Effect of high salt concentrations on the stabilization of bubbles by silica particles

Recent advances in nanomaterial-stabilized pickering foam: Mechanism, classification, properties, and applications

Pickering foam is a type of foam stabilized by solid particles known as Pickering stabilizers. These solid stabilizers adsorb at the liquid-gas interface, providing superior stability to the foam. Because of its high stability, controllability, versatility, and minimal environmental impact, nanomaterial-stabilized Pickering foam has opened up new possibilities and development prospects for foam applications. This review provides an overview of the current state of development of Pickering foam stabilized by a wide range of nanomaterials, including cellulose nanomaterials, chitin nanomaterials, silica nanoparticles, protein nanoparticles, clay mineral, carbon nanotubes, calcium carbonate nanoparticles, MXene, and graphene oxide nanosheets. Particularly, the preparation and surface modification methods of various nanoparticles, the fundamental properties of nanomaterial-stabilized Pickering foam, and the synergistic effects between nanoparticles and surfactants, functional polymers, and other additives are systematically introduced. In addition, the latest progress in the application of nanomaterial-stabilized Pickering foam in the oil industry, food industry, porous functional material, and foam flotation field is highlighted. Finally, the future prospects of nanomaterial-stabilized Pickering foam in different fields, along with directions for further research and development directions, are outlined.

Analysis of stability of silica nano-particle-laden microbubble dispersion

Microbubbles are small gas-filled bubbles which have wide application in various industries. The stability of microbubble is of primary concern for the application of microbubble. In this research, the stability of microbubble dispersion generated using CTAB surfactant is analyzed by drainage mechanism. The stability of microbubble dispersion is studied on the basis of the half-life of microbubble dispersion. Microbubble dispersion gas fraction and apparent rise velocity of interface of microbubble dispersion are also calculated. The size of microbubble is estimated from the apparent rise velocity of interface of microbubble dispersion. Further, silica nano-particles are added to the surfactants to study their effect on the stability of microbubble dispersion. The observed results clearly indicate that the stability of microbubble dispersion is significantly affected by the surfactant concentration and the weight of silica nano-particle in the liquid. Similar results were observed for the apparent rise velocity of interface and bubble size of dispersion. The present work may be beneficial for the application of microbubble in various chemical and biochemical industries and scientific community.

Synthesis and stability of switchable CO2-responsive foaming coupled with nanoparticles

CO₂-responsive foaming has been drawing huge attention due to its unique switching characteristics in academic research and industrial practices, whereas its stability remains questionable for further applications. In this paper, a new CO₂-switchable foam was synthesized by adding the preferably selected hydrophilic nanoparticle N20 into the foaming agent C₁₂A, through a series of analytical experiments. Overall, the synergy between cationic surfactants and nanoparticles with a contact angle of 37.83° is the best. More specifically, after adding 1.5 wt% N20, the half-life of foam is 14 times longer than that of pure C₁₂A foam. What’s more, the C₁₂A-N20 solution is validated to own distinctive CO₂-N₂ switching features because very slight foaming degradations are observed in terms of the foaming volume and half-life time even after three cycles of CO₂-N₂ injections. This study is of paramount importance pertaining to future CO₂ foam research and applications in energy and environmental practices.

•

Cationic surfactants have the best synergy with NPs with a contact angle of 37.83°

•

The foam stability increased with the increase of NPs concentration

•

CO₂/N₂ can control the foaming properties of C₁₂A-N20 solution and are reversible

Influence of particle wettability on foam formation in honey

The rising level of obesity is often attributed to high sugar and/or fat consumption. Therefore, the food industry is constantly searching for ways to reduce or eliminate sugar or fat in food products. Therefore, honey foam, which contains little sugar and no fat, can be used as cake, cracker or bread spread instead of butter or margarine which contains a substantial amount of fat or jam that contains a substantial amount of sugar. Small solid particles (nanometers to micrometers) of suitable wettability are now considered outstanding foam-stabilizing agents. However, while the degree of particle wettability necessary to obtain very stable aqueous and nonaqueous foams is well-known, that needed to obtain very stable honey foam is unknown. In this study, the influence of the degree of wettability of fumed silica particles, indicated by their % SiOH (14-100), was investigated in honey in relation to foam formation and foam stability. The honephilic particles (61%-100% SiOH) formed particle dispersion in honey, while foams were obtained with the honephobic particles (14%-50% SiOH). The thread-off between particle dispersion and foam formation occurs at 50% SiOH, meaning foam formation in honey is possible when the particles are at least 50% honephobic. At relatively low particle concentration <1 wt.%, foam volume decreases with increasing honephobicity, but increases with honephobicity at relatively high concentration >1 wt.%. Also, as particle concentration increases, the shape of the air bubbles in the foam changes from spherical to non-spherical. After a little drainage, the foams remain stable to drainage and did not coalesce substantially for more than six months. These findings will guide the formulation of edible Pickering honey foams.

