Microwave-Assisted Rapid Photocatalytic Degradation of Malachite Green in TiO2 Suspensions: Mechanism and Pathways

Inhibit or promote? Trade-off effect of dissolved organic matter on the laccase-mediator system

A biocatalytic system comprising fungal laccase and mediators can generate phenol radicals and efficiently eliminate various triarylmethane dyes. This study systematically explores the kinetic impact of dissolved organic matter (DOM), represented by humic substance (HS consisting of 90% fulvic acid, from lignite), on the decolorization of seven typical triarylmethane dyes by Trametes versicolor laccase and twenty natural mediators. Among these, 4-hydroxybenzyl alcohol (4-HA) and methyl violet (MV) undergo in-depth investigation regarding degradation products, pathways, and reaction mechanisms. In instances where HS hampers laccase-alone decolorization, such as malachite green, Coomassie brilliant blue, bromophenol blue, and acid magenta, this inhibition may persist despite mediator introduction. Conversely, in cases where HS facilitates decolorization, such as crystalline violet and ethyl violet, most laccase-mediator systems (LMSs) can still benefit. For MV decolorization by laccase and 4-HA, HS's kinetic effect is controlled by concentration and reaction time. A 5 mg/L HS increased the decolorization rate from 50% to 67% within the first hour, whereas 10 mg/L HS only achieved 45%. After 16 h of reaction, HS's impact on decolorization rate diminishes. Furthermore, the addition of HS enhances precipitation production, probably due to its involvement in polymerization with MV and mediator. Computational simulations and spectral monitoring reveal that low HS concentrations accelerate laccase-mediated demethylation by disrupting the chromophores bound to MV, thus promoting the decolorization of MV. Conversely, inhibition by high HS concentrations stems from the competitive binding of the enzyme pocket to the mediator, and the reduction of phenol free radicals in the system. Molecular docking and kinetic simulations revealed that laccase forms complexes with both the mediator and MV. Interestingly, the decolorization of MV occurred through a non-radical mechanism in the presence of HS. This work provided a reference for screening of high catalytic performance mediators to remove triarylmethane dyes in the actual water environment.

Removal of malachite green from water: Comparison of adsorption in a residue-derived AC versus photocatalytic oxidation with TiO2 and study of the adsorption-photocatalysis synergy

The literature rarely compiles studies devoted to the removal of pollutants in aqueous media comparing adsorption and photocatalytic degradation, and does not pay enough attention to the analysis of combined adsorption-photocatalytic oxidation processes. In the present manuscript, the removal of malachite green (MG) from aqueous solutions has been investigated in three different sustainable scenarios: i) adsorption on activated carbon (AC) derived from a residue, luffa cylindrica, ii) photocatalytic oxidation under simulated solar light using titanium dioxide (TP) and iii) combined adsorption-photocatalytic oxidation using TP-AC (70/30 wt./wt.) under simulated solar light. The study has revealed that in the three scenarios and studied conditions, the total removal of this endocrine-disrupting dye from the solution takes place in the assayed time, 2 h, in some cases just in a few minutes. MG adsorption in the AC is a very fast and efficient removal method. MG photocatalytic oxidation with TP also occurs efficiently, although the oxidized MG is not totally mineralized. MG removal using the TP-AC composite under simulated solar light occurs only slightly faster to the MG adsorption in the AC, being adsorption the dominating MG removal mechanism for TP-AC. Thus, more than 90% of the removed MG with TP-AC under simulated solar light is adsorbed in this carbon-containing composite. The obtained results highlight the interest in adsorption, being the selection of the most suitable removal method dependent on several factors (i.e., the cost of the AC regeneration, for adsorption, or the toxicity of the intermediate oxidation species, for photooxidation). Paying attention to MG photooxidation with TiO2, comparison of two working photodegradation schemes shows that the direct photodegradation of MG from solution, avoiding any initial dark equilibrium period, is more efficient from a time perspective. The use of scavengers has proved that MG photodegradation occurs via an oxidation mechanism dominated by superoxide anion radicals.

DyMnO3: Synthesis, Characterization and Evaluation of Its Photocatalytic Activity in the Visible Spectrum

DyMnO3 is a p-type semiconductor oxide with two crystal systems, orthorhombic and hexagonal. This material highlights its ferroelectric and ferromagnetic properties, which have been the subject of numerous studies. Nevertheless, its photocatalytic activity has been less explored. In this work, the photocatalytic activity of DyMnO3 is evaluated through the photodegradation of MG dye. For the synthesis of this oxide, a novel and effective method was used: polymer-decomposition. The synthesized powders contain an orthorhombic phase, with a range of absorbances from 300 to 500 nm and a band gap energy of 2.4 eV. It is also highlighted that, when using this synthesis method, some of the main diffraction lines related to the orthorhombic phase appear at 100 °C. Regarding its photocatalytic activity, it was evaluated under visible light (λ = 405 nm), reaching a photodegradation of approximately 88% in a period of 30 min. Photocurrent tests reveal a charge carrier separation (e-,h+) at a 405 nm wavelength. The main reactive oxygen species (ROS) involved in the photodegradation process were radicals, OH•, and photo-holes (h+). These results stand out because it is the first time that the photodegradation capability of this oxide in the visible spectrum has been evaluated.

