Metal-free Ketjenblack incorporated nitrogen-doped carbon sheets derived from gelatin as oxygen reduction catalysts

Tailored Heterojunction Active Sites for Oxygen Electrocatalyst Promotion in Zinc-Air Batteries

Rechargeable zinc-air batteries (ZABs) are promising energy storage systems due to their low-cost and safety. However, the working principle of ZABs is based on oxygen evolution reaction (OER) and oxygen reduction reaction (ORR), which display sluggish kinetic and low stability. Herein, this work proposes a novel method to design a heterogeneous CoP/CoO electrocatalyst on mesopore nanobox carbon/carbon nanotube (CoP/CoO@MNC-CNT) that enriched active sites and synergistic effect. Moreover, the well-defined heterointerfaces could lower the energy barrier for intermediate species adsorption and promote OER and ORR electrochemical performances. The CoP/CoO@MNC-CNT electrocatalyst presents a high half-wave potential of 0.838 V for ORR and a small overpotential of 270 mV for OER. The ZABs-based CoP/CoO@MNC-CNT air-cathode shows an open-circuit voltage of 1.409 V, the long-term cycle life of 500 h with a small voltage difference change of 7.7%. Additionally, the flexible ZABs exhibit highly mechanical stability, demonstrating their application potential in wearable electronic devices.

Insights into Nitrogen-doped Carbon for Oxygen Reduction: The Role of Graphitic and Pyridinic Nitrogen Species

Nitrogen-doped carbons (N/Cs) manifest good catalytic performance for oxygen reduction reaction (ORR) for fuel cell systems. However, to date, controversies remain on the role of active sites in N/Cs. In the present study, ORR test was conducted on three N/Cs in O₂ -saturated 0.1 M KOH aqueous solution, where apparent linear correlation between graphitic N contents and ORR activity was observed. Theoretical calculations demonstrated that graphitic N doping is energetically more favorable than that of pyridinic N doping for ORR and the pyridinic N leads to more preferential with 2 e^- ORR pathway. These results reveal that graphitic N plays a key role in N/Cs mediated ORR activity. This work lays a solid foundation on identifying the active sites in heteroatom-doped carbons and can be exploited for rational design and engineering of effective carbon-based ORR catalysts.

Preparation of N-doped carbon materials from cellulose:chitosan blends and their potential application in electrocatalytic oxygen reduction

Carbon-based electrocatalysts for oxygen reduction reaction (ORR) are prepared by a direct pathway including a two-step thermal treatment process applied to porous spheres of natural biopolymer blends. Cellulose blends with chitosan are first thermally treated at moderate temperatures (e.g., 200 °C), then pyrolyzed at elevated temperature (800–1000 °C), both steps under a constant nitrogen flow. By blending of cellulose with chitosan, the nitrogen content in the final carbon-based catalyst can be considerably increased. The influence of the composition of the precursor biopolymer blend on the ORR electrocatalytic activity is analyzed in correlation with the elemental composition and other structural features of the catalyst. The polymer blend containing cellulose:chitosan = 75:25, thermally treated 1 h at 200 °C and pyrolyzed 1 h at 800 °C under nitrogen atmosphere, shows the highest electrocatalytic ORR activity. This is attributed to an increased surface area combined with relatively high nitrogen content and a higher pyridinic/pyrrolic species ratio.

Successful Manufacturing Protocols of N-Rich Carbon Electrodes Ensuring High ORR Activity: A Review

The exploration and development of different carbon nanomaterials happening over the past years have established carbon electrodes as an important electrocatalyst for oxygen reduction reaction. Metal-free catalysts are especially promising potential alternatives for replacing Pt-based catalysts. This article describes recent advances and challenges in the three main synthesis manners (i.e., pyrolysis, hydrothermal method, and chemical vapor deposition) as effective methods for the production of metal-free carbon-based catalysts. To improve the catalytic activity, heteroatom doping the structure of graphene, carbon nanotubes, porous carbons, and carbon nanofibers is important and makes them a prospective candidate for commercial applications. Special attention is paid to providing an overview on the recent major works about nitrogen-doped carbon electrodes with various concentrations and chemical environments of the heteroatom active sites. A detailed discussion and summary of catalytic properties in aqueous electrolytes is given for graphene and porous carbon-based catalysts in particular, including recent studies performed in the authors’ research group. Finally, we discuss pathways and development opportunities approaching the practical use of mainly graphene-based catalysts for metal–air batteries and fuel cells.

