Frequency-multiplication high-output triboelectric nanogenerator for sustainably powering biomedical microsystems

A noval transparent triboelectric nanogenerator as electronic skin for real-time breath monitoring

Against the backdrop of advancements in modern multifunctional wearable electronics, there is a growing demand for simple, sustainable, and portable electronic skin (e-skin), posing significant challenges. This study aims to delineate the development of a straightforward, transparent, highly sensitive, and high power-density electronic skin based on a triboelectric nanogenerator(S-TENG), designed for harvesting human body energy and real-time monitoring of the physiological motion status. Our e-skin incorporates thermally treated polyvinylidene fluoride (PVDF) fiber membranes as the contact layer and a film of silver nanowires as the conductive electrodes. The resulting contact-separation type e-skin exhibits an impressive transparency of 80 %, along with a nice sensitivity value, capable of detecting a light touch from a 0.13 g sponge and demonstrating good working stability and breathability. Leveraging the triboelectric effect, our e-skin generates an open-circuit voltage of 301 V and a short-circuit current of 2.7 μA under an extrinsic force of 8 N over an interaction area of 4 × 4 cm2, achieving a power density up to 306 mW/m2. With its signal processing circuitry, the integrated S-TENG showcases nice energy harvesting and signal transmission capabilities. Accordingly, we contend that S-TENG has potential applications in energy capture and real-time human motion state monitoring. This research is anticipated to blaze a novel and practical trail for self-powered wearable devices and personalized health rehabilitation training regimens.

Bulk Schottky Junctions-Based Flexible Triboelectric Nanogenerators to Power Backscatter Communications in Green 6G Networks

This work introduces a novel method to construct Schottky junctions to boost the output performance of triboelectric nanogenerators (TENGs). Perovskite barium zirconium titanate (BZT) core/metal silver shell nanoparticles are synthesized to be embedded into electrospun polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) nanofibers before they are used as tribo-negative layers. The output power of TENGs with composite fiber mat exhibited >600% increase compared to that with neat polymer fiber mat. The best TENG achieved 1339 V in open-circuit voltage, 40 µA in short-circuit current and 47.9 W m-2 in power density. The Schottky junctions increased charge carrier density in tribo-layers, ensuring a high charge transfer rate while keeping the content of conductive fillers low, thus avoiding charge loss and improving performance. These TENGs are utilized to power radio frequency identification (RFID) tags for backscatter communication (BackCom) systems, enabling ultra-massive connectivity in the 6G wireless networks and reducing information communications technology systems' carbon footprint. Specifically, TENGs are used to provide an additional energy source to the passive tags. Results show that TENGs can boost power for BackCom and increase the communication range by 386%. This timely contribution offers a novel route for sustainable 6G applications by exploiting the expanded communication range of BackCom tags.

Self-Powered Sensing in Wearable Electronics─A Paradigm Shift Technology

With the advancements in materials science and micro/nanoengineering, the field of wearable electronics has experienced a rapid growth and significantly impacted and transformed various aspects of daily human life. These devices enable individuals to conveniently access health assessments without visiting hospitals and provide continuous, detailed monitoring to create comprehensive health data sets for physicians to analyze and diagnose. Nonetheless, several challenges continue to hinder the practical application of wearable electronics, such as skin compliance, biocompatibility, stability, and power supply. In this review, we address the power supply issue and examine recent innovative self-powered technologies for wearable electronics. Specifically, we explore self-powered sensors and self-powered systems, the two primary strategies employed in this field. The former emphasizes the integration of nanogenerator devices as sensing units, thereby reducing overall system power consumption, while the latter focuses on utilizing nanogenerator devices as power sources to drive the entire sensing system. Finally, we present the future challenges and perspectives for self-powered wearable electronics.

Skin-Contact Triboelectric Nanogenerator for Energy Harvesting and Motion Sensing: Principles, Challenges, and Perspectives

Energy harvesting has become an increasingly important field of research as the demand for portable and wearable devices continues to grow. Skin-contact triboelectric nanogenerator (TENG) technology has emerged as a promising solution for energy harvesting and motion sensing. This review paper provides a detailed overview of skin-contact TENG technology, covering its principles, challenges, and perspectives. The introduction begins by defining skin-contact TENG and explaining the importance of energy harvesting and motion sensing. The principles of skin-contact TENG are explored, including the triboelectric effect and the materials used for energy harvesting. The working mechanism of skin-contact TENG is also discussed. This study then moves onto the applications of skin-contact TENG, focusing on energy harvesting for wearable devices and motion sensing for healthcare monitoring. Furthermore, the integration of skin-contact TENG technology with other technologies is discussed to highlight its versatility. The challenges in skin-contact TENG technology are then highlighted, which include sensitivity to environmental factors, such as humidity and temperature, biocompatibility and safety concerns, and durability and reliability issues. This section of the paper provides a comprehensive evaluation of the technological limitations that must be considered when designing skin-contact TENGs. In the Perspectives and Future Directions section, this review paper highlights various advancements in materials and design, as well as the potential for commercialization. Additionally, the potential impact of skin-contact TENG technology on the energy and healthcare industries is discussed.

High-output soft-contact fiber-structure triboelectric nanogenerator and its sterilization application

Infectious diseases are spreading rapidly with the flow of the world's population, and the prevention of epidemic diseases is particularly important for public and personal health. Therefore, there is an urgent need to develop a simple, efficient and non-toxic method to control the spread of bacteria and viruses. The newly developed triboelectric nanogenerator (TENG) can generate a high voltage, which inhibits bacterial reproduction. However, the output performance is the main factor limiting real-world applications of TENGs. Herein, we report a soft-contact fiber-structure TENG to avoid insufficient friction states and to improve the output, especially at a high rotation speed. Rabbit hair, carbon nanotubes, polyvinylidene difluoride film and paper all contain fiber structures that are used to guarantee soft contact between the friction layers and improve the contact state and abrasion problem. Compared with a direct-contact triboelectric nanogenerator, the outputs of this soft-contact fiber-structure TENG are improved by about 350%. Meanwhile, the open-circuit voltage can be enhanced to 3440 V, which solves the matching problems when driving high-voltage devices. A TENG-driven ultraviolet sterilization system is then developed. The bactericidal rate of this sterilization system can reach 91%, which significantly reduces the risk of disease spread. This work improves a forward-looking strategy to improve the output and service life of the TENG. It also expands the applications of self-powered TENG sterilization systems.

A Self-powered Neural Stimulator Based on Programmable Triboelectric Nanogenerators

Modulation of peripheral nerve is an emerging field for neuroprosthesis and bioelectronic medicine. With the developing neural interfacing technology that directly communicates with peripheral nerves, several powering schemes have been investigated for long-term use of implantable devices such as wireless and conversion of human body energy. But due to the limitations such as energy conversion efficiency and complexity, none of these methods can fully replace the current battery-based neuroprosthetic systems. This study proposes a new scheme based on programmable triboelectric nanogenerators for self-powered neural stimulations. The device can generate current pulses of more than 100 V by slightly shaking the device. The capability of neural stimulation is validated by sciatic nerve stimulation. Furthermore, the shaking frequency can control the measured kicking force of the rat leg. This prototype can be further minimized and optimized for a fully implantable self-powered/wireless neuroprosthetic system.