A broad perspective to particle-laden fluid interfaces systems: from chemically homogeneous particles to active colloids

Particles adsorbed to fluid interfaces are ubiquitous in industry, nature or life. The wide range of properties arising from the assembly of particles at fluid interface has stimulated an intense research activity on shed light to the most fundamental physico-chemical aspects of these systems. These include the mechanisms driving the equilibration of the interfacial layers, trapping energy, specific inter-particle interactions and the response of the particle-laden interface to mechanical perturbations and flows. The understanding of the physico-chemistry of particle-laden interfaces becomes essential for taking advantage of the particle capacity to stabilize interfaces for the preparation of different dispersed systems (emulsions, foams or colloidosomes) and the fabrication of new reconfigurable interface-dominated devices. This review presents a detailed overview of the physico-chemical aspects that determine the behavior of particles trapped at fluid interfaces. This has been combined with some examples of real and potential applications of these systems in technological and industrial fields. It is expected that this information can provide a general perspective of the topic that can be exploited for researchers and technologist non-specialized in the study of particle-laden interfaces, or for experienced researcher seeking new questions to solve.

Pickering foams and parameters influencing their characteristics

Pickering foams are available in many applications and have been continually gaining interest in the last two decades. Pickering foams are multifaceted, and their characteristics are highly dependent on many factors, such as particle size, charge, hydrophobicity and concentration as well as the charge and concentration of surfactants and salts available in the system. A literature review of these individual studies at first might seem confusing and somewhat contradictory, particularly in multi-component systems with particles and surfactants with different charges in the presence of salts. This paper provides a comprehensive overview of particle-stabilized foams, also known as Pickering foams and froths. Underlying mechanisms of foam stabilization by particles with different morphology, surface chemistry, size and type are reviewed and clarified. This paper also outlines the role of salts and different factors such as pH, temperature and gas type on Pickering foams. Further, we highlight recent developments in Pickering foams in different applications such as food, mining, oil and gas, and wastewater treatment industries, where Pickering foams are abundant. We conclude this overview by presenting important research avenues based on the gaps identified here. The focus of this review is limited to Pickering foams of surfactants with added salts and does not include studies on polymers, proteins, or other macromolecules.

Particle-laden fluid/fluid interfaces: physico-chemical foundations

Particle-laden fluid/fluid interfaces are ubiquitous in academia and industry, which has fostered extensive research efforts trying to disentangle the physico-chemical bases underlying the trapping of particles to fluid/fluid interfaces as well as the properties of the obtained layers. The understanding of such aspects is essential for exploiting the ability of particles on the stabilization of fluid/fluid interface for the fabrication of novel interface-dominated devices, ranging from traditional Pickering emulsions to more advanced reconfigurable devices. This review tries to provide a general perspective of the physico-chemical aspects associated with the stabilization of interfaces by colloidal particles, mainly chemical isotropic spherical colloids. Furthermore, some aspects related to the exploitation of particle-laden fluid/fluid interfaces on the stabilization of emulsions and foams will be also highlighted. It is expected that this review can be used for researchers and technologist as an initial approach to the study of particle-laden fluid layers.

Tuning Nanoparticle Surface Chemistry and Interfacial Properties for Highly Stable Nitrogen-In-Brine Foams

The design of surface chemistries on nanoparticles (NPs) to stabilize gas/brine foams with concentrated electrolytes, especially with divalent ions, has been elusive. Herein, we tune the surface of 20 nm silica NPs by grafting a hydrophilic and a hydrophobic ligand to achieve two seemingly contradictory goals of colloidal stability in brine and high NP adsorption to yield a viscoelastic gas-brine interface. Highly stable nitrogen/water (N₂/brine) foams are formed with CaCl₂ concentrations up to 2% from 25 to 90 °C. The viscoelastic gas-brine interface retards drainage of the lamellae, and the high dilational elasticity arrests coarsening (Ostwald ripening) with no observable change in foam bubble size over 48 h. The ability to design NP-laden viscoelastic interfaces for highly stable foams, even with high divalent ion concentrations, is of fundamental mechanistic interest for a broad range of foam applications and in particular foams for CO₂ sequestration and enhanced oil recovery.

