Perovskites as substitutes of noble metals for heterogeneous catalysis: dream or reality

Operando Soft X-ray Absorption of LaMn1-x Co x O3 Perovskites for CO Oxidation

We employed operando soft X-ray absorption spectroscopy (XAS) to monitor the changes in the valence states and spin properties of LaMn1-x Co x O3 catalysts subjected to a mixture of CO and O2 at ambient pressure. Guided by simulations based on charge transfer multiplet theory, we quantitatively analyze the Mn and Co 2p XAS as well as the oxygen K-edge XAS spectra during the reaction process. The Mn sites are particularly sensitive to the catalytic reaction, displaying dynamics in their oxidation state. When Co doping is introduced (x ≤ 0.5), Mn oxidizes from Mn2+ to Mn3+ and Mn4+, while Co largely maintains a valence state of Co2+. In the case of LaCoO3, we identify high-spin and low-spin Co3+ species combined with Co2+. Our investigation underscores the importance to consider the spin and valence states of catalyst materials under operando conditions.

LaMnO3-Type Perovskite Nanofibers as Effective Catalysts for On-Cell CH4 Reforming via Solid Oxide Fuel Cells

CH4 has become the most attractive fuel for solid oxide fuel cells due to its wide availability, narrow explosion limit range, low price, and easy storage. Thus, we present the concept of on-cell reforming via SOFC power generation, in which CH4 and CO2 can be converted into H2 and the formed H2 is electrochemically oxidized on a Ni-BZCYYb anode. We modified the porosity and specific surface area of a perovskite reforming catalyst via an optimized electrostatic spinning method, and the prepared LCMN nanofibers, which displayed an ideal LaMnO3-type perovskite structure with a high specific surface area, were imposed on a conventional Ni-BZCYYb anode for on-cell CH4 reforming. Compared to LCMN nanoparticles used as on-cell reforming catalysts, the NF-SOFC showed lower ohmic and polarization resistances, indicating that the porous nanofibers could reduce the resistances of fuel gas transport and charge transport in the anode. Accordingly, the NF-SOFC displayed a maximum power density (MPD) of 781 mW cm-2 and a stable discharge voltage of around 0.62 V for 72 h without coking in the Ni-BZCYYb anode. The present LCMN NF materials and on-cell reforming system demonstrated stability and potential for highly efficient power generation with hydrocarbon fuels.

Transforming Plain LaMnO3 Perovskite into a Powerful Ozonation Catalyst: Elucidating the Mechanisms of Simultaneous A and B Sites Modulation for Enhanced Toluene Degradation

Herein, we propose preferential dissolution paired with Cu-doping as an effective method for synergistically modulating the A- and B-sites of LaMnO3 perovskite. Through Cu-doping into the B-sites of LaMnO3, specifically modifying the B-sites, the double perovskite La2CuMnO6 was created. Subsequently, partial La from the A-sites of La2CuMnO6 was etched using HNO3, forming novel La2CuMnO6/MnO2 (LCMO/MnO2) catalysts. The optimized catalyst, featuring an ideal Mn:Cu ratio of 4.5:1 (LCMO/MnO2-4.5), exhibited exceptional catalytic ozonation performance. It achieved approximately 90% toluene degradation with 56% selectivity toward CO2, even under ambient temperature (35 °C) and a relatively humid environment (45%). Modulation of A-sites induced the elongation of Mn-O bonds and decrease in the coordination number of Mn-O (from 6 to 4.3) in LCMO/MnO2-4.5, resulting in the creation of abundant multivalent Mn and oxygen vacancies. Doping Cu into B-sites led to the preferential chemisorption of toluene on multivalent Cu (Cu(I)/Cu(II)), consistent with theoretical predictions. Effective electronic supplementary interactions enabled the cycling of multiple oxidation states of Mn for ozone decomposition, facilitating the production of reactive oxygen species and the regeneration of oxygen vacancies. This study establishes high-performance perovskites for the synergistic regulation of O3 and toluene, contributing to cleaner and safer industrial activities.

Optimizing the Catalytic Performance of Ba1-xCexMnO3 and Ba1-xLaxCu0.3Mn0.7O3 Perovskites for Soot Oxidation in Simulated GDI Exhaust Conditions

Ba1-xCexMnO3 (BM-Cex) and Ba1-xLaxMn0.7Cu0.3O3 (BMC-Lax) perovskite-type mixed oxides were synthesized using the sol-gel method adapted for aqueous media with different values of x (0, 0.1, 0.3, 0.6) to estimate the effect of the degree of the partial substitution of Ba by Ce or La on the structure and properties that are relevant for their use as catalysts for gasoline direct injection (GDI) soot oxidation. The samples were deeply characterized by ICP-OES, XRD, XPS, N2 adsorption, H2-TPR, and O2-TPD, and their potential as catalysts for soot oxidation has been analyzed in various scenarios that replicate the exhaust conditions of a GDI engine. By comparing the catalytic performance for soot oxidation of the two tested series (BM-Cex and BMC-Lax) and in the two conditions used (100% He and 1% O2 in He), it could be concluded that (i) in the absence of oxygen in the reaction atmosphere (100% He), BMC-La0.1 is the best catalyst, as copper is also able to catalyze the soot oxidation; and (ii) if oxygen is present in the reaction atmosphere (1% O2/He), BM-Ce0.1 is the most-active catalyst as it presents a higher proportion of Mn(IV) than BMC-La0.1. Thus, it seems that the addition of an amount of Ce or La higher than that corresponding to x = 0.1 in Ba1-xCexMnO3 and Ba1-xLaxCu0.3Mn0.7O3 does not allow us to improve the catalytic performance of BM-Ce0.1 and BMC-La0.1 for soot oxidation in the tested conditions.

Effect of Rh Doping on Optical Absorption and Oxygen Evolution Reaction Activity on BaTiO3 (001) Surfaces

In the present work, we investigate the potential of modified barium titanate (BaTiO3), an inexpensive perovskite oxide derived from earth-abundant precursors, for developing efficient water oxidation electrocatalysts using first-principles calculations. Based on our calculations, Rh doping is a way of making BaTiO3 absorb more light and have less overpotential needed for water to oxidize. It has been shown that a TiO2-terminated BaTiO3 (001) surface is more promising from the point of view of its use as a catalyst. Rh doping expands the spectrum of absorbed light to the entire visible range. The aqueous environment significantly affects the ability of Rh-doped BaTiO3 to absorb solar radiation. After Ti→Rh replacement, the doping ion can take over part of the electron density from neighboring oxygen ions. As a result, during the water oxidation reaction, rhodium ions can be in an intermediate oxidation state between 3+ and 4+. This affects the adsorption energy of reaction intermediates on the catalyst's surface, reducing the overpotential value.

