Synthesis of Core-Shell Magnetic Fe3O4@poly(m-Phenylenediamine) Particles for Chromium Reduction and Adsorption

Steam activation of porous concave polymer nanospheres for high-efficient chromium and cadmium removal

The issue of heavy metal contamination in water is a global concern, and the development of highly efficient adsorbent materials is crucial for the removal and detoxification of heavy metals. Polymer-based materials have emerged as a promising class of adsorbents due to their ability to capture heavy metal pollutants and reduce them to less toxic forms. The limited surface area of conventional polymer adsorbents makes them less effective for high-capacity adsorption. Herein, we present a low-temperature steam activation approach to address this challenge. This activation approach leads to a remarkable increase of over 20 times in the surface area of concave aminophenol-formaldehyde (APF) polymer nanospheres (from 45 to 961 m2/g) while preserving their reductive functional groups. The activated concave APF nanospheres were evaluated for their adsorption capabilities towards two typical heavy metal ions (i.e., Cr(VI) and Cd(II)) in aqueous solutions. The maximum adsorption capacities achieved were 1054 mg g-1 for Cr(VI) and 342 mg g-1 for Cd(II), which are among the highest performances reported in the literature and are much higher than the capacities of the non-activated APF nanospheres. Additionally, approximately 71.5 % of Cr(VI) was simultaneously reduced to Cr(III) through the benzenoid amine pathway during adsorption, highlighting the crucial role of the steam activation strategy in enhancing the capability of polymer adsorbents.

Highly efficient Cu(II) capture by salicylaldoxime functionalized magnetic polydopamine core-shell hybrids: Behavior and mechanism

Functionalized magnetic nanocomposites were considered as promising adsorbents owing to their abundant functional groups and ease of separation properties. Herein, we combined the solvothermal method with molecular copolymerization to synthesize a salicylaldoxime-grafted magnetic polydopamine (SMP) core-shell hybrid and exploited it for Cu(II) adsorption. The physicochemical properties of SMP were comprehensively studied by SEM, TEM, XRD, FT-IR, TGA, XPS, and VSM measurements. The results manifested that polydopamine acts as a bridge connecting magnetic iron oxide and salicylaldoxime to fabricated core-shell hybrids with rich functional groups. The batch experimental results showed that the Cu(II) adsorption was consumingly pH-reliant behavior, while adsorption data fitted the pseudo-second-order kinetic model and Langmuir isothermal model well, and the adsorption process achieved equilibrium within 60 min. Moreover, SMP exhibited remarkable anti-interference and can be recycled for 5 times with an inconspicuous decrease in adsorption performance. Importantly, salicylaldoxime functionalization endowed SMP with maximum Cu(II) adsorption capacity of 141.24 mg/g at pH 6.0 and 25 °C as compared with pure MP. Based on FT-IR and XPS study, the main adsorption mechanisms were proposed with a synergistic effect including a strong chemical chelation and partial Cu(II) reduction. Importantly, this strategy can be extended to multifunctional magnetic composites for Cu-contaminated wastewater cleanup.

New insights into long-lasting Cr(VI) removal from groundwater using in situ biosulfidated zero-valent iron with sulfate-reducing bacteria

Sulfidation enhances the reactivity of zero-valent iron (ZVI) for Cr(VI) removal from groundwater. Current sulfidation methods mainly focus on chemical and mechanical sulfidation, and there has been little research on biosulfidation using sulfate-reducing bacteria (SRB) and its performance in Cr(VI) removal. Herein, the ability of the SRB-biosulfidated ZVI (SRB-ZVI) system was evaluated and compared with that of the Na2S-sulfidated ZVI system. The SRB-ZVI system forms a thicker and more porous FeSx layer than the Na2S-sulfidated ZVI system, resulting in more sufficient sulfidation of ZVI and a 2.5-times higher Cr(VI) removal rate than that of the Na2S-sulfidated ZVI system. The biosulfidated-ZVI granules and FeSx suspension are the major components of the SRB-ZVI system. The SRB-ZVI system exhibits a long-lasting (11 cycles) Cr(VI) removal performance owing to the regeneration of FeSx. However, the Na2S-sulfidated ZVI system can perform only two Cr(VI) removal cycles. SRB attached to biosulfidated-ZVI can survive in the presence of Cr(VI) because of the protection of the biogenic porous structure, whereas SRB in the suspension is inhibited. After Cr(VI) removal, SRB repopulates in the suspension from biosulfidated-ZVI and produce FeSx, thus providing conditions for subsequent Cr(VI) removal cycles. Overall, the synergistic effect of SRB and ZVI provides a more powerful and environmentally friendly sulfidation method, which has more advantageous for Cr(VI) removal than those of chemical sulfidation. This study provides a visionary in situ remediation strategy for groundwater contamination using ZVI-based technologies.

Efficient removal of tetracycline in water using modified eggplant straw biochar supported green nanoscale zerovalent iron: synthesis, removal performance, and mechanism

A novel NaOH modified eggplant straw biochar supported green nanoscale zerovalent iron (P-nZVI/ESBC) composite was synthesized and its removal performance and reaction mechanism for tetracycline (TC) in water were investigated. Multiple characterizations showed that the prepared P-nZVI/ESBC composite contained oxygen-containing functional groups (hydroxyl, carbonyl, and carboxyl groups) and Fe species (nZVI and its oxides). The dosage of composite, temperature, and solution pH significantly affected the removal capacity of the P-nZVI/ESBC composite for TC. The Avrami fraction-order kinetic model and Sips adsorption isotherm model can fit well the removal process of TC by the P-nZVI/ESBC composite, indicating that the adsorption behavior of TC involved multiple adsorption mechanisms and chemical adsorption might occur. The maximum adsorption capacity of the P-nZVI/ESBC composite for TC was 304.62 mg g-1. The adsorption and reductive degradation were the dominant mechanisms of TC removal by the P-nZVI/ESBC composite. This work offers abundant information on the application of eggplant straw to manufacture biochar-based composites for the efficient removal of antibiotic contaminants from aquatic environments.