Janus Particles at Fluid Interfaces: Stability and Interfacial Rheology

The use of the Janus motif in colloidal particles, i.e., anisotropic surface properties on opposite faces, has gained significant attention in the bottom-up assembly of novel functional structures, design of active nanomotors, biological sensing and imaging, and polymer blend compatibilization. This review is focused on the behavior of Janus particles in interfacial systems, such as particle-stabilized (i.e., Pickering) emulsions and foams, where stabilization is achieved through the binding of particles to fluid interfaces. In many such applications, the interface could be subjected to deformations, producing compression and shear stresses. Besides the physicochemical properties of the particle, their behavior under flow will also impact the performance of the resulting system. This review article provides a synopsis of interfacial stability and rheology in particle-laden interfaces to highlight the role of the Janus motif, and how particle anisotropy affects interfacial mechanics.

Effect of Sodium Dodecyl Sulfonate on the Foam Stability and Adsorption Configuration of Dodecylamine at the Gas-Liquid Interface

In this study, the effect of sodium dodecyl sulfonate (SDS) on the foam stability of dodecylamine (DDA) and on its adsorption configuration at the gas-liquid interface was investigated. Froth stability experiments, surface tension measurements, time-of-flight secondary-ion mass spectrometry measurements, and molecular dynamics simulation calculations were performed in this investigation. The results revealed that the foam stability of DDA solution was extremely strong, and the addition of SDS could decrease the foam stability when the concentration of DDA was less than a certain value. The decrease in foam stability could be ascribed to several reasons, namely, the big cross-sectional area of SDS at the gas-liquid interface and low adsorption capacity of surfactants at the gas-liquid interface, the high surface tension, the change in the double-layer structure, the small thickness of the gas-liquid interfacial layer, the weak interaction intensity between the head groups of the surfactants and the water molecules, the strong movement ability of the water molecules around the head groups, and the sparse and less upright arrangement configuration of molecules at the gas-liquid interface. These findings can greatly help in solving the strong foam stability problem in DDA flotation and provide a method for reducing foam stability.

Buckling and Drying Kinetics of Particle-Stabilized Water Droplets Fully or Partially Immersed in an Oil Layer

We have investigated the effect of buckling of particle-stabilized water droplets on the drying kinetics. Particle-stabilized water droplets in an oil phase were prepared and the shrinking modes of the droplets during drying were controlled by the wettability of the particles. We obtained water droplets with and without buckling and used them in drying experiments. The drying times were comparable when the droplets were fully immersed in a thick oil layer. However, when the thickness of the oil layer was smaller than the droplet diameter, the buckled droplets showed faster drying. Observation of the reflection images around the droplets suggested that the buckled droplets preferentially shrank in the height direction, while the droplets without buckling isotropically shrank. Mathematical models that assumed diffusion of dissolved water molecules in the oil layer showed good agreement with the experimental data. The effective water-oil interfacial area was constant in the buckled droplets, whereas it shrank in the droplets without buckling. This would be a reason for the faster drying of the partially immersed buckled droplets. Particulate shells on liquid droplets could be used to enhance droplet drying.

Responsive Photonic Liquid Marbles

Liquid marbles have potential to serve as mini-reactors for fabricating new materials, but this has been exploited little and mostly for conventional chemical reactions. Here, we uncover the unparalleled capability of liquid marbles to act as platforms for controlling the self-assembly of a bio-derived polymer, hydroxypropyl cellulose, into a cholesteric liquid crystalline phase showing structural coloration by Bragg reflection. By adjusting the cholesteric pitch via quantitative water extraction, we achieve liquid marbles that we can tailor for structural color anywhere in the visible range. Liquid marbles respond with color change that can be detected by eye, to changes in temperature, exposure to toxic chemicals and mechanical deformation. Our concept demonstrates the advantages of using liquid marbles as a miniature platform for controlling the liquid crystal self-assembly of bio-derived polymers, and their exploitation to fabricate sustainable, responsive soft photonic objects.

Foaming of Oils: Effect of Poly(dimethylsiloxanes) and Silica Nanoparticles

Foaming of oils often confronts researchers in food, cosmetics, and petrochemical industries. Destabilization or stabilization of nonaqueous foams is fundamentally crucial for process control and product quality. Antifoams can be a useful method to control excessive foams. Nonetheless, the foaming mechanisms and the selection criteria of the most common antifoam, poly(dimethylsiloxane) (PDMS) oils, are not thoroughly discussed. The study of inorganic colloidal particles as foam stabilizers has drawn particular attention over the past years practically and academically, yet only a small part of literature focuses on nonaqueous foams. For these reasons, we have studied the effects of PDMS oils and silica nanoparticles on the foaming of oils. We find that the performance of silicone oils as crude oil antifoams is firmly related to PDMS viscosity and crude oil composition presumably because the solubilization of PDMS oils in hydrocarbons reduces with increasing viscosity of the polymers and the hydrocarbons. The findings also illustrate that nanoparticle hydrophobicity and concentration are the primary factors for the foam stabilization effect.

