Colloids of Naked CH3NH3PbBr3 Perovskite Nanoparticles: Synthesis, Stability, and Thin Solid Film Deposition

Light-enhanced oxygen degradation of MAPbBr3 single crystal

Organometal halide perovskites are promising materials for optoelectronic applications, whose commercial realization depends critically on their stability under multiple environmental factors. In this study, a methylammonium lead bromide (MAPbBr3) single crystal was cleaved and exposed to simultaneous oxygen and light illumination under ultrahigh vacuum (UHV). The exposure process was monitored using X-ray photoelectron spectroscopy (XPS) with precise control of the exposure time and oxygen pressure. It was found that the combination of oxygen and light accelerated the degradation of MAPbBr3, which could not be viewed as a simple addition of that by oxygen-only and light-only exposures. The XPS spectra showed significant loss of carbon, bromine, and nitrogen at an oxygen exposure of 1010 Langmuir with light illumination, approximately 17 times of the additive effects of oxygen-only and light-only exposures. It was also found that the photoluminescence (PL) emission was much weakened by oxygen and light co-exposure, while previous reports had shown that PL was substantially enhanced by oxygen-only exposure. Measurements using a scanning electron microscope (SEM) and focused ion beam (FIB) demonstrated that the crystal surface was much roughened by the co-exposure. Density functional theory (DFT) calculations revealed the formation of superoxide and oxygen induced gap state, suggesting the creation of oxygen radicals by light illumination as a possible microscopic driving force for enhanced degradation.

In Situ Tetraalkylammonium Ligand Engineering of Organic-Inorganic Hybrid Perovskite Nanoparticles for Enhancing Long-Term Stability and Optical Tunability

Organic-inorganic hybrid perovskite nanoparticles (OIHP NPs) have attracted scientific attention owing to their efficient photoluminescence with optical tunability, which is highly advantageous for optoelectronic applications. However, the limited long-term stability of OIHP NPs has significantly hindered their practical application. Despite several synthetic strategies and encapsulation methods to stabilize OIHP NPs, complicated multi-step procedures are often required. In this study, we introduce an in situ ligand engineering method for stabilizing and controlling the optical properties of OIHP NPs using tetraalkylammonium (TAA) halides with various molecular structures at different concentrations. Our one-pot ligand engineering substantially enhanced the stability of the OIHP NPs without post-synthetic processes. Moreover, in certain cases, approximately 90% of the initial photoluminescence (PL) intensity was preserved even after a month under ambient conditions (room temperature, 20-50% relative humidity). To determine the role of ligand engineering in stabilizing the OIHP NPs, the surface binding properties of the TAA ligands were thoroughly analyzed using Raman spectroscopy. Specifically, the permanent positive charge of the TAA cations and consequent effective electrostatic interactions with the surfaces of the OIHP NPs are pivotal for preserving the initial PL intensity. Our investigation is beneficial for developing OIHP nanomaterials with improved stability and controlled photoluminescence for various optoelectronic applications, such as light-emitting devices, photosensitizers, photodetectors, photocatalysis, and solar cells.

Cyan Emission in Two-Dimensional Colloidal Cs2CdCl4:Sb3+ Ruddlesden-Popper Phase Nanoplatelets

Metal halide perovskites are one of the most investigated materials in optoelectronics, with their lead-based counterparts being renowned for their enhanced optoelectronic performance. The 3D CsPbX₃ structure has set the standard with many studies currently attempting to substitute lead with other metals while retaining the properties of this material. This effort has led to the fabrication of metal halides with lower dimensionality, wherein particular 2D layered perovskite structures have captured attention as inspiration for the next generation of colloidal semiconductors. Here we report the synthesis of the Ruddlesden-Popper Cs₂CdCl₄:Sb³⁺ phase as colloidal nanoplatelets (NPs) using a facile hot injection approach under atmospheric conditions. Through strict adjustment of the synthesis parameters with emphasis on the ligand ratio, we obtained NPs with a relatively uniform size and good morphological control. The particles were characterized through transmission electron microscopy, synchrotron X-ray diffraction, and pair distribution function analysis. The spectroscopic characterization revealed most strikingly an intense cyan emission under UV excitation with a measured PLQY of ∼20%. The emission was attributed to the Sb³⁺-doping within the structure.

