Packing efficiency of small silica particles on large latex particles: a facile route to colloidal nanocomposites

Effect of Temperature, Oil Type, and Copolymer Concentration on the Long-Term Stability of Oil-in-Water Pickering Nanoemulsions Prepared Using Diblock Copolymer Nanoparticles

A poly(glycerol monomethacrylate) (PGMA) precursor was chain-extended with 2,2,2-trifluoroethyl methacrylate (TFEMA) via reversible addition-fragmentation chain transfer (RAFT) aqueous emulsion polymerization. Transmission electron microscopy (TEM) studies confirmed the formation of well-defined PGMA52-PTFEMA50 spherical nanoparticles, while dynamic light scattering (DLS) studies indicated a z-average diameter of 26 ± 6 nm. These sterically stabilized diblock copolymer nanoparticles were used as emulsifiers to prepare oil-in-water Pickering nanoemulsions: either n-dodecane or squalane was added to an aqueous dispersion of nanoparticles, followed by high-shear homogenization and high-pressure microfluidization. The Pickering nature of such nanoemulsion droplets was confirmed via cryo-transmission electron microscopy (cryo-TEM). The long-term stability of such Pickering nanoemulsions was evaluated by analytical centrifugation over a four-week period. The n-dodecane droplets grew in size significantly faster than squalane droplets: this is attributed to the higher aqueous solubility of the former oil, which promotes Ostwald ripening. The effect of adding various amounts of squalane to the n-dodecane droplet phase prior to emulsification was also explored. The addition of up to 40% (v/v) squalane led to more stable nanoemulsions, as judged by analytical centrifugation. The nanoparticle adsorption efficiency at the n-dodecane-water interface was assessed by gel permeation chromatography when using nanoparticle concentrations of 4.0, 7.0, or 10% w/w. Increasing the nanoparticle concentration not only produced smaller droplets but also reduced the adsorption efficiency, as confirmed by TEM studies. Furthermore, the effect of varying the nanoparticle concentration (2.5, 5.0, or 10% w/w) on the long-term stability of n-dodecane-in-water Pickering nanoemulsions was explored over a four-week period. Nanoemulsions prepared at higher nanoparticle concentrations were more unstable and exhibited a faster rate of Ostwald ripening. The nanoparticle adsorption efficiency was monitored for an aging nanoemulsion prepared at a copolymer concentration of 2.5% w/w. As the droplets ripened over time, the adsorption efficiency remained constant (∼97%). This suggests that nanoparticles desorbed from the shrinking smaller droplets and then readsorbed onto larger droplets over time. Finally, the effect of temperature on the stability of Pickering nanoemulsions was examined. Storing these Pickering nanoemulsions at elevated temperatures led to faster rates of Ostwald ripening, as expected.

Advances in Organic-Inorganic Hybrid Latex Particles via In Situ Emulsion Polymerization

Hybrid latex particles combine the unique properties of inorganic nano/micro particles with the inherent properties of polymers, exhibiting tremendous potential for a variety of applications. Recent years have witnessed an increased interest in the design and preparation of hybrid latex particles with well-defined size, structure and morphology. Due to its simplicity, versatility and environmental friendliness, the in situ (Pickering) emulsion polymerization has been demonstrated to be a powerful approach for the large-scale preparation of hybrid latex particles. In this review, the strategies and applications of in situ (Pickering) emulsion polymerization for the preparation of hybrid latex particles are systematically summarized. A particular focus is placed on the strategies for the preparation of hybrid latex particles with enhanced properties and well-defined core-shell, yolk-shell, multinuclear, raspberry-like, dumbbell-shaped, multipod-like or armored morphologies. We hope that the considerable advances, examples and principles presented in this review can motivate future contributions to provide a deeper understanding of current preparation technologies, develop new processes, and enable further exploitation of hybrid latex particles with outstanding characteristics and properties.

Sterically Stabilized Diblock Copolymer Nanoparticles Enable Efficient Preparation of Non-Aqueous Pickering Nanoemulsions

We report the first example of a non-aqueous Pickering nanoemulsion, which comprises glycerol droplets dispersed in mineral oil. The droplet phase is stabilized by hydrophobic sterically stabilized poly(lauryl methacrylate)-poly(benzyl methacrylate) nanoparticles which are prepared directly in mineral oil using polymerization-induced self-assembly. First, a glycerol-in-mineral oil Pickering macroemulsion with a mean droplet diameter of 2.1 ± 0.9 μm is prepared via high-shear homogenization using excess nanoparticles as an emulsifier. Then, this precursor macroemulsion is subjected to high-pressure microfluidization (a single pass at an applied pressure of 20,000 psi) to produce glycerol droplets of approximately 200-250 nm diameter. Transmission electron microscopy studies indicate preservation of the distinctive superstructure produced by nanoparticle adsorption at the glycerol/mineral oil interface, thus confirming the Pickering nature of the nanoemulsion. Glycerol is sparingly soluble in mineral oil, thus such nanoemulsions are rather susceptible to destabilization via Ostwald ripening. Indeed, substantial droplet growth occurs within 24 h at 20 °C, as judged by dynamic light scattering. However, this problem can be suppressed by dissolving a non-volatile solute (sodium iodide) in glycerol prior to formation of the nanoemulsion. This reduces diffusional loss of glycerol molecules from the droplets, with analytical centrifugation studies indicating much better long-term stability for such Pickering nanoemulsions (up to 21 weeks). Finally, the addition of just 5% water to the glycerol phase prior to emulsification enables the refractive index of the droplet phase to be matched to that of the continuous phase, leading to relatively transparent nanoemulsions.

