Engineering the Self-Assembly Induced Emission of Copper Nanoclusters as 3D Nanomaterials with Mesoporous Sphere Structures by the Crosslinking of Ce3

Innovative enhancement of electron tunneling synergy in carbon-doped Ta2O5CuO photocatalyst with nematic liquid crystal for safe drinking water

This study focuses on enhancing the photocatalytic properties of carbon-doped Ta2O5CuO (C-Ta2O5CuO) nanocomposites for drinking water purification. The nanocomposites were fabricated by depositing C-Ta2O5CuO onto Nematic Liquid Crystal Polaroid (NLCP) obtained from a discarded laptop monitor, employing the sputter deposition method. The X-ray diffraction (XRD) and High-resolution transmission electron microscopy (HRTEM) determined the nanocomposite thin films' crystallinity and structural properties. The EDX and XPS analyses confirmed the elemental composition and reality of the Cu-incorporated Ta2O5 nanocomposites, respectively. The combination of electron tunneling enhancement provided by the NLCP and graphitic carbon led to exceptional photocatalytic performance. This was particularly evident in the efficient degradation of P-Rosaniline Hydrochloride (PRH) dye in an aqueous medium. C-Ta2O5CuO catalytic activities were estimated at various dye concentrations, repeatability, reusability with time, and kinetics. Coating's stability and long-term activity in photocatalysis reactions were also tested. Additionally, Cu present in the C-Ta2O5CuO and ˙OH radicals exhibited remarkable bactericidal activity. They displayed significant antibacterial efficacy against both gram-positive Escherichia coli (E. coli) and gram-negative Staphylococcus aureus (S. aureus) bacteria. These findings have significant implications for the development of advanced materials with potent photocatalytic and antibacterial properties, holding promise for improving drinking water quality and addressing environmental and health challenges.

Liquid- liquid (Cyclohexanone: Cyclohexanol) separation using augmented tight nanofiltration membrane: A sustainable approach

Organic solvent nanofiltration (OSN) is an incipient technology in the field of organic liquid-liquid separation. The incomplete separations and complexity involved in these, forces many organic liquids to be released as effluents and the adverse effects of these on environment is enormous and irreparable. The work prominences on the complete separation of industrially significant cyclohexanone: cyclohexanol (keto-alcohol oil) and heptane: toluene mixtures. The separations of these above-mentioned organic liquid mixtures were carried out using the fabricated Lewis acid modified graphitic carbon nitride (Cu2O@g-C3N4) incorporated polyvinylidene difluoride (PVDF) composite membranes. These fabricated membranes showed a separation factor of 18.16 and flux of 1.62 Lm-2h-1 for cyclohexanone: cyclohexanol mixture and separation of heptane and toluene mixture (with heptane flux of 1.52 Lm-2h-1) showed a separation factor of 9.9. The selectivity and productivity are based on the polarity and size of the organic liquids. The role of Cu2O@g-C3N4 is influencing the pore size distribution, increased divergence from solubility parameters, polarity, solvent uptake and porosity of the composite membranes. The developed composite membranes are thus envisioned to be apt for a wide range of liquid-liquid separations due to its implicit nature.

Copper nanoparticles encapsulated in zeolitic imidazolate framework-8 as a stable and selective CO2 hydrogenation catalyst

Metal-organic frameworks have drawn attention as potential catalysts owing to their unique tunable surface chemistry and accessibility. However, their application in thermal catalysis has been limited because of their instability under harsh temperatures and pressures, such as the hydrogenation of CO2 to methanol. Herein, we use a controlled two-step method to synthesize finely dispersed Cu on a zeolitic imidazolate framework-8 (ZIF-8). This catalyst suffers a series of transformations during the CO2 hydrogenation to methanol, leading to ~14 nm Cu nanoparticles encapsulated on the Zn-based MOF that are highly active (2-fold higher methanol productivity than the commercial Cu-Zn-Al catalyst), very selective (>90%), and remarkably stable for over 150 h. In situ spectroscopy, density functional theory calculations, and kinetic results reveal the preferential adsorption sites, the preferential reaction pathways, and the reverse water gas shift reaction suppression over this catalyst. The developed material is robust, easy to synthesize, and active for CO2 utilization.

