Environmentally benign sol-gel antifouling and foul-releasing coatings

A review of experimental Assessment Processes of material resistance to marine and freshwater biofouling

Biofouling presents hazards to a variety of freshwater and marine underwater infrastructures and is one of the direct causes of species invasion. These negative impacts provide a unified goal for both industry practitioners and researchers: the development of novel antifouling materials to prevent the adhesion of biofouling. The prohibition of tributyltin (TBT) by the International Maritime Organization (IMO) in 2001 propelled the research and development of new antifouling materials. However, the evaluation process and framework for these materials remain incomplete and unsystematic. This mini-review starts with the classification and principles of new antifouling materials, discussing and summarizing the methods for assessing their biofouling resistance. The paper also compiles the relevant regulations and environmental requirements from different countries necessary for developing new antifouling materials with commercial potential. It concludes by highlighting the current challenges in antifouling material development and future outlooks. Systematic evaluation of newly developed antifouling materials can lead to the emergence of more genuinely applicable solutions, transitioning from merely laboratory products to materials that can be effectively used in real-world applications.

Novel Antifouling Coatings by Zwitterionic Silica Grafting on Glass Substrates

Zwitterionic silica coatings for surface functionalization are greatly prominent because of their simple and fast preparation, high availability, and effective antifouling properties. In this work, two zwitterionic sulfobetaine silane coatings, i.e., mono-SBSi and tris-SBSi, were deposited on glass surfaces and tested for antifouling of biological material and biofilm using human cancer cell and seawater, respectively. The used zwitterionic precursors mono-SBSi and tris-SBSi differ by the number of hydrolyzable silane groups: mono-SBSi contains one trimethoxysilane group, whereas tris-SBSi contains three of these functions. First, X-ray photoelectron spectroscopy indicates the successful grafting of zwitterionic coatings onto a glass surface. Characterization using atomic force microscopy shows the different morphologies and roughness of the two coatings. The glass surface became more hydrophilic after the grafting of zwitterionic coatings than the bare glass substrate. The antifouling properties of two coatings were evaluated via human cancer cell adsorption. Interestingly, the tris-SBSi coating displays a significantly lower level of cell adsorption compared to that of both mono-SBSi coating and the non-modified control surface. The same trend was observed for biofilm formation in seawater. Finally, the toxicity of mono-SBSi and tris-SBSi coatings was evaluated on zebrafish embryos, indicating the good biocompatibility of both coatings. Our results indicate interesting antifouling properties of zwitterionic coatings. The chemical constitution of the used precursor has an impact on the antifouling properties of the formed coating: the tris-SBSi-based zwitterionic silica coatings display improved antifouling properties compared to those of the mono-SBSi-based coating. Besides, the use of trisilylated precursors should result in the formation of more resistant and robust coatings due to the higher number of grafting functions. For all these reasons, we anticipate that tris-SBSi coatings will open new perspectives for antifouling applications for biological environments and implants.

Comparative Investigation of AquaSun Eco-Friendly Antifouling Coating via Rheological and Mechanical Characterization

Rheological and mechanical comparative tests of the new AquaSun antifouling sol-gel coating coated on shipbuilding steel compared to a commercial silyl acrylate antifouling top coat containing cuprous oxide and copper pyrithione show further evidence of the practical viability of this multifunctional coating for the protection of the immersed surfaces from biofouling. AquaSun is a less rigid or less viscous material than commercial top coat but more adherent to the steel substrate. These results support further investigation of this multifunctional sol-gel coating as an eco-friendly antifouling paint.

Robust Underwater Oil-Repellent Biomimetic Ceramic Surfaces: Combining the Stability and Reproducibility of Functional Structures

Robust underwater oil-repellent materials combining high mechanical strength and durability with superwettability and low oil adhesion are needed to build oil-repellent devices able to work in water, to manipulate droplet behavior, etc. However, combining all of these properties within a single, durable material remains a challenge. Herein, we fabricate a robust underwater oil-resistant material (Al₂O₃) with all of the above properties by gel casting. The micro/nanoceramic particles distributed on the surface endow the material with excellent underwater superoleophobicity (∼160°) and low oil adhesion (<4 μN). In addition, the substrate exhibits typical ceramic characteristics such as good antiacid/alkali properties, high salt resistance, and high load tolerance. These excellent properties make the material not only applicable to various liquid environments but also resistant to the impact of particles and other physical damage. More importantly, the substrate could still exhibit underwater superoleophobicity after being worn under specific conditions, as wear will create new surfaces with similar particle size distribution. This approach is easily scalable for mass production, which could open a pathway for the fabrication of practical underwater long-lasting functional interfacial materials.