Unique Contact Point Modification Technique for Boosting the Performance of a Triboelectric Nanogenerator and Its Application in Road Safety Sensing and Detection

A triboelectric nanogenerator (TENG) is a potential technique that can convert waste kinetic energy to electrical energy by contact separation followed by electrostatic induction. Herein, a unique contact point modification technique has been reviewed carefully via the enlargement of the effective surface area of the tribo layer by using a simple and scalable printing method. In this study, the zinc sulfide (ZnS) nanostructure morphology has been introduced directly on an aluminum electrode (Al) as a tribo positive layer by a modified hydrothermal method and different line patterns directly printed on overhead projector (OHP) transparent sheets by a monochrome laser printer as a tribo negative layer to increase the effective contact area and work-function difference between two tribo layers. This dual parameter results in ∼11 times increment in the open-circuit output voltage (∼420 V) and ∼17 times increment in the short-circuit current density (∼83.33 mA m^-2) compared to the normal one. Furthermore, with the proposed surface modification technique, an ultrahigh instantaneous output power density of ∼3.9 W m^-2 at a load resistance of 2 MΩ was easily achieved. The direct energy conversion efficiency reached up to 66.67% at 2 MΩ load, which is very high compared to other traditional TENGs. Further, the fabricated TENG demonstrated efficacy in novel road safety sensing applications in hilly areas to control vehicle movement. Therefore, the current idea of surface engineering using a laser printer will be helpful for energy-harvesting enthusiasts to develop more efficient nanogenerators for higher energy conversions.

Recent Advances in Triboelectric Nanogenerators: From Technological Progress to Commercial Applications

Serious climate changes and energy-related environmental problems are currently critical issues in the world. In order to reduce carbon emissions and save our environment, renewable energy harvesting technologies will serve as a key solution in the near future. Among them, triboelectric nanogenerators (TENGs), which is one of the most promising mechanical energy harvesters by means of contact electrification phenomenon, are explosively developing due to abundant wasting mechanical energy sources and a number of superior advantages in a wide availability and selection of materials, relatively simple device configurations, and low-cost processing. Significant experimental and theoretical efforts have been achieved toward understanding fundamental behaviors and a wide range of demonstrations since its report in 2012. As a result, considerable technological advancement has been exhibited and it advances the timeline of achievement in the proposed roadmap. Now, the technology has reached the stage of prototype development with verification of performance beyond the lab scale environment toward its commercialization. In this review, distinguished authors in the world worked together to summarize the state of the art in theory, materials, devices, systems, circuits, and applications in TENG fields. The great research achievements of researchers in this field around the world over the past decade are expected to play a major role in coming to fruition of unexpectedly accelerated technological advances over the next decade.

Rational Design of Cellulosic Triboelectric Materials for Self-Powered Wearable Electronics

With the rapid development of the Internet of Things and flexible electronic technologies, there is a growing demand for wireless, sustainable, multifunctional, and independently operating self-powered wearable devices. Nevertheless, structural flexibility, long operating time, and wearing comfort have become key requirements for the widespread adoption of wearable electronics. Triboelectric nanogenerators as a distributed energy harvesting technology have great potential for application development in wearable sensing. Compared with rigid electronics, cellulosic self-powered wearable electronics have significant advantages in terms of flexibility, breathability, and functionality. In this paper, the research progress of advanced cellulosic triboelectric materials for self-powered wearable electronics is reviewed. The interfacial characteristics of cellulose are introduced from the top-down, bottom-up, and interfacial characteristics of the composite material preparation process. Meanwhile, the modulation strategies of triboelectric properties of cellulosic triboelectric materials are presented. Furthermore, the design strategies of triboelectric materials such as surface functionalization, interfacial structure design, and vacuum-assisted self-assembly are systematically discussed. In particular, cellulosic self-powered wearable electronics in the fields of human energy harvesting, tactile sensing, health monitoring, human-machine interaction, and intelligent fire warning are outlined in detail. Finally, the current challenges and future development directions of cellulosic triboelectric materials for self-powered wearable electronics are discussed.

Flexible BaTiO3 Thin Film-Based Coupled Nanogenerator for Simultaneously Scavenging Light and Vibration Energies

Ferroelectric materials have a variety of properties, such as piezoelectricity, pyroelectricity, and the ferroelectric photovoltaic effect, which enable them to obtain electrical energy from various external stimuli. Here, we report a coupled nanogenerator based on flexible BTO ferroelectric films with a cantilevered beam structure. It combines the photovoltaic and flexoelectric effects in a ferroelectric materials-based coupled nanogenerator for simultaneously scavenging vibration energy and light energy, thus improving energy scavenging performance. As compared with the photovoltaic effect individually, simultaneous vibration and light illumination under a light intensity of 57 mW/cm² at 405 nm can produce a photo-flexoelectric coupling current of 85 nA, where the current peak has been enhanced by 121%. Due to the photo-flexoelectric coupling effect, the device has outstanding charging performance, where a 4.7 μF capacitor can be charged to 60 mV in 150 s. These devices have potential applications in multi-energy scavenging and self-powered sensors.

Influence of the Reference Electrode on the Performance of Single-Electrode Triboelectric Nanogenerators and the Optimization Strategies

Owing to their unique advantages, single-electrode triboelectric nanogenerators (SETENGs) have gained wide attention and have been applied in myriad areas, especially in the burgeoning flexible/wearable electronics. However, there is still a lack of a clear understanding of SETENGs. For example, previous simulation models generally put the reference electrode perpendicularly below the working part, but in practice, the reference electrode is designed in various scenarios and noticeable differences in outputs often occur when the reference electrode changes. With SETENGs developing towards wearability and portability, its reference electrode is often required to be constructed inside the device. Consequently, to achieve optimum performance, it is essential to understand the reference electrode's influence on the outputs. Here, the influence of the reference electrode on the performance of SETENGs is systematically investigated and the targeted optimization strategies are thoroughly revealed. First, theoretical simulations are conducted to investigate the reference electrode's effect on the performance of SETENGs with different structures and in various working modes. Secondly, the theoretical results are certified through corresponding experiments. Based on the results, the targeted optimization strategies for SETENGs are comprehensively demonstrated. This work provides fundamental guidance for the development of TENGs and the design and fabrication of new electronic devices.