Phase Inversion of Silica Particle-Stabilized Water-in-Water Emulsions

An aqueous two-phase system (ATPS) is of great value in low calorie foods or oil-free cosmetics and pharmaceuticals. In contrast to the recent work on polymer/polymer ATPSs, a simple polymer/salt ATPS (polyethylene glycol/Na₂SO₄) was chosen to study water-in-water (w/w) emulsions stabilized by solid particles. The binodal curve and the tie lines were first determined for the mixture at room temperature. Above the binodal curve, two water-based phases coexist; the upper phase is rich in polymer, whereas the lower phase is rich in salt. Within the two-phase region, we attempted to prepare w/w emulsions with or without the addition of common emulsifiers. Ionic and nonionic surfactants, a polymer, and various solid particles (hydrophilic calcium carbonate particles of different sizes and shapes, wax microspheres) were selected, but no stable emulsion was possible. However, stable w/w emulsions of both types (polymer-in-salt and salt-in-polymer) were formed using dichlorodimethylsilane-modified nanosilica particles. Using partially hydrophobic fumed silica as the emulsifier, emulsions remained fully emulsified for over 1 year and we link the extent of hydrophobization of particles to the properties of the emulsions via contact angle measurements. Furthermore, systematic emulsion studies were conducted at different overall compositions such that changes in emulsion type and stability were mapped onto the phase diagram. Catastrophic phase inversion of emulsion type and evolution of emulsion stability were monitored along the tie lines. Importantly, stability to coalescence was found to decrease approaching conditions of phase inversion.

Enzyme-Loaded Mesoporous Silica Particles with Tuning Wettability as a Pickering Catalyst for Enhancing Biocatalysis

Pickering emulsion systems have created new opportunities for two-phase biocatalysis, however their catalytic performance is often hindered by biphasic mass transfer process relying on the interfacial area. In this study, lipase-immobilized mesoporous silica particles (LMSPs) are employed as both Pickering stabilizers and biocatalysts. A series of alkyl silanes with the different carbon length are used to modify LMSPs to obtain suitable wettability and enlarge the interfacial area of Pickering emulsion. The results show the water/paraffin oil Pickering emulsions stabilized by 8 carbon atoms silane grafted LMSPs (LMSPs_C8) with a three-phase contact angles of 95° get the relatively large interfacial area. Moreover, the conversion of enzymatic reaction catalyzed by LMSPs_C8 Pickering emulsion system is 3.4 times higher than that unmodified LMSPs with the reaction time of 10 min. Additionally, the effective recycling of LMSPs is achieved by simple low-speed centrifugation. As evidenced by a 6-cycles reaction of remaining 75% of relative enzymatic activity, the protection of 350–450 nm mesoporous silica particles can alleviate the inactivation of enzyme from the shear stress and make a benefit to form stabile Pickering emulsion. Therefore, the biphasic reactions in the Pickering emulsion system can be effectively enhanced through changing interfacial area only by the means of adjusting the wettability of biocatalysts.

pH-Responsive Pickering Foams Generated by Surfactant-Free Soft Hydrogel Particles

Pickering foams are foams stabilized by particles and are generally known to have good stability. A special subclass of particle-stabilized foams includes stimuli-responsive Pickering foams that can be formed or deconstructed by applying an external stimuli or changing the environmental conditions; such intelligent particles could find use in many practical applications. Here, we synthesized surfactant-free biocompatible poly[2(diethylamino)ethyl methacrylate] (PDEAEMA) hydrogel particles (HGPs) by emulsion polymerization. The morphology, structure, and surface charge of the HGPs were characterized by TEM, DLS, and the zeta potential, respectively. We have observed that the pH values of the aqueous solution have a strong influence on the formation of the Pickering foams in the presence of PDEAEMA HGPs. Namely, at pH values ≤4.0 no Pickering foams were produced, while at pH values >4.0 stable Pickering foams were formed. Moreover, the height, size and bubble size distribution of Pickering foams are strongly influenced by the pH values of aqueous solution and PDEAEMA HGPs concentration. The formed Pickering foams in basic aqueous solution can all be conveniently deconstructed by changing the pH values to below 4.0. Interestingly, the dried lamellas of the Pickering foams were constituted by either monolayers or multilayers of PDEAEMA HGPs as demonstrated by SEM.