Sulfhydryl-Functionalized Amino Group Polymer Microcomposites toward Efficient Adsorption of Aqueous Cr(VI), As(III), Cd(II), and Pb(II)

The development of efficient adsorbents for heavy metal pollution, especially five toxic heavy metals, has attracted great research interest. Polymer-based adsorbents have aroused research value for their abundant functional groups and high porosity to the ability to capture metal ions. We designed a sulfhydryl-functionalized polymer microcomposite to take up Cr(VI), As(III), Cd(II), and Pb(II). The adsorption capacity achieved was 64.2 mg g-1 for Cr(VI), 44.9 mg g-1 for As(III), 35.5 mg g-1 for Cd(II), and 18.2 mg g-1 for Pb(II). Langmuir and Sips isotherm model is dominant for As(III), Cd(II), and Pb(II) adsorption. Pseudo-second-order kinetic models can better describe the adsorption behavior of Cr(VI), implying that chemisorption is accompanied by Cr(VI) adsorption. Cr(VI) simultaneous reduction to Cr(III) through the benzenoid amine oxidate pathway was the dominant mechanism, precipitation for Cd(II) adsorption was convinced, and chelation between As(III)/Pb(II) and─SH group and complexation between Pb(II) and C═O or benzene hydroxyl were a plausible mechanism for As(III) and Pb(II) adsorption.

Poly(2-vinylpyridine)/MCM-41 Composites with Micropores and Switchable Mesopores for the Removal of Cr(VI)

Porous structure design and reversible regulation of pore size during adsorption-desorption are crucial to the removal of pollutants in water such as Cr(VI). In this paper, micropores and switchable mesopores were constructed on MCM-41 to further improve adsorption-desorption performance of Cr(VI) via the confinement effect of micropores and opening and closing of mesopores. 2-Vinylpyridine was introduced and polymerized into the pores and on the pore mouth of MCM41 modified by C═C group (AM41) under the irradiation of ultraviolet light. The obtained samples (PM41) possessed mesopores (2.73 nm) and micropores (1.36 nm), where mesopores could open or close under different pH and micropores showed the confinement effect because their pore size is close to Cr(VI) diameter (0.87 nm). Compared with MCM-41, the introduction of poly(2-vinylpyridine) enhanced obviously its adsorptive ability and it trapped most of the Cr(VI) (99%) in solution, 12 times higher than that of the parent sample. The change of pore size is favorable to the cycle performance, and after 3 times recycling, the removal rate of Cr(VI) by PM41-20 remained above 88%. Langmuir isotherm showed a better data correlation than the Freundlich model. Cr(VI) in solution was removed by electrostatic interaction between the pyridine group and Cr(VI) and the confinement effect from micropores.

Insights into the proton-enhanced mechanism of hexavalent chromium removal by amine polymers in strong acid wastewater: Reduction of hexavalent chromium and sequestration of trivalent chromium

Adsorption is a green technology of treating heavy metal-contaminated strong acid wastewaters for the recycling of heavy metal and reuse of strong acid. Herein, three amine polymers (APs) with different alkalinities and electron donating abilities were prepared to investigate the adsorption-reduction processes of Cr(VI). It was found that the removal of Cr(VI) was controlled by the concentration of -NRH+ on the surface of APs at pH > 2, which relies on the alkalinity of APs. However, the high concentration of NRH+ significantly facilitated the adsorption of Cr(VI) on the surface of APs and accelerated the mass transfer between Cr(VI) and APs at strong acid environment (pH ≤ 2). More importantly, the reduction of Cr(VI) was enhanced at pH ≤ 2, due to the high reduction potential of Cr(VI) (E ≥ 0.437). The ratio of reduction to adsorption (α) of Cr(VI) was above 0.70, and the proportion of Cr(III) bonding on Ph-AP excessed 67.6 %. Finally, a proton-enhanced mechanism of Cr(VI) removal was verified by analyzing FTIR and XPS spectra as well as constructing DFT model. This study provides a theoretical basis for the removal of Cr(VI) in the strong acid wastewater.

Highly efficient Cr (VI) removal from electroplating wastewater by regenerable copper sulfides: Mechanism and magical induction effect for Cr resource recovery

The current sorbents used to remove Cr (VI) from electroplating wastewater are faced with some challenges including the difficulty in separating, regenerating, and safely disposing of adsorbed Cr species. To address these challenges, CuSx/TiO2 was developed to recover Cr (VI) from electroplating wastewater. CuSx/TiO2 had superior performance in removing Cr (VI), with the rate and capacity of approximately 9.36 mg g-1 h-1 and 68.8 mg g-1 at initial pH 4.0, respectively. Additionally, Cu2+ released from CuSx/TiO2 during Cr (VI) removal would come back to its external surface as the Cu(OH)2 precipitate at initial pH 4.0, which helped to prevent the generation of secondary pollution. The Cu(OH)2 precipitate would be decomposed into CuOx after calcination, which would then be transformed back into CuSx by re-sulfuration for regeneration. Hence, CuSx showed a magical induction effect on Cr (VI) recovery, and Cr (VI) from electroplating wastewater might be gradually enriched as Cr2O3 in the sandwich between CuSx and TiO2 through multiple regenerations and removals, which could be considered as a chromium ore resource for industrial applications when the amount of enriched Cr2O3 reached more than 30 wt%. Overall, CuSx/TiO2 showed great potential as a promising sorbent for Cr (VI) removal from electroplating wastewater.

