Dense monolayers of metal-chelating ligands covalently attached to carbon electrodes electrochemically and their useful application in affinity binding of histidine-tagged proteins

Pathogen-Specific Electrochemical Real-Time LAMP Detection Using Universal Solid-Phase Probes on Carbon Electrodes

Epidemic infections and spreading antibiotic resistance require diagnostic tests that can be rapidly adopted. To reduce the usually time-consuming adaptation of molecular diagnostic tests to changing targets, we propose the novel approach of a repurposable sensing electrode functionalization with a universal, target-independent oligonucleotide probe. In the liquid phase covering the electrode, the target sequence is amplified by MD LAMP (mediator-displacement loop-mediated isothermal amplification) releasing a generic methylene blue-labeled mediator, which specifically hybridizes to the solid-phase probe. To demonstrate the universality of the approach, two different pathogens, Staphylococcus aureus (crude lysate) and Treponema pallidum, are detected using the same solid-phase probe. The reactions reach a limit of detection of 1 × 103 and 4 × 102 copies per reaction within 30 min, respectively. The solid-phase probes carry a carboxymethyl aniline modification to form covalent C-C bonds on low-cost carbon electrodes. Maximum surface coverage and maximum hybridization signals are observed at grafting concentrations of ≥2 μM solid-phase probes. Successful detection of spiked target DNA in real swab samples and with three different commercial amplification buffers proved the broad applicability of this assay approach. The electrochemical MD LAMP is fast, compatible with dsDNA targets, and requires only minimal adaptation of an established amplification method. It is easily transferable to existing analytical electrochemical platforms, allowing the consumable to be synergistically used for different targets. The suggested approach of repurposable functionalized electrodes can also be considered to increase the preparedness for future epidemic or pandemic outbreaks as well as rapidly evolving resistance patterns or variants.

Biosensors Based on the Binding Events of Nitrilotriacetic Acid-Metal Complexes

Molecular immobilization and recognition are two key events for the development of biosensors. The general ways for the immobilization and recognition of biomolecules include covalent coupling reactions and non-covalent interactions of antigen-antibody, aptamer-target, glycan-lectin, avidin-biotin and boronic acid-diol. Tetradentate nitrilotriacetic acid (NTA) is one of the most common commercial ligands for chelating metal ions. The NTA-metal complexes show high and specific affinity toward hexahistidine tags. Such metal complexes have been widely utilized in protein separation and immobilization for diagnostic applications since most of commercialized proteins have been integrated with hexahistidine tags by synthetic or recombinant techniques. This review focused on the development of biosensors with NTA-metal complexes as the binding units, mainly including surface plasmon resonance, electrochemistry, fluorescence, colorimetry, surface-enhanced Raman scattering spectroscopy, chemiluminescence and so on.

Label-free designed nanomaterials enrichment and separation techniques for phosphoproteomics based on mass spectrometry

The surface chemical characteristics of nanomaterials have a substantial impact on the affinity probe used to enrich proteins and peptides for MALDI-MS analysis of a real human sample. Detecting phosphoproteins involved in signalling is always difficult, even with recent developments in mass spectrometry, because protein phosphorylation is often temporary from complicated mixtures. This review summarizes current research on the successful enrichment of various intriguing glycoproteins and glycol peptides using surface affinity materials with distinctive qualities such as low cost, excellent structural stability, diversity, and multifunction. As a consequence, this review will provide a quick overview of the scholars from various backgrounds who are working in this intriguing interdisciplinary field. Label-free cancer biomarkers and other diseases will benefit from future challenges.

Recombinant Histidine-Tagged Nano-protein-based Highly Sensitive Electro-Sensing Device for Salivary Cortisol