Silica-Coated Micrometer-Sized Latex Particles

A series of silica-coated micrometer-sized poly(methyl methacrylate) latex particles are prepared using a Stöber silica deposition protocol that employs tetraethyl orthosilicate (TEOS) as a soluble silica precursor. Given the relatively low specific surface area of the latex particles, silica deposition is best conducted at relatively high solids to ensure a sufficiently high surface area. Such conditions aid process intensification. Importantly, physical adsorption of chitosan onto the latex particles prior to silica deposition minimizes secondary nucleation and promotes the formation of silica shells: in the absence of chitosan, well-defined silica overlayers cannot be obtained. Thermogravimetry studies indicate that silica formation is complete within a few hours at 20 °C regardless of the presence or absence of chitosan. Kinetic data obtained using this technique suggest that the adsorbed chitosan chains promote surface deposition of silica onto the latex particles but do not catalyze its formation. Systematic variation of the TEOS/latex mass ratio enables the mean silica shell thickness to be tuned from 45 to 144 nm. Scanning electron microscopy (SEM) studies of silica-coated latex particles after calcination at 400 °C confirm the presence of hollow silica particles, which indicates the formation of relatively smooth (albeit brittle) silica shells under optimized conditions. Aqueous electrophoresis and X-ray photoelectron spectroscopy studies are also consistent with latex particles coated in a uniform silica overlayer. The silica deposition formulation reported herein is expected to be a useful generic strategy for the efficient coating of micrometer-sized particles at relatively high solids.

Assembly of partially covered strawberry supracolloids in dilute and concentrate aqueous dispersions

HYPOTHESIS

Core-corona supracolloids can be assembled in aqueous dispersions by controlling the physical interactions between the corona and core colloidal particles. A raspberry corona configuration with full surface coverage of the core can be reached by inducing strong attractive interactions between the individual particles. A controlled partial surface coverage of the core, i.e. strawberry configuration, is however, more difficult to achieve. Supracolloids with different surface coverage ratio exhibit unique and multifunctional surface properties.

EXPERIMENTS

By counterbalancing the multiple physical interactions playing a role during the assembly, the configuration and stability of the assemblies could be fine-tuned over a wide range of concentrations. Supracolloids consisting of polyethylene glycol (PEO)-grafted polymer particles covered by silica nanoparticles were assembled with different configurations, by adjusting the pH and ionic strength of the dispersion, the PEO grafting density and the particles concentration. The self-assembly process and resulting configurations were monitored via cryogenic transmission electron microscopy (Cryo-TEM) and light scattering.

FINDINGS

The suitable conditions to assemble supracolloids with partial corona coverage have been established. Stable strawberry supracolloids could be prepared, both for diluted (1 wt%) and concentrated (12 wt%) dispersions. These hybrid supracolloids with well-defined configuration are highly relevant to developing advanced water-borne paints and inks, food dispersions, cosmetic and healthcare products.

Physical Adsorption of Graphene Oxide onto Polymer Latexes and Characterization of the Resulting Nanocomposite Particles

Polymer/graphene oxide (GO) nanocomposite particles were prepared via heteroflocculation between 140-220 nm cationic latex nanoparticles and anionic GO nanosheets in either acidic or basic conditions. It is demonstrated that nanocomposite particles can be formed using either poly(2-vinylpyridine)-b-poly(benzyl methacrylate) (P2VP-PBzMA) block copolymer nanoparticles prepared by reversible-addition chain-transfer (RAFT)-mediated polymerization-induced self-assembly (PISA), or poly(ethylene glycol)methacrylate (PEGMA)-stabilized P2VP latexes prepared by traditional emulsion polymerization. These two latexes are different morphologically as the P2VP-PBzMA block copolymer latexes have P2VP steric stabilizer chains in their corona, whereas the PEGMA-stabilized P2VP particles have a P2VP core and a nonionic steric stabilizer. Nevertheless, both the P2VP-PBzMA and PEGMA-stabilized P2VP latexes are cationic at low pH. Thus, the addition of GO to these latexes causes flocculation to occur immediately due to the opposite charges between the anionic GO nanosheets and cationic latexes. Control heteroflocculation experiments were conducted using anionic sterically stabilized poly(potassium 3-sulfopropyl methacrylate)-b-poly(benzyl methacrylate) (PKSPMA-PBzMA) and nonionic poly(benzyl methacrylate) (PBzMA) nanoparticles to demonstrate that polymer/GO nanocomposite particles were not formed. The degree of flocculation and the strength of electrostatic interaction between the cationic polymer latexes and GO were assessed using disc centrifuge photosedimentometry (DCP), transmission electron microscopy (TEM), and UV-visible spectrophotometry. These studies suggest that the optimal conditions for the formation of polymer/GO nanocomposite particles were GO contents between 10% and 20% w/w relative to latex, with the latexes containing P2VP in their corona having a stronger electrostatic attraction to the GO sheets.