Sorption enhancement of Cr(VI) from aqueous solution by polyaniline confined in three-dimensional network of composite porous hydrogel

Hexavalent chromium Cr(VI) is a typical harmful pollutant, which is carcinogenic or mutagenic to aquatic animals and humans. In this study, sepiolite/humic acid/polyvinyl alcohol@ polyaniline (SC/HA/PVA@PANI) composite porous hydrogel adsorbent was synthesized by Pickering emulsion template in situ chemical oxidative polymerization for adsorption of Cr(VI) from aqueous solution. The in situ polymerization of aniline at the Pickering emulsion interface and the unique three-dimensional network structure of the hydrogel act as an effective "confinement" for the growth of the polymer. The porous structure of the material acts as a water channel, which effectively accelerates the binding of the adsorbate to the adsorption sites, and significantly improves the adsorption rate and adsorption capacity. The adsorption capacity of PANI for Cr(VI) confined in three-dimensional network of composite porous SC/HA/PVA@PANI hydrogel reached 1180.97 mg/g-PANI, which increased about 27-fold compared the adsorption capacity of pure PANI (43.48 mg/g). It is shown that the experimental design effectively avoids the agglomeration of PANI and improves its potential adsorption performance. In addition, the analysis of FESEM-EDX, FT-IR, and XPS spectra before and after adsorption confirmed that the main adsorption mechanisms of Cr(VI) on SC/HA/PVA@PANI included ion exchange, electrostatic attraction, and redox reaction. In conclusion, SC/HA/PVA@PANI has good stability and excellent adsorption performance, which is a new type of Cr(VI) ion adsorbent with great potential.

Removal of Fe(III)/Al(III)/Mg(II) by phosphonic group functionalized resin in wet-process phosphoric acid: Mechanism and intrinsic selectivity

The removal of iron ions (Fe(III)), aluminum ions (Al(III)), and magnesium ions (Mg(II)) in phosphoric acid (H₃PO₄) solution is vital for the production of H₃PO₄ and supply of phosphate fertilizer. However, the mechanism and intrinsic selectivity for removal of Fe(III), Al(III), and Mg(II) from wet-process phosphoric acid (WPA) by phosphonic group (-PO₃H₂) functionalized MTS9500 are still unclear. In this work, the removal mechanisms were determined via combined analysis of FT-IR, XPS, molecular dynamics (MD), and quantum chemistry (QC) simulations based on density functional theory (DFT). The metal-removal kinetics and isotherms were further studied to confirm the removal mechanisms. The results indicate that Fe(III), Al(III), and Mg(II) interact with the -PO₃H₂ functional groups in MTS9500 resin with sorption energies of -126.22 kJ·mol^-1, -42.82 kJ·mol^-1, and -12.94 kJ·mol^-1, respectively. Moreover, the intrinsic selectivities of the resin for Fe(III), Al(III), and Mg(II) removal were quantified by the selectivity coefficient (S_i/j). The S_{Fe(III)/Al(III)}, S_{Fe(III)/Mg(II)} and S_{Al(III)/Mg(II)} are 18.2, 55.1 and 3.02, respectively. This work replenishes sorption theory that can be used in the recycling of electronic waste treatment acid, sewage treatments, hydrometallurgy, and purification of WPA in industry.

Photocatalytic degradation of norfloxacin by magnetic molecularly imprinted polymers: influencing factors and mechanisms

Novel magnetic molecularly imprinted polymers (MMIP) were prepared for selective removal of norfloxacin by effectively utilizing photocatalytic degradation and magnetic separation techniques. The imprinted material with titanium layer and multihole surface showed an excellent photocatalytic property. In this paper, the kinetics of photocatalytic degradation of norfloxacin by MMIP was explored, and the influences of environmental factors, including solution pH, humic acid, common ions and water media on photocatalytic performance of MMIP were elucidated. The results showed that MMIP had good adaptability and could degrade norfloxacin within 60 min, but the degradation rate constant decreased in surface water. Based on the identification of intermediate products, the possible degradation pathways of norfloxacin were analysed, speculating that it might be degraded into small molecules in the form of de-piperazine ring, de-carboxyl group and de-fluorine. Moreover, the mineralization ratio of norfloxacin could reach 84.2% after ultraviolet irradiation for 150 min, and the low cobalt release of MMIP enhanced the security of the material. The results of adsorption and degradation cycle tests showed that MMIP obtained by molecular imprinting technology had excellent performance in sustainable use for micro organic pollutants removal.

Preparation of sludge-cyanobacteria composite carbon for synergistically enhanced co-removal of Cu(II) and Cr(VI)

Traditional sludge disposal is currently restricted by the risk of secondary pollution. Sludge carbon material has gained widespread attention because of its low cost and environmentally sustainable properties. However, owing to the high ash content and low-energy density of sludge, sludge pyrolysis alone has certain limitations, and the performance of carbon materials needs to be improved. Herein, a sludge-cyanobacteria composite carbon (SCC) was easily synthesized, and the adsorption process of Cu(II) and Cr(VI) by SCC was examined. SCC-700-2-50% exhibited a high S_BET (1047.54 m²/g) and developed pore structure rich in functional groups (such as -NH, -OH, and C-O). The combination of pore structure and functional groups improved the adsorption performance of SCC. The adsorption processes exhibited a synergistic effect in a binary system: the q_m of Cu(II) and Cr(VI) were 386 mg/g and 341 mg/g, respectively, and the selectivity of Cu(II) adsorption by SCC was greater than Cr(VI). The adsorption process, examined by SEM-EDS, FTIR, and XPS analysis, indicated that Cu(II) as a cationic interface strengthens Cr(VI) adsorption through electrostatic interaction, and the anion Cr(VI) created a valid electrostatic shield against the electrostatic repulsion between H⁺ and Cu(II), facilitating Cu(II) adsorption. SCC had great reusability: Cu(II) and Cr(VI) adsorption capacity were 90% and 84%, of the initial adsorption capacity, respectively, after six cycles. This study demonstrates the prospect of SCC as a valid adsorbent for multiple heavy metal contaminations removal.

