Performance Improvement of Polysulfone Ultrafiltration Membrane Using Well-Dispersed Polyaniline–Poly(vinylpyrrolidone) Nanocomposite as the Additive

Catalyst- and Stabilizer-Free Rational Synthesis of Ionic Polymer Nanoparticles in One Step for Oil/Water Separation Membranes

Ionic polymer nanoparticles (IPNs) were synthesized in one pot by quaternization precipitation polymerization (QPP) as a novel polymerization technique. QPP eliminated the usage of high-cost ionic monomers and reduced the number of steps for the preparation of IPN. The monomers 2-(dimethylamino)ethyl methacrylate (DMAEMA) and 4-vinylbenzyl chloride (VBC) polymerized in the presence of azobisisobutyronitrile (AIBN) and underwent quaternization simultaneously, which yielded ionic poly(DMAEMA-co-VBC) nanoparticles in one step with the size of 50-80 nm without any stabilizer and catalyst. Similarly, 4-vinylpyridine (VP) and VBC polymerized in the presence of AIBN and underwent quaternization simultaneously, which yielded ionic poly(VP-co-VBC) nanoparticles in one step with the size of 70-90 nm without any stabilizer and catalyst. The as-synthesized IPN was further utilized for the fabrication of hydrophilic nanocomposite ultrafiltration membranes for oil/water separation. Fabricated hybrid membranes were characterized and studied for oil rejection properties. It exhibited an oil rejection of >96% with a pure water permeability of 219 L/m² h bar.

Conducting Polyaniline for Antifouling Ultrafiltration Membranes: Solutions and Challenges

Conjugated polyaniline can impact the field of water filtration membranes due to its hydrophilic and antibacterial nature, facile and inexpensive synthesis procedure, heat and acid tolerance, and unique doping/dedoping chemistry. However, the gelation effect, its rigid backbone, and the limited hydrophilicity of polyaniline severely restrict the adaptability to membranes and their antifouling performance. This Mini Review summarizes important works of polyaniline-related ultrafiltration membranes, highlighting solutions to conquer engineering obstacles in processing and challenges in enhancing surface hydrophilicity with an emphasis on chemistry. As a pH-responsive polymer convertible to a conductive salt, this classic material should continue to bring unconventional advances into the realm of water filtration membranes.

Preparation and Application of Palladium Nanoparticle Impregnated Chloromethylated Polysulfone Matrix as an Efficient Catalytic Membrane for Oxidation of Alcohols

The use of palladium nanoparticles embedded in a chloromethylated Polysulfone (CMPSf) matrix was developed for highly efficient oxidation of primary and secondary alcohols to corresponding aldehyde and ketone in organic solvent free condition. Pd (Π)/bis (2, 4-dihydroxybenzaldehyde) chelate chemically incorporated onto CMPSf was used to prepare beneficial catalytic membranes. Chemical structure and thermal properties of resulting membranes were characterized via FTIR, 1HNMR, UV-vis, TGA and DSC techniques. Morphology and particle distribution throughout the catalytic membranes was elucidated using FE-SEM. An average particle size of Pd nanoparticles was estimated about 20 nm by XRD technique. ICP technique proved that no Pd particles were leached out of the membrane into the solutions; hence the as-prepared catalytic membranes could be used several times without significant loss in their activities. This is in good accordance with formation of chemical bond between Pd and polymer matrix.

A novel Polysulfone/Iron-Nickel oxide nanocomposite membrane for removal of heavy metal and protein from water