Antifouling coatings can reduce algal growth while preserving coral settlement

In the early stages after larval settlement, coral spat can be rapidly overgrown and outcompeted by algae, reducing overall survival for coral reef replenishment and supply for restoration programs. Here we investigated three antifouling (AF) coatings for their ability to inhibit algal fouling on coral settlement plugs, a commonly-used restoration substrate. Plugs were either fully or partially coated with the AF coatings and incubated in mesocosm systems with partial recirculation for 37 days to track fouling succession. In addition, settlement of Acropora tenuis larvae was measured to determine whether AF coatings were a settlement deterrent. Uncoated control plugs became heavily fouled, yielding only 4–8% bare substrate on upper surfaces after 37 days. During this period, an encapsulated dichlorooctylisothiazolinone (DCOIT)-coating was most effective in reducing fouling, yielding 61–63% bare substrate. Antiadhesive and cerium dioxide (CeO_2−x) nanoparticle (NP) coatings were less effective, yielding 11–17% and 2% bare substrate, respectively. Average settlement of A. tenuis larvae on the three types of AF-coated plugs did not statistically differ from settlement on uncoated controls. However, settlement on the NP-coating was generally the highest and was significantly higher than settlement found on the antiadhesive- and DCOIT-coating. Furthermore, on plugs only partially-covered with AF coatings, larval settlement on coated NP- areas was significantly higher than settlement on coated antiadhesive- and DCOIT-areas. These results demonstrate that AF coatings can reduce fouling intensity on biologically-relevant timescales while preserving robust levels of coral settlement. This represents an important step towards reducing fine-scale competition with benthic fouling organisms in coral breeding and propagation.

Design and Development of Fluorinated and Biocide-Free Sol–Gel Based Hybrid Functional Coatings for Anti-Biofouling/Foul-Release Activity

Biofouling has destructive effects on shipping and leisure vessels, thus producing severe problems for marine and naval sectors due to corrosion with consequent elevated fuel consumption and higher maintenance costs. The development of anti-fouling or fouling release coatings creates deterrent surfaces that prevent the initial settlement of microorganisms. In this regard, new silica-based materials were prepared using two alkoxysilane cross-linkers containing epoxy and amine groups (i.e., 3-Glycidyloxypropyltrimethoxysilane and 3-aminopropyltriethoxysilane, respectively), in combination with two functional fluoro-silane (i.e., 3,3,3-trifluoropropyl-trimethoxysilane and glycidyl-2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9-hexadecafluorononylether) featuring well-known hydro repellent and anti-corrosion properties. As a matter of fact, the co-condensation of alkoxysilane featuring epoxide and amine ends, also mixed with two opportune long chain and short chain perfluorosilane precursors, allows getting stable amphiphilic, non-toxic, fouling release coatings. The sol–gel mixtures on coated glass slides were fully characterized by FT-IR spectroscopy, while the morphology was studied by scanning electron microscopy (SEM), and atomic force microscopy (AFM). The fouling release properties were evaluated through tests on treated glass slides in different microbial suspensions in seawater-based mediums and in seawater natural microcosms. The developed fluorinated coatings show suitable antimicrobial activities and low adhesive properties; no biocidal effects were observed for the microorganisms (bacteria).

Development of Eco-Friendly Hydrophobic and Fouling-Release Coatings for Blue-Growth Environmental Applications: Synthesis, Mechanical Characterization and Biological Activity

The need to ensure adequate antifouling protection of the hull in the naval sector led to the development of real painting cycles, which involve the spreading of three layers of polymeric material on the hull surface exposed to the marine environment, specifically defined as primer, tie coat and final topcoat. It is already well known that coatings based on suitable silanes provide an efficient and non-toxic approach for the hydrophobic and antifouling/fouling release treatment of surfaces. In the present work, functional hydrophobic hybrid silica-based coatings (topcoats) were developed by using sol-gel technology and deposited on surfaces with the “doctor blade” method. In particular, those organic silanes, featuring opportune functional groups such as long (either fluorinated) alkyl chains, have a notable influence on surface wettability as showed in this study. Furthermore, the hydrophobic behavior of this functionalized coating was improved by introducing an intermediate commercial tie-coat layer between the primer and the topcoat, in order to decrease the wettability (i.e., decreasing the surface energy with a matching increase in the contact angle, CA) and to therefore make such coatings ideal for the design and development of fouling release paints. The hereby synthesized coatings were characterized by optical microscopy, contact angle analysis and a mechanical pull-off test to measure the adhesive power of the coating against a metal substrate typically used in the nautical sector. Analysis to evaluate the bacterial adhesion and the formation of microbial biofilm were related in laboratory and simulation (microcosm) scales, and assessed by SEM analysis.

Sustainability Evaluation of AquaSun Antifouling Coating Production

Relying on a cost-effective and green process that is technically and economically feasible on large scale is not enough to call a technology “sustainable”. We thus evaluate the sustainability of the production of the new “AquaSun” antifouling sol–gel coating with reference to each of the three main dimensions (economic, social, and environmental) of sustainable development. This study will hopefully assist in overcoming the “not invented here” syndrome that still affects many sol–gel technologies, including antifouling coatings derived via the sol–gel process.

