Loading and protection of hydrophilic molecules into liposome-templated polyelectrolyte nanocapsules

Ecofriendly Controlled-Release Insecticide Carrier: pH-/Temperature-Responsive Rosin-Derived Hydrogels for Avermectin Delivery against Mythimna separata (Walker)

The exploration of environmentally friendly, less toxic, sustained-release insecticide is increasing with the growing demand for food to meet the requirements of the expanding population. As a sustained-release carrier, the unique, environmentally friendly intelligent responsive hydrogel system is an important factor in improving the efficiency of insecticide utilization and accurate release. In this study, we developed a facile approach for incorporating the natural compound rosin (dehydroabietic acid, DA) and zinc ions (Zn2+) into a poly(N-isopropylacrylamide) (PNIPAM) hydrogel network to construct a controlled-release hydrogel carrier (DA-PNIPAM-Zn2+). Then, the model insecticide avermectin (AVM) was encapsulated in the carrier at a drug loading rate of 36.32% to form AVM@DA-PNIPAM-Zn2+. Surprisingly, the smart controlled carrier exhibited environmental responsiveness, strongly enhanced mechanical properties, self-healing ability, hydrophobicity, and photostability to ensure a balance between environmental friendliness and the precision of the drug release. The release experiments showed that the carboxyl and amide groups in the polymer chains alter the intermolecular forces within the hydrogel meshes and ingredient diffusion by changing temperatures (25 and 40 °C) and pH values (5.8, 7.4, and 8.5), leading to different release behaviors. The insecticidal activity of the AVM@DA-PNIPAM-Zn2+ against oriental armyworms was good, with an effective minimum toxicity toward aquatic animals. Therefore, AVM@DA-PNIPAM-Zn2+ is an effective drug delivery system against oriental armyworms. We anticipate that this ecofriendly, sustainable, smart-response carrier may broaden the utilization rosin and its possible applications in the agricultural sector.

Curcumin Modulates 1,2-dibehenoyl-sn-glycero-3-phosphocholine (DBPC) Liposomes: Chitosan Oligosaccharide Lactate Influences Membrane Fluidity But Does Not Alter Phase Transition Temperature of DBPC Liposomes

1,2-dibehenoyl-sn-glycero-3-phosphocholine (DBPC) is one of the important phospholipids found in cell membrane but not studied well. Importance of curcumin as a dietary supplement and for its medicinal properites is getting widely recoginsed. The present study for the first time explores the effect of curcumin on properties of DBPC liposomes by monitoring the fluorescence properties of curcumin. The phase transition temperature (Tm) of DBPC is assessed which confirms increase in curcumin concentration causes a slight drop in the Tm value. Chitosan is being applied for various drug delivery uses. The study establishes new insight on effect of chitosan oligosaccharide lactate on DBPC liposomes. It is found that in the absence of chitosan oligosaccharide lactate, curcumin partitions more strongly in the liquids crystalline phase than in the solid gel phase, however, the opposite result is obtained with the presence of chitosan oligosaccharide lactate which penetrates into the DBPC liposomes membranes at higher temperature, blocking thus the passage of curcumin into the lipid bilayer. However, addition of chitosan oligosaccharide lactate had no effect on the Tm. Fluorescence quenching study of curcumin establishes that the location of curcumin to be in the hydrophobic cavity of DBPC membrane.

Towards the systematic design of multilayer O/W emulsions with tannic acid as an interfacial antioxidant

This work discusses the possibility of designing multilayer oil-in-water emulsions to introduce the maximum possible amount of an antioxidant at the droplet interfaces for the optimal protection of a linseed oil core against oxidation, using a systematic three-step colloidal procedure. An antioxidant (here Tannic Acid - TA) is chosen and its interactions with a primary emulsifier (here Bovine Serum Albumin - BSA) and several polysaccharides are first examined in solution using turbidity measurements. As a second step, LbL deposition on solid surfaces is used to determine which of the polysaccharides to combine with BSA and tannic acid in a multilayer system to ensure maximum presence of tannic acid in the films. From UV-vis and polarization modulation infrared reflection-absorption (PM-IRRAS) spectroscopic measurements it is suggested that the best components to use in a multilayer emulsion droplet, together with BSA and TA, are chitosan and pectin. BSA, chitosan and pectin are subsequently used for the formation of three-layer linseed oil emulsions, and tannic acid is introduced into any of the three layers as an antioxidant. The effect of the exact placement of tannic acid on the oxidative stabilization of linseed oil is assessed by monitoring the fluorescence of Nile red, dissolved in the oil droplets, under the attack of radicals generated in the aqueous phase of the emulsion. From the results it appears that the three-stage procedure presented here can serve to identify successful combinations of interfacial components of multilayer emulsions. It is also concluded that the exact interfacial placement of the antioxidant plays an important role in the oxidative stabilization of the valuable oil core.