Effects of Contact Angle and Flocculation of Particles of Oligomer of Tetrafluoroethylene on Oil Foaming

Oil foams have been stabilized by using particles of oligomer of tetrafluoroethylene (OTFE). OTFE particles were dispersed in oil mixtures prior to aeration, to exclude the oil-repellency nature of the particles due to the formation of the metastable Cassie-Baxter state and properly evaluate the effects of contact angle on the foaming behavior. The particle contact angle (θ^Y) against air/oil surfaces were controlled by changing a composition of two oils with different surface tension (n-heptane and methyl salicylate). The θ^Y value increases with increasing a mole fraction of methyl salicylate, from 42° (for pure n-heptane) to 89° (for pure methyl salicylate). The air volume incorporated in the oils after aerating OTFE dispersions in the oil mixtures shows a maximum when θ^Y = 55°. The flocculation of OTFE particles in bulk oils is responsible for the unexpected behavior of foaming observed when θ^Y is relatively high. The increase in the degree of the flocculation reduces the effective concentration of OTFE particles in bulk oil, leading to the inefficient bubble stabilization. These findings suggest the efficient oil foaming using particles as a stabilizer is achieved by optimizing both the particle contact angle and the degree of flocculation in oils.

Physico-chemical foundations of particle-laden fluid interfaces

Particle-laden interfaces are ubiquitous nowadays. The understanding of their properties and structure is essential for solving different problems of technological and industrial relevance; e.g. stabilization of foams, emulsions and thin films. These rely on the response of the interface to mechanical perturbations. The complex mechanical response appearing in particle-laden interfaces requires deepening on the understanding of physico-chemical mechanisms underlying the assembly of particles at interface which plays a central role in the distribution of particles at the interface, and in the complex interfacial dynamics appearing in these systems. Therefore, the study of particle-laden interfaces deserves attention to provide a comprehensive explanation on the complex relaxation mechanisms involved in the stabilization of fluid interfaces.

Interaction Mechanism between Molybdenite and Kaolinite in Gypsum Solution Using Kerosene as the Flotation Collector

This paper aims to understand the fundamental interaction mechanism between molybdenite and kaolinite in gypsum solution using kerosene as collector. Micro-flotation tests were conducted to study the effect of gypsum solution on the flotation performance of mixed −74 μm molybdenite and −10 μm kaolinite mineral. The results showed that the recovery of molybdenite decreased from 86% to 74% while the gypsum solution concentration increased from 0 to 800 mg/L, indicating the detrimental effect of kaolinite on molybdenite flotation could be enhanced by gypsum solution. This is mainly caused by the slime coating of kaolinite on molybdenite through dissolved calcium ion of gypsum solution. In order to confirm the slime coating phenomenon, zeta potential distribution, scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurements were used to investigate interaction characteristics and mechanisms. The zeta potential distribution results revealed that mixed samples had the value between signal molybdenite and kaolinite samples in gypsum solution, which proved the coating phenomenon of kaolinite on molybdenite. Moreover, the coating phenomenon was becoming more and more obvious with the gypsum solution concentration. The coating phenomenon of kaolinite on molybdenite surface was also directly observed from SEM results. The AFM results provided further evidence for the possibility of slime coating, as the adhesion force increased with the gypsum solution concentration, which means the aggregates of molybdenite and kaolinite were becoming more stable.

Understanding the role of hydrogen bonding in the aggregation of fumed silica particles in triglyceride solvents

HYPOTHESIS

Fumed silica particles are thought to thicken organic solvents into gels by aggregating to form networks. Hydrogen bonding between silanol groups on different particle surfaces causes the aggregation. The gel structure and hence flow behaviour is altered by varying the proportion of silanol groups on the particle surfaces. However, characterising the gel using rheology measurements alone is not sufficient to optimise the aggregation. We have used confocal microscopy to characterise the changes in the network microstructure caused by altering the particle surface chemistry.

EXPERIMENTS

Organogels were formed by dispersing fumed silica nanoparticles in a triglyceride solvent. The particle surface chemistry was systematically varied from oleophobic to oleophilic by functionalisation with hydrocarbons. We directly visualised the particle networks using confocal scanning laser microscopy and investigated the correlations between the network structure and the shear response of the organogels.

FINDINGS

Our key finding is that the sizes of the pore spaces in the networks depend on the fraction of silanol groups available to form hydrogen bonds. The reduction in the network elasticity of gels formed by methylated particles can be accounted for by the increasing pore size and tenuous nature of the networks. This is the first report that characterises the changes in the microstructure of fumed silica particle networks in non-polar solvents caused by manipulating the particle surface chemistry.