High-throughput synthesis of CeO2 nanoparticles for transparent nanocomposites repelling Pseudomonas aeruginosa biofilms

Preventing bacteria from adhering to material surfaces is an important technical problem and a major cause of infection. One of nature's defense strategies against bacterial colonization is based on the biohalogenation of signal substances that interfere with bacterial communication. Biohalogenation is catalyzed by haloperoxidases, a class of metal-dependent enzymes whose activity can be mimicked by ceria nanoparticles. Transparent CeO₂/polycarbonate surfaces that prevent adhesion, proliferation, and spread of Pseudomonas aeruginosa PA14 were manufactured. Large amounts of monodisperse CeO₂ nanoparticles were synthesized in segmented flow using a high-throughput microfluidic benchtop system using water/benzyl alcohol mixtures and oleylamine as capping agent. This reduced the reaction time for nanoceria by more than one order of magnitude compared to conventional batch methods. Ceria nanoparticles prepared by segmented flow showed high catalytic activity in halogenation reactions, which makes them highly efficient functional mimics of haloperoxidase enzymes. Haloperoxidases are used in nature by macroalgae to prevent formation of biofilms via halogenation of signaling compounds that interfere with bacterial cell-cell communication ("quorum sensing"). CeO₂/polycarbonate nanocomposites were prepared by dip-coating plasma-treated polycarbonate panels in CeO₂ dispersions. These showed a reduction in bacterial biofilm formation of up to 85% using P. aeruginosa PA14 as model organism. Besides biofilm formation, also the production of the virulence factor pyocyanin in is under control of the entire quorum sensing systems P. aeruginosa. CeO₂/PC showed a decrease of up to 55% in pyocyanin production, whereas no effect on bacterial growth in liquid culture was observed. This indicates that CeO₂ nanoparticles affect quorum sensing and inhibit biofilm formation in a non-biocidal manner.

Polyphenol effects on CuO-nanoparticle-mediated DNA damage, reactive oxygen species generation, and fibroblast cell death

The ability of ten polyphenolic antioxidants to prevent CuO nanoparticle (NPCuO) and H2O2-mediated DNA damage and cytotoxicity was investigated. Five of the polyphenols (MEPCA, PREGA, MEGA, ECG, and EGCG) prevent NPCuO/H2O2-mediated DNA damage (IC50 values of 7.5-800 μM), three have no effect (PCA, VA, and EC), and two (GA and EGC) result in increased DNA damage. Most polyphenols had similar antioxidant/prooxidant activity in the presence of NPCuO or free copper ions. Electron paramagnetic resonance (EPR) spectroscopy of reactive oxygen species (ROS) generated by NPCuO/H2O2 in the presence of representative polyphenols correlate with results of DNA damage studies: in the presence of NPCuO/H2O2, MEPCA prevents ROS formation, VA has no effect on ROS levels, and EGC increases ROS levels. EPR results with CuO nanoparticles washed to remove dissolved copper in solution (wCuO) in the presence of H2O2/ascorbate suggest that MEPCA prevents ROS formation on the nanoparticle surface in addition to preventing ROS formation from dissolved copper. In mouse fibroblast (L929) cells, combining NPCuO with H2O2 results in significantly greater cytotoxicity than observed for either component alone. After 3 h incubation with MEPCA or MEGA, the viability loss in L929 cells induced by NPCuO/H2O2 challenge was significantly rescued at physiologically relevant polyphenol levels (1 μM). These studies show that polyphenols can protect DNA and inhibit cytotoxicity generated by NPCuO under oxidative stress conditions.

Functional nanomaterials, synergisms, and biomimicry for environmentally benign marine antifouling technology

Marine biofouling remains one of the key challenges for maritime industries, both for seafaring and stationary structures. Currently used biocide-based approaches suffer from significant drawbacks, coming at a significant cost to the environment into which the biocides are released, whereas novel environmentally friendly approaches are often difficult to translate from lab bench to commercial scale. In this article, current biocide-based strategies and their adverse environmental effects are briefly outlined, showing significant gaps that could be addressed through advanced materials engineering. Current research towards the use of natural antifouling products and strategies based on physio-chemical properties is then reviewed, focusing on the recent progress and promising novel developments in the field of environmentally benign marine antifouling technologies based on advanced nanocomposites, synergistic effects and biomimetic approaches are discussed and their benefits and potential drawbacks are compared to existing techniques.