Optimization of switching charge and recoverable energy density mediated by structural transformation in Sr-substituted BaNiO3 perovskites

Because of their distinctive characteristics, ferroelectric perovskites are considered among the most potent and auspicious candidates for energy storage and pulsed power devices. But their energy storage properties and switching capabilities need to be further enhanced which can be done by substitutions of appropriate cations. Hence, a series of lead-free Ba1-xSrxNiO3 (x = 0.00, 0.33, 0.67, and 1.00) ceramics was fabricated using a sol-gel auto combustion technique. Rietveld's refinement of X-ray diffraction plots verified the complete development of the required hexagonal perovskite structure. Scanning electron microscopy images revealed a gradual increase in average grain sizes and agglomeration with the increase in Sr-content. Moreover, the existence of all the constituent elements exactly in proportion to their stoichiometric ratios was verified by energy dispersive X-ray spectroscopy. The characteristic parameters of ferroelectric materials such as ferroelectric response, electrical conductivity, and switching charge density were also determined. The P-E loops indicated that with the increase in Sr-content, the coercive field, remanent polarization, and maximum polarization all decreased gradually, but the recoverable energy density (Wrec) increased as the loops became slimmer. The maximum value of Wrec was found in the Ba0.33Sr0.67NiO3 sample. Moreover, SrNiO3 exhibited minimum energy loss with the highest efficiency of ∼47.21%. The existence of a current barrier in all the samples was proved from the low leakage current values (∼10-7 A). In addition, the pure SrNiO3 showed a low electrical conductivity and minimum value of switching charge density. All these findings make SrNiO3 a promising candidate for fast switching and energy storage applications.

Perovskite Oxides: Syntheses and Perspectives on Their Application for Nitrate Reduction

Over the decades, the rise in nitrate levels in the ecosystem has posed a serious threat to the continuous existence of humans, fauna, and flora. The deleterious effects of increasing levels of nitrates in the ecosystem have led to adverse health and environmental implications in the form of methemoglobinemia and eutrophication, respectively. Different pathways/routes for the syntheses of perovskites and their oxides were presented in this review. In recent times, electrocatalytic reduction has emerged as the most utilized technique for the conversion of nitrates into ammonia, an industrial feedstock. According to published papers, the efficiency of various perovskites and their oxides used for the electrocatalytic reduction of nitrate achieved a high Faradaic efficiency of 98%. Furthermore, studies published have shown that there is a need to improve the chemical stability of perovskites and their oxides during scale-up applications, as well as their scalability for industrial applications.

Strategic Design and Insights into Lanthanum and Strontium Perovskite Oxides for Oxygen Reduction and Oxygen Evolution Reactions

Perovskite oxides exhibit bifunctional activity for both oxygen reduction (ORR) and oxygen evolution reactions (OER), making them prime candidates for energy conversion in applications like fuel cells and metal-air batteries. Their intrinsic catalytic prowess, combined with low-cost, abundance, and diversity, positions them as compelling alternatives to noble metal and metal oxides catalysts. This review encapsulates the nuances of perovskite oxide structures and synthesis techniques, providing insight into pivotal active sites that underscore their bifunctional behavior. The focus centers on the breakthroughs surrounding lanthanum (La) and strontium (Sr)-based perovskite oxides, specifically their roles in zinc-air batteries (ZABs). An introduction to the mechanisms of ORR and OER is provided. Moreover, the light is shed on strategies and determinants central to optimizing the bifunctional performance of La and Sr-based perovskite oxides.

Synthesis and Catalytic Performance of High-Entropy Rare-Earth Perovskite Nanofibers: (Y0.2La0.2Nd0.2Gd0.2Sm0.2)CoO3 in Low-Temperature Carbon Monoxide Oxidation

This study investigated the catalytic properties of low-temperature oxidation of carbon monoxide, focusing on (Y0.2La0.2Nd0.2Gd0.2Sm0.2)CoO3 synthesized via a glycothermal method using 1,4-butanediol and diethylene glycol at 250 °C. This synthesis route bypasses the energy-intensive sintering process at 1200 °C while maintaining a high-entropy single-phase structure. The synthesized material was characterized structurally and chemically by X-ray diffraction and SEM/EDX analyses. The material was shown to form nanofibers of (Y0.2La0.2Nd0.2Gd0.2Sm0.2)CoO3, thereby increasing the active surface area for catalytic reactions, and crystallize in the model Pbnm space group of distorted perovskite cell. Using a custom setup to investigate catalytic properties of (Y0.2La0.2Nd0.2Gd0.2Sm0.2)CoO3, the CO oxidation behavior of those high-entropy perovskite oxide was investigated, showing an overall conversion of 78% at 50 °C and 97% at 100 °C. These findings highlight the effective catalytic activity of nanofibers of (Y0.2La0.2Nd0.2Gd0.2Sm0.2)CoO3 under mild conditions and their versatility in various catalytic processes of robust CO neutralization. The incorporation of rare-earth elements into a high-entropy structure could impart unique catalytic properties, promoting a synergistic effect that enhances performance.

Molecularly thin, two-dimensional all-organic perovskites

Recently, the emergence of all-organic perovskites with three-dimensional (3D) structures has expanded the potential applications of perovskite materials. However, the synthesis and utilization of all-organic perovskites in 2D form remain largely unexplored because the design principle has not been developed. We present the successful synthesis of a metal-free 2D layered perovskite, denoted as the Choi-Loh van der Waals phase (CL-v phase), with the chemical formula A2B2X4, where A represents a larger-sized cation compared to B and X denotes an anion. The CL-v phase exhibits a van der Waals gap enabled by interlayer hydrogen bonding and can be exfoliated or grown as molecularly thin 2D organic crystals. The dielectric constants of the CL-v phase range from 4.8 to 5.5 and we demonstrate their potential as gate dielectrics for thin-film transistors.

Understanding the effects of A-site Ag-doping on LaCoO3 perovskite for NO oxidation: Structural and magnetic properties

The partial substitution of A-site in perovskites is a major strategy to enhance the catalytic oxidation activity. This study explores the use of silver (Ag) to partially replace the lanthanum (La) ion at the A-site in LaCoO3 perovskite, investigating the role of Ag in the ABO3 perovskite structure, elucidating the nitric oxide (NO) oxidation mechanism over La1-xAgxCoO3 (x = 0.1-0.5) perovskites. La0.7Ag0.3CoO3 with an Ag-doping amount of 0.3, exhibited the highest NO oxidation activity of 88.5% at 275 °C. Characterization results indicated that Ag substitution enhanced the perovskite, maintaining its original phase structure, existing in the form of a mixture of Ag0 and Ag+ in the La1-xAgxCoO3 (x = 0.1-0.5) perovskites. Notably, Ag substitution improved the specific surface area, reduction performance, Co3+, and surface adsorption oxygen content. Additionally, the study investigated the relationship between magnetism and NO oxidation from a magnetism perspective. Ag-doping strengthened the magnetism of La-Ag perovskite, resulting in stronger adsorption of paramagnetic NO. This study elucidated the NO oxidation mechanism over La-Ag perovskite, considering structural and magnetic properties, providing valuable insights for the subsequent development and industrial application of high oxidation ability perovskite catalysts.