We have developed a powerful biosensing strategy for immobilizing histidine-tagged (His-Tag)-oriented recombinant nano-protein immobilization on a chemically modified glassy carbon electrode (GCE) surfaces via (S)-N-(5-amino-1-carboxypentyl)iminodiacetic acid (ANTA) acting as a chelating Ni2+ centered interaction. Here, we introduce a label-free electro-sensor to quantify cortisol levels in saliva samples for point-of-care testing (POCT). The high specificity of the chemically modified GCE was established by genetically bio-engineered metal-binding sites on the selected recombinant apoferritin (R-AFTN) nano-protein to impart functionality to its surface and by coating the carbon surface with the self-assembled monolayers of 4-aminobenzoic acid (4-ABA) attached to ANTA groups complexed with Ni2+ transition metal ions. Despite the variety of conventional assays available to monitor cortisol levels, they require bulky exterior outfits, which hinders use in the healthcare systems. Therefore, we performed a rapid, easy-to-implement, and low-cost quantitative electro-sensor to enable the real-time detection of cortisol levels in saliva samples. As a result, the cortisol electro-sensor fabricated with high specificity utilizing a GCE could measure cortisol levels with a detection limit of 0.95 ng/ml and sensitivity of 7.91 μA/(ng/mL), which is a practical approach in human saliva. Thus, protein nanoprobe-based cortisol biosensing showed high sensitivity and selectivity for the direct electro-sensing of cortisol for POCT.

A Novel Copper-Binding Peptide That Self-Assembles Into a Transparent Antibacterial and Antiviral Coating

The health, economy, and quality of life all over the world are greatly affected by bacterial infections and viral outbreaks. Bacterial cells and viruses, such as influenza, can spread through contaminated surfaces and fomites. Therefore, a possible way to fight these pathogens is to utilize antibacterial and antiviral coatings, which reduce their numbers on contaminated surfaces. Here, we present a novel short peptide that can self-assemble, adhere to various surfaces, and bind different metal ions such as copper, which provides the surface with antibacterial and antiviral properties. For these functions, the peptide incorporates the amino acid 3,4-dihydroxyphenylalanine (DOPA), which provides the peptide with adhesive capabilities; a diphenylalanine motif that induces the self-assembly of the peptide; the metal-binding hexahistidine sequence. Our results demonstrate that the coating, which releases monovalent cuprous ions and hydrogen peroxide, provides the surfaces with significant antibacterial and antiviral properties. Additionally, the coating remains transparent, which is favorable for many objects and especially for display screens.

Building Tailored Interfaces through Covalent Coupling Reactions at Layers Grafted from Aryldiazonium Salts

Aryldiazonium ions are widely used reagents for surface modification. Attractive aspects of their use include wide substrate compatibility (ranging from plastics to carbons to metals and metal oxides), formation of stable covalent bonding to the substrate, simplicity of modification methods that are compatible with organic and aqueous solvents, and the commercial availability of many aniline precursors with a straightforward conversion to the active reagent. Importantly, the strong bonding of the modifying layer to the surface makes the method ideally suited to further on-surface (postfunctionalization) chemistry. After an initial grafting from a suitable aryldiazonium ion to give an anchor layer, a target species can be coupled to the layer, hugely expanding the range of species that can be immobilized. This strategy has been widely employed to prepare materials for numerous applications including chemical sensors, biosensors, catalysis, optoelectronics, composite materials, and energy conversion and storage. In this Review our goal is first to summarize how a target species with a particular functional group may be covalently coupled to an appropriate anchor layer. We then review applications of the resulting materials.

EIS-Based Biosensors in Foodborne Pathogen Detection with a Special Focus on Listeria monocytogenes

In this chapter methods and protocols for surfaces adapted to electrochemical impedance detection, antibody binding, electrolyte couples used, and instrumentation for EIS Biosensing are presented. Various technical bottlenecks have been overcome in recent years. Other limitations still present in this technique are discussed. We present the most recent applications in food pathogen detection based on EIS methods, as well as using other antibody-based platforms.

In Situ Spectroelectrochemical Studies into the Formation and Stability of Robust Diazonium-Derived Interfaces on Gold Electrodes for the Immobilization of an Oxygen-Tolerant Hydrogenase

Surface-enhanced infrared absorption spectroscopy is used in situ to determine the electrochemical stability of organic interfaces deposited onto the surface of nanostructured, thin-film gold electrodes via the electrochemical reduction of diazonium salts. These interfaces are shown to exhibit a wide electrochemical stability window in both acetonitrile and phosphate buffer, far surpassing the stability window of thiol-derived self-assembled monolayers. Using the same in situ technique, the application of radical scavengers during the electrochemical reduction of diazonium salts is shown to moderate interface formation. Consequently, the heterogeneous charge-transfer resistance can be reduced sufficiently to enhance the direct electron transfer between an immobilized redox-active enzyme and the electrode. This was demonstrated for the oxygen-tolerant [NiFe] hydrogenase from the "Knallgas" bacterium Ralstonia eutropha by relating its electrochemical activity for hydrogen oxidation to the interface properties.