Slippery-Liquid-Infused Electrostatic Flocking Surfaces for Marine Antifouling Application

Most marine antifouling coatings rely on the release of toxic biocides to prevent fouling organisms from attaching, causing environmental pollution. This work proposes a biocide-free environmentally friendly marine antifouling strategy. Slippery-liquid-infused electrostatic flocking surfaces (S-EFSs) were prepared by combining electrostatic flocking and slippery liquid infusion. They exhibited complete mussel resistance after comparing adhesion to the surface of different materials in the laboratory. In addition, the unique surface morphology including lubricant was found to be crucial to their antifouling performance. Real-time polymerase chain reaction showed that different surfaces significantly affected the gene-expression levels of the mussels' foot proteins, where higher levels on S-EFSs meant that the mussels tried to secrete more proteins but they failed to adhere. Moreover, a 148-day field test showed that S-EFSs can resist not only mussels but also tubeworms, tunicates, and barnacles, and the total fouling area decreased by more than 50% compared to control samples. Notably, the maturity of electrostatic flocking technology and the simplicity of the modification steps used endow this strategy with the potential to significantly reduce the economic loss caused by marine biofouling in practical applications.

Nanostructured Surface Finishing and Coatings: Functional Properties and Applications

This review presents current literature on different nanocomposite coatings and surface finishing for textiles, and in particular this study has focused on smart materials, drug-delivery systems, industrial, antifouling and nano/ultrafiltration membrane coatings. Each of these nanostructured coatings shows interesting properties for different fields of application. In this review, particular attention is paid to the synthesis and the consequent physico-chemical characteristics of each coating and, therefore, to the different parameters that influence the substrate deposition process. Several techniques used in the characterization of these surface finishing coatings were also described. In this review the sol-gel method for preparing stimuli-responsive coatings as smart sensor materials is described; polymers and nanoparticles sensitive to pH, temperature, phase, light and biomolecules are also treated; nanomaterials based on phosphorus, borates, hydroxy carbonates and silicones are used and described as flame-retardant coatings; organic/inorganic hybrid sol-gel coatings for industrial applications are illustrated; carbon nanotubes, metallic oxides and polymers are employed for nano/ultrafiltration membranes and antifouling coatings. Research institutes and industries have collaborated in the advancement of nanotechnology by optimizing conversion processes of conventional materials into coatings with new functionalities for intelligent applications.

Sol-Gel-Based Hybrid Materials as Antifouling and Fouling-Release Coatings for Marine Applications

Hybrid materials (HMs) offer unique properties as they combine inorganic and organic components into a single material. Here, we developed HM coatings for marine antifouling applications using sol-gel chemistry and naturally occurring polysaccharides. The coatings were characterized by spectroscopic ellipsometry, contact angle goniometry, AFM, and ATR-FTIR, and their stability was tested in saline media. Marine antifouling and fouling-release properties were tested in laboratory assays against the settlement of larvae of the barnacle Balanus improvisus and against the settlement and removal of the diatom Navicula incerta. Furthermore, laboratory data were confirmed in short-term dynamic field assays in Florida, USA. All hybrid coatings revealed a superior performance in the assays compared to a hydrophobic reference. Within the hybrids, those with the highest degree of hydrophilicity and negative net charge across the surface performed best. Alginate and heparin showed good performance, making these hybrid materials promising building blocks for fouling-resistant coatings.

Powder and High-Solid Coatings as Anticorrosive Solutions for Marine and Offshore Applications? A Review

The constant change in coating technology and environmental regulations has led to the development of low-solvent to solvent-free organic coatings, such as powder and high-solid coatings. These two technologies are well developed, but are still not the preferred choice when considering anticorrosive coating for marine and offshore applications. This mostly arise from a lack of perspective in their long-term behavior and from the difficulty in their applications. This review’s principal aim is to describe powder and high-solid technologies from their formulation and application to their use in marine and offshore applications while recalling and giving key notions needed when the field of anticorrosive coatings is considered. First, the requirement for coatings to be called anticorrosive will be given alongside with their protection and failure mechanisms. The formulation and application for high-solid and powder coatings will be exposed followed by the description of the type of coating chemistry used in harsh environment. Finally, high-solid and powder coatings behavior in these types of environment will be discussed.

Grafting polysiloxane onto ultrafiltration membranes to optimize surface energy and mitigate fouling

Conventional approaches to mitigate fouling of membrane surfaces impart hydrophilicity to the membrane surface, which increases the water of hydration and fluidity near the surface. By contrast, we demonstrate here that tuning the membrane surface energy close to that of the dispersive component of water surface tension (21.8 mN m^-1) can also improve the antifouling properties of the membrane. Specifically, ultrafiltration (UF) membranes were first modified using polydopamine (PDA) followed by grafting of amine-terminated polysiloxane (PSi-NH₂). For example, with 2 g L^-1 PSi-NH₂ coating solution, the obtained coating layer contains 53% by mass fraction PSi-NH₂ and exhibits a total surface energy of 21 mN m^-1, decreasing the adsorption of bovine serum albumin by 44% compared to the unmodified membrane. When challenged with 1 g L^-1 sodium alginate in a constant-flux crossflow system, the PSi-NH₂-grafted membrane exhibits a 70% lower fouling rate than the pristine membrane at a water flux of 110 L (m² h)^-1 and good stability when cleaned with NaOH solutions.

