Rational design of interfacial properties of ferric (hydr)oxide nanoparticles by adsorption of fatty acids from aqueous solutions

Impact of the Ceria Particle Oxidation State on the Collecting Properties of Sophorolipids and Benzohydroxamic Acid

The search for environmentally friendly alternatives to petroleum-based reagents in mineral processing requires fundamental studies of novel chemicals in model mineral systems. In this study, we evaluate the potential of acidic (ASL) and lactonic sophorolipids (LSL) as collectors in the froth flotation of ultrafine ceria, which serves as a model rare earth mineral (REM). We compare these two biosurfactants to a conventional petroleum-based collector, benzohydroxamic acid (BHA), in the flotation of ceria against hematite and quartz particles. Our research shows the effect of the oxidation state of ceria on its interaction with both conventional and sophorolipid collectors, which can serve as a tool for selective separation in the applied chemistry of froth flotation. It was found that the affinity of the metal oxides to the biosurfactants at pH 4 decreases in the order of α-Fe2O3 > CeO2 (red) > CeO2 (ox), where the best collector of ultrafine ceria against hematite is BHA. To support our findings, we study collector-mineral interactions through mini-flotation tests, adsorption density, contact angle, and zeta potential analyses. In addition, we evaluate the stability of the froth during the flotation of the biosurfactants. Our results indicate that modifying the oxidation state of ceria and using sophorolipids hold promise for the sustainable flotation of REM.

The pH dependent surface charging and points of zero charge. X. Update

Surfaces are often characterized by their points of zero charge (PZC) and isoelectric points (IEP). Different authors use these terms for different quantities, which may be equal to the actual PZC under certain conditions. Several popular methods lead to results which are inappropriately termed PZC. This present review is limited to zero-points obtained in the presence of inert electrolytes (halides, nitrates, and perchlorates of the 1st group metals). IEP are reported for all kinds of materials. PZC of metal oxides obtained as common intersection points of potentiometric curves for 3 or more ionic strengths (or by means of equivalent methods) are also reported, while the apparent PZC obtained by mass titration, pH-drift method, etc. are deliberately neglected. The results published in the recent publications and older results overlooked in the previous compilations by the same author are reported. The PZC/IEP are accompanied by information on the temperature and on the nature and concentration of supporting electrolyte (if available). The references to previous reviews by the same author allow to compare the newest results with the PZC/IEP of similar materials from the older literature.

Adsorption of Cetylpyridinium Chloride at Silica Nanoparticle/Water Interfaces (II): Dependence of Surface Aggregation on Particle Size

Herein, we report a thermodynamic model that relates the adsorption (aggregation) parameters of surfactants at solid/liquid interfaces to particle radius (r). The adsorption (aggregation) parameters include adsorption amounts, equilibrium constants (or the standard Gibbs free energy changes), the critical surface micelle concentration (csmc), and the average aggregation number of surface micelles (n). The model predicts the size dependence of the surface aggregation of surfactants, which is determined by the changes in the interfacial tension and the molar volume of surface components caused by adsorption. In addition, the adsorption of cetylpyridinium chloride (CPyCl), a cationic surfactant, on silica nanoparticles with different r values (ca. 6-61 nm) was determined at 298 K and pH 4, showing an obvious size dependence, consistent with the prediction of the model. With an increase in r, the adsorption isotherm changes from the double-plateau type to the Langmuir type, accompanied by obvious changes in the adsorption parameters. The size-dependent adsorption data can be well described using the model equations, indicating that the model presented here is acceptable. In addition, the model can extract information on the interfacial tensions from adsorption data. We think that the model deepens the understanding of the aggregation phenomena of surfactants at solid/liquid interfaces.

Iron rich self-assembly micelles on the Doce River continental shelf

After the Fundão iron ore mining dam rupture in November 2015, yellow/ocher emulsions never before reported on the continental shelf adjacent to the Doce River began to be seen, both in coalesced and foam forms. XRD analyses pointed to a prevailing composition of iron and kaolinite with a substantial contribution of an organic-metallic compound, measured in multiple periods over 2 years of sampling. Optical microscopy images allowed the identification of micelles composed of nanoparticles of iron oxyhydroxide making up this emulsion. The generation of dendritic snowflake-shaped microcrystals on fiber filters after water sample filtration and heating confirmed the presence of micelles composed of iron oxyhydroxide nanoparticles enveloped by organic polymers. After losing water, the micelles may act as a self-assembly template seed, where the polymer acts in the oriented adsorption of nanoparticles according to their crystallographic structure. The study brought to light the distinct behavior of a portion of the tailings material, which has already been reported to not have the same flocculation process as the clay minerals previously found in the suspended particulate material (SPM) before the dam rupture.