Pyridine-functional diblock copolymer nanoparticles synthesized via RAFT-mediated polymerization-induced self-assembly: effect of solution pH

Polymerization-induced self-assembly (PISA) via reversible addition-fragmentation chain transfer (RAFT) polymerization has become widely recognized as a versatile and efficient strategy to prepare complex block copolymer nanoparticles with controlled morphology, size, and surface functionality. In this article, we report the preparation of cationic sterically-stabilized poly(2-vinylpyridine)-poly(benzyl methacrylate) (P2VP-PBzMA) diblock copolymer nanoparticles via RAFT-mediated PISA under aqueous emulsion polymerization conditions. It is demonstrated that the solution pH during PISA has a dramatic effect on the resulting P2VP-PBzMA nanoparticles, as judged by dynamic light scattering (DLS), disc centrifuge photosedimentometry (DCP) and transmission electron microscopy (TEM). Varying the solution pH results in the P2VP stabilizer having different solubilities due to protonation/deprotonation of the pyridine groups. This allows P2VP-PBzMA nanoparticles with tunable diameters to be prepared by altering the DP of the stabilizer (P2VP) and/or core-forming block (PBzMA), or simply by changing the solution pH for a fixed copolymer composition. For example, P2VP-PBzMA nanoparticles with larger diameters can be obtained at higher solution pH as the protonation degree of the P2VP stabilizer has a large effect on both the aggregation of polymer chains during the PISA process, and the resulting behavior of the diblock copolymer nanoparticles. Changing the dispersion pH post-polymerization has a relatively limited effect on particle diameter. Furthermore, aqueous electrophoresis studies indicate that these P2VP-PBzMA nanoparticles had good colloidal stability and high cationic charge (>30 mV) below pH 5 and can be dispersed readily over a wide pH range.

Aldehyde-Functional Diblock Copolymer Nano-objects via RAFT Aqueous Dispersion Polymerization

We report the rational design of aldehyde-functional sterically stabilized diblock copolymer nano-objects in aqueous solution via polymerization-induced self-assembly. More specifically, reversible addition-fragmentation chain transfer aqueous dispersion polymerization of 2-hydroxypropyl methacrylate is conducted using a water-soluble precursor block in which every methacrylic repeat unit contains a pendent oligo(ethylene glycol) side chain capped with a cis-diol unit. Systematic variation of the reaction conditions enables the construction of a pseudo-phase diagram, which ensures the reproducible targeting of pure spheres, worms, or vesicles. Selective oxidation of the pendent cis-diol groups using aqueous sodium periodate under mild conditions introduces geminal diols (i.e., the hydrated form of an aldehyde obtained in the presence of water) into the steric stabilizer chains without loss of colloidal stability. In the case of diblock copolymer vesicles, such derivatization leads to the formation of a worm population, indicating partial loss of the original morphology. However, this problem can be circumvented by cross-linking the membrane-forming block prior to periodate oxidation. Moreover, such covalently stabilized aldehyde-functionalized vesicles can be subsequently reacted with either glycine or histidine in aqueous solution, followed by reductive amination to prevent hydrolysis of the labile imine bond. ζ potential measurements confirm that this derivatization significantly affects the electrophoretic behavior of these vesicles. Similarly, the membrane-crosslinked aldehyde-functionalized vesicles can be reacted with a model globular protein, bovine serum albumin, to produce "stealthy" protein-decorated vesicles.

In situ small-angle X-ray scattering studies during the formation of polymer/silica nanocomposite particles in aqueous solution

This study is focused on the formation of polymer/silica nanocomposite particles prepared by the surfactant-free aqueous emulsion polymerization of 2,2,2-trifluoroethyl methacrylate (TFEMA) in the presence of 19 nm glycerol-functionalized aqueous silica nanoparticles using a cationic azo initiator at 60 °C. The TFEMA polymerization kinetics are monitored using 1H NMR spectroscopy, while postmortem TEM analysis confirms that the final nanocomposite particles possess a well-defined core-shell morphology. Time-resolved small-angle X-ray scattering (SAXS) is used in conjunction with a stirrable reaction cell to monitor the evolution of the nanocomposite particle diameter, mean silica shell thickness, mean number of silica nanoparticles within the shell, silica aggregation efficiency and packing density during the TFEMA polymerization. Nucleation occurs after 10-15 min and the nascent particles quickly become swollen with TFEMA monomer, which leads to a relatively fast rate of polymerization. Additional surface area is created as these initial particles grow and anionic silica nanoparticles adsorb at the particle surface to maintain a relatively high surface coverage and hence ensure colloidal stability. At high TFEMA conversion, a contiguous silica shell is formed and essentially no further adsorption of silica nanoparticles occurs. A population balance model is introduced into the SAXS model to account for the gradual incorporation of the silica nanoparticles within the nanocomposite particles. The final PTFEMA/silica nanocomposite particles are obtained at 96% TFEMA conversion after 140 min, have a volume-average diameter of 216 ± 9 nm and contain approximately 274 silica nanoparticles within their outer shells; a silica aggregation efficiency of 75% can be achieved for such formulations.

Inter-droplet force between magnetically polarizable Pickering oil-in-water nanoemulsions stabilized with γ-Al2O3 nanoparticles: Role of electrostatic and electric dipolar interactions

HYPOTHESIS

The presence of nanoparticles at oil-water interface influences the interaction forces between Pickering emulsions. When charged nanoparticles are at the oil-water interface of an electrostatically stabilized emulsion, in addition to the screened Coulombic interaction, electric dipolar force also influences the total inter-droplet force profiles. An in-depth understanding of the effects of such electric dipolar forces is essential for designing colloidally stable Pickering nanoemulsions for various applications.

