Enhanced delamination of ultrathin free-standing polymer films via self-limiting surface modification

Achievement of Target Gain Larger than Unity in an Inertial Fusion Experiment

On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G_{target} of 1.5. This is the first laboratory demonstration of exceeding "scientific breakeven" (or G_{target}>1) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb et al. (Indirect Drive ICF Collaboration), Phys. Rev. Lett. 129, 075001 (2022)PRLTAO0031-900710.1103/PhysRevLett.129.075001]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result.

Solvent Evaporation Induced Large-Scale Synthesis of Cs4PbBr6 and CsPbBr3 Microcrystals: Optical Properties and Backlight Application for LEDs

The contemporary work focuses on embossing the emissive nature of lead halide perovskite materials, specifically Cs₄PbBr₆ microcrystal powder prepared via single step bulk recrystallization method followed by the solvent evaporation route from gram to kilogram scale. The X-ray diffraction pattern confirms the formation of phase pure Cs₄PbBr₆ with a goodness of fit value of 1.51 calculated from Rietveld refinement and the fluorophore powder manifesting an intrinsic band gap of 3.76 eV. The experimental yield of 99.4% indicates the absence of any unreacted precursors. The fabricated flexible, free-standing Cs₄PbBr₆@PMMA film encompassed better moisture stability without undergoing phase transitions for 400 days. The temperature-dependent photoluminescence spectra denote that 51% of the intensity was retained when cooled back to room temperature after heating it till 180 °C. Moisture studies at two extreme humidity conditions also reveal the appreciable stability of the fluorophore film against moisture. The stability studies with respect to UV irradiation substantiate that the film retained its stability even after exposing it continuously to UV radiation for seven days. The outstanding optical properties of these microcrystals, owing to the higher exciton binding energy, make them a promising candidate as excellent fluorophores for color conversion, backlight, and light-emitting applications. The Cs₄PbBr₆@PMMA film was employed as the top cover of a commercial blue LED, producing a robust green emission which revealed its possible application as a phosphor material.

Study of Polymer Nanofilms Using for High-Throughput Screening in the Development of Transdermal Therapeutic System

We investigated polymer nanofilm (PNF) for use in high-throughput screening (HTS) to promote the development of transdermal therapeutic systems (TTS). The drug permeability of PNF with a 1 : 1 weight mix ratio of poly(L-lactic acid) (PLLA) and poly(methylhydrosiloxane) (PMHS) (PLLA/PMHS (1/1) PNF) and Strat-M^® of the transdermal diffusion test membrane, was evaluated using 12 kinds of drugs with the logarithmic value of n-octanol/water partition coefficients of -4.70 to 3.86. The lag time of PLLA/PMHS (1/1) PNF made via polymer alloying was significantly shorter than that of Strat-M^® for 10 drug types, and the formation of a highly diffusible PMHS-rich phase accompanying the formation of a sea-island structure was suggested as a contributing factor. Additionally, a high correlation was confirmed between the measured value for the logarithm of the apparent permeability coefficient of PLLA/PMHS (1/1) PNF and the literature values for the logarithm of the apparent permeability coefficient of human skin (r = 0.929). This study shows that PLLA/PMHS (1/1) PNF can reliably predict drug permeability in human skin and can potentially be used in HTS for developing TTS.

Two-Dimensional and Three-Dimensional Ultrathin Multilayer Hydrogels through Layer-by-Layer Assembly

Stimuli-responsive multilayer hydrogels have opened new opportunities to design hierarchically organized networks with properties controlled at the nanoscale. These multilayer materials integrate structural, morphological, and compositional versatility provided by alternating layer-by-layer polymer deposition with the capability for dramatic and reversible changes in volumes upon environmental triggers, a characteristic of chemically cross-linked responsive networks. Despite their intriguing potential, there has been limited knowledge about the structure-property relationships of multilayer hydrogels, partly because of the challenges in regulating network structural organization and the limited set of the instrumental pool to resolve structure and properties at nanometer spatial resolution. This Feature Article highlights our recent studies on advancing assembly technologies, fundamentals, and applications of multilayer hydrogels. The fundamental relationships among synthetic strategies, chemical compositions, and hydrogel architectures are discussed, and their impacts on stimuli-induced volume changes, morphology, and mechanical responses are presented. We present an overview of our studies on thin multilayer hydrogel coatings, focusing on controlling and quantifying the degree of layer intermixing, which are crucial issues in the design of hydrogels with predictable properties. We also uncover the behavior of stratified "multicompartment" hydrogels in response to changes in pH and temperature. We summarize the mechanical responses of free-standing multilayer hydrogels, including planar thin coatings and films with closed geometries such as hollow microcapsules and nonhollow hydrogel microparticles with spherical and nonspherical shapes. Finally, we will showcase potential applications of pH- and temperature-sensitive multilayer hydrogels in sensing and drug delivery. The knowledge about multilayer hydrogels can advance the rational design of polymer networks with predictable and well-tunable properties, contributing to modern polymer science and broadening hydrogel applications.