Competing double-exchange/super-exchange ordering for enhanced water oxidation kinetics

Competing double-exchange and super-exchange interactions yield rich chemistry for understanding robust oxygen evolution activity in Ru-doped lanthanum strontium manganite, with an overpotential of 300 mV at 10 mA cm-2 and a Tafel slope of 110 mV dec-1. Favourable redox potentials of Mn3+/Mn4+ and Ru4+/Ru5+ lead to improved charge transfer kinetics for OER activity.

Perovskites as oxygen storage materials for chemical looping partial oxidation and reforming of methane

The traditional partial oxidation, dry reforming and steam reforming of methane technologies are separated into two reactors for execution by chemical looping technology, which can avoid the defects exposed in the traditional process (avoiding carbon accumulation, reducing costs, etc.). The key to chemical looping technology is to find suitable oxygen carriers (OCs), which can store and release oxygen to form a closed loop in the chemical looping. The purpose of this review is to summarize the current status of perovskite oxides for partial oxidation and reforming of methane in chemical looping, describe the structure, oxygen capacity, oxygen migration rate and common synthesis methods of perovskites in chemical looping. In addition, the effects of impregnation loading, ion doping, and structural morphology on the catalytic conversion of CH4 by perovskite OCs and the reaction mechanism on the OCs are also discussed.

Methanol assisted water electrooxidation on noble metal free perovskite: RRDE insight into the catalyst's behaviour

In this work, we have hypothesized that noble metal-free perovskites are an essential class of oxygen evolution reaction (OER) catalysts in an alkaline medium and thus, they are a suitable candidate for the assisted water oxidation catalysts. Herein, we demonstrate that the origin of the methanol-assisted OER activity at near thermodynamic potential on perovskite electrode arises due to the involvement of additional hydroxyls as a result of dissociative chemisorption of methanol. When the perovskite electrode is screened for methanol electrooxidation reaction in 0.5 M KOH + 0.5 M methanol electrolyte, it delivers a two times higher current density. This imparts an 82 % increase in the evolution of oxygen gas moles with complete oxidation of methanol to carbon dioxide. Along with the electrochemical characterization to understand the electrocatalyst property, Rotating ring disk electrode (RRDE) technique is explored for the first time in literature to validate the catalyst's involvement during OER. RRDE is effective in understanding the lattice oxygen behaviour and methanol-assisted water electrooxidation during OER. Our results suggest new insights and ideas towards the oxygen evolution reaction process and the mechanistic insight into the elevated OER due to assisted methanol electrooxidation.

The Advances, Challenges, and Perspectives on Electrocatalytic Reduction of Nitrogenous Substances to Ammonia: A Review

Ammonia (NH3) is considered to be a critical chemical feedstock in agriculture, industry, and other fields. However, conventional Haber-Bosch (HB) ammonia (NH3) production suffers from high energy consumption, harsh reaction conditions, and large carbon dioxide emissions. Despite the emergence of electrocatalytic reduction of nitrogenous substances to NH3 under ambient conditions as a new frontier, there are several bottleneck problems that impede the commercialization process. These include low catalytic efficiency, competition with the hydrogen evolution reaction, and difficulties in breaking the N≡N triple bond. In this review, we explore the recent advances in electrocatalytic NH3 synthesis, using nitrogen and nitrate as reactants. We focus on the contribution of the catalyst design, specifically based on molecular-catalyst interaction mechanisms, as well as chemical bond breaking and directional coupling mechanisms, to address the aforementioned problems during electrocatalytic NH3 synthesis. Finally, we discuss the relevant opportunities and challenges in this field.

Study of S poisoning mechanism on LaMnO3 perovskite catalyst surface based on DFT method

The sulfur poisoning mechanism of low-temperature SCR de-NOx catalyst has always been one of the hot spots in academic circles. By studying the surface sulfur poisoning mechanism, low-temperature catalysts can be developed pertinently. In this paper, the mechanism of sulfur poisoning on the surface of LaMnO3 catalyst was studied by DFT method, and the adsorption process of sulfur oxides on the surface and its influence on SCR reaction process, as well as the morphology and decomposition process of ammonium sulfate on the surface were calculated. The results show that sulfur oxides will be adsorbed on the surface and occupy the adsorption site, which will adversely affect the subsequent SCR reaction. At the same time, ammonium sulfate will accumulate on the catalyst surface, which will lead to sulfur poisoning.

Strategies for improving the stability of perovskite for photocatalysis: A review of recent progress

Photocatalysis is currently a hot research field, which provides promising processes to produce green energy sources and other useful products, thus eventually benefiting carbon emission reduction and leading to a low-carbon future. The development and application of stable and efficient photocatalytic materials is one of the main technical bottlenecks in the field of photocatalysis. Perovskite has excellent performance in the fields of photocatalytic hydrogen evolution reaction (HER), oxygen evolution reaction (OER), carbon dioxide reduction reaction (CO2RR), organic synthesis and pollutant degradation due to its unique structure, flexibility and resulting excellent photoelectric and catalytic properties. The stability problems caused by perovskite's susceptibility to environmental influences hinder its further application in the field of photocatalysis. Therefore, this paper innovatively summarizes and analyzes the existing methods and strategies to improve the stability of perovskite in the field of photocatalysis. Specifically, (i) component engineering, (ii) morphological control, (iii) hybridization and encapsulation are thought to improve the stability of perovskites while improving photocatalytic efficiency. Finally, the challenges and prospects of perovskite photocatalysts are discussed, which provides constructive thinking for the potential application of perovskite photocatalysts.

Screening Ba0.9A0.1MnO3 and Ba0.9A0.1Mn0.7Cu0.3O3 (A = Mg, Ca, Sr, Ce, La) Sol-Gel Synthesised Perovskites as GPF Catalysts

Ba0.9A0.1MnO3 (BM-A) and Ba0.9A0.1Mn0.7Cu0.3O3 (BMC-A) (A = Mg, Ca, Sr, Ce, La) perovskite-type mixed oxides were synthesised, characterised, and used for soot oxidation in simulated Gasoline Direct Injection (GDI) engine exhaust conditions. The samples have been obtained by the sol-gel method in an aqueous medium and deeply characterised. The characterization results indicate that the partial substitution of Ba by A metal in BaMnO3 (BM) and BaMn0.7Cu0.3O3 (BMC) perovskites: (i) favours the hexagonal structure of perovskite; (ii) improves the reducibility and the oxygen desorption during Temperature-Programmed Desorption (O2-TPD) tests and, consequently, the oxygen mobility; (iii) mantains the amount of oxygen vacancies and of Mn(IV) and Mn(III) oxidation states, being Mn(IV) the main one; and (iv) for Ba0.9A0.1Mn0.7Cu0.3O3 (BMC-A) series, copper is partially incorporated into the structure. The soot conversion data reveal that Ba0.9La0.1Mn0.7Cu0.3O3 (BMC-La) is the most active catalyst in an inert (100% He) reaction atmosphere, as it presents the highest amount of copper on the surface, and that Ba0.9Ce0.1MnO3 (BM-Ce) is the best one if a low amount of O2 (1% O2 in He) is present, as it combines the highest emission of oxygen with the good redox properties of Ce(IV)/Ce(III) and Mn(IV)/Mn(III) pairs.