EXPERIMENTS

Inter-droplet forces between γ-Al₂O₃ nanoparticle stabilized oil-in-water nanoemulsion, containing superparamagnetic nanoparticles (magnetically polarizable) in the oil phase, are measured using the magnetic-chaining technique at different pH and salt concentrations. The role of mono-, di- and tri-valent salts on the inter-droplet force profiles are assessed.

FINDINGS

Force measurement studies reveal a lowering of inter-droplet spacing, within the linear chains, for higher salt concentrations due to an increased screening. Strong interfacial attachment of the charged nanoparticles results in the formation of an asymmetric charge cloud leading to an electric dipolar interaction. Incorporating the contributions of electric dipolar and screened Coulombic interactions, the theoretically estimated total repulsive force magnitudes are in good agreement with the experimental data. The obtained results offer better insights into the nature of colloidal force between charged particle stabilized nanoemulsions.

Block Copolymer Nanoparticles are Effective Dispersants for Micrometer-Sized Organic Crystalline Particles

Well-defined sterically stabilized diblock copolymer nanoparticles of 29 nm diameter are prepared by RAFT aqueous emulsion polymerization of methyl methacrylate using a dithiobenzoate-capped poly(glycerol monomethacrylate) precursor. These nanoparticles are evaluated as a dispersant for the preparation of organic crystalline microparticles via ball milling. This is exemplified for azoxystrobin, which is a broad-spectrum fungicide that is widely used to protect various food crops. Laser diffraction and optical microscopy studies indicate the formation of azoxystrobin microparticles of approximately 2 μm diameter after ball milling for 10 min at 400 rpm. Nanoparticle adsorption at the surface of these azoxystrobin microparticles is confirmed by electron microscopy studies. The extent of nanoparticle adsorption on the azoxystrobin microparticles can be quantified using a supernatant assay based on solution densitometry. This technique indicates an adsorbed amount of approximately 5.5 mg m-2, which is sufficient to significantly reduce the negative zeta potential exhibited by azoxystrobin. Moreover, this adsorbed amount appears to be essentially independent of the nature of the core-forming block, with similar data being obtained for both poly(methyl methacrylate)- and poly(2,2,2-trifluoroethyl methacrylate)-based nanoparticles. Finally, X-ray photoelectron spectroscopy studies confirm attenuation of the underlying N1s signal arising from the azoxystrobin microparticles by the former adsorbed nanoparticles, suggesting a fractional surface coverage of approximately 0.24. This value is consistent with a theoretical surface coverage of 0.25 calculated from the adsorption isotherm data. Overall, this study suggests that sterically stabilized diblock copolymer nanoparticles may offer a useful alternative approach to traditional soluble copolymer dispersants for the preparation of suspension concentrates affecting the context of agrochemical applications.

Effect of Salt on the Formation and Stability of Water-in-Oil Pickering Nanoemulsions Stabilized by Diblock Copolymer Nanoparticles

Sterically stabilized diblock copolymer nanoparticles are prepared in n-dodecane using polymerization-induced self-assembly. Precursor Pickering macroemulsions are then prepared by the addition of water followed by high-shear homogenization. In the absence of any salt, high-pressure microfluidization of such precursor emulsions leads to the formation of relatively large aqueous droplets with DLS measurements indicating a mean diameter of more than 600 nm. However, systemically increasing the salt concentration produces significantly finer droplets after microfluidization, until a limiting diameter of around 250 nm is obtained at 0.11 M NaCl. The mean size of these aqueous droplets can also be tuned by systematically varying the nanoparticle concentration, applied pressure, and the number of passes through the microfluidizer. The mean number of nanoparticles adsorbed onto each aqueous droplet and their packing efficiency are calculated. SAXS studies conducted on a Pickering nanoemulsion prepared using 0.11 M NaCl confirms that the aqueous droplets are coated with a loosely packed monolayer of nanoparticles. The effect of varying the NaCl concentration within the droplets on their initial rate of Ostwald ripening is investigated using DLS. Finally, the long-term stability of these water-in-oil Pickering nanoemulsions is assessed using analytical centrifugation. The rate of droplet ripening can be substantially reduced by using 0.11 M NaCl instead of pure water. However, increasing the salt concentration up to 0.43 M provided no further improvement in the long-term stability of such nanoemulsions.

Multicompartment emulsion droplets for programmed release of hydrophobic cargoes

Delivery systems with multicompartmental structures that allow simultaneous delivery of several cargos are of great interest in both fundamental research and industrial applications. Here, we report a facile and easily scalable approach to fabricate multi-compartmentalized microdroplets for achieving programmed release of hydrophobic cargoes. Well-dispersed nanodroplets stabilized by natural Quillaja saponin served as an effective colloid stabilizer for fabricating microscale emulsion droplets with multicompartment architectures comprising many nanoscale droplets as a shell and single microscale core. Control of the number of nanodroplets allows accurate manipulation of the interface permeability for flexible and controllable release of volatile compounds (e.g., 2,3-butanedione, cis-3-hexen-1-ol, ethyl butyrate, d-limonene). More interestingly, the multicompartment microdroplets exhibited a higher flexibility for programmed release of different volatile compounds, as well as curcumin, during in vitro digestion by introducing cargos into the shell subcompartments or core microcompartment. The promising results highlight the power of this multi-compartmentalized system toward accessing a powerful platform for functional cargo delivery strategies.