Magnetic recyclable heterogeneous catalyst Fe3O4/g-C3N4 for tetracycline hydrochloride degradation via photo-Fenton process under visible light

Antibiotic pollution of water resources is a global problem, and the development of new treatments for destroying antibiotics in water is a priority research. We successfully manufactured recyclable magnetic Fe₃O₄/g-C₃N₄ through the electrostatic self-assembly method. Selecting tetracycline (TC) as the target pollutant, using Fe₃O₄/g-C₃N₄ and H₂O₂ developed a heterogeneous optical Fenton system to remove TC under visible light. Fe₃O₄/g-C₃N₄ was systematically characterized by SEM, TEM, XRD, FTIR, XPS, DRS, and electrochemical methods. The removal efficiency of 7% Fe₃O₄/g-C₃N₄ at pH = 3, H₂O₂ = 5 mM, and catalyst dosage of 1.0 g/L can reach 99.8%. After magnetic separation, the Fe₃O₄/g-C₃N₄ photocatalyst can be recycled five times with minimal efficiency loss. The excellent degradation performance of the prepared catalyst may be attributed to the proper coupling interface between Fe₃O₄ and g-C₃N₄ which promotes the separation and transfer of photogenerated electrons. Photogenerated electrons can also accelerate the conversion of Fe³⁺ to Fe²⁺, thereby producing more ˙OH. The new Fe₃O₄/g-C₃N₄ can be used as a raw material for advanced oxidation of water contaminated by refractory antibiotics.

An Integrated Study on the Fading Mechanism of Malachite Green Industrial Dye for the Marquisette Curtain in the Studio of Cleansing Fragrance, the Palace Museum (Beijing)

Historical marquisette curtains were composed of lightweight fabrics, woven in an open-mesh and leno-type weave, usually made of silk, and found in Qing imperial buildings. As panel curtains, they were exposed to light, and so underwent fading. This study investigated the manufacturing technology and fading mechanism of dyed marquisette fabric from the Studio of Cleansing Fragrance, the Palace Museum (Beijing). The technological aspects were identified. The types of weave, fiber, and adhesive used to fix the curtain to the wooden frame were identified through microscopic observation and infrared spectroscopy. A color change characterization was performed based on UV-visible diffuse reflectance spectra. The textile colorant was identified as malachite green (MG), and its degradation by light was subsequently studied by dynamic photolysis experiments in a kinetic solution for the rapid exploration of by-products. The main degradation pathways were thus identified and the factors responsible for the induced color changes were discussed. A comparison of the liquid chromatography-mass spectrometry (LC–MS) results of the products derived from the photolysis method as well as of the samples extracted from the object allowed for the identification of the presence of different degradation pathways in the faded and unfaded parts of the textile. A metabolomics analysis was applied to account for the differences in the degradation pathways.

Atomic sheets of silver ferrite with universal microwave catalytic behavior

Prompt degradation of organic pollutants renders microwave (MW) catalysis technology extremely lucrative; ideal microwave catalysts are therefore being hunted with an unprecedented urgency. Ideal functional microwave catalyst should be highly crystalline, room temperature ferromagnetic (for magnetic retrieval), highly dielectric (for sufficient microwave absorption) apart from being structurally stable at high temperature. The potential of silver ferrite 2D sheets (2D AFO) synthesized using a novel microwave technique as a microwave catalyst for the degradation of a variety of organic dyes and antibiotics was investigated in this article. While organic dyes like malachite green (MG), brilliant green (BG) and nile blue A (NB) achieved 99.2%, 98.8% and 95.2%, respectively; antibiotic tetracycline hydrochloride (TCH) molecule resulted in 75.8% degradation efficiency. Total organic carbon (TOC) measurements yielded 76%, 59.1%, 49.1% and 47.6% of carbon content for MG, BG, NB and TCH, respectively. The reaction pathway via intermediates and subsequent degradation to CO₂ and H₂O is revealed by liquid chromatography-mass spectrometry (LCMS). Both superoxide and hydroxyl radicals are participating in the process, according to scavenger tests. The evolution of silver ferrite as a new 2D material and its demonstration as an ideal microwave catalyst will lead to a new beginning in catalysis science and technology.

Microwave synthesized strontium hexaferrite 2D sheets as versatile and efficient microwave catalysts for degradation of organic dyes and antibiotics

Microwave catalysis is extremely lucrative due to prompt mineralization and superior efficiency. Ideal microwave catalysts should possess crystalline nature, large surface area, room temperature ferromagnetic, high dielectric properties apart from structural stability at elevated temperature. In the present article, the candidature of microwave synthesized strontium hexaferrite 2D sheets (2D SFO) has been explored as microwave catalysts for the degradation of a host of organic dyes and antibiotics. Malachite green (MG) and nile blue A (NB) in particular exhibited 99.8% and 97.6% degradation, respectively. Degradation reaction is established to follow pseudo-second-order kinetics. Total organic carbon (TOC) measurements hint at 52% and 60% mineralization for MG and NB, respectively. Liquid chromatography-mass spectroscopy (LCMS) measurements indicate the reaction pathways via intermediates and eventual mineralization to CO₂ and H₂O. Mott-Schottky measurements along with scavenger tests hint that both hydroxyl and superoxide radicals participate in the reaction. Having superior efficiency apart from the versatile nature of the 2D SFO microwave catalyst, the present research will guide to the emergence of microwave catalysis as a new technology.