Electronic Structure of Small Isolated and Supported Manganese Oxide Clusters

In the present work, possible molecular models of the isolated manganese oxides and supported Mn3Ox/Al2O3 structures were built based on small clusters of passivated MnOx. The support was represented as a simplified model of the alumina tetramer cluster based on small fragments of AlOxHy. Combinations of MnOxHy and AlOxHy clusters were made to form both the isolated and supported manganese oxides clusters. The electronic structure of these systems was characterized by ab initio methods (DFT and CASPT2). It was observed that the vertical excitation energy of the isolated and supported Mn3OxHy clusters is significantly lower than that of the alumina cluster model, while both the isolated and supported Mn3OxHy wave function characters are qualitatively similar with respect to the ground state and electronic transition processes, suggesting that the alumina cluster behaves as an inert support, since there is little contribution of this component in the description of the low-lying electronic states. The present study also reports for the first time the spectroscopic parameters of several clusters containing the manganese transition metal atom.

Dry reforming of methane over gallium-based supported catalytically active liquid metal solutions

Gallium-rich supported catalytically active liquid metal solutions (SCALMS) were recently introduced as a new way towards heterogeneous single atom catalysis. SCALMS were demonstrated to exhibit a certain resistance against coking during the dehydrogenation of alkanes using Ga-rich alloys of noble metals. Here, the conceptual catalytic application of SCALMS in dry reforming of methane (DRM) is tested with non-noble metal (Co, Cu, Fe, Ni) atoms in the gallium-rich liquid alloy. This study introduces SCALMS to high-temperature applications and an oxidative reaction environment. Most catalysts were shown to undergo severe oxidation during DRM, while Ga-Ni SCALMS retained a certain level of activity. This observation is explained by a kinetically controlled redox process, namely oxidation to gallium oxide species and re-reduction via H2 activation over Ni. Consequentially, this redox process can be shifted to the metallic side when using increasing concentrations of Ni in Ga, which strongly suppresses coke formation. Density-functional theory (DFT) based ab initio molecular dynamics (AIMD) simulations were performed to confirm the increased availability of Ni at the liquid alloy-gas interface. However, leaching of gallium via the formation of volatile oxidic species during the hypothesised redox cycles was identified indicating a critical instability of Ga-Ni SCALMS for prolonged test durations.

Ca substitution improves the catalytic activity of perovskite LaCoO3 toward toluene: comprehension of electronic structure alteration

For perovskite La1-xCaxCoO3 (Ca-x, x = 0-0.3), Ca-0.2 with the closest O p band center to the Fermi level, displays the best catalytic activity for toluene oxidation. The O p band center determines the reducibility and active oxygen content. This finding is beneficial for the design of highly active perovskite catalysts.

Hydrogen-Rich Gas Production by Steam Reforming and Oxidative Steam Reforming of Methanol over La0.6Sr0.4CoO3-δ: Effects of Preparation, Operation Conditions, and Redox Cycles

La0.6Sr0.4CoO3-δ (LSC) perovskite, as a potential catalyst precursor for hydrogen (H2)-rich production by steam reforming of methanol (SRM) and oxidative steam reforming of methanol (OSRM), was investigated. For this purpose, LSC was synthesized by the citrate sol-gel method and characterized by complementary analytical techniques. The catalytic activity was studied for the as-prepared and prereduced LSC and compared with the undoped LaCoO3-δ (LCO) at several feed gas compositions. Furthermore, the degradation and regeneration of LSC under repeated redox cycles were studied. The results evidenced that the increase in the water/methanol ratio under SRM, and the O2 addition under OSRM, increased the CO2 formation and decreased both the H2 selectivity and catalyst deactivation caused by carbon deposition. Methanol conversion of the prereduced LSC was significantly enhanced at a lower temperature than that of as-prepared LSC and undoped LCO. This was attributed to the performance of metallic cobalt nanoparticles highly dispersed under reducing atmospheres. The reoxidation program in repetitive redox cycles played a crucial role in the regeneration of catalysts, which could be regenerated to the initial perovskite structure under a specific thermal treatment, minimizing the degradation of the catalytic activity and surface.

Methane Catalytic Combustion under Lean Conditions over Pristine and Ir-Loaded La1-xSrxMnO3 Perovskites: Efficiency, Hysteresis, and Time-on-Stream and Thermal Aging Stabilities

The increasing use of natural gas as an efficient, reliable, affordable, and cleaner energy source, compared with other fossil fuels, has brought the catalytic CH4 complete oxidation reaction into the spotlight as a simple and economic way to control the amount of unconverted methane escaping into the atmosphere. CH4 emissions are a major contributor to the 'greenhouse effect', and therefore, they need to be effectively reduced. Catalytic CH4 oxidation is a promising method that can be used for this purpose. Detailed studies of the activity, oxidative thermal aging, and the time-on-stream (TOS) stability of pristine La1-xSrxMnO3 perovskites (LSXM; X = % substitution of La with Sr = 0, 30, 50 and 70%) and iridium-loaded Ir/La1-xSrxMnO3 (Ir/LSXM) perovskite catalysts were conducted in a temperature range of 400-970 °C to achieve complete methane oxidation under excess oxygen (lean) conditions. The effect of X on the properties of the perovskites, and thus, their catalytic performance during heating/cooling cycles, was studied using samples that were subjected to various pretreatment conditions in order to gain an in-depth understanding of the structure-activity/stability correlations. Large (up to ca. 300 °C in terms of T50) inverted volcano-type differences in catalytic activity were found as a function of X, with the most active catalysts being those where X = 0%, and the least active were those where X = 50%. Inverse hysteresis phenomena (steady-state rate multiplicities) were revealed in heating/cooling cycles under reaction conditions, the occurrence of which was found to depend strongly on the employed catalyst pre-treatment (pre-reduction or pre-oxidation), while their shape and the loop amplitude were found to depend on X and the presence of Ir. All findings were consistently interpreted, which involved a two-term mechanistic model that utilized the synergy of Eley-Rideal and Mars-van Krevelen kinetics.