Mussel-inspired magnetic adsorbent MnO2/PDA@Fe3O4 for removing heavy metal ions contaminants in single and mixed systems

Heavy metal pollution has been a magnificent concern for a long period. A novel magnetic material, MnO₂/PDA@Fe₃O₄, was prepared in this paper. With the assistance of multiple characterization methods, it was confirmed that polydopamine coated the magnetic nucleus and acted as a dense intermediate layer for MnO₂ attachment. Having superior adsorption performance, MnO₂/PDA@Fe₃O₄ could remove heavy metal cations efficiently no matter in single or mixed systems. The maximum adsorption capacities calculated by the Langmuir model for Pb(II), Cu(II), and Cd(II) were 295.01 mg/g, 130.30 mg/g, and 115.16 mg/g, respectively. In mixed systems, the adsorbent showed obvious selectivity for Pb(II). And the variation of Cu(II) concentration was more responsible for Pb(II) adsorption than that of Cd(II). The kinetic and thermodynamic data revealed that the polluted ions immobilizations by MnO₂/PDA@Fe₃O₄ were chemisorption and were endothermic, entropy increase, spontaneous process. The presence of humic acid and coexisting ions induced only a very limited interference. In addition, MnO₂/PDA@Fe₃O₄ maintained excellent adsorption performance and stability after five cycles of adsorption and removed 98.33% Pb(II) and 71.24% Cu(II) from actual water, respectively. This study confirmed that the MnO₂/PDA@Fe₃O₄ had great potential and broad prospects to remediate the heavy metal contaminants in water.

Removal of As(III)/As(V) from aqueous solution using newly developed thiosalicylic acid coated magnetite [TSA@Fe3O4] nanoparticles

The aim of this study was to develop an affordable adsorption methodology for removal of As(III)/As(V) from contaminated water. Herein, novel adsorbent TSA@Fe₃O₄ nanoparticles (NPs) were synthesized by decorating thiosalicylic acid (TSA) on magnetite nanoparticles (Fe₃O₄ NPs) and employed for removal of As(III)/As(V) species from artificially contaminated natural water systems. TSA@Fe₃O₄ NPs demonstrated excellent adsorption efficiency (AE) and 98% of As(V) and 93% of As(III) was removed at optimized experimental conditions. The adsorption kinetic and equilibrium isotherm studies were conducted preferentially for As(III) adsorption. Adsorption followed the pseudo-second-order kinetic (R² = 99%) and adsorption data fitted well in Langmuir isotherm model (R² = 99%) and maximum adsorption capacity (Q_max = 34.1 mg/g) was calculated for 5 mg/L of As(III) by using 10 mg of TSA@Fe₃O₄ NPs. The effect of pH, contact time, adsorption dosages, and competitive anions was also examined to identify optimum experimental conditions. The adsorbent was characterized by advanced instrumental techniques to investigate the physicochemical properties and stability of NPs. To comprehend the interactions of As(III) species with adsorbent NPs, NPs were analyzed using XPS and Raman spectroscopy techniques. Both the techniques confirmed that As(III) and As(V) species present simultaneously on adsorbent surface. The TSA@Fe₃O₄ was regenerated using 0.1 M NaOH. The findings of this study suggested that TSA@Fe₃O₄ NPs could be considered a potential adsorbent for effective remediation of As(III) and As(V) from contaminated natural water systems.

Design of cryogel based CNTs-anchored polyacrylonitrile honeycomb film with ultra-high S-NZVI incorporation for enhanced synergistic reduction of Cr(VI)

An ultra-high NZVI-loaded PAN film (S-CPN) with a unique 3D honeycomb structure was designed based on the cryogel method of green solvent-induced pores and confinement of the spatially free conformation of films by anchoring carbon nanotubes (CNTs), supplemented sulfidation for removing hexavalent chromium (Cr(VI)), and characterized by SEM, AFM, BET, XRD, XPS, and electrochemical corrosion. The doping amounts of the compounds for S-CPN synthesis were optimized to be 0.075 g CNTs, 0.25 g Na₂S, and 0.3 M FeSO₄. S-CPN possessed a 175.247 m²/g specific surface area, -0.365 V reduction potential, and 46.54 mg/g ultra-high NZVI-loading. S-CPN had the strong activity of Cr(VI) removal and tolerance to coexisting ions. The removal efficiency remained at 80 % after age for 30 days or 5 cycles. The pseudo-first-order kinetics and Langmuir model were more favorable to simulate the adsorption of Cr(VI) on S-CPN. The thermodynamics show that S-CPN removing Cr(VI) was a spontaneous exothermic reaction. The reasons for these excellent properties were that CNTs improve the film porosity and ultra-high NZVI-loading, and synergistic the FeS_X layer to chelates-reduces Cr(VI). This was the first time that honeycomb film with 3D structure and potential applications in heavy metal removal was developed via an eco-friendly strategy.

Systematic and Bibliometric Analysis of Magnetite Nanoparticles and Their Applications in (Biomedical) Research

Recent reports show air pollutant magnetite nanoparticles (MNPs) in the brains of people with Alzheimer's disease (AD). Considering various field applications of MNPs because of developments in nanotechnology, the aim of this study is to identify major trends and data gaps in research on magnetite to allow for relevant environmental and health risk assessment. Herein, a bibliometric and systematic analysis of the published magnetite literature (n = 31 567) between 1990 to 2020 is completed. Following appraisal, publications (n = 244) are grouped into four time periods with the main research theme identified for each as 1990-1997 "oxides," 1998-2005 "ferric oxide," 2006-2013 "pathology," and 2014-2020 "animal model." Magnetite formation and catalytic activity dominate the first two time periods, with the last two focusing on the exploitation of nanoparticle engineering. Japan and China have the highest number of citations for articles published. Longitudinal analysis indicates that magnetite research for the past 30 years shifted from environmental and industrial applications, to biomedical and its potential toxic effects. Therefore, whilst this study presents the research profile of different countries, the development in research on MNPs, it also reveals that further studies on the effects of MNPs on human health is much needed.