Dual-Sensing Piezoresponsive Foam for Dynamic and Static Loading

Polymeric foams, embedded with nano-scale conductive particles, have previously been shown to display quasi-piezoelectric (QPE) properties; i.e., they produce a voltage in response to rapid deformation. This behavior has been utilized to sense impact and vibration in foam components, such as in sports padding and vibration-isolating pads. However, a detailed characterization of the sensing behavior has not been undertaken. Furthermore, the potential for sensing quasi-static deformation in the same material has not been explored. This paper provides new insights into these self-sensing foams by characterizing voltage response vs frequency of deformation. The correlation between temperature and voltage response is also quantified. Furthermore, a new sensing functionality is observed, in the form of a piezoresistive response to quasi-static deformation. The piezoresistive characteristics are quantified for both in-plane and through-thickness resistance configurations. The new functionality greatly enhances the potential applications for the foam, for example, as insoles that can characterize ground reaction force and pressure during dynamic and/or quasi-static circumstances, or as seat cushioning that can sense pressure and impact.

Enhancing the Output Performance of a Triboelectric Nanogenerator Based on Modified Polyimide and Sandwich-Structured Nanocomposite Film

Recently, scientists have been facing major obstacles in terms of improving the performances of dielectric materials for triboelectric nanogenerators. The triboelectric nanogenerator (TENG) is one of the first green energy technologies that can convert random mechanical kinetic energy into electricity. The surface charge density of TENGs is a critical factor speeding up their commercialization, so it is important to explore unique methods to increase the surface charge density. The key to obtaining a high-performance TENG is the preparation of dielectric materials with good mechanical properties, thermal stability and output performance. To solve the problem of the low output performance of PI-based triboelectric nanogenerators, we modified PI films by introducing nanomaterials and designed a new type of sandwich-shaped nanocomposite film. Herein, we used polyimide (PI) with ideal mechanical properties, excellent heat resistance and flexibility as the dielectric material, prepared an A-B-A sandwich structure with PI in the outer layer and modified a copper calcium titanate/polyimide (CCTO/PI) storage layer in the middle to improve the output of a TENG electrode. The doping amount of the CCTO was tailored. The results showed that at 8 wt% CCTO content, the electrical output performance was the highest, and the open-circuit voltage of CCTO/PI was 42 V. In the TENG, the open-circuit voltage, short-circuit current and transfer charge of the prepared sandwich-structured film were increased by 607%, 629% and 672% compared to the TENG with the PI thin film, respectively. This study presents a novel strategy of optimizing dielectric materials for triboelectric nano-generators and has great potential for the future development of high output-performance TENGs.

Enhanced triboelectric properties of Eu2O3-doped BaTiO3/PVDF-HFP nanofibers

Because triboelectric nanogenerators (TENGs) convert mechanical energy into electricity, they are sustainable energy sources for powering a diverse range of intelligent sensing and monitoring devices. To enhance the electrical output of polymer-based TENGs, nanofillers are commonly incorporated into polymers. In this study, we developed a simple low-temperature process for preparing high-performance ceramic powder-based TENGs comprising electrospun fibrous surfaces based on poly(vinylidene difluoride-co-hexafluoropropylene) (PVDF-HFP) and dispersed Eu₂O₃-doped BaTiO₃ nanofillers. Herein, we discuss the effect of the modified dielectric properties and transferred charge of the electrification film on the performance of the TENGs. After incorporating the Eu₂O₃-doped BaTiO₃ nanofiller, the maximum output voltage of the 10 wt% Eu₂O₃-BaTiO₃/PVDF-HFP electrospun-nanofiber TENG reached as high as 1004 V with a corresponding current density of 9.9 μA cm^-2. The enhancement in the triboelectric properties of the Eu₂O₃-BaTiO₃/PVDF-HFP electrospun-nanofiber TENGs was due to their high amounts of interface polarization and transferred charge, suggesting improved capture and storage of triboelectric electrons. These Eu₂O₃-BaTiO₃/PVDF-HFP electrospun-nanofiber TENGs could harvest mechanical energy and power electronic devices; they were robust and not affected by the operating temperature or humidity. Furthermore, we used a fabricated device as a sensor for application as a light-emitting diode dimmer switch and for the tracking of leg movement.

From Triboelectric Nanogenerator to Multifunctional Triboelectric Sensors: A Chemical Perspective toward the Interface Optimization and Device Integration

Triboelectric nanogenerators (TENGs) have intrigued scientists for their potential to alleviate the energy shortage crisis and facilitate self-powered sensors. Triboelectric interfaces containing triboelectric functionalized molecular groups and tunable surface charge densities are important for improving the electrical output capability of TENGs and the versatility of future electronics. In this review, following an introduction to the fundamental progress of TENG systems for mechanic energy harvesting, surface modifications that aim to increase the surface charge density and functionality are highlighted, with an emphasis on interfacial chemical modification and triboelectric energetics/dynamics optimization for efficient electrostatic induction and charge transfer. Recent advances in assemblies of multifunctional triboelectric sensing are briefly introduced, and future challenges and chemical perspectives in the field of TENG-based electronics are concisely reviewed. This review presents and advances the understanding of the state-of-the-art chemical strategies toward rational triboelectric interface engineering and system assembly and is expected to guide the rational design of highly efficient and versatile triboelectric sensing.

A computational modelling study of excitation of neuronal cells with triboelectric nanogenerators

Neurological disorders and nerve injuries, such as spinal cord injury, stroke, and multiple sclerosis can result in the loss of muscle function. Electrical stimulation of the neuronal cells is the currently available clinical treatment in this regard. As an effective energy harvester, the triboelectric nanogenerators (TENG) can be used for self-powered neural/muscle stimulations because the output of the TENG provides stimulation pulses for nerves. In the present study, using a computational modelling approach, the effect of surface micropatterns on the electric field distribution, induced voltage and capacitance of the TENG structures have been investigated. By incorporating the effect of the TENG inside the mathematical model of neuron’s electrical behavior (cable equation with Hodgkin-Huxley model), its impact on the electrical behavior of the neurons has been studied. The results show that the TENG operates differently with various surface modifications. The performance of the TENG in excitation of neurons depends on the contact and release speed of its electrodes accordingly.

Recent Development of Morphology-Controlled Hybrid Nanomaterials for Triboelectric Nanogenerator: A Review

Being cognizant of modern electronic devices, the scientists are continuing to investigate renewable green-energy resources for a decade. Amid different energy harvesting systems, the triboelectric nanogenerators (TENGs) have been found to be the most promising mechanical harvesting technology and have drawn attention to generate electrical energy. Thanks to its instant output power, choice to opt for wide-ranging materials, low maintenance cost, easy fabrication process and environmentally friendly nature. Due to numerous working modes of TENGs, it is dedicated to desired application at ambient conditions. In this review, an advance correlation of TENGs have been explained based on the variety of nanostructures, including 0D, 1D, 2D, 3D, metal organic frameworks (MOFs), coordination polymers (CPs), covalent organic frameworks (COFs), and perovskite materials. Moreover, an overview of previous and current perspectives of various nanomaterials, synthesis, fabrication and their applications in potential fields have been discussed in detail.