Fe3+-citric acid/sodium alginate hydrogel: A photo-responsive platform for rapid water purification

As water pollution in human society becomes more and more serious, the demand for materials that can be used for wastewater treatment is increasing. Here, we reported a sodium alginate-based hydrogel (Fe³⁺-CA/SA hydrogel) that can efficiently photocatalyze the degradation of malachite green. The Fe³⁺-CA/SA hydrogel is composed of sodium alginate, citric acid, and Fe³⁺. The hydrogel has multi-leveled pore structure and photochromic ability. Benefiting from the unique microstructure and positive feedback chemical reaction process, the hydrogel has high photocatalytic efficiency. Under 365 nm UV light irradiation, the hydrogel can degrade around 95% of malachite green (20 mg/L) in about 4 min, and there is no need to add H₂O₂ in the degradation process. The work helps to expand the application of sodium alginate-based hydrogels in the field of water treatment. It also has exploratory significance for the principle of photocatalytic degradation of malachite green.

A high-efficiency mediator-free Z-scheme Bi2MoO6/AgI heterojunction with enhanced photocatalytic performance

A high-efficiency Z-scheme Bi₂MoO₆/AgI heterojunction was designed and fabricated via in situ growth of AgI on Bi₂MoO₆. Its photocatalytic activity was investigated with the degradation of malachite green (MG). After 40 min of visible light irradiation, near complete degradation of MG (20 mg/L) occurred when BA11 (Bi₂MoO₆:AgI = 1:1, 2.0 g/L) was present, while only 29.0% and 49.7% of the MG could be degraded in the presence of Bi₂MoO₆ and AgI, respectively. The excellent photocatalytic activity of BA11 results from strong visible light absorption and the low recombination efficiency of photogenerated electron-hole pairs induced by the formation of heterojunction. Density function theory (DFT) calculations revealed that the formation of built-in electric field at the interface between Bi₂MoO₆ and AgI facilitates the effective separation and transfer of photogenerated charge carriers. Results of reuse experiments indicated that the heterostructured photocatalyst has excellent stability. Radical scavenging experiments and electron spin resonance spectra showed that superoxide radicals (O₂^-) and hydroxyl radicals (OH) were the major reactive oxygen species in the photocatalytic system. The photocatalytic degradation pathway of MG was proposed based on the organic degradation intermediates detected. These findings demonstrate that the mediator-free Z-scheme Bi₂MoO₆/AgI heterojunction could serve as a promising photocatalyst in photocatalytic treatment of organic pollutants.

Detection of Malachite Green in Water Using Edge Excited Label Free Fluorescent Probe NCQDs

The fluorescent properties of nitrogen doped carbon quantum dots (NCQDs) prepared through microwave assisted green method has been used as label free fluorescent probe for selective and sensitive detection of malachite green (MG) in water. The optical responses revealed that the NCQDs are highly stable and have good fluorescent quantum yield. The NCQDs were used to detect the Malchite Green in Mili Q water. Reduction in the fluorescence response was monitored in the range 17.12-128.43 μM of MG dissolved in Mili Q water. Linear response was observed in the range, 10-80 μM. The calculated value of limit of detection is 5.16 μM and the sensitivity is (0.03536 ± 0.00001) μM^-1. The future application of this work is that it can be employed to detect MG in the tap water and other natural sources of water.

Synthesis and characterization of L-asparagine stabilised gold nanoparticles: Catalyst for degradation of organic dyes

L-asparagine functionalized gold nanoparticles (Asp-AuNPs), have been synthesized by reducing HAuCl₄ in presence of L-asparagine at 70 °C for 8 h. Asp-AuNPs were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS); the nanoparticles formed were spherical in shape with average size of 13.5 ± 3.7 nm. Synthesized Asp-AuNPs were found to exhibit excellent catalytic properties for the degradation of different organic dyes viz. Rhodamine B (RB), methyl orange (MO), acid red 27 (amaranth) and xylenol orange (XO) in the presence of sodium borohydride (NaBH₄). Asp-AuNPs acts as electron relay system and serve as effective catalyst for complete degradation of all the tested dyes. Rate kinetic investigations suggested that catalysed degradation reactions follow pseudo-first order reaction kinetics with rate constant of 0.904 min^-1, 0.314 min^-1, 0.228 min^-1 and 0.1 min^-1 for RB, MO, amaranth and XO respectively.

Isopropanol-assisted synthesis of highly stable MAPbBr3/p-g-C3N4 intergrowth composite photocatalysts and their interfacial charge carrier dynamics