Ruddlesden-Popper Hybrid Lead Bromide Perovskite Nanosheets of Phase Pure n=2: Stabilized Colloids Stored in the Solid State

Ruddlesden‐Popper lead halide perovskite (RP‐LHP) nano‐nanostructures can be regarded as self‐assembled quantum wells or superlattices of 3D perovskites with an intrinsic quantum well thickness of a single or a few (n=2‐4) lead halide layers; the quantum wells are separated by organic layers. They can be scaled down to a single quantum well dimension. Here, the preparation of highly (photo)chemical and colloidal stable hybrid LHP nanosheets (NSs) of ca. 7.4 μm lateral size and 2.5 nm quantum well height (thereby presenting a deep blue emission at ca. 440 nm), is reported for the first time. The NSs are close‐lying and they even interconnect when deposited on a substrate. Their synthesis is based on the use of the p‐toluenesulfonic acid/dodecylamine (pTS/DDA) ligand pair and their (photo)chemical stability and photoluminescence is enhanced by adding EuBr₂ nanodots (EuNDs). Strikingly, they can be preserved as a solid and stored for at least one year. The blue emissive colloid can be recovered from the solid as needed by simply dispersing the powder in toluene and then using it to prepare solid films, making them very promising candidates for manufacturing devices.

Defect Passivation in Lead-Halide Perovskite Nanocrystals and Thin Films: Toward Efficient LEDs and Solar Cells

Lead-halide perovskites (LHPs), in the form of both colloidal nanocrystals (NCs) and thin films, have emerged over the past decade as leading candidates for next-generation, efficient light-emitting diodes (LEDs) and solar cells. Owing to their high photoluminescence quantum yields (PLQYs), LHPs efficiently convert injected charge carriers into light and vice versa. However, despite the defect-tolerance of LHPs, defects at the surface of colloidal NCs and grain boundaries in thin films play a critical role in charge-carrier transport and nonradiative recombination, which lowers the PLQYs, device efficiency, and stability. Therefore, understanding the defects that play a key role in limiting performance, and developing effective passivation routes are critical for achieving advances in performance. This Review presents the current understanding of defects in halide perovskites and their influence on the optical and charge-carrier transport properties. Passivation strategies toward improving the efficiencies of perovskite-based LEDs and solar cells are also discussed.

Optical Properties and First-Principles Study of CH3NH3PbBr3 Perovskite Structures

Solution-processed organic-inorganic hybrid perovskites have attracted attention as light-harvesting materials for solar cells and photonic applications. The present study focuses on cubic single crystals and microstructures of CH₃NH₃PbBr₃ perovskite fabricated by a one-step solution-based self-assembly method. It is seen that, in addition to the nucleation from the precursor solution, crystallization occurs when the solution is supersaturated, followed by the formation of a small nucleus of CH₃NH₃PbBr₃ that self-assembles into bigger hollow cubes. A three-dimensional (3D) fluorescence microscopy investigation of hollow cubes confirmed the formation of hollow plates on the bottom; then, the growth starts from the perimeter and propagates to the center of the cube. Furthermore, the growth in the (001) direction follows a layer-by-layer growth model to form a complete cube, confirmed by scanning electronic microscopy (SEM) observations. Two-dimensional (2D)-3D fluorescence microscopy and photoluminescence (PL) measurements confirm a peak emission at 535 nm. To get more insights into the structural and optical properties, density functional theory (DFT) simulations were conducted. The electronic and optical properties calculated by DFT are in agreement with the obtained experimental values. The density-of-state (DOS) calculations revealed that the valence band maximum (VBM) consists of states contributed by Br and Pb, which agrees with the X-ray photoelectron spectroscopy valence band (XPS VB) measurements.

Study on the Ultrafast Process of Perovskite Nanoparticles Modified by Different Alkyl Chains

Three kinds of perovskite nanoparticles encapsulated with different chain lengths of alkylammonium, (CH₃NH₃)_x(CH₃(CH₂)₃NH₃)_(1-x)PbBr₃ (NP-C₄), (CH₃NH₃)_x(CH₃(CH₂)₇NH₃)_(1-x)PbBr₃ (NP-C₈), and (CH₃NH₃)_x(CH₃(CH₂)₁₁NH₃)_(1-x)PbBr₃ (NP-C₁₂), are successfully prepared. X-ray powder diffraction experiments demonstrate that these three nanoparticles are all pure cubic phase. However, the compositions of these three nanoparticles are significantly different, as revealed by steady-state absorption spectra. NP-C₄ mainly consists of 2D perovskite with m (number of unit cell layers) = 1 and 3D perovskite. Instead, NP-C₈ and NP-C₁₂ are mainly composed of 2D perovskite with m = 3, 4, and 5. Time-resolved fluorescence spectra and femtosecond transient absorption spectra suggest the presence of energy transfer from 2D perovskite to 3D perovskite in these three nanoparticles. More importantly, the energy-transfer rate gradually decreases from NP-C₄ to NP-C₁₂. This result suggests that the composition of perovskite nanoparticles and their corresponding photophysical properties can be controlled by the chain length of alkylammonium. This provides a new insight for preparing novel perovskite nanoparticles for special applications.

The synergy between the CsPbBr3 nanoparticle surface and the organic ligand becomes manifest in a demanding carbon–carbon coupling reaction

The cooperative action between the CsPbBr₃ surface and capping makes the photoredox homo-/cross-coupling of benzyl bromides under mild conditions possible.

Ultrathin lead bromide perovskite platelets spotted with europium(ii) bromide dots

We describe here the preparation of a novel nanohybrid comprising a two-layer cesium lead bromide nanoplatelet, [CsPbBr3]PbBr4 NPL, containing europium(ii) bromide (EuBr2) nanodots, by ultrasound/heating treatment of toluene dispersions of the CsPbBr3 nanomaterial in the presence of EuBr2 nanodots. The hybrid nanoplatelets exhibit strong excitonic and narrow emission peaks characteristic of ultrathin NPLs at 430 and 436 nm, respectively.

Colloidal Synthesis of Double Perovskite Cs2AgInCl6 and Mn-Doped Cs2AgInCl6 Nanocrystals

We show here the first colloidal synthesis of double perovskite Cs₂AgInCl₆ nanocrystals (NCs) with a control over their size distribution. In our approach, metal carboxylate precursors and ligands (oleylamine and oleic acid) are dissolved in diphenyl ether and reacted at 105 °C with benzoyl chloride. The resulting Cs₂AgInCl₆ NCs exhibit the expected double perovskite crystal structure, are stable under air, and show a broad spectrum white photoluminescence (PL) with quantum yield of ∼1.6 ± 1%. The optical properties of these NCs were improved by synthesizing Mn-doped Cs₂AgInCl₆ NCs through the simple addition of Mn-acetate to the reaction mixture. The NC products were characterized by the same double perovskite crystal structure, and Mn doping levels up to 1.5%, as confirmed by elemental analyses. The effective incorporation of Mn ions inside Cs₂AgInCl₆ NCs was also proved by means of electron spin resonance spectroscopy. A bright orange emission characterized our Mn-doped Cs₂AgInCl₆ NCs with a PL quantum yield as high as ∼16 ± 4%.

Electronic Properties of Free-Standing Surfactant-Capped Lead Halide Perovskite Nanocrystals Isolated in Vacuo

We report an investigation of lead halide perovskite CH₃NH₃PbBr₃ nanocrystals and associated ligand molecules by combining several different state-of-the-art experimental techniques, including synchrotron radiation-based XPS and VUV PES of free-standing nanocrystals isolated in vacuum. By using this novel approach for perovskite materials, we could directly obtain complete band alignment to vacuum of both CH₃NH₃PbBr₃ nanocrystals and the ligands widely used in their preparation. We discuss the possible influence of the ligand molecules to apparent perovskite properties, and we compare the electronic properties of nanocrystals to those of bulk material. The experimental results were supported by DFT calculations.