Electrochemical Catalyst–Support Effects and Their Stabilizing Role for IrOx Nanoparticle Catalysts during the Oxygen Evolution Reaction

CuNi alloy anchored on dual-substrate TiOx/N-doped carbon nanofibers as a bifunctional electrocatalyst for rechargeable zinc-air batteries

Development of non-noble metal-based electrocatalysts to enhance the performance of zinc-air batteries (ZABs) is of great significance, but it remains a formidable challenge due to their poor stability and activity. Herein, a bifunctional CuNi-TiOx/NCNFS electrocatalyst, featuring with electron-rich copper-nickel (CuNi) alloy nanoparticles anchored on titanium oxide/N-doped carbon nanofibers (TiOx/NCNFS), is constructed by a dual-substrate loading strategy. The introduction of TiOx has led to a significant increase in the stability of the dual-substrate. The strong electronic interaction between CuNi and TiOx strengthens the anchoring of active metal sites, thus accelerating the electron transfer. Theoretical calculations unclose that NCNFS can regulate the charge distribution of TiOx, inducing the charge transfer from NCNFS → TiOx → CuNi, thereby reducing the d-band center of Cu and Ni, which is beneficial to the desorption of intermediate oxide species of the oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Therefore, CuNi-TiOx/NCNFS delivers a remarkable bifunctional performance with a low OER overpotential of 258 mV at 10 mA cm-2 and an ORR half-wave potential of 0.85  V. When assembled into ZABs, CuNi-TiOx/NCNFS shows a low potential gap of 0.64 V, a higher power density of 149.6 mW cm-2 at 330 mA cm-2, and an outstanding stability for 250 h at 5mA cm-2. This study provides a novel approach by constructing dual-substrate to tune the electronic structure of active metal sites for efficient rechargeable ZABs.

Recent Advances in Iridium-based Electrocatalysts for Acidic Electrolyte Oxidation

Ongoing research to develop advanced electrocatalysts for the oxygen evolution reaction (OER) is needed to address demand for efficient energy conversion and carbon-free energy sources. In the OER process, acidic electrolytes have higher proton concentration and faster response than alkaline ones, but their harsh strongly acidic environment requires catalysts with greater corrosion and oxidation resistance. At present, iridium oxide (IrO2) with its strong stability and excellent catalytic performance is the catalyst of choice for the anode side of commercial PEM electrolysis cells. However, the scarcity and high cost of iridium (Ir) and the unsatisfactory activity of IrO2 hinder industrial scale application and the sustainable development of acidic OER catalytic technology. This highlights the importance of further research on acidic Ir-based OER catalysts. In this review, recent advances in Ir-based acidic OER electrocatalysts are summarized, including fundamental understanding of the acidic OER mechanism, recent insights into the stability of acidic OER catalysts, highly efficient Ir-based electrocatalysts, and common strategies for optimizing Ir-based catalysts. The future challenges and prospects of developing highly effective Ir-based catalysts are also discussed.

Facile synthesis of AuIr alloy nanoparticles and their enhanced oxygen evolution reaction performance under acidic and alkaline conditions

The development of electrocatalysts that can maintain high reactivity and stability over a wide pH range during electrolysis reactions is essential for the realization of a clean hydrogen energy society. Herein, we report the synthesis of AuIr alloy nanoparticles (NPs) with an excellent oxygen evolution reaction (OER) performance over a wide pH range. The NPs were synthesized via an antisolvent crystallization-based method and maintained their small sizes regardless of adjustments in the ratio of the Au/Ir precursor. AuIr/C exhibited low overpotential and good long-term stability under acidic and alkaline conditions compared with the Ir/C and commercial RuO2. The enhanced OER performance of AuIr/C was attributed to efficient charge transfer, resulting in an optimal synergistic effect of electrons.

Symmetric Catalyst Design Employing Ir Nanoparticles on Black WO3- x Nanofiber Support for Boosting Water Electrolysis

The efficient evolution of gaseous hydrogen and oxygen from water is required to realize sustainable energy conversion systems. To address the sluggish kinetics of the multielectron transfer reaction, bifunctional catalyst materials for both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) should be developed. Herein, a tailored combination of atomically minimized iridium catalysts and highly conductive black WO3- x nanofiber supports are developed for the bifunctional electrolyzer system. Atomic Ir catalysts, particularly those that activate the OER, minimize the utilization of precious metals. The oxygen-deficient black WO3- x NF support, which boosts the HER, offers increased electronic conductivity and favorable nucleation sites for Ir loading. The Ir-black WO3- x NFs exhibit increased double-layer capacitance, a significantly reduced onset potential, lower Tafel slope, and stable cyclability for both the OER and HER, compared to large-sized Ir catalysts loaded on white WO3 nanofibers. This study offers a strategy for developing an optimal catalyst material with suitable supports for high-performance and economical water electrolysis systems for achieving carbon-negative targets.

Recent Research on Iridium-Based Electrocatalysts for Acidic Oxygen Evolution Reaction from the Origin of Reaction Mechanism

As the anode reaction of proton exchange membrane water electrolysis (PEMWE), the acidic oxygen evolution reaction (OER) is one of the main obstacles to the practical application of PEMWE due to its sluggish four-electron transfer process. The development of high-performance acidic OER electrocatalysts has become the key to improving the reaction kinetics. To date, although various excellent acidic OER electrocatalysts have been widely researched, Ir-based nanomaterials are still state-of-the-art electrocatalysts. Hence, a comprehensive and in-depth understanding of the reaction mechanism of Ir-based electrocatalysts is crucial for the precise optimization of catalytic performance. In this review, the origin and nature of the conventional adsorbate evolution mechanism (AEM) and the derived volcanic relationship on Ir-based electrocatalysts for acidic OER processes are summarized and some optimization strategies for Ir-based electrocatalysts based on the AEM are introduced. To further investigate the development strategy of high-performance Ir-based electrocatalysts, several unconventional OER mechanisms including dual-site mechanism and lattice oxygen mediated mechanism, and their applications are introduced in detail. Thereafter, the active species on Ir-based electrocatalysts at acidic OER are summarized and classified into surface Ir species and O species. Finally, the future development direction and prospect of Ir-based electrocatalysts for acidic OER are put forward.