Light and Magnetic Dual-Responsive Pickering Emulsion Micro-Reactors

Emulsion droplets can serve as ideal compartments for reactions. In fact, in many cases, the chemical reactions are supposed to be triggered at a desired position and time without change of the system environment. Here, we present a type of light and magnetic dual-responsive Pickering emulsion microreactor by coadsorption of light-sensitive titania (TiO₂) and super paramagnetic iron oxide (Fe₃O₄) nanoparticles at the oil-water interface of emulsion droplets. The droplets encapsulating different reactants in advance can be driven close to each other by an external magnetic field, and then the chemical reaction is triggered by UV illumination due to the contact of the isolated reactants as a result of droplet coalescence. An insight into the incorporation of hydrophobic TiO₂ and hydrophilic Fe₃O₄ nanoparticles simultaneously at the emulsion interface is achieved. On the basis of that, an account is given of the coalescence mechanism of the Pickering emulsion microreactors. Our work not only provides a novel Pickering emulsion microreactor platform for triggering chemical reactions in a nonintrusive and well-controlled way but also opens a promising avenue to construct multifunctional Pickering emulsions by assembly of versatile building block nanoparticles at the interface of emulsion droplets.

The Potential of Liquid Marbles for Biomedical Applications: A Critical Review

Liquid marbles (LM) are freestanding droplets covered by micro/nanoparticles with hydrophobic/hydrophilic properties, which can be manipulated as a soft solid. The phenomenon that generates these soft structures is regarded as a different method to generate a superhydrophobic behavior in the liquid/solid interface without modifying the surface. Several applications for the LM have been reported in very different fields, however the developments for biomedical applications are very recent. At first, the LM properties are reviewed, namely shell structure, LM shape, evaporation, floatability and robustness. The different strategies for LM manipulation are also described, which make use of magnetic, electrostatic and gravitational forces, ultraviolet and infrared radiation, and approaches that induce LM self-propulsion. Then, very distinctive applications for LM in the biomedical field are presented, namely for diagnostic assays, cell culture, drug screening and cryopreservation of mammalian cells. Finally, a critical outlook about the unexplored potential of LM for biomedical applications is presented, suggesting possible advances on this emergent scientific area.

Foaming Behavior of Polymer-Coated Colloids: The Need for Thick Liquid Films

The current study examined the foaming behavior of poly(vinylpyrrolidone) (PVP)-silica composite nanoparticles. Individually, the two components, PVP and silica nanoparticles, exhibited very little potential to partition at the air-water interface, and as such, stable foams could not be generated. In contrast, combining the two components to form silica-PVP core-shell nanocomposites led to good "foamability" and long-term foam stability. Addition of an electrolyte (Na₂SO₄) was shown to have a marked effect on the foam stability. By varying the concentration of electrolyte between 0 and 0.55 M, three regions of foam stability were observed: rapid foam collapse at low electrolyte concentrations, delayed foam collapse at intermediate concentrations, and long-term stability (∼10 days) at the highest electrolyte concentration. The observed transitions in foam stability were better understood by studying the microstructure and physical and mechanical properties of the particle-laden interface. For rapidly collapsing foams the nanocomposite particles were weakly retained at the air-water interface. The interfaces in this case were characterized as being "liquid-like" and the foams collapsed within 100 min. At an intermediate electrolyte concentration (0.1 M), delayed foam collapse over ∼16 h was observed. The particle-laden interface was shown to be pseudo-solid-like as measured under shear and compression. The increased interfacial rigidity was attributed to adhesion between interpenetrating polymer layers. For the most stable foam (prepared in 0.55 M Na₂SO₄), the ratio of the viscoelastic moduli, G'/G″, was found to be equal to ∼3, confirming a strongly elastic interfacial layer. Using optical microscopy, enhanced foam stability was assessed and attributed to a change in the mechanism of foam collapse. Bubble-bubble coalescence was found to be significantly retarded by the aggregation of nanocomposite particles, with the long-term destabilization being recognized to result from bubble coarsening. For rapidly destabilizing foams, the contribution from bubble-bubble coalescence was shown to be more significant.