Self-Powered Tactile Sensor for Gesture Recognition Using Deep Learning Algorithms

A multifunctional wearable tactile sensor assisted by deep learning algorithms is developed, which can realize the functions of gesture recognition and interaction. This tactile sensor is the fusion of a triboelectric nanogenerator and piezoelectric nanogenerator to construct a hybrid self-powered sensor with a higher power density and sensibility. The power generation performance is characterized with an open-circuit voltage V_OC of 200 V, a short-circuit current I_SC of 8 μA, and a power density of 0.35 mW cm^-2 under a matching load. It also has an excellent sensibility, including a response time of 5 ms, a signal-to-noise ratio of 22.5 dB, and a pressure resolution of 1% (1-10 kPa). The sensor is successfully integrated on a glove to collect the electrical signal output generated by the gesture. Using deep learning algorithms, the functions of gesture recognition and control can be realized in real time. The combination of tactile sensor and deep learning algorithms provides ideas and guidance for its applications in the field of artificial intelligence, such as human-computer interaction, signal monitoring, and smart sensing.

Droplet Bouncing: Fundamentals, Regulations, and Applications

Droplet impact is a ubiquitous phenomenon in nature, daily life, and industrial processes. It is thus crucial to tune the impact outcomes for various applications. As a special outcome of droplet impact, the bouncing of droplets keeps the form of the droplets after the impact and minimizes the energy loss during the impact, being beneficial in many applications. A unified understanding of droplet bouncing is in high demand for effective development of new techniques to serve applications. This review shows the fundamentals, regulations, and applications of millimeter-sized droplet bouncing on solid surfaces and same/miscible liquids (liquid pool and another droplet). Regulation methods and current applications are summarized, and potential directions are proposed.

Ultra-Sensitive, Deformable, and Transparent Triboelectric Tactile Sensor Based on Micro-Pyramid Patterned Ionic Hydrogel for Interactive Human-Machine Interfaces

Rapid advances in wearable electronics and mechno-sensational human-machine interfaces impose great challenges in developing flexible and deformable tactile sensors with high efficiency, ultra-sensitivity, environment-tolerance, and self-sustainability. Herein, a tactile hydrogel sensor (THS) based on micro-pyramid-patterned double-network (DN) ionic organohydrogels to detect subtle pressure changes by measuring the variations of triboelectric output signal without an external power supply is reported. By the first time of pyramidal-patterned hydrogel fabrication method and laminated polydimethylsiloxane (PDMS) encapsulation process, the self-powered THS shows the advantages of remarkable flexibility, good transparency (≈85%), and excellent sensing performance, including extraordinary sensitivity (45.97 mV Pa^-1 ), fast response (≈20 ms), very low limit of detection (50 Pa) as well as good stability (36 000 cycles). Moreover, with the LiBr immersion treatment method, the THS possesses excellent long-term hyper anti-freezing and anti-dehydrating properties, broad environmental tolerance (-20 to 60 °C), and instantaneous peak power density of 20 µW cm^-2 , providing reliable contact outputs with different materials and detecting very slight human motions. By integrating the signal acquisition/process circuit, the THS with excellent self-power sensing ability is utilized as a switching button to control electric appliances and robotic hands by simulating human finger gestures, offering its great potentials for wearable and multi-functional electronic applications.

Harvesting circuits for triboelectric nanogenerators for wearable applications

Internet of Things (IoT) and recently Internet of Nano Things (IoNT) bear the promise of new devices able to communicate and assist our daily lives toward wearable technologies which demand a versatile integration such as in wireless body networks (WBN), sensing, and health monitorization. These must comply with stringent constraints on energy usage. Dimensions and complexity intensify the need for small and maintenance-free power sources. Environment energy harvesting and storage is an important approach to sustain operation for a long time. Triboelectric nanogenerators (TENGs) arise as a strong and promising solution to power the new field of outcoming self-sustainable devices, implantable, and wearable devices. They can transform mechanical energy in different modes, have simple structures, and use vulgar and sustainable materials. This paper makes a review about TENGs technology, construction, materials, operation, and focus on strategies for harvesting circuits. Main challenges like efficiency, reliability, energy storage, and sustainability are discussed.

Flexible alternating current electroluminescent devices integrated with high voltage triboelectric nanogenerators

Flexible alternating current electroluminescent (ACEL) devices have attracted growing interest as promising wearable displays for their uniformity of light emission, low power consumption, and excellent reliability. However, the requirement of high-voltage power sources for driving ACEL devices greatly impedes their portability and commercialization. Here, we developed flexible ACEL devices integrated with high output-voltage triboelectric nanogenerators (TENG) using easy and low-cost crumpled Al electrodes. The output voltage and current could reach as high as 490 V and 71.74 μA, corresponding to the maximum instantaneous output power density of 1.503 mW cm^-2, which was demonstrated to power an integrated flexible ACEL patterned display. In addition, through signal acquisition and transmission, ACEL can display the compression frequency of TENG in real time. Such self-powered ACEL devices are very promising as flexible displays in wearable electronics.

Flexible Triboelectric Nanogenerators Based on Electrospun Poly(vinylidene fluoride) with MoS2/Carbon Nanotube Composite Nanofibers

With the miniaturization of wearable smart devices, the demand for portable and sustainable power sources is increasing. Herein, a flexible and lightweight triboelectric nanogenerator (PMC-TENG) was fabricated with MoS₂/carbon nanotube (MC)-doped PVDF as the friction substrate based on electrospinning for harvesting random body motion energy under complex mechanical deformations. The charge density on the friction surface of PVDF nanofibers was found to increase significantly as the introduced electron acceptor of the MC composite, and nylon as a clothing material for another friction layer simplifies the structure of the device. Upon optimization of the electrospinning preparation process, the output voltage of the prepared PMC-TENG can reach >300 V and the instantaneous power can reach 0.484 mW (∼6 cm × 6 cm). At the same time, the PMC-TENG remains stable over 3000 cycles and has the ability to charge a capacitor. The flexible device demonstrates an excellent capability of converting mechanical energy to electrical energy. Therefore, this study has good prospects for application in the field of power supply for portable electronic devices and others.

Enhancement of patterned triboelectric output performance by an interfacial polymer layer for energy harvesting application

Efficaciously scavenging waste mechanical energy from the environment is an emerging field in the self-powered and self-governing electronics systems which solves battery limitations. It demonstrates enormous potential in various fields such as wireless devices, vesture, and portable electronic devices. Different surface textured PET triboelectric nanogenerators (TENGs) were developed by the laser pattern method in the previous work, with the line textured TENG device showing improved performance due to a larger surface contact area. Here, a polyethylene oxide (PEO) and polyvinyl alcohol (PVA) coated line patterned PET-based TENG was developed for the conversion of mechanical energy into useful electric energy. The PEO layer boosted the TENG output to 4 times higher than that of the PA6-laser patterned PET TENG device (our previous report) and 2-fold higher than that of a pristine line patterned TENG. It generated an open-circuit voltage, short circuit current, and instantaneous power density of 131 V, 2.32 μA, and 41.6 μW cm^-2, respectively. The as-fabricated device was tested for 10 000 cycles for reliability evaluation, which shows no significant performance degradation. In addition, the device was deployed to power 10 LEDs with high intensity. Thus, this device can be used for ambient mechanical energy conversion and to power micro and nano-electronic devices.