Enhancing the acidic oxygen evolution reaction performance of RuO2-TiO2by a reduction-oxidation process

As a promising alternative to Ir based acidic oxygen evolution reaction (OER) catalysts, Ru suffers from severe fading issues. Supporting it on robust oxides such as TiO2is a simple and effective way to enhance its lifetime. Here, we find that a simple reduction-oxidation process can further improve both activity and stability of RuO2-TiO2composites at high potentials. In this process, the degree of oxidation was carefully controlled to form Ru/RuO2heterostructure to improve OER activity. Moreover, due to the oxophilicity difference of Ru and Ti, the structure of catalysts was changed from supported to embedded, which enhanced the protective effect of TiO2and mitigated the dissolution of Ru element in acidic electrolyte, making as-prepared Ru/RuO2-TiO2with better durability at all tested potentials.

An IrRuOx catalyst supported by oxygen-vacant Ta oxide for the oxygen evolution reaction and proton exchange membrane water electrolysis

The sustainable development of proton exchange membrane water electrolysis (PEMWE) requires a dramatic reduction in Ir while maintaining good catalytic activity and stability for the oxygen evolution reaction (OER). Herein, high-surface-area Ta2O5 with abundant oxygen vacancies is synthesized via a facile process, followed by anchoring IrRuOx onto a Ta2O5 support (IrRuOx/Ta2O5). IrRuOx and Ta2O5 work synergistically to afford excellent catalytic performance for the acidic OER. At 0.3 mgIr cm-2, IrRuOx/Ta2O5 only needed an overpotential of 235 mV to deliver 10 mA cm-2 in an acidic half cell and needed a cell potential of 1.91 V to deliver 2 A cm-2 in a PEM water electrolyzer. The characterization results show that doping Ir into RuOx significantly improves the stability and the electrochemically active surface area of RuOx. In IrRuOx/Ta2O5, IrRuOx interacts with Ta2O5 through more electron-rich Ir, indicating strong synergy between the catalyst and the support. The use of a metal oxide support improves the catalyst dispersion, optimizes electronic structures, facilitates mass transport, and stabilizes active sites. This work demonstrates that compositing Ir with less expensive Ru and anchoring catalyst nanoparticles on platinum-group metal (PGM)-free metal oxide supports represents one of the most promising strategies to reduce Ir loading and achieve an activity-stability trade-off. Such a strategy can benefit future catalyst design for other energy storage and conventional processes.

Optimizing Edge Active Sites via Intrinsic In-Plane Iridium Deficiency in Layered Iridium Oxides for Oxygen Evolution Electrocatalysis

Improving catalytic activity of surface iridium sites without compromising catalytic stability is the core task of designing more efficient electrocatalysts for oxygen evolution reaction (OER) in acid. This work presents phase transition of a bulk layered iridate Na2IrO3 in acid solution at room temperature, and subsequent exfoliation to produce 2D iridium oxide nanosheets with around 4 nm thickness. The nanosheets consist of OH-terminated, honeycomb-type layers of edge-sharing IrO6 octahedral framework with intrinsic in-plane iridium deficiency. The nanosheet material is among the most active Ir-based catalysts reported for acidic OER and gives an iridium mass activity improvement up to a factor of 16.5 over rutile IrO2 nanoparticles. The material also exhibits good catalytic and structural stability and retains the catalytic activity for more than 1300 h. The combined experimental and theoretical results demonstrate that edge Ir sites of the layer are active centers for OER, with structural hydroxyl groups participating in the catalytic cycle of OER via a non-traditional adsorbate evolution mechanism. The existence of intrinsic in-plane iridium deficiency is the key to building a unique local environment of edge active sites that have optimal surface oxygen adsorption properties and thereby high catalytic activity.

Highly Crystalline Iridium-Nickel Nanocages with Subnanopores for Acidic Bifunctional Water Splitting Electrolysis

Developing efficient bifunctional materials is highly desirable for overall proton membrane water splitting. However, the design of iridium materials with high overall acidic water splitting activity and durability, as well as an in-depth understanding of the catalytic mechanism, is challenging. Herein, we successfully developed subnanoporous Ir3Ni ultrathin nanocages with high crystallinity as bifunctional materials for acidic water splitting. The subnanoporous shell enables Ir3Ni NCs optimized exposure of active sites. Importantly, the nickel incorporation contributes to the favorable thermodynamics of the electrocatalysis of the OER after surface reconstruction and optimized hydrogen adsorption free energy in HER electrocatalysis, which induce enhanced intrinsic activity of the acidic oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Together, the Ir3Ni nanocages achieve 3.72 A/mgIr(η=350 mV) and 4.47 A/mgIr(η=40 mV) OER and HER mass activity, which are 18.8 times and 3.3 times higher than that of commercial IrO2 and Pt, respectively. In addition, their highly crystalline identity ensures a robust nanostructure, enabling good catalytic durability during the oxygen evolution reaction after surface oxidation. This work provides a new revenue toward the structural design and insightful understanding of metal alloy catalytic mechanisms for the bifunctional acidic water splitting electrocatalysis.

Interfacial Engineering Boosting the Activity and Stability of MIL-53(Fe) toward Electrocatalytic Nitrogen Reduction

The electrochemical nitrogen reduction reaction (eNRR) has emerged as a promising strategy for green ammonia synthesis. However, it suffers unsatisfactory reaction performance owing to the low aqueous solubility of N2 in aqueous solution, the high dissociation energy of N≡N, and the unavoidable competing hydrogen evolution reaction (HER). Herein, a MIL-53(Fe)@TiO2 catalyst is designed and synthesized for highly efficient eNRR. Relative to simple MIL-53(Fe), MIL-53(Fe)@TiO2 achieves a 2-fold enhancement in the Faradaic efficiency (FE) with an improved ammonia yield rate by 76.5% at -0.1 V versus reversible hydrogen electrode (RHE). After four cycles of electrocatalysis, MIL-53(Fe)@TiO2 can maintain a good catalytic activity, while MIL-53(Fe) exhibits a significant decrease in the NH3 yield rate and FE by 79.8 and 82.3%, respectively. Benefiting from the synergetic effect between TiO2 and MIL-53(Fe) in the composites, Fe3+ ions can be greatly stabilized in MIL-53(Fe) during the eNRR process, which greatly hinders the catalyst deactivation caused by the electrochemical reduction of Fe3+ ions. Further, the charge transfer ability in the interface of composites can be improved, and thus, the eNRR activity is significantly boosted. These findings provide a promising insight into the preparation of efficient composite electrocatalysts.