Segmental Mobility Studies of Poly(N-isopropyl acrylamide) Interactions with Gold Nanoparticles and Its Use as a Thermally Driven Trapping System

Thermal desolvation of poly(N-isopropylacrylamide) (PNIPAM) in the presence of a low concentration of gold nanoparticles incorporates the nanoparticles resulting in suspended aggregates. By covalently incorporating <1% acenaphthylene into the polymerization feed this copolymer is enabled to be used as a model to study the segmental mobility of the PNIPAM backbone in response to gold nanoparticles both below and above the desolvation temperature, showing that there is a physical conformational rearrangement of the soluble polymer at ultralow nanoparticle loadings, indicating low affinity interactions with the nanoparticles. Thermal desolvation is capable of extracting >99.9% of the nanoparticles from their solutions and hence demonstrates that poly(N-isopropylacrylamide) can act as an excellent scrubbing system to remove metallic nanomaterial pollutants from solution.

Bespoke Diblock Copolymer Nanoparticles Enable the Production of Relatively Stable Oil-in-Water Pickering Nanoemulsions

Sterically stabilized diblock copolymer nanoparticles with an intensity-average diameter of 25 nm are prepared in the form of a concentrated aqueous dispersion using polymerization-induced self-assembly (PISA). The addition of n-dodecane followed by high-shear homogenization produces n-dodecane-in-water Pickering macroemulsions of 22-46 μm diameter. If the nanoparticles are present in sufficient excess, then subsequent processing using a high-pressure microfluidizer leads to the formation of Pickering nanoemulsions with a mean oil droplet diameter below 200 nm. The size of these Pickering nanoemulsions can be tuned by systematically varying the nanoparticle concentration, applied pressure, number of passes, and oil volume fraction. High-internal-phase emulsions can also be achieved by increasing the n-dodecane volume fraction up to 0.80. TEM studies of (dried) n-dodecane droplets confirm the presence of intact nanoparticles and suggest a relatively high surface coverage, which is consistent with model packing calculations based on radius ratios. Such Pickering nanoemulsions proved to be surprisingly stable with respect to Ostwald ripening, with no significant change in the mean DLS droplet diameter after storage for approximately 4 months at 20 °C.

Microstructure and Elastic Properties of Colloidal Gel Foams

Colloidal gel foams are composed of a continuous, attractive particle network that surrounds and interconnects dispersed bubbles. Here, we investigate their stability, morphology, and elasticity as a function of foaming intensity, surfactant concentration and hydrophobicity, pH, and colloid volume fraction. Upon optimizing these parameters, highly stable colloidal gel foams are created. Within this stability region, the specific interfacial area between the continuous (colloidal gel) and dispersed (bubble) phase can be varied over 2 orders of magnitude leading to a concomitant increase in storage modulus, which scales nearly linearly with specific interfacial area. Our observations provide design guidelines for attractive-particle stabilized foams that enable the programmable assembly of architected porous materials.

Depletion-Induced Encapsulation by Dumbbell-Shaped Patchy Colloids Stabilize Microspheres against Aggregation

In this paper, we demonstrate the stabilization of polystyrene microspheres by encapsulating them with dumbbell-shaped colloids with a sticky and a nonsticky lobe. Upon adding a depletant, an effective short ranged attraction is induced between the microspheres and the smaller, smooth lobes of the dumbbells, making those specifically sticky, whereas the interaction with the larger lobes of the dumbbells is considerably less attractive due to their rough surface, which reduces the overlap volume and leaves them nonsticky. The encapsulation of the microspheres by these rough-smooth patchy dumbbells is investigated using a combination of experiments and computer simulations, both resulting in partial coverage of the template particles. For larger microspheres, the depletion attraction is stronger, resulting in a larger fraction of dumbbells that are attached with both lobes to the surface of microspheres. We thus find a template curvature dependent orientation of the dumbbells. In the Monte Carlo simulations, the introduction of such a small, curvature dependent attraction between the rough lobes of the dumbbells resulted in an increased coverage. However, kinetic constraints imposed by the dumbbell geometry seem to prevent optimal packing of the dumbbells on the template particles under all investigated conditions in experiments and simulations. Despite the incomplete coverage, the encapsulation by dumbbell particles does prevent aggregation of the microspheres, thus acting as a colloid-sized steric stabilizer.

Adsorption of Silica Nanoparticles onto Poly(N-vinylpyrrolidone)-Functionalized Polystyrene Latex

This paper presents a more general method to prepare silica-coated polystyrene (PS) particles with minimal excess silica by adsorption, highlighting the role of poly(N-vinylpyrrolidone) (PVP). The method is based on the addition of small silica nanoparticles onto submicrometer-sized near-monodisperse polymer latex particles under the conditions of monolayer silica coverage of the latex surface. Either a cationic or an anionic initiator could be used in the PVP-involved emulsion polymerization to prepare PS particles, and the adsorption was conducted successfully either under acidic or basic conditions. Neither a cationic initiator nor a basic condition is a prerequisite for the adsorption process, which should be related to the much stronger interaction between PVP and the silica surface. This method is expected to substantially extend the adsorption conditions of polymer-silica colloidal nanocomposite syntheses.