Polyacrylonitrile/Aminated Polymeric Nanosphere Nanofibers as Efficient Adsorbents for Cr(VI) Removal

In this work, polyacrylonitrile/aminated polymeric nanosphere (PAN/APN) nanofibers were prepared by electrospinning of monodispersed aminated polymeric nanospheres (APNs) for removal of Cr(VI) from aqueous solution. Characterization results showed that obtained PAN/APNs possessed nitrogen functionalization. Furthermore, the adsorption application results indicated that PAN/APN nanofibers exhibited a high adsorption capacity of 556 mg/g at 298 K for Cr(VI) removal. The kinetic data showed that the adsorption process fits the pseudo-second order. A thermodynamic study revealed that the adsorption of Cr(VI) was spontaneous and endothermic. The coexisting ions Na⁺, Ca²⁺, K⁺, Cl⁻, NO₃⁻ and PO₄³⁻ had little influence on Cr(VI) adsorption, while SO₄²⁻ in solution dramatically decreased the removal performance. In the investigation of the removal mechanism, relative results indicated that the adsorption behavior possibly involved electrostatic adsorption, redox reaction and chelation. PAN/APN nanofibers can detoxify Cr(VI) to Cr(III) and subsequently chelate Cr(III) on its surface. The unique structure and nitrogen functionalization of PAN/APN nanofibers make them novel and prospective candidates in heavy metal removal.

Simultaneous and efficient removal of multiple heavy metal(loid)s from aqueous solutions using Fe/Mn (hydr)oxide and phosphate mineral composites synthesized by regulating the proportion of Fe(II), Fe(III), Mn(II) and PO43

In this work, a novel adsorbent FMPs consisting of Fe/Mn (hydr)oxides and phosphate minerals was synthesized by regulating the proportion of Fe(II), Fe(III), Mn(II) and PO₄^3-, and its removal behaviors and possible mechanisms for Cd(II), Pb(II), Cu(II), Zn(II), As(III), Sb(III), As(V) and Sb(V) were systematically investigated. Batch adsorption experiments revealed that the adsorption process of FMPs to these metal(loid) ions conformed to pseudo-second-order (R² > 0.99) and Redlich-Peterson (R² > 0.94) models in the mono-component system, demonstrating a hybrid chemical reaction-adsorption process. In addition, the solution pH and ionic strength could affect the adsorption capacity of FMPs to heavy metal(loid)s with varying degrees. Besides, FMPs presented feasible stability and reusability even after four cycles. Combining the macroscopic and microscopic characteristics, the adsorption mechanisms of FMPs mainly included surface complexation, electrostatic adsorption, inner-sphere complexation, hydrogen bonding, redox and pore-filling. In a multi-component system, FMPs exhibited an excellent affinity for capturing Pb(II) and Sb(III/V). This work provides an alternative method for designing and developing a series of novel adsorbent in removing multiple heavy metal(loid)s from wastewater, and demonstrated its application prospect in the remediation of multi-metal(loid) composite polluted water.

Kinetics and Mechanisms of Cr(VI) Removal by nZVI: Influencing Parameters and Modification

In this study, single-spherical nanoscale zero valent iron (nZVI) particles with large specific sur-face area were successfully synthesized by a simple and rapid chemical reduction method. The XRD spectra and SEM–EDS images showed that the synthesized nZVI had excellent crystal struc-ture, but oxidation products, such as γ-Fe2O3 and Fe3O4, were formed on the surface of the parti-cles. The effect of different factors on the removal of Cr(VI) by nZVI were studied, and the opti-mum experimental conditions were found. Kinetic and thermodynamic equations at different temperatures showed that the removal of Cr(VI) by nZVI was a single-layer chemical adsorption, conforming to pseudo-second-order kinetics. By applying the intraparticle diffusion model, the ad-sorption process was composed of three stages, namely rapid diffusion, chemical reduction, and in-ternal saturation. Mechanism analysis demonstrated that the removal of Cr(VI) by nZVI in-volved adsorption, reduction, precipitation and coprecipitation. Meanwhile, Cr(VI) was reduced to Cr(III) by nZVI, while FeCr2O4, CrxFe1−xOOH, and CrxFe1−x(OH)3 were formed as end products. In addition, the study found that ascorbic acid, starch, and Cu modified nZVI can promote the removal efficiency of Cr(VI) in varying degrees due to the enhanced mobility of the particles. These results can provide new insights into the removal mechanisms of Cr(VI) by nZVI.

Cellulose-based aerogel beads for efficient adsorption-reduction-sequestration of Cr(VI)

The reduction and sequestration of toxic Cr(VI) via a one-step process in an aqueous solution is critical to eliminate its environmental risk. In this study, amine functionalized cellulose-based aerogel beads (CGP) was developed for simultaneous and efficient adsorption- reduction- sequestration of Cr(VI). CGP showed a maximum Cr(VI) adsorption capacity of 386.40 mg/g at 25 °C due to its strong electrostatic attraction towards Cr(VI). The simultaneous Cr(VI) adsorption- reduction- sequestration performance of CGP over a wide Cr(VI) concentration range was examined. The mechanism was investigated in-depth via the analysis of adsorption kinetics, XPS spectra, and FTIR spectra. Moreover, the Cr immobilization stability of CGP after adsorption was evaluated in simulated neutral, acidic, and alkaline conditions. The effect of pH, temperature, ionic strength and the presence of interfering ions on CGP adsorption performance were investigated by batch adsorption experiments. Fixed-bed column adsorption study was performed to explore the application potential of CGP beads in a wastewater treatment process.