Dual Inorganic Sacrificial Template Synthesis of Hierarchically Porous Carbon with Specific N Sites for Efficient Oxygen Reduction

It is still a challenge to achieve efficiently controlled preparation of functional oxygen reduction reaction (ORR) carbon electrocatalysts with multi-preferred structures (hierarchically porous networks and specific carbon-nitrogen bonds) from carbohydrate-containing small molecules via simple one-step pyrolysis. Based on the step-by-step spontaneous gas-foaming strategy, we successfully prepare 3D hierarchically porous networks with tunable N sites (N_P/N_G ≈ 1:1) by pyrolyzing diverse carbohydrates (glucose, maltose, and cyclodextrin) using nonmetal-metal dual inorganic sacrificial templates. In situ evaporation templates can simplify the procedure of the experiments and avoid the active site loss compared with traditional hard templates. Crucially, dual inorganic sacrificial templates can induce abundant defects and microscopic pore structures (the specific surface area increased from 922.403 to 1898.792 m²·g^-1) and tunable N sites compared with single nonmetal sacrificial templates. The regulatory mechanism of dual inorganic templates on N sites (N_P/N_G ≈ 1:1) is independent of the polymeric state of carbohydrate precursors or even the carbonization condition of the pyrolysis process. A series of carbon materials prepared by this strategy all have ORR-preferred structures and exhibit low ORR overpotentials compared with Pt/C. For instance, the Zn-air battery with βCD-DSC-950-1 exhibits an open-circuit potential of 1.51 V and a peak power density of 180.89 mW·cm^-2, higher than those of Pt/C (1.47 V, 174.94 mW·cm^-2). In general, the conversion of carbohydrate-containing small molecules to functional carbon materials provides a new strategy for the development of carbonaceous electrocatalysts.

Co/CoOx heterojunctions encapsulated N-doped carbon sheets via a dual-template-guided strategy as efficient electrocatalysts for rechargeable Zn-air battery

Developing highly efficient oxygen electrocatalysts is of vital importance for rechargeable Zn-air batteries (ZABs). Herein, Co/CoO_x nano-heterojunctions encapsulated into nitrogen-doped carbon sheets (NCS@Co/CoO_x) are fabricated via a dual-template-guided approach by using zeolitic imidazolate frameworks (ZIFs) as templates. The synergistic integration of structural and compositional advantages endows such catalyst with superior catalytic properties to benchmark noble-metal catalysts. To be specific, the hierarchical micro/mesopores affords massive mass transport channels and maximizes the exposure of accessible active sites, whereas the NCS matrix accelerates electron transfer and prevents the self-aggregation of active species during the electrocatalytic reaction. Moreover, abundant and synergistic Co-based active sites (CoO, Co₃O₄, Co-N_x) greatly promote the catalytic activity. As the cathode of both liquid and flexible solid-state ZABs, excellent device properties are achieved, outperforming those assembled with commercial Pt/C+RuO₂ catalyst. This work presents a feasible and cost-effective strategy for developing oxygen electrocatalysts derived from ZIFs templates.

Green algae and gelatine derived nitrogen rich carbon as an outstanding competitor to Pt loaded carbon catalysts

The development of effective catalysts for the oxygen reduction reaction (ORR) is a significant challenge in energy conversion systems, e.g., Zn-air batteries. Herein, green-algae- and gelatine-derived porous, nitrogen-rich carbons were extensively investigated as electrode materials for electrochemical catalytic reactions. These carbon-based catalysts were designed and optimized to create a metal-free catalyst via templating, carbonization, and subsequent removal of the template. The additional incorporation of graphene improved electronic conductivity and enhanced the electrochemical catalytic reaction. Porous carbons with heteroatoms were used as effective platinum-free ORR electrocatalysts for energy conversion; the presence of nitrogen in the carbon provided more active sites for ORR. Our catalyst also displayed notable durability in a rechargeable Zn-air battery energy system. More importantly, the nitrogen-containing porous carbons were found to have comparable ORR performance in alkaline media to commercially available electrocatalysts. The manuscript demonstrates that nitrogen atom insertion is an appropriate approach when aiming to eliminate noble metals from the synthesis route. N-doped carbons are competitive materials compared to reference platinum-based catalysts.