Polyelectrolyte Multilayers on Soft Colloidal Nanosurfaces: A New Life for the Layer-By-Layer Method

The Layer-by-Layer (LbL) method is a well-established method for the assembly of nanomaterials with controlled structure and functionality through the alternate deposition onto a template of two mutual interacting molecules, e.g., polyelectrolytes bearing opposite charge. The current development of this methodology has allowed the fabrication of a broad range of systems by assembling different types of molecules onto substrates with different chemical nature, size, or shape, resulting in numerous applications for LbL systems. In particular, the use of soft colloidal nanosurfaces, including nanogels, vesicles, liposomes, micelles, and emulsion droplets as a template for the assembly of LbL materials has undergone a significant growth in recent years due to their potential impact on the design of platforms for the encapsulation and controlled release of active molecules. This review proposes an analysis of some of the current trends on the fabrication of LbL materials using soft colloidal nanosurfaces, including liposomes, emulsion droplets, or even cells, as templates. Furthermore, some fundamental aspects related to deposition methodologies commonly used for fabricating LbL materials on colloidal templates together with the most fundamental physicochemical aspects involved in the assembly of LbL materials will also be discussed.

Oral delivery of all-trans retinoic acid mediated by liposome carriers

All-trans retinoic acid (ATRA) is a molecule that finds wide applications in medicine. Connection between cancer cell proliferation and ATRA is a well-established item. Driven by the potential applications of liposomes in stabilizing and protecting therapeutic compounds thus enabling effective delivery of encapsulated compounds, recent research efforts have been directed to understanding mechanisms of oral delivery through the gastrointestinal tract. The surface charge of the liposome bilayers can modify the interactions between the aggregates and the gastrointestinal fluids. Here, we investigated the ability of cationic and anionic liposomes to encapsulate, protect and deliver ATRA in an in-vitro digestion process as a different oral administration route. Stability and encapsulation efficiency of ATRA in negatively and positively charged liposomes enriched with α-tocopherol were investigated by means of UV-vis spectroscopy, dynamic light scattering and ζ-potential. The applicability of the carriers was tested by means of an in-vitro digestion procedure allowing for the measurement of the bioavailability of ATRA. From this study evidence was provided that the water insoluble molecules, ATRA and α-tocopherol are intercalated in liposome membranes regardless of the surface charge of the vesicle bilayers. Comparisons between cationic and anionic liposomes incorporating retinoic acid show differences in bioavailability. The cationic vesicles are preferable for a larger amount of ATRA bioavailability, which can be understood from electrostatic interactions. Thus ATRA is ionized in a wide range of pHs but protonated in anionic vesicles.

The influence of PBAT content in the nanocapsules preparation and its effect in essential oils release

Nanoencapsulation provides new alternatives for the food industry, enabling a controlled and slow release of active antimicrobial agents, such as essential oils (EO). Poly (butylene adipate-co-terephthalate) (PBAT) nanocapsules loaded with linalool EO were prepared using an extrusion method with 1, 3, and 5% w/v (PBAT to chloroform). Nanocapsules' sizes ranged from 100 to 250 nm and were spherical. The release profile was studied using an ethanoic medium over 24 h, and according to the Korsmeyer-Peppas model, a Fick diffusion mechanism was involved. FT-IR and thermogravimetric analyses confirmed EO encapsulation with an encapsulation efficiency of 55%, 71%, and 74% for 1, 3, and 5%, respectively. The results indicated that encapsulation depended on organic phase concentration, with higher PBAT contents achieving better results. The resulting nanocapsules had antimicrobial activity against E. coli, which could be extended to develop active packaging systems.