Self-Powered Load Sensing Circuitry for Total Knee Replacement

There has been a significant increase in the number of total knee replacement (TKR) surgeries over the past few years, particularly among active young and elderly people suffering from knee pain. Continuous and optimal monitoring of the load on the knee is highly desirable for designing more reliable knee implants. This paper focuses on designing a smart knee implant consisting of a triboelectric energy harvester and a frontend electronic system to process the harvested signal for monitoring the knee load. The harvester produces an AC signal with peak voltages ranging from 10 V to 150 V at different values of knee cyclic loads. This paper demonstrates the measurement results of a PCB prototype of the frontend electronic system fabricated to verify the functionality and feasibility of the proposed approach for a small range of cycling load. The frontend electronic system consists of a voltage processing unit to attenuate high peak voltages, a rectifier and a regulator to convert the input AC signal into a stabilized DC signal. The DC voltage signal provides biasing for the delta-sigma analog-to-digital converter (ADC). Thus, the output of the triboelectric harvester acts as both the power signal that is rectified/regulated and data signal that is digitized. The power consumption of the proposed PCB design is approximately 5.35 μW. Next, the frontend sensor circuitry is improved to accommodate a wider range of cyclic load. These results demonstrate that triboelectric energy harvesting is a promising technique for self-monitoring the load inside knee implants.

From contact electrification to triboelectric nanogenerators

Although the contact electrification (CE) (or usually called 'triboelectrification') effect has been known for over 2600 years, its scientific mechanism still remains debated after decades. Interest in studying CE has been recently revisited due to the invention of triboelectric nanogenerators (TENGs), which are the most effective approach for converting random, low-frequency mechanical energy (called high entropy energy) into electric power for distributed energy applications. This review is composed of three parts that are coherently linked, ranging from basic physics, through classical electrodynamics, to technological advances and engineering applications. First, the mechanisms of CE are studied for general cases involving solids, liquids and gas phases. Various physics models are presented to explain the fundamentals of CE by illustrating that electron transfer is the dominant mechanism for CE for solid-solid interfaces. Electron transfer also occurs in the CE at liquid-solid and liquid-liquid interfaces. An electron-cloud overlap model is proposed to explain CE in general. This electron transfer model is extended to liquid-solid interfaces, leading to a revision of the formation mechanism of the electric double layer at liquid-solid interfaces. Second, by adding a time-dependent polarization termPscreated by the CE-induced surface electrostatic charges in the displacement fieldD, we expand Maxwell's equations to include both the medium polarizations due to electric field (P) and mechanical aggitation and medium boundary movement induced polarization term (Ps). From these, the output power, electromagnetic (EM) behaviour and current transport equation for a TENG are systematically derived from first principles. A general solution is presented for the modified Maxwell's equations, and analytical solutions for the output potential are provided for a few cases. The displacement current arising fromε∂E/∂t is responsible for EM waves, while the newly added term ∂Ps/∂t is responsible for energy and sensors. This work sets the standard theory for quantifying the performance and EM behaviour of TENGs in general. Finally, we review the applications of TENGs for harvesting all kinds of available mechanical energy that is wasted in our daily life, such as human motion, walking, vibration, mechanical triggering, rotating tires, wind, flowing water and more. A summary is provided about the applications of TENGs in energy science, environmental protection, wearable electronics, self-powered sensors, medical science, robotics and artificial intelligence.

Recent Advances of Energy Solutions for Implantable Bioelectronics

The emerging field of implantable bioelectronics has attracted widespread attention in modern society because it can improve treatment outcomes, reduce healthcare costs, and lead to an improvement in the quality of life. However, their continuous operation is often limited by conventional bulky and rigid batteries with a limited lifespan, which must be surgically removed after completing their missions and/or replaced after being exhausted. Herein, this paper gives a comprehensive review of recent advances in nonconventional energy solutions for implantable bioelectronics, emphasizing the miniaturized, flexible, biocompatible, and biodegradable power devices. According to their source of energy, the promising alternative energy solutions are sorted into three main categories, including energy storage devices (batteries and supercapacitors), internal energy-harvesting devices (including biofuel cells, piezoelectric/triboelectric energy harvesters, thermoelectric and biopotential power generators), and external wireless power transmission technologies (including inductive coupling/radiofrequency, ultrasound-induced, and photovoltaic devices). Their fundamentals, materials strategies, structural design, output performances, animal experiments, and typical biomedical applications are also discussed. It is expected to offer complementary power sources to extend the battery lifetime of bioelectronics while acting as an independent power supply. Thereafter, the existing challenges and perspectives associated with these powering devices are also outlined, with a focus on implantable bioelectronics.

Self-powered technology based on nanogenerators for biomedical applications

Biomedical electronic devices have enormous benefits for healthcare and quality of life. Still, the long-term working of those devices remains a great challenge due to the short life and large volume of conventional batteries. Since the nanogenerators (NGs) invention, they have been widely used to convert various ambient mechanical energy sources into electrical energy. The self-powered technology based on NGs is dedicated to harvesting ambient energy to supply electronic devices, which is an effective pathway to conquer the energy insufficiency of biomedical electronic devices. With the aid of this technology, it is expected to develop self-powered biomedical electronic devices with advanced features and distinctive functions. The goal of this review is to summarize the existing self-powered technologies based on NGs and then review the applications based on self-powered technologies in the biomedical field during their rapid development in recent years, including two main directions. The first is the NGs as independent sensors to converts biomechanical energy and heat energy into electrical signals to reflect health information. The second direction is to use the electrical energy produced by NGs to stimulate biological tissues or powering biomedical devices for achieving the purpose of medical application. Eventually, we have analyzed and discussed the remaining challenges and perspectives of the field. We believe that the self-powered technology based on NGs would advance the development of modern biomedical electronic devices.

Review: Sensors for Biosignal/Health Monitoring in Electronic Skin

Skin is the largest sensory organ and receives information from external stimuli. Human body signals have been monitored using wearable devices, which are gradually being replaced by electronic skin (E-skin). We assessed the basic technologies from two points of view: sensing mechanism and material. Firstly, E-skins were fabricated using a tactile sensor. Secondly, E-skin sensors were composed of an active component performing actual functions and a flexible component that served as a substrate. Based on the above fabrication processes, the technologies that need more development were introduced. All of these techniques, which achieve high performance in different ways, are covered briefly in this paper. We expect that patients' quality of life can be improved by the application of E-skin devices, which represent an applied advanced technology for real-time bio- and health signal monitoring. The advanced E-skins are convenient and suitable to be applied in the fields of medicine, military and environmental monitoring.