Making a nanocomposite membrane is an effective way of producing membranes with desired functionality, better permeance. In this work, virgin polysulfone ultrafiltration (UF) membrane and nanocomposite membranes with different concentrations ranging from 100 to 2,000 mg/L iron-nickel oxide in polysulfone matrix were prepared by phase inversion method. The performances of prepared membranes were evaluated by pure water permeance testing, protein rejection, and lead rejection. Up to 99.66% removal of lead was achieved by nanocomposite membrane. The structure and property of membranes were analyzed by scanning electron microscopy (SEM), powder X-ray diffractometer (XRD), and atomic force microscopy (AFM) and zeta potential analysis. The nanocomposite membranes showed higher water permeance as compared to virgin ultrafiltration membrane. The membrane with 750 mg/L concentration of iron-nickel oxide nanoparticle demonstrated the increase in water flux by 117.85% as compared to the virgin ultrafiltration membrane. Higher albumin rejection and lead rejection were achieved by nanocomposite membrane as compared to polysulfone membrane. Leaching study of nanomaterial in water was undertaken, and it was found the leaching of nanomaterial was minimal. Increase in surface roughness, increase in number of pores with decrease in pore size, led to improvement in ultrafiltration performance by increased selectivity and permeance of the membrane. © 2020 Water Environment Federation PRACTITIONER POINTS: The nanocomposite ultrafiltration membrane with iron-nickel oxide nanomaterial. Upto 117.85% increase in pure water permeance as compared to virgin membrane. Upto 99.66% lead rejection and upto 96.8% albumin rejection from aqueous solution. Little or no leaching of nanomaterials in water. Increased selectivity and productivity of membrane.

Applications of tannic acid in membrane technologies: A review

Today, membrane technologies play a big role in chemical industry, especially in separation engineering. Tannic acid, one of the most famous polyphenols, has attracted widespread interest in membrane society. In the past several years, researches on the applications of tannic acid in membrane technologies have grown rapidly. However, there has been lack of a comprehensive review for now. Here, we summarize the recent developments in this field for the first time. We comb the history of tannic acid and introduce the properties of tannic acid firstly, and then we turn our focus onto the applications of membrane surface modification, interlayers and selective layers construction and mixed matrix membrane development. In those previous works, tannic acid has been demonstrated to be capable of making a great contribution to the membrane science and technology. Especially in membrane surface/interface engineering (such as the construction of superhydrophilic and antifouling surfaces and polymer/nanoparticle interfaces with high compatibility) and development of thin film composite membranes with high permselectivity (such as developing thin film composite membranes with ultrahigh flux and high rejection), tannic acid can play a positive and great role. Despite this, there are still many critical challenges lying ahead. We believe that more exciting progress will be made in addressing these challenges in the future.

Integration of PEGylated Polyaniline Nanocoatings with Multiple Plastic Substrates Generates Comparable Antifouling Performance

Conducting polymer nanocoatings render plastics to possess interesting optical, chemical, and electrical properties. It nevertheless remains technically challenging to deposit uniform conducting polymer nanocoatings on ambient plastic substrates ascribed to the inert and varied chemical properties of plastics and the notorious processability of conducting polymers. Previous studies have made progress in delivering various conducting polymer thin films via oxidative chemical vapor deposition. Herein, we develop a solution-based approach to polyaniline (PANI) and PEGylated PANI nanocoatings on multiple engineering plastics followed by evaluating their antifouling performance. The procedure relies on the formation of uniform, lyotropic V₂O₅·nH₂O thin films on plastics assisted by a surfactant-sodium N-lauroylsarcosinate. Next, in situ, oxidative polymerization causes the formation of nanofibrous PANI nanocoatings. Finally, interfacial functionalization leads to PEGylated PANI nanocoatings, and the steric nanolayer effectively repels the adsorption of bovine serum albumin and the attachment of the bacterium Pseudoalteromonas sp. on the surface. It is worth noting that the antifouling properties rely mainly on the presence of PEGylated PANI nanocoatings, irrespective of the type of plastic substrates underneath. The current study therefore opens an avenue for the solution-based delivery of conducting polymer-based, functional nanocoatings on hydrophobic substrates in a controllable manner with the availability of further modification.