Disordered Low Molecular Weight Spiropyran Exhibiting Photoregulated Adhesion Ability

The functions of the materials composed of small molecules are highly dependent on their ordered molecular arrangements in both natural and artificial systems. Without ordered structure, small molecules hardly gain complicated functions, due to the absence of intermolecular covalent bond connection or strong network. Here, a low molecular weight spiropyran that could exhibit attractive photochromism and powerful adhesion property in disordered solid state is demonstrated. With maximum up to ∼8 MPa, the adhesion strength could be photoregulated in multiple levels, which also shows one-to-one correspondence to the specific color state. The working mechanism analysis on the photoregulated adhesion reveals that the isomer ratio of merocyanine form and the molecular packing density of spiropyran are the determining factors for the adhesion ability. The discovery of photoregulated adhesion from pure spiropyran provides a new strategy for developing functional materials by employing low molecular weight compounds.

Role of Thin Film Adhesion on Capillary Peeling

The capillary force can peel off a substrate-attached film if the adhesion energy (G_w) is low. Capillary peeling has been used as a convenient, rapid, and nondestructive method for fabricating free-standing thin films. However, the critical value of G_w, which leads to the transition between peeling and sticking, remains largely unknown. As a result, capillary peeling remains empirical and applicable to a limited set of materials. Here, we investigate the critical value of G_w and experimentally show the critical adhesion (G_w,c) to scale with the water-film interfacial energy (≈0.7γ_fw), which corresponds well with our theoretical prediction of G_w,c = γ_fw. Based on the critical adhesion, we propose quantitative thermodynamic guidelines for designing thin film interfaces that enable successful capillary peeling. The outcomes of this work present a powerful technique for thin film transfer and advanced nanofabrication in flexible photovoltaics, battery materials, biosensing, translational medicine, and stretchable bioelectronics.

Ultrahigh Molecular Weight Polyethylene Lamellar-Thin Framework on Square Meter Scale

A new member of low-dimensional structures with a high aspect ratio (LDHA) is introduced. For the first time, commodity polymer is processed into LDHA, which has long been stagnated by the lack of suitable processing techniques. The key to solve the current bottleneck is to overcome the trade-off between kinetic processability and thermodynamic stability. These two factors are both highly determined by intermolecular interaction level (IIL). Thus with a wide tuning range of IIL, ultrahigh molecular weight polyethylene (UHMWPE) is selected and investigated to break through the trade-off. Polymeric LDHA preparation needs both thinning and stiffening. By focusing on one then the other sequentially, they are realized simultaneously. Thus the over sixty-year-old material is finally thinned down by seven orders of magnitude into a 65.5 nm thick and 0.64 m² large lamellar-thin framework (LTF). LTF exhibits a series of exceptional properties such as over-95% transparency, and seven times higher specific strength referred to steel. For the first time, cryogenic electron microscopy (Cryo-EM) is utilized to observe commodity polymers directly. This new LDHA material is promising to expand the scale boundaries of both fundamental research and practical applications, not only for UHMWPE, but also for more commodity polymers to come.

A sub-150-nanometre-thick and ultraconformable solution-processed all-organic transistor

Recent advancements in the field of electronics have paved the way to the development of new applications, such as tattoo electronics, where the employment of ultraconformable devices is required, typically achievable with a significant reduction in their total thickness. Organic materials can be considered enablers, owing to the possibility of depositing films with thicknesses at the nanometric scale, even from solution. However, available processes do not allow obtaining devices with thicknesses below hundreds of nanometres, thus setting a limit. Here, we show an all-organic field effect transistor that is less than 150 nm thick and that is fabricated through a fully solution-based approach. Such unprecedented thickness permits the device to conformally adhere onto nonplanar surfaces, such as human skin, and to be bent to a radius lower than 1 μm, thereby overcoming another limitation for field-effect transistors and representing a fundamental advancement in the field of ultrathin and tattoo electronics.

Spin-coated freestanding films for biomedical applications

Spin-coating is a widely employed technique for the fabrication of thin-film coatings over large areas with smooth and homogeneous surfaces. In recent years, research has extended the scope of spin-coating by developing methods involving the interface of the substrate and the deposited solution to obtain self-supported films, also called freestanding films. Thereby, such structures have been developed for a wide range of areas. Biomedical applications of spin-coated freestanding films include wound dressings, drug delivery, and biosensing. This review will discuss the fundamental physical and chemical processes governing the conventional spin-coating as well as the techniques to obtain freestanding films. Furthermore, developments within this field with a primary focus on tissue engineering applications will be reviewed.