Upcycling of blending waste plastics as zwitterionic hydrogel for simultaneous removal of cationic and anionic heavy metals from aqueous system

Upcycling of waste plastics as functional materials is a new approach for synthesizing low-cost and durable adsorbents with zwitterionic property. Herein, a facile process for recycling blending waste plastics to fabricate zwitterionic plastic-g-hydrogel (ZPH) for simultaneous adsorbing cationic and anionic heavy metals was developed. ZPH possessed high affinities for cations and anions in both acid and alkaline conditions owing to its zwitterionic property, and the maximum adsorption capacities of Pb²⁺, Cd²⁺, Ba²⁺, and Cr(VI) (Cr₂O₇^2-) were 132.13, 85.58, 69.92 and 85.15 mg/g, respectively. Mechanism study indicated the incompatibility of blending plastics was skillfully overcome through the crosslinking between sodium alginate (SA)/chitosan (CTS) and plastics. Cations were adsorbed onto ZPH via electrostatic interaction, cation exchange and coordination interactions with Cl/N/O-containing groups. Furthermore, the reduction of Cr(VI) to Cr(III) was another important path for ZPH to capture anionic Cr₂O₇^2-, and subsequently Cr(III) was adsorbed via coordination interaction and cation exchange. Moreover, the regeneration experiment showed ZPH possessed excellent reusability and stable structure. Accordingly, this research provides a profitable approach for recycling blending plastics, and ZPH has potentials for industrial application in wastewater treatment or contaminated site remediation with complex heavy metals pollution.

Enhancing the remarkable adsorption of Pb2+ in a series of sulfonic-functionalized Zr-based MOFs: a combined theoretical and experimental study for elucidating the adsorption mechanism

A series of Zr-based metal-organic frameworks was prepared via the solvothermal route using sulfonic-rich linkers for the efficient capture of Pb²⁺ ions from aqueous medium. The factors affecting adsorption such as the solution pH, adsorbent dosage, contact time, adsorption isotherms, and mechanism were studied. Consequently, the maximum adsorption capacity of Pb²⁺ on the acidified VNU-23 was determined to be 617.3 mg g^-1, which is much higher than that of previously reported adsorbents and MOF materials. Furthermore, the adsorption isotherms and kinetics of the Pb²⁺ ion are in good accordance with the Langmuir and pseudo-second-order kinetic model, suggesting that the uptake of Pb²⁺ is a chemisorption process. The reusability experiments demonstrated the facile recovery of the H⁺⊂VNU-23 material through immersion in an HNO₃ solution (pH = 3), where its Pb²⁺ adsorption efficiency still remained at about 90% of the initial uptake over seven cycles. Remarkably, the adsorption mechanism was elucidated through a combined theoretical and experimental investigation. Accordingly, the Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, scanning electron microscopy connected to energy-dispersive X-ray mapping (SEM-EDX-mapping), and X-ray photoelectron spectroscopy (XPS) analysis of the Pb⊂VNU-23 sample and comparison with H⁺⊂VNU-23 confirmed that the electrostatic interaction occurs via the interaction between the SO₃^- moieties in the framework and the Pb²⁺ ion, leading to the formation of a Pb-O bond. In addition, the density functional theory (DFT) calculations showed the effective affinity of the MOF adsorbent toward the Pb²⁺ ion via the strong driving force mentioned in the experimental studies. Thus, these findings illustrate that H⁺⊂VNU-23 can be employed as a potential adsorbent to eliminate Pb²⁺ ions from wastewater.

Surface protection method for the magnetic core using covalent organic framework shells and its application in As(III) depth removal from acid wastewater

Fe₃O₄-based materials are widely used for magnetic separation from wastewater. However, they often suffer from Fe-leaching behavior under acidic conditions, decreasing their activity and limiting sustainable practical applications. In this study, covalent organic frameworks (COFs) were used as the shell to protect the Fe₃O₄ core, and the Fe₃O₄@COF core-shell composites were synthesized for As(III) removal from acid wastewater. The imine-linked COFs can in situ grow on the surface of the Fe₃O₄ core layer by layer with [COFs/Fe₃O₄]_mol ratio of up to 2:1. The Fe-leaching behavior was weakened over a wide pH range of 1-13. Moreover, such composites keep their magnetic characteristic, making them favorable for nanomaterial separation. As(III) batch adsorption experiments results indicated that, when COFs are used as the shell for the Fe₃O₄ core, a balance between As(III) removal efficiencies and the thickness of the COF shell exists. Higher As(III) removal efficiencies are obtained when the [COFs/Fe₃O₄]_mol ratios were < 1.5:1, but thicker COF shells were not beneficial for As(III) removal. Such composites also exhibited better As(III) removal performances in the pH range of 1-7. Over a wide pH range, the zeta potential of Fe₃O₄@COF core-shell composites becomes more positive, which benefits the capture of negative arsenic ions. In addition, thinner surface COFs were favorable for mass transfer and facilitating the reaction of Fe and As elements. Our study highlights the promise of using COFs in nanomaterial surface protection and achieving As(III) depth removal under acidic conditions.

Highly efficient and selective capture Pb(II) through a novel metal-organic framework containing bifunctional groups

The design and development of materials with a selective adsorption capacity for Pb(II) are very important for environmental governance and ecological safety. In this work, a novel 3D metal-organic framework ([Cd₂H₄L₄Cl₂SO₄]·4H₂O, Cd-MOF) is constructed using a multiple pyrazole heterocycles tetraphenylethylene-based ligand (H₄L₄) and CdSO₄ which containing Pb(II) adsorption sites (SO₄^2-). Studies have shown that the Cd-MOF has outstanding stability, and its maximum adsorption value of Pb(II) can be as high as 845.55 mg/g, which is higher than that of most MOFs or MOFs modified materials. It is worth emphasizing that the Cd-MOF have excellent recyclability due to the unique adsorption mechanism of the Cd-MOF. Thermodynamic studies have shown that Pb(II) adsorption of the Cd-MOF is a spontaneous endothermic process. Specific selective adsorption, exceptional stability and remarkable recyclability make the Cd-MOF a potential material for industrial capture and recovery of Pb(II) from water.