Adsorption of Cetylpyridinium Chloride at Silica Nanoparticle/Water Interfaces (I): Dependence of Adsorption Equilibrium on Particle Size

In the current work, a size-effect model was developed to describe the particle size-dependence of adsorption at solid/liquid interfaces. A parameter, ΔQ_ad, was introduced, defined as the change of the product of the solid/liquid interfacial tension and the molar volume of solid surface components caused by adsorption. The model predicts that with a decrease in particle radius (r), the saturation adsorption amount per unit area (Γ_m, mol/m²) decreases, while the change of the adsorption equilibrium constant (K_ad) is determined by the ΔQ_ad, namely, it decreases if ΔQ_ad > 0 but increases if ΔQ_ad < 0. There exists a critical r at which the saturation adsorption amount per unit mass (Γ_m^g, mol/g) attains a maximum. In addition, the adsorption of cetylpyridinium chloride (CPyCl), a cationic surfactant, on silica nanoparticles with different r (ca. 6-61 nm) values was determined at 298 K and pH 9, showing an obvious size-dependence. With a decrease in r, K_ad and Γ_m decrease, indicating a decrease in the affinity of silica particles toward CPyCl. The size-dependent adsorption data can be well described using our model. Adsorption can affect the molar volume of the solid surface phase, which plays an important role in the size-dependence of adsorption. This work provides a better understanding of the size-dependent adsorption phenomenon at solid/liquid interfaces.

Toward green flotation: Interaction of a sophorolipid biosurfactant with a copper sulfide

The United Nations' Sustainable Development Goals have sparked growing interest in biosurfactants from many surfactant-loaded industries including those utilizing froth flotation for mineral separation. However, the interaction of biosurfactants with mineral surfaces is currently poorly understood. We bridge this gap by studying adsorption of a yeast-derived bola acidic sophorolipid (ASL) biosurfactant on djurleite (Cu_1.94S). The methods used include Hallimond flotation, contact angle, adsorption isotherm, zeta potential, leaching measurements, and X-ray photoelectron spectroscopy (XPS). To facilitate the interpretation of the adsorption results, we characterize the activity of ASL at the air-water interface and measure its critical micelle concentration (CMC) at different pH using static surface tension. We find ASL to be a multifunctional surfactant with an unusual, pH-sensitive interfacial behavior. At the air-water interface, ASL is most active at pH 8, while its CMC goes through minimum as low as 40 μM at pH 7. The surfactant adsorption at the djurleite-water interface makes the sulfide surface hydrophilic at acidic pH and hydrophobic at neutral and basic pH. In addition, ASL has strong affinity to copper sulfide and demonstrates metal leaching properties. Finally, ASL demonstrates detergency properties. We offer a mechanistic interpretation of these findings. Our results provide a basis for the application of acidic glycolipids in froth flotation and have implications for their application in ion separation using hydrometallurgical routes, as well as for the chemical stability of metal sulfides in environmental systems.

Coal emissions adverse human health effects associated with ultrafine/nano-particles role and resultant engineering controls

There are multiple elements which enable coal geochemistry: (1) boiler and pollution control system design parameters, (2) temperature of flue gas at collection point, (3) feed coal and also other fuels like petroleum coke, tires and biomass geochemistry and (4) fuel feed particle size distribution homogeneity distribution, maintenance of pulverisers, etc. Even though there is a large number of hazardous element pollutants in the coal-processing industry, investigations on micrometer and nanometer-sized particles including their aqueous colloids formation reactions and their behaviour entering the environment are relatively few in numbers. X-ray diffraction (XRD), High Resolution-Transmission Electron microscopy (HR-TEM)/ (Energy Dispersive Spectroscopy) EDS/ (selected-area diffraction pattern) SAED, Field Emission-Scanning Electron Microscopy (FE-SEM)/EDS and granulometric distribution analysis were used as an integrated characterization techniques tool box to determine both geochemistry and nanomineralogy for coal fly ashes (CFAs) from Brazil´s largest coal power plant. Ultrafine/nano-particles size distribution from coal combustion emissions was estimated during the tests. In addition the iron and silicon content was determined as 54.6% of the total 390 different particles observed by electron bean, results aimed that these two particles represent major minerals in the environment particles normally. These data may help in future investigations to asses human health actions related with nano-particles.