Combination of Piezoelectric and Triboelectric Devices for Robotic Self-Powered Sensors

Sensors are an important part of the organization required for robots to perceive the external environment. Self-powered sensors can be used to implement energy-saving strategies in robots and reduce their power consumption, owing to their low-power consumption characteristics. The triboelectric nanogenerator (TENG) and piezoelectric transducer (PE) are important implementations of self-powered sensors. Hybrid sensors combine the advantages of the PE and TENG to achieve higher sensitivity, wider measurement range, and better output characteristics. This paper summarizes the principles and research status of pressure sensors, displacement sensors, and three-dimensional (3D) acceleration sensors based on the self-powered TENG, PE, and hybrid sensors. Additionally, the basic working principles of the PE and TENG are introduced, and the challenges and problems in the development of PE, TENG, and hybrid sensors in the robotics field are discussed with regard to the principles of the self-powered pressure sensors, displacement sensors, and 3D acceleration sensors applied to robots.

Progress on Self-Powered Wearable and Implantable Systems Driven by Nanogenerators

With the rapid development of the internet of things (IoT), sustainable self-powered wireless sensory systems and diverse wearable and implantable electronic devices have surged recently. Under such an opportunity, nanogenerators, which can convert continuous mechanical energy into usable electricity, have been regarded as one of the critical technologies for self-powered systems, based on the high sensitivity, flexibility, and biocompatibility of piezoelectric nanogenerators (PENGs) and triboelectric nanogenerators (TENGs). In this review, we have thoroughly analyzed the materials and structures of wearable and implantable PENGs and TENGs, aiming to make clear how to tailor a self-power system into specific applications. The advantages in TENG and PENG are taken to effectuate wearable and implantable human-oriented applications, such as self-charging power packages, physiological and kinematic monitoring, in vivo and in vitro healing, and electrical stimulation. This review comprehensively elucidates the recent advances and future outlook regarding the human body's self-powered systems.

Air-gap embedded triboelectric nanogenerator via surface modification of non-contact layer using sandpapers

With the increased number of small electronics and demand for their energy source, renewable energy sources have received much attention. Above all, a triboelectric nanogenerator (TENG) based on the combination of contact electrification and electrostatic induction has been researched as a method of converting mechanical energy into electricity. In order to increase the electrical output of TENGs with raising the surface charge density, a lot of researchers have focused on the fabrication methods to employ micro-/nano-structures onto a contact surface of the TENG, but have been facing several issues regarding the degradation of the output performance from the iterative operation process. Hence, it is highly required to introduce an approach to enhancing the performance of TENG, while minimally degrading the output power during the long-term operation. In this paper, an air-gap embedded TENG (AE-TENG), which contains a microstructure on the non-contact surface by means of a sandpaper, is proposed. These small air-gaps between the spin-coated polydimethylsiloxane and the non-contact surface can significantly boost the total surface charge density of the dielectric layer. Thus, the electrical output performance of the AE-TENG is enhanced without any surface engineering on the contact surface. Furthermore, the effect of the air-gap induced surface charges on the electric potential is systematically analyzed by not only experimentally electrical outputs, but theoretical and computational modeling based on the V-Q-x relationship and simulation software tool. This air-gap induced triboelectric effect opens a new perspective of the development of electrical outputs by providing a structural/theoretical understanding for TENGs.

Moderately Transparent Chitosan-PVA Blended Membrane for Strong Mechanical Stiffness and as a Robust Bio-Material Energy Harvester Through Contact-Separation Mode TENG

The detection of sustainable materials from naturally available resources using a simple fabrication process is highly important for novel research. Here, we used chitosan-PVA (Chs-PVA) blend films via layer-by-layer casting technologies for generating power through mechanical induction through triboelectric nanogenerators. The proposed Chs-PVA biodegradable film (i.e., thickness of 60 ± 5 μm) is facile, ecofriendly, highly flexible, mechanically strong, cost-effective, and easy to scale up. FT-IR analysis of the ChS-PVA blend membrane showed the strong interactions between the amines of ChS and hydroxyl groups of PVA through chemical cross-linking by hydrogen bonding. More importantly, the triboelectric nanogenerators (TENG) values of ChS-PVA films were 3–4 orders of magnitude lower than chitosan films reported before. Layer-on-layer cast films in particular exhibited high tensile strength (15.8 ± 1 MPa) and were more than three times stronger than other polyelectrolyte multilayer films. Both types of films remained stable in an acidic environment. Furthermore, the layer-on-layer-assembled films presented greater open circuit voltage (Voc) and short circuit current (Isc) values compared to pure ChS and PVA films. The ChS-PVA membrane can be used as a functional layer to produce charges by collecting get-up-and-go through vertical contact and separation mode TENG counters to the PVDF membrane. The enhancement of Voc and Isc of ChS-PVA TENG were 244 and 1,080% from ChS TENG. Where in the case of PVA TENG, the enhancement of Voc and Isc were increased by 633 and 2,888%, respectively due to the availability of free loan pair on the -NH2 and -OH functional groups. The novel ChS-PVA TENG is a potential candidate for satisfying the tight requirement of an optimized energy harvesting device as an alternate bio-material option for contact-separation mode TENGs.

Hierarchical Honeycomb-Structured Electret/Triboelectric Nanogenerator for Biomechanical and Morphing Wing Energy Harvesting

Flexible, compact, lightweight and sustainable power sources are indispensable for modern wearable and personal electronics and small-unmanned aerial vehicles (UAVs). Hierarchical honeycomb has the unique merits of compact mesostructures, excellent energy absorption properties and considerable weight to strength ratios. Herein, a honeycomb-inspired triboelectric nanogenerator (h-TENG) is proposed for biomechanical and UAV morphing wing energy harvesting based on contact triboelectrification wavy surface of cellular honeycomb structure. The wavy surface comprises a multilayered thin film structure (combining polyethylene terephthalate, silver nanowires and fluorinated ethylene propylene) fabricated through high-temperature thermoplastic molding and wafer-level bonding process. With superior synchronization of large amounts of energy generation units with honeycomb cells, the manufactured h-TENG prototype produces the maximum instantaneous open-circuit voltage, short-circuit current and output power of 1207 V, 68.5 μA and 12.4 mW, respectively, corresponding to a remarkable peak power density of 0.275 mW cm^-3 (or 2.48 mW g^-1) under hand pressing excitations. Attributed to the excellent elastic property of self-rebounding honeycomb structure, the flexible and transparent h-TENG can be easily pressed, bent and integrated into shoes for real-time insole plantar pressure mapping. The lightweight and compact h-TENG is further installed into a morphing wing of small UAVs for efficiently converting the flapping energy of ailerons into electricity for the first time. This research demonstrates this new conceptualizing single h-TENG device's versatility and viability for broad-range real-world application scenarios.