Surface engineering for stable electrocatalysis

In recent decades, significant progress has been achieved in rational developments of electrocatalysts through constructing novel atomistic structures and modulating catalytic surface topography, realizing substantial enhancement in electrocatalytic activities. Numerous advanced catalysts were developed for electrochemical energy conversion, exhibiting low overpotential, high intrinsic activity, and selectivity. Yet, maintaining the high catalytic performance under working conditions with high polarization and vigorous microkinetics that induce intensive degradation of surface nanostructures presents a significant challenge for commercial applications. Recently, advanced operando and computational techniques have provided comprehensive mechanistic insights into the degradation of surficial functional structures. Additionally, various innovative strategies have been devised and proven effective in sustaining electrocatalytic activity under harsh operating conditions. This review aims to discuss the most recent understanding of the degradation microkinetics of catalysts across an entire range of anodic to cathodic polarizations, encompassing processes such as oxygen evolution and reduction, hydrogen reduction, and carbon dioxide reduction. Subsequently, innovative strategies adopted to stabilize the materials' structure and activity are highlighted with an in-depth discussion of the underlying rationale. Finally, we present conclusions and perspectives regarding future research and development. By identifying the research gaps, this review aims to inspire further exploration of surface degradation mechanisms and rational design of durable electrocatalysts, ultimately contributing to the large-scale utilization of electroconversion technologies.

Solvation enhanced long-range proton transfer in aqueous phase for glycolaldehyde hydrogenation over Ru/C catalyst

The catalytic hydrogenation of biomass-derived chemicals is essential in chemical industry due to the growing demand for sustainable and renewable energy sources. In this study, we present a comprehensive theoretical investigation regarding the hydrogenation of glycolaldehyde to ethylene glycol over a Ru/C catalyst by employing density functional theory and ab initio molecular dynamics simulations. With inclusion of explicit solvation, we have demonstrated that the glycolaldehyde hydrogenation is significantly improved due to the fast proton transfer through the hydrogen bond network. The enhanced activity could be attributed to the participation of the solvent water as the hydrogen source and the highly positively charged state of a Ru cluster in an aqueous phase, which are critical for the activation of aldehyde groups and proton-assisted hydrogenation. Overall, our findings provide valuable insights into glycolaldehyde hydrogenation over Ru/C catalysts in the aqueous phase, highlighting the importance of solvation effects in the biomass conversion.

Investigating Electrode-Ionomer Interface Phenomena for Electrochemical Energy Applications

The endeavor to develop high-performance electrochemical energy applications has underscored the growing importance of comprehending the intricate dynamics within an electrode's structure and their influence on overall performance. This review investigates the complexities of electrode-ionomer interactions, which play a critical role in optimizing electrochemical reactions. Our examination encompasses both microscopic and meso/macro scale functions of ionomers at the electrode-ionomer interface, providing a thorough analysis of how these interactions can either enhance or impede surface reactions. Furthermore, this review explores the broader-scale implications of ionomer distribution within porous electrodes, taking into account factors like ionomer types, electrode ink formulation, and carbon support interactions. We also present and evaluate state-of-the-art techniques for investigating ionomer distribution, including electrochemical methods, imaging, modeling, and analytical techniques. Finally, the performance implications of these phenomena are discussed in the context of energy conversion devices. Through this comprehensive exploration of intricate interactions, this review contributes to the ongoing advancements in the field of energy research, ultimately facilitating the design and development of more efficient and sustainable energy devices.

Electroless Deposition of Palladium Nanoparticles on Graphdiyne Boosts Electrochemiluminescence

Modulating the electronic structure of metal nanoparticles via metal-support interaction has attracted intense interest in the field of catalytic science. However, the roles of supporting substrates in regulating the catalytic properties of electrochemiluminescence (ECL) remain elusive. Here, we find that the use of graphdiyne (GDY) as the substrate for electroless deposition of Pd nanoparticles (Pd/GDY) produces the most pronounced anodic signal enhancement in luminol-dissolved oxygen (O2) ECL system as co-reactant accelerator over other carbon-based Pd composite nanomaterials. Pd/GDY exhibits electrocatalytic activity for the reduction of O2 through a four-electron pathway at approximately -0.059 V (vs Ag/AgCl) in neutral solution forming reactive oxygen species (ROS) as intermediates. The study shows that the interaction of Pd and GDY increases the amount and stability of ROS on the Pd/GDY electrode surface and promotes the reaction of ROS and luminol anion radical to generate excited luminol, which significantly boosts the luminol anodic ECL emission. Based on quenching of luminol ECL through the consumption of ROS by antioxidants, we develop a platform for the detection of intracellular antioxidants. This study provides an avenue for the development of efficient luminol ECL systems in neutral media and expands the biological application of ECL systems.

Boosting electrocatalytic performance via electronic structure regulation for acidic oxygen evolution

High-purity hydrogen produced by water electrolysis has become a sustainable energy carrier. Due to the corrosive environments and strong oxidizing working conditions, the main challenge faced by acidic water oxidation is the decrease in the activity and stability of anodic electrocatalysts. To address this issue, efficient strategies have been developed to design electrocatalysts toward acidic OER with excellent intrinsic performance. Electronic structure modification achieved through defect engineering, doping, alloying, atomic arrangement, surface reconstruction, and constructing metal-support interactions provides an effective means to boost OER. Based on introducing OER mechanism commonly present in acidic environments, this review comprehensively summarizes the effective strategies for regulating the electronic structure to boost the activity and stability of catalytic materials. Finally, several promising research directions are discussed to inspire the design and synthesis of high-performance acidic OER electrocatalysts.

A 2D Nano-architecture (NPSMC@Ir-Ru@rGO) Derived from Graphene Enfolded Polyphosphazene Nanospheres Decorated Ir-Ru Metals (PZS@Ir-Ru@GO) towards Bifunctional Water Splitting

A leap-forward approach has been successfully devised to synthesize a novel hierarchical binary metal modified heteroatom doped 2D micro-/mesporous carbon-graphene nanostructure (NPSMC@Ir-Ru@rGO) for overall water splitting application. To investigate the role of decorating metals, different electrolcatalysts like NPSMC, NPSMC@rGO, NPSMC@Ir@rGO, and NPSMC@Ru@rGO were also synthesized and structural changes were compared and investigated by physiochemical techniques. All of the samples have shown electrocatalytic activities attributed to the presence of heteroatom (N, P, S) doped micro-/mesoporous carbonaceous matrix, amorphous carbon in the coexistence of graphitic lattice carbons, presence of active metal NPs (Ir and/-or Ru), an even distribution of active sites, and graphene 2D interconnected channels to promote electron transfer ability, respectively. However, the Ir-Ru metal codeped nanocatalyst (NPCMS@Ir-Ru@rGO) is proved to be an excellent electrocatalyst based on the synergistic role of Ir-Ru metals that necessitates the low overpotentials of 181 mV and 318 mV to convey a current density of 10 mA cm-2 towards the electroctalytic application of HER and OER, respectively. Furthermore, exhibiting the corresponding Tafel slopes (132 and 70 mV dec-1 ) in an alkaline medium. This work is anticipated to open up new avenues for the development of promising electrocatalysts based on active metals modified heteroatom doped carbon nanomaterials for energy applications.