Triggering antibacterial activity of a common plant by biosorption of selected heavy metals

The presented study proposes an efficient utilization of a common Thymus serpyllum L. (wild thyme) plant as a highly potent biosorbent of Cu(II) and Pb(II) ions and the efficient interaction of the copper-laden plant with two opportunistic bacteria. Apart from biochars that are commonly used for adsorption, here we report the direct use of native plant, which is potentially interesting also for soil remediation. The highest adsorption capacity for Cu(II) and Pb(II) ions (qe = 12.66 and 53.13 mg g-1, respectively) was achieved after 10 and 30 min of adsorption, respectively. Moreover, the Cu-laden plant was shown to be an efficient antibacterial agent against the bacteria Escherichia coli and Staphylococcus aureus, the results being slightly better in the former case. Such an activity is enabled only via the interaction of the adsorbed ions effectively distributed within the biological matrix of the plant with bacterial cells. Thus, the sustainable resource can be used both for the treatment of wastewater and, after an effective embedment of metal ions, for the fight against microbes.

Ratiometric fluorescence determination of alkaline phosphatase activity based on carbon dots and Ce3+-crosslinked copper nanoclusters

A new ratiometric fluorescent probe for efficient determination of ALP was developed. The probe was constructed by combining Ce3+-crosslinked copper nanoclusters (Ce3+-CuNCs) which exhibit the aggregation-induced emission (AIE) feature with carbon dots (CDs). The introduction of phosphate (Pi) induced the generation of CePO4 precipitation, resulting in significant decrease of fluorescence emission of CuNCs at 634 nm. At the same time, the fluorescence of CDs at 455 nm was obviously enhanced, thus generating ratiometric fluorescence response. Based on the fact that the hydrolysis of pyrophosphate (PPi) by ALP can produce Pi, the CD/Ce3+-CuNCs ratiometric probe was successfully used to determine ALP. A good linear relationship between the ratiometric value of F455/F634 and ALP concentrations ranging from 0.2 to 80 U·L- 1 was obtained, with a low detection limit of 0.1 U·L- 1. The ratiometric responses of the probe resulted in the visible fluorescence color change from orange red to blue with the increase of ALP concentration. The smartphone-based RGB recognition of the fluorescent sample images was used for ALP quantitative determination. A novel ratiometric fluorescent system based on Ce3+-CuNCs with AIE feature and CDs were constructed for efficient detection of ALP.

Delamination of multilayer Ti3C2Tx MXene alters its adsorpiton and reduction of heavy metals in water

MXenes are considered as an emerging class of two-dimensional (2D) adsorbent for various environmental applications. In this work, two different morphologies of Ti₃C₂T_x MXene (multilayer (ML-Ti₃C₂T_x) and delaminated titanium carbide (DL-Ti₃C₂T_x)) were prepared through mild in situ HF etching and further delamination. The structural differences between the two were explored with a focus on their effects on the performance and mechanism of removing heavy metals from water. In comparison to ML-Ti₃C₂T_x, DL-Ti₃C₂T_x had more oxygen-containing functional groups, higher specific surface area (19.713 vs. 8.243 m²/g), larger pore volume (0.135 vs. 0.040 cm³/g), higher maximum Pb(II) adsorption capacity (77.0 vs. 56.68 mg/g), but lower maximum Cu(II) adsorption capacity (23.08 vs. 55.46 mg/g). Further investigation revealed that the removal of Pb(II) by the MXenes was mainly controlled through electrostatic attraction and surface complexation mechanisms, while Cu(II) was removed mainly through surface reduction by Ti-related groups. Because delamination of ML-Ti₃C₂T_x increased the surface area and surface functional groups, DL-Ti₃C₂T_x became a better sorbent for Pb(II) in water. During sonication, however, delamination inevitably led to partial oxidation of Ti₃C₂T_x nanosheets and thus weakened the reducing ability of DL-Ti₃C₂T_x for Cu(II) in water. Nevertheless, both ML- and DL-Ti₃C₂T_x not only exhibited excellent heavy metal adsorption capacity under different solution conditions, but also showed good reusability. Findings of this study indicate that Ti₃C₂T_x MXenes are promising adsorbents for treating heavy metal pollutants in water.