Carbon Anode in Carbon History

This study examines how the several major industries, associated with a carbon artifact production, essentially belong to one, closely knit family. The common parents are the geological fossils called petroleum and coal. The study also reviews the major developments in carbon nanotechnology and electrocatalysis over the last 30 years or so. In this context, the development of various carbon materials with size, dopants, shape, and structure designed to achieve high catalytic electroactivity is reported, and among them recent carbon electrodes with many important features are presented together with their relevant applications in chemical technology, neurochemical monitoring, electrode kinetics, direct carbon fuel cells, lithium ion batteries, electrochemical capacitors, and supercapattery.

Nanostructured Carbon-Nitrogen-Sulfur-Nickel Networks Derived From Polyaniline as Bifunctional Catalysts for Water Splitting

The development of reliable production routes for sustainable hydrogen (H₂), which is an essential feedstock for industrial processes and energy carrier for fuel cells, is needed. It appears to be an unavoidable alternative to significantly reduce the dependence on conventional energy sources based on fossil fuels without increasing the atmospheric CO₂ levels. Among the different power-to-X scenarios to access high purity H₂, the electrochemical approach based on electrolysis looks to be a promising sustainable solution at both the small and large industrial scales. However, the practical realization of this important opportunity faces several challenges, including the efficient design of cost-effective catalytic materials to be used as a cathode with improved intrinsic and durable activity. In this contribution, we report the design and development of efficient nanostructured catalysts for the electrocatalytic hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in aqueous media, whereby noble metal-free elements are embedded in a matrix of a conducting polymer, polyaniline (PANI). To increase the electrical conductivity and further the electrocatalytic ability toward HER of the chemically polymerized PANI in the presence of nickel (II) salt (nitrate), the PANI-based materials have first been stabilized at a mild temperature of 250-350°C in air and then carbonized at 800-1,000°C under nitrogen gas to convert the chemical species into nitrogen, sulfur, nickel, and carbon nanostructured networks (CNNs). Different physicochemical (TGA-DSC, Raman spectroscopy, XRD, SEM, EDX, ICP, CHNS, BET, and XPS) and electrochemical (voltammetry and electrochemical impedance spectrometry) methods have been integrated to characterize the as-synthesized CNNs materials and interrogate the relationship of material-to-performance. It has been found that those synthesis conditions allow for the substantial increase of the electrocatalytic performance toward HER and OER in alkaline media in terms of the onset potential and charge transfer resistance and overpotential at the specific activity of 10 milliamps per square centimeter, thus ranking the present materials among the most efficient noble metal-free catalysts and making them possible candidates for integration in practical low-energy consumption alkaline electrolyzers.

Advanced rechargeable Na–CO2 batteries enabled by a ruthenium@porous carbon composite cathode with enhanced Na2CO3 reversibility

Porous ketjen black-supported ruthenium nanoparticles (Ru@KB) as a cathode for reversible Na–CO₂ batteries with excellent cycling performance.

Marine and Freshwater Feedstocks as a Precursor for Nitrogen-Containing Carbons: A Review

Marine-derived as well as freshwater feedstock offers important benefits, such as abundance, morphological and structural variety, and the presence of multiple elements, including nitrogen and carbon. Therefore, these renewal resources may be useful for obtaining N- and C-containing materials that can be manufactured by various methods, such as pyrolysis and hydrothermal processes supported by means of chemical and physical activators. However, every synthesis concept relies on an efficient transfer of nitrogen and carbon from marine/freshwater feedstock to the final product. This paper reviews the advantages of marine feedstock over synthetic and natural but non-marine resources as precursors for the manufacturing of N-doped activated carbons. The manufacturing procedure influences some crucial properties of nitrogen-doped carbon materials, such as pore structure and the chemical composition of the surface. An extensive review is given on the relationship between carbon materials manufacturing from marine feedstock and the elemental content of nitrogen, together with a description of the chemical bonding of nitrogen atoms at the surface. N-doped carbons may serve as effective adsorbents for the removal of pollutants from the gas or liquid phase. Non-recognized areas of adsorption-based applications for nitrogen-doped carbons are presented, too. The paper proves that nitrogen-doped carbon materials belong to most of the prospective electrode materials for electrochemical energy conversion and storage technologies such as fuel cells, air⁻metal batteries, and supercapacitors, as well as for bioimaging. The reviewed material belongs to the widely understood field of marine biotechnology in relation to marine natural products.