Metal Alloys-Structured Electrocatalysts: Metal-Metal Interactions, Coordination Microenvironments, and Structural Property-Reactivity Relationships

Metal alloys-structured electrocatalysts (MAECs) have made essential contributions to accelerating the practical applications of electrocatalytic devices in renewable energy systems. However, due to the complex atomic structures, varied electronic states, and abundant supports, precisely decoding the metal-metal interactions and structure-activity relationships of MAECs still confronts great challenges, which is critical to direct the future engineering and optimization of MAECs. Here, this timely review comprehensively summarizes the latest advances in creating the MAECs, including the metal-metal interactions, coordination microenvironments, and structure-activity relationships. First, the fundamental classification, design, characterization, and structural reconstruction of MAECs are outlined. Then, the electrocatalytic merits and modulation strategies of recent breakthroughs for noble and non-noble metal-structured MAECs are thoroughly discussed, such as solid solution alloys, intermetallic alloys, and single-atom alloys. Particularly, unique insights into the bond interactions, theoretical understanding, and operando techniques for mechanism disclosure are given. Thereafter, the current states of diverse MAECs with a unique focus on structural property-reactivity relationships, reaction pathways, and performance comparisons are discussed. Finally, the future challenges and perspectives for MAECs are systematically discussed. It is believed that this comprehensive review can offer a substantial impact on stimulating the widespread utilization of metal alloys-structured materials in electrocatalysis.

Flash-Thermal Shock Synthesis of High-Entropy Alloys Toward High-Performance Water Splitting

High-entropy alloys (HEAs) provide unprecedented physicochemical properties over unary nanoparticles (NPs). According to the conventional alloying guideline (Hume-Rothery rule), however, only size-and-structure similar elements can be mixed, limiting the possible combinations of alloying elements. Recently, it has been reported that based on carbon thermal shocks (CTS) in a vacuum atmosphere at high temperature, ultrafast heating/cooling rates and high-entropy environment play a critical role in the synthesis of HEAs, ruling out the possibility of phase separation. Since the CTS requires conducting supports, the Joule-heating efficiencies rely on the carbon qualities, featuring difficulties in uniform heating along the large area. This work proposes a photo-thermal approach as an alternative and innovative synthetic method that is compatible with ambient air, large-area, remote process, and free of materials selection. Single flash irradiation on carbon nanofibers induced momentary high-temperature annealing (>1800 °C within 20 ms duration, and ramping/cooling rates >104 K s-1 ) to successfully decorate HEA NPs up to nine elements with excellent compatibility for large-scale synthesis (6.0 × 6.0 cm2 of carbon nanofiber paper). To demonstrate their feasibility toward applications, senary HEA NPs (PtIrFeNiCoCe) are designed and screened, showing high activity (ηoverall = 777 mV) and excellent stability (>5000 cycles) at the water splitting, including hydrogen evolution reactions and oxygen evolution reactions.

Ir-Sn pair-site triggers key oxygen radical intermediate for efficient acidic water oxidation

The anode corrosion induced by the harsh acidic and oxidative environment greatly restricts the lifespan of catalysts. Here, we propose an antioxidation strategy to mitigate Ir dissolution by triggering strong electronic interaction via elaborately constructing a heterostructured Ir-Sn pair-site catalyst. The formation of Ir-Sn dual-site at the heterointerface and the resulting strong electronic interactions considerably reduce d-band holes of Ir species during both the synthesis and the oxygen evolution reaction processes and suppress their overoxidation, enabling the catalyst with substantially boosted corrosion resistance. Consequently, the optimized catalyst exhibits a high mass activity of 4.4 A mgIr-1 at an overpotential of 320 mV and outstanding long-term stability. A proton-exchange-membrane water electrolyzer using this catalyst delivers a current density of 2 A cm-2 at 1.711 V and low degradation in an accelerated aging test. Theoretical calculations unravel that the oxygen radicals induced by the π* interaction between Ir 5d-O 2p might be responsible for the boosted activity and durability.

Loading IrOx Clusters on MnO2 Boosts Acidic Water Oxidation via Metal-Support Interaction

Noble metal-based electrocatalysts are crucial for efficient acidic water oxidation to develop green hydrogen energy. However, traditional noble metal catalysts loaded on inactive substrates show limited intrinsic catalytic activity, and their large sizes have compromised the atom efficiency of these noble metals. Herein, IrOx nanoclusters with sizes below 2 nm, displaying high atom-utilization efficiency of Ir species, were supported on a redox-active MnO2 nanosubstrate (IrOx/MnO2) with different phases (α-MnO2, δ-MnO2, and ε-MnO2) to explore the optimal combination. Electrochemical measurements showed that IrOx/ε-MnO2 had excellent OER performance with a low overpotential of 225 mV at 10 mA cm-2 in 0.5 M H2SO4, superior to its counterpart, IrOx/α-MnO2 (242 mV) and IrOx/δ-MnO2 (286 mV). Moreover, it also delivered robust stability with no obvious change in operating potential at 10 mA cm-2 during 50 h of continuous operation. Combining the XPS results and Bader charge analysis, we demonstrated that the strong metal-support interactions of IrOx/ε-MnO2 could effectively regulate the electronic structures of the active Ir atoms and stabilize IrOx nanoclusters on supports to suppress their detachment, resulting in significantly enhanced catalytic activity and stability for acidic OER. DFT calculations further supported that the enhanced catalytic OER performance of IrOx/ε-MnO2 could be ascribed to the appropriate strength of interactions between the active Ir sites and the reaction intermediates of the potential-determining step (*O and *OOH) regulated by the redox-active substrates.