Fluorescence-Free Biosensor Methods in Detection of Food Pathogens with a Special Focus on Listeria monocytogenes

Food pathogens contaminate food products that allow their growth on the shelf and also under refrigerated conditions. Therefore, it is of utmost importance to lower the limit of detection (LOD) of the method used and to obtain the results within hours to few days. Biosensor methods exploit the available technologies to individuate and provide an approximate quantification of the bacteria present in a sample. The main bottleneck of these methods depends on the aspecific binding to the surfaces and on a change in sensitivity when bacteria are in a complex food matrix with respect to bacteria in a liquid food sample. In this review, we introduce surface plasmon resonance (SPR), new advancements in SPR techniques, and electrochemical impedance spectroscopy (EIS), as fluorescence-free biosensing technologies for detection of L. monocytogenes in foods. The application of the two methods has facilitated L. monocytogenes detection with LOD of 1 log CFU/mL. Further advancements are envisaged through the combination of biosensor methods with immunoseparation of bacteria from larger volumes, application of lab-on-chip technologies, and EIS sensing methods for multiplex pathogen detection. Validation efforts are being conducted to demonstrate the robustness of detection, reproducibility and variability in multi-site installations.

Diamond nanowires modified with poly[3-(pyrrolyl)carboxylic acid] for the immobilization of histidine-tagged peptides

Coating boron-doped diamond nanowires (BDD NWs) with a conducting polymer, poly[3-(pyrrolyl)carboxylic acid], has been reported. Polymer coating was achieved through electropolymerization of 3-(pyrrolyl)carboxylic acid at the electrode interface by amperometrically biasing the BDD NWs interface until a predefined charge has passed. The poly[3-(pyrrolyl)carboxylic acid] modified BDD NWs (PPA-BDD NWs) were characterized by scanning electron microscopy (SEM) and cyclic voltammetry (CV). Using a deposition charge of 11 mC cm(-2) resulted in a thin polymer film deposition. The availability of the carboxylic groups of the polymer coated BDD NWs electrode was demonstrated through copper ion (Cu(2+)) chelation. The resulting complex was successfully used for the site-specific immobilization of histidine-tagged peptides. The binding process was followed by electrochemical impedance spectroscopy (EIS). The Cu(2+)-chelated PPA-BDD NWs interface showed peptide loading capability comparable to those of commercially available interfaces and can be easily regenerated several times using ethylenediaminetetraacetic acid (EDTA).

Heterogeneous reconstitution of the PQQ-dependent glucose dehydrogenase immobilized on an electrode: a sensitive strategy for PQQ detection down to picomolar levels

A highly sensitive electroanalytical method for determination of PQQ in solution down to subpicomolar concentrations is proposed. It is based on the heterogeneous reconstitution of the PQQ-dependent glucose dehydrogenase (PQQ-GDH) through the specific binding of its pyrroloquinoline quinone (PQQ) cofactor to the apoenzyme anchored on an electrode surface. It is shown from kinetics analysis of both the enzyme catalytic responses and enzyme surface-reconstitution process (achieved by cyclic voltammetry under redox-mediated catalysis) that the selected immobilization strategy (i.e., through an avidin/biotin linkage) is well-suited to immobilize a nearly saturated apoenzyme monolayer on the electrode surface with an almost fully preserved PQQ binding properties and catalytic activity. From measurement of the overall rate constants controlling the steady-state catalytic current responses of the surface-reconstituted PQQ-GDH and determination of the PQQ equilibrium binding (Kb = 2.4 × 10(10) M(-1)) and association rate (kon = 2 × 10(6) M(-1) s(-1)) constants with the immobilized apoenzyme, the analytical performances of the method could be rationally evaluated, and the signal amplification for PQQ detection down to the picomolar levels is well-predicted. These performances outperform by several orders of magnitude the direct electrochemical detection of PQQ in solution and by 1 to 2 orders the detection limits previously achieved by UV-vis spectroscopic detection of the homogeneous PQQ-GDH reconstitution.