Interplay of the Assembly Conditions on Drug Transport Mechanisms in Polyelectrolyte Multilayer Films

The layer-by-layer film deposition is a suitable strategy for the design and functionalization of drug carriers with superior performance, which still lacks information describing the influence of assembly conditions on the mechanisms governing the drug release process. Herein, traditional poly(acrylic acid)/poly(allylamine) polyelectrolyte multilayers (PEM) were explored as a platform to study the influence of the assembly conditions such as pH, drug loading method, and capping layer deposition on the mechanisms that control the release of calcein, the chosen model drug, from PEM. Films with 20-40 bilayers were assembled at pH 4.5 or 8.8, and the drug loading process was carried out during- or post-film assembly. Release data were fitted to three release models, namely, Higuchi, Ritger-Peppas, and Berens-Hopfenberg, to investigate the mechanism governing the drug transport, such as the apparent diffusion and the relaxation time. The postassembly drug loading method leads to a higher drug loading capacity than the during-assembly method, attributed to the washing out of calcein during film assembly steps in the latter method. Higuchi's and Ritger-Peppas' model analyses indicate that the release kinetic constant increased with the number of bilayers for the postassembly method. The opposite trend is observed for the during-assembly method. The Berens-Hopfenberg release model enabled the decoupling of each drug transport mechanism's contribution, indicating the increase of the diffusion contribution with the number of bilayers for the postassembly method at pH 4.5 and the increase of the polymer relaxation contribution for the during-assembly method at pH 8.8. Deborah's number, which represents the ratio of the polymer relaxation time to the diffusion time, follows the trends observed for the relaxation contribution for the conditions investigated. The deposition of the capping phospholipid layer over the payload also favored the polymer relaxation contribution in the drug release, featuring new strategies to investigate the drug release in PEM.

Binary Solutions of Hyaluronan and Lactose-Modified Chitosan: The Influence of Experimental Variables in Assembling Complex Coacervates

A miscibility study between oppositely charged polyelectrolytes, namely hyaluronic acid and a lactose-modified chitosan, is here reported. Experimental variables such as polymers' weight ratios, pH values, ionic strengths and hyaluronic acid molecular weights were considered. Transmittance analyses demonstrated the mutual solubility of the two biopolymers at a neutral pH. The onset of the liquid-liquid phase separation due to electrostatic interactions between the two polymers was detected at pH 4.5, and it was found to be affected by the overall ionic strength, the modality of mixing and the polymers' weight ratio. Thorough Dynamic Light Scattering (DLS) measurements were performed to check the quality of the formed coacervates by investigating their dimensions, homogeneity and surface charge. The whole DLS results highlighted the influence of the hyaluronic acid molecular weight in affecting coacervates' dispersity and size.

Nanohybrid carriers: the yin–yang equilibrium between natural and synthetic in biomedicine

Nanocarriers are key players in biomedicine applications. The development of hybrid nanoparticles stems from the need to enhance their quality by lowering disadvantages and fusing the positive qualities of both natural and synthetic materials.

Deciphering and Controlling Structural and Functional Parameters of the Shells in Vesicle-Templated Polymer Nanocapsules

Vesicle-templated nanocapsules are prepared by polymerization of hydrophobic acrylic monomers and cross-linkers in the hydrophobic interior of self-assembled bilayers. Understanding the mechanism of capsule formation and the influence of synthetic parameters on the structural features and functional performance of nanocapsules is critical for the rational design of functional nanodevices, an emerging trend of application of the nanocapsule platform. This study investigated the relationship between basic parameters of the formulation and synthesis of nanocapsules and structural and functional characteristics of the resulting structures. Variations in the monomer/surfactant ratio, temperature of polymerization, and the molar fraction of the free-radical initiators were investigated with a multipronged approach, including shell thickness measurements using small-angle neutron scattering, evaluation of the structural integrity of nanocapsules with scanning electron microscopy, and determination of the retention of entrapped molecules using absorbance and fluorescence spectroscopy. Surprisingly, the thickness of the shells did not correlate with the monomer/surfactant ratio, supporting the hypothesis of substantial stabilization of the surfactant bilayer with loaded monomers. Decreasing the temperature of polymerization had no effect on the spherical structure of nanocapsules but resulted in progressively lower retention of entrapped molecules, suggesting that a spherical skeleton of nanocapsule forms rapidly, followed by filling the gaps to create the structure without pinholes. Lower content of initiators resulted in slower reactions, outlining the baseline conditions for practical synthetic protocols. Taken together, these findings provide insights into the formation of nanocapsules and offer methods for controlling the properties of nanocapsules in viable synthetic methods.

