Nature of Catalytic Active Sites Present on the Surface of Advanced Bulk Tantalum Mixed Oxide Photocatalysts

Design of Cr-Free Promoted Copper-Iron Oxide-Based High-Temperature Water-Gas Shift Catalysts

The effect of Ce addition to the Cr-free Al-promoted Cu-Fe oxide-based catalysts is investigated. Catalyst characterization (X-ray diffraction (XRD), in situ Raman spectroscopy, high-sensitivity low-energy ion scattering (HS-LEIS), Brunauer-Emmett-Teller (BET) analysis), CO-temperature-programmed reduction chemical probing, and steady-state WGS activity reveal that (i) in the absence of Al, Ce addition via coprecipitation has a detrimental effect on the catalytic activity related to the poor thermostability and formation of less active Ce-Cu-O NPs, (ii) the addition of Ce via coprecipitation also does not improve the performance of the CuAlFe catalyst because of the formation of a thick CeOx overlayer on the active Cu-FeOx interface, and (iii) impregnation of Ce onto the CuAlFe catalyst exhibits significant improvement in catalytic performance due to the formation of a highly active CeOx-FeOx-Cu interfacial area. In summary, Al does not surface-segregate and serves as a structural promoter, while Ce and Cu surface-segregate and act as functional promoters in Ce/CuAlFe mixed oxide catalysts.

Porous biomorphic silica@ZnO nanohybrids as the effective photocatalysts under visible light

In this study, zinc oxide nanohybrids based on functionalized bio-silica were synthesized and used for the degradation of Congo red under visible light. Diatom was used as a Si natural source with hierarchical nanostructures to produce porous silica support. Functionalized porous silica is a good candidate for direct immobilization of metal oxide and therefore of interest as the catalyst. Here, six hybrids of functionalized bio-silica and ZnO were synthesized and characterized by FT-IR, XRD, SEM/EDX, BET/BJH, and UV-Vis spectroscopy. Then, the synthesized catalysts were subjected to degradation of different anionic azo dyes (Congo red, methyl orange, and methyl red) under visible light irradiation. The results show the decrease of band gap in bio-silica@ZnO hybrids which enhance the photocatalytic properties of hybrids due to the shifting to visible light adsorption. The best photocatalytic result of SiO₂@ZnO hybrid was obtained from chitosan-based amino-functionalized silica due to the best functionalization, highest loading of ZnO, low band gap, and filling of diatom pores with functional groups.

Synthesis and molecular structure of model silica-supported tungsten oxide catalysts for oxidative coupling of methane (OCM)

Catalysts with only dispersed phase Na–WO₄ sites where Na/W < 2 are slightly less active but significantly more C₂ selective than the traditional Na₂WO₄/SiO₂ catalysts that contain a crystalline phase where Na/W = 2.

Enhanced photocatalysis and bacterial inhibition in Nb2O5 via versatile doping with metals (Sr, Y, Zr, and Ag): a critical assessment

Unique optical properties render semiconductor Nb₂O₅ nanoparticles suitable for light harvesting and photocatalytic applications. This study focuses on determining optical properties such as the band gap, conduction band edge, valence band edge and work function of as-prepared solution combustion synthesized Nb₂O₅ nanoparticles with the help of UV-vis Diffuse Reflectance spectroscopy (DRS) and ultraviolet photoelectron spectroscopy (UPS) techniques. Phase purity and the oxidation states of the elements present in the material were confirmed from X-ray diffraction (XRD) patterns and X-ray photoelectron spectra (XPS), respectively. Doping semiconductors with different metal ions impacts the activity of the material, and therefore efforts were made to understand the effect on the photocatalytic performance of Nb₂O₅ due to the incorporation of metal dopants viz. Sr, Y, Zr, and Ag. Lattice parameters were obtained from Rietveld refinement of the XRD patterns. Parameters which are closely related to the photoactivity of the catalysts such as the presence of surface defects, oxygen vacancies, surface area, and charge carrier dynamics were determined from photoluminescence (PL) analysis, Brunauer-Emmett-Teller (BET) surface area measurements and time-resolved fluorescence (TRF) analysis respectively. In addition, the dopant concentrations were optimised for enhanced photocatalytic activity. The doped Nb₂O₅ nanoparticles showed significant activity towards targeted degradation of organic pollutants like 2-chlorophenol (2-CP) and dye contaminants like methylene blue (MB), orange G (OG) and indigo carmine (IC). This strategy yielded a robust response towards inactivation of E. coli and S. aureus as well. Adsorption and photodegradation of MB followed Lagergren's pseudo 1^st order reaction model and the Langmuir Hinshelwood model respectively. Bacterial inactivation and OG, IC and 2-CP photodegradation followed 1^st order kinetics. The reusability of the catalyst for 5 cycles was demonstrated. Finally, a plausible mechanism is proposed based on radical trapping experiments and combined analysis of the characterization techniques.