Boosting CO2 Electroreduction to C2H4 via Unconventional Hybridization: High-Order Ce4+ 4f and O 2p Interaction in Ce-Cu2O for Stabilizing Cu. ACS NANO 2023. [PMID: 37410800 DOI: 10.1021/acsnano.3c03952]

Efficient conversion of carbon dioxide (CO₂) into value-added materials and feedstocks, powered by renewable electricity, presents a promising strategy to reduce greenhouse gas emissions and close the anthropogenic carbon loop. Recently, there has been intense interest in Cu₂O-based catalysts for the CO₂ reduction reaction (CO₂RR), owing to their capabilities in enhancing C-C coupling. However, the electrochemical instability of Cu⁺ in Cu₂O leads to its inevitable reduction to Cu⁰, resulting in poor selectivity for C₂₊ products. Herein, we propose an unconventional and feasible strategy for stabilizing Cu⁺ through the construction of a Ce⁴⁺ 4f-O 2p-Cu⁺ 3d network structure in Ce-Cu₂O. Experimental results and theoretical calculations confirm that the unconventional orbital hybridization near E_f based on the high-order Ce⁴⁺ 4f and 2p can more effectively inhibit the leaching of lattice oxygen, thereby stabilizing Cu⁺ in Ce-Cu₂O, compared with traditional d-p hybridization. Compared to pure Cu₂O, the Ce-Cu₂O catalyst increased the ratio of C₂H₄/CO by 1.69-fold during the CO₂RR at -1.3 V. Furthermore, in situ and ex situ spectroscopic techniques were utilized to track the oxidation valency of copper under CO₂RR conditions with time resolution, identifying the well-maintained Cu⁺ species in the Ce-Cu₂O catalyst. This work not only presents an avenue to CO₂RR catalyst design involving the high-order 4f and 2p orbital hybridization but also provides deep insights into the metal-oxidation-state-dependent selectivity of catalysts.

Single-atom Pt-CeO2/Co3O4 catalyst with ultra-low Pt loading and high performance for toluene removal

The design and manufacture of high activity and thermal stability catalysts with minimal precious metal loading is essential for deep degradation of volatile organic compounds (VOCs). In this paper, a novel single-atom Pt-CeO₂/Co₃O₄ catalyst with ultra-low Pt loading capacity (0.06 wt%, denoted as 0.06Pt-SA) was fabricated via one-step co-precipitation method. The 0.06Pt-SA exhibited excellent toluene degradation activity of T₉₀ = 169 °C, matched with the nanoparticle Pt-supported CeO₂/Co₃O₄ catalyst with more than six times higher Pt loading (0.41 wt%, denoted as 0.41Pt-NP). Moreover, the ultra-long durability (toluene conversion remains 99% after 120 h stability test) and excellent toluene degradation ability in a wide space speed range of 0.06Pt-SA were superior to that of 0.41Pt-NP catalyst. The excellent performance was derived from the strong metal-support interaction (SMSI) between the single atomic Pt and the carrier, which induced more Pt⁰ and Ce³⁺ for oxygen activation and more Co³⁺ for toluene removal. The in situdiffuse reflectance infrared spectroscopy (DRIFTS) experiments confirmed that the conversion of intermediates was accelerated in the reaction process, thereby promoting the toluene degradation. Our results should inspire the exploitation of noble single-atomic modification strategy for developing the low cost and high performance VOCs catalyst.

Lattice-charge imbalance and redox catalysis over perovskite-type ferrite- and manganite-based mixed oxides as studied by XRD, FTIR, UV-Vis DRS, and XPS

In the present investigation, two sets of pure and substituted ferrite- and manganite-based mixed oxides were prepared within the stoichiometric formula[Formula: see text], where A = Bi or La, A^' = Sr, B = Fe or Mn, B' = Co, x = 0 or 0.2, by calcination at 700 °C (for 1 h) of corresponding metal citrate xerogels. Materials thus obtained were examined for bulk and surface characteristics using X-ray diffractometry, ex situ Fourier transform infrared spectroscopy, UV-Vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, and N₂ sorptiometry. Their redox catalytic activity was evaluated towards a 2-propanol dehydrogenation reaction in the gas phase by employing in situ Fourier transform infrared spectroscopy. The results obtained could help reveal that (1) the presence of Bi (versus La) and Mn (versus Fe) facilitated the formation of polymeric crystalline phases assuming lattice-charge imbalance (due to excess positive charge), (2) the surface exposure of the excess positive charge was manifested in the generation of Mn sites having various oxidation states ≥ 3+, (3) the consequent development of visible light absorptions at 498-555 nm suggested occurrence of electron double-exchange facilitated by the formation of Mnⁿ⁺-O^2--Mn⁽ⁿ⁺¹⁾⁺ Zener-type linkages, and (4) the exposure of such linkages at the surface warrants the establishment of the electron-mobile environment necessitated by the redox catalytic activity. Moreover, the relationship between the alcohol dehydrogenation activity and the magnitude of the lattice-charge imbalance (i.e., the net excess positive charge) of the catalysts was highlighted.

Enhancement of toluene oxidation performance over La1-xCoO3-δ perovskite by lanthanum non-stoichiometry

La_1-xCoO_3-δ catalysts with different non-stoichiometry of lanthanum ions were synthesized by using the sol-gel method, and their catalytic performance in toluene combustion was investigated. The results showed that the catalytic activity and stability of A-site nonstoichiometric La_1-xCoO_3-δ were improved to a certain extent compared with pure LaCoO₃ perovskite. Among them, the La_0.9CoO_3-δ catalyst gave the best catalytic performance for toluene oxidation. It achieved 90% toluene conversion at 205°C under the conditions of a WHSV (weight hourly space velocity) of 22,500 mL/(g·hr) and a 500 ppmV-toluene concentration. Various characterization techniques were used to investigate the relationship between the structure of these catalysts and their catalytic performance. It was found that the non-stoichiometric modification of the lanthanum ion at position A in LaCoO₃ changed the surface element state of the catalyst and increased the oxygen vacancy content, thus, combined with improved reducibility, improving toluene degradation on the catalyst.

A Visible-Light-Enhanced Heterogeneous Photo Degradation of Tetracycline by a Nano-LaFeO3 Catalyst with the Assistance of Persulfate

Perovskites with nano-flexible texture structures and excellent catalytic properties have attracted considerable attention for persulfate activation in addressing the organic pollutants in water. In this study, highly crystalline nano-sized LaFeO₃ was synthesized by a non-aqueous benzyl alcohol (BA) route. Under optimal conditions, an 83.9% tetracycline (TC) degradation and 54.3% mineralization were achieved at 120 min by using a coupled persulfate/photocatalytic process. Especially compared to LaFeO₃-CA (synthesized by a citric acid complexation route), the pseudo-first-order reaction rate constant increased by 1.8 times. We attribute this good degradation performance to the highly specific surface area and small crystallite size of the obtained materials. In this study, we also investigated the effects of some key reaction parameters. Then, the catalyst stability and toxicity tests were also discussed. The surface sulfate radicals were identified as the major reactive species during the oxidation process. This study provided a new insight into nano-constructing a novel perovskite catalyst for the removal of tetracycline in water.