Formation and Transformation of Cu2-xSe1-yTey Nanoparticles Synthesized by Tellurium Anion Exchange of Copper Selenide

Ion exchange reactions of colloidal nanoparticles post-synthetically modify the composition while maintaining the morphology and crystal structure and therefore are important for tuning properties and producing otherwise inaccessible and/or metastable materials. Reactions involving anion exchange of metal chalcogenides are particularly interesting, as they involve the replacement of the sublattice that defines the structure while also requiring high temperatures that can be disruptive. Here, we show that the tellurium anion exchange of weissite Cu_2-xSe nanoparticles using a trioctylphosphine-tellurium complex (TOP═Te) yields weissite Cu_2-xSe_1-yTe_y solid solutions, rather than complete exchange to weissite Cu_2-xTe, with compositions that are tunable based on the amount of TOP═Te used. Upon storage at room temperature in either solvent or air, tellurium-rich Cu_2-xSe_1-yTe_y solid solution nanoparticles transform, over the span of several days, to a selenium-rich Cu_2-xSe_1-yTe_y composition. The tellurium that is expelled from the solid solution during this process migrates to the surface and forms a tellurium oxide shell, which correlates with the onset of particle agglomeration due to the change in surface chemistry. Collectively, this study demonstrates tunable composition during tellurium anion exchange of copper selenide nanoparticles along with unusual post-exchange reactivity that transforms the composition, surface chemistry, and colloidal dispersibility due to the apparent metastable nature of the solid solution product.

Steering carbon dioxide reduction toward C-C coupling using copper electrodes modified with porous molecular films

Copper offers unique capability as catalyst for multicarbon compounds production in the electrochemical carbon dioxide reduction reaction. In lieu of conventional catalysis alloying with other elements, copper can be modified with organic molecules to regulate product distribution. Here, we systematically study to which extent the carbon dioxide reduction is affected by film thickness and porosity. On a polycrystalline copper electrode, immobilization of porous bipyridine-based films of varying thicknesses is shown to result in almost an order of magnitude enhancement of the intrinsic current density pertaining to ethylene formation while multicarbon products selectivity increases from 9.7 to 61.9%. In contrast, the total current density remains mostly unaffected by the modification once it is normalized with respect to the electrochemical active surface area. Supported by a microkinetic model, we propose that porous and thick films increase both local carbon monoxide partial pressure and the carbon monoxide surface coverage by retaining in situ generated carbon monoxide. This reroutes the reaction pathway toward multicarbon products by enhancing carbon-carbon coupling. Our study highlights the significance of customizing the molecular film structure to improve the selectivity of copper catalysts for carbon dioxide reduction reaction.

Nanomaterial Gas Sensors for Biosensing Applications: A Review

BACKGROUND

Nanomaterial is one of the most used materials for various gas sensing applications to detect toxic gases, human breath, and other specific gas sensing. One of the most important applications of nanomaterial based gas sensors is biosensing applications. In this review article, the gas sensors for biosensing are discussed on the basis of crystalline structure and different categories of nanomaterial.

METHODS

In this paper, firstly, rigorous efforts have been made to find out research questions by going through a structured and systematic survey of available peer reviewed high quality articles in this field. The papers related to nanomaterial based biosensors are then reviewed qualitatively to provide substantive findings from the recent developments in this field.

