Novel environmental analytical system based on combined biodegradation and photoelectrocatalytic detection principles for rapid determination of organic pollutants in wastewaters

Environmental ammonia analysis based on exclusive nitrification by nitrifying biofilm screened from natural bioresource

Biofilm-based biological nitrification is widely used for ammonia removal, while hasn't been explored for ammonia analysis. The stumbling block is the coexist of nitrifying and heterotrophic microbes in real environment resulting in non-specific sensing. Herein, an exclusive ammonia sensing nitrifying biofilm was screened from natural bioresource, and a bioreaction-detection system for the on-line analysis of environmental ammonia based on biological nitrification was reported. The nitrifying microbes were aggregated into a nitrifying biofilm through a result-oriented bioresource enrichment strategy. The predominant nitrifying population and progressive surface reaction in the plug flow bioreactor led to the exclusive and exhaustive ammonia biodegradation for the establishment of a novel analytical method. The on-line ammonia monitoring prototype achieved complete biodegradation for determining ammonium nitrogen within 5 min and showed exceptional reliability in long-term real sample measurements without frequent calibration. This work offers a low-threshold natural screening paradigm for developing sustainable bioresource-based analytical technologies.

In situ and self-adaptive BOD bioreaction sensing system based on environmentally domesticated microbial populations

Biochemical oxygen demand (BOD) is a water quality parameter of vital importance. Rapid BOD analysis methods have emerged to simplify the five-day BOD (BOD₅) measurement protocol. However, their universal implementations are restricted by the tricky environmental matrix (including environmental microbes, contaminants, ionic compositions, etc.). Here, an in situ and self-adaptive BOD bioreaction sensing system consisting of a "gut-like" microfluidic coil bioreactor with self-renewed biofilm was proposed for the establishment of a rapid, resilient and reliable BOD determination method. With the spontaneous surface adhesion of environmental microbial populations, the biofilm was colonized in situ on the inner surface of the microfluidic coil bioreactor. Exploiting the environmental domestication during every real sample measurement, the biofilm was capable of self-renewal to adapt to the environmental changes and exhibited representative biodegradation behaviors. The aggregated abundant, adequate and adapted microbial populations in the BOD bioreactor rendered a total organic carbon (TOC) removal rate of 67.7% within a short hydraulic retention time of 99 s. As validated by an online BOD prototype, exceptional analytical performance was achieved in terms of reproducibility (relative standard deviation of 3.7%), survivability (inhibition by pH and metal ion interference of <20%) and accuracy (relative error of -5.9% to 9.7%). This work rediscovered the interactive effects of the environmental matrix on BOD assays and demonstrated an instructive attempt by making use of the environment to develop practical online BOD monitoring devices for water quality assessments.

Acceptor properties of "carbon nanotubes-redox-active polymer based on bovine serum albumin modified with ferrocenecarboxaldehyde" composite for creating a BOD biosensor with Blastobotrys adeninivorans BKM Y-2677 yeast

The possibility of using a composite material based on bovine serum albumin (BSA) covalently bonded with ferrocenecarboxaldehyde and containing carbon nanotubes (CNT) for the immobilization of Blastobotrys adeninivorans BKM Y-2677 (B. adeninivorans) yeast is discussed. The optimal ratio of ferrocenecarboxaldehyde to BSA for the redox-active polymer synthesis is 1:2, since the heterogeneous electron transfer constant is 0.45 ± 0.01 s-1. When carbon nanotubes (CNTs) are added to this polymer, the heterogeneous electron transfer constant increases: at a CNT specific density of 2.5 µg/mm2, it reaches a maximum value of 0.55 ± 0.01 s-1. The addition of CNTs into the conducting system leads to increasing of the rate constant of interaction redox species with B. adeninivorans yeast by an order: the rate constant of interaction between B. adeninivorans yeast and electroactive particles in a redox-active polymer is 0.056 ± 0.005 dm3/g × s and in a composite material based on CNTs is 0.51 ± 0.02 dm3/g × s. The yeast specific density at the electrode of 0.1 mg/mm2 and electrolyte pH of 6.2 was chosen as the working value for the receptor system operation. Immobilized in a composite material, yeast oxidizes a wider range of substrates compared with a similar receptor element based on the ferrocene mediator. The biosensors formed on the basis of hybrid polymers have a high sensitivity with a lower limit of determined concentrations of 1.5 mg/dm3 with an assay time of 5 min and a high correlation (R = 0.9945) with the results of the standard method for determining biochemical oxygen demand (BOD) in nine real surface water samples of the Tula region.