A rational synthesis of hierarchically porous, N-doped carbon from Mg-based MOFs: understanding the link between nitrogen content and oxygen reduction electrocatalysis

Controlled mixtures of novel Mg-based metal-organic frameworks (MOFs) were prepared, with H(+) or K(+) as counterions. A linear relation was found between synthesis pH and K/H ratio in the resultant mixture, establishing the tunability of the synthesis. Upon pyrolysis, these precursor mixtures yield nitrogen-doped, hierarchically porous carbons, which have good activity towards the oxygen reduction reaction (ORR) at pH 13. The nitrogen content varies significantly along the homologous carbon series (>400%, 1.3 at% to 5.7 at%), to a much greater extent than microstructural parameters such as surface area and graphitization. This allows us to isolate the positive correlation between nitrogen content and electrocatalytic oxygen reduction ORR activity in this class of metal-free, N-doped, porous carbons.

Electrospun Thin-Walled CuCo2O4@C Nanotubes as Bifunctional Oxygen Electrocatalysts for Rechargeable Zn-Air Batteries

Rational design of optimal bifunctional oxygen electrocatalyst with low cost and high activity is greatly desired for realization of rechargeable Zn-air batteries. Herein, we fabricate mesoporous thin-walled CuCo₂O₄@C with abundant nitrogen-doped nanotubes via coaxial electrospinning technique. Benefiting from high catalytic activity of ultrasmall CuCo₂O₄ particles, double active specific surface area of mesoporous nanotubes, and strong coupling with N-doped carbon matrix, the obtained CuCo₂O₄@C exhibits outstanding oxygen electrocatalytic activity and stability, in terms of a positive onset potential (0.951 V) for oxygen reduction reaction (ORR) and a low overpotential (327 mV at 10 mA cm^-2) for oxygen evolution reaction (OER). Significantly, when used as cathode catalyst for Zn-air batteries, CuCo₂O₄@C also displays a low charge-discharge voltage gap (0.79 V at 10 mA cm^-2) and a long cycling life (up to 160 cycles for 80 h). With desirable architecture and excellent electrocatalytic properties, the CuCo₂O₄@C is considered a promising electrocatalyst for Zn-air batteries.

Porous yolk-shell microspheres as N-doped carbon matrix for motivating the oxygen reduction activity of oxygen evolution oriented materials

It is highly challenging to explore high-performance bi-functional oxygen electrode catalysts for their practical application in next-generation energy storage and conversion devices. In this work, we synthesize hierarchical N-doped carbon microspheres with porous yolk-shell structure (NCYS) as a metal-free electrocatalyst toward efficient oxygen reduction through a template-free route. The enhanced oxygen reduction performances in both alkaline and acid media profit well from the porous yolk-shell structure as well as abundant nitrogen functional groups. Furthermore, such yolk-shell microspheres can be used as precursor materials to motivate the oxygen reduction activity of oxygen evolution oriented materials to obtain a desirable bi-functional electrocatalyst. To verify its practical utility, Zn-air battery tests are conducted and exhibit satisfactory performance, indicating that this constructed concept for preparation of bi-functional catalyst will afford a promising strategy for exploring novel metal-air battery electrocatalysts.

Unveiling the Catalytic Origin of Nanocrystalline Yttrium Ruthenate Pyrochlore as a Bifunctional Electrocatalyst for Zn-Air Batteries

Zn-air batteries suffer from the slow kinetics of oxygen reduction reaction (ORR) and/or oxygen evolution reaction (OER). Thus, the bifunctional electrocatalysts are required for the practical application of rechargeable Zn-air batteries. In terms of the catalytic activity and structural stability, pyrochlore oxides (A₂[B_2-xA_x]O_7-y) have emerged as promising candidates. However, a limited use of A-site cations (e.g., lead or bismuth cations) of reported pyrochlore catalysts have hampered broad understanding of their catalytic effect and structure. More seriously, the catalytic origin of the pyrochlore structure was not clearly revealed yet. Here, we report the new nanocrystalline yttrium ruthenate (Y₂[Ru_2-xY_x]O_7-y) with pyrochlore structure. The prepared pyrochlore oxide demonstrates comparable catalytic activities in both ORR and OER, compared to that of previously reported metal oxide-based catalysts such as perovskite oxides. Notably, we first find that the catalytic activity of the Y₂[Ru_2-xY_x]O_7-y is associated with the oxidations and corresponding changes of geometric local structures of yttrium and ruthenium ions during electrocatalysis, which were investigated by in situ X-ray absorption spectroscopy (XAS) in real-time. Zn-air batteries using the prepared pyrochlore oxide achieve highly enhanced charge and discharge performance with a stable potential retention for 200 cycles.