Nanosized Ti-Based Perovskite Oxides as Acid-Base Bifunctional Catalysts for Cyanosilylation of Carbonyl Compounds

The development of effective solid acid-base bifunctional catalysts remains a challenge because of the difficulty associated with designing and controlling their active sites. In the present study, highly pure perovskite oxide nanoparticles with d⁰-transition-metal cations such as Ti⁴⁺, Zr⁴⁺, and Nb⁵⁺ as B-site elements were successfully synthesized by a sol-gel method using dicarboxylic acids. Moreover, the specific surface area of SrTiO₃ was increased to 46 m² g^-1 by a simple procedure of changing the atmosphere from N₂ to air during calcination of an amorphous precursor. The resultant SrTiO₃ nanoparticles showed the highest catalytic activity for the cyanosilylation of acetophenone with trimethylsilyl cyanide (TMSCN) among the tested catalysts not subjected to a thermal pretreatment. Various aromatic and aliphatic carbonyl compounds were efficiently converted to the corresponding cyanohydrin silyl ethers in good-to-excellent yields. The present system was applicable to a larger-scale reaction of acetophenone with TMSCN (10 mmol scale), in which 2.06 g of the analytically pure corresponding product was isolated. In this case, the reaction rate was 8.4 mmol g^-1 min^-1, which is the highest rate among those reported for heterogeneous catalyst systems that do not involve a pretreatment. Mechanistic studies, including studies of the catalyst effect, Fourier transform infrared spectroscopy, and temperature-programmed desorption measurements using probe molecules such as pyridine, acetophenone, CO₂, and CHCl₃, and the poisoning effect of pyridine and acetic acid toward the cyanosilylation, revealed that moderate-strength acid and base sites present in moderate amounts on SrTiO₃ most likely enable SrTiO₃ to act as a bifunctional acid-base solid catalyst through cooperative activation of carbonyl compounds and TMSCN. This bifunctional catalysis through SrTiO₃ resulted in high catalytic performance even without a heat pretreatment, in sharp contrast to the performance of basic MgO and acidic TiO₂ catalysts.

Role of La-based perovskite catalysts in environmental pollution remediation

Since the advent of the industrial revolution, there has been a constant need of efficient catalysts for abatement of industrial toxic pollutants. This phenomenon necessitated the development of eco-friendly, stable, and economically feasible catalytic materials like lanthanum-based perovskite-type oxides (PTOs) having well-defined crystal structure, excellent thermal, and structural stability, exceptional ionic conductivity, redox behavior, and high tunability. In this review, applicability of La-based PTOs in remediation of pollutants, including CO, NO x and VOCs was addressed. A framework for rationalizing reaction mechanism, substitution effect, preparation methods, support, and catalyst shape has been discussed. Furthermore, reactant conversion efficiencies of best PTOs have been compared with noble-metal catalysts for each application. The catalytic properties of the perovskites including electronic and structural properties have been extensively presented. We highlight that a robust understanding of electronic structure of PTOs will help develop perovskite catalysts for other environmental applications involving oxidation or redox reactions.

CeO2 supported MOFs derived LaBxFeyO3 (B=Mn, Co) perovskite catalysts for degradation of toluene

In this work, LaCoO₃ and LaMnO₃ perovskites with the higher specific surface area were synthesized using MOFs as precursor, then, the composite catalysts CeO₂-LaCo_xFe_yO₃ and CeO₂-LaMn_xFe_yO₃ were prepared by using CeO₂ as support and Fe element doping LaCoO₃ and LaMnO₃, respectively. The as-prepared samples were characterized by XRD, SEM, XPS, H₂-TPR, and N₂ physisorption techniques. Subsequently, toluene was used as the probe molecule for volatile organic compounds (VOCs) to test the catalytic activity of these as-prepared catalysts. The results show that the initial reaction temperature for toluene oxidation on supported perovskite catalysts is lower. Among which, CeO₂-LaCo_0.25Fe_0.75O₃ (T₉₀=215 °C, T₉₀: the temperature corresponding to 90% conversion of toluene) and CeO₂-LaMn_0.25Fe_0.75O₃ (T₉₀=205 °C) catalysts show the best catalytic performance. Therefore, the supported perovskite prepared in this study has the advantages of high specific surface area, abundant oxygen vacancies, and excellent oxygen mobility, which makes it exhibit better performance in VOCs catalytic oxidation.

Stepping Up the Kinetics of Li-O2 Batteries by Shrinking Down the Li2O2 Granules through Concertedly Enhanced Catalytic Activity and Photoactivity of Se-Doped LaCoO3

Owing to their structural tunability for furnishing high catalytic activity and photoactivity, perovskite oxides are a class of promising materials for high-performance photocathode catalysts in a photoassisted lithium oxygen battery (LOB), which is still in its infancy. Herein, single-crystalline LaCoO3 (LCO) is successfully synthesized through a microwave-assisted approach and selenylated to simultaneously introduce anionic doping and oxygen vacancies, boosting not only the electrocatalytic activity toward reversible Li2O2 formation/decomposition, but also the photoactivity to further reduce the charge/discharge polarization. As a result, LOBs utilizing Se-doped LCO as the photocathode catalyst demonstrate a superior performance under illumination in all aspects of energy efficiency, specific capacity, and cycling stability, ranking among the best reported in the literature for perovskite oxides. The photoenhanced charge kinetics is found to be correlated with the accelerated Li2O2 nucleation with lowered granule size, which is key to both the improved charge/discharge capacity and reversibility. The results underscore the tailoring of perovskite structure to aggrandize both the catalytic activity and photoactivity for concertedly promoting the kinetics of LOBs.

Activity and Thermal Aging Stability of La1-xSrxMnO3 (x = 0.0, 0.3, 0.5, 0.7) and Ir/La1-xSrxMnO3 Catalysts for CO Oxidation with Excess O2

The catalytic oxidation of CO is probably the most investigated reaction in the literature, for decades, because of its extended environmental and fundamental importance. In this paper, the oxidation of CO on La_1-xSr_xMnO₃ perovskites (LSMx), either unloaded or loaded with dispersed Ir nanoparticles (Ir/LSMx), was studied in the temperature range 100-450 °C under excess O₂ conditions (1% CO + 5% O₂). The perovskites, of the type La_1-xSr_xMnO₃ (x = 0.0, 0.3, 0.5 and 0.7), were prepared by the coprecipitation method. The physicochemical and structural properties of both the LSMx and the homologous Ir/LSMx catalysts were evaluated by various techniques (XRD, N₂ sorption-desorption by BET-BJH, H₂-TPR and H₂-Chem), in order to better understand the structure-activity-stability correlations. The effect of preoxidation/prereduction/aging of the catalysts on their activity and stability was also investigated. Results revealed that both LSMx and Ir/LSMx are effective for CO oxidation, with the latter being superior to the former. In both series of materials, increasing the substitution of La by Sr in the composition of the perovskite resulted to a gradual suppression of their CO oxidation activity when these were prereduced; the opposite was true for preoxidized samples. Inverse hysteresis phenomena in activity were observed during heating/cooling cycles on the prereduced Ir/LSMx catalysts with the loop amplitude narrowing with increasing Sr-content in LSMx. Oxidative thermal sintering experiments at high temperatures revealed excellent antisintering behavior of Ir nanoparticles supported on LSMx, resulting from perovskite's favorable antisintering properties of high oxygen storage capacity and surface oxygen vacancies.