Synthesis of silica-alginate nanoparticles and their potential application as pH-responsive drug carriers

Composite silica-alginate nanoparticles were prepared via silica sol-gel technique using a water-in-oil microemulsion system. In our system, cyclohexane served as the bulk oil phase into which aqueous solutions of sodium alginate were dispersed as droplets that confined nanoparticle formation after addition of tetraethylorthosilicate (TEOS). Our studies showed that much of the particle growth is completed within the first 24 hours and reaction times up to 120 hours only resulted in an additional 5% increase in particle diameter. Average particle size was found to decrease with increasing water-to-surfactant molar ratio (R) and with increasing cocentration of alginate in the aqueous phase. The potential for drug loading during particle formation was demonstrated using rhodamine B as a model drug. In vitro release studies showed that particles incubated in pH 2.5 phosphate buffer released only about 7% of the drug load in 27 days, while 42% was released in pH 7.5 phosphate buffer over the same period. Analysis of the release profile suggested that rhodamine B was homogeneously distributed throughout the particle and that the drug diffusivity was 40-fold greater in pH 7.5 buffer compared to that at pH 2.5. These results suggest that silica-alginate nanoparticles could be used as a pH-responsive drug carrier for controlled drug release.

Rheological Characterization of Hydrogels from Alginate-Based Nanodispersion

The interest toward alginate and nanoemulsion-based hydrogels is driven by the wide potential of application. These systems have been noticed in several areas, ranging from pharmaceutical, medical, coating, and food industries. In this investigation, hydrogels prepared through in situ calcium ion release, starting from lemongrass essential oil nanodispersions stabilized in alginate aqueous suspensions in the presence of the nonionic surfactant Tween 80, were evaluated. The hydrogels prepared at different concentrations of oil, alginate, and calcium were characterized through rheological tests. Flow curves demonstrate that the hydrogels share shear thinning behavior. Oscillatory tests showed that the strength of the hydrogel network increases with the crosslinker increase, and decreases at low polymer concentrations. The hydrogels were thixotropic materials with a slow time of structural restoration after breakage. Finally, by analyzing the creep recovery data, the hydrogel responses were all fitted to the Burger model. Overall, it was demonstrated that the presence of essential oil in the proposed hydrogels does not affect the mechanical characteristics of the materials, which are mainly influenced by the concentration of polymer and calcium as a crosslinker.

Polymer Capsules for Enzymatic Catalysis in Confined Environments

Catalysis is at the base of a series of biological and technological application processes. In recent years, the tendency has developed to carry out catalyzed reactions within confined structures, thus forming systems called micro or nanoreactors. Compartmentalized structures are cavities delimited by a wall where specific functions are introduced with a defined concentration and in the desired sites. These containers are generally referred to as nano or microcapsules, assuming the function of reactors in the presence of chemical reactions. Among the various types of existing structures, one of the most interesting is represented by systems made with polymers. This review aims to highlight some of the current advances in the use of functionalized structures that are useful for catalysis reactions, paying particular attention to polymer capsules and enzymes. The built-up methods used for the production of polymer capsules, as well as the aspects that influence membrane permeability and reactivity to environmental conditions, are discussed. Recent advances on biocatalysis confined in polymeric capsules are illustrated, and the strengths and weaknesses of the principal nanoreactors are considered.

Direct CNS delivery of proteins using thermosensitive liposome-in-gel carrier by heterotopic mucosal engrafting

Delivering therapeutics across the blood-brain barrier (BBB) for treating central nervous system (CNS) diseases is one of the biggest challenges today as the BBB limits the uptake of molecules greater than 500 Da into the CNS. Here we describe a novel trans-nasal mucosal drug delivery as an alternative to the intranasal drug delivery to overcome its limitations and deliver high molecular weight (HMW) therapeutics efficiently to the brain. This approach is based on human endoscopic skull base surgical techniques in which a surgical defect is repaired by engrafting semipermeable nasal mucosa over a skull base defect. Based on endoscopic skull based surgeries, our groups has developed a trans-nasal mucosal rodent model where we have evaluated the permeability of ovalbumin (45 kDa) as a model protein through the implanted mucosal graft for delivering HMW therapeutics to the brain. A thermo sensitive liposome-in-gel (LiG) system was developed for creating a drug depot allowing for a sustained release from the site of delivery to the brain through the implanted nasal graft. We would like to report this as an exploratory pilot study where we are using this novel surgical model to show that the implanted nasal mucosal graft and the LiG delivery system result in an efficient and a sustained brain delivery of HMW proteins. Hence, this study demonstrates that the trans-nasal mucosal engrafting technique could overcome the limitations for intranasal drug delivery and enable the uptake of HMW protein therapeutics into the CNS for the treatment of a wide range of neurodegenerative diseases.