Low Ruthenium Content Confined on Boron Carbon Nitride as an Efficient and Stable Electrocatalyst for Acidic Oxygen Evolution Reaction

To date, only a few noble metal oxides exhibit the required efficiency and stability as oxygen evolution reaction (OER) catalysts under the acidic, high-voltage conditions that exist during proton exchange membrane water electrolysis (PEMWE). The high cost and scarcity of these catalysts hinder the large-scale application of PEMWE. Here, we report a novel OER electrocatalyst for OER comprised of uniformly dispersed Ru clusters confined on boron carbon nitride (BCN) support. Compared to RuO2 , our BCN-supported catalyst shows enhanced charge transfer. It displays a low overpotential of 164 mV at a current density of 10 mA cm-2 , suggesting its excellent OER catalytic activity. This catalyst was able to operate continuously for over 12 h under acidic conditions, whereas RuO2 without any support fails in 1 h. Density functional theory (DFT) calculations confirm that the interaction between the N on BCN support and Ru clusters changes the adsorption capacity and reduces the OER energy barrier, which increases the electrocatalytic activity of Ru.

Efficient and sustainable water electrolysis achieved by excess electron reservoir enabling charge replenishment to catalysts

Suppressing the oxidation of active-Ir(III) in IrOx catalysts is highly desirable to realize an efficient and durable oxygen evolution reaction in water electrolysis. Although charge replenishment from supports can be effective in preventing the oxidation of IrOx catalysts, most supports have inherently limited charge transfer capability. Here, we demonstrate that an excess electron reservoir, which is a charged oxygen species, incorporated in antimony-doped tin oxide supports can effectively control the Ir oxidation states by boosting the charge donations to IrOx catalysts. Both computational and experimental analyses reveal that the promoted charge transfer driven by excess electron reservoir is the key parameter for stabilizing the active-Ir(III) in IrOx catalysts. When used in a polymer electrolyte membrane water electrolyzer, Ir catalyst on excess electron reservoir incorporated support exhibited 75 times higher mass activity than commercial nanoparticle-based catalysts and outstanding long-term stability for 250 h with a marginal degradation under a water-splitting current of 1 A cm-2. Moreover, Ir-specific power (74.8 kW g-1) indicates its remarkable potential for realizing gigawatt-scale H2 production for the first time.

Nano-metal diborides-supported anode catalyst with strongly coupled TaOx/IrO2 catalytic layer for low-iridium-loading proton exchange membrane electrolyzer

The sluggish kinetics of oxygen evolution reaction (OER) and high iridium loading in catalyst coated membrane (CCM) are the key challenges for practical proton exchange membrane water electrolyzer (PEMWE). Herein, we demonstrate high-surface-area nano-metal diborides as promising supports of iridium-based OER nanocatalysts for realizing efficient, low-iridium-loading PEMWE. Nano-metal diborides are prepared by a novel disulphide-to-diboride transition route, in which the entropy contribution to the Gibbs free energy by generation of gaseous sulfur-containing products plays a crucial role. The nano-metal diborides, TaB2 in particular, are investigated as the support of IrO2 nanocatalysts, which finally forms a TaOx/IrO2 heterojunction catalytic layer on TaB2 surface. Multiple advantageous properties are achieved simultaneously by the resulting composite material (denoted as IrO2@TaB2), including high electrical conductivity, improved iridium mass activity and enhanced corrosion resistance. As a consequence, the IrO2@TaB2 can be used to fabricate the membrane electrode with a low iridium loading of 0.15 mg cm-2, and to give an excellent catalytic performance (3.06 A cm-2@2.0 V@80 oC) in PEMWE-the one that is usually inaccessible by unsupported Ir-based nanocatalysts and the vast majority of existing supported Ir-based catalysts at such a low iridium loading.

Dense-Packed RuO2 Nanorods with In Situ Generated Metal Vacancies Loaded on SnO2 Nanocubes for Proton Exchange Membrane Water Electrolyzer with Ultra-Low Noble Metal Loading

Proton exchange membrane water electrolyzer (PEMWE) is a green hydrogen production technology that can be coupled with intermittent power sources such as wind and photoelectric power. To achieve cost-effective operations, low noble metal loading on the anode catalyst layer is desired. In this study, a catalyst with RuO2 nanorods coated outside SnO2 nanocubes is designed, which forms continuous networks and provides high conductivity. This allows for the reduction of Ru contents in catalysts. Furthermore, the structure evolutions on the RuO2 surface are carefully investigated. The etched RuO2 surfaces are seen as the consequence of Co leaching, and theoretical calculations demonstrate that it is more effective in driving oxygen evolution. For electrochemical tests, the catalysts with 23 wt% Ru exhibit an overpotential of 178 mV at 10 mA cm-2 , which is much higher than most state-of-art oxygen evolution catalysts. In a practical PEMWE, the noble metal Ru loading on the anode side is only 0.3 mg cm-2 . The cell achieves 1.61 V at 1 A cm-2 and proper stability at 500 mA cm-2 , demonstrating the effectiveness of the designed catalyst.

Understanding the Structural Evolution of IrFeCoNiCu High-Entropy Alloy Nanoparticles under the Acidic Oxygen Evolution Reaction

High-entropy alloy (HEA) nanoparticles are promising catalyst candidates for the acidic oxygen evolution reaction (OER). Herein, we report the synthesis of IrFeCoNiCu-HEA nanoparticles on a carbon paper substrate via a microwave-assisted shock synthesis method. Under OER conditions in 0.1 M HClO₄, the HEA nanoparticles exhibit excellent activity with an overpotential of ∼302 mV measured at 10 mA cm^-2 and improved stability over 12 h of operation compared to the monometallic Ir counterpart. Importantly, an active Ir-rich shell layer with nanodomain features was observed to form on the surface of IrFeCoNiCu-HEA nanoparticles immediately after undergoing electrochemical activation, mainly due to the dissolution of the constituent 3d metals. The core of the particles was able to preserve the characteristic homogeneous single-phase HEA structure without significant phase separation or elemental segregation. This work illustrates that under acidic operating conditions, the near-surface structure of HEA nanoparticles is susceptible to a certain degree of structural dynamics.