Versatile and nondestructive photochemical process for biomolecule immobilization

Covalent immobilization of unmodified biological materials as proteins has been performed through a one-step and soft method. This process is based on a polyazidophenylene layer derived from the electroreduction of the parent salt 4-azidobenzenediazonium tetrafluoborate on gold substrates. The wavelength used (365 nm) for the photochemical grafting of a large variety of molecules as biomolecules is a key point to this nondestructive immobilization method. This simple process is also versatile and could be used for covalently binding a wide range of molecules such as polyethylene glycol moieties, for example. To validate this approach for biochip or microarray fabrication, a surface plasmon resonance imaging (SPRi) platform for immobilization of various antibody families was created by grafting G-protein through this process. This SPRi antibodies platform was tested with several consecutive cycles of antigen injections/regeneration steps without loss of activity.

Trace lead analysis based on carbon-screen-printed-electrodes modified via 4-carboxy-phenyl diazonium salt electroreduction

This paper describes the use of 4-carboxyphenyl-grafted screen-printed carbon electrodes (4-CP-SPEs) for trace lead analysis. These novel and simple use of electrodes were easily prepared by the electrochemical reduction of the corresponding diazonium salt. Pb detection was then performed by a three-steps method in order to avoid oxygen interference: (i) immersion of the grafted screen-printed electrode (SPE) in the sample and adsorption of Pb(II), (ii) reduction of adsorbed Pb(II) by chronoamperometry (CA), and (iii) oxidation of Pb by Anodic Square Wave Voltammetry (SWV). The reoxidation response was exploited for lead detection and quantification. In order to optimize the analytical responses, the influence of the adsorption medium pH and the adsorption time were investigated. Moreover, an interference study was carried out with Cu(II), Hg(II), Al(III), Mn(II), Zn(II), Cd(II) and no major interference can be expected to quantify Pb(II). The described method provided a limit of detection and a limit of quantification of 1.2 × 10(-9)M and 4.1 × 10(-9)M, respectively. These performances indicate that the 4-CP-SPE could be considered as an efficient tool for environmental analysis.

Immobilization of histidine-tagged proteins on electrodes

The development of new enzyme immobilization techniques that do not affect catalytic activity or conformation of a protein is an important research task in biotechnology including biosensor applications and heterogeneous reaction systems. One of the most promising approaches for controlled protein immobilization is based on the immobilized metal ion affinity chromatography (IMAC) principle originally developed for protein purification. Here we describe the current status and future perspectives of immobilization of His-tagged proteins on electrode surfaces. Recombinant proteins comprising histidine-tags or histidine rich native proteins have a strong affinity to transition metal ions. For metal ion immobilization at the electrode surface different matrices can be used such as self-assembled monolayers or conductive polymers. This specific technique allows a reversible immobilization of histidine-tagged proteins at electrodes in a defined orientation which is an important prerequisite for efficient electron transfer between the electrode and the biomolecule. Any application requiring immobilized biocatalysts on electrodes can make use of this immobilization approach, making future biosensors and biocatalytic technologies more sensitive, simpler, reusable and less expensive while only requiring mild enzyme modifications.

Development of a metal-chelated plasmonic interface for the linking of His-peptides with a droplet-based surface plasmon resonance read-off scheme

Monolayers of metal complexes were covalently attached to the surface of lamellar SPR interfaces (Ti/Ag/a-Si(0.63)C(0.37)) for binding histidine-tagged peptides with a controlled molecular orientation. The method is based on the activation of surface acid groups with N-hydroxysuccinimide (NHS), followed by an amidation reaction with (S)-N-(5-amino-1-carboxypentyl)iminodiacetic acid (NTA). FTIR and X-ray photoelectron spectroscopy (XPS) were used to characterize each surface modification step. The NTA modified SPR interface effectively chelated Cu(2+) ions. Once loaded with metal ions, the modified SPR interface was able to bind specifically to histidine-tagged peptides. The binding process was followed by surface plasmon resonance (SPR) in a droplet based configuration. The Cu(2+)-NTA modified interface showed protein loading comparable to commercially available NTA chips based on dextran chemistry and can thus be regarded as an interesting alternative. The sensor interface can be reused several times due to the easy regeneration step using ethylenediaminetetraacetic acid (EDTA) treatment.