Controlling Reaction Selectivity through the Surface Termination of Perovskite Catalysts

Although perovskites have been widely used in catalysis, tuning of their surface termination to control reaction selectivity has not been well established. In this study, we employed multiple surface-sensitive techniques to characterize the surface termination (one aspect of surface reconstruction) of SrTiO₃ (STO) after thermal pretreatment (Sr enrichment) and chemical etching (Ti enrichment). We show, by using the conversion of 2-propanol as a probe reaction, that the surface termination of STO can be controlled to greatly tune catalytic acid/base properties and consequently the reaction selectivity over a wide range, which is not possible with single-metal oxides, either SrO or TiO₂ . Density functional theory (DFT) calculations explain well the selectivity tuning and reaction mechanism on STO with different surface termination. Similar catalytic tunability was also observed on BaZrO₃ , thus highlighting the generality of the findings of this study.

CO2 reduction over NaNbO3 and NaTaO3 perovskite photocatalysts

Both NaNbO₃ and NaTaO₃ exhibit interesting intrinsic photocatalytic activities for CO₂ reduction in terms of conversion and selectivity.

Energetic stability, oxidation states, and electronic structure of Bi-doped NaTaO3: a first-principles hybrid functional study

We studied the defect formation energies, oxidation states of the dopants, and electronic structures of Bi-doped NaTaO3 using first-principles hybrid density functional theory calculations. Three possible structural models, including Bi-doped NaTaO3 with Bi at the Na site (Bi@Na), with Bi at the Ta site (Bi@Ta), and with Bi at both Na and Ta sites [Bi@(Na,Ta)], are constructed. Our results show that the preferred doping sites of Bi are strongly related to the preparation conditions of NaTaO3. It is energetically more favorable to form a Bi@Na structure under Na-poor conditions, to form a Bi@Ta structure under Na-rich conditions, and to form a Bi@(Na,Ta) structure under mildly Na-rich conditions. The Bi@Na doped model shows an n-type conducting character along with an expected blueshift of the optical absorption edge, in which the Bi atoms exist as Bi(3+) (6s(2)6p(0)). The Bi@Ta doped model has empty gap states consisting of Bi 6s states in its band gap, which can lead to visible-light absorption via the electron transition among the valence band, the conduction band, and the gap states. The Bi dopant is present as a Bi(5+) ion in this model, consistent with the experimental results. In contrast, the Bi@(Na,Ta) doped model has occupied gap states consisting of Bi 6s states in its band gap, and thus visible-light absorption is also expected in this system due to electron excitation from these occupied states to the conduction band, in which the Bi dopants exist as Bi(3+) ions. Our first-principles electronic structure calculations revealed the relationship between the Bi doping sites and the material preparation conditions, and clarified the oxidation states of Bi dopants in NaTaO3 as well as the origin of different visible-light photocatalytic hydrogen evolution behaviors in Bi@Ta and Bi@(Na,Ta) doped NaTaO3. This work can provide a useful reference for preparing a Bi-doped NaTaO3 photocatalyst with desired doping sites.

Effects of La-doping on charge separation behavior of ZnO:GaN for its enhanced photocatalytic performance

In this work, lanthanum (La) has been proven as an effective space charge layer modifier to promote efficient photogenerated charge carrier separation for ZnO:GaN solid solution photocatalysts with enhanced photocatalytic water-splitting performance.

Effect of Dopants on the Adsorption of Carbon Dioxide on Ceria Surfaces

High-surface-area nanosized CeO2 and M-doped CeO2 (M=Cu, La, Zr, and Mg) prepared by a surfactant-templated method were tested for CO2 adsorption. Cu, La, and Zr are doped into the lattice of CeO2, whereas Mg is dispersed on the CeO2 surface. The doping of Cu and La into CeO2 leads to an increase of the CO2 adsorption capacity, whereas the doping of Zr has little or no effect. The addition of Mg causes a decrease of the CO2 adsorption capacity at a low Mg content and a gradual increase at a higher content. The CO2 adsorption capacity follows the sequence Cu-CeO2 >La-CeO2 >Zr-CeO2 ≈CeO2 >Mg-CeO2 at low dopant contents, in line with the relative amount of defect sites in the samples. It is the defect sites on the surface, not in the bulk of CeO2, modified by the dopants that play the vital role in CO2 chemisorption. The role of surface oxygen vacancies is further supported by an in situ IR spectroscopic study of the surface chemistry during CO2 adsorption on the doped CeO2.

Efficient charge separation based on type-II g-C3N4/TiO2-B nanowire/tube heterostructure photocatalysts

Separation of photo-generated charges has played a crucial role in controlling the actual performance of a photocatalytic system. Here we have successfully fabricated g-C3N4/TiO2-B nanowire/tube heterostructures through facile urea degradation reactions. Owing to the effective separation of photo-generated charges associated with the type-II band alignment and intimate interfacial contacts between g-C3N4 and TiO2-B nanowires/tubes, such heterostructures demonstrate an improved photocatalytic activity over individual moieties. Synthetic conditions such as hydrothermal temperatures for the preparation of TiO2-B and the weight ratio of TiO2-B to urea were systematically investigated. A high crystallinity of TiO2-B as well as the proper growth of g-C3N4 on its surface are critical factors for a better performance. Our simple synthetic method and the prolonged lifetime of photo-generated charges signify the importance of type-II heterostructures in the photocatalytic applications.

Bismuth and chromium co-doped strontium titanates and their photocatalytic properties under visible light irradiation

Bi/Cr were co-doped into SrTiO₃viatwo synthetic routes. Unlike Cr, Bi does not significantly contribute to the electronic structure near Fermi level.