Two phase photocatalysts can be intergrown with each other, resulting in superior photocatalytic properties. Herein, methylamine lead bromide (MAPbBr₃) wrapped/entrapped protonated graphitic carbon nitride (p-g-C₃N₄) intergrowth microcrystals were fabricated by mixing a pervoskite precursor with p-g-C₃N₄ colloidal sol. A highly stable isopropanol (IPA) solvent based photocatalytic system for dye degradation was demonstrated. The composite with an optimal p-g-C₃N₄ mass percentage of 3.3 wt% (denoted as MAPbBr₃/p-g-C₃N₄-1.0 mg) exhibited the highest photocatalytic degradation of malachite green (99.8%) within 10 min under visible light, which was 5.3-fold and 16-fold greater than that exhibited by its constituents separately. The strong chemical interaction and fundamental photophysical processes in MAPbBr₃/p-g-C₃N₄ were systematically evaluated by spectroscopic and electrochemical techniques, confirming the effective separation of photogenerated electron-hole pairs and faster interfacial charge transfer behavior. Furthermore, active superoxide radicals (O₂˙^-) played a vital role in the catalytic reaction, because of the significant photoinduced electron transfer rate (k _et) in the inverted type-I core/shell MAPbBr₃/p-g-C₃N₄ band configuration structure. In addition, MAPbBr₃/p-g-C₃N₄ has good cycling stability for 10 cycles and versatility for other cationic (RhB) and anionic (MO) dye pollutants, indicating the great potential for solar energy conversion into chemical energy.

Fe-Based Metallic Glasses and Dyes in Fenton-Like Processes: Understanding Their Intrinsic Correlation

Fe-based metallic glasses have been demonstrated as effective heterogeneous catalysts in Fenton-like processes for dye degradation. Yet, currently corresponding studies have limitations due to the limited study object (dyes) and the correlation between metallic glasses and dye pollutants in Fenton-like processes is still not comprehensively studied. Accordingly, this work intensively investigated the thermal catalytic behavior correlations between two Fe-based metallic glasses (Fe78Si9B13 and Fe73.5Si13.5B9Cu1Nb3) and eight different dyes. Results indicated a lower activation energy in the more active metallic glass and a dependence of the activation energy of Fe-based metallic glasses in dye solutions. In addition, a high H2O2 concentration led to a declined catalytic efficiency but a photo-enhanced Fenton-like process overcame this limitation at high concentration of H2O2 due to the decrease of pH and enhancement of irradiation. Furthermore, the average mineralization rates of Fe78Si9B13 and Fe73.5Si13.5B9Cu1Nb3 have been measured to be 42.7% and 12.6%, respectively, and the correlation between decolorization and mineralization revealed that a faster decolorization in a Fenton-like process contributed to a higher mineralization rate. This work provides an intrinsic viewpoint of the correlation between Fe-based metallic glasses and dyes in Fenton-like processes and holds the promise to further promote the industrial value of metallic glasses.

Microwave-Assisted Catalytic Degradation of Brilliant Green by Spinel Zinc Ferrite Sheets

Microwave (MW)-assisted catalytic degradation, being an emerging technique, can potentially fill in the technological gap which promises on-demand, prompt, and efficient catalysis, and therefore, suitable MW catalysts are curiously being hunted. Candidature of spinel zinc ferrite (SZFO) atomic sheets as a MW catalyst has thoroughly been investigated in this article. Analytical techniques prove SZFO atomic sheets to be highly crystalline, thermally stable, good dielectric, and superparamagnetic, which render it a potentially strong MW catalyst. Brilliant green (BG) has been demonstrated to be chemisorbed on the SZFO atomic sheets, which upon MW irradiation gets mineralized within 5 min, and the overall efficiency has been observed to be >99%. Total organic carbon removal of ∼80% has been obtained. Ionic chromatography proves the formation of SO₄ ^2- and NO₃ ^- anions which increase with MW exposure time. Liquid chromatography mass spectroscopy studies have established intermediate formations during catalysis. SZFO, established as a uniquely suited and highly efficient MW catalyst for BG, is expected to broaden the horizons of MW-assisted catalytic degradation and lead it toward its broader applications.

Acetylacetone extends the working life of laccase in enzymatic transformation of malachite green by interfering with a key intermediate

The potential of acetylacetone (AA) as a mediator of laccase has been tested in the enzymatic transformation of malachite green (MG). AA inhibited the laccase-induced transformation of MG at the beginning of incubation but extended the working life of laccase in long runs. To elucidate the underlying mechanisms, the transformation of MG in the laccase-AA system was systematically investigated. The inhibition of AA on the enzymatic transformation of MG conformed to the partial mixed model. The transformation of N,N,N',N'-tetramethyl-1,1'-biphenyl-4,4'-diamine (NTB) was identified as the rate-controlling step in the laccase system. The generated NTB was oxidized to NTB⁺ by laccase, which acted as a redox mediator to accelerate the transformation of MG. The addition of AA to the enzymatic system quenched the NTB⁺ by forming an intermediate complex of AA-NTB. This quenching reaction led to two contrary effects: the acceleration caused by NTB⁺ in the enzymatic transformation of MG was inhibited whereas the formation of AA-NTB complex enhanced the further transformation at the later stage. As a result, less laccase was consumed, which explained the extended working life of laccase in the long runs. The understanding of these mechanisms are helpful for the better use of laccase as a green biocatalyst.