Adsorption of Lysine on Na-Montmorillonite and Competition with Ca(2+): A Combined XRD and ATR-FTIR Study

Lysine adsorption at clay/aqueous interfaces plays an important role in the mobility, bioavailability, and degradation of amino acids in the environment. Knowledge of these interfacial interactions facilitates our full understanding of the fate and transport of amino acids. Here, X-ray diffraction (XRD) and attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) measurements were used to explore the dynamic process of lysine adsorption on montmorillonite and the competition with Ca(2+) at the molecular level. Density functional theory (DFT) calculations were employed to determine the peak assignments of dissolved lysine in the solution phase. Three surface complexes, including dicationic, cationic, and zwitterionic structures, were observed to attach to the clay edge sites and penetrate the interlayer space. The increased surface coverage and Ca(2+) competition did not affect the interfacial lysine structures at a certain pH, whereas an elevated lysine concentration contributed to zwitterionic-type coordination at pH 10. Moreover, clay dissolution at pH 4 could be inhibited at a higher surface coverage with 5 and 10 mM lysine, whereas the inhibition effect was inconspicuous or undetected at pH 7 and 10. The presence of Ca(2+) not only could remove a part of the adsorbed lysine but also could facilitate the readsorption of dissolved Si(4+) and Al(3+) and surface protonation. Our results provide new insights into the process of lysine adsorption and its effects on montmorillonite surface sites.

Nanoparticulate mineral matter from basalt dust wastes

Ultra-fine and nano-particles derived from basalt dust wastes (BDW) during "stonemeal" soil fertilizer application have been the subject of some concern recently around the world for their possible adverse effects on human health and environmental pollution. Samples of BDW utilized were obtained from companies in the mining district of Nova Prata in southern Brazil for chemical characterization and nano-mineralogy investigation, using an integrated application of advanced characterization techniques such as X-ray diffraction (XRD), High Resolution-Transmission Electron microscopy (HR-TEM)/(Energy Dispersive Spectroscopy) EDS/(selected-area diffraction pattern) SAED, Field Emission-Scanning Electron Microscopy (FE-SEM)/EDS and granulometric distribution analysis. The investigation has revealed that BDW materials are dominated by SiO2, Al2O3 and Fe2O3, with a complex micromineralogy including alkali feldspar, augite, barite, labradorite, hematite, heulandrite, gypsum, kaolinite, quartz, and smectite. In addition we have identified a number of trace metals such as Cd, Cu, Cr, Zn that are preferentially concentrated into the finer, inhalable, dust fraction and could so present a health hazard in the urban areas around the basalt mining zone. The implication of this observation is that use of these nanometric-sized particulates as soil fertilizer may present different health challenges to those of conventional fertilizers, inviting future work regarding the relative toxicities of these materials. Our investigation on the particle size distribution, nano-particle mineralogy and chemical composition in typical BDW samples highlights the need to develop cleaning procedures to minimise exposure to these natural fertilizing basalt dust wastes and is thus of direct relevance to both the industrial sector of basalt mining and to agriculture in the region.

Chemical characterization, nano-particle mineralogy and particle size distribution of basalt dust wastes

Understanding the geochemistry of basalt alteration is central to the study of agriculture systems. Various nano-minerals play an important role in the mobilization of contaminants and their subsequent uptake by plants. We present a new analytical experimental approach in combination with an integrated analytical protocol designed to study basalt alteration processes. Recently, throughout the world, ultra-fine and nano-particles derived from basalt dust wastes (BDW) during "stonemeal" soil fertilizer application have been of great concern for their possible adverse effects on human health and environmental pollution. Samples of BDW utilized were obtained from companies in the Nova Prata mining district in southern Brazil for chemical characterization and nano-mineralogy investigation, using an integrated application of advanced characterization techniques such as X-ray diffraction (XRD), High Resolution-Transmission Electron microscopy (HR-TEM)/Energy Dispersive Spectroscopy (EDS)/(selected-area diffraction pattern) SAED, Field Emission-Scanning Electron Microscopy (FE-SEM/EDS), and granulometric distribution analysis. The investigation has revealed that BDW materials are dominated by SiO2, Al2O3, and Fe2O3, with a complex micromineralogy including alkali feldspar, augite, barite, labradorite, hematite, heulandrite, gypsum, kaolinite, quartz, and smectite. In addition, we have identified a number of trace metals such as Cd, Cu, Cr, and Zn, that are preferentially concentrated into the finer, inhalable, dust fraction and, thus, could present a health hazard in the urban areas around the basalt mining zone. The implication of this observation is that use of these nanometric-sized particulates as soil fertilizer may present different health challenges to those of conventional fertilizers, inviting future work regarding the relative toxicities of these materials. Our investigation on the particle size distribution, nano-particle mineralogy and chemical composition in typical BDW samples highlights the need to develop cleaning procedures to minimize exposure to these natural fertilizing basalt dust wastes and is, thus, of direct relevance to both the industrial sector of basalt mining and to agriculture in the region.