RESULTS

In this mini-review article, firstly, classifications of nanomaterial gas sensors have been presented on the basis of the crystalline structure of nanomaterial and different types of nanomaterial available for biosensing applications. Further, the gas sensors based on nanomaterial for biosensing applications are collected and reviewed in terms of their performance parameters such as sensing material used, target gas component, detection ranges (ppm-ppb), response time, operating temperature and method of detection, etc. The different nanomaterials possess slightly different sensing and morphological properties due to their structure; therefore, it can be said that a nanomaterial must be selected carefully for a particular application. The 1D nanomaterials show the best selectivity and sensitivity for gases available in low concentration ranges due to their miniaturised structure compared to 2D and 3D nanomaterials. However, these 2D and 3D nanomaterials also so good sensing properties compared to bulk semiconductor materials. The polymer and nanocomposites which are also discussed in this patent article have opened the door for future research and have great potential for new generation gas sensors for detecting biomolecules.

CONCLUSION

These nanomaterials extend great properties towards sensing the application of different gases for a lower concentration of particular gas particles. Nano polymer and nanocomposites have great potential to be used as gas sensors for the detection of biomolecules.

Ce3+ and Fe2+ co-enhanced ratiometric fluorescence probe utilizing copper nanoclusters and coumarin for sensitive assay of hydrogen peroxide and glucose

A novel ratiometric fluorescent probe was constructed for sensitive assay of hydrogen peroxide (H₂O₂) and glucose, which utilized the synergistically enhanced effects of Ce³⁺ and Fe²⁺ on copper nanoclusters (CuNCs) and coumarin. In the CuNCs-Ce³⁺/Fe²⁺-coumarin system, Ce³⁺ triggered the aggregation-induced emission phenomenon of CuNCs, and Fe²⁺ catalyzed the Fenton reaction to efficiently yield hydroxyl radical (•OH). In the presence of H₂O₂, the 625-nm red fluorescence of CuNCs was sharply quenched owing to the oxidation of CuNCs to Cu(II) by •OH, but the 460-nm blue fluorescence of 7-hydroxycoumarin from the oxidation of coumarin by •OH dramatically increased. Based on the reversible changes in two fluorescence signals, a satisfactorily ratiometric probe was constructed for H₂O₂ assay with a detection limit (LOD) of 0.6 μM accompanied by a visual color variation from red to blue. For glucose assay, this ratiometric probe gave a linear range of 3.2-160 μM and LOD of 0.96 μM owing to the oxidization of glucose to yield H₂O₂ in the presence of glucose oxidase and O₂. Overall, the newly developed ratiometric probe shows a great prospect in real applications for visual assay of H₂O₂ and glucose by our naked eyes.

Cation Crosslinking-Induced Stable Copper Nanoclusters Powder as Latent Fingerprints Marker

Luminescent copper nanoclusters (Cu NCs) have shown great potential in light-emitting devices (LEDs), chemical sensing, catalysis and biological fields. However, their practical use has been restricted by poor stability, and study on the stability of Cu NCs solid powder along with the mechanism is absent. In this study, stablized Cu NCs powder was first obtained by cation crosslinking method. Compared with the powder synthesized by solvent precipitation method, the stability of Cu NCs powder crosslinked by ionic inducer Ce3+ was enhanced around 100-fold. The storage time when the fluorescence intensity decreased to 85% (T85) was improved from 2 h to 216 h, which is the longest so far. The results of characterizations indicated that the aggregation structure was formed by the binding of Ce3+ with the capping ligands of Cu NCs, which helped in obtaining Ce-Cu NCs powder from aggregate precipitation in solution. Furthermore, this compact structure could avoid the destruction of ambient moisture resulting in long-lasting fluorescence and almost unchanged physical form. This demonstrated that phosphor, with excellent characteristics of unsophisticated synthesis, easy preservation and stable fluorescence, showed great potential in light sources, display technology and especially in latent fingerprints visualization on different substrates for forensic science.