Biodegradation of triphenylmethane dye crystal violet by Cedecea davisae

The present study focuses on the biodegradation of triphenylmethane dye crystal violet (CV) by Cedecea davisae. The degradation of CV was evaluated via ultraviolet absorbance at 254 nm (UV₂₅₄) and chemical oxygen demand (COD) removal, and the kinetics was used to evaluate the degradation efficiency. Intermediate products were analyzed via UV-vis spectroscopy (UV), Fourier transform infrared spectroscopy (FTIR), and high-performance liquid chromatography (HPLC). Results showed that C. davisae was able to decolorize the CV, and the maximum decolorization ratio reached 97%. COD reduction was observed after decolorization, with average removal rates of >90% after 48 h. Moreover, 50% of UV₂₅₄ can be removed after 14 h. The removal efficiency of CV by C. davisae followed first- and second-order reaction kinetics at temperature ranged from 20 °C to 40 °C and pH 4.0 to 6.0, respectively. By using UV, the peak representing the CV disappeared 14 h after CV decolorization, and the degradation of aromatic and naphthalene rings was attributed to the formation of a new metabolite. The FTIR spectra of metabolites showed that a new functional group of OH, CH, CH₂, CH₃, NH, CN, CN, or CO was produced. The chromatograms of HPLC recorded at 589 nm at retention time decreased and were not detected following incubation for 8 h by C. davisae.

A comprehensive study on the electrocatalytic degradation, electrochemical behavior and degradation mechanism of malachite green using electrodeposited nanostructured β-PbO2 electrodes

This work has investigated the electrocatalytic degradation of malachite green (MG) in aqueous solution with G/β-PbO₂, SS316/β-PbO₂, Ti/β-PbO₂ and Pb/β-PbO₂ electrodes. These electrodes show high oxygen evolution over-potential and excellent electrochemical degradation efficiency for organic pollutants. The optimum conditions for the degradation of MG were obtained by studying the effects of different parameters, such as initial current densities and initial MG concentration. The remaining organic compounds concentrations (color) and chemical oxygen demand (COD) removal efficiency were investigated and compared. The results indicate that the efficiency of G/β-PbO₂ electrode for both color and COD removals is more than those of other electrodes. At the optimum conditions, the color and COD removal efficiencies of MG reached up to 100% and 94%, respectively. The observed degradation rate of MG was found to vary in the order G/β-PbO₂> SS316/β-PbO₂> Ti/β-PbO₂> Pb/β-PbO₂. Moreover, in this paper, the electrochemical behavior and adsorption characteristic of MG in aqueous solutions with different pH values were studied in details at glassy carbon electrode using both constant-current coulometry and cyclic voltammetry techniques. This study has led to the proposed mechanism for the oxidation pathway of MG and determine the absorption properties of MG in acidic, neutral and basic solutions. We also proposed the mineralization pathway of MG at β-PbO₂ electrode.

Fabrication of Ag-decorated BiOBr-mBiVO4 dual heterojunction composite with enhanced visible light photocatalytic performance for degradation of malachite green

A visible light active Ag-decorated BiVO₄-BiOBr dual heterojunction photocatalyst was prepared using a facile hydrothermal method, followed by the photodeposition of Ag. The photocatalytic activity of the synthesized samples was investigated by monitoring the change in malachite green (MG) concentration upon visible light irradiation. The synthesized sample was highly effective for the degradation of non-biodegradable MG. The enhanced activity observed was ascribed to the efficient separation and transfer of charge carriers across the dual heterojunction structure as verified by photoluminescence measurements. The removal of MG was primarily initiated by hydroxyl radicals and holes based on scavenger's effect. To gain insight into the degradation mechanism, both high performance liquid chromatography and high resolution-quantitative time of flight, electrospray ionization mass spectrometry measurements during the degradation process were carried out. The degradation primarily followed the hydroxylation and N-demethylation process. A possible reaction pathway is proposed on the basis of all the information obtained under various experimental conditions.

Synthesis of novel laccase-biotitania biocatalysts for malachite green decolorization

Biomimetic mineralization has emerged as a novel tool for generating excellent supports for enzyme stabilization. In this work, protamine was used to induce titanium (IV) bis(ammonium lactato) dihydroxide (Ti-BALDH) into titania nanoparticles. This biomimetic titanification process was adopted for laccase immobilization. Laccase-biotitania biocatalyst was prepared and the effect of different parameters (buffer solution, titania precursor concentration, protamine concentration, and enzyme loading) on the encapsulation efficiency and recovery of laccase were evaluated. Compared with free laccase, the thermal and pH stability of immobilized laccase were improved significantly. In addition, laccase loaded on titania was effective at enhancing its storage stability. After seven consecutive cycles, the immobilized laccase still retained 51% of its original activity. Finally, laccase-biotitania biocatalysts showed good performance on decolorization of malachite green (MG), which can be attributed to an adsorption and degradation effect. The intermediates of the MG degradation were identified by gas chromatography-mass spectrometry (GC-MS) analysis, and the most probable degradation pathway was proposed. This study provides deeper understanding of the laccase-biotitania particles as a fast biocatalyst for MG decolorization.

Naked eye and spectrophotometric detection of chromogenic insecticide in aquaculture using amine functionalized gold nanoparticles in the presence of major interferents

Detection of a chromogenic insecticide, malachite green (MG) using 3,5-diamino-1,2,4-triazole capped gold nanoparticles (DAT-AuNPs) by both naked eye and spectrophotometry was described in this paper. The DAT-AuNPs were prepared by wet chemical method and show absorption maximum at 518nm. The zeta potential of DAT-AuNPs was found to be -39.9mV, suggesting that one of the amine groups of DAT adsorbed on the surface of AuNPs and the other amine group stabilizes the AuNPs from aggregation. The wine red color DAT-AuNPs changes to violet while adding 25μM MG whereas the absorption band at 518nm was increased and shifted towards longer wavelength. However, addition of 70μM MG leads to the aggregation of DAT-AuNPs. This is due to strong electrostatic interaction between ammonium ion of MG and the free amine group of DAT. Based on the color change and shift in SPR band, 25 and 5μM MG can be easily detected by naked eye and spectrophotometry. The DAT-AuNPs show high selectivity towards MG even in the presence of 5000-fold higher concentrations of common interferents. The practical application was successfully demonstrated by determining MG in fish farm water.