"Nano Lab" Advanced Characterization Platform for Studying Electrocatalytic Iridium Nanoparticles Dispersed on TiOxNy Supports Prepared on Ti Transmission Electron Microscopy Grids

Aiming at speeding up the discovery and understanding of promising electrocatalysts, a novel experimental platform, i.e., the Nano Lab, is introduced. It is based on state-of-the-art physicochemical characterization and atomic-scale tracking of individual synthesis steps as well as subsequent electrochemical treatments targeting nanostructured composites. This is provided by having the entire experimental setup on a transmission electron microscopy (TEM) grid. Herein, the oxygen evolution reaction nanocomposite electrocatalyst, i.e., iridium nanoparticles dispersed on a high-surface-area TiO_xN_y support prepared on the Ti TEM grid, is investigated. By combining electrochemical concepts such as anodic oxidation of TEM grids, floating electrode-based electrochemical characterization, and identical location TEM analysis, relevant information from the entire composite's cycle, i.e., from the initial synthesis step to electrochemical operation, can be studied. We reveal that Ir nanoparticles as well as the TiO_xN_y support undergo dynamic changes during all steps. The most interesting findings made possible by the Nano Lab concept are the formation of Ir single atoms and only a small decrease in the N/O ratio of the TiO_xN_y-Ir catalyst during the electrochemical treatment. In this way, we show that the precise influence of the nanoscale structure, composition, morphology, and electrocatalyst's locally resolved surface sites can be deciphered on the atomic level. Furthermore, the Nano Lab's experimental setup is compatible with ex situ characterization and other analytical methods, such as Raman spectroscopy, X-ray photoelectron spectroscopy, and identical location scanning electron microscopy, hence providing a comprehensive understanding of structural changes and their effects. Overall, an experimental toolbox for the systematic development of supported electrocatalysts is now at hand.

Influence of Temperature on the Performance of Carbon- and ATO-supported Oxygen Evolution Reaction Catalysts in a Gas Diffusion Electrode Setup

State-of-the-art industrial electrocatalysts for the oxygen evolution reaction (OER) under acidic conditions are Ir-based. Considering the scarce supply of Ir, it is imperative to use the precious metal as efficiently as possible. In this work, we immobilized ultrasmall Ir and Ir_0.4Ru_0.6 nanoparticles on two different supports to maximize their dispersion. One high-surface-area carbon support serves as a reference but has limited technological relevance due to its lack of stability. The other support, antimony-doped tin oxide (ATO), has been proposed in the literature as a possible better support for OER catalysts. Temperature-dependent measurements performed in a recently developed gas diffusion electrode (GDE) setup reveal that surprisingly the catalysts immobilized on commercial ATO performed worse than their carbon-immobilized counterparts. The measurements suggest that the ATO support deteriorates particularly fast at elevated temperatures.

Electrocatalysts for the Oxygen Evolution Reaction in Acidic Media

The well-established proton exchange membrane (PEM)-based water electrolysis, which operates under acidic conditions, possesses many advantages compared to alkaline water electrolysis, such as compact design, higher voltage efficiency, and higher gas purity. However, PEM-based water electrolysis is hampered by the low efficiency, instability, and high cost of anodic electrocatalysts for the oxygen evolution reaction (OER). In this review, the recently reported acidic OER electrocatalysts are comprehensively summarized, classified, and discussed. The related fundamental studies on OER mechanisms and the relationship between activity and stability are particularly highlighted in order to provide an atomistic-level understanding for OER catalysis. A stability test protocol is suggested to evaluate the intrinsic activity degradation. Some current challenges and unresolved questions, such as the usage of carbon-based materials and the differences between the electrocatalyst performances in acidic electrolytes and PEM-based electrolyzers are also discussed. Finally, suggestions for the most promising electrocatalysts and a perspective for future research are outlined. This review presents a fresh impetus and guideline to the rational design and synthesis of high-performance acidic OER electrocatalysts for PEM-based water electrolysis.

Activity-Stability Trends of the Sb-SnO2@RuOx Heterostructure toward Acidic Water Oxidation

Accomplishments of enhanced activity and durability are a major concern in the design of catalysts for acidic water oxidation. To date, most studied supported metal catalysts undergo fast degradation in strongly acidic and oxidative environments due to improper controlling of the interface stability caused by their lattice mismatches. Here, we evaluate the activity-stability trends of in situ crystallized antimony-doped tin oxide (Sb-SnO₂)@RuO_x (Sb-SnO₂@RuO_x) heterostructure nanosheets (NSs) for acidic water oxidation. The catalyst prepared by atomic layer deposition of a conformal Ru film on antimony-doped tin sulfide (Sb-SnS₂) NSs followed by heat treatment highlights comparable activity but longer stability than that of the ex situ catalyst (where Ru was deposited on Sb-SnO₂ followed by heating). Air calcination for in situ crystallization allows the formation of hierarchical mesoporous Sb-SnO₂ NSs from as-prepared Sb-SnS₂ NSs and parallel in situ transformation from Ru to RuO_x, resulting in a compact heterostructure. The significance of this approach significantly resists corrosive dissolution, which is justified by the enhanced oxygen evolution reaction (OER) stability of the catalyst compared to most of the state-of-the-art ruthenium-based catalysts including Carbon@RuO_x (which shows ∼10 times higher dissolution) as well as Sb-SnO₂@Com. RuO_x and Com. RuO₂. This study demonstrates the controlled interface stability of heterostructure catalysts toward enhancing OER activity and stability.

In Situ Activation Endows Orthorhombic Fluorite-Type Samarium Iridium Oxide with Enhanced Acidic Water Oxidation

Developing electrochemical catalysts for acidic water oxidation with improved activity and stability has been the key to the further popularization of proton exchange membrane electrolyzers. In this work, an orthorhombic fluorite-type samarium iridium oxide (Sm3IrO7) catalyst is synthesized by a simple solid-state reaction. After in situ activation, the as-prepared Sm3IrO7 exhibits higher mass activity and durability than that of commercial IrO2. The in-depth analyses indicate the formation of amorphous IrOx species on the surface to evolve to a new heterostructure IrOx/Sm3IrO7, along with Sm leaching during the in situ activation process. More importantly, strong electronic interactions exist between newborn IrOx species and remaining Sm3IrO7, leading to the compressed Ir-O bonds in IrOx compared to commercial IrO2, thus reducing the energy barrier for oxygen evolution reaction (OER) intermediates to improve the OER process. Based on the above-mentioned analyses, it is speculated that the actual active species for enhanced acidic water oxidation should be IrOx/Sm3IrO7, rather than Sm3IrO7 itself. Theoretical calculations confirm that the optimal energy level path of IrOx/Sm3IrO7 follows the lattice oxygen mechanism, and the energy level of surface Ir 5d orbitals is lower than O 2p orbitals in IrOx/Sm3IrO7, enabling it a superior OER activity.