Interactions between nanoparticles and lung surfactant investigated by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

RATIONALE

Inhaled nanoparticles may cause adverse effects due to inactivation of lung surfactants. We have studied how three different nanoparticles interact with dipalmitoyl-phosphatidylcholine (DPPC), the main component in lung surfactant.

METHODS

DPPC in solution was mixed with a suspension of nanoparticles, both in organic solvent, and allowed to interact for 40 min under conditions partly resembling the alveolar lining. Nanoparticles were isolated by centrifugation, washed, and re-suspended in ethanol/water 1:1 (v/v). The resulting solution was analyzed by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOFMS) using dihydroxybenzoic acid as matrix.

RESULTS

The developed methodology was successfully applied for quantitative detection of phospholipid lung surfactant bound to three different types of nanoparticles. Titanium dioxide nanoparticles had a strong affinity for binding of lipid lung surfactant in contrast to pristine and methylated silica nanoparticles. When the concentration of lipid surfactant was raised in the reaction mixture, the titanium dioxide nanoparticles showed an apparently non-linear binding process.

CONCLUSIONS

This work demonstrates that MALDI-TOFMS can be used for direct determination of the binding of surfactant lipids to nanoparticles and represents an important initial step towards a simple and quantitative in vitro method for assessment of interactions of nanoparticles with lung surfactants.

Nano-mineralogical investigation of coal and fly ashes from coal-based captive power plant (India): an introduction of occupational health hazards

Coal derived nano-particles has been received much concern recently around the world for their adverse effects on human health and the environment during their utilization. In this investigation the mineral matter present in some industrially important Indian coals and their ash samples are addressed. Coal and fly ash samples from the coal-based captive power plant in Meghalaya (India) were collected for different characterization and nano-mineralogy studies. An integrated application of advanced characterization techniques such as X-ray diffraction (XRD), High Resolution-Transmission Electron microscopy (HR-TEM)/(Energy Dispersive Spectroscopy) EDS/(selected-area diffraction pattern) SAED, Field Emission-Scanning Electron Microscopy (FE-SEM)/EDS analysis, and Mössbauer spectroscopy were used to know their extent of risks to the human health when present in coal and fly ash. The study has revealed that the coals contain mainly clay minerals, whilst glass fragments, spinel, quartz, and other minerals in lesser quantities were found to be present in the coal fly ash. Fly ash carbons were present as chars. Indian coal fly ash also found to contain nanominerals and ultrafine particles. The coal-fired power plants are observed to be the largest anthropogenic source of Hg emitted to the atmosphere and expected to increase its production in near future years. The Multi Walled Carbon Nano-Tubes (MWCNTs) are detected in our fly ashes, which contains residual carbonaceous matter responsible for the Hg capture/encapsulation. This detailed investigation on the inter-relationship between the minerals present in the samples and their ash components will also be useful for fulfilling the clean coal technology principles.

Constant pH simulations with the coarse-grained MARTINI model — Application to oleic acid aggregates

Long chain fatty acids are biologically important molecules with complex and pH sensitive aggregation behavior. The carboxylic head group of oleic acid is ionizable, with the pKa shifting to larger values, even above a value of 7, in certain aggregate states. While experiments have determined the macroscopic phase behavior, we have yet to understand the molecular level details for this complex behavior. This level of detail is likely required to fully appreciate the role of fatty acids in biology and for nanoscale biotechnological and industrial applications. Here, we introduce the use of constant pH molecular dynamics (MD) simulations with the coarse-grained MARTINI model and apply the method to oleic acid aggregates and a model lipid bilayer. By running simulations at different constant pH values, we determined titration curves and the resulting pKa for oleic acid in different environments. The coarse-grained model predicts positive pKa shifts, with a shift from 4.8 in water to 6.5 in a small micelle, and 6.6 in a dioleoylphosphatidylcholine (DOPC) bilayer, similar to experimental estimates. The size of the micelles increased as the pH increased, and correlated with the fraction of deprotonated oleic acid. We show this combination of constant pH MD and the coarse-grained MARTINI model can be used to model pH-dependent surfactant phase behavior. This suggests a large number of potential new applications of large-scale MARTINI simulations in other biological systems with ionizable molecules.