High-flux ultrafiltration membrane with open porous hydrophilic structure using dual pore formers

This work investigated the synergistic effect of polyvinylpyrrolidone (PVP) and hydroxypropyl-beta-cyclodextrin (HP-β-CD) as dual pore forming agents on the properties and performance of polysulfone (PSf) ultrafiltration membranes. A fixed concentration of PVP and varying concentrations of HP-β-CD were used to prepare the membranes using the phase inversion technique. The results showed that the inclusion of these additives in the dope solution increased its thermodynamic instability and promoted instantaneous demixing. Overall, an increase was observed in the hydrophilicity, open porous structure and mechanical strength of the membranes. Cross-flow filtration tests demonstrated that the pure water permeability of the fabricated membrane was 891 LMH bar^-1, about 4.37 times higher than the pristine membrane, while bovine serum albumin (BSA) rejection was relatively constant (about 93%) for all the fabricated membranes. This work proposed that the addition of HP-β-CD and PVP as dual pore formers can produce a viable ultrafiltration membrane with improved water permeability without a middle ground on rejection potential.

Effect of Unbleached Rice Straw Cellulose Nanofibers on the Properties of Polysulfone Membranes

In addition to their lower cost and more environmentally friendly nature, cellulose nanofibers isolated from unbleached pulps offer different surface properties and functionality than those isolated from bleached pulps. At the same time, nanofibers isolated from unbleached pulps keep interesting properties such as hydrophilicity and mechanical strength, close to those isolated from bleached pulps. In the current work, rice straw nanofibers (RSNF) isolated from unbleached neutral sulfite pulp (lignin content 14%) were used with polysulfone (PSF) polymer to make membrane via phase inversion. The effect of RSNF on microstructure, porosity, hydrophilicity, mechanical properties, water flux, and fouling of PSF membranes was studied. In addition, the prepared membranes were tested to remove lime nanoparticles, an example of medium-size nanoparticles. The results showed that using RSNF at loadings from 0.5 to 2 wt.% can significantly increase hydrophilicity, porosity, water flux, and antifouling properties of PSF. RSNF also brought about an increase in rejection of lime nanoparticles (up to 98% rejection) from their aqueous suspension, and at the same time, with increasing flux across the membranes. Tensile strength of the membranes improved by ~29% with addition of RSNF and the maximum improvement was obtained on using 0.5% of RSNF, while Young’s modulus improved by ~40% at the same RSNF loading. As compared to previous published results on using cellulose nanofibers isolated from bleached pulps, the obtained results in the current work showed potential application of nanofibers isolated from unbleached pulps for improving important properties of PSF membranes, such as hydrophilicity, water flux, rejection, and antifouling properties.

Preparation of Highly Porous Polymer Membranes with Hierarchical Porous Structures via Spinodal Decomposition of Mixed Solvents with UCST Phase Behavior

The predominant method to prepare polymer membranes is based on phase inversion. However, this method always leads to a dense skin with low porosity when normal polymers are used. Using the self-assembly of certain block copolymers, it is possible to prepare uniform pores with high porosity, but the prices of these polymers are too high to be afforded in practical applications. Here, we report a novel strategy to prepare highly porous and asymmetric polymer membranes using the widely used poly(vinylidene fluoride) (PVDF) as a prototype. The method combines spinodal decomposition with phase inversion utilizing mixed solvents that have the unique upper critical solution temperature phase behavior. The spinodal decomposition generates a thin surface layer containing a high density of relatively uniform pores in the mesoporous range, and the phase inversion generates a thick bulk layer composed of macrovoids; the two types of structures are interconnected, yielding a highly permeable, selective, and mechanically strong porous membrane. The membranes show an order of magnitude higher water permeance than commercial membranes and efficient molecular sieving of macromolecules. Notably, our strategy provides a general toolbox to prepare highly porous membranes from normal polymers. By blending PVDF with cellulose acetate (CA), a highly porous PVDF/CA membrane was prepared and showed similarly high separation performance, but the higher hydrophilicity of CA improved the membrane flux in the presence of proteins.

