Effect of Sodium Oleate Surfactant Concentration Grafted onto SiO2 Nanoparticles in Polymer Flooding Processes

Evaluation of the Thermal, Chemical, Mechanical, and Microbial Stability of New Nanohybrids Based on Carboxymethyl-Scleroglucan and Silica Nanoparticles for EOR Applications

Scleroglucan (SG) is resistant to harsh reservoir conditions such as high temperature, high shear stresses, and the presence of chemical substances. However, it is susceptible to biological degradation because bacteria use SG as a source of energy and carbon. All degradation effects lead to viscosity loss of the SG solutions, affecting their performance as an enhanced oil recovery (EOR) polymer. Recent studies have shown that nanoparticles (NPs) can mitigate these degradative effects. For this reason, the EOR performance of two new nanohybrids (NH-A and NH-B) based on carboxymethyl-scleroglucan and amino-functionalized silica nanoparticles was studied. The susceptibility of these products to chemical, mechanical, and thermal degradation was evaluated following standard procedures (API RP 63), and the microbial degradation was assessed under reservoir-relevant conditions (1311 ppm and 100 °C) using a bottle test system. The results showed that the chemical reactions for the nanohybrids obtained modified the SG triple helix configuration, impacting its viscosifying power. However, the nanohybrid solutions retained their viscosity during thermal, mechanical, and chemical degradation experiments due to the formation of a tridimensional network between the nanoparticles (NPs) and the SG. Also, NH-A and NH-B solutions exhibited bacterial control because of steric hindrances caused by nanoparticle modifications to SG. This prevents extracellular glucanases from recognizing the site of catalysis, limiting free glucose availability and generating cell death due to substrate depletion. This study provides insights into the performance of these nanohybrids and promotes their application in reservoirs with harsh conditions.

Numerical study of the mechanisms of nano-assisted foam flooding in porous media as an alternative to gas flooding

Oil reservoirs are nearing maturation, necessitating novel enhanced oil recovery (EOR) techniques to meet escalating global energy demands. This demand has spurred interest in reservoir production analysis and forecasting tools to enhance economic and technical efficiency. Accurate validation of these tools, known as simulators, using laboratory or field data is pivotal for precise reservoir productivity estimation. This study delves into the application of nanoparticles in foam flooding for mobility control to improve sweep efficiency. Foam generation can occur in-situ by simultaneous injection of surfactants and gas or through pre-generated foam injection into the reservoir. In this work, a series of systematic simulations were run to investigate how much injected fluids can reduce gas breakthrough while also increasing oil recovery. Subsequently, we analyzed the most effective optimization strategies, considering their economic limits. Our primary objective is to numerically model nanofoam flooding as an innovative EOR approach, synergizing foam flooding mechanisms with nanotechnology benefits. In this work, modeling of nanoparticles in foam liquid was represented by the interfacial properties provided to the injection fluid. Additionally, we simulated Water-Alternating-Gas (WAG) injection schemes across various cycles, comparing their outcomes. Our results showed that nanofoam injection achieved a higher recovery factor of at least 38% and 95% more than WAG and gas injections, respectively. The superior efficiency and productivity of foam injection compared to WAG and gas injection suggest an optimal EOR approach within the scope of our model. These simulated optimization techniques contribute to the future development of processes in this field.

Effects and applications of surfactants on the release, removal, fate, and transport of microplastics in aquatic ecosystem: a review

Microplastics (MPs) and surfactants (STs) are emerging pollutants in the environment. While many studies have focused on the interactions of STs with MPs, there has not been a comprehensive review focusing on the effect of STs on MPs in aquatic ecosystems. This review summarizes methods for removal of MPs from wastewater (e.g., filtration, flotation, coagulation/flocculation, adsorption, and oxidation-reduction) and the interactions and effects of STs with MPs (adsorption, co-adsorption, desorption, and toxicity). STs can modify MPs surface properties and influence their removal using different wastewater treatments, as well as the adsorption-desorption of both organic and inorganic chemicals. The concentration of STs is a crucial factor that impacts the removal or adsorption of pollutants onto MPs. At low concentrations, STs tend to facilitate MPs removal by flotation and enhance the adsorption of pollutants onto MPs. High ST concentrations, mainly above the critical micelle concentrations, cause MPs to become dispersed and difficult to remove from water while also reducing the adsorption of pollutants by MPs. Excess STs form emulsions with the pollutants, leading to electrostatic repulsion between MPs/STs and the pollutant/STs. As for the toxicity of MPs, the addition of STs to MPs shows complicated results, with some cases showing an increase in toxicity, some showing a decrease, and some showing no effect.