Adsorption of Small Cationic Nanoparticles onto Large Anionic Particles from Aqueous Solution: A Model System for Understanding Pigment Dispersion and the Problem of Effective Particle Density

The present study focuses on the use of copolymer nanoparticles as a dispersant for a model pigment (silica). Reversible addition-fragmentation chain transfer (RAFT) alcoholic dispersion polymerization was used to synthesize sterically stabilized diblock copolymer nanoparticles. The steric stabilizer block was poly(2-(dimethylamino)ethyl methacrylate) (PDMA) and the core-forming block was poly(benzyl methacrylate) (PBzMA). The mean degrees of polymerization for the PDMA and PBzMA blocks were 71 and 100, respectively. Transmission electron microscopy (TEM) studies confirmed a near-monodisperse spherical morphology, while dynamic light scattering (DLS) studies indicated an intensity-average diameter of 30 nm. Small-angle X-ray scattering (SAXS) reported a volume-average diameter of 29 ± 0.5 nm and a mean aggregation number of 154. Aqueous electrophoresis measurements confirmed that these PDMA71-PBzMA100 nanoparticles acquired cationic character when transferred from ethanol to water as a result of protonation of the weakly basic PDMA chains. Electrostatic adsorption of these nanoparticles from aqueous solution onto 470 nm silica particles led to either flocculation at submonolayer coverage or steric stabilization at or above monolayer coverage, as judged by DLS. This technique indicated that saturation coverage was achieved on addition of approximately 465 copolymer nanoparticles per silica particle, which corresponds to a fractional surface coverage of around 0.42. These adsorption data were corroborated using thermogravimetry, UV spectroscopy and X-ray photoelectron spectroscopy. TEM studies indicated that the cationic nanoparticles remained intact on the silica surface after electrostatic adsorption, while aqueous electrophoresis confirmed that surface charge reversal occurred below pH 7. The relatively thick layer of adsorbed nanoparticles led to a significant reduction in the effective particle density of the silica particles from 1.99 g cm-3 to approximately 1.74 g cm-3, as judged by disk centrifuge photosedimentometry (DCP). Combining the DCP and SAXS data suggests that essentially no deformation of the PBzMA cores occurs during nanoparticle adsorption onto the silica particles.

One-pot formation of monodisperse polymer@SiO2 core–shell nanoparticles via surfactant-free emulsion polymerization using an adaptive silica precursor polymer

Monodisperse PMMA@SiO₂ core–shell nanoparticles are formed via a new type of surfactant-free emulsion polymerization using polyethoxysiloxane as a silica precursor.

Vermicious thermo-responsive Pickering emulsifiers

Thermo-responsive vermicious (or worm-like) diblock copolymer nanoparticles prepared directly in n-dodecane are used to stabilise water-in-oil Pickering emulsions.

Thermo-responsive vermicious (or worm-like) diblock copolymer nanoparticles prepared directly in n-dodecane via polymerisation-induced self-assembly (PISA) were used to stabilise water-in-oil Pickering emulsions. Mean droplet diameters could be tuned from 8 to 117 μm by varying the worm copolymer concentration and the water volume fraction and very high worm adsorption efficiencies (∼100%) could be obtained below a certain critical copolymer concentration (∼0.50%). Heating a worm dispersion up to 150 °C led to a worm-to-sphere transition, which proved to be irreversible if conducted at sufficiently low copolymer concentration. This affords a rare opportunity to directly compare the Pickering emulsifier performance of chemically identical worms and spheres. It is found that the former nanoparticles are markedly more efficient, since worm-stabilised water droplets are always smaller than the equivalent sphere-stabilised droplets prepared under identical conditions. Moreover, the latter emulsions are appreciably flocculated, whereas the former emulsions proved to be stable. SAXS studies indicate that the mean thickness of the adsorbed worm layer surrounding the water droplets is comparable to that of the worm cross-section diameter determined for non-adsorbed worms dispersed in the continuous phase. Thus the adsorbed worms form a monolayer shell around the water droplets, rather than ill-defined multilayers. Under certain conditions, demulsification occurs on heating as a result of a partial worm-to-sphere morphological transition.

Are block copolymer worms more effective Pickering emulsifiers than block copolymer spheres?

RAFT-mediated polymerisation-induced self-assembly (PISA) is used to prepare six types of amphiphilic block copolymer nanoparticles which were subsequently evaluated as putative Pickering emulsifiers for the stabilisation of n-dodecane-in-water emulsions. It was found that linear poly(glycerol monomethacrylate)-poly(2-hydroxypropyl methacrylate) (PGMA-PHPMA) diblock copolymer spheres and worms do not survive the high shear homogenisation conditions used for emulsification. Stable emulsions are obtained, but the copolymer acts as a polymeric surfactant; individual chains rather than particles are adsorbed at the oil-water interface. Particle dissociation during emulsification is attributed to the weakly hydrophobic character of the PHPMA block. Covalent stabilisation of these copolymer spheres or worms can be readily achieved by addition of ethylene glycol dimethacrylate (EGDMA) during the PISA synthesis. TEM studies confirm that the resulting cross-linked spherical or worm-like nanoparticles survive emulsification and produce genuine Pickering emulsions. Alternatively, stabilisation can be achieved by either replacing or supplementing the PHPMA block with the more hydrophobic poly(benzyl methacrylate) (PBzMA). The resulting linear spheres or worms also survive emulsification and produce stable n-dodecane-in-water Pickering emulsions. The intrinsic advantages of anisotropic worms over isotropic spheres for the preparation of Pickering emulsions are highlighted. The former particles are more strongly adsorbed at similar efficiencies compared to spheres and also enable smaller oil droplets to be produced for a given copolymer concentration. The scalable nature of PISA formulations augurs well for potential applications of anisotropic block copolymer nanoparticles as Pickering emulsifiers.