Hybrid Sol-gel Coatings for Corrosion Mitigation: A Critical Review

The corrosion process is a major source of metallic material degradation, particularly in aggressive environments, such as marine ones. Corrosion progression affects the service life of a given metallic structure, which may end in structural failure, leakage, product loss and environmental pollution linked to large financial costs. According to NACE, the annual cost of corrosion worldwide was estimated, in 2016, to be around 3%-4% of the world's gross domestic product. Therefore, the use of methodologies for corrosion mitigation are extremely important. The approaches used can be passive or active. A passive approach is preventive and may be achieved by emplacing a barrier layer, such as a coating that hinders the contact of the metallic substrate with the aggressive environment. An active approach is generally employed when the corrosion is set in. That seeks to reduce the corrosion rate when the protective barrier is already damaged and the aggressive species (i.e., corrosive agents) are in contact with the metallic substrate. In this case, this is more a remediation methodology than a preventive action, such as the use of coatings. The sol-gel synthesis process, over the past few decades, gained remarkable importance in diverse areas of application. Sol-gel allows the combination of inorganic and organic materials in a single-phase and has led to the development of organic-inorganic hybrid (OIH) coatings for several applications, including for corrosion mitigation. This manuscript succinctly reviews the fundamentals of sol-gel concepts and the parameters that influence the processing techniques. The state-of-the-art of the OIH sol-gel coatings reported in the last few years for corrosion protection, are also assessed. Lastly, a brief perspective on the limitations, standing challenges and future perspectives of the field are critically discussed.

Silicone-Based Fouling-Release Coatings for Marine Antifouling

Marine biofouling profoundly influences marine industries and activities. It slows the speed and increases the fuel consumption of ships, corrodes offshore platforms, and blocks seawater pipelines. The most effective and economical antifouling approach uses coatings. Fouling-release coatings (FRCs) with low surface free energy and high elasticity weakly adhere to marine organisms, so they can be readily removed by the water shear force. FRCs have attracted increasing interest because they are biocide-free and hence ecofriendly. However, traditional silicone-based FRCs have weak adhesion to substrates, low mechanical strength, and low fouling resistance, limiting their applications. In recent years, many attempts have been made to improve their mechanical properties and fouling resistance. This review deals with the progress in the construction of high-performance silicone-based fouling-release surfaces.

Progress in biomimetic leverages for marine antifouling using nanocomposite coatings

Because of the environmental and economic casualties of biofouling on maritime navigation, modern studies have been devoted toward formulating advanced nanoscale composites in the controlled development of effective marine antifouling self-cleaning surfaces.

Assessment of Antifouling Potential of Novel Transparent Sol Gel Coatings for Application in the Marine Environment

In recent years, there has become a growing need for the development of antifouling technology for application in the marine environment. The accumulation of large quantities of biomass on these surfaces cause substantial economic burdens within the marine industry, or adversely impact the performance of sensor technologies. Here, we present a study of transparent coatings with potential for applications on sensors or devices with optical windows. The focus of the study is on the abundance and diversity of biofouling organisms that accumulate on glass panels coated with novel transparent or opaque organically modified silicate (ORMOSIL) coatings. The diatom assessment was used to determine the effectiveness of the coatings against biofouling. Test panels were deployed in a marine environment in Galway Bay for durations of nine and thirteen months to examine differences in biofilm formation in both microfouling and macrofouling conditions. The most effective coating is one which consists of precursor, tetraethyl orthosilicate (HC006) that has a water contact angle > 100, without significant roughness (43.52 nm). However, improved roughness and wettability of a second coating, diethoxydimethylsilane (DMDEOS), showed real promise in relation to macrofouling reduction.

Polymer-Based Marine Antifouling and Fouling Release Surfaces: Strategies for Synthesis and Modification

In marine industries, the accumulation of organic matter and marine organisms on ship hulls and instruments limits performance, requiring frequent maintenance and increasing fuel costs. Current coatings technology to combat this biofouling relies heavily on the use of toxic, biocide-containing paints. These pose a serious threat to marine ecosystems, affecting both target and nontarget organisms. Innovation in the design of polymers offers an excellent platform for the development of alternatives, but the creation of a broad-spectrum, nontoxic material still poses quite a hurdle for researchers. Surface chemistry, physical properties, durability, and attachment scheme have been shown to play a vital role in the construction of a successful coating. This review explores why these characteristics are important and how recent research accounts for them in the design and synthesis of new environmentally benign antifouling and fouling release materials.

Silicon Nanoribbon pH Sensors Protected by a Barrier Membrane with Carbon Nanotube Porins

Limited biocompatibility and fouling propensity can restrict real-world applications of a large variety of biosensors. Biological systems are adept at protecting and separating vital components of biological machinery with semipermeable membranes that often contain defined pores and gates to restrict transmembrane transport only to specific species. Here we use a similar approach for creating fouling-resistant pH sensors. We integrate silicon nanoribbon transistor sensors with an antifouling lipid bilayer coating that contains proton-permeable carbon nanotube porin (CNTP) channels and demonstrate robust pH detection in a variety of complex biological fluids.