Treatment of Ruptured Wide-Necked Aneurysms using a Microcatheter Injectable Biomaterial

Ruptured wide-neck aneurysms (WNAs), especially in a setting of coagulopathy, are associated with significant morbidity and mortality. It is shown that by trapping a sub-millimeter clinical catheter inside the aneurysm sac using a flow diverter stent (FDS), instant hemostasis can be achieved by filling the aneurysm sac using a novel biomaterial, rescuing catastrophic bleeding in large-animal models. Multiple formulations of a biomaterial comprising gelatin, nanoclay (NC), and iohexol are developed, optimized, and extensively tested in vitro to select the lead candidate for further testing in vivo in murine, porcine, and canine models of WNAs, including in a subset with aneurysm rupture. The catheter-injectable and X-ray visible versions of the gel embolic agent (GEA) with the optimized mechanical properties outperform control groups, including a subset that receive a clinically used liquid embolic (Onyx, Medtronic), with and without aneurysm rupture. A combinatorial approach to ruptured WNAs with GEA and FDS may change the standard of medical practice and save lives.

In vitro release of aluminum from the geophagic clay "Chacco" in the Peruvian highlands: Chemical characterization and health risk assessment

In the altiplano zone of Latin America, "Chacco" is one of the clays widely consumed as part of geophagy. The objectives of the study were to chemically characterize "Chacco", determine the zero charge point, evaluate the release of aluminum in vitro, perform the kinetic study and evaluate the health risk. The results by ICP-OES showed that the elements with the highest concentration were Al, Ba, Ca, Fe, K, Mg, Mn, Na, Si, Sr, Ti and Zn. ATR-FTIR analysis showed the presence of Si-O (693 and 990 cm^-1), Al-O (790 cm^-1), Al-Al-OH bending vibration (912 cm^-1), Si-H bond stretching (2100 to 2500 cm^-1) and free -OH groups (3629 cm^-1). SEM-EDX results indicate that Al is one of the main constituents of "Chacco" (7.35 wt%). The pHzpc of "Chacco" was 6.83. In the dissolution profiles, the highest Al release occurred at pH 6.8 and in intestinal juice simulated with pseudo-second order dissolution kinetics. The EDI_Al and EWI_Al were 20.24 and 142.66 respectively, comparing EWI_Al with the PTWI established by JECFA (2 mg/kg bw), it is concluded that the weekly intake of "Chacco" represents an appreciable health risk. There are no reports of the carcinogenic factor of Al, so TR_Al was not calculated.

A rapid staged protocol for efficient recovery of microplastics from soil and sediment matrices based on hydrophobic separation

Microplastics (MPs) in soil and sediment (SS) matrices are emerging pollution hazards to ecosystems and humans. To mitigate MP pollution, suitable extractors and associated extracting solutions are required to efficiently separate MPs from SS matrices. In this study, we introduced a four-stage microplastic extractor (ME) device and investigated the fractional separation efficiencies of three extracting solutions (ultrapure water, saturated NaCl, and corn oil-in-NaCl) plus aeration, magnetic stirring, and electric stirring for three kinds of SS matrices (loam soil, sandy sediment, and muddy sediment) with four types of virgin MP pellets (acrylonitrile butadiene styrene (ABS), polycarbonate (PC), polypropylene, and polystyrene). In addition, fragments of these four types of post-consumer MPs were also tested by the ME device. The mean recovery efficiencies of these MPs in the three SS matrices were 88.3 %-100 %. Oil-in-NaCl further improved the recovery efficiencies for the denser ABS and PC up to 40 % based on NaCl extraction.

Development of a Novel Green Bio-Nanofluid from Sapindus Saponaria for Enhanced Oil Recovery Processes

The main objective of this study is to develop a novel green-nanofluid from Sapindus Saponaria for its application in enhanced oil recovery (EOR) processes. The bio-nanofluid is composed of a green active compound (AGC), bio-ethanol, and commercial surfactant (SB) at a low concentration. The AGC was obtained from soapberry “Sapindus Saponaria” using the alcoholic extraction method and characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and critical micellar concentration (CMC) to verify the content of saponins as active agents with surface-active behavior. Three types of silica-based nanoparticles were used and characterized by FTIR, TGA, and dynamic light scattering (DLS) analysis. Two commercial nanoparticles (SiO2-C1 and SiO2-C2) were evaluated, and a third one (SiO2-RH) was synthesized from rice husks as an ecological nanomaterial alternative. The performance of the adjusted systems was evaluated by capillary number (effective interfacial tension (σe), wettability and viscosity) and finally with coreflooding tests under reservoir conditions. The FTIR results confirm the presence of saponins in the AGC. In addition, according to the TGA, the AGC is stable under the reservoir temperature of interest. Regarding nanoparticles, siloxane and silanol groups were observed in all samples. For SiO2-C1 and SiO2-C2 samples, the weight loss was lower than 5% for temperatures up to 700 °C. Meanwhile, SiO2-RH had a weight loss of 12% at 800 °C, and 8% at reservoir temperature. Results show a decrease in the interfacial tension (IFT) of up to 83% of the tuned system with only 100 mg·L−1 of rice husk nanoparticles compared to the system without nanoparticles, reaching values of 1.60 × 10−1 mN·m−1. In the coreflooding test, increases of up to 13% of additional crude oil were obtained using the best bio-nanofluid. This work presents an excellent opportunity to include green alternatives to improve conventional techniques with added value during the injection of chemicals in chemical-enhanced oil recovery (CEOR) processes.