Internal Structure of Matrix-Type Multilayer Capsules Templated on Porous Vaterite CaCO₃ Crystals as Probed by Staining with a Fluorescence Dye

Multilayer capsules templated on decomposable vaterite CaCO₃ crystals are widely used as vehicles for drug delivery. The capsule represents typically not a hollow but matrix-like structure due to polymer diffusion into the porous crystals during multilayer deposition. The capsule formation mechanism is not well-studied but its understanding is crucial to tune capsule structure for a proper drug release performance. This study proposes new approach to noninvasively probe and adjust internal capsule structure. Polymer capsules made of poly(styrene-sulfonate) (PSS) and poly(diallyldimethylammonium chloride) (PDAD) have been stained with fluorescence dye rhodamine 6G. Physical-chemical aspects of intermolecular interactions required to validate the approach and adjust capsule structure are addressed. The capsules consist of a defined shell (typically 0.5⁻2 µm) and an internal matrix of PSS-PDAD complex (typically 10⁻40% of a total capsule volume). An increase of ionic strength and polymer deposition time leads to the thickening of the capsule shell and formation of a denser internal matrix, respectively. This is explained by effects of a polymer conformation and limitations in polymer diffusion through the crystal pores. We believe that the design of the capsules with desired internal structure will allow achieving effective encapsulation and controlled/programmed release of bioactives for advanced drug delivery applications.

Rheological Properties of Alginate–Essential Oil Nanodispersions

Due to its favorable structural properties and biocompatibility, alginate is recognized as a suitable versatile biopolymer for use in a broad range of applications ranging from drug delivery, wound healing, tissue engineering, and food formulations such as nanodispersions. Rheological analysis plays a crucial role in the design of suitable nanoemulsion based coatings. Different essential oil and alginate nanodispersion compositions stabilized by Tween 80 were analyzed for rheological and conductometric properties. The results confirmed that the nanoformulations shared a pseudoplastic non-Newtonian behavior that was more evident with higher alginate concentrations (2%). Nanodispersions made of alginate and essential oil exhibited a slight thixotropic behavior, demonstrating the aptitude to instantaneously recover from the applied stress or strain. Oscillatory frequency sweep tests showed a similar fluid-like behavior for 1% and 2% alginate nanodispersions. Finally, it was demonstrated that advantages coming with the use of the essential oil are added to the positive aspects of alginate with no dramatic modification on the flow behavior.

Layer-by-layer Polyelectrolytes Coating of Alginate Microgels for Sustained Release of Sodium Benzoate and Zosteric Acid

The potential of sustaining release of very small (Mw < 250 g/mol) hydrophilic drugs up to several days from layer-by-layer (LbL) polyelectrolyte coated alginate microgels (Alg-Ms) was investigated. One purpose is to minimize post-surgical adhesions, which develop in 12 h to 3 days after surgery. The LbL polyelectrolyte layer would serve as a diffusion barrier for their release. The LbL polyelectrolyte bilayers were prepared using poly(allylamine) (PAH) and poly(styrene sulfonate) (PSS). Sodium benzoate (NaB, Mw = 144 g/mol) and zosteric acid (ZA, Mw = 244 g/mol), two anti-inflammatory and anti-microbial compounds, were used as model drugs. A higher number of PAH/PSS bilayer lead to a greater sustained release of both drugs, and with 4 bilayers, the release of NaB and ZA was prolonged from 24 h to 72 h and 120 h, respectively. Fitting the data to the Ritger-Peppas' equation showed that as the bilayer number increased, the release constant and/or exponent decreased, indicating the LbL PAH/PSS bilayer effectively reduced the permeability of these two very small hydrophilic drugs. The ability to prolong the release of such small hydrophilic molecules, which has rarely been investigated previously, would find broad applications in fields such as anti-adhesion treatment and antifouling coatings.