Degradation and detoxification of the triphenylmethane dye malachite green catalyzed by crude manganese peroxidase from Irpex lacteus F17

Malachite green (MG), a recalcitrant, carcinogenic, and mutagenic triphenylmethane dye, was decolorized and detoxified using crude manganese peroxidase (MnP) prepared from the white rot fungus Irpex lacteus F17. In this study, the key factors (pH, temperature, MG, Mn(2+), H2O2, MnP) in these processes were investigated. Under optimal conditions, 96 % of 200 mg L(-1) of MG was decolorized when 66.32 U L(-1) of MnP was added for 1 h. The K m, V max, and k cat values were 109.9 μmol L(-1), 152.8 μmol L(-1) min(-1), and 44.5 s(-1), respectively. The decolorization of MG by MnP followed first-order reaction kinetics with a kinetic rate constant of 0.0129 h(-1). UV-vis and UPLC analysis revealed degradation of MG. Furthermore, seven different intermediates formed during the MnP treatment of 0.5 h were identified by LC-TOF-MS. These degradation products were generated via two different routes by either N-demethylation of MG or the oxidative cleavage of the C-C double bond in MG. Based on ecotoxicity analyses performed on bacteria and algae, it was confirmed that MG metabolites produced by the MnP-catalyzed system were appreciably less toxic than the parent compound. These studies indicate the potential use of this enzyme system in the clean-up of aquatic and terrestrial environments.

Visible light activated photocatalytic degradation of tetracycline by a magnetically separable composite photocatalyst: Graphene oxide/magnetite/cerium-doped titania

In this study, magnetic graphene oxide-loaded Ce-doped titania (MGO-Ce-TiO2) hybridized composite was prepared by a facile method. The as-prepared samples exhibited good adsorption capacity, high visible-light photoactive and magnetic separability as a novel photocatalyst in the degradation of tetracyclines (TC). The intermediate products and photocatalytic route of TC were proposed based on the analysis results of LC-MS. Moreover, the repeatability of the photoactivity with the use of MGO-Ce-TiO2 was investigated in the multi-round experiments with the assistance of an applied magnetic field. Therefore, the prepared composite photocatalysts were considered as a kind of promising photocatalyst in a suspension reaction system, in which they can offer effectively recovery ability. The effect of MGO content on the photocatalytic performance was also studied, and an optimum content was obtained.

Environmental application of millimetre-scale sponge iron (s-Fe(0)) particles (III): The effect of surface silver

To enhance the dechlorination reactivity of millimetric sponge iron (s-Fe(0)), a facile one-pot method was used to decorate s-Fe(0) with Ag(+) ions under ambient conditions. The results recorded by X-ray diffraction patterns, X-ray photoelectron spectra and high-resolution transmission electron microscopy demonstrated that the growth of Ag(0) was dominated primarily by (111) plane with a mean length of ∼20 nm. The roles of Ag(0) loading, catalyst dosage, particle size, initial pH and contaminant concentration were assessed during the removal of pentachlorophenol (PCP). Catalyst recyclability was also studied. The results revealed that 3-5mm s-Fe(0) particles with 5 wt% Ag(0) loading exhibited the best performance with a dose of 3.0 g per 60 mL PCP solution. In addition, the dechlorination of PCP followed two-step, pseudo-first-order reaction kinetics, and Ag(0)-s-Fe(0) was advantageous compared with bimetals of nanoscale zero-valent iron, iron power and iron flakes. The dechlorination mechanism of PCP over Ag(0)-s-Fe(0) was attributed to the surface Ag(0) decoration, which catalyzed the formation of reactive hydrogen atoms for indirect reaction, and the direct electron transfer via Fe-Ag(0) galvanic cells for direct reaction. This suggests that Ag-based bimetals of s-Fe(0) have great potential in the pretreatment of organic halogen compounds in aqueous solution.

Simultaneous removal of tetracycline hydrochloride and As(III) using poorly-crystalline manganese dioxide

Simultaneous removal of antibiotic tetracycline hydrochloride (TC) and As(III) by poorly-crystalline Mn dioxide was investigated. TC and As(III) can be effectively oxidized and removed by MnO2. High concentrations of TC and As(III) competed with each other for oxidation or adsorption sites on MnO2 and thus affected their removal efficiency. The intermediates and products of TC after reaction with poorly-crystalline manganese dioxide were identified by LC-ESI-MS (liquid chromatography-electrospray ionization-mass spectrometry), and the decomposition pathways of TC by MnO2 were proposed. This study is helpful for understanding the importance of environmental Mn dioxides in the decontamination of combined pollution by organic pollutants and metal(loid)s.