Evaporation of Drops Containing Silica Nanoparticles of Varying Hydrophobicities: Exploiting Particle-Particle Interactions for Additive-Free Tunable Deposit Morphology

We describe the systematic and quantitative investigation of a large number of patterns that emerge after the evaporation of aqueous drops containing fumed silica nanoparticles (NPs) of varying wettabilities for an extended particle concentration range. We show that for a chosen system, the dry pattern morphology is mainly determined by particle-particle interactions (Coulomb repulsion and hydrophobic attraction) in the bulk. These depend on both particle hydrophobicity and particle concentration within the drop. For high and intermediate particle concentrations, interparticle hydrophobic attraction is the dominant factor defining the deposit morphology. With increasing particle hydrophobicity, patterns ranging from rings to domes are observed, arising from the time needed for the drop to gel compared with the total evaporation time. On the contrary, drops of dilute suspensions maintain a finite viscosity during most of the drop lifetime, resulting in dry patterns that are predominantly rings for all particle hydrophobicities. In all investigated systems, the NP concentration corresponded to a large excess of NPs in the bulk compared with the maximal amount that could be adsorbed at available interfaces, making particle-interface interactions such as adsorption of hydrophobic NPs at the air-water interface a negligible contribution over bulk particle-particle interactions. This work emphasizes the advantage of particle surface chemistry in tuning both particle-particle interactions and particle deposition onto solid substrates in a robust manner, without the need for any additive such as a surfactant.

Interfacial Activity of Nonamphiphilic Particles in Fluid-Fluid Interfaces

Surfactants can adsorb in fluid-fluid interfaces and lower the interfacial tension. Like surfactants, particles with appropriate wettability can also adsorb in fluid-fluid interfaces. Despite many studies of particle adsorption at fluid interfaces, some confusion persists regarding the ability of (simple, nonamphiphilic) particles to reduce the interfacial tension. In the present work, the interfacial activity of silica nanoparticles at air-water and hexadecane-water interfaces and of ethyl cellulose particles at the interface of water with trimethylolpropane trimethacrylate was analyzed through pendant drop tensiometry. Our measurements strongly suggest that the particles do significantly affect the interfacial tension provided that they have a strong affinity to the interface by virtue of their wettability and that no energy barrier to adsorption prevents them from reaching the interface. A simplistic model that does not explicitly account for any particle-particle interactions is found to yield surprisingly good predictions for the effective interfacial tension in the presence of the adsorbed particles. We further propose that interfacial tension measurements, when combined with information about the particles' wetting properties, can provide a convenient way to estimate the packing density of particles in fluid-fluid interfaces. These results may help to understand and control the assembly of nonamphiphilic nanoparticles at fluid-fluid interfaces, which is relevant to applications ranging from surfactant-free formulations and food technology to oil recovery.

Preparation and characterization of core-shell oil absorption materials stabilized by modified fumed silica

The core-shell oil absorption material (OAM) with fumed silica shell was achieved from Pickering polymerization. The modified fumed silica wall could well stabilize both Pickering emulsion and Pickering polymerization. The particle size of encapsulated OAMs decreased with the increasing concentration of fumed silica and remained unchanged when the concentration was more than 1 wt.%. This fumed silica shell had little effect on the oil absorption rate of OAM. The importance was that the shell reversed the surface property and improved the alkali resistance of OAM. We believe that our core-shell OAMs could reach the self-healing ability of the oil well cement.

Interfacial Particle Dynamics: One and Two Step Yielding in Colloidal Glass

The yielding behavior of silica nanoparticles partitioned at an air-aqueous interface is reported. Linear viscoelasticity of the particle-laden interface can be retrieved via a time-dependent and electrolyte-dependent superposition, and the applicability of the "soft glassy rheology" (SGR) model is confirmed. With increasing electrolyte concentration (φ^elect) in the aqueous subphase, a nonergodic state is achieved with particle dynamics arrested first from attraction induced bonding bridges and then from the cage effect of particle jamming, manifesting in a two-step yielding process under large amplitude oscillation strain (LAOS). The Lissajous curves disclose a shear-induced in-cage particle redisplacement within oscillation cycles between the two yielding steps, exhibiting a "strain softening" transitioning to "strain stiffening" as the interparticle attraction increases. By varying φ^elect and the particle spreading concentration, φ^SiO₂, a variety of phase transitions from fluid- to gel- and glass-like can be unified to construct a state diagram mapping the yielding behaviors from one-step to two-step before finally exhibiting one-step yielding at high φ^elect and φ^SiO₂.