AMF responsive DOX-loaded magnetic microspheres: transmembrane drug release mechanism and multimodality postsurgical treatment of breast cancer

DOX-loaded magnetic alginate–chitosan microspheres were developed to evaluate alternating magnetic field-responsive, synergistic chemo-thermal cancer therapy.

l-Phenylalanine-Tethered, Naphthalene Diimide-Based, Aggregation-Induced, Green-Emitting Organic Nanoparticles

The present article delineates the formation of green fluorescent organic nanoparticle through supramolecular aggregation of naphthalene diimide (NDI)-based, carboxybenzyl-protected, l-phenylalanine-appended bola-amphiphile, NDI-1. The amphiphilic molecule is soluble in DMSO, and, with gradual addition of water within the DMSO solution, the amphiphile starts to self-assemble via H-type aggregation to form spherical nanoparticles. These self-assembly of NDI-1 in the presence of a high amount of water exhibited aggregation-induced emission (AIE) through excimer formation. Notably, in the presence of 99% water content, the amphiphile forms spherical aggregated nanoparticles as confirmed from microscopic investigations and dynamic light scattering study. Interestingly, the emission maxima of molecularly dissolved NDI-1 (weak blue fluorescence) red-shifted upon aggregation with increase in water concentration and led to the formation of green-emitting fluorescent organic nanoparticles (FONPs) at 99% water content. These green-emitting FONPs were utilized in cell imaging as well as for efficient transportation of anticancer drug curcumin inside mammalian cells.

Spontaneous Formation of a Vesicular Assembly by a Trimesic Acid Based Triple Tailed Amphiphile

Trimesic acid based amino acid functionalized triple tailed amphiphiles (TMA-1 and TMA-2) were synthesized. The triskelion amphiphile TMA-1 with a neutral side chain self-assembled into a vesicle in 2:1 (v/v) DMSO-water, while the ammonium side chain decorated TMA-2 formed vesicles in pure water. Microscopic and spectroscopic characterizations were carried out to confirm the self-aggregated vesicular morphology and its size which is around 250-300 nm in the case of TMA-1 and around 100-150 nm for TMA-2 vesicles. The unique structure of these amphiphiles with an aromatic core and three hydrophilic side chains led to an interlamellar orientation of their hydrophobic (aromatic) domain, while hydrophilic terminals were directed toward the aqueous domain. These amphiphiles formed monolayered vesicles possibly through H-aggregation during the process of self-assembly, which is different from conventional bilayered vesicles formed by twin-chain lipid molecules. The time resolved decay curve of hydrophobic dye entrapped within these vesicles indicated that the hydrophobicity within the microenvironment of TMA-1 and TMA-2 vesicles is higher than that in pure water; however, at the same time, it is comparatively lower than that observed in bilayered phosphocholine vesicles. Furthermore, calcein dye was entrapped within these vesicles to ensure their encapsulation efficiency (65-85%). The ability to entrap dye molecules by these synthesized vesicles was utilized to encapsulate and deliver anticancer drug doxorubicin inside the mammalian cells. A simple synthetic procedure and facile aggregation to vesicular self-assembly with superior dye/drug encapsulation proficiency made these vesicles a potential cellular transporter.

X-DNA origami-networked core-supported lipid stratum

DNA hydrogels are promising materials for various fields of research, such as in vitro protein production, drug carrier systems, and cell transplantation. For effective application and further utilization of DNA hydrogels, highly effective methods of nano- and microscale DNA hydrogel fabrication are needed. In this respect, the fundamental advantages of a core-shell structure can provide a simple remedy. An isolated reaction chamber and massive production platform can be provided by a core-shell structure, and lipids are one of the best shell precursor candidates because of their intrinsic biocompatibility and potential for easy modification. Here, we demonstrate a novel core-shell nanostructure made of gene-knitted X-shaped DNA (X-DNA) origami-networked gel core-supported lipid strata. It was simply organized by cross-linking DNA molecules via T4 enzymatic ligation and enclosing them in lipid strata. As a condensed core structure, the DNA gel shows Brownian behavior in a confined area. It has been speculated that they could, in the future, be utilized for in vitro protein synthesis, gene-integration transporters, and even new molecular bottom-up biological machineries.