Physical adsorption of anisotropic titania nanoparticles onto poly(2-vinylpyridine) latex and characterisation of the resulting nanocomposite particles

Four poly(2-vinylpyridine) latexes with intensity-average mean diameters ranging between 246 and 955nm were prepared by aqueous emulsion polymerisation. These latexes were characterised by transmission electron microscopy, field emission scanning electron microscopy, dynamic light scattering, aqueous electrophoresis, disc centrifuge photosedimentometry and thermogravimetry. The adsorption of rice grain-shaped nano-sized titania particles onto the surface of these latex particles from aqueous solution was investigated. It was found that the titania particles adsorb strongly at pH 10 and the optimal loading and packing density of titania was investigated for each latex. The resulting core-shell P2VP-titania nanocomposite particles were characterised in terms of their titania contents, surface coverages and colloidal stabilities. UV-Vis spectra were recorded for the titania nanoparticles, the original P2VP latexes and the poly(2-vinylpyridine)-titania nanocomposite particles. It was found that, for the larger nanocomposite particles, UV-Vis absorption was dominated by the latex core, whereas the smaller P2VP-titania nanocomposite particles exhibited UV attenuation to longer wavelengths compared to both the bare latex and the titania particles. The poly(2-vinylpyridine) cores were selectively removed by calcination of the nanocomposite particles and the resulting hollow titania structures were investigated by transmission electron microscopy.

Comparison of pseudo-living character of RAFT polymerizations conducted under homogeneous and heterogeneous conditions

Evidence is presented for (i) the greater pseudo-living character of RAFT dispersion polymerization compared to the equivalent solution polymerization and (ii) the presence of monomer-swollen micelles in the former formulation.

Direct observation of giant Pickering emulsion and colloidosome droplet interaction and stability

The interactions of two 2-mm pendant oil droplets grown in the presence of an aqueous solution of poly(glycerol monomethacrylate)-stabilized polystyrene latex particles was observed using a high-speed video camera. The coalescence behavior was monitored as a function of oil type (n-dodecane versus sunflower oil) and particle size (135 versus 902 nm), as well as in the presence and absence of an oil-soluble cross-linker [tolylene 2,4-diisocyanate-terminated poly(propylene glycol)]. The damping coefficient of the coalescing n-dodecane droplets was found to increase in the presence of the latex, demonstrating particle adsorption. Coalescence times increased when the oil phase was changed from n-dodecane to sunflower oil, because of the much higher viscosity of the latter oil. In addition, increasing the adsorbed particle size from 135 to 902 nm led to longer coalescence times because of the greater distance separating the oil droplets. Coalescence times observed in the presence of the larger 902-nm particles indicated that two different modes of contact can occur prior to a coalescence event (bilayer or bridging monolayer of particles in the film). Addition of an oil-soluble surface-active cross-linker to the sunflower oil phase to react with the hydroxy groups of the particle stabilizer reduced the interfacial elasticity and ultimately prevented coalescence after cross-linking for 20 min at 25 °C. Such giant colloidosomes can remain in contact for several hours without undergoing coalescence, which demonstrates their high stability. Furthermore, coalescence is prevented even if the cross-linker is present in only one of the pendant droplets. Finally, evidence for cross-linker diffusion from one pendant droplet to another was indicated by a visible filament connecting the two droplets upon retraction.

Heterocoagulation as a facile route to prepare stable serum albumin-nanoparticle conjugates for biomedical applications: synthetic protocols and mechanistic insights

There is increasing interest in using serum albumin, the most abundant plasma protein, as a stabilizing agent in the context of nanomedicine. Using poly(vinyl amine)-stabilized polypyrrole nanoparticles as an example, we report a facile generic route to prepare serum albumin-nanoparticle conjugates via heterocoagulation. Time-resolved dynamic light scattering (DLS), disk centrifuge photosedimentometry (DCP), and circular dichroism (CD) spectroscopy studies confirm that bovine serum albumin (BSA) adsorbs rapidly onto the cationic poly(vinyl amine)-stabilized polypyrrole nanoparticles and suggest that the initial well-defined protein coronal is subsequently cross-linked via thiol-disulfide exchange. These BSA-nanoparticle conjugates were further characterized by X-ray photoelectron spectroscopy (XPS), aqueous electrophoresis, field emission scanning electron microscopy (FE SEM), and transmission electron microscopy (TEM). They exhibit excellent long-term colloidal stability under physiological conditions without further purification, suggesting strong irreversible adsorption by the BSA. Protein adsorption appears to be co-operative and both thermodynamic and mechanistic aspects were examined via aqueous electrophoresis, DCP, and DLS studies.

Colloid thermodynamic effect as the universal driving force for fabricating various functional composite particles

The design and fabrication of functional nanocomposites is an active area of research because composite particles have significantly improved physical and chemical properties over those of their single-component counterparts. Traditionally, chemical pretreatments of the components were used to enhance their physicochemical or chemical interactions. Here, we propose a novel approach to taking advantage of the beauty of thermodynamics. A series of functional materials, including graphene nanosheets, carbon nanotubes, noble metals, magnetic materials, conducting polymers, attapulgite, and etc. were incorporated with polystyrene particles by a thermodynamic driving force. This unique approach is facile and versatile and shows the considerable significance of developments in both scientific methodology and particle engineering.