Low-dimensional nanomaterials for antibacterial applications

The excessive use of antibiotics has led to a rise in drug-resistant bacteria. These "superbugs" are continuously emerging and becoming increasingly harder to treat. As a result, new and effective treatment protocols that have minimal risks of generating drug-resistant bacteria are urgently required. Advanced nanomaterials are particularly promising due to their drug loading/releasing capabilities combined with their potential photodynamic/photothermal therapeutic properties. In this review, 0-dimensional, 1-dimensional, 2-dimensional, and 3-dimensional nanomaterial-based systems are comprehensively discussed for bacterial-based diagnostic and treatment applications. Since the use of these platforms as antibacterials is relatively new, this review will provide appropriate insight into their construction and applications. As such, we hope this review will inspire researchers to explore antibacterial-based nanomaterials with the aim of developing systems for clinical applications.

Biomass-Derived Activated Carbon-Supported Copper Catalyst: An Efficient Heterogeneous Magnetic Catalyst for Base-Free Chan-Lam Coupling and Oxidations

Development of heterogeneous catalysts from biomass-derived activated carbon is a challenging task. Biomass-derived activated carbon possesses a large specific surface area, highly porous structure, and good thermal/chemical stability. Magnetic copper catalysts based on biomass-derived activated carbon exhibited good catalytic activity in base-free Chan-Lam coupling and oxidations. Herein, biomass-derived activated carbon was prepared by the carbonization of neem dead leaves (abundant waste biomass) followed by chemical activation with KOH. Such a porous carbon material was used as a low cost and highly efficient support material for the preparation of inexpensive and environmentally benign magnetic catalysts [Cu@KF-C/MFe2O4, M = Co, Cu, Ni, and Zn]. In addition, KF modification was done to impart basic character to the catalyst that can perform C-N coupling under base-free conditions. Initially, Brunauer-Emmett-Teller (BET) analysis of the synthesized catalysts was carried out, which indicated that Cu@KF-C/CoFe2O4 possess more surface area as well as pore volume, and so accounting for the highest activity among the other synthesized catalysts. Further, X-ray photoelectron spectroscopy (XPS) analysis was performed, which inferred that Cu@KF-C/CoFe2O4 contains most of the copper in reduced form, i.e., Cu(0), which is the active species responsible for better catalytic activity toward Chan-Lam coupling reactions as well as oxidation of alcohols and hydrocarbons. The physiochemical properties of the most active catalyst, Cu@KF-C/CoFe2O4, was examined by BET, XPS, Fourier transform infrared Spectroscopy (FTIR), thermogravimetric analysis (TGA), field emission gun scanning electron microscopy (FEG-SEM), high-resolution transmission electron microscopy (HR-TEM), energy dispersive X-ray (EDX) mapping, energy dispersive X-ray (EDX), inductively coupled plasma atomic emission spectroscopy (ICP-AES), powder X-ray diffraction (XRD), and vibrating sample magnetometry (VSM). Moreover, Cu@KF-C/CoFe2O4 shows excellent stability as well as reusability and could be easily separated with the help of an external magnet.

Ultrasensitive molecularly imprinted fluorescence sensor for simultaneous determination of CA125 and CA15-3 in human serum and OVCAR-3 and MCF-7 cells lines using Cd and Ni nanoclusters as new emitters

In the clinical diagnosis of tumors, a single-marker immunoassay may lead to false results. Thus there is a need for an effective and valid method for the simultaneous measurement of multiple tumor markers. In this work, an efficient fluorescence immunosensor for the simultaneous measurement of CA125 and CA15-3 tumor markers was fabricated by utilizing the high selectivity of magnetic molecularly imprinted polymers (MMIPs) and the high sensitivity of a fluorescence (FL) method. Ni nanoclusters (Ni NCs) and noble Cd nanoclusters (Cd NCs) were introduced as efficient and economic emitters, and magnetic graphene oxide (GO-Fe₃O₄) was applied as a support material for surface molecularly imprinted polymers. Under the most favorable experimental conditions, the fluorescence intensity of the Cd NCs and Ni NCs gradually increased with increasing concentration of CA125 and CA15-3 antigens at a range of 0.0005-40 U mL^-1, respectively, with a limit of detection (LOD) of 50 μU mL^-1. The developed method had excellent properties including a broad linear range, good reproducibility, and simple operation for the clinical diagnosis of CA 125 and CA 15-3 tumor markers. This molecularly imprinted fluorescence sensor has the potential to be an effective clinical tool for the timely screening of breast cancer in human serum samples and OVCAR-3 and MCF-7 cell lines, and can be applied in clinical diagnostics.