Photo-assisted electrochemical detection of bisphenol A in water samples by renewable {001}-exposed TiO2 single crystals

Bisphenol A (BPA) is a semi-persistent environmental endocrine disrupter and widely present in aqueous environments. Electrochemical detection is an effective method to monitor pollutants like BPA in aqueous environments. However, the electrode fouling from anodic polymeric products is one main barrier of electrochemical sensors for their practical applications. In this work, a renewable electrochemical sensor was rationally designed, constructed and tested for efficient BPA detection. The TiO₂ anodic material was surface-engineered by inorganic-framework molecular imprinting sites with tailored morphological shape, exposed facet and crystal structure. This electrode could be activated mainly as an electrochemical catalyst and partially as a photochemical catalyst. The developed TiO₂-based sensor exhibited a good detection reliability and cyclic stability for determining BPA in water samples, with an electrochemical signal decrease of less than 5.0% in 10-run cyclic tests. By virtue of the bi-functional properties of the tailored TiO₂ anodic material, a unique photo-assisted electrochemical sensor was further developed, in which analyte digestion and analytical signal originated mainly from anodic conversion. Such a synergistic digesting mechanism distinguishes it from the reported electro-assisted photochemical TiO₂ sensors. Our work provides a robust sensor for monitoring pollutants in aqueous environments and a new opportunity to develop renewable electrode materials with good reusability.

Photochemical degradation kinetics and mechanism of short-chain chlorinated paraffins in aqueous solution: A case of 1-chlorodecane

Short chain chlorinated paraffins (SCCPs) have attracted worldwide attention in recent years, due to their high production volume, persistent, bioaccumulative and toxic properties. In this study, 1-chlorodecane (CD) was selected as a model of SCCPs to explore its photochemical degradation behavior under UV irradiation. The results found that CD could be completely photochemical degradation within 120 min, and the ^•OH was found to be the main reactive species from both quenching experiments and electron paramagnetic resonance (EPR) results. However, the contribution of triple excited state of CD (³CD*) was still nonnegligible from the results with the absorption peak at 480 nm obtained by laser flash photolysis. Based on the identified intermediates as well as the data from theoretical chemical calculation, the detailed photochemical degradation mechanism of CD was tentatively proposed that CD firstly was excited and photo-ionized under UV irradiation, and the released Cl^• in water could result in generating ^•OH. Then ^•OH initiates CD degradation mainly through the H-abstraction pathway, leading to the generation of several dehydrogenation radicals, which further generated alcohols or long chain intermediates through radical-radical reactions. The results will provide a comprehensive understanding of the degradation mechanism and environmental fates of SCCPs in water under UV irradiation.

Current status of water environment and their microbial biosensor techniques - Part II: Recent trends in microbial biosensor development

In Part I of the present review series, I presented the current state of the water environment by focusing on Japanese cases and discussed the need to further develop microbial biosensor technologies for the actual water environment. I comprehensively present trends after approximately 2010 in microbial biosensor development for the water environment. In the first section, after briefly summarizing historical studies, recent studies on microbial biosensor principles are introduced. In the second section, recent application studies for the water environment are also introduced. Finally, I conclude the present review series by describing the need to further develop microbial biosensor technologies. Graphical abstract Current water pollution indirectly occurs by anthropogenic eutrophication (Part I). Recent trends in microbial biosensor development for water environment are described in part II of the present review series.

Converting Carbohydrates to Carbon-Based Photocatalysts for Environmental Treatment

Carbohydrates in biomass can be converted to semiconductive hydrothermal carbonation carbon (HTCC), a material that contains plenty of sp²-hybridization structures. Under solar light illumination, HTCC generates photoexcited electrons, holes, and hydroxyl radicals. These species can be used for photocatalytic treatment such as water disinfection and degradation of organic pollutants. The photocatalytic activity of HTCC can be significantly enhanced by iodine doping. The enhancement mechanism is investigated by density functional theoretical calculations and electrochemical measurements. The iodine dopants twist and optimize the structures of the sp²-hybridization in HTCC, thereby favoring photon-induced excitation. Moreover, the iodine dopants facilitate the charge transfer between different sp²-hybridization structures, thus increasing the conductivity and activity of the HTCC. An added benefit is that the I-doped HTCC exhibits lower cytotoxic effect than the pure HTCC. In addition to monosaccharides (glucose), disaccharides (sucrose), and polysaccharides (starch), we have also transformed crops (e.g., rice), plants (e.g., grass), and even agricultural waste (e.g., straw) and animal waste (e.g., cow dung). The conversion of carbohydrates to HTCC may be considered as a "Trash to Treasure" approach. We believe this discovery will attract a lot of attention from researchers involved in environmental catalysis, waste recycling, and pollution treatment.