Hydrolyzable Additive-Based Silicone Elastomers: A New Approach for Antifouling Coatings

Fouling Release Coatings are marine antifouling coatings based on silicone elastomers. Contrary to commonly used biocide-based antifouling coatings, they do not release biocides into the marine environment, however, they suffer from poor antifouling efficacy during idle periods. To improve their antifouling performances in static conditions, various amounts of hydrolyzable polymers were incorporated within a silicone matrix. These hydrolyzable polymers were chosen for the well-known hydrolytic degradation mechanism of their main chain, e.g. poly(ε-caprolactone) (PCL), or of their ester pending groups, e.g. poly(bis(trimethylsilyloxy)methylsilyl methacrylate) (PMATM2). The degradation kinetics of such hydrolyzable silicone coatings were assessed by mass loss measurements during immersion in deionized water. Coatings containing PMATM2 exhibited a maximum mass loss after 12 weeks, whereas PCL-based coatings showed no significant mass loss after 24 weeks. Dynamic contact angle measurements revealed the modifications of the coatings surface chemistry with an amphiphilic behavior after water exposure. The attachment of macrofoulers on these coatings were evaluated by field tests in the Mediterranean Sea, demonstrating the short or long-term antifouling effect of these hydrolyzable polymers embedded in the silicone matrix. The settlement of A. amphitrite barnacles on the different coatings indicated inhospitable behaviors towards larval barnacles for coatings with at least 15 wt % of additives.

Codeposition of Polydopamine and Zwitterionic Polymer on Membrane Surface with Enhanced Stability and Antibiofouling Property

Although abundant works have been developed in mussel-inspired antifouling coatings, most of them suffer from poor chemical stability, especially in a strongly alkaline environment. Herein, we report a robust one-step mussel-inspired method to construct a highly chemical stable and excellent antibiofouling membrane surface coating with a highly efficient codeposition of polydopamine (PDA) with zwitterionic polymer. In the study, PDA and polyethylenimine-quaternized derivative (PEI-S) are codeposited on the surface of poly(ether sulfone) (PES) ultrafiltration membrane in water at room temperature. In contrast to individual PDA coating, the obtained PDA/PEI-S coating exhibits excellent chemical stability even in a strongly alkaline environment owing to the cross-linking and unexpected cation-π interaction between the PEI-S and PDA. Thanks to the introduction of PEI-S, systematic protein adsorption tests and bacteria adhesion experiments demonstrated that the surfaces could prevent bovine serum fibrinogen and lysozyme adsorption and could reduce Gram-positive bacteria S. aureus and Gram-negative bacteria E. coli adhesion. Benefiting from the versatile functionality of PDA, the proposed strategy is not limited to PES membrane surface but also others such as poly(ethylene terephthalate) sheets and commercial polypropylene microfiltration membranes. Overall, this work enriches the exploration of a remarkable coating with enhanced stability and excellent antifouling property via a facile, robust, and material-independent approach to modifying the membrane surface.

A new approach to testing potential leaching toxicity of fouling release coatings (FRCs)

Fouling release coatings (FRCs) are today the main environment-friendly alternative to traditional self-polishing coatings, that continuously release biocides and/or heavy metals into water. FRCs are available on the market as environmentally friendly AF paints and most of them do not contain bioactive agents, however no complete and reliable assessment of their environmental impact has yet been carried out. Only few literature data proving their AF efficacy combined with a demonstrated lack of toxicological effects are available. Ecotoxicological bioassays are commonly used to predict the potential environmental impact of traditional AF paints. Standardized methodologies to obtain leaching products from biocide-based paints are available, while few studies propose experimental methods to assess the potential effects of biocide-free FRCs leachates on non-target organisms. The aim of this work is to propose an experimental protocol to obtain leaching products from biocide-free FRCs in order to evaluate the potential release of substances having toxic effects, by means of an ecotoxicological bioassay. Two ecotoxicological end-points with different sensitivity levels were considered (multi-end-point approach). Five silicone-based commercial coatings were used: their leaching products were collected after different immersion times following the developed experimental method and then two ecotoxicological end-points were evaluated on II stage nauplii of the crustacean Amphibalanus amphitrite as model organism. Moreover, chemical analyses were performed on leachates collected after each immersion time, focusing on the presence of metals in leaching products. From the results obtained from the bioassay, even if not indicative of the real environmental impact of FRCs, a release of toxic substances was observed from tested coatings during early immersion stages, likely to affect the exposed model organism. The potential leaching toxicity of the five tested products was compared. No clear correspondence could be identified between the concentrations of metals detected in leachates and the obtained ecotoxicological data, thus suggesting that other active components might be released by FRCs responsible for the toxic effects pointed out on A. amphitrite larvae.