Synchronous Efficient Reduction of Cr (VI) and Removal of Total Chromium by Corn Extract / Fe (III) System

In this study, a cost-effective and environmentally friendly composite system for the remediation of Cr (VI)-polluted groundwater was developed. The system of simultaneous reduction of Cr (VI) and precipitation of Cr (III) was innovatively constructed, using corncob extract as electron donor and Fe (III) as strengthening reagent. In the process of the total chromium removal, the addition of alkaline substances was not required, when pH ≤ 4 it showed an optimal reduction of Cr (VI). In addition, the removal rate of total chromium reached 88% within 120 min. To understand the mechanism of this system, we characterized the corn extract and particulate matter before and after the reaction. Fourier transform infrared spectroscopy and gas chromatography-mass spectrometry suggested that alcohols, phenols, and aldehydes provided the electrons that were required to reduce Cr (VI). As an electron shuttle, Fe (III) improved the efficiency of electron transfer, and Fe (II) and nano-zerovalent iron (nZVI) particles were formed during this process. X-ray diffraction and transmission electron microscopy analyses showed that FeOCl was formed under the action of the plant extract and adsorbed Cr (III), thus reducing total chromium. Both nZVI and FeOCl were covered with a layer of paste cap, which maintained the stability of their physical and chemical properties. The regulation of pH during the repair process was not required, and the cost of the process was significantly reduced. Therefore, this technology provides a new strategy for the in situ remediation of Cr (VI) pollution in groundwater.

A systematic review on adsorptive removal of hexavalent chromium from aqueous solutions: Recent advances

The contamination of natural resources by hexavalent chromium (Cr(VI)) originating from natural and anthropogenic activities is a serious environmental concern. Although many articles on chromium remediation have been published, a comprehensive understanding of the mechanisms involved in remediation with different sorbents is not yet available. In this systematic review, the performance and applicability of several adsorptive materials for Cr(VI) removal from aqueous media are discussed, along with a detailed analysis of the mechanisms involved. Statistical analysis is applied to compare the efficacies of different adsorbents, while a similar approach is used to determine the effects of sorbent properties and experimental conditions on the adsorption capacity. A detailed analysis of the factors involved in fixed-bed column studies is also presented. A suitable desorption approach to the regeneration of the spent adsorbent and its adsorption performance in reuse is also examined. Among the different sorbents, nanoparticles and mineral-doped biochar were found to be the most effective sorbents, while the adsorption was higher at low pH (~4.0) than that at intermediate pH (6-8). Contrary to our expectation, adsorption was high for sorbents with low specific surface areas, suggesting that the adsorption of Cr(VI) is largely influenced by the chemical properties of the sorbents. The optimum adsorption in fixed-bed column systems is obtained at a lower Cr(VI) ion concentration, a lower influent flow rate, and a higher bed height. Since most of the studies reviewed herein were merely experimental and utilized ideal conditions with the presence of a single contaminant, i.e. Cr(VI) in water, further studies on adsorption dynamics with the presence of other interfering ions are suggested. This review is promising for the further development of Cr(VI) removal strategies and closes the research gaps pertaining to their challenges.

Facile Synthesis of Magnetic Biochar Derived from Burley Tobacco Stems towards Enhanced Cr (VI) Removal: Performance and Mechanism

In this study, ferric-loaded magnetic burley tobacco stem biochar (MBTS) was synthesized via pyrolysis to improve the removal of Cr(VI). The results showed that MBTS had an adsorption capacity of 54.92 mg Cr(VI)/g, which was about 14 times higher than raw burley tobacco stem biochar (i.e., 3.84 mg/g). According to the findings obtained, a three-step mechanism of Cr(VI) removal by MBTS was further put forward, i.e., (1) Cr(VI) exchanged with hydroxyl groups on MBTS, (2) the reduction in Cr(VI) to Cr(III) mediated by oxygen-containing groups, and (3) the chelation of produced Cr(III) with the amino groups on MBTS. FTIR spectra further revealed that C-N, C-H, and C=C groups played an important role in Cr(VI) removal. Furthermore, the adsorption equilibrium and kinetics of Cr(VI) on MBTS could better be described by the Langmuir equation and pseudo-second-order rate equation. This study clearly demonstrated that ferric-loaded biochar derived from burley tobacco stems could serve as a cost-effective magnetic adsorbent for the high-efficiency removal of soluble Cr(VI) from wastewater. Tobacco stem-adsorbed Cr(VI) realized a green path for treating waste by waste.

Process enhancing strategies for the reduction of Cr(VI) to Cr(III) via photocatalytic pathway

This discourse aimed at providing insight into the strategies that can be adopted to boost the process of photoreduction of Cr(VI) to Cr(III). Cr(VI) is amongst the highly detestable pollutants; thus, its removal or reduction to an innocuous and more tolerable Cr(III) has been the focus. The high promise of photocatalysis hinged on the sustainability, low cost, simplicity, and zero sludge generation. Consequently, the present dissertation provided a comprehensive review of the process enhancement procedures that have been reported for the photoreduction of Cr(VI) to Cr(III). Premised on the findings from experimental studies on Cr(VI) reductions, the factors that enhanced the process were identified, dilated, and interrogated. While the salient reaction conditions for the process optimization include the degree of ionization of reacting medium, available photogenerated electrons, reactor ambience, type of semiconductors, surface area of semiconductor, hole scavengers, quantum efficiency, and competing reactions, the relevant process variables are photocatalyst dosage, initial Cr(VI) concentration, interfering ion, and organic load. In addition, the practicability of photoreduction of Cr(VI) to Cr(III) was explored according to the potential for photocatalyst recovery, reactivation, and reuse reaction conditions and the process variables.

Magnetic Adsorbents for Wastewater Treatment: Advancements in Their Synthesis Methods

The remediation of water streams, polluted by various substances, is important for realizing a sustainable future. Magnetic adsorbents are promising materials for wastewater treatment. Although numerous techniques have been developed for the preparation of magnetic adsorbents, with effective adsorption performance, reviews that focus on the synthesis methods of magnetic adsorbents for wastewater treatment and their material structures have not been reported. In this review, advancements in the synthesis methods of magnetic adsorbents for the removal of substances from water streams has been comprehensively summarized and discussed. Generally, the synthesis methods are categorized into five groups, as follows: direct use of magnetic particles as adsorbents, attachment of pre-prepared adsorbents and pre-prepared magnetic particles, synthesis of magnetic particles on pre-prepared adsorbents, synthesis of adsorbents on preprepared magnetic particles, and co-synthesis of adsorbents and magnetic particles. The main improvements in the advanced methods involved making the conventional synthesis a less energy intensive, more efficient, and simpler process, while maintaining or increasing the adsorption performance. The key challenges, such as the enhancement of the adsorption performance of materials and the design of sophisticated material structures, are discussed as well.