Gelatin-Derived Graphene-Silicate Hybrid Materials Are Biocompatible and Synergistically Promote BMP9-Induced Osteogenic Differentiation of Mesenchymal Stem Cells

Graphene-based materials are used in many fields but have found only limited applications in biomedicine, including bone tissue engineering. Here, we demonstrate that novel hybrid materials consisting of gelatin-derived graphene and silicate nanosheets of Laponite (GL) are biocompatible and promote osteogenic differentiation of mesenchymal stem cells (MSCs). Homogeneous cell attachment, long-term proliferation, and osteogenic differentiation of MSCs on a GL-scaffold were confirmed using optical microscopy and scanning electron microscopy. GL-powders made by pulverizing the GL-scaffold were shown to promote bone morphogenetic protein (BMP9)-induced osteogenic differentiation. GL-powders increased the alkaline phosphatase (ALP) activity in immortalized mouse embryonic fibroblasts but decreased the ALP activity in more-differentiated immortalized mouse adipose-derived cells. Note, however, that GL-powders promoted BMP9-induced calcium mineral deposits in both MSC lines, as assessed using qualitative and quantitative alizarin red assays. Furthermore, the expression of chondro-osteogenic regulator markers such as Runx2, Sox9, osteopontin, and osteocalcin was upregulated by the GL-powder, independent of BMP9 stimulation; although the powder synergistically upregulated the BMP9-induced Osterix expression, the adipogenic marker PPARγ was unaffected. Furthermore, in vivo stem cell implantation experiments demonstrated that GL-powder could significantly enhance the BMP9-induced ectopic bone formation from MSCs. Collectively, our results strongly suggest that the GL hybrid materials promote BMP9-induced osteogenic differentiation of MSCs and hold promise for the development of bone tissue engineering platforms.

Fast Diffusion of O2 on Nitrogen-Doped Graphene to Enhance Oxygen Reduction and Its Application for High-Rate Zn-Air Batteries

N-doped graphene (NDG) was investigated for oxygen reduction reaction (ORR) and used as air-electrode catalyst for Zn-air batteries. Electrochemical results revealed a slightly lower kinetic activity but a much larger rate capability for the NDG than commercial 20% Pt/C catalyst. The maximum power density for a Zn-air cell with NDG air cathode reached up to 218 mW cm^-2, which is nearly 1.5 times that of its counterpart with the Pt/C (155 mW cm^-2). The equivalent diffusion coefficient (D_E) of oxygen from electrolyte solution to the reactive sites of NDG was evaluated as about 1.5 times the liquid-phase diffusion coefficient (D_L) of oxygen within bulk electrolyte solution. Combined with experiments and ab initio calculations, this seems counterintuitive reverse ORR of NDG versus Pt/C can be rationalized by a spontaneous adsorption and fast solid-state diffusion of O₂ on ultralarge graphene surface of NDG to enhance effective ORR on N-doped-catalytic-centers and to achieve high-rate performance for Zn-air batteries.

Fe-Cluster Pushing Electrons to N-Doped Graphitic Layers with Fe3C(Fe) Hybrid Nanostructure to Enhance O2 Reduction Catalysis of Zn-Air Batteries