Functional Enzyme Mimics for Oxidative Halogenation Reactions that Combat Biofilm Formation

Transition-metal oxide nanoparticles and molecular coordination compounds are highlighted as functional mimics of halogenating enzymes. These enzymes are involved in halometabolite biosynthesis. Their activity is based upon the formation of hypohalous acids from halides and hydrogen peroxide or oxygen, which form bioactive secondary metabolites of microbial origin with strong antibacterial and antifungal activities in follow-up reactions. Therefore, enzyme mimics and halogenating enzymes may be valuable tools to combat biofilm formation. Here, halogenating enzyme models are briefly described, enzyme mimics are classified according to their catalytic functions, and current knowledge about the settlement chemistry and adhesion of fouling organisms is summarized. Enzyme mimics with the highest potential are showcased. They may find application in antifouling coatings, indoor and outdoor paints, polymer membranes for water desalination, or in aquacultures, but also on surfaces for food packaging, door handles, hand rails, push buttons, keyboards, and other elements made of plastic where biofilms are present. The use of natural compounds, formed in situ with nontoxic and abundant metal oxide enzyme mimics, represents a novel and efficient "green" strategy to emulate and utilize a natural defense system for preventing bacterial colonization and biofilm growth.

Underwater Mechanically Robust Oil-Repellent Materials: Combining Conflicting Properties Using a Heterostructure

The development of underwater mechanically robust oil-repellent materials is important due to the high demand for these materials with the increase in underwater activities. Based on the previous study, a new strategy is demonstrated to prepare underwater mechanically robust oil-repellent materials by combining conflicting properties using a heterostructure, which has a layered hydrophobic interior structure with a columnar hierarchical micro/nanostructure on the surface and a hydrophilic outer structure. The surface hydrophilic layer imparts underwater superoleophobicity and low oil adhesion to the material, which has oil contact angle of larger than 150° and adhesion of lower than 2.8 µN. The stability of the mechanical properties stemming from the interior hydrophobic-layered structure enables the material to withstand high weight loads underwater. The tensile stress and the hardness of such a heterostructure film after 1 month immersion in seawater and pH solution are in the range from 83.92 ± 8.22 to 86.73 ± 7.8 MPa and from 83.88 ± 6.8 to 86.82 ± 5.64 MPa, respectively, which are superior to any underwater oil-repellent material currently reported.

Antifouling and Photocatalytic Antibacterial Activity of the AquaSun Coating in Seawater and Related Media

Prolonged testing of the new xerogel photocatalytic coating AquaSun applied to a surface probe immersed in ocean water irradiated with simulated solar radiation shows excellent action against biofouling. Activated by moderate solar radiation, the organosilica film has also good antimicrobial properties. Considering the high stability, the environmental footprint, and the low cost of this sol-gel marine coating, the technology has significant potential toward replacing conventional antifouling and foul-release coatings with a single product of broad applicability.

Que faire? A Bioeconomy and Solar Energy Institute at Italy's Research Council in the Context of the Global Transition to the Solar Economy

Driven by insight for which new research and education requires new institutional organisation, and drawing on two decades of research and educational efforts, we devise the profile and activities of a new bioeconomy and solar energy institute at Italy's Research Council. We further articulate the institute's activities suggesting avenues on how to deploy sound and giving more useful research, education and policy advice in these crucial fields for making tomorrow's common development sustainable. The outcomes of the study are of general interest, because the transition to a solar economy is of intrinsic global nature and the challenges involved are similar in many countries.

Arginine-Based Polymer Brush Coatings with Hydrolysis-Triggered Switchable Functionalities from Antimicrobial (Cationic) to Antifouling (Zwitterionic)

Arginine polymer based coatings with switchable properties were developed on glass slides (GS) to demonstrate the smart transition from antimicrobial (cationic) to fouling-resistant (zwitterionic) surfaces. l-Arginine methyl ester-methacryloylamide (Arg-Est) and l-arginine-methacryloylamide (Arg-Me) polymer brushes were grafted from the GS surface via surface-initiated reversible addition-fragmentation chain-transfer (SI-RAFT) polymerization. In comparison to the pristine GS and Arg-Me graft polymerized GS (GS-Arg-Me) surfaces, the Arg-Est polymer brushes-functionalized GS surfaces exhibit a superior antimicrobial activity. Upon hydrolysis treatment, the strong bactericidal efficacy switches to good resistance to adsorption of bovine serum albumin (BSA), the adhesion of Gram-positive bacteria Staphylococcus aureus and Gram-negative bacteria Escherichia coli, as well as the attachment of Amphora coffeaeformis. In addition, the switchable coatings are proven to be biocompatible. The stability and durability of the switchable coatings are also ascertained after exposure to filtered seawater for 30 days. Therefore, deposition of the proposed "smart coatings" offers another environmentally friendly alternative for combating biofouling.