An Optimized Flutter-Driven Triboelectric Nanogenerator with a Low Cut-In Wind Speed

We present an optimized flutter-driven triboelectric nanogenerator (TENG) for wind energy harvesting. The vibration and power generation characteristics of this TENG are investigated in detail, and a low cut-in wind speed of 3.4 m/s is achieved. It is found that the air speed, the thickness and length of the membrane, and the distance between the electrode plates mainly determine the PTFE membrane’s vibration behavior and the performance of TENG. With the optimized value of the thickness and length of the membrane and the distance of the electrode plates, the peak open-circuit voltage and output power of TENG reach 297 V and 0.46 mW at a wind speed of 10 m/s. The energy generated by TENG can directly light up dozens of LEDs and keep a digital watch running continuously by charging a capacitor of 100 μF at a wind speed of 8 m/s.

Triboelectric nanogenerators for human-health care

Since the world's first triboelectric nanogenerator (TENG) was proposed in 2012, numerous TENG-based devices and equipment have sprung up in various fields. In particular, TENG has great potential in the field of human-health care due to its small size, self-powered and low cost. With the continuous deepening of TENG research, its structure, function and technical concept are becoming more and more abundant. In order to summarize the progress and development status of TENG in health care, based on the different types of applications subdirection, this paper reviews the TENG-based research work of this field in recent eight years. The characteristics of various types of TENG-based applications and their corresponding technologies are introduced and analyzed, under the comparison of their structure and performance. This review is dedicated to provide reference and inspiration for the future development and innovation of TENG for health care.

UV-Protective, Self-Cleaning, and Antibacterial Nanofiber-Based Triboelectric Nanogenerators for Self-Powered Human Motion Monitoring

Equipping wearable electronics with special functions will endow them with more additional values and more comprehensive practical performance. Here, we report an ultraviolet (UV)-protective, self-cleaning, antibacterial, and self-powered all-nanofiber-based triboelectric nanogenerator (TENG) for mechanical energy harvesting and self-powered sensing, which is fabricated with Ag nanowires (NWs)/TPU nanofibers and the TiO₂@PAN networks through a facile electrospinning method. Due to the added TiO₂ nanoparticles (NPs), the TENG presents excellent UV-protective performance, including the ultraviolet protection factor (UPF) of ∼204, the transmittance of UVA (T_UVA) of ∼0.0574%, and the transmittance of UVB (T_UVB) ∼0.107%. Furthermore, under solar lighting for 25 min, most surface contamination can be degraded, and the decreased power output would be recovered. Owing to the coupled effects of TiO₂ NPs and Ag NWs, the TENG shows excellent antibacterial activity against Staphylococcus aureus. Due to the micro-to-nano hierarchical porous structure, the all-nanofiber-based TENG can serve as self-powered pedometers for detecting and tracking human motion behaviors. As a multifunctional self-powered device, the TENG prompts various applications in the fields of micro/nanopower sources, human movement monitoring, and human-machine interfaces, potentially providing an alternative energy solution and a multifunctional interactive platform for the next-generation wearable electronics.

The Interface between Nanoenergy and Self-Powered Electronics

In recent decades, nanogenerators based on several techniques such as triboelectric effects, piezoelectric effects, or other mechanisms have experienced great developments. The nanoenergy generated by nanogenerators is supposed to be used to overcome the problem of energy supply problems for portable electronics and to be applied to self-powered microsystems including sensors, actuators, integrated circuits, power sources, and so on. Researchers made many attempts to achieve a good solution and have performed many explorations. Massive efforts have been devoted to developing self-powered electronics, such as self-powered communication devices, self-powered human-machine interfaces, and self-powered sensors. To take full advantage of nanoenergy, we need to review the existing applications, look for similarities and differences, and then explore the ways of achieving various self-powered systems with better performance. In this review, the methods of applying nanogenerators in specific circumstances are studied. The applications of nanogenerators are classified into two categories, direct utilization and indirect utilization, according to whether a treatment process is needed. We expect to offer a line of thought for future research on self-powered electronics.

Textile-Based Triboelectric Nanogenerators for Wearable Self-Powered Microsystems

In recent years, wearable electronic devices have made considerable progress thanks to the rapid development of the Internet of Things. However, even though some of them have preliminarily achieved miniaturization and wearability, the drawbacks of frequent charging and physical rigidity of conventional lithium batteries, which are currently the most commonly used power source of wearable electronic devices, have become technical bottlenecks that need to be broken through urgently. In order to address the above challenges, the technology based on triboelectric effect, i.e., triboelectric nanogenerator (TENG), is proposed to harvest energy from ambient environment and considered as one of the most promising methods to integrate with functional electronic devices to form wearable self-powered microsystems. Benefited from excellent flexibility, high output performance, no materials limitation, and a quantitative relationship between environmental stimulation inputs and corresponding electrical outputs, TENGs present great advantages in wearable energy harvesting, active sensing, and driving actuators. Furthermore, combined with the superiorities of TENGs and fabrics, textile-based TENGs (T-TENGs) possess remarkable breathability and better non-planar surface adaptability, which are more conducive to the integrated wearable electronic devices and attract considerable attention. Herein, for the purpose of advancing the development of wearable electronic devices, this article reviews the recent development in materials for the construction of T-TENGs and methods for the enhancement of electrical output performance. More importantly, this article mainly focuses on the recent representative work, in which T-TENGs-based active sensors, T-TENGs-based self-driven actuators, and T-TENGs-based self-powered microsystems are studied. In addition, this paper summarizes the critical challenges and future opportunities of T-TENG-based wearable integrated microsystems.

Optimization of ZnO Nanorods Concentration in a Micro-Structured Polymeric Composite for Nanogenerators

The growing use of wearable devices has been stimulating research efforts in the development of energy harvesters as more portable and practical energy sources alternatives. The field of piezoelectric nanogenerators (PENGs) and triboelectric nanogenerators (TENGs), especially employing zinc oxide (ZnO) nanowires (NWs), has greatly flourished in recent years. Despite its modest piezoelectric coefficient, ZnO is very attractive due to its sustainable raw materials and the facility to obtain distinct morphologies, which increases its multifunctionality. The integration of ZnO nanostructures into polymeric matrices to overcome their fragility has already been proven to be fruitful, nevertheless, their concentration in the composite should be optimized to maximize the harvesters’ output, an aspect that has not been properly addressed. This work studies a composite with variable concentrations of ZnO nanorods (NRs), grown by microwave radiation assisted hydrothermal synthesis, and polydimethylsiloxane (PDMS). With a 25 wt % ZnO NRs concentration in a composite that was further micro-structured through laser engraving for output enhancement, a nanogenerator (NG) was fabricated with an output of 6 V at a pushing force of 2.3 N. The energy generated by the NG could be stored and later employed to power small electronic devices, ultimately illustrating its potential as an energy harvesting device.