Non-noble metal catalysts with catalytic activity toward oxygen reduction reaction (ORR) comparable or even superior to that of Pt/C are extremely important for the wide application of metal-air batteries and fuel cells. Here, we develop a simple and controllable strategy to synthesize Fe-cluster embedded in Fe₃C nanoparticles (designated as Fe₃C(Fe)) encased in nitrogen-doped graphitic layers (NDGLs) with graphitic shells as a novel hybrid nanostructure as an effective ORR catalyst by directly pyrolyzing a mixture of Prussian blue (PB) and glucose. The pyrolysis temperature was found to be the key parameter for obtaining a stable Fe₃C(Fe)@NDGL core-shell nanostructure with an optimized content of nitrogen. The optimized Fe₃C(Fe)@NDGL catalyst showed high catalytic performance of ORR comparable to that of the Pt/C (20 wt %) catalyst and better stability than that of the Pt/C catalyst in alkaline electrolyte. According to the experimental results and first principle calculation, the high activity of the Fe₃C(Fe)@NDGL catalyst can be ascribed to the synergistic effect of an adequate content of nitrogen doping in graphitic carbon shells and Fe-cluster pushing electrons to NDGL. A zinc-air battery utilizing the Fe₃C(Fe)@NDGL catalyst demonstrated a maximum power density of 186 mW cm^-2, which is slightly higher than that of a zinc-air battery utilizing the commercial Pt/C catalyst (167 mW cm^-2), mostly because of the large surface area of the N-doped graphitic carbon shells. Theoretical calculation verified that O₂ molecules can spontaneously adsorb on both pristine and nitrogen doped graphene surfaces and then quickly diffuse to the catalytically active nitrogen sites. Our catalyst can potentially become a promising replacement for Pt catalysts in metal-air batteries and fuel cells.

Electrically Rechargeable Zinc-Air Batteries: Progress, Challenges, and Perspectives

Zinc-air batteries have attracted much attention and received revived research efforts recently due to their high energy density, which makes them a promising candidate for emerging mobile and electronic applications. Besides their high energy density, they also demonstrate other desirable characteristics, such as abundant raw materials, environmental friendliness, safety, and low cost. Here, the reaction mechanism of electrically rechargeable zinc-air batteries is discussed, different battery configurations are compared, and an in depth discussion is offered of the major issues that affect individual cellular components, along with respective strategies to alleviate these issues to enhance battery performance. Additionally, a section dedicated to battery-testing techniques and corresponding recommendations for best practices are included. Finally, a general perspective on the current limitations, recent application-targeted developments, and recommended future research directions to prolong the lifespan of electrically rechargeable zinc-air batteries is provided.

In situ integration of CoFe alloy nanoparticles with nitrogen-doped carbon nanotubes as advanced bifunctional cathode catalysts for Zn-air batteries

Electrochemical catalysis of O₂-incorporated reactions is a promising strategy for metal-air batteries. The performance of metal-air batteries is determined by the catalytic activities of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Therefore, developing efficient catalysts with superior activities for the ORR and OER is of great significance to expand the application range of metal-air batteries. Herein, CoFe alloy nanoparticles adhered to the inside wall of nitrogen doped carbon nanotubes (CoFe@NCNTs) are synthesized and can function as a Janus particle to efficiently catalyze the ORR and OER with desirable activities in 0.1 M KOH solution. Specifically, the CoFe@NCNTs present an onset potential of 0.95 V and a half-wave potential of 0.84 V as an ORR catalyst. When used as an air-cathode catalyst for a Zn-air battery, the CoFe@NCNTs cathode performs better than a Pt/C cathode, showing a high open-circuit potential of 1.45 V, a maximum power density of 150 mW cm^-2 and an average specific capacity of 808 mA h g_zn^-1 at current densities from 2 mA cm^-2 to 10 mA cm^-2.

Interaction Induced High Catalytic Activities of CoO Nanoparticles Grown on Nitrogen-Doped Hollow Graphene Microspheres for Oxygen Reduction and Evolution Reactions

Nitrogen doped graphene hollow microspheres (NGHSs) have been used as the supports for the growth of the CoO nanoparticles. The nitrogen doped structure favors the nucleation and growth of the CoO nanoparticles and the CoO nanoparticles are mostly anchored on the quaternary nitrogen doped sites of the NGHSs with good monodispersity since the higher electron density of the quaternary nitrogen favors the nucleation and growth of the CoO nanoparticles through its coordination and electrostatic interactions with the Co(2+) ions. The resulting NGHSs supported CoO nanoparticles (CoO/NGHSs) are highly active for the oxygen reduction reaction (ORR) with activity and stability higher than the Pt/C and for the oxygen evolution reaction (OER) with activity and stability comparable to the most efficient catalysts reported to date. This indicates that the CoO/NGHSs could be used as efficient bi-functional catalysts for ORR and OER. Systematic analysis shows that the superior catalytic activities of the CoO/NGHSs for ORR and OER mainly originate from the nitrogen doped structure of the NGHSs, the small size of the CoO nanoparticles, the higher specific and electroactive surface area of the CoO/NGHSs, the good electric conductivity of the CoO/NGHSs, the strong interaction between the CoO nanoparticles and the NGHSs, etc.