The roles of particles in multiphase processes: Particles on bubble surfaces

Particle-stabilised foams (or froths) form the fundamental framework of industrial processes like froth flotation. This review provides an overview of the effects of particles on bubble surfaces. The characteristics of the particles have a profound effect on the stability of the bubbles although the stabilisation mechanisms may differ. It is well known that layers of particles may provide a steric barrier between two interfaces, which prevents the coalescence of bubbles. Although perhaps considered of lesser importance, it is interesting to note that particles may affect the bubble surface and momentarily suppress coalescence despite being absent from the film separating two bubbles. Foams are at best metastable and coalescence occurs to achieve a state of minimum energy. Despite this, particles have been reported to stabilise bubbles for significant periods of time. Bubble coalescence is accompanied by a release of energy triggered by the sudden change in surface area. This produces a distinctive oscillation of the bubble surface, which may be influenced by the presence of incompressible particles yielding unique surface properties. A survey of the literature shows that the properties of these composite materials are greatly affected by the physicochemical characteristics of the particles such as hydrophobicity and size. The intense energy released during the coalescence of bubbles may be sufficient to expel particles from the bubble surface. It is noted that the detachment of particles may preferentially occur from specific locations on the bubble surface. Examination of the research accounts again reveals that the properties of the particles may affect their detachment upon the oscillation of the bubble surface. However, it is believed that most parameters affecting the detachment of particles are in fact modifying the dynamics of the three-phase line of contact. Both the oscillation of a coalescing bubble and the resulting detachment of particles are highly dynamic processes. They would greatly benefit from computer simulation studies.

Effects of Ionic Strength on the Colloidal Stability and Interfacial Assembly of Hydrophobic Ethyl Cellulose Nanoparticles

Nanoparticle attachment at a fluid interface is a process that often takes place concurrently with nanoparticle aggregation in the bulk of the suspension. Here we investigate systematically the coupling of these processes with reference to the adsorption of aqueous suspensions of ethyl cellulose (EC) nanoparticles at the air-water interface. The suspension stability is optimal at neutral pH and in the absence of salt, conditions under which the electrostatic repulsion among EC nanoparticles is maximized. Nonetheless, hydrophobic attraction dominates particle-interface interactions, resulting in the irreversible adsorption of EC nanoparticles at the air-water interface. The addition of salt weakens the particle-particle and particle-interface repulsive electrostatic forces. This leads to destabilization of the suspension at ionic strengths of 0.05 M or greater but does not affect nanoparticle adsorption. The energy of adsorption, the surface tension and interface coverage at steady state, and the particle contact angle at the interface all remain unchanged by the addition of salt. These findings contribute to the fundamental understanding of colloidal systems and inform the utilization of EC nanocolloids, in particular for the stabilization of foams and emulsions.

Aqueous foams stabilized by chitin nanocrystals

The aim of the present study was to explore the potential use of chitin nanocrystals, as colloidal rod-like particles, to stabilize aqueous foams. Chitin nanocrystals (ChN) were prepared by acid hydrolysis of crude chitin and foams were generated mainly by sonicating the respective dispersions. The foamability of the chitin nanocrystals was evaluated and the resulting foams were assessed for their stability, in terms of foam volume reduction and serum release patterns, during storage. Additionally, the samples were studied with light scattering and optical microscopy in order to explore the bubble size distribution and morphology of the foam. Nanocrystal concentration and charge density was varied to alter the packing of the crystals at the interface. At low concentrations of ChNs, foams were stable against coalescence and disproportionation for a period of three hours, whereas at higher concentrations, the foams were stable for several days. The enhanced stability of foams prepared with ChNs, compared to surfactant-stabilized foams, can be mainly attributed to the irreversible adsorption of the ChNs at the air-water interface, thereby providing Pickering stabilization. Both foam volume and stability of the foam were increased with an increase in ChNs concentration, and at pH values around the chitin's pKa (pH 7.0). Under these conditions, the ChNs show minimal electrostatic repulsion and therefore a higher packing of the nanocrystals is promoted. Moreover, decreased electrostatic repulsion enhances network formation between the ChNs in the aqueous films, thereby providing additional stability by gel formation. Overall, ChNs were proven to be effective in stabilizing foams, and may be useful in the design of Pickering-stabilized food grade foams.

Collapse of Particle-Laden Interfaces under Compression: Buckling vs Particle Expulsion

Colloidal particles can bind to fluid interfaces with a capillary energy that is thousands of times the thermal energy. This phenomenon offers an effective route to emulsion and foam stabilization where the stability is influenced by the phase behavior of the particle-laden interface under deformation. Despite the vast interest in particle-laden interfaces, the key factors that determine the collapse of such an interface under compression have remained relatively unexplored. In this study, we illustrate the significance of the particle surface wettability and presence of electrolyte in the subphase on interparticle interactions at the interface and the resulting collapse mode. Various collapse mechanisms including buckling, particle expulsion, and multilayer formation are reported and interpreted in terms of particle-particle and particle-interface interactions.