Removal of metal ions and humic acids through polyetherimide membrane with grafted bentonite clay

Functional surfaces and polymers with branched structures have a major impact on physicochemical properties and performance of membrane materials. With the aim of greener approach for enhancement of permeation, fouling resistance and detrimental heavy metal ion rejection capacity of polyetherimide membrane, novel grafting of poly (4-styrenesulfonate) brushes on low cost, natural bentonite was carried out via distillation-precipitation polymerisation method and employed as a performance modifier. It has been demonstrated that, modified bentonite clay exhibited significant improvement in the hydrophilicity, porosity, and water uptake capacity with 3 wt. % of additive dosage. SEM and AFM analysis showed the increase in macrovoides and surface roughness with increased additive concentration. Moreover, the inclusion of modified bentonite displayed an increase in permeation rate and high anti-irreversible fouling properties with reversible fouling ratio of 75.6%. The humic acid rejection study revealed that, PEM-3 membrane having rejection efficiency up to 87.6% and foulants can be easily removed by simple hydraulic cleaning. Further, nanocomposite membranes can be significantly employed for the removal of hazardous heavy metal ions with a rejection rate of 80% and its tentative mechanism was discussed. Conspicuously, bentonite clay-bearing poly (4-styrenesulfonate) brushes are having a synergistic effect on physicochemical properties of nanocomposite membrane to enhance the performance in real field applications.

Mixed-matrix membranes with enhanced antifouling activity: probing the surface-tailoring potential of Tiron and chromotropic acid for nano-TiO2

Mixed-matrix membranes (MMMs) were developed by impregnating organofunctionalized nanoadditives within fouling-susceptible polysulfone matrix following the non-solvent induced phase separation (NIPS) method. The facile functionalization of nanoparticles of anatase TiO₂ (nano-TiO₂) by using two different organoligands, viz. Tiron and chromotropic acid, was carried out to obtain organofunctionalized nanoadditives, F_T-nano-TiO₂ and F_C-nano-TiO₂, respectively. The structural features of nanoadditives were evaluated by X-ray diffraction, X-ray photoelectron spectroscopy, Raman and Fourier transform infrared spectroscopy, which established that Tiron leads to the blending of chelating and bridging bidentate geometries for F_T-nano-TiO₂, whereas chromotropic acid produces bridging bidentate as well as monodentate geometries for F_C-nano-TiO₂. The surface chemistry of the studied membranes, polysulfone (Psf): F_T-nano-TiO₂ UF and Psf: F_C-nano-TiO₂ UF, was profoundly influenced by the benign distributions of the nanoadditives enriched with distinctly charged sites ([Formula: see text]), as evidenced by superior morphology, improved topography, enhanced surface hydrophilicity and altered electrokinetic features. The membranes exhibited enhanced solvent throughputs, viz. 3500-4000 and 3400-4300 LMD at 1 bar of transmembrane pressure, without significant compromise in their rejection attributes. The flux recovery ratios and fouling resistive behaviours of MMMs towards bovine serum albumin indicated that the nanoadditives could impart stable and appreciable antifouling activity, potentially aiding in a sustainable ultrafiltration performance.

Metalized Nanocellulose Composites as a Feasible Material for Membrane Supports: Design and Applications for Water Treatment

Herein, we study the feasibility of using nanocellulose (NC)-based composites with silver and platinum nanoparticles as additive materials to fabricate the support layer of thin film composite (TFC) membranes for water purification applications. In brief, the NC surface was chemically modified and then was decorated with silver and platinum nanoparticles, respectively, by chemical reduction. These metalized nanocellulose composites (MNC) were characterized by several techniques including: FTIR, XPS, TGA, XRD, and XANES to probe their integrity. Thereafter, we fabricated the MNC-TFC membranes and the support layer was modified to improve the membrane properties. The membranes were thoroughly characterized, and the performance was evaluated in forward osmosis (FO) mode with various feed solutions: nanopure water, urea, and wastewater samples. The fabricated membranes exhibited finger-like pore morphologies and varying pore sizes. Interestingly, higher water fluxes and solute rejection was obtained with the MNC-TFC membranes with wastewater samples. The overall approach of this work provides an effort to fabricated membranes with high water flux and enhanced selectivity.

Preparation of organic–inorganic hybrid membranes with superior antifouling property by incorporating polymer-modified multiwall carbon nanotubes

Schematic illustration of (a) the polymerization of dopamine, and (b) preparation of the PVP-modified MWCNTs.