Haloperoxidase Mimicry by CeO2-x Nanorods Combats Biofouling

CeO_2-x nanorods are functional mimics of natural haloperoxidases. They catalyze the oxidative bromination of phenol red to bromophenol blue and of natural signaling molecules involved in bacterial quorum sensing. Laboratory and field tests with paint formulations containing 2 wt% of CeO_2-x nanorods show a reduction in biofouling comparable to Cu₂ O, the most typical biocidal pigment.

Hybrid Sol-Gel-Derived Films That Spontaneously Form Complex Surface Topographies

Surface patterns over multiple length scales are known to influence various biological processes. Here we report the synthesis and characterization of new, two-component xerogel thin films derived from carboxyethylsilanetriol (COE) and tetraethoxysilane (TEOS). Atomic force microscopy (AFM) reveals films surface with branched and hyper branched architectures that are ∼2 to 30 μm in diameter, that extend ∼3 to 1300 nm above the film base plane with surface densities that range from 2 to 77% surface area coverage. Colocalized AFM and Raman spectroscopy show that these branched structures are COE-rich domains, which are slightly stiffer (as shown from phase AFM imaging) and exhibit lower capacitive force in comparison with film base plane. Raman mapping reveals there are also discrete domains (≤300 nm in diameter) that are rich in COE dimers and densified TEOS, which do not appear to correspond with any surface structure seen by AFM.

The performance of hybrid titania/silica-derived xerogels as active antifouling/fouling-release surfaces against the marine alga Ulva linza: in situ generation of hypohalous acids

Mixed titania/silica xerogels were prepared using titanium tetraisopropoxide (TTIP) and tetraethoxy orthosilicate (TEOS). Xerogel properties were modified by incorporating n-octyltriethoxysilane (C8). The xerogels catalyze the oxidation of bromide and chloride with hydrogen peroxide (H2O2) to produce hypohalous acids at pH 7 and pH 8. The antifouling/ fouling-release performance of a TTIP/C8/TEOS xerogel in the presence and absence of H2O2 was evaluated for the settlement of zoospores of the marine alga Ulva linza and for the removal of sporelings (young plants). In the absence of H2O2, differences in the settlement of zoospores and removal of sporelings were not significant relative to a titanium-free C8/TEOS xerogel. Addition of H2O2 gave a significant reduction in zoospore settlement and sporeling removal relative to the C8/TEOS xerogel and relative to peroxide-free conditions. The impact of TTIP on xerogel characteristics was evaluated by comprehensive contact angle analysis, scanning electron microscopy, and X-ray photoelectron spectroscopy.

Antifouling Properties of Fluoropolymer Brushes toward Organic Polymers: The Influence of Composition, Thickness, Brush Architecture, and Annealing

Fluoropolymer brushes are widely used to prevent nonspecific adsorption of commercial polymeric or biological materials due to their strongly hydrophobic character. Herein, a series of fluoropolymer brushes with different compositions, thicknesses and molecular architectures was prepared via surface-initiated atom transfer radical polymerization (ATRP). Subsequently, the antifouling properties of these fluoropolymer brushes against organic polymers were studied in detail using X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) measurements and polystyrene as a representative fouling polymer. Among all of the molecular architectures studied, homopolymerized methacrylate-based fluoropolymer brushes (PMAF17) show the best antifouling properties. Annealing the fluoropolymer brushes improves the antifouling property dramatically due to the reregulated surface composition. These fluoropolymer brushes can be combined with, e.g., micro- and nanostructuring and other advanced materials properties to yield even better long-term antifouling behavior under harsh environments.

Nanoflower-Like Bi2 WO6 Encapsulated in ORMOSIL as a Novel Photocatalytic Antifouling and Foul-Release Coating

Herein, the first multi-purpose antifouling and foul-release photocatalytic coating based on ORMOSIL thin films doped with nanoflower-like Bi2 WO6 is described. Irradiation with visible light of the new films immersed in water produces significant amounts of H2 O2 by photocatalytic oxidation of water, and allows the degradation of (bio)organic pollutants at the outer surface of the xerogel film.

Self-Healing Underwater Superoleophobic and Antibiofouling Coatings Based on the Assembly of Hierarchical Microgel Spheres

Marine biofouling has been plaguing people for thousands of years. While various strategies have been developed for antifouling (including superoleophobic) coatings, none of these exhibits self-healing properties because the bestowal of a zoetic self-repairing function to lifeless artificial water/solid interfacial materials is usually confronted with tremendous challenges. Here, we present a self-repairing underwater superoleophobic and antibiofouling coating through the self-assembly of hydrophilic polymeric chain modified hierarchical microgel spheres. The obtained surface material not only has excellent underwater superoleophobicity but also has very good subaqueous antibiofouling properties. More importantly, this surface material can recover the oil- and biofouling-resistant properties once its surface is mechanically damaged, similar to the skins of some marine organisms such as sharks or whales. This approach is feasible and easily mass-produced and could open a pathway and possibility for the fabrication of other self-healing functional water/solid interfacial materials.