Design and Tuning of Nanofluids Applied to Chemical Enhanced Oil Recovery Based on the Surfactant-Nanoparticle-Brine Interaction: From Laboratory Experiments to Oil Field Application

The primary objective of this study is to develop a novel experimental nanofluid based on surfactant–nanoparticle–brine tuning, subsequently evaluate its performance in the laboratory under reservoir conditions, then upscale the design for a field trial of the nanotechnology-enhanced surfactant injection process. Two different mixtures of commercial anionic surfactants (SA and SB) were characterized by their critical micelle concentration (CMC), density, and Fourier transform infrared (FTIR) spectra. Two types of commercial nanoparticles (CNA and CNB) were utilized, and they were characterized by S_BET, FTIR spectra, hydrodynamic mean sizes (dp₅₀), isoelectric points (pH_IEP), and functional groups. The evaluation of both surfactant–nanoparticle systems demonstrated that the best performance was obtained with a total dissolved solid (TDS) of 0.75% with the SA surfactant and the CNA nanoparticles. A nanofluid formulation with 100 mg·L⁻¹ of CNA provided suitable interfacial tension (IFT) values between 0.18 and 0.15 mN·m⁻¹ for a surfactant dosage range of 750–1000 mg·L⁻¹. Results obtained from adsorption tests indicated that the surfactant adsorption on the rock would be reduced by at least 40% under static and dynamic conditions due to nanoparticle addition. Moreover, during core flooding tests, it was observed that the recovery factor was increased by 22% for the nanofluid usage in contrast with a 17% increase with only the use of the surfactant. These results are related to the estimated capillary number of 3 × 10⁻⁵, 3 × 10⁻⁴, and 5 × 10⁻⁴ for the brine, the surfactant, and the nanofluid, respectively, as well as to the reduction in the surfactant adsorption on the rock which enhances the efficiency of the process. The field trial application was performed with the same nanofluid formulation in the two different injection patterns of a Colombian oil field and represented the first application worldwide of nanoparticles/nanofluids in enhanced oil recovery (EOR) processes. The cumulative incremental oil production was nearly 30,035 Bbls for both injection patterns by May 19, 2020. The decline rate was estimated through an exponential model to be −0.104 month⁻¹ before the intervention, to −0.016 month⁻¹ after the nanofluid injection. The pilot was designed based on a production increment of 3.5%, which was successfully surpassed with this field test with an increment of 27.3%. This application is the first, worldwide, to demonstrate surfactant flooding assisted by nanotechnology in a chemical enhanced oil recovery (CEOR) process in a low interfacial tension region.

Development of Nanofluids for the Inhibition of Formation Damage Caused by Fines Migration: Effect of the interaction of Quaternary Amine (CTAB) and MgO Nanoparticles

Fines migration is a common problem in the oil and gas industry that causes a decrease in productivity. In this sense, the main objective of this study is to develop nanocomposites based on the interaction of quaternary amine (hexadecyltrimethylammonium bromide—CTAB) and MgO to enhance the capacity of retention of fine particles in the porous medium. MgO nanoparticles were synthesized by the sol–gel method using Mg(NO₃)₂·6H₂O as a precursor. Nanoparticles were characterized by dynamic light scattering (DLS), the point of zero charge (pH_pzc), thermogravimetric analysis, and Fourier transform infrared spectroscopy (FT-IR). Different nanoparticle sizes of 11.4, 42.8, and 86.2 nm were obtained, which were used for preparing two system nanofluids. These systems were evaluated in the inhibition of fines migration: in the system I MgO nanoparticles were dispersed in a CTAB-containing aqueous solution, and system II consists of a nanocomposite of CTAB adsorbed onto MgO nanoparticles. The fines retention tests were performed using Ottawa sand 20/40 packed beds and fine particles suspensions at concentrations of 0.2% in a mass fraction in deionized water. Individual and combined effects of nanoparticles and CTAB were evaluated in different treatment dosages. The analysis of the interactions between the CTAB and the MgO nanoparticles was carried out through batch-mode adsorption and desorption tests. The best treatment in the system I was selected according to the fines retention capacity and optimized through a simplex-centroid mixture design for mass fractions from 0.0% to 2.0% of both CTAB and MgO nanoparticles. This statistical analysis shows that the optimal concentration of these components is reached for a mass fraction of 0.73% of MgO nanoparticles and 0.74% in mass fraction of CTAB, where the retention capacity of the porous medium increases from 0.02 to 0.39 mg·L⁻¹. Based on the experimental results, the nanofluids combining both components showed higher retention of fines than the systems treated only with CTAB or with MgO nanoparticles, with efficiencies up to 400% higher in the system I and higher up to 600% in the system II. To evaluate the best performance treatment under reservoir conditions, there were developed core flooding tests at fixed overburden pressure of 34.5 MPa, pore pressure at 6.9 MPa and system temperature at 93 °C. Obtaining critical rate increases in 142.8%, and 144.4% for water and oil flow in the presence of the nanofluid. In this sense, this work offers a new alternative for the injection of nanocomposites as a treatment for the problem of fines migration to optimize the productivity of oil and gas wells.