Iridium oxide nanoribbons with metastable monoclinic phase for highly efficient electrocatalytic oxygen evolution

Metastable metal oxides with ribbon morphologies have promising applications for energy conversion catalysis, however they are largely restricted by their limited synthesis methods. In this study, a monoclinic phase iridium oxide nanoribbon with a space group of C2/m is successfully obtained, which is distinct from rutile iridium oxide with a stable tetragonal phase (P42/mnm). A molten-alkali mechanochemical method provides a unique strategy for achieving this layered nanoribbon structure via a conversion from a monoclinic phase K_0.25IrO₂ (I2/m (12)) precursor. The formation mechanism of IrO₂ nanoribbon is clearly revealed, with its further conversion to IrO₂ nanosheet with a trigonal phase. When applied as an electrocatalyst for the oxygen evolution reaction in acidic condition, the intrinsic catalytic activity of IrO₂ nanoribbon is higher than that of tetragonal phase IrO₂ due to the low d band centre of Ir in this special monoclinic phase structure, as confirmed by density functional theory calculations.

Chiral electrocatalysts eclipse water splitting metrics through spin control

Continual progress in technologies that rely on water splitting are often hampered by the slow kinetics associated with the oxygen evolution reaction (OER). Here, we show that the efficiency of top-performing catalysts can be improved, beyond typical thermodynamic considerations, through control over reaction intermediate spin alignment during electrolysis. Spin alignment is achieved using the chiral induced spin selectivity (CISS) effect and the improvement in OER manifests as an increase in Faradaic efficiency, decrease in reaction overpotential, and change in the rate determining step for chiral nanocatalysts over compositionally analogous achiral nanocatalysts. These studies illustrate that a defined spatial orientation of the nanocatalysts is not necessary to exhibit spin selectivity and therefore represent a viable platform for employing the transformative role of chirality in other reaction pathways and processes.

IrO2 Nanoparticle-Decorated Ir-Doped W18O49 Nanowires with High Mass Specific OER Activity for Proton Exchange Membrane Electrolysis

The oxygen evolution reaction (OER) severely limits the efficiency of proton exchange membrane (PEM) electrolyzers due to slow reaction kinetics. IrO₂ is currently a commonly used anode catalyst, but its large-scale application is limited due to its high price and scarce reserves. Herein, we reported a practical strategy to construct an acid OER catalyst where Iridium oxide loading and iridium element bulk doping are realized on the surface and inside of W₁₈O₄₉ nanowires by immersion adsorption, respectively. Specifically, W_0.7Ir_0.3O_y has an overpotential of 278 mV at 10 mA·cm^-2 in 0.1 M HClO₄. The mass activity of 714.10 A·g_Ir^-1 at 1.53 V vs. the reversible hydrogen electrode (RHE) is 80 times that of IrO₂, and it can run stably for 55 h. In the PEM water electrolyzer device, its mass activity reaches 3563.63 A·g_Ir^-1 at the cell voltage of 2.0 V. This improved catalytic performance is attributed to the following aspects: (1) The electron transport between iridium and tungsten effectively improves the electronic structure of the catalyst; (2) the introduction of iridium into W₁₈O₄₉ by means of elemental bulk doping and nanoparticles supporting for the enhanced conductivity and electrochemically active surface area of the catalyst, resulting in extensive exposure of active sites and increased intrinsic activity; and (3) during the OER process, partial iridium elements in the bulk phase are precipitated, and iridium oxide is formed on the surface to maintain stable activity. This work provides a new idea for designing oxygen evolution catalysts with low iridium content for practical application in PEM electrolyzers.

Enhanced Acidic Water Oxidation by Dynamic Migration of Oxygen Species at the Ir/Nb2 O5-x Catalyst/Support Interfaces

Catalyst/support interaction plays a vital role in catalysis towards acidic oxygen evolution (OER), and the performance reinforcement is currently interpreted by either strain or electron donation effect. We herein report that these views are insufficient, where the dynamic evolution of the interface under potential bias must be considered. Taking Nb₂ O_5-x supported iridium (Ir/Nb₂ O_5-x ) as a model catalyst, we uncovered the dynamic migration of oxygen species between IrO_x and Nb₂ O_5-x during OER. Direct spectroscopic evidence combined with theoretical computation suggests these migrations not only regulate the in situ Ir structure towards boosted activity, but also suppress its over-oxidation via spontaneously delivering excessive oxygen from IrO_x to Nb₂ O_5-x . The optimized Ir/Nb₂ O_5-x thus demonstrated exceptional performance in scalable water electrolyzers, i.e., only need 1.839 V to attain 3 A cm^-2 (surpassing the DOE 2025 target), and no activity decay during a 2000 h test at 2 A cm^-2 .

Iridium Stabilizes Ceramic Titanium Oxynitride Support for Oxygen Evolution Reaction

Decreasing iridium loading in the electrocatalyst presents a crucial challenge in the implementation of proton exchange membrane (PEM) electrolyzers. In this respect, fine dispersion of Ir on electrically conductive ceramic supports is a promising strategy. However, the supporting material needs to meet the demanding requirements such as structural stability and electrical conductivity under harsh oxygen evolution reaction (OER) conditions. Herein, nanotubular titanium oxynitride (TiON) is studied as a support for iridium nanoparticles. Atomically resolved structural and compositional transformations of TiON during OER were followed using a task-specific advanced characterization platform. This combined the electrochemical treatment under floating electrode configuration and identical location transmission electron microscopy (IL-TEM) analysis of an in-house-prepared Ir-TiON TEM grid. Exhaustive characterization, supported by density functional theory (DFT) calculations, demonstrates and confirms that both the Ir nanoparticles and single atoms induce a stabilizing effect on the ceramic support via marked suppression of the oxidation tendency of TiON under OER conditions.