Scalable Fabrication of Nanoporous Carbon Fiber Films as Bifunctional Catalytic Electrodes for Flexible Zn-Air Batteries

A flexible nanoporous carbon-fiber film for wearable electronics is prepared by a facile and scalable method through pyrolysis of electrospun polyimide. It exhibits excellent bifunctional electrocatalytic activities for oxygen reduction and oxygen evolution. Flexible rechargeable zinc-air batteries based on the carbon-fiber film show high round-trip efficiency and mechanical stability.

Electrocatalytic performances of g-C3N4-LaNiO3 composite as bi-functional catalysts for lithium-oxygen batteries

A low cost and non-precious metal composite material g-C3N4-LaNiO3 (CNL) was synthesized as a bifunctional electrocatalyst for the air electrode of lithium-oxygen (Li-O2) batteries. The composition strategy changed the electron structure of LaNiO3 and g-C3N4, ensures high Ni(3+)/Ni(2+) ratio and more absorbed hydroxyl on the surface of CNL that can promote the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). The composite catalyst presents higher activities than the individual components g-C3N4 and LaNiO3 for both ORR and OER. In non-aqueous Li-O2 batteries, CNL shows higher capacity, lower overpotentials and better cycling stability than XC-72 carbon and LaNiO3 catalysts. Our results suggest that CNL composite is a promising cathode catalyst for Li-O2 batteries.

Supramolecular gel-assisted synthesis of double shelled Co@CoO@N-C/C nanoparticles with synergistic electrocatalytic activity for the oxygen reduction reaction

Investigating active, stable, and low-cost materials for the oxygen reduction reaction is one of the key challenges in fuel-cell research. In this work, we describe the formation of N-doped carbon shell coated Co@CoO nanoparticles supported on Vulcan XC-72 carbon materials (Co@CoO@N-C/C) based on a simple supramolecular gel-assisted method. The double-shelled Co@CoO@N-C/C core-shell nanoparticles exhibit superior electrocatalytic activities for the oxygen reduction reaction compared to N-doped carbon and cobalt oxides, demonstrating the synergistic effect of the hybrid nanomaterials. Notably, the Co@CoO@N-C/C nanoparticles give rise to a comparable four-electron selectivity, long-term stability, and high methanol tolerance; all show a multi-fold improvement over the commercial Pt/C catalyst. The progress is of great importance in exploring advanced non-precious metal-based electrocatalysts for fuel cell applications.

Nano-Fe3O4 grown on porous carbon and its effect on the oxygen reduction reaction for DMFCs with a polymer fiber membrane

Fe₃O₄ nanoparticles grown on porous carbon are prepared as an oxygen reduction reaction (ORR) catalyst in direct methanol fuel cells (DMFCs) in which a polymer fiber membrane (PFM) is used to replace Nafion membrane.

Ultrafine N-doped carbon nanoparticles with controllable size to enhance electrocatalytic activity for oxygen reduction reaction

The ORR electrocatalytic activity of ultrafine nanoparticles prepared from carbonization ofSterculia scaphigerais significantly improved through a simple hydrothermal treatment.

Cobalt nanoparticles encapsulated in N-doped graphene nanoshells as an efficient cathode electrocatalyst for a mechanical rechargeable zinc–air battery

Air-cathodes with properties of efficiency, durability and low cost are essential for high performance metal–air batteries and fuel cells for practical applications.

N-Doped carbon supported Co3O4 nanoparticles as an advanced electrocatalyst for the oxygen reduction reaction in Al–air batteries

Low cost Co₃O₄/N-KB was proposed as a high performance catalyst for Al-air battery. The full battery using this catalyst in air electrode displayed a high discharge voltage plateau of ~1.52 V, comparable to that of the commercial Pt/C (20wt%).

