temperature metathesis reaction between a tris(trimethylsilyl)phosphine precursor and an NHC-CuBr precursor, the latter of which behaves as a source of both the carbene ligand and Cu⁺. To study the effect of the NHC surface ligands on the catalytic performance, we tested the electrocatalytic hydrogen evolving ability of the NHC-ligated Cu_3-xP nanocrystals and found that they possess superior activity to analogous oleylamine-ligated Cu_3-xP nanocrystals. Density functional theory calculations suggest that the NHC ligands minimize unfavorable electrostatic interactions between the copper phosphide surface and H⁺ during the first step of the hydrogen evolution reaction, which contributes to the superior performance of NHC-ligated Cu_3-xP catalysts as compared to oleylamine-ligated Cu_3-xP catalysts.

Ultra-high energy density supercapacitors based on metal-organic framework derived yolk-shell Cu-Co-P hollow nanospheres and CuFeS2 nanosheet arrays

Owing to the increased requirement for efficient energy storage systems (ESs), investigating favorable electrodes with porous nanoarchitecture for supercapacitors (SCs) is vital. Nonetheless, the development of these kinds of electrodes to obtain high energy density remains a difficult task. Low specific capacitances of positive (cathode) and negative (anode) electrode materials are a serious obstacle that limits the performance of asymmetric SCs (ASCs). Herein, we proposed the preparation of yolk-shell Cu-Co-P hollow nanospheres (Y-CCP HN) as a positive electrode using a metal-organic framework (MOF) and CuFeS₂ nanosheet (CFS NS) arrays as a negative electrode via a low-cost and simple hydrothermal route for ASCs. The Y-CCP HN and CFS NS electrodes exhibited significant specific capacitances (∼2043.3 F g^-1 (340.55 mA h g^-1) and 654.3 F g^-1 (218.1 mA h g^-1), respectively), considerable rate performances (∼77.55% and 63.2%, respectively, even at 24 A g^-1), and exceptional durability (96.7% and 95.3% after 8000 cycles, respectively). Most notably, the Y-CCP HN//CFS device delivers a wonderful energy density of 158.4 W h kg^-1 at a power density of 900.3 W kg^-1, a notable specific capacitance of 352.1 F g^-1 (176.05 mA h g^-1), and excellent cyclability (96.1% after 8000 cycles). This exploration demonstrates a good strategy for the construction of other metal phosphides and sulfides with porous nature, emphasizing considerable prospects for next-generation ESs.

A rational design of nanoporous Cu–Co–Ni–P nanotube arrays and CoFe2Se4 nanosheet arrays for flexible solid-state asymmetric devices

A facile method was developed to synthesize nanoporous Cu–Co–Ni–P nanotube arrays and hierarchical CoFe₂Se₄ nanosheet arrays for a flexible asymmetric device.

A Simple and Scalable Approach To Remarkably Boost the Overall Water Splitting Activity of Stainless Steel Electrocatalysts

The stainless steel mesh (SSM) has received growing consideration as an electrocatalyst for efficient hydrogen and oxygen evolution reactions. Recently, the application of SSM as an oxygen evolution reaction (OER) electrocatalyst has been more promising, while its hydrogen evolution reaction (HER) catalytic activity is very low, which definitely affects its overall water splitting activity. Herein, a simple chemical bath deposition (CBD) method followed by phosphorization is employed to significantly boost the overall water splitting performance of SSM. The CBD method could allow the voids between the SSM fibers to be filled with Ni and P. Electrocatalytic studies show that the CBD-treated and phosphorized stainless steel (denoted SSM-Ni-P) exhibits an HER overpotential of 149 mV, while the phosphorization-free CBD-treated SSM (denoted as SSM-Ni) delivers an OER overpotential of 223 mV, both at a current density of 10 mA cm^-2. An asymmetric alkaline electrolyzer assembled based on the SSM-Ni-P cathode (HER) and SSM-Ni anode (OER) achieved an onset and 10 mA cm^-2 current densities at an overall potential of 1.62 V, granting more prospects for the application of inexpensive and highly active electrocatalysts for electrocatalytic water splitting reactions.

In pursuit of advanced materials from single-source precursors based on metal carbonyls

In this perspective, the development of single-source precursors and their relative advantages over multiple source approaches for the synthesis of metal pnictide solid state materials is explored. Particular efforts in the selective production of iron phosphide materials for catalytic applications are discussed, especially directed towards the hydrogen evolution and oxygen evolution reactions of water splitting.

The oxygen evolution reaction enabled by transition metal phosphide and chalcogenide pre-catalysts with dynamic changes

Dynamic morphological, structural and compositional changes will occur when transition metal phosphides and chalcogenides are used to catalyze the oxygen evolution reaction, which can substantially enhance their electrocatalytic performance.

Nanoporous Sulfur-Doped Copper Oxide (Cu2OxS1-x) for Overall Water Splitting

Developing active and bifunctional noble metal-free electrocatalysts is crucial for both the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in the full water splitting process. A ternary nanoporous sulfur-doped copper oxide (Cu₂O_xS_1-x) was successfully synthesized on Cu foam. The obtained Cu₂O_xS_1-x/Cu shows robust electrocatalytic activity toward HER with a low overpotential of 40 mV at 10 mA cm^-2 and a Tafel slope of 68 mV dec^-1 and exhibits long-term stability in acid solution. Moreover, Cu₂O_xS_1-x shows excellent electrocatalytic activity for OER, HER, and overall water splitting as a bifunctional catalyst in 1.0 M KOH electrolyte. The sulfur doping strategy implemented here can greatly improve the catalytic performance and stability in both acidic and alkaline water electrolyzers and presents an efficient catalyst for overall water splitting.

Ni(OH)2–Fe2P hybrid nanoarray for alkaline hydrogen evolution reaction with superior activity

Ni(OH)₂–Fe₂P nanoarray on Ti mesh (Ni(OH)₂–Fe₂P/TM) acts as a superior electrocatalyst for hydrogen evolution reaction, requiring an overpotential of 76 mV to drive 10 mA cm⁻² in 1.0 M KOH.

Efficient oxygen evolution electrocatalyzed by a Cu nanoparticle-embedded N-doped carbon nanowire array

A Cu nanoparticle-embedded N-doped carbon nanowire array on copper foam (Cu–N–C NA/CF) shows high catalytic activity, needing an overpotential of 314 mV to drive a geometrical current density of 20 mA cm⁻² in 1.0 M KOH.

Theoretical insights into the effective hydrogen evolution on Cu3P and its evident improvement by surface-doped Ni atoms

Deep understanding at the atomic level of the HER catalytic activity of Cu₃P and its significant enhancement by surface-doped Ni atoms.

Electroactive Polyhydroquinone Coatings for Marine Fouling Prevention-A Rejected Dynamic pH Hypothesis and a Deceiving Artifact in Electrochemical Antifouling Testing

Nanometer-thin coatings of polyhydroquinone (PHQ), which release and absorb protons upon oxidation and reduction, respectively, were tested for electrochemically induced anti-biofouling activity under the hypothesis that a dynamic pH environment would discourage fouling. Antifouling tests in artificial seawater using the marine, biofilm-forming bacterium Vibrio alginolyticus proved the coatings to be ineffective in fouling prevention but revealed a deceiving artifact from the reactive species generated at the counter electrode (CE), even for electrochemical bias potentials as low as |400| mV versus Ag|AgCl. These findings provide valuable information on the preparation of nanothin PHQ coatings and their electrochemical behavior in artificial seawater. The results further demonstrate that it is critical to isolate the CE in electrochemical anti-biofouling testing.