Fabrication and characterization of ultrathin spin-coated poly(L-lactic acid) films suitable for cell attachment and curcumin loading

In the present study, ultrathin poly(L-lactic acid) (PLLA) films were fabricated using the spin-coating technique. Physicochemical properties of the formed materials, including their morphology, thickness, transparency, and contact angle, have been studied. We determined that the morphology of PLLA films could be regulated by changing the polymer concentration and humidity. By altering the humidity, microporous and flat PLLA films can be fabricated. The obtained samples were subsequently used for culturing mesenchymal stem cells and fibroblasts. It has been determined that cells effectively adhered to prepared films and formed on them a monolayer culture with high viability. It has been shown that PLLA films are suitable for the entrapment of curcumin (up to 12.1 μm cm^-2) and provide its sustained release in solutions isotonic to blood plasma. The obtained PLLA films appear to be prospective materials for potential application in regenerative medicine as part of cell-containing tissue engineered dressings for chronic wound treatment.

Roll-to-Roll Transfer of Electrospun Nanofiber Film for High-Efficiency Transparent Air Filter

Particulate matter (PM) pollution in air has become a serious environmental issue calling for new type of filter technologies. Recently, we have demonstrated a highly efficient air filter by direct electrospinning of polymer fibers onto supporting mesh although its throughput is limited. Here, we demonstrate a high throughput method based on fast transfer of electrospun nanofiber film from roughed metal foil to a receiving mesh substrate. Compared with the direct electrospinning method, the transfer method is 10 times faster and has better filtration performance at the same transmittance, owing to the uniformity of transferred nanofiber film (>99.97% removal of PM2.5 at ∼73% of transmittance). With these advantages, large area freestanding nanofiber film and roll-to-roll production of air filter are demonstrated.

Significant enhancement of PEDOT thin film adhesion to inorganic solid substrates with EDOT-acid

With its high conductivity, tunable surface morphology, relatively soft mechanical response, high chemical stability, and excellent biocompatibility, poly(3,4-ethylenedioxythiophene) (PEDOT) has become a promising coating material for a variety of electronic biomedical devices. However, the relatively poor adhesion of PEDOT to inorganic metallic and semiconducting substrates still poses challenges for long-term applications. Here, we report that 2,3-dihydrothieno(3,4-b)(1,4)dioxine-2-carboxylic acid (EDOT-acid) significantly improves the adhesion between PEDOT thin films and inorganic solid electrodes. EDOT-acid molecules were chemically bonded onto activated oxide substrates via the chemisorption of the carboxylic groups. PEDOT was then polymerized onto the EDOT-acid modified substrates, forming covalently bonded coatings. The adsorption of EDOT-acid onto the electrode surfaces was characterized by cyclic voltammetry (CV), contact angle measurements, atomic force microscopy, and X-ray photoelectron spectroscopy. The electrical properties of the subsequently coated PEDOT films were studied by electrochemical impedance spectroscopy and CV. An aggressive ultrasonication test confirmed the significantly improved adhesion and mechanical stability of the PEDOT films on electrodes with EDOT-acid treatment over those without treatment.

Fabrication of Large-area Free-standing Ultrathin Polymer Films

This procedure describes a method for the fabrication of large-area and ultrathin free-standing polymer films. Typically, ultrathin films are prepared using either sacrificial layers, which may damage the film or affect its mechanical properties, or they are made on freshly cleaved mica, a substrate that is difficult to scale. Further, the size of ultrathin film is typically limited to a few square millimeters. In this method, we modify a surface with a polyelectrolyte that alters the strength of adhesion between polymer and deposition substrate. The polyelectrolyte can be shown to remain on the wafer using spectroscopy, and a treated wafer can be used to produce multiple films, indicating that at best minimal amounts of the polyelectrolyte are added to the film. The process has thus far been shown to be limited in scalability only by the size of the coating equipment, and is expected to be readily scalable to industrial processes. In this study, the protocol for making the solutions, preparing the deposition surface, and producing the films is described.

Insulating and semiconducting polymeric free-standing nanomembranes with biomedical applications

Free-standing nanomembranes, which are emerging as versatile elements in biomedical applications, are evolving from being composed of insulating (bio)polymers to electroactive conducting polymers.

Reconstruction of 2D x-ray radiographs at the National Ignition Facility using pinhole tomography (invited)

Two-dimensional radiographs of imploding fusion capsules are obtained at the National Ignition Facility by projection through a pinhole array onto a time-gated framing camera. Parallax among images in the image array makes it possible to distinguish contributions from the capsule and from the backlighter, permitting correction of backlighter non-uniformities within the capsule radiograph. Furthermore, precise determination of the imaging system geometry and implosion velocity enables combination of multiple images to reduce signal-to-noise and discover new capsule features.

Monolayer graphene-supported free-standing PS-b-PMMA thin film with perpendicularly orientated microdomains

A facile way to fabricate robust free-standing PS-b-PMMA thin films with perpendicularly orientated microdomains on monolayer graphene is reported.