Surface-Tuned Co3O4 Nanoparticles Dispersed on Nitrogen-Doped Graphene as an Efficient Cathode Electrocatalyst for Mechanical Rechargeable Zinc-Air Battery Application

The most vital component of the fuel cells and metal-air batteries is the electrocatalyst, which can facilitate the oxygen reduction reaction (ORR) at a significantly reduced overpotential. The present work deals with the development of surface-tuned cobalt oxide (Co3O4) nanoparticles dispersed on nitrogen-doped graphene as a potential ORR electrocatalyst possessing some unique advantages. The thermally reduced nitrogen-doped graphene (NGr) was decorated with three different morphologies of Co3O4 nanoparticles, viz., cubic, blunt edged cubic, and spherical, by using a simple hydrothermal method. We found that the spherical Co3O4 nanoparticle supported NGr catalyst (Co3O4-SP/NGr-24h) has acquired a significant activity makeover to display the ORR activity closely matching with the state-of-the-art Pt supported carbon (PtC) catalyst in alkaline medium. Subsequently, the Co3O4-SP/NGr-24h catalyst has been utilized as the air electrode in a Zn-air battery, which was found to show comparable performance to the system derived from PtC. Co3O4-SP/NGr-24h catalyst has shown several hours of flat discharge profile at the discharge rates of 10, 20, and 50 mA/cm(2) with a specific capacity and energy density of ~590 mAh/g-Zn and ~840 Wh/kg-Zn, respectively, in the primary Zn-air battery system. In conjunction, Co3O4-SP/NGr-24h has outperformed as an air electrode in mechanical rechargeable Zn-air battery as well, which has shown consistent flat discharge profile with minimal voltage loss at a discharge rate of 50 mA/cm(2). The present results, thus demonstrate that the proper combination of the tuned morphology of Co3O4 with NGr will be a promising and inexpensive material for efficient and ecofriendly cathodes for Zn-air batteries.

Hydrothermal Synthesis of Boron and Nitrogen Codoped Hollow Graphene Microspheres with Enhanced Electrocatalytic Activity for Oxygen Reduction Reaction

Boron and nitrogen codoped hollow graphene microspheres (NBGHSs), synthesized from a simple template sacrificing method, have been employed as an electrocatalyst for the oxygen reduction reaction (ORR). Because of their specific hollow structure that consists of boron and nitrogen codoped graphene, the NBGHSs can exhibit even high electrocatalytic activity toward ORR than the commercial JM Pt/C 40 wt %. This, along with their higher stability, makes the NBGHSs particularly attractive as the electrocatalyst for the ORR with great potential to replace the commonly used noble-metal-based catalysts.

Egg-Box Structure in Cobalt Alginate: A New Approach to Multifunctional Hierarchical Mesoporous N-Doped Carbon Nanofibers for Efficient Catalysis and Energy Storage

Carbon nanomaterials with both doped heteroatom and porous structure represent a new class of carbon nanostructures for boosting electrochemical application, particularly sustainable electrochemical energy conversion and storage applications. We herein demonstrate a unique large-scale sustainable biomass conversion strategy for the synthesis of earth-abundant multifunctional carbon nanomaterials with well-defined doped heteroatom level and multimodal pores through pyrolyzing electrospinning renewable natural alginate. The key part for our chemical synthesis is that we found that the egg-box structure in cobalt alginate nanofiber can offer new opportunity to create large mesopores (∼10-40 nm) on the surface of nitrogen-doped carbon nanofibers. The as-prepared hierarchical carbon nanofibers with three-dimensional pathway for electron and ion transport are conceptually new as high-performance multifunctional electrochemical materials for boosting the performance of oxygen reduction reaction (ORR), lithium ion batteries (LIBs), and supercapacitors (SCs). In particular, they show amazingly the same ORR activity as commercial Pt/C catalyst and much better long-term stability and methanol tolerance for ORR than Pt/C via a four-electron pathway in alkaline electrolyte. They also exhibit a large reversible capacity of 625 mAh g(-1) at 1 A g(-1), good rate capability, and excellent cycling performance for LIBs, making them among the best in all the reported carbon nanomaterials. They also represent highly efficient carbon nanomaterials for SCs with excellent capacitive behavior of 197 F g(-1) at 1 A g(-1) and superior stability. The present work highlights the importance of biomass-derived multifunctional mesoporous carbon nanomaterials in enhancing electrochemical catalysis and energy storage.