Carbon nanotube-titanium dioxide nanocomposite support for improved activity and stability of an iridium catalyst toward the oxygen evolution reaction

In order to improve the electrocatalytic activity and stability of an iridium (Ir) nanoparticle catalyst toward the oxygen evolution reaction (OER) in acidic electrolyte, carbon nanotube and titanium dioxide nanocomposites (CNT@TiO₂) are presented as a high-performance support. TiO₂ was synthesized on CNTs by using a novel layer-by-layer solution coating method that mimics atomic layer deposition (ALD) but is cost-effective and scalable. In the nanocomposites, CNTs serve as the electron pathways and the surface TiO₂ layers protect CNTs from corrosion under the harsh OER conditions. Thus, CNT@TiO₂ demonstrates excellent corrosion resistance as well as a high electrical conductivity (1.6 ± 0.2 S cm^-1) comparable to that of Vulcan carbon (1.4 S cm^-1). The interaction between Ir and TiO₂ promotes the formation of Ir(iii) species, thereby enhancing the OER activity and stability of the Ir nanoparticle catalyst. Compared to commercial carbon-supported Ir (Ir/C) and Ir black catalysts, CNT@TiO₂-supported Ir exhibits superior OER activity and stability.

IrO2-Stablized La2IrO6 perovskite nanotubes via corner-shared interconnections as highly-efficient oxygen evolution electrocatalysts

One-dimensional nanotube heterostructures with IrO₂-stabilized La₂IrO₆ is obtained by an electrospinning approach. The La₂IrO₆/IrO₂ catalyst exhibits superior catalytic activity and strong stability for the oxygen evolution reaction. The synergistic cooperation between the two types of Ir as the active sites in La₂IrO₆/IrO₂ is demonstrated by in situ Raman spectrum and DFT calculation.

Supported Iridium-based Oxygen Evolution Reaction Electrocatalysts - Recent Developments

The commercialization of acidic proton exchange membrane water electrolyzers (PEMWE) is heavily hindered by the price and scarcity of oxygen evolution reaction (OER) catalyst, i. e. iridium and its oxides. One of the solutions to enhance the utilization of this precious metal is to use a support to distribute well dispersed Ir nanoparticles. In addition, adequately chosen support can also impact the activity and stability of the catalyst. However, not many materials can sustain the oxidative and acidic conditions of OER in PEMWE. Hereby, we critically and extensively review the different materials proposed as possible supports for OER in acidic media and the effect they have on iridium performances.

Metallic Inverse Opal Frameworks as Catalyst Supports for High-Performance Water Electrooxidation

High intrinsic activity of oxygen evolution reaction (OER) catalysts is often limited by their low electrical conductivity. To address this, we introduce copper inverse opal (IO) frameworks offering a well-developed network of interconnected pores as highly conductive high-surface-area supports for thin catalytic coatings, for example, the extremely active but poorly conducting nickel-iron layered double hydroxides (NiFe LDH). Such composites exhibit significantly higher OER activity in 1 m KOH than NiFe LDH supported on a flat substrate or deposited as inverse opals. The NiFe LDH/Cu IO catalyst enables oxygen evolution rates of 100 mA cm^-2 (727±4 A g_catalyst ^-1 ) at an overpotential of 0.305±0.003 V with a Tafel slope of 0.044±0.002 V dec^-1 . This high performance is achieved with 2.2±0.4 μm catalyst layers, suggesting compatibility of the inverse-opal-supported catalysts with membrane electrolyzers, in contrast to similarly performing 10³ -fold thicker electrodes based on foams and other substrates.

2D MXene Nanomaterials as Electrocatalysts for Hydrogen Evolution Reaction (HER): A Review

MXenes, a novel family of 2D transition metal carbide, nitride and carbonitride materials, have been gaining tremendous interest in recent days as potential electrocatalysts for various electrochemical reactions, including hydrogen evolution reaction (HER). MXenes are characterized by their etchable metal layers, excellent structural stability, versatility for heteroatoms doping, excellent electronic conductivity, unique surface functional groups and admirable surface area, suitable for the role of electrocatalyst/support in electrochemical reactions, such as HER. In this review article, we summarized recent developments in MXene-based electrocatalysts synthesis and HER performance in terms of the theoretical and experimental point of view. We systematically evaluated the superiority of the MXene-based catalysts over traditional Pt/C catalysts in terms of HER kinetics, Tafel slope, overpotential and stability, both in acidic and alkaline electrolytic environments. We also pointed out the motives behind the electro catalytic enhancements, the effect of synthesis conditions, heteroatom doping, the effect of surface terminations on the electrocatalytic active sites of various MXenes families. At the end, various possible approaches were recommended for a deeper understanding of the active sites and catalytic improvement of MXenes catalysts for HER.

Tensile-Strained RuO2 Loaded on Antimony-Tin Oxide by Fast Quenching for Proton-Exchange Membrane Water Electrolyzer

Future energy demands for green hydrogen have fueled intensive research on proton-exchange membrane water electrolyzers (PEMWE). However, the sluggish oxygen evolution reaction (OER) and highly corrosive environment on the anode side narrow the catalysts to be expensive Ir-based materials. It is very challenging to develop cheap and effective OER catalysts. Herein, Co-hexamethylenetetramine metal-organic framework (Co-HMT) as the precursor and a fast-quenching method is employed to synthesize RuO₂ nanorods loaded on antimony-tin oxide (ATO). Physical characterizations and theoretical calculations indicate that the ATO can increase the electrochemical surface areas of the catalysts, while the tensile strains incorporated by quenching can alter the electronic state of RuO₂ . The optimized catalyst exhibits a small overpotential of 198 mV at 10 mA cm^-2 for OER, and keeps almost unchanged after 150 h chronopotentiometry. When applied in a real PEMWE assembly, only 1.51 V is needed for the catalyst to reach a current density of 1 A cm^-2 .

Recent Advances Regarding Precious Metal-Based Electrocatalysts for Acidic Water Splitting

Electrochemical water splitting has wide applicability in preparing high-density green energy. The Proton exchange membrane (PEM) water electrolysis system is a promising technique for the generation of hydrogen due to its high electrolytic efficiency, safety and reliability, compactness, and quick response to renewable energy sources. However, the instability of catalysts for electrochemical water splitting under operating conditions limits their practical applications. Until now, only precious metal-based materials have met the requirements for rigorous long-term stability and high catalytic activity under acid conditions. In this review, the recent progress made in this regard is presented and analyzed to clarify the role of precious metals in the promotion of the electrolytic decomposition of water. Reducing precious metal loading, enhancing catalytic activity, and improving catalytic lifetime are crucial directions for developing a new generation of PEM water electrolysis catalysts. A summary of the synthesis of high-performance catalysts based on precious metals and an analysis of the factors affecting catalytic performance were derived from a recent investigation. Finally, we present the remaining challenges and future perspectives as guidelines for practical use.