Isotherm and kinetics study of malachite green adsorption onto copper nanowires loaded on activated carbon: artificial neural network modeling and genetic algorithm optimization

In this study, copper nanowires loaded on activated carbon (Cu-NWs-AC) was used as novel efficient adsorbent for the removal of malachite green (MG) from aqueous solution. This new material was synthesized through simple protocol and its surface properties such as surface area, pore volume and functional groups were characterized with different techniques such XRD, BET and FESEM analysis. The relation between removal percentages with variables such as solution pH, adsorbent dosage (0.005, 0.01, 0.015, 0.02 and 0.1g), contact time (1-40min) and initial MG concentration (5, 10, 20, 70 and 100mg/L) was investigated and optimized. A three-layer artificial neural network (ANN) model was utilized to predict the malachite green dye removal (%) by Cu-NWs-AC following conduction of 248 experiments. When the training of the ANN was performed, the parameters of ANN model were as follows: linear transfer function (purelin) at output layer, Levenberg-Marquardt algorithm (LMA), and a tangent sigmoid transfer function (tansig) at the hidden layer with 11 neurons. The minimum mean squared error (MSE) of 0.0017 and coefficient of determination (R(2)) of 0.9658 were found for prediction and modeling of dye removal using testing data set. A good agreement between experimental data and predicted data using the ANN model was obtained. Fitting the experimental data on previously optimized condition confirm the suitability of Langmuir isotherm models for their explanation with maximum adsorption capacity of 434.8mg/g at 25°C. Kinetic studies at various adsorbent mass and initial MG concentration show that the MG maximum removal percentage was achieved within 20min. The adsorption of MG follows the pseudo-second-order with a combination of intraparticle diffusion model.

Environmental application of millimeter-scale sponge iron (s-Fe(0)) particles (II): the effect of surface copper

To enhance the catalytic reactivity of millimeter-scale particles of sponge iron (s-Fe(0)), Cu(2+) ions were deposited on the surface of s-Fe(0) using a simple direct reduction reaction, and the catalytic properties of the bimetallic system was tested for removal of rhodamine B (RhB) from an aqueous solution. The influence of Cu(0) loading, catalyst dosage, particle size, initial RhB concentration, and initial pH were investigated, and the recyclability of the catalyst was also assessed. The results demonstrate that the 3∼5 millimeter s-Fe(0) particles (s-Fe(0)(3∼5mm)) with 5wt% Cu loading gave the best results. The removal of RhB followed two-step, pseudo-first-order reaction kinetics. Cu(0)-s-Fe(0) showed excellent stability after five reuse cycles. Cu(0)-s-Fe(0) possesses great advantages compared to nanoscale zero-valent iron, iron power, and iron flakes as well as its bimetals. The surface Cu(0) apparently catalyzes the production of reactive hydrogen atoms for indirect reaction and generates Fe-Cu galvanic cells that enhance electron transfer for direct reaction. This bimetallic catalyst shows great potential for the pre-treatment of recalcitrant wastewaters. Additionally, some oxides containing iron element are selected to simulate the adsorption process. The results prove that the adsorption process of FeOOH, Fe2O3 and Fe3O4 played minor role for the removal of RhB.

Photodegradation of malachite green under simulated and natural irradiation: kinetics, products, and pathways

In this work photodegradation rates and pathways of malachite green were studied under simulated and solar irradiation with the goal of assessing the potential of photolysis as a removal mechanism in real aquatic environment. Factors influencing the photodegradation process were investigated, including pH, humic acid, Fe(2+), Ca(2+), HCO3(-), and NO3(-), of which favorable conditions were optimized by the orthogonal array design under simulated sunlight irradiation in the presence of dissolved oxygen. The degradation processes of malachite green conformed to pseudo first-order kinetics and their degradation rate constants were between 0.0062 and 0.4012 h(-1). Under solar irradiation, the decolorization efficiency of most tests can reach almost 100%, and relatively thorough mineralization could be observed. Forty degradation products were detected by liquid chromatography-mass spectrometry, and thirteen small molecular products were identified by gas chromatography-mass spectrometry. Based on the analyses of the degradation products and calculation of the frontier electron density, the pathways were proposed: decomposition of conjugated structure, N-demethylation reactions, hydroxyl addition reactions, the removal of benzene ring, and the ring-opening reaction. This study has provided a reference, both for photodegradation of malachite green and future safety applications and predictions of decontamination of related triphenylmethane dyes under real conditions.

Investigation on the interaction between an antimicrobial in aquaculture, malachite green and hemocyanin from mud crab Scylla paramamosain

Interaction between malachite green and hemocyanin of crab plays a crucial role in the metabolism, distribution, and efficacy of toxic dyes in aquaculture. The mechanism of interaction between malachite green and Hc from mud crab was studied by using multi-spectral methods and molecular modeling in this work. The spectroscopic and thermodynamic data show that the interaction is a spontaneous process with the estimated enthalpy and entropy changes of -14.85(±1.86) kJ mol(-1) and 30.38(±5.21) J mol(-1) K(-1), respectively. The binding sites of malachite green in hemocyanin mainly locate in the interface of protein. The hydrophobic and electrostatic forces are the primary contributors to the interaction between hemocyanin and malachite green. The results of ultraviolet-vis absorbance, circular dichroism, and synchronous fluorescence spectroscopy suggest that the binding of malachite green to hemocyanin induces some conformational changes of protein.