Electroconductive and photoactive poly(phenylenediamine)s with antioxidant and antimicrobial activities for potential photothermal therapy

In recent years, polyaniline derivatives such as poly(phenylenediamine)s have attracted the attention of researchers due to their better solubility, good optical and electrical properties. In the current work, poly(ortho- phenylenediamine)...

Outstanding performance of sulfurated titanomaghemite (Fe2TiO5) for hexavalent chromium removal: Sulfuration promotion mechanism and its application in chromium resource recovery

A lot of magnetic sorbents have been developed to meet the current demand for removing Cr (VI) from wastewater. However, the application of magnetic sorbents remains restricted by the unsatisfactory Cr (VI) removal efficiency, sorbent regeneration, and safe disposition of adsorbed Cr species. In this study, magnetic titanomaghemite (Fe₂TiO₅) was sulfurated with gaseous H₂S to improve its Cr (VI) removal efficiency. Sulfuration significantly improved the Cr (VI) removal efficiency of Fe₂TiO₅ from 3%-14% to 27%-82% at pH 4-10 due to drastically increased the electrostatic adsorption of Cr (VI) and heterogeneous reduction of adsorbed Cr (VI) to Cr (III). Furthermore, the sulfurated Fe₂TiO₅ recovered using magnetic separation can be regenerated by re-sulfuration without degrading the Cr (VI) removal efficiency, therefore, sulfurated Fe₂TiO₅ can be recycled for Cr (VI) removal after the regeneration. Moreover, Cr (VI) in aqueous solution can be enriched on sulfurated Fe₂TiO₅ after multiple adsorptions in the form of Cr₂O₃ in a content of more than 30% what can be considered as a source of chrome ore. Therefore, sulfurated Fe₂TiO₅ may be a promising, low-cost, and environment-friendly sorbent for Cr recovery as a co-benefit of Cr (VI) removal from wastewater.

Engineering of appropriate pore size combined with sulfonic functionalization in a Zr-MOF with reo topology for the ultra-high removal of cationic malachite green dye from an aqueous medium

A Zr-based metal–organic framework with reo topology, denoted as Reo-MOF-1, was fabricated through a solvothermal method capable of efficiently removing the cationic MG dye from an aqueous medium.

Self-Assembled Silver Nanoparticles Decorated on Exfoliated Graphitic Carbon Nitride/Carbon Sphere Nanocomposites as a Novel Catalyst for Catalytic Reduction of Cr(VI) to Cr(III) from Wastewater and Reuse for Photocatalytic Applications

Silver nanoparticles decorated on an exfoliated graphitic carbon nitride/carbon sphere (AgNP/Eg-C₃N₄/CS) nanocomposites were synthesized by an adsorption method with a self-assembled process. These nanoparticles were characterized by different techniques like UV-visible (UV-vis) spectroscopy, photoluminescence (PL) spectroscopy, Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), thermal gravimetric analysis (TGA), Raman spectroscopy, scanning electron spectroscopy (SEM), transmission electron spectroscopy (TEM), electrochemical impedance spectroscopy (EIS), and ζ potential. AgNP/Eg-C₃N₄/CS nanocomposites showed a higher catalytic reduction activity for the conversion of Cr(VI) into Cr(III) with formic acid (FA) at 45 °C when compared to bulk graphitic carbon nitride (Bg-C₃N₄, Eg-C₃N₄, CS, and Eg-C₃N₄/CS). The kinetic rate constants were determined as a function of catalyst dosage, concentration of Cr(VI), pH, and temperature for the AgNP/Eg-C₃N₄/CS nanocomposite. This material showed higher reduction efficiency (98.5%, k = 0.0621 min^-1) with turnover frequency (0.0158 min^-1) for the reduction of Cr(VI) to Cr(III). It also showed great selectivity and high stability after six repeated cycles (98.5%). Further, the reusability of the Cr(III)-AgNP/Eg-C₃N₄/CS nanocomposite was also investigated for the photocatalytic degradation of methylene blue (MB) under visible light irradiation with various time intervals and it showed good degradation efficiency (α = 97.95%). From these results, the AgNP/Eg-C₃N₄/CS nanocomposite demonstrated higher catalytic activity, improved environmental friendliness, lower cost for the conversion of toxic Cr(VI) to Cr(III) in solutions, and also good reusability.

Hypothermia Pseudomonas taiwanensis J488 exhibited strong tolerance capacity to high dosages of divalent metal ions during nitrogen removal process

The nitrogen metabolic pathways of Pseudomonas taiwanensis J488 have not been confirmed from genomic function analysis and its divalent metal ion resistance remains poorly understood. In this study, the key denitrifying gene of Pseudomonas taiwanensis J488, nirB, was determined by draft genome sequencing. The nitrification of ammonium was insensitive to high concentrations of Ca(II), Mn(II), Zn(II), and Cd(II). Similarly, complete nitrite removal was achieved despite Mn(II) and Zn(II) reaching concentrations up to 30 mg/L. Furthermore, the efficiency of nitrate removal was significantly enhanced by 1.33%, 3.33%, 5.99%, and 1.53% with the addition of 0.5 mg/L Ca(II), 20 mg/L Mn(II), 5 mg/L Zn(II), and 2 mg/L Cd(II), respectively, comparison with the control. The bacterial growth in both nitrifying and denitrifying processes was substantially promoted by various dosages of divalent metal ions. These results indicate that divalent metal ions would not severely limit the capacity of strain J488 to purify nitrogen-polluted wastewater.