Surface zwitterionicalization of poly(vinylidene fluoride) membranes from the entrapped reactive core-shell silica nanoparticles

We demonstrate the preparation and properties of poly(vinylidene fluoride) (PVDF) filtration membranes modified via surface zwitterionicalization mediated by reactive core-shell silica nanoparticles (SiO2 NPs). The organic/inorganic hybrid SiO2 NPs grafted with poly(methyl meth acrylate)-block-poly(2-dimethylaminoethyl methacrylate) copolymer (PMMA-b-PDMAEMA) shell were prepared by surface-initiated reversible addition fragmentation chain transfer (SI-RAFT) polymerization and then used as a membrane-making additive of PVDF membranes. The PDMAEMA exposed on membrane surface and pore walls were quaternized into zwitterionic poly(sulfobetaine methacrylate) (PSBMA) using 1,3-propane sultone (1,3-PS) as the quaternization agent. The membrane surface chemistry and morphology were analyzed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), respectively. The hydrophilicity, permeability and antifouling ability of the investigated membranes were evaluated in detail. It was found that the PSBMA chains brought highly-hydrophilic and strong fouling resistant characteristics to PVDF membranes due to the powerful hydration of zwitterionic surface. The SiO2 cores and PMMA chains in the hybrid NPs play a role of anchors for the linking of PSBMA chains to membrane surface. Compared to the traditional strategies for membrane hydrophilic modification, the developed method in this work combined the advantages of both blending and surface reaction.

Carbon Nanotube/Alumina/Polyethersulfone Hybrid Hollow Fiber Membranes with Enhanced Mechanical and Anti-Fouling Properties

Carbon nanotubes (CNTs) were incorporated into alumina/polyethersulfone hollow fibre membranes to enhance the mechanical property and the efficiency of water treatment. Results show that the incorporation of CNTs can greatly limit the formation of large surface pores, decrease the void size in support layers and improve the porosity and pore connectivity of alumina/polyethersulfone membranes. As a result of such morphology change and pore size change, both improved flux and rejection were achieved in such CNTs/alumina/polyethersulfone membranes. Moreover, the CNTs/alumina/PES membranes show higher antifouling ability and the flux recoveries after being fouled by bovine serum albumin (BSA) and humic acid were improved by 84.1% and 53.2% compared to the samples without CNT incorporation. Besides the improvement in water treatment performance, the incorporation of CNTs enhanced the tensile properties of inorganic/polymer membranes. Therefore, such CNTs/alumina/PES hollow fiber membranes are very promising candidates for good filter media in industry, considering their high efficiency and high mechanical properties.

Preparation, characterization and the effect of PANI coated TiO2 nanocomposites on the performance of polysulfone ultrafiltration membranes

The PANI coated TiO₂ nanotubes serve as effective additives for polysulfone membranes, for improving their properties.

Preparation and characterization of a polyethersulfone/polyaniline nanocomposite membrane for ultrafiltration and as a substrate for a gas separation membrane

PES/PANI nanocomposite membrane displayed excellent flux and antifouling property for UF. Meanwhile, PES/PANI non-woven fabrics supported membrane performed as a suitable substrate for gas separation membrane with PVAm selective layer.

Removal of aqueous Hg(II) and Cr(VI) using phytic acid doped polyaniline/cellulose acetate composite membrane

Conductive composite membrane-phytic acid (PA) doped polyaniline (PANI)/cellulose acetate (CA) (PANI-PA/CA) was prepared in a simple and environmental-friendly method, in which aniline was blended with CA/PA solution and polymerized before the phase conversion. The resultant composite membranes were characterized by SEM, EDX, FTIR-ATR, BET and electrical resistance measurements. When used as adsorbent for Hg(II) and Cr(VI) ions, the prepared composite membrane exhibits excellent adsorption capability. The adsorption of Hg(II) and Cr(VI) follows a pseudo-second-order kinetic model and best fits the Langmuir isotherm model, with the maximum adsorption capacity reaching 280.11 and 94.34 mg g(-1), respectively. The heavy metal loaded composite membrane can be regenerated and reused after treatment with acid or alkali solution, making it a promising and practical adsorbent for Hg(II) and Cr(VI) removal. Tests with river water were also carried out, indicating good performance and application.