Efficient synthesis of sterically-stabilized nano-objects via RAFT dispersion polymerization of benzyl methacrylate in alcoholic media

Synthesis of diblock copolymer nano-objects: alcohol is a good idea! RAFT dispersion polymerization of benzyl methacrylate in alcohol using weak polyelectrolyte-based chain transfer agents allows the facile synthesis of sterically stabilized diblock copolymer nano-objects with very high monomer conversions. Such syntheses are usually problematic when conducted in water due to electrostatic repulsion between highly charged stabilizer chains, which impedes in situ self-assembly. Construction of a detailed phase diagram facilitates reproducible syntheses of well-defined diblock copolymer spheres, worms or vesicles, since it allows mixed phase regions to be avoided. Aqueous electrophoresis studies confirm that these nano-objects can acquire substantial surface charge when transferred to aqueous solution due to ionization (or protonation) of the polyacid (or polybase) stabilizer chains.

Correcting for a density distribution: particle size analysis of core-shell nanocomposite particles using disk centrifuge photosedimentometry

Many types of colloidal particles possess a core-shell morphology. In this Article, we show that, if the core and shell densities differ, this morphology leads to an inherent density distribution for particles of finite polydispersity. If the shell is denser than the core, this density distribution implies an artificial narrowing of the particle size distribution as determined by disk centrifuge photosedimentometry (DCP). In the specific case of polystyrene/silica nanocomposite particles, which consist of a polystyrene core coated with a monolayer shell of silica nanoparticles, we demonstrate that the particle density distribution can be determined by analytical ultracentrifugation and introduce a mathematical method to account for this density distribution by reanalyzing the raw DCP data. Using the mean silica packing density calculated from small-angle X-ray scattering, the real particle density can be calculated for each data point. The corrected DCP particle size distribution is both broader and more consistent with particle size distributions reported for the same polystyrene/silica nanocomposite sample using other sizing techniques, such as electron microscopy, laser light diffraction, and dynamic light scattering. Artifactual narrowing of the size distribution is also likely to occur for many other polymer/inorganic nanocomposite particles comprising a low-density core of variable dimensions coated with a high-density shell of constant thickness, or for core-shell latexes where the shell is continuous rather than particulate in nature.

Efficient synthesis of poly(2-hydroxypropyl methacrylate)-silica colloidal nanocomposite particles via aqueous dispersion polymerization

Colloidally stable poly(2-hydroxypropyl methacrylate)-silica nanocomposite particles can be efficiently prepared by aqueous dispersion polymerization at 60 °C using a binary mixture of an ultrafine aqueous silica sol and poly(N-vinylpyrrolidone) [PVP] as the stabilizer system.

All-acrylic film-forming colloidal polymer/silica nanocomposite particles prepared by aqueous emulsion polymerization

The efficient synthesis of all-acrylic, film-forming, core-shell colloidal nanocomposite particles via in situ aqueous emulsion copolymerization of methyl methacrylate with n-butyl acrylate in the presence of a glycerol-functionalized ultrafine silica sol using a cationic azo initiator at 60 °C is reported. It is shown that relatively monodisperse nanocomposite particles can be produced with typical mean weight-average diameters of 140-330 nm and silica contents of up to 39 wt %. The importance of surface functionalization of the silica sol is highlighted, and it is demonstrated that systematic variation of parameters such as the initial silica sol concentration and initiator concentration affect both the mean particle diameter and the silica aggregation efficiency. The nanocomposite morphology comprises a copolymer core and a particulate silica shell, as determined by aqueous electrophoresis, X-ray photoelectron spectroscopy, and electron microscopy. Moreover, it is shown that films cast from n-butyl acrylate-rich copolymer/silica nanocomposite dispersions are significantly more transparent than those prepared from the poly(styrene-co-n-butyl acrylate)/silica nanocomposite particles reported previously. In the case of the aqueous emulsion homopolymerization of methyl methacrylate in the presence of ultrafine silica, a particle formation mechanism is proposed to account for the various experimental observations made when periodically sampling such nanocomposite syntheses at intermediate comonomer conversions.

Time-resolved small-angle X-ray scattering studies of polymer-silica nanocomposite particles: initial formation and subsequent silica redistribution

Small angle X-ray scattering (SAXS) is a powerful characterization technique for the analysis of polymer-silica nanocomposite particles due to their relatively narrow particle size distributions and high electron density contrast between the polymer core and the silica shell. Time-resolved SAXS is used to follow the kinetics of both nanocomposite particle formation (via silica nanoparticle adsorption onto sterically stabilized poly(2-vinylpyridine) (P2VP) latex in dilute aqueous solution) and also the spontaneous redistribution of silica that occurs when such P2VP-silica nanocomposite particles are challenged by the addition of sterically stabilized P2VP latex. Silica adsorption is complete within a few seconds at 20 °C and the rate of adsorption strongly dependent on the extent of silica surface coverage. Similar very short time scales for silica redistribution are consistent with facile silica exchange occurring as a result of rapid interparticle collisions due to Brownian motion; this interpretation is consistent with a zeroth-order Smoluchowski-type calculation.

Unexpected facile redistribution of adsorbed silica nanoparticles between latexes

Addition of excess sterically stabilized P2VP latex to a colloidal dispersion of P2VP-silica nanocomposite particles (with silica shells at full monolayer coverage) leads to the facile redistribution of the silica nanoparticles such that partial coverage of all the P2VP latex particles is achieved. This silica exchange, which is complete within 1 h at 20 degrees C as judged by small-angle x-ray scattering, is observed for nanocomposite particles prepared by heteroflocculation, but not for nanocomposite particles prepared by in situ copolymerization. These observations are expected to have important implications for the optimization of nanocomposite formulations in the coatings industry.