A Versatile and Scalable Approach toward Robust Superhydrophobic Porous Materials with Excellent Absorbency and Flame Retardancy

The frequent oil spillages and the industrial discharge of organic contaminants have not only created severe environmental and ecological crises, but also cause a risk of fire and explosion. These environmental and safety issues emphasize the urgent need for materials that possess superior sorption capability and less flammability and thus can effectively and safely clean up the floating oils and water-insoluble organic compounds. Here we present the successful hydrophobic modification of the flame retardant melamine sponge with a commercial fluorosilicone, by using a facile one-step solvent-free approach and demonstrate that the resultant superhydrophobic sponge not only exhibits extraordinary absorption efficiency (including high capacity, superior selectivity, good recyclability, and simple recycling routes), but also retains excellent flame retardancy and robust stability. In comparison to conventional methods, which usually utilize massive organic solvents, the present approach does not involve any complicated process or sophisticated equipment nor generates any waste liquids, and thus is a more labor-saving, environment-friendly, energy-efficient and cost-effective strategy for the hydrophobic modification. Taking into account the critical role of hydrophobic porous materials, especially in the field of environmental remediation, the approach presented herein would be highly valuable for environmental remediation and industrial applications.

Toxicity measurement in biological wastewater treatment processes: a review

Biological wastewater treatment processes (WWTPs), by nature of their reliance on biological entities to degrade organics and sometimes remove nutrients, are vulnerable to toxicants present in their influent. Various toxicity measurement methods have been adopted for biological WWTPs, but most are performed off-line, and cannot be adapted to on-line monitoring tools to provide an early warning for WWTP operators. However, the past decade has seen a rapid expansion in the research and development of biosensors that can be used for toxicity assessment of aquatic environments. Some of these biosensors have also been shown to be effective for use in biological WWTPs. Nevertheless, more research is needed to: examine the sensitivity of assays and sensors based on single organisms to various toxicants and develop a matrix of biosensors or a biosensor incorporating multiple organisms that can protect WWTPs; test the micro fuel cell (MFC)-based biosensors with real wastewaters and correlate the results with the well-established oxygen uptake rate (OUR)-based or CH4-based toxicity assay; and, develop advanced data processing methods for interpreting the results of on-line toxicity sensors in real WWTPs to reduce the noise due to the normal fluctuation in influent quality and quantity.

Biochemical oxygen demand measurement by mediator method in flow system

Using mediator as electron acceptor for biochemical oxygen demand (BOD) measurement was developed in the last decade (BODMed). However, until now, no BOD(Med) in a flow system has been reported. This work for the first time describes a flow system of BOD(Med) method (BOD(Med)-FS) by using potassium ferricyanide as mediator and carbon fiber felt as substrate material for microbial immobilization. The system can determine the BOD value within 30 min and possesses a wider analytical linear range for measuring glucose-glutamic acid (GGA) standard solution from 2 up to 200 mg L(-1) without the need of dilution. The analytical performance of the BOD(Med)-FS is comparable or better than that of the previously reported BOD(Med) method, especially its superior long-term stability up to 2 months under continuous operation. Moreover, the BOD(Med)-FS has same determination accuracy with the conventional BOD5 method by measuring real samples from a local wastewater treatment plant (WWTP).

Microbial fuel cell-based biosensors for environmental monitoring: a review

The microbial fuel cell (MFC) is an innovative technology that was initially designed to harness energy from organic waste using microorganisms. It is striking how many promising applications beyond energy production have been explored in recent decades. In particular, MFC-based biosensors are considered to be the next generation biosensing technology for environmental monitoring. This review describes recent advances in this emerging technology of MFC-based biosensors, with a special emphasis on monitoring of biochemical oxygen demand and toxicity in the environment. The progress confirms that MFC-based biosensors could be used as self-powered portable biosensing devices with great potential in long-term and remote environmental monitoring.

Collagen nanofibers facilitated presynaptic maturation in differentiated neurons from spinal-cord-derived neural stem cells through MAPK/ERK1/2-Synapsin I signaling pathway

Neural stem cells (NSCs) are deemed to be a potential cell therapy for brain and spinal cord reconstruction and regeneration following injury. In this study, we investigated the role of nanofibrous scaffolds on NSCs-derived neurons in the formation of neural networks. Miniature excitatory postsynaptic currents (mEPSCs) were recorded using the whole-cell patch clamp recording method after the spinal cord-derived NSCs were differentiated into neurons and cultured in vitro for 10-14 days. It was observed that the frequency of mEPSCs in the differentiated neurons cultured on both randomly oriented and aligned collagen nanofibrous scaffolds was higher than that on the collagen-coated control and can be inhibited by an ERK inhibitor (PD98059), indicating that the collagen nanofibers affected the maturation of the synapses from presynaptic sites via the MAPK/ERK1/2 pathway. In addition, both of the collagen nanofibers increased the phosphorylation of Synapsin I and facilitated the interaction of p-ERK1/2 and p-Synapsin I. All these results suggested that the collagen nanofibrous scaffolds contributed to the presynaptic maturation via the ERK1/2-Synapsin I signaling pathway.