Organometallic electrodes: modification of electrode surfaces through cathodic reduction of cyclopentadienyldiazonium complexes of cobalt and manganese

Two organometallic complexes having cyclopentadienyldiazonium ligands have been isolated and characterized by spectroscopy, X-ray crystallography, and electrochemistry. Both CoCp(η(5)-C(5)H(4)N(2))(2+) (2(2+)) and Mn(CO)(3)(η(5)-C(5)H(4)N(2))(+) (3(+)) undergo facile cyclopentadienyldiazonium ligand-based one-electron reductions which liberate dinitrogen and result in strong binding of the cyclopentadienyl ligand to a glassy carbon surface, similar to the processes well established for organic aryldiazonium salts. The organometallic-modified electrodes are robust and have a thickness of approximately one monolayer (Γ = (2-4) × 10(-10) mol cm(-2)). Their voltammetric responses are as expected for a cobaltocenium-modified electrode, [CoCp(η(5)-C(5)H(4)-E)](+), where Cp = cyclopentadienyl and E = electrode, and a "cymantrene"-modified electrode Mn(CO)(3)(η(5)-C(5)H(4)-E). The cobaltocenium electrode has two cathodic surface waves. The first (E(1/2) = -1.34 V vs ferrocene) is highly reversible, whereas the second (E(pc) = -2.4 V) is not, consistent with the known behavior of cobaltocenium. The cymantrene-substituted electrode has a partially chemically reversible anodic wave at E(1/2) = 0.96 V, also consistent with the behavior of its Mn(CO)(3)Cp parent. Many of the properties of aryl-modified electrodes, such as "blockage" of the voltammetric responses of test analytes, are also seen for the organometallic-modified electrodes. Surface-based substitution of a carbonyl group by a phosphite ligand, P(OR)(3), R = Ph or Me, was observed when the cymantrene-modified electrode was anodically oxidized in the presence of a phosphite ligand. The successful grafting of organometallic moieties by direct bonding of a cyclopentadienyl ligand to electrode surfaces expands the chemical and electrochemical dimensions of diazonium-based modified electrodes.

Surface plasmon resonance on gold and silver films coated with thin layers of amorphous silicon-carbon alloys

The paper reports on a novel surface plasmon resonance (SPR) substrate architecture based on the coating of a gold (Au) or silver (Ag) substrate with 5 nm thin amorphous silicon-carbon alloy films. Ag/a-Si(1-x)C(x):H and Au/a-Si(1-x)C(x):H multilayers are found to provide a significant advantage in terms of sensitivity over both Ag and Au for SPR refractive index sensing. The possibility for the subsequent linking of stable organic monolayers through Si-C bonds is demonstrated. In a proof-of-principle experiment that this structure can be used for real-time biosensing experiments, amine terminated biotin was covalently linked to the acid-terminated SPR surface and the specific streptavidin-biotin interaction recorded.

Drug-eluting stent with improved durability and controllability properties, obtained via electrocoated adhesive promotion layer

Drug-eluting stents (DES) have become an accepted technology in intravascular intervention. Manufacturing methodologies of DES are based mainly on mechanical processes, which tend to generate coatings that have poor stability properties; these were recently related as a potential hazard. A novel approach for significantly increasing the adhesion of polymer coatings onto DES is presented. The method is based on the electrochemistry of diazonium salts. These substances are organic compounds with the characteristic structure of R-N(2) (+) X(-), where R is an organic residue and X(-) is an anion. The objective of this article is to study the properties of a selected diazonium salt 4-(1-dodecyloxy)-phenyldiazonium tetrafluoroborate, referred as C(12)-phenyldiazonium. This material was found to be a superior adhesive promoter for polymeric coatings applied onto metallic stents. C(12)-phenyldiazonium was synthesized and electrocoated on metallic stents and plates. The multilayer films of C(12)-phenyldiazonium were further characterized through electrochemical (cyclic voltammetry, impedance spectroscopy), physical (light and scanning electron microscopy, X-ray photoelectron spectroscopy, peeling tests), and chemical methodology (high pressure liquid chromatography). Further biocompatibility properties of the electrocoated basecoat were evaluated using in vitro and in vivo models. Synthesized C(12)-phenyldiazonium was successfully electrocoated onto metallic surfaces. Electrochemical tests demonstrated its efficient and controllable electrocoating. C(12)-phenyldiazonium was found to increase polymeric coating stability as was reflected by a standard adhesion test. Electrocoated metallic stents spray-coated with a second polymeric film showed improved durability following incubation in physiological buffer. Furthermore, this improvement in durability exhibits stabilized drug release. In addition, biocompatibility evaluations have demonstrated basecoat's inert properties.