Recent Status and Developments of Vacancies Modulation in the ABO3 Perovskites for Catalytic Applications

Perovskite oxides (ABO₃ ) have attracted comprehensive interest for wide range of functional applications (especially for chemical catalysis) due to their high design flexibility, controllable vacancies sites creation, abundant chemical properties, and stable crystal structure. Herein, the previous research and potential development of ABO₃ through adjusting the vacancy at different sites (A-site, B-site, and O-site) to enhance catalytic performance are systematically analyzed and generalized. Briefly, the ABO₃ with different vacancies sites prepared by multifarious direct and indirect methods, accompanied with the improved physical-chemical properties, endow them with distinct and intensified development of catalysis application. In addition, the impressive optimization proved by the vacancies sites adjustment over the ABO₃ is studied to continuously facilitate the advance in some common catalysis reactions, further expanding to other optimized functional applications. At last, the constructive suggestions for fine regulation and analysis of vacancies sites over ABO₃ are also put forward.

Effect of the Calcination Temperature of LaNiO3 on the Structural Properties and Reaction Performance of Catalysts in the Steam Reforming of Methane

The steam reforming of methane (SRM) reaction is a significant process for efficient syngas generation and for promising distributed hydrogen production. In this work, a series of LaNiO3 oxides were prepared using the Pechini method, calcined from 600 °C to 900 °C and tested for the SRM reaction. Fresh, reduced, and used samples were characterized using STA-MS-FTIR, in situ and ex situ XRD, N2 physical adsorption, H2-TPR, TEM, TPO, and Raman. The results show that LaNiO3 begins to crystallize at about 550 °C, and the increase in calcination temperature results in the following differences in the properties of the LaNiO3 samples: larger LaNiO3 grains, smaller specific surface area, higher reduction temperature, smaller Ni0 grains reduced from the bulk phase, and stronger metal–support interaction. The maximum CH4 conversion could be achieved over LaNiO3 calcinated at 800 °C. In addition, the effect of steam-to-carbon ratio (S/C) on the performance of the SRM reaction was studied, and a S/C of 1.5 was found to be optimal for CH4 conversion. Too strong a metal–support interaction and too much unreacted steam causes a loss of catalytic activity. Finally, it was also proved using TPO and Raman that an increase in calcination temperature improves the carbon deposition resistance of the catalyst.

Phase Transition of High-Surface-Area Glycol-Thermal Synthesized Lanthanum Manganite

Cubic and rhombohedral phases of lanthanum manganite were synthesized in a high-pressure reactor. A mixture of La and Mn nitrates with ethylene glycol at a synthesis temperature of 200 °C and a calcination temperature of up to 1000 °C, resulted in a single-phase perovskite, LaMnO₃ validated using X-ray diffraction. Significant changes in unit cell volumes from 58 to 353 ų were observed associated with structural transformation from the cubic to the rhombohedral phase. This was confirmed using structure calculations and resistivity measurements. Transmission electron microscopy analyses showed small particle sizes of approximately 19, 39, 45, and 90 nm (depending on calcination temperature), no agglomeration, and good crystallinity. The particle characteristics, high purity, and high surface area (up to 33.1 m²/g) of the material owed to the inherent PAAR reactor pressure, are suitable for important technological applications, that include the synthesis of perovskite oxides. Characteristics of the synthesized LaMnO₃ at different calcination temperatures are compared, and first-principles calculations suggest a geometric optimization of the cubic and rhombohedral perovskite structures.

Reactivity of Lattice Oxygen in Ti-Site-Substituted SrTiO3 Perovskite Catalysts

An environmental catalyst in which a transition metal (Mn, Fe, or Co) was substituted into the Ti site of the host material, SrTiO₃, was synthesized, and the reactivity of lattice oxygen was evaluated. For CO oxidation, Mn- and Co-doped SrTiO₃ catalysts, which provided high thermal stabilities, exhibited higher activities than Pt/Al₂O₃ catalysts despite their low surface areas. Temperature-programmed reduction experiments using X-ray absorption fine structure (XAFS) measurements showed that the lattice oxygen of Co-doped catalyst was released at the lowest temperature. Isotopic experiments with CO and ¹⁸O₂ revealed that the lattice oxygen was involved in CO oxidation on Fe- and Co-doped catalysts; that is, CO oxidation on these catalysts proceeded via the Mars-van Krevelen mechanism. On the other hand, for Mn-doped catalyst, the contribution of lattice oxygen to CO oxidation was relatively negligible, indicating that the reaction proceeded according to the Langmuir-Hinshelwood mechanism. This paper clearly demonstrates that the catalytic mechanism can be adjusted by substituting transition metals into SrTiO₃.

Etching-Induced Surface Reconstruction of NiMoO4 for Oxygen Evolution Reaction

Rational reconstruction of oxygen evolution reaction (OER) pre-catalysts and performance index of OER catalysts are crucial but still challenging for universal water electrolysis. Herein, we develop a double-cation etching strategy to tailor the electronic structure of NiMoO4, where the prepared NiMoO4 nanorods etched by H2O2 reconstruct their surface with abundant cation deficiencies and lattice distortion. Calculation results reveal that the double cation deficiencies can make the upshift of d-band center for Ni atoms and the active sites with better oxygen adsorption capacity. As a result, the optimized sample (NMO-30M) possesses an overpotential of 260 mV at 10 mA cm-2 and excellent long-term durability of 162 h. Importantly, in situ Raman test reveals the rapid formation of high-oxidation-state transition metal hydroxide species, which can further help to improve the catalytic activity of NiMoO4 in OER. This work highlights the influence of surface remodification and shed some light on activating catalysts.