Sonochemical degradation of Coomassie Brilliant Blue: effect of frequency, power density, pH and various additives

Coomassie Brilliant Blue (CBB), discharged mainly from textile industries, is an identified water pollutant. Ultrasound initiated degradation of organic pollutants is one among the promising techniques and forms part of the Advanced Oxidation Processes (AOPs). Ultrasonic degradation of CBB under different experimental conditions has been investigated in the present work. The effect of frequency (200 kHz, 350 kHz, 620 kHz and 1 MHz) and power density (3.5 W mL(-1), 9.8 W mL(-1) and 19.6 W mL(-1)) on the degradation profile was evaluated. The optimum performance was obtained at 350 kHz and 19.6 W mL(-1). Similar to other sonolytic degradation of organic pollutants, maximum degradation of CBB was observed under acidic pH. The degradation profile indicated a pseudo-first order kinetics. The addition of ferrous ion (1×10(-4) M), hydrogen peroxide (1×10(-4) M), and peroxodisulphate (1×10(-4) M) had a positive effect on the degradation efficiency. The influence of certain important NOM like SDS and humic acid on the sonolytic degradation of CBB was also investigated. Both the compounds suppress the degradation efficiency. LC-Q-TOF-MS was used to identify the stable intermediate products. Nearly 13 transformed products were identified during 10min of sonication using the optimized operational parameters. This product profile demonstrated that most of the products are formed mainly by the OH radical attack. On the basis of these results, a degradation mechanism is proposed.

Environmental application of millimetre-scale sponge iron (s-Fe⁰) particles (I): pretreatment of cationic triphenylmethane dyes

To investigate the removal capability of millimetric zero valent iron (mmZVI), sponge iron (s-Fe(0)) particles were characterized with XRD, XPS, TEM, HRSEM and EDS techniques. Moreover, the roles of particle size, catalyst dosage, dye concentration, mixing conditions (e.g. ultrasound (US), stirring or shaking), and regeneration treatment were studied with the removal of cationic triphenylmethane dyes. Notably, the reduction process was also revealed as compared to nanoscale zero valent iron (nZVI), microscale iron power, and iron scurf. Furthermore, the reductive mechanism was exemplified with brilliant green. The results demonstrated that (1) the synergetic effect between US and s-Fe(0) greatly enhanced the removal of dyes, (2) the dosage of preferred s-Fe(0) (1-3mm) particles was optimized as 30.0g/L; (3) reuse cycles of s-Fe(0) catalyst were enhanced with the assistance of diluted HCl solution; (4) the main degradation routes included the cleavage of conjugated structure reactions, N-de-ethylation reactions, hydroxylation reactions, the removal of benzene ring reactions, and opening ring reactions. Accordingly, the pretreatment of aqueous solution over s-Fe(0) was hypothesized to achieve mainly through direct reduction reaction by electron transfer and indirect reductive reactions by the highly activated hydrogen atom. Additionally, decoration with noble metals was utilized to reveal the reaction mechanism.

Synthesis and Characterization of Highly Efficient Nickel Nanocatalysts and Their Use in Degradation of Organic Dyes

The present study describes the synthesis of highly active and ordered structures of nickel nanocatalysts by a facile, green, and economically viable approach. The study reveals efficient catalytic activity for the degradation of a number of toxic organic dyes, such as eosin-B (EB), rose bengal (RB), eriochrome black-T (ECBT), and methylene blue (MB). The stable ordered nickel nanostructure (Ni NSs) arrays were prepared via a modified hydrazine reduction route with unique and controlled morphologies in a lyotropic liquid crystalline medium using a nonionic surfactant (Triton X-100). Characterization and optimization studies for the fabricated Ni NSs involving their surface binding interactions, size, and morphologies were carried out using UV-Vis spectroscopy, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and scanning electron microscopy (SEM).

Could microwave induced catalytic oxidation (MICO) process over CoFe2O4 effectively eliminate brilliant green in aqueous solution?

In this study, we adopted the chemical co-precipitation (CP) method and sol-gel method followed by calcination at temperatures of 100-900°C for 12h to synthesize CoFe2O4 materials, which were further characterized by TEM, XRD and XPS techniques. The properties of CoFe2O4 materials were evaluated in a microwave (MW) induced catalytic oxidation (MICO) process for the elimination of brilliant green (BG). The results showed that: (1) the removal rates of BG gradually decreased over a series of CoFe2O4 materials prepared by CP method and calcinated with 100-700°C (except 900°C) for 12h within three reuse cycles; for comparison, no removal of BG was obtained over CoFe2O4 synthesized by sol-gel method and CoFe2O4-900 (CP); (2) no hydroxyl radicals were captured with salicylic acid used as molecular probe in the MICO process; (3) MW irradiation enhanced the release of residual NaOH within the microstructure of CoFe2O4 and further discolored BG, because BG is sensitive to pH; (4) granular activated carbon (GAC), an excellent MW-absorbing material possessing higher dielectric loss tangent compared to that of a series of CoFe2O4 materials, could not remove BG in suspensions at a higher efficiency, even if the loading amount was 20 g L(-1). Accordingly, MICO process over CoFe2O4 materials and GAC could not effectively eliminate BG in suspensions.