Wearable triboelectric sensors for biomedical monitoring and human-machine interface

A growing advocacy of healthy and quality life makes wearable electronics spring up. Triboelectric nanogenerator (TENG) has developed as an energy harvesting technology and as an advanced sensor technology in wearable electronics. The triboelectric sensor (TS) is sensitive to the mechanical motion and driven by the motion itself. Therefore, TS is capable of monitoring certain vital signs and kinds of movements of human body. Based on these monitoring, novel human-machine interfaces (HMIs) can be established. In this review, a comprehensive overview of some key progresses in this field over last 5 years are presented. Several main aspects of biomedical monitoring based on TSs are classified: pulse/cardiac/micro-motion, respiration/airflow/vibration, and pressure/tactile/body movement. The major types of HMIs taking these biomedical monitoring as basis are introduced accordingly: eye movement, voice/auditory, gesture/joint movement, and touch/tactile based HMIs. Finally, the current limitations and future trends are put forward for biomedical monitoring and HMIs based on TSs.

Parametric Study of a Triboelectric Transducer in Total Knee Replacement Application

Triboelectric energy harvesting is a relatively new technology showing promise for biomedical applications. This study investigates a triboelectric energy transducer for potential applications in total knee replacement (TKR) both as an energy harvester and a sensor. The sensor can be used to monitor loads at the knee joint. The proposed transducer generates an electrical signal that is directly related to the periodic mechanical load from walking. The proportionality between the generated electrical signal and the load transferred to the knee enables triboelectric transducers to be used as self-powered active load sensors. We analyzed the performance of a triboelectric transducer when subjected to simulated gait loading on a joint motion simulator. Two different designs were evaluated, one made of Titanium on Aluminum, (Ti-PDMS-Al), and the other made of Titanium on Titanium, (Ti-PDMS-Ti). The Ti-PDMS-Ti design generates more power than Ti-PDMS-Al and was used to optimize the structural parameters. Our analysis found these optimal parameters for the Ti-PDMS-Ti design: external resistance of 304 MΩ, a gap of 550 μm, and a thickness of the triboelectric layer of 50 μm. Those parameters were optimized by varying resistance, gap, and the thickness while measuring the power outputs. Using the optimized parameters, the transducer was tested under different axial loads to check the viability of the harvester to act as a self-powered load sensor to estimate the knee loads. The forces transmitted across the knee joint during activities of daily living can be directly measured and used for self-powering, which can lead to improving the total knee implant functions.

Biopolymer Nanofibers for Nanogenerator Development

The development of nanogenerators (NGs) with optimal performances and functionalities requires more novel materials. Over the past decade, biopolymer nanofibers (BPNFs) have become critical sustainable building blocks in energy-related fields because they have distinctive nanostructures and properties and can be obtained from abundant and renewable resources. This review summarizes recent advances in the use of BPNFs for NG development. We will begin by introducing various strategies for fabricating BPNFs with diverse structures and performances. Then, we will systematically present the utilization of polysaccharide and protein nanofibers for NGs. We will mainly focus on the use of BPNFs to generate bulk materials with tailored structures and properties for assembling of triboelectric and piezoelectric NGs. The use of BPNFs to construct NGs for the generation of electricity from moisture and osmosis is also discussed. Finally, we illustrate our personal perspectives on several issues that require special attention with regard to future developments in this active field.

Moisture-Enabled Electricity Generation: From Physics and Materials to Self-Powered Applications

The exploration of the utilization of sustainable, green energy represents one way in which it is possible to ameliorate the growing threat of the global environmental issues and the crisis in energy. Moisture, which is ubiquitous on Earth, contains a vast reservoir of low-grade energy in the form of gaseous water molecules and water droplets. It has now been found that a number of functionalized materials can generate electricity directly from their interaction with moisture. This suggests that electrical energy can be harvested from atmospheric moisture and enables the creation of a new range of self-powered devices. Herein, the basic mechanisms of moisture-induced electricity generation are discussed, the recent advances in materials (including carbon nanoparticles, graphene materials, metal oxide nanomaterials, biofibers, and polymers) for harvesting electrical energy from moisture are summarized, and some strategies for improving energy conversion efficiency and output power in these devices are provided. The potential applications of moisture electrical generators in self-powered electronics, healthcare, security, information storage, artificial intelligence, and Internet-of-things are also discussed. Some remaining challenges are also considered, together with a number of suggestions for potential new developments of this emerging technology.

Leverage Surface Chemistry for High-Performance Triboelectric Nanogenerators

Triboelectric Nanogenerators (TENGs) are a highly efficient approach for mechanical-to-electrical energy conversion based on the coupling effects of contact electrification and electrostatic induction. TENGs have been intensively applied as both sustainable power sources and self-powered active sensors with a collection of compelling features, including lightweight, low cost, flexible structures, extensive material selections, and high performances at low operating frequencies. The output performance of TENGs is largely determined by the surface triboelectric charges density. Thus, manipulating the surface chemical properties via appropriate modification methods is one of the most fundamental strategies to improve the output performances of TENGs. This article systematically reviews the recently reported chemical modification methods for building up high-performance TENGs from four aspects: functional groups modification, ion implantation and decoration, dielectric property engineering, and functional sublayers insertion. This review will highlight the contribution of surface chemistry to the field of triboelectric nanogenerators by assessing the problems that are in desperate need of solving and discussing the field's future directions.

Single-Layer Triboelectric Nanogenerators Based on Ion-Doped Natural Nanofibrils

As emerging ambient energy harvesting technology, triboelectric nanogenerators (TENGs) have proven to be a robust power source and have demonstrated the unique ability to power micro-nano electronics autonomously to form self-powered devices. Although four working modes of TENGs have been developed to promote the feasibility of self-powered micro-nano systems, the relatively complicated structure composed of multilayer and movable components limits the practical applications of TENGs. Herein, we propose a single-layer triboelectric nanogenerator (SL-TENG) based on ion-doped natural nanofibrils. Compared with the simplest mode of currently existing TENGs, i.e., the single-electrode type, this novel single-electrode TENG further simplifies the configuration by the removal of the dielectric layer. The underlying mechanism of the proposed SL-TENG is comprehensively investigated through electrical measurements and the analysis of the effect of ion species at different concentrations. In contrast to conventional TENGs that require electrodes to realize charge transfer, it is revealed that the ions doped into natural nanofibrils effectively realize charge transfer due to the separation and migration of cations and anions. This new working principle based on the combination of electrons and ions enables TENGs to show greater potential for applications since the ultrasimple single-layer configuration enables them to be more easily integrated with other electronic components; additionally, the whole device of the proposed SL-TENG is biodegradable because the natural nanofibrils are completely extracted from carrots.