Supported Mn2O3-based catalysts for NO-SCO: an experimental study

In this paper, the NO-SCO (the selective catalytic oxidation of NO) experiments of single-phase Mn₂O₃, supported Mn₂O₃/Al₂O₃, and the Ce-doped Mn_xCe_y/Al catalyst system were carried out. The physical and chemical properties of the catalysts were analyzed by XRD, BET, XPS, SEM, O₂-TPD, and H₂-TPR. The effects of loading and Ce doping on catalyst activity were studied. The results show that the Mn₂O₃ catalyst exhibited the best activity at 300 ℃, and the NO conversion rate of Mn₂O₃ was 78.2%. The relative content of O_α adsorbed on the surface of the Mn_x/Al catalyst decreased obviously by loading Mn₂O₃ on γ-Al₂O₃, which led to the decrease in catalyst activity. And the temperature window moved to the high-temperature region. After doping Ce, the dispersion of Mn enhanced, and the relative content of oxygen O_α adsorbed on the surface increased. The low-temperature activity and fluidity of oxygen in catalysts were improved. Among them, the Mn_0.2Ce_0.08/Al catalyst obtained a high specific surface area, good pore structure, large oxygen storage capacity, and excellent surface oxygen species. The corresponding NO conversion rate reached 83.5% at 290 ℃. Then, the effects of operating parameters such as space velocity, NO concentration, and O₂ content on the catalytic activity of Mn_0.2Ce_0.08/Al were discussed. The experimental results show that the NO conversion rate of Mn_0.2Ce_0.08/Al decreased with increasing NO concentration and space velocity. The O₂ content had a positive effect on the catalytic activity of the catalyst. However, the NO conversion rate tended to be stable due to the saturation of oxygen adsorbed on the catalyst. Through cycling experiments, we found that Mn₂O₃, Mn_0.2/Al, and Mn_0.2Ce_0.08/Al catalysts showed good oxidation stabilities for NO oxidation. The evaluation of the water and sulfur resistance of the catalyst shows that the toxicity of SO₂ was reduced by the aqueous atmosphere to a certain extent. Through the structural optimization of the basic model and the calculation of the NO-SCO reaction path, the results show that the NO-SCO reaction on the Mn₂O₃ (110) face followed the ER mechanism more. For the Mn₂O₃/Al₂O₃ (110) surface, the LH-MvK hybrid mechanism can greatly reduce the desorption energy barrier of the reaction intermediates, which is more favorable for the NO-SCO reaction. The catalytic mechanisms of the Mn_xCe_y/Al catalysts require further in-depth research.

Influences of Co-Content on the Physico-Chemical and Catalytic Properties of Perovskite GdCoxFe1−xO3 in CO Hydrogenation

The effect of the substitution of cobalt into the GdFeO3 perovskite structure on the selective hydrogenation of CO was investigated. A series of GdCoxFe1−xO3 (x = 0; 0.2; 0.5; 0.8; 1) samples were synthesized by sol-gel technology and characterized by XRD, BET specific area, DSC, TG, EDX and XPS. The experimental data made it possible to reveal a correlation between the state of iron and cobalt atoms, the fractions of surface and lattice oxygen, and catalytic characteristics. It has been found that varying the composition of GdCoxFe1−xO3 complex oxides leads to a change in the oxygen-metal binding energy in Gd-O-Me, the ratio of metals in various oxidation states, and the amount of surface and lattice oxygen, which affects the adsorption and catalytic characteristics of complex oxides.

Catalytic Degradation of Toluene over MnO2/LaMnO3: Effect of Phase Type of MnO2 on Activity

Series of α, β, γ, δ type MnO2 supported on LaMnO3 perovskite was developed by a one-pot synthesis route. Compared with α-MnO2, β-MnO2, γ-MnO2, δ-MnO2 and LaMnO3 oxides, all MnO2/LaMnO3 showed promotional catalytic performance for toluene degradation. Among them, α-MnO2/LaMnO3 holds the best active and mineralization efficiency. By the analysis of N2 adsorption-desorption, XPS and H2-TPR, it can be inferred that the improved activity should be ascribed to the higher proportion of lattice oxygen, better low-temperature reducibility and larger specific surface area. Besides, the byproducts from the low-temperature reaction of toluene oxidation were detected by a TD/GC-MS, confirming the presence of the intermediates. Combined with the in-situ DRIFTS, the catalytic degradation path of toluene oxidation has also been discussed in depth.

Supercritical fluid-assisted modification combined with the resynthesis of SmCoO3 as an effective tool to enhance the long-term performance of SmCoO3-derived catalysts for the dry reforming of methane to syngas

The dry reforming of methane to syngas (DRM) is of increasing significance concerning, first, the production of raw materials for commercial organic/petrochemical syntheses and for hydrogen energetic, and, second, the utilization of two most harmful greenhouse gases. Herein, new SmCoO₃-based DRM catalysts derived from heterometallic precursors and operated without preliminary reduction are reported. For the first time, the effect of supercritical fluids-assisted modification of the SmCoO₃-derived catalysts combined with the re-oxidation of spent catalysts to SmCoO₃ onto its long-term performance was studied. In particular, the modification of heterometallic precursors by supercritical antisolvent precipitation (SAS) considerably decreases coke formation upon the exploitation of the derived SmCoO₃ sample. Moreover, the re-oxidation of the corresponding spent catalysts followed by pre-heating under N₂ affords catalysts that stably provide syngas yields of 88-95% for at least 41 h at 900 °C. The achieved yields are among the highest ones currently reported for DRM catalysts derived from both LnMO₃ perovskites and related oxides. The origins of such good performance are discussed. Given the simplicity and availability of all the applied methods and chemicals, this result opens prospects for exploiting SAS in the design of efficient DRM catalysts.

Cr-Fe-Ni-Cu Quaternary Nanostructure as a Substitute for Precious Metals in Automotive Three-Way Catalysts

The replacement of precious metals (Rh, Pd, and Pt) in three-way catalysts with inexpensive and earth-abundant metal alternatives is an ongoing challenge. In this research, we examined various quaternary metal catalysts by selecting from six 3d transition metals, i.e., Cr, Mn, Fe, Co, Ni, and Cu, equimolar amounts (0.1 mol each), which were prepared on the Al2O3 support (1 mol Al) using H2 reduction treatment at 900 °C. Among 15 combinations, the best catalytic performance was achieved by the CrFeNiCu system. Light-off of NO-CO-C3H6-O2-H2O mixtures proceeded at the lowest temperature of ≤200 °C for CO, ≤300 °C for C3H6, and ≤400 °C for NO when the molar fraction of Cr in Cr x Fe0.1Ni0.1Cu0.1 was around x = 0.1. The activity for CO/C3H6 oxidation was superior to that of reference Pt/Al2O3 catalysts but was less active for NO reduction. The structural analysis using scanning transmission electron microscopy and X-ray absorption spectroscopy showed that the as-prepared catalyst consisted of FeNiCu alloy nanoparticles dispersed on the Cr2O3-Al2O3 support. However, the structural change occurred under a catalytic reaction atmosphere, i.e., producing NiCu alloy nanoparticles dispersed on a NiFe2O4 moiety and Cr2O3-Al2O3 support. The oxidation of CO/C3H6 can be significantly enhanced in the presence of Cr oxide, resulting in a faster decrease in O2 concentration and thus regenerating the NiCu metallic surface, which is active for NO reduction to N2.