Fluorescent and visual assay of H2O2 and glucose based on a highly sensitive copper nanoclusters-Ce(III) fluoroprobe

Herein, we synthesized and characterized glutathione-capped copper nanoclusters (CuNCs) using a convenient one-pot chemical reduction approach based on glutathione as capping and reducing agents. The Ce(III) induced aggregation-induced emission of CuNCs to form a CuNCs-Ce³⁺ fluoroprobe due to electrostatic and coordination interactions between Ce³⁺ and CuNCs. In contrast to CuNCs, the fluorescent intensities (FLs) of CuNCs-Ce³⁺ were enhanced by ~ 40-fold concomitant with 20-nm blue-shift of the maximum emission, and a 3.45-fold lengthening of the average fluorescent lifetime. The FLs of CuNCs-Ce³⁺ were selectively quenched at 650 nm by hydrogen peroxide (H₂O₂) via the redox reaction. Based on this phenomenon, the sensitive assay of H₂O₂ was realized, and the linear range spanned over the range of 14-140 μM. Notably, the visualization of the fluorescence quenched effect of H₂O₂ could be easily attained. Additionally, glucose could be specifically oxidized by glucose oxidase to produce H₂O₂, and thus the detection of glucose was achieved according to changes in the concentrations of H₂O₂. Under optimized conditions, the fluorescent assay of glucose based on the CuNCs-Ce³⁺ system offered the linear range of 8-48 μM with detection limit of 2.4 μM. Meanwhile, high selectivity of the as-constructed fluorescent assay allows the sensitive detection of H₂O₂ and glucose in real-world care products and human serum samples, showing a great application potential in their conventional monitoring.

Purification and separation of ultra-small metal nanoclusters

Metal nanoclusters (NCs) are ultra-small nanoparticles intermediate in size between small molecule complexes and nanoparticles. NCs with tunable surface functionality feature unique physical and chemical properties, however these properties are frequently compromised by the presence of undesired components such as excess ligands or mixtures of NCs. In a typical synthesis process, different NCs can be formed with varying numbers of metal atoms and/or ligands, and even NCs with the same number of metal atoms and ligands can have different spatial structures. The separation of pure NCs is important because different species have distinct optical and catalytic behavior. However, NCs can be difficult to purify or separate for a range of reasons. In this review, we discuss established and emerging approaches for NC purification/separation, with a focus on choosing the appropriate method depending on NC and application.

Self-Assembly of Metal Nanoclusters for Aggregation-Induced Emission

Aggregation-induced emission (AIE) is an intriguing strategy to enhance the luminescence of metal nanoclusters (NCs). However, the morphologies of aggregated NCs are often irregular and inhomogeneous, leading to instability and poor color purity of the aggregations, which greatly limit their further potential in optical applications. Inspired by self-assembly techniques, manipulating metal NCs into well-defined architectures has achieved success. The self-assembled metal NCs often exhibit enhancing emission stability and intensity compared to the individually or randomly aggregated ones. Meanwhile, the emission color of metal NCs becomes tunable. In this review, we summarize the synthetic strategies involved in self-assembly of metal NCs for the first time. For each synthetic strategy, we describe the self-assembly mechanisms involved and the dependence of optical properties on the self-assembly. Finally, we outline